* [-mm patch] cleanup drivers/ata/Kconfig [not found] <20060813012454.f1d52189.akpm@osdl.org> @ 2006-08-13 21:01 ` Adrian Bunk 2006-08-13 22:46 ` Alan Cox ` (2 more replies) 2006-08-13 23:01 ` 2.6.18-rc4-mm1: ATI SB600 SATA drivers: modpost errors Adrian Bunk 1 sibling, 3 replies; 8+ messages in thread From: Adrian Bunk @ 2006-08-13 21:01 UTC (permalink / raw) To: Andrew Morton, jgarzik, Alan Cox; +Cc: linux-kernel, linux-ide On Sun, Aug 13, 2006 at 01:24:54AM -0700, Andrew Morton wrote: >... > Changes since 2.6.18-rc3-mm2: >... > git-libata-all.patch >... > git trees >... This patch contains the following cleanups: - create a menu for ATA - replace the dependencies on ATA with an "if ATA" as a side effect, this fixes a menu breakage due to SATA_INTEL_COMBINED - fix a typo in the PATA_OPTIDMA prompt - let ATA selet SCSI instead of depending on SCSI this should make it easier for users to enable ATA (similar to USB_STORAGE) Signed-off-by: Adrian Bunk <bunk@stusta.de> --- One issue I noticed while creating this patch is that for the following options the dependency and the prompt don't agree whether the option is EXPERIMENTAL: - SATA_SX4 - PATA_AMD - PATA_HPT3X3 - PATA_SC1200 drivers/ata/Kconfig | 117 ++++++++++++++++++++++---------------------- 1 file changed, 61 insertions(+), 56 deletions(-) --- linux-2.6.18-rc4-mm1/drivers/ata/Kconfig.old 2006-08-13 20:32:42.000000000 +0200 +++ linux-2.6.18-rc4-mm1/drivers/ata/Kconfig 2006-08-13 20:55:16.000000000 +0200 @@ -1,483 +1,488 @@ +menu "ATA device support" config ATA tristate "ATA device support" - depends on SCSI + select SCSI ---help--- If you want to use a ATA hard disk, ATA tape drive, ATA CD-ROM or any other ATA device under Linux, say Y and make sure that you know the name of your ATA host adapter (the card inside your computer that "speaks" the ATA protocol, also called ATA controller), because you will be asked for it. +if ATA + config SATA_AHCI tristate "AHCI SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for AHCI Serial ATA. If unsure, say N. config SATA_SVW tristate "ServerWorks Frodo / Apple K2 SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for Broadcom/Serverworks/Apple K2 SATA support. If unsure, say N. config ATA_PIIX tristate "Intel PIIX/ICH SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for ICH5/6/7/8 Serial ATA. If PATA support was enabled previously, this enables support for select Intel PIIX/ICH PATA host controllers. If unsure, say N. config SATA_MV tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the Marvell Serial ATA family. Currently supports 88SX[56]0[48][01] chips. If unsure, say N. config SATA_NV tristate "NVIDIA SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for NVIDIA Serial ATA. If unsure, say N. config PDC_ADMA tristate "Pacific Digital ADMA support" - depends on ATA && PCI + depends on PCI help This option enables support for Pacific Digital ADMA controllers If unsure, say N. config SATA_QSTOR tristate "Pacific Digital SATA QStor support" - depends on ATA && PCI + depends on PCI help This option enables support for Pacific Digital Serial ATA QStor. If unsure, say N. config SATA_PROMISE tristate "Promise SATA TX2/TX4 support" - depends on ATA && PCI + depends on PCI help This option enables support for Promise Serial ATA TX2/TX4. If unsure, say N. config SATA_SX4 tristate "Promise SATA SX4 support" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for Promise Serial ATA SX4. If unsure, say N. config SATA_SIL tristate "Silicon Image SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for Silicon Image Serial ATA. If unsure, say N. config SATA_SIL24 tristate "Silicon Image 3124/3132 SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for Silicon Image 3124/3132 Serial ATA. If unsure, say N. config SATA_SIS tristate "SiS 964/180 SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for SiS Serial ATA 964/180. If unsure, say N. config SATA_ULI tristate "ULi