From: CaT <cat@zip.com.au>
To: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: torvalds@osdl.org, linux-ide@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: PDC20267 bug and corruption (was: Re: [BK PATCHES] ide-2.6 update)
Date: Sat, 30 Oct 2004 13:47:45 +1000 [thread overview]
Message-ID: <20041030034745.GA1287@zip.com.au> (raw)
In-Reply-To: <58cb370e04102706512283405@mail.gmail.com>
[-- Attachment #1: Type: text/plain, Size: 11138 bytes --]
On Wed, Oct 27, 2004 at 03:51:14PM +0200, Bartlomiej Zolnierkiewicz wrote:
> http://bugme.osdl.org/show_bug.cgi?id=2494
Tried it via bk7, wasn't it.
Looks like I have found a bug relating to the pdc driver though.
The situation is such: I have 2 HDs connected to a PDC20267 PCI card,
one on each channel, with a master on the primary channel and a slave on
the secondry channel. Accessing each drive individually causes no
problems at all but accessing them simultaneously (like copying data off
one drive onto the other) causes the IDE layer to go to hell in a hand
basket. I can duplicate this each and every time by doing the following:
1. copying a few gig from hde to hdh
2. dd if=/dev/hde of=/dev/null
dd if=/dev/zero of=/dev/hdh
With method #1 I get the following:
Oct 27 00:37:39 nessie kernel: attempt to access beyond end of device
Oct 27 00:37:39 nessie kernel: hdh1: rw=1, want=3034756264, limit=390716802
Oct 27 00:37:40 nessie kernel: Aborting journal on device hdh1.
Oct 27 00:37:40 nessie kernel: ext3_abort called.
Oct 27 00:37:40 nessie kernel: EXT3-fs error (device hdh1): ext3_journal_start: Detected aborted journal
Oct 27 00:37:40 nessie kernel: Remounting filesystem read-only
Oct 27 00:37:40 nessie kernel: EXT3-fs error (device hdh1) in start_transaction: Journal has aborted
With method #2, a whole lot more fun occurs. The logfile I have is big
(almost 400k) so I've compressed it and included it as an attachment.
This is with kernel 2.6.10-rc1-bk7 (no logs survived from me testing
this with rc1-mm2).
My HDs attached are:
/dev/hde:
ATA device, with non-removable media
powers-up in standby; SET FEATURES subcmd spins-up.
Model Number: IC35L060AVV207-0
Serial Number: VNVB01G2RAK8XH
Firmware Revision: V22OA63A
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 3a
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 65535
heads 16 1
sectors/track 63 63
--
CHS current addressable sectors: 4128705
LBA user addressable sectors: 120103200
LBA48 user addressable sectors: 120103200
device size with M = 1024*1024: 58644 MBytes
device size with M = 1000*1000: 61492 MBytes (61 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 52 Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
Release interrupt
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
Automatic Acoustic Management feature set
SET MAX security extension
Address Offset Reserved Area Boot
SET FEATURES subcommand required to spinup after power up
Power-Up In Standby feature set
Advanced Power Management feature set
* READ/WRITE DMA QUEUED
* General Purpose Logging feature set
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
30min for SECURITY ERASE UNIT.
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
/dev/hdh:
ATA device, with non-removable media
Model Number: ST3200822A
Serial Number: 3LJ22Y8F
Firmware Revision: 3.01
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 2
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 65535
heads 16 1
sectors/track 63 63
--
CHS current addressable sectors: 4128705
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 390721968
device size with M = 1024*1024: 190782 MBytes
device size with M = 1000*1000: 200049 MBytes (200 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 128, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 1 determined by CSEL
Checksum: correct
And lspci -vvv output is:
0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 64
Region 0: Memory at 44000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: 40000000-408fffff
Prefetchable memory behind bridge: 41000000-41ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
0000:00:0d.0 Unknown mass storage controller: Promise Technology, Inc. PDC20267 (FastTrak100/Ultra100) (rev 02)
Subsystem: Promise Technology, Inc. Ultra100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 10f0 [size=8]
Region 1: I/O ports at 1800 [size=4]
Region 2: I/O ports at 10f8 [size=8]
Region 3: I/O ports at 1804 [size=4]
Region 4: I/O ports at 1080 [size=64]
Region 5: Memory at 42000000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0e.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1000 [size=128]
Region 1: Memory at 40900000 (32-bit, non-prefetchable) [size=128]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0f.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 20)
Subsystem: Netgear FA310TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 1400 [size=256]
Region 1: Memory at 42100000 (32-bit, non-prefetchable) [size=256]
0000:00:14.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:14.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 10c0 [size=16]
0000:00:14.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 0
Region 4: I/O ports at 1820 [disabled] [size=32]
0000:00:14.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
0000:01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (rev 01) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G200 AGP
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 41000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at 40800000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at 40000000 (32-bit, non-prefetchable) [size=8M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
--
Red herrings strewn hither and yon.
[-- Attachment #2: moo.gz --]
[-- Type: application/octet-stream, Size: 17271 bytes --]
next prev parent reply other threads:[~2004-10-30 3:49 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-10-27 13:07 [BK PATCHES] ide-2.6 update Bartlomiej Zolnierkiewicz
2004-10-27 13:34 ` CaT
2004-10-27 13:51 ` Bartlomiej Zolnierkiewicz
2004-10-27 14:33 ` Mikael Pettersson
2004-10-27 14:49 ` Bartlomiej Zolnierkiewicz
2004-10-30 3:47 ` CaT [this message]
2004-10-30 18:06 ` PDC20267 bug and corruption (was: Re: [BK PATCHES] ide-2.6 update) Bartlomiej Zolnierkiewicz
2004-10-30 23:48 ` CaT
2004-10-27 14:29 ` [BK PATCHES] ide-2.6 update J.A. Magallon
2004-10-27 15:07 ` Bartlomiej Zolnierkiewicz
2004-10-27 16:15 ` Gene Heskett
2004-10-27 16:22 ` Bartlomiej Zolnierkiewicz
2004-10-27 17:05 ` Gene Heskett
2004-10-27 17:02 ` Randy.Dunlap
2004-10-27 18:17 ` Gene Heskett
2004-10-27 17:15 ` Bartlomiej Zolnierkiewicz
2004-10-27 18:19 ` Gene Heskett
2004-10-27 17:20 ` Linus Torvalds
2004-10-27 18:26 ` Gene Heskett
2004-10-27 18:41 ` Linus Torvalds
2004-10-27 19:03 ` Gene Heskett
2004-10-28 6:45 ` Gene Heskett
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20041030034745.GA1287@zip.com.au \
--to=cat@zip.com.au \
--cc=bzolnier@gmail.com \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=torvalds@osdl.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).