Re: Asus A8V , via vt8251 AHCI

["Randy.Dunlap" <rdunlap@xenotime.net>]

On Tue, 1 Nov 2005 21:41:51 -0600 Don Carroll wrote:

> well , I have 2.6.14 running , did fix my lost timer tick problem (another
> issue)  but no go on it with irqpoll , recompiling now without MSI, I am
> attaching a dmesg output

This boot log isn't the one where you tried irqpoll, right?
I.e., it doesn't show that in the message log.


> On Tue, Nov 01, 2005 at 12:42:02PM -0800, Randy.Dunlap wrote:
> > 
> > Please don't drop cc's and/or to's.
> > Back to the mailing list now...
> > 
> > On Tue, 1 Nov 2005, Don Carroll wrote:
> > 
> > > kernel = Mandriva default Linux vcr.star-c.com 2.6.12-12mdksmp #1 SMP Fri Sep 9
> > > 17:20:34 CEST 2005 x86_64 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+
> > > unknown GNU/Linux
> > > attaching default config for mandriva linux , I just edited the ahci.c and
> > > built the module from that , did not do a complete kernel install
> > 
> > The default config is uniprocessor, not SMP.  But your kernel
> > verison string above says SMP...
> > 
> > In either case it looks like it is using local APIC and IO APIC.
> > That's all that's required to cause the problem that I am
> > familiar with.
> > 
> > You can at least do test (a) below (boot with the "irqpoll"
> > option on the kernel command line) and report on that.
> > (without rebuilding the kernel)
> > 
> > Test (b) requires rebuilding the kernel, which is going
> > to be needed to fix this problem (if I'm right about it).
> > 
> > 
> > > On Tue, Nov 01, 2005 at 07:40:06AM -0800, Randy.Dunlap wrote:
> > > > On Tue, 1 Nov 2005, Don Carroll wrote:
> > > >
> > > > > Hi , I added pci id 3349 to achi.c and I get it to load now
> > > > > ahci version 1.00
> > > > > ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 217
> > > > > PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 9
> > > > > ahci(0000:00:0f.0) AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
> > > > > ahci(0000:00:0f.0) flags: 64bit ncq pm led clo pmp pio slum part
> > > > > ata3: SATA max UDMA/133 cmd 0xFFFFC20000038900 ctl 0x0 bmdma 0x0 irq 217
> > > > > ata4: SATA max UDMA/133 cmd 0xFFFFC20000038980 ctl 0x0 bmdma 0x0 irq 217
> > > > > ata5: SATA max UDMA/133 cmd 0xFFFFC20000038A00 ctl 0x0 bmdma 0x0 irq 217
> > > > > ata6: SATA max UDMA/133 cmd 0xFFFFC20000038A80 ctl 0x0 bmdma 0x0 irq 217
> > > > > ata3: no device found (phy stat 00000000)
> > > > > scsi2 : ahci
> > > > > ata4: no device found (phy stat 00000000)
> > > > > scsi3 : ahci
> > > > > ata5: no device found (phy stat 00000000)
> > > > > scsi4 : ahci
> > > > > ata6 is slow to respond, please be patient
> > > > > ata6 failed to respond (30 secs)
> > > > > scsi5 : ahci
> > > > >
> > > > > I have a drive on ata6 , but it does not respond , timesout
> > > > >
> > > > > this is Mandriva 2006 x86_64 and it has 2.6.12 I have not been able to get .14
> > > > > to compile yet , does this look like something that ahci 1.01 would help , any
> > > > > ideas ?
> > > >
> > > > Yes.
> > > > (a) boot with "irqpoll" added to the kernel command line to see
> > > > if the kernel can route the missed interrupts.
> > > >
> > > > different test:
> > > > (b) Disable CONFIG_PCI_MSI and reboot/retest (without "irqpoll").
> > > >
> > > > and report the results of those.
> > > >
> > > > What are your configs for SMP and APIC options?
> > > >
> > > > --
> > > > ~Randy
> 


---
~Randy