Electronics SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for ULi Electronics SATA. If unsure, say N. config SATA_VIA tristate "VIA SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for VIA Serial ATA. If unsure, say N. config SATA_VITESSE tristate "VITESSE VSC-7174 / INTEL 31244 SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA. If unsure, say N. config SATA_INTEL_COMBINED bool depends on IDE=y && !BLK_DEV_IDE_SATA && (SATA_AHCI || ATA_PIIX) default y config PATA_ALI tristate "ALi PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the ALi ATA interfaces found on the many ALi chipsets. If unsure, say N. config PATA_AMD tristate "AMD/NVidia PATA support (Experimental)" - depends on ATA && PCI + depends on PCI help This option enables support for the AMD and NVidia PATA interfaces found on the chipsets for Athlon/Athlon64. If unsure, say N. config PATA_ARTOP tristate "ARTOP 6210/6260 PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for ARTOP PATA controllers. If unsure, say N. config PATA_ATIIXP tristate "ATI PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the ATI ATA interfaces found on the many ATI chipsets. If unsure, say N. config PATA_CMD64X tristate "CMD64x PATA support (Very Experimental)" - depends on ATA && PCI&& EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the CMD64x series chips except for the CMD640. If unsure, say N. config PATA_CS5520 tristate "CS5510/5520 PATA support" - depends on ATA && PCI + depends on PCI help This option enables support for the Cyrix 5510/5520 companion chip used with the MediaGX/Geode processor family. If unsure, say N. config PATA_CS5530 tristate "CS5530 PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the Cyrix/NatSemi/AMD CS5530 companion chip used with the MediaGX/Geode processor family. If unsure, say N. config PATA_CS5535 tristate "CS5535 PATA support (Experimental)" - depends on ATA && PCI && X86 && !X86_64 && EXPERIMENTAL + depends on PCI && X86 && !X86_64 && EXPERIMENTAL help This option enables support for the NatSemi/AMD CS5535 companion chip used with the Geode processor family. If unsure, say N. config PATA_CYPRESS tristate "Cypress CY82C693 PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the Cypress/Contaq CY82C693 chipset found in some Alpha systems If unsure, say N. config PATA_EFAR tristate "EFAR SLC90E66 support" - depends on ATA && PCI + depends on PCI help This option enables support for the EFAR SLC90E66 IDE controller found on some older machines. If unsure, say N. config ATA_GENERIC tristate "Generic ATA support" - depends on ATA && PCI + depends on PCI help This option enables support for generic BIOS configured ATA controllers via the new ATA layer If unsure, say N. config PATA_HPT366 tristate "HPT 366/368 PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the HPT 366 and 368 PATA controllers via the new ATA layer. If unsure, say N. config PATA_HPT37X tristate "HPT 370/370A/371/372/374/302 PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the majority of the later HPT PATA controllers via the new ATA layer. If unsure, say N. config PATA_HPT3X2N tristate "HPT 372N/302N PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the N variant HPT PATA controllers via the new ATA layer If unsure, say N. config PATA_HPT3X3 tristate "HPT 343/363 PATA support (Experimental)" - depends on ATA && PCI + depends on PCI help This option enables support for the HPT 343/363 PATA controllers via the new ATA layer If unsure, say N. config PATA_ISAPNP tristate "ISA Plug and Play PATA support (Very Experimental)" - depends on ATA && EXPERIMENTAL && ISAPNP + depends on EXPERIMENTAL && ISAPNP help This option enables support for ISA plug & play ATA controllers such as those found on old soundcards. If unsure, say N. config PATA_IT8172 tristate "IT8172 PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the ITE 8172 PATA controller via the new ATA layer. If unsure, say N. config