From mboxrd@z Thu Jan 1 00:00:00 1970 From: Jochen Heuer Subject: Bug or HW? ata1: command timeout, stat 0x50 host_stat 0x4 Date: Tue, 27 Jun 2006 20:43:20 +0200 Message-ID: <20060627184320.GA16782@planetzork.ping.de> Mime-Version: 1.0 Content-Type: multipart/mixed; boundary="BXVAT5kNtrzKuDFl" Return-path: Received: from lilly.ping.de ([83.97.42.2]:56071 "HELO lilly.ping.de") by vger.kernel.org with SMTP id S1030280AbWF0SnL (ORCPT ); Tue, 27 Jun 2006 14:43:11 -0400 Content-Disposition: inline Sender: linux-ide-owner@vger.kernel.org List-Id: linux-ide@vger.kernel.org To: linux-ide@vger.kernel.org --BXVAT5kNtrzKuDFl Content-Type: text/plain; charset=us-ascii Content-Disposition: inline Hi everyone! I have some severe problems on my Athlon X2 system. The problem is that the system sometimes hangs (during plain web browsing). If I wait long enough the system comes to a complete halt so that not even sysrq does work. The system has to be reset and then everything is fine again for some time. Today I was quick enough to switch from X11 to console and check sysrq output. After enabling logging (sysrq+6) I got the following messages on console: ata1: command 0xca timeout, stat 0x50 host_stat 0x4 ata1: status=0x50 { DriveReady SeekComplete } ata1: command 0xea timeout, stat 0x50 host_stat 0x0 ata1: status=0x50 { DriveReady SeekComplete } Then the system was frozen again and only reset did help. Log files don't contain any infos which makes sense since ata1 is the disk with the OS and where metalog should save log files ... Some infos to my system: Asus A8V with Athlon X2 3800 and 2GB memory current kernel 2.6.17 with SMP compiled I had hoped 2.6.17 would fix this since I seem to remember some fixes for libata with similar error messages. But at least on my system it did not. I will include some infos which might be useful. Just let me know if you need further infos. Best regards, Jochen -- Well, yeah ... I suppose there's no point in getting greedy, is there? << Calvin & Hobbes >> --BXVAT5kNtrzKuDFl Content-Type: text/plain; charset=us-ascii Content-Disposition: attachment; filename="dmesg.txt" Linux version 2.6.17 (root@planetzork) (gcc version 3.4.5 (Gentoo 3.4.5-r1, ssp-3.4.5-1.0, pie-8.7.9)) #1 SMP Mon Jun 19 23:18:01 CEST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable) BIOS-e820: 000000007ffb0000 - 000000007ffc0000 (ACPI data) BIOS-e820: 000000007ffc0000 - 000000007fff0000 (ACPI NVS) BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) 1151MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000ff780 On node 0 totalpages: 524208 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 294832 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v002 ACPIAM ) @ 0x000fa880 ACPI: XSDT (v001 A M I OEMXSDT 0x11000503 MSFT 0x00000097) @ 0x7ffb0100 ACPI: FADT (v003 A M I OEMFACP 0x11000503 MSFT 0x00000097) @ 0x7ffb0290 ACPI: MADT (v001 A M I OEMAPIC 0x11000503 MSFT 0x00000097) @ 0x7ffb0390 ACPI: OEMB (v001 A M I OEMBIOS 0x11000503 MSFT 0x00000097) @ 0x7ffc0040 ACPI: DSDT (v001 A0277 A0277001 0x00000001 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:3 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:3 APIC version 16 ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 88000000 (gap: 80000000:7f780000) Built 1 zonelists Kernel command line: root=/dev/sda2 usbhid.mousepoll=2 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2003.523 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 2074112k/2096832k available (2866k kernel code, 21500k reserved, 788k data, 216k init, 1179328k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4008.84 BogoMIPS (lpj=2004420) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 0(2) -> Core 0 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. Freeing SMP alternatives: 16k freed CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4004.63 BogoMIPS (lpj=2002319) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 1(2) -> Core 1 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02 Total of 2 processors activated (8013.47 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0 checking TSC synchronization across 2 CPUs: Brought up 2 CPUs migration_cost=2000 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1 Setting up standard PCI resources ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Quirk-MSI-K8T Soundcard On PCI: