From mboxrd@z Thu Jan 1 00:00:00 1970 From: Helmut Toplitzer Subject: Re: [linux-usb-devel] Re: BUG?: VIA IDE transfer-rate problem Date: Fri, 20 Jan 2006 16:44:19 +0100 Message-ID: <200601201644.19916.pvrusb2@toplitzer.net> References: <200601201227.27000.pvrusb2@toplitzer.net> <43D0FD98.4080406@keyaccess.nl> Mime-Version: 1.0 Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 7bit Return-path: Received: from toplitzer.net ([83.151.30.110]:11727 "EHLO toplitzer.net") by vger.kernel.org with ESMTP id S1750808AbWATPoY (ORCPT ); Fri, 20 Jan 2006 10:44:24 -0500 In-Reply-To: <43D0FD98.4080406@keyaccess.nl> Content-Disposition: inline Sender: linux-ide-owner@vger.kernel.org List-Id: linux-ide@vger.kernel.org To: Rene Herman Cc: Alan Stern , Bartlomiej Zolnierkiewicz , linux-ide@vger.kernel.org, dbrownell@users.sourceforge.net, linux-usb-devel@lists.sourceforge.net > experiencing the same problem after all. I feel so alone again... However, at least temperatur goes slightly up (2K) wenn i load ehci-hcd and I can confirm the ASYNC problem: bus pci, device 0000:00:10.3 (driver 10 Dec 2004) EHCI Host Controller EHCI 1.00, hcd state 1 ownership 01000001 linux SMI sts/enable 0xe0080000 structural params 0x00003206 capability params 0x00006872 status 0008 FLR command 010009 (park)=0 ithresh=1 period=256 RUN intrenable 37 IAA FATAL PCD ERR INT uframe 0bb4 port 1 status 001000 POWER sig=se0 port 2 status 001000 POWER sig=se0 port 3 status 001000 POWER sig=se0 port 4 status 001005 POWER sig=se0 PE CONNECT port 5 status 001000 POWER sig=se0 port 6 status 001000 POWER sig=se0 irq normal 963 err 0 reclaim 452 (lost 17) complete 964 unlink 0 bus pci, device 0000:00:10.3 (driver 10 Dec 2004) EHCI Host Controller EHCI 1.00, hcd state 1 ownership 01000001 linux SMI sts/enable 0xe0080000 structural params 0x00003206 capability params 0x00006872 status a008 Async Recl FLR command 010009 (park)=0 ithresh=1 period=256 RUN intrenable 37 IAA FATAL PCD ERR INT uframe 3851 port 1 status 001000 POWER sig=se0 port 2 status 001000 POWER sig=se0 port 3 status 001000 POWER sig=se0 port 4 status 001005 POWER sig=se0 PE CONNECT port 5 status 001000 POWER sig=se0 port 6 status 001000 POWER sig=se0 irq normal 963 err 0 reclaim 452 (lost 17) complete 964 unlink 0 So there at least some similarities. Helmut -- My GNUpg fingerprint http://www.gnupg.org 4563 F4FB 0B7E 8698 53CD 00E9 E319 35BD 6A91 1656