PATA_IT821X tristate "IT821x PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the ITE 8211 and 8212 PATA controllers via the new ATA layer, including RAID mode. If unsure, say N. config ATA_JMICRON tristate "JMicron non-AHCI support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for Jmicron ATA controllers ports running in non-AHCI mode. Where possible you should set the configuration for AHCI to get better performance config PATA_LEGACY tristate "Legacy ISA PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for ISA/VLB bus legacy PATA ports and allows them to be accessed via the new ATA layer. If unsure, say N. config PATA_TRIFLEX tristate "Compaq Triflex PATA support" - depends on ATA && PCI + depends on PCI help Enable support for the Compaq 'Triflex' IDE controller as found on many Compaq Pentium-Pro systems, via the new ATA layer. If unsure, say N. config PATA_MPIIX tristate "Intel PATA MPIIX support" - depends on ATA && PCI + depends on PCI help This option enables support for MPIIX PATA support. If unsure, say N. config PATA_OLDPIIX tristate "Intel PATA old PIIX support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for old(?) PIIX PATA support. If unsure, say N. config PATA_NETCELL tristate "NETCELL Revolution RAID support" - depends on ATA && PCI + depends on PCI help This option enables support for the Netcell Revolution RAID PATA controller. If unsure, say N. config PATA_NS87410 tristate "Nat Semi NS87410 PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the National Semiconductor NS87410 PCI-IDE controller. If unsure, say N. config PATA_OPTI tristate "OPTI621/6215 PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables full PIO support for the early Opti ATA controllers found on some old motherboards. If unsure, say N. config PATA_OPTIDMA - tristate "OPTI FireStar PATA support (Veyr Experimental)" - depends on ATA && PCI && EXPERIMENTAL + tristate "OPTI FireStar PATA support (Very Experimental)" + depends on PCI && EXPERIMENTAL help This option enables DMA/PIO support for the later OPTi controllers found on some old motherboards and in some latops If unsure, say N. config PATA_PCMCIA tristate "PCMCIA PATA support" - depends on ATA && PCMCIA + depends on PCMCIA help This option enables support for PCMCIA ATA interfaces, including compact flash card adapters via the new ATA layer. If unsure, say N. config PATA_PDC_OLD tristate "Older Promise PATA controller support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the Promise 20246, 20262, 20263, 20265 and 20267 adapters. If unsure, say N. config PATA_QDI tristate "QDI VLB PATA support" - depends on ATA help Support for QDI 6500 and 6580 PATA controllers on VESA local bus. config PATA_RADISYS tristate "RADISYS 82600 PATA support (Very experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the RADISYS 82600 PATA controllers via the new ATA layer If unsure, say N. config PATA_RZ1000 tristate "PC Tech RZ1000 PATA support" - depends on ATA && PCI + depends on PCI help This option enables basic support for the PC Tech RZ1000/1 PATA controllers via the new ATA layer If unsure, say N. config PATA_SC1200 tristate "SC1200 PATA support (Raving Lunatic)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the NatSemi/AMD SC1200 SoC companion chip used with the Geode processor family. If unsure, say N. config PATA_SERVERWORKS tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the Serverworks OSB4/CSB5/CSB6 and HT1000 PATA controllers, via the new ATA layer. If unsure, say N. config PATA_PDC2027X tristate "Promise PATA 2027x support" - depends on ATA && PCI + depends on PCI help This option enables support for Promise PATA pdc20268 to pdc20277 host adapters. If unsure, say N. config PATA_SIL680 tristate "CMD / Silicon Image 680 PATA support" - depends on ATA && PCI + depends on PCI help This option enables support for CMD / Silicon Image 680 PATA. If unsure, say N. config PATA_SIS tristate "SiS PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for SiS PATA controllers If unsure, say N. config PATA_VIA tristate "VIA PATA support" - depends on ATA && PCI + depends on PCI help This option enables support for the VIA PATA interfaces found on the many VIA chipsets. If unsure, say N. config PATA_WINBOND tristate "Winbond SL82C105 PATA support" - depends on ATA && PCI + depends on PCI help This option enables support for SL82C105 PATA devices found in the Netwinder and some other systems If unsure, say N. +endif # ATA + +endmenu # "ATA device support" ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [-mm patch] cleanup drivers/ata/Kconfig 2006-08-13 21:01 ` [-mm patch] cleanup drivers/ata/Kconfig Adrian Bunk @ 2006-08-13 22:46 ` Alan Cox 2006-08-14 22:12 ` Adrian Bunk 2006-08-14 18:28 ` Jeff Garzik 2006-08-15 7:51 ` [-mm " Greg KH 2 siblings, 1 reply; 8+ messages in thread From: Alan Cox @ 2006-08-13 22:46 UTC (permalink / raw) To: Adrian Bunk; +Cc: Andrew Morton, jgarzik, linux-kernel, linux-ide Ar Sul, 2006-08-13 am 23:01 +0200, ysgrifennodd Adrian Bunk: > One issue I noticed while creating this patch is that for the following > options the dependency and the prompt don't agree whether the option > is EXPERIMENTAL: > - SATA_SX4 > - PATA_AMD > - PATA_HPT3X3 > - PATA_SC1200 HPT3x3, SC1200 are experimental AMD is not intended to be any more. Thanks for spotting these. > config ATA_JMICRON > tristate "JMicron non-AHCI support (Experimental)" > - depends on ATA && PCI && EXPERIMENTAL > + depends on PCI && EXPERIMENTAL > help > This option enables support for Jmicron ATA controllers > ports running in non-AHCI mode. Where possible you should > set the configuration for AHCI to get better performance Actually I should mark this as non-experimental too but I'll do that and push it the proper path. > config PATA_LEGACY > tristate "Legacy ISA PATA support (Experimental)" > - depends on ATA && PCI && EXPERIMENTAL > + depends on PCI && EXPERIMENTAL My fault I suspect - shouldn't have been && PCI originally Acked-by: Alan Cox <alan@redhat.com> ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [-mm patch] cleanup drivers/ata/Kconfig 2006-08-13 22:46 ` Alan Cox @ 2006-08-14 22:12 ` Adrian Bunk 0 siblings, 0 replies; 8+ messages in thread From: Adrian Bunk @ 2006-08-14 22:12 UTC (permalink / raw) To: Alan Cox; +Cc: Andrew Morton, jgarzik, linux-kernel, linux-ide On Sun, Aug 13, 2006 at 11:46:19PM +0100, Alan Cox wrote: > Ar Sul, 2006-08-13 am 23:01 +0200, ysgrifennodd Adrian Bunk: > > One issue I noticed while creating this patch is that for the following > > options the dependency and the prompt don't agree whether the option > > is EXPERIMENTAL: > > - SATA_SX4 > > - PATA_AMD > > - PATA_HPT3X3 > > - PATA_SC1200 > > HPT3x3, SC1200 are experimental > AMD is not intended to be any more. > > Thanks for spotting these. >... What's with SATA_SX4? cu Adrian -- Gentoo kernels are 42 times more popular than SUSE kernels among KLive users (a service by SUSE contractor Andrea Arcangeli that gathers data about kernels from many users worldwide). There are three kinds of lies: Lies, Damn Lies, and Statistics. Benjamin Disraeli ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [-mm patch] cleanup drivers/ata/Kconfig 2006-08-13 21:01 ` [-mm patch] cleanup drivers/ata/Kconfig Adrian Bunk 2006-08-13 22:46 ` Alan Cox @ 2006-08-14 18:28 ` Jeff Garzik 2006-08-14 22:33 ` [libata " Adrian Bunk 2006-08-15 7:51 ` [-mm " Greg KH 2 siblings, 1 reply; 8+ messages in thread From: Jeff Garzik @ 2006-08-14 18:28 UTC (permalink / raw) To: Adrian Bunk; +Cc: Andrew Morton, Alan Cox, linux-kernel, linux-ide Adrian Bunk wrote: > On Sun, Aug 13, 2006 at 01:24:54AM -0700, Andrew Morton wrote: >> ... >> Changes since 2.6.18-rc3-mm2: >> ... >> git-libata-all.patch >> ... >> git trees >> ... > > This patch contains the following cleanups: > - create a menu for ATA > - replace the dependencies on ATA with an "if ATA" > as a side effect, this fixes a menu breakage due to SATA_INTEL_COMBINED > - fix a typo in the PATA_OPTIDMA prompt > - let ATA selet SCSI instead of depending on SCSI > this should make it easier for users to enable ATA (similar to USB_STORAGE) > > Signed-off-by: Adrian Bunk <bunk@stusta.de> There have been a bunch of more-important changes to this file. Please wait until Andrew pulls from me, and resend. Thanks, Jeff ^ permalink raw reply [flat|nested] 8+ messages in thread