Unexpected Value in PCI-Register: no Change! PCI: enabled onboard AC97/MC97 devices Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: e000-efff MEM window: fbd00000-fbffffff PREFETCH window: e8000000-faffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 6, 262144 bytes) TCP established hash table entries: 262144 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered Machine check exception polling timer started. highmem bounce pool size: 64 pages SGI XFS with no debug enabled Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 radeonfb: Found Intel x86 BIOS ROM Image radeonfb: Retrieved PLL infos from BIOS radeonfb: Reference=0.00 MHz (RefDiv=0) Memory=200.00 Mhz, System=415.49 MHz radeonfb: PLL min 0 max 924844032 radeonfb: No connector info table detected radeonfb: Monitor 1 type CRT found radeonfb: EDID probed radeonfb: Monitor 2 type CRT found mtrr: base(0xe8000000) is not aligned on a size(0x10000000) boundary radeonfb (0000:01:00.0): ATI Radeon JP ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected AGP bridge 0 agpgart: AGP aperture is 128M @ 0xe0000000 Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Hangcheck: Using monotonic_clock(). Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17 skge 1.5 addr 0xfb900000 irq 17 chip Yukon-Lite rev 9 skge eth0: addr 00:15:f2:18:f0:4f Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 18 PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 2 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: PLEXTOR DVDR PX-755A, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... Probing IDE interface ide1... libata version 1.20 loaded. sata_via 0000:00:0f.0: version 1.1 ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 18 sata_via 0000:00:0f.0: routed to hard irq line 10 ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xB802 bmdma 0xA800 irq 18 ata2: SATA max UDMA/133 cmd 0xB400 ctl 0xB002 bmdma 0xA808 irq 18 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:80ff ata1: dev 0 ATA-7, max UDMA7, 488397168 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_via ata2: SATA link up 1.5 Gbps (SStatus 113) ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:407f ata2: dev 0 ATA-6, max UDMA/133, 390721968 sectors: LBA48 ata2: dev 0 configured for UDMA/133 scsi1 : sata_via Vendor: ATA Model: SAMSUNG SP2504C Rev: VT10 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: ST3200822AS Rev: 3.01 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 > sd 1:0:0:0: Attached scsi disk sdb ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 19 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.4: irq 19, io mem 0xfbc00000 ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 19 PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 3 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: irq 19, io base 0x0000c400 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 19 PCI: VIA IRQ fixup for 0000:00:10.1, from 11 to 3 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: irq 19, io base 0x0000c800 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 19 PCI: VIA IRQ fixup for 0000:00:10.2, from 10 to 3 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: irq 19, io base 0x0000d000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 19 PCI: VIA IRQ fixup for 0000:00:10.3, from 10 to 3 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:10.3: irq 19, io base 0x0000d400 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 1-6: new high speed USB device using ehci_hcd and address 4 usb 1-6: device descriptor read/64, error -71 usb 1-6: device descriptor read/64, error -71 usb 1-6: new high speed USB device using ehci_hcd and address 5 usb 1-6: device descriptor read/64, error -71 usb 1-6: device descriptor read/64, error -71 usb 1-6: new high speed USB device using ehci_hcd and address 6 usb 1-6: device not accepting address 6, error -71 usb 1-6: new high speed USB device using ehci_hcd and address 7 usb 1-6: device not accepting address 7, error -71 usb 2-1: new full speed USB device using uhci_hcd and address 2 usb 2-1: configuration #1 chosen from 1 choice hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected usb 3-2: new full speed USB device using uhci_hcd and address 2 usb 3-2: configuration #1 chosen from 1 choice usb 2-1.1: new low speed USB device using uhci_hcd and address 3 usb 2-1.1: configuration #1 chosen from 1 choice usb 2-1.2: new low speed USB device using uhci_hcd and address 4 usb 2-1.2: configuration #1 chosen from 1 choice usb 2-1.3: new low speed USB device using uhci_hcd and address 5 usb 2-1.3: configuration #1 chosen from 1 choice usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. input: CHICONY HP Basic USB Keyboard as /class/input/input0 input: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-0000:00:10.0-1.1 input: Logitech USB-PS/2 Optical Mouse as /class/input/input1 input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:10.0-1.2 input: No brand HA2 1.0 as /class/input/input2 input: USB HID v1.10 Keyboard [No brand HA2 1.0] on usb-0000:00:10.0-1.3 drivers/usb/input/hid-core.c: couldn't find an input interrupt endpoint usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: raid0 personality registered for level 0 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 Advanced Linux Sound Architecture Driver Version 1.0.11rc4 (Wed Mar 22 10:27:24 2006 UTC). ALSA device list: No soundcards found. ip_conntrack version 2.4 (8192 buckets, 65536 max) - 224 bytes per conntrack ip_conntrack_pptp version 3.1 loaded ip_nat_pptp version 3.0 loaded ip_tables: (C) 2000-2006 Netfilter Core Team ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/ ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.60.2) powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV) powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa (1300 mV) powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV) cpu_init done, current fid 0xc, vid 0x8 Starting balanced_irq Using IPI Shortcut mode drivers/rtc/hctosys.c: unable to open rtc device (rtc0) md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 216k freed EXT3 FS on sda2, internal journal b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully flexcop-pci: will use the HW PID filter. flexcop-pci: card revision 2 ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 20 DVB: registering new adapter (FlexCop Digital TV device). b2c2-flexcop: MAC address = 00:d0:d7:0b:c7:91 b2c2-flexcop: found the stv0299 at i2c address: 0x68 DVB: registering frontend 0 (ST STV0299 DVB-S)... b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by a 'FlexCopIIb' complete XFS mounting filesystem sda3 Ending clean XFS mount for filesystem: sda3 ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:11.5 to 64 usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device ftdi_sio 3-2:1.0: FTDI USB Serial Device converter detected drivers/usb/serial/ftdi_sio.c: Detected FT232BM usb 3-2: FTDI USB Serial Device converter now attached to ttyUSB0 usbcore: registered new driver ftdi_sio drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver hda: ATAPI 94X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(66) Uniform CD-ROM driver Revision: 3.20 w83627hf 9191-0290: Reading VID from GPIO5 skge eth0: enabling interface skge eth0: disabling interface skge eth0: enabling interface skge eth0: Link is up at 1000 Mbps, full duplex, flow control tx and rx parport0: PC-style at 0x378 [PCSPP] parport0: Printer, Hewlett-Packard HP LaserJet 5L lp0: using parport0 (polling). Installing knfsd (copyright (C) 1996 okir@monad.swb.de). --BXVAT5kNtrzKuDFl Content-Type: text/plain; charset=us-ascii Content-Disposition: attachment; filename="scsi.txt" Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: ATA Model: SAMSUNG SP2504C Rev: VT10 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: ATA Model: ST3200822AS Rev: 3.01 Type: Direct-Access ANSI SCSI revision: 05 --BXVAT5kNtrzKuDFl Content-Type: text/plain; charset=us-ascii Content-Disposition: attachment; filename="lspci_vvv.txt" 00:00.0 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge Subsystem: ASUSTeK Computer Inc. A8V Deluxe Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] HyperTransport: Slave or Primary Interface !!! Possibly incomplete decoding Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir- Link Control 0: CFlE- CST- CFE- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13) Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller (Asus) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 01:00.1 Display controller: ATI Technologies Inc R420 [X800XT-PE] (Secondary) Subsystem: ATI Technologies Inc Unknown device 0003 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-