From: "J.A. Magallón" <jamagallon@ono.com>
To: Tejun Heo <htejun@gmail.com>
Cc: "Linux-Kernel, " <linux-kernel@vger.kernel.org>,
linux-ide@vger.kernel.org, Jeff Garzik <jgarzik@pobox.com>
Subject: Re: [2.6.18-rc2-mm1] libata ate one PATA channel
Date: Mon, 31 Jul 2006 17:24:52 +0200 [thread overview]
Message-ID: <20060731172452.76a1b6bd@werewolf.auna.net> (raw)
In-Reply-To: <44CD0E55.4020206@gmail.com>
On Mon, 31 Jul 2006 04:53:57 +0900, Tejun Heo <htejun@gmail.com> wrote:
> J.A. Magallón wrote:
> > Hi...
> >
> > I've been out for more than a week. Just went to try -rc2-mm1 and
> > it ate one ide channel...
> >
> > This was -rc1-mm2:
> > libata version 2.00 loaded.
> > ata_piix 0000:00:1f.1: version 2.00ac6
> > ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
> > PCI: Setting latency timer of device 0000:00:1f.1 to 64
> > ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
> > scsi0 : ata_piix
> > ata1.00: ATAPI, max UDMA/33
> > ata1.01: ATAPI, max MWDMA0, CDB intr
> > ata1.00: configured for PIO3
> > ata1.01: configured for PIO3
> > Vendor: HL-DT-ST Model: DVDRAM GSA-4120B Rev: A111
> > Type: CD-ROM ANSI SCSI revision: 05
> > Vendor: IOMEGA Model: ZIP 250 Rev: 51.G
> > Type: Direct-Access ANSI SCSI revision: 05
> > ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15
> > scsi1 : ata_piix
> > ata2.00: ATA-6, max UDMA/100, 234441648 sectors: LBA48
> > ata2.00: ata2: dev 0 multi count 16
> > ata2.01: ATAPI, max UDMA/33
> > ata2.00: configured for UDMA/33
> > ata2.01: configured for UDMA/33
> > Vendor: ATA Model: ST3120022A Rev: 3.06
> > Type: Direct-Access ANSI SCSI revision: 05
> > Vendor: TOSHIBA Model: DVD-ROM SD-M1712 Rev: 1004
> > Type: CD-ROM ANSI SCSI revision: 05
> > ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
> > ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16
> > PCI: Setting latency timer of device 0000:00:1f.2 to 64
> > ata3: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 16
> > ata4: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 16
> >
> >
> > This is -rc2-mm1, a PATA channel is missing...
> >
> > libata version 2.00 loaded.
> > ata_piix 0000:00:1f.1: version 2.00ac6
> > ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
> > PCI: Setting latency timer of device 0000:00:1f.1 to 64
> > ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
> > scsi0 : ata_piix
> > ata1.00: ATAPI, max UDMA/33
> > ata1.01: ATAPI, max MWDMA0, CDB intr
> > ata1.00: configured for UDMA/33
> > ata1.01: configured for PIO3
> > Vendor: HL-DT-ST Model: DVDRAM GSA-4120B Rev: A111
> > Type: CD-ROM ANSI SCSI revision: 05
> > Vendor: IOMEGA Model: ZIP 250 Rev: 51.G
> > Type: Direct-Access ANSI SCSI revision: 05
> > ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
> > ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16
> > PCI: Setting latency timer of device 0000:00:1f.2 to 64
> > ata2: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 16
> > ata3: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 16
> >
> > Any idea ?
> > Any more info needed ?
>
> lspci -n please
werewolf:~> lspci
00:00.0 Host bridge: Intel Corporation 82875P/E7210 Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corporation 82875P Processor to AGP Controller (rev 02)
00:03.0 PCI bridge: Intel Corporation 82875P/E7210 Processor to PCI to CSA Bridge (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2)
00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600/GeForce 6600 GT] (rev a2)
02:01.0 Ethernet controller: Intel Corporation 82547EI Gigabit Ethernet Controller (LOM)
03:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
03:04.0 RAID bus controller: Promise Technology, Inc. PDC20378 (FastTrak 378/SATA 378) (rev 02)
03:0a.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 06)
03:0a.1 Input device controller: Creative Labs SB Live! Game Port (rev 06)
03:0b.0 Ethernet controller: 3Com Corporation 3c980-C 10/100baseTX NIC [Python-T] (rev 78)
03:0c.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
03:0c.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
werewolf:~> lspci -n
00:00.0 0600: 8086:2578 (rev 02)
00:01.0 0604: 8086:2579 (rev 02)
00:03.0 0604: 8086:257b (rev 02)
00:1d.0 0c03: 8086:24d2 (rev 02)
00:1d.1 0c03: 8086:24d4 (rev 02)
00:1d.2 0c03: 8086:24d7 (rev 02)
00:1d.3 0c03: 8086:24de (rev 02)
00:1d.7 0c03: 8086:24dd (rev 02)
00:1e.0 0604: 8086:244e (rev c2)
00:1f.0 0601: 8086:24d0 (rev 02)
00:1f.1 0101: 8086:24db (rev 02)
00:1f.2 0101: 8086:24d1 (rev 02)
00:1f.3 0c05: 8086:24d3 (rev 02)
00:1f.5 0401: 8086:24d5 (rev 02)
01:00.0 0300: 10de:00f1 (rev a2)
02:01.0 0200: 8086:1019
03:03.0 0c00: 104c:8023
03:04.0 0104: 105a:3373 (rev 02)
03:0a.0 0401: 1102:0002 (rev 06)
03:0a.1 0980: 1102:7002 (rev 06)
03:0b.0 0200: 10b7:9805 (rev 78)
03:0c.0 0400: 109e:036e (rev 11)
03:0c.1 0480: 109e:0878 (rev 11)
> Also, can you report what the kernel says with the
> attached patch applied?