* [libata patch] cleanup drivers/ata/Kconfig 2006-08-14 18:28 ` Jeff Garzik @ 2006-08-14 22:33 ` Adrian Bunk 0 siblings, 0 replies; 8+ messages in thread From: Adrian Bunk @ 2006-08-14 22:33 UTC (permalink / raw) To: Jeff Garzik; +Cc: Andrew Morton, Alan Cox, linux-kernel, linux-ide On Mon, Aug 14, 2006 at 02:28:12PM -0400, Jeff Garzik wrote: > Adrian Bunk wrote: > >On Sun, Aug 13, 2006 at 01:24:54AM -0700, Andrew Morton wrote: > >>... > >>Changes since 2.6.18-rc3-mm2: > >>... > >> git-libata-all.patch > >>... > >> git trees > >>... > > > >This patch contains the following cleanups: > >- create a menu for ATA > >- replace the dependencies on ATA with an "if ATA" > > as a side effect, this fixes a menu breakage due to SATA_INTEL_COMBINED > >- fix a typo in the PATA_OPTIDMA prompt > >- let ATA selet SCSI instead of depending on SCSI > > this should make it easier for users to enable ATA (similar to > > USB_STORAGE) > > > >Signed-off-by: Adrian Bunk <bunk@stusta.de> > > There have been a bunch of more-important changes to this file. Please > wait until Andrew pulls from me, and resend. Below is a rediff against libata-dev.git#ALL (not including Alans additional suggestions that will be in another patch). > Thanks, > > Jeff cu Adrian <-- snip --> This patch contains the following cleanups: - replace the dependencies on ATA with an "if ATA" as a side effect, this fixes a menu breakage due to SATA_INTEL_COMBINED - fix a typo in the PATA_OPTIDMA prompt - let ATA selet SCSI instead of depending on SCSI this should make it easier for users to enable ATA (similar to USB_STORAGE) Signed-off-by: Adrian Bunk <bunk@stusta.de> --- drivers/ata/Kconfig | 115 ++++++++++++++++++++++---------------------- 1 file changed, 58 insertions(+), 57 deletions(-) --- libata-dev/drivers/ata/Kconfig.old 2006-08-15 00:23:28.000000000 +0200 +++ libata-dev/drivers/ata/Kconfig 2006-08-15 00:28:02.000000000 +0200 @@ -1,483 +1,484 @@ # # SATA/PATA driver configuration # menu "Serial ATA (prod) and Parallel ATA (experimental) drivers" - depends on SCSI config ATA tristate "ATA device support" - depends on SCSI + select SCSI ---help--- If you want to use a ATA hard disk, ATA tape drive, ATA CD-ROM or any other ATA device under Linux, say Y and make sure that you know the name of your ATA host adapter (the card inside your computer that "speaks" the ATA protocol, also called ATA controller), because you will be asked for it. +if ATA + config SATA_AHCI tristate "AHCI SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for AHCI Serial ATA. If unsure, say N. config SATA_SVW tristate "ServerWorks Frodo / Apple K2 SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for Broadcom/Serverworks/Apple K2 SATA support. If unsure, say N. config ATA_PIIX tristate "Intel PIIX/ICH SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for ICH5/6/7/8 Serial ATA. If PATA support was enabled previously, this enables support for select Intel PIIX/ICH PATA host controllers. If unsure, say N. config SATA_MV tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the Marvell Serial ATA family. Currently supports 88SX[56]0[48][01] chips. If unsure, say N. config SATA_NV tristate "NVIDIA SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for NVIDIA Serial ATA. If unsure, say N. config PDC_ADMA tristate "Pacific Digital ADMA support" - depends on ATA && PCI + depends on PCI help This option enables support for Pacific Digital ADMA controllers If unsure, say N. config SATA_QSTOR tristate "Pacific Digital SATA QStor support" - depends on ATA && PCI + depends on PCI help This option enables support for Pacific Digital Serial ATA QStor. If unsure, say N. config SATA_PROMISE tristate "Promise SATA TX2/TX4 support" - depends on ATA && PCI + depends on PCI help This option enables support for Promise Serial ATA TX2/TX4. If unsure, say N. config SATA_SX4 tristate "Promise SATA SX4 support" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for Promise Serial ATA SX4. If unsure, say N. config SATA_SIL tristate "Silicon Image SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for Silicon Image Serial ATA. If unsure, say N. config SATA_SIL24 tristate "Silicon Image 3124/3132 SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for Silicon Image 3124/3132 Serial ATA. If unsure, say N. config SATA_SIS tristate "SiS 964/180 SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for SiS Serial ATA 964/180. If unsure, say N. config SATA_ULI tristate "ULi Electronics SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for ULi Electronics SATA. If unsure, say N. config SATA_VIA tristate "VIA SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for VIA Serial ATA. If unsure, say N. config SATA_VITESSE tristate "VITESSE VSC-7174 / INTEL 31244 SATA support" - depends on ATA && PCI + depends on PCI help This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA. If unsure, say N. config SATA_INTEL_COMBINED bool depends on IDE=y && !BLK_DEV_IDE_SATA && (SATA_AHCI || ATA_PIIX) default y config PATA_ALI tristate "ALi PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the ALi ATA interfaces found on the many ALi chipsets. If unsure, say N. config PATA_AMD tristate "AMD/NVidia PATA support (Experimental)" - depends on ATA && PCI + depends on PCI help This option enables support for the AMD and NVidia PATA interfaces found on the chipsets for Athlon/Athlon64. If unsure, say N. config PATA_ARTOP tristate "ARTOP 6210/6260 PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for ARTOP PATA controllers. If unsure, say N. config PATA_ATIIXP tristate "ATI PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the ATI ATA interfaces found on the many ATI chipsets. If unsure, say N. config PATA_CMD64X tristate "CMD64x PATA support (Very Experimental)" - depends on ATA && PCI&& EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the CMD64x series chips except for the CMD640. If unsure, say N. config PATA_CS5520 tristate "CS5510/5520 PATA support" - depends on ATA && PCI + depends on PCI help This option enables support for the Cyrix 5510/5520 companion chip used with the MediaGX/Geode processor family. If unsure, say N. config PATA_CS5530 tristate "CS5530 PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the Cyrix/NatSemi/AMD CS5530 companion chip used with the MediaGX/Geode processor family. If unsure, say N. config PATA_CS5535 tristate "CS5535 PATA support (Experimental)" - depends on ATA && PCI && X86 && !X86_64 && EXPERIMENTAL + depends on PCI && X86 && !X86_64 && EXPERIMENTAL help This option enables support for the NatSemi/AMD CS5535 companion chip used with the Geode processor family. If unsure, say N. config PATA_CYPRESS tristate "Cypress CY82C693 PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the Cypress/Contaq CY82C693 chipset found in some Alpha systems If unsure, say N. config PATA_EFAR tristate "EFAR SLC90E66 support" - depends on ATA && PCI + depends on PCI help This option enables support for the EFAR SLC90E66 IDE controller found on some older machines. If unsure, say N. config ATA_GENERIC tristate "Generic ATA support" - depends on ATA && PCI + depends on PCI help This option enables support for generic BIOS configured ATA controllers via the new ATA layer If unsure, say N. config PATA_HPT366 tristate "HPT 366/368 PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the HPT 366 and 368 PATA controllers via the new