>
I reworked it to look like this:
if (legacy_mode) {
probe_ent = ata_pci_init_legacy_port(pdev, port, legacy_mode);
dev_printk(KERN_INFO, &pdev->dev,
"XXX: legacy_mode probe_ent=%p\n", probe_ent);
} else {
if (n_ports == 2)
probe_ent = ata_pci_init_native_mode(pdev, port, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY);
else
probe_ent = ata_pci_init_native_mode(pdev, port, ATA_PORT_PRIMARY);
dev_printk(KERN_INFO, &pdev->dev,
"XXX: non_legacy_mode n_ports=%d probe_ent=%p\n",n_ports,probe_ent);
}
and got:
libata version 2.00 loaded.
ata_piix 0000:00:1f.1: version 2.00ac6
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
ata_piix 0000:00:1f.1: XXX: legacy_mode probe_ent=f7935c00 <=====================
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
scsi0 : ata_piix
ata1.00: ATAPI, max UDMA/33
ata1.01: ATAPI, max MWDMA0, CDB intr
ata1.00: configured for UDMA/33
ata1.01: configured for PIO3
Vendor: HL-DT-ST Model: DVDRAM GSA-4120B Rev: A111
Type: CD-ROM ANSI SCSI revision: 05
Vendor: IOMEGA Model: ZIP 250 Rev: 51.G
Type: Direct-Access ANSI SCSI revision: 05
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16
ata_piix 0000:00:1f.2: XXX: non_legacy_mode n_ports=2 probe_ent=f7935c00 <====================
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata2: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 16
ata3: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 16
scsi1 : ata_piix
ata2.00: ATA-6, max UDMA/133, 390721968 sectors: LBA48
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
scsi2 : ata_piix
ata3: SATA port has no device.
ATA: abnormal status 0x7F on port 0xC807
Vendor: ATA Model: ST3200822AS Rev: 3.01
Type: Direct-Access ANSI SCSI revision: 05
sata_promise 0000:03:04.0: version 1.04
ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 23 (level, low) -> IRQ 17
sata_promise PATA port found
ata4: SATA max UDMA/133 cmd 0xF8804200 ctl 0xF8804238 bmdma 0x0 irq 17
ata5: SATA max UDMA/133 cmd 0xF8804280 ctl 0xF88042B8 bmdma 0x0 irq 17
ata6: PATA max UDMA/133 cmd 0xF8804300 ctl 0xF8804338 bmdma 0x0 irq 17
I checked the BIOS and ICH is in 'Enhanced' mode, so both pata and both sata
channels are usable for a max of 6 drives.
Any ideas ?
TIA
--
J.A. Magallon <jamagallon()ono!com> \ Software is like sex:
\ It's better when it's free
Mandriva Linux release 2007.0 (Cooker) for i586
Linux 2.6.17-jam04 (gcc 4.1.1 20060724 (prerelease) (4.1.1-3mdk)) #1 SMP PREEMPT
next prev parent reply other threads:[~2006-07-31 15:24 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-07-28 11:45 [2.6.18-rc2-mm1] libata ate one PATA channel J.A. Magallón
2006-07-30 19:53 ` Tejun Heo
2006-07-31 15:24 ` J.A. Magallón [this message]
2006-07-31 16:00 ` Tejun Heo
2006-07-31 16:31 ` Alan Cox
2006-07-31 16:50 ` Tejun Heo
2006-07-31 17:03 ` Tejun Heo
2006-07-31 18:52 ` Alan Cox
2006-07-31 18:52 ` Tejun Heo
2006-07-31 19:05 ` Jeff Garzik
2006-07-31 18:38 ` Alan Cox
2006-07-31 21:41 ` J.A. Magallón
2006-08-01 6:22 ` Andrew Morton
2006-08-01 7:32 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060731172452.76a1b6bd@werewolf.auna.net \
--to=jamagallon@ono.com \
--cc=htejun@gmail.com \
--cc=jgarzik@pobox.com \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).