ATA layer. If unsure, say N. config PATA_HPT37X tristate "HPT 370/370A/371/372/374/302 PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the majority of the later HPT PATA controllers via the new ATA layer. If unsure, say N. config PATA_HPT3X2N tristate "HPT 372N/302N PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the N variant HPT PATA controllers via the new ATA layer If unsure, say N. config PATA_HPT3X3 tristate "HPT 343/363 PATA support (Experimental)" - depends on ATA && PCI + depends on PCI help This option enables support for the HPT 343/363 PATA controllers via the new ATA layer If unsure, say N. config PATA_ISAPNP tristate "ISA Plug and Play PATA support (Very Experimental)" - depends on ATA && EXPERIMENTAL && ISAPNP + depends on EXPERIMENTAL && ISAPNP help This option enables support for ISA plug & play ATA controllers such as those found on old soundcards. If unsure, say N. config PATA_IT8172 tristate "IT8172 PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the ITE 8172 PATA controller via the new ATA layer. If unsure, say N. config PATA_IT821X tristate "IT821x PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the ITE 8211 and 8212 PATA controllers via the new ATA layer, including RAID mode. If unsure, say N. config PATA_LEGACY tristate "Legacy ISA PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for ISA/VLB bus legacy PATA ports and allows them to be accessed via the new ATA layer. If unsure, say N. config PATA_TRIFLEX tristate "Compaq Triflex PATA support" - depends on ATA && PCI + depends on PCI help Enable support for the Compaq 'Triflex' IDE controller as found on many Compaq Pentium-Pro systems, via the new ATA layer. If unsure, say N. config PATA_MPIIX tristate "Intel PATA MPIIX support" - depends on ATA && PCI + depends on PCI help This option enables support for MPIIX PATA support. If unsure, say N. config PATA_OLDPIIX tristate "Intel PATA old PIIX support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for old(?) PIIX PATA support. If unsure, say N. config PATA_NETCELL tristate "NETCELL Revolution RAID support" - depends on ATA && PCI + depends on PCI help This option enables support for the Netcell Revolution RAID PATA controller. If unsure, say N. config PATA_NS87410 tristate "Nat Semi NS87410 PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the National Semiconductor NS87410 PCI-IDE controller. If unsure, say N. config PATA_OPTI tristate "OPTI621/6215 PATA support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables full PIO support for the early Opti ATA controllers found on some old motherboards. If unsure, say N. config PATA_OPTIDMA - tristate "OPTI FireStar PATA support (Veyr Experimental)" - depends on ATA && PCI && EXPERIMENTAL + tristate "OPTI FireStar PATA support (Very Experimental)" + depends on PCI && EXPERIMENTAL help This option enables DMA/PIO support for the later OPTi controllers found on some old motherboards and in some latops If unsure, say N. config PATA_PCMCIA tristate "PCMCIA PATA support" - depends on ATA && PCMCIA + depends on PCMCIA help This option enables support for PCMCIA ATA interfaces, including compact flash card adapters via the new ATA layer. If unsure, say N. config PATA_PDC_OLD tristate "Older Promise PATA controller support (Very Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the Promise 20246, 20262, 20263, 20265 and 20267 adapters. If unsure, say N. config PATA_QDI tristate "QDI VLB PATA support" - depends on ATA help Support for QDI 6500 and 6580 PATA controllers on VESA local bus. config PATA_RADISYS tristate "RADISYS 82600 PATA support (Very experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the RADISYS 82600 PATA controllers via the new ATA layer If unsure, say N. config PATA_RZ1000 tristate "PC Tech RZ1000 PATA support" - depends on ATA && PCI + depends on PCI help This option enables basic support for the PC Tech RZ1000/1 PATA controllers via the new ATA layer If unsure, say N. config PATA_SC1200 tristate "SC1200 PATA support (Raving Lunatic)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the NatSemi/AMD SC1200 SoC companion chip used with the Geode processor family. If unsure, say N. config PATA_SERVERWORKS tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for the Serverworks OSB4/CSB5/CSB6 and HT1000 PATA controllers, via the new ATA layer. If unsure, say N. config PATA_PDC2027X tristate "Promise PATA 2027x support" - depends on ATA && PCI + depends on PCI help This option enables support for Promise PATA pdc20268 to pdc20277 host adapters. If unsure, say N. config PATA_SIL680 tristate "CMD / Silicon Image 680 PATA support" - depends on ATA && PCI + depends on PCI help This option enables support for CMD / Silicon Image 680 PATA. If unsure, say N. config PATA_SIS tristate "SiS PATA support (Experimental)" - depends on ATA && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL help This option enables support for SiS PATA controllers If unsure, say N. config PATA_VIA tristate "VIA PATA support" - depends on ATA && PCI + depends on PCI help This option enables support for the VIA PATA interfaces found on the many VIA chipsets. If unsure, say N. config PATA_WINBOND tristate "Winbond SL82C105 PATA support" - depends on ATA && PCI + depends on PCI help This option enables support for SL82C105 PATA devices found in the Netwinder and some other systems If unsure, say N. -endmenu +endif # ATA +endmenu # "ATA drivers" ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [-mm patch] cleanup drivers/ata/Kconfig 2006-08-13 21:01 ` [-mm patch] cleanup drivers/ata/Kconfig Adrian Bunk 2006-08-13 22:46 ` Alan Cox 2006-08-14 18:28 ` Jeff Garzik @ 2006-08-15 7:51 ` Greg KH 2006-08-15 9:39 ` Adrian Bunk 2 siblings, 1 reply; 8+ messages in thread From: Greg KH @ 2006-08-15 7:51 UTC (permalink / raw) To: Adrian Bunk; +Cc: Andrew Morton, jgarzik, Alan Cox, linux-kernel, linux-ide On Sun, Aug 13, 2006 at 11:01:06PM +0200, Adrian Bunk wrote: > On Sun, Aug 13, 2006 at 01:24:54AM -0700, Andrew Morton wrote: > >... > > Changes since 2.6.18-rc3-mm2: > >... > > git-libata-all.patch > >... > > git trees > >... > > This patch contains the following cleanups: > - create a menu for ATA > - replace the dependencies on ATA with an "if ATA" Why do this? Are we going to be doing this for all subsystems? It seems like a bit of unnecessary churn to me... thanks, greg k-h ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [-mm patch] cleanup drivers/ata/Kconfig 2006-08-15 7:51 ` [-mm " Greg KH @ 2006-08-15 9:39 ` Adrian Bunk 0 siblings, 0 replies; 8+ messages in thread From: Adrian Bunk @ 2006-08-15 9:39 UTC (permalink / raw) To: Greg KH; +Cc: Andrew Morton, jgarzik, Alan Cox, linux-kernel, linux-ide On Tue, Aug 15, 2006 at 12:51:44AM -0700, Greg KH wrote: > On Sun, Aug 13, 2006 at 11:01:06PM +0200, Adrian Bunk wrote: > > On Sun, Aug 13, 2006 at 01:24:54AM -0700, Andrew Morton wrote: > > >... > > > Changes since 2.6.18-rc3-mm2: > > >... > > > git-libata-all.patch > > >... > > > git trees > > >... > > > > This patch contains the following cleanups: > > - create a menu for ATA > > - replace the dependencies on ATA with an "if ATA" > > Why do this? Are we going to be doing this for all subsystems? > > It seems like a bit of unnecessary churn to me... The following two are exactly equivalent: <-- snip --> tristate BAR1 "bar1" depends on FOO tristate BAR2 "bar2" depends on FOO <-- snip --> if FOO tristate BAR1 "bar1" tristate BAR2 "bar2" endif <-- snip --> I'd say the latter is a bit better, but there's no reason to convert all subsystems since the two forms are equivalent. In this case, I was looking for a way to fix the breakage of the ATA menu indentation due to SATA_INTEL_COMBINED, and this is the solution I did choose. > thanks, > > greg k-h cu Adrian -- "Is there not promise of rain?" Ling Tan asked suddenly out of the darkness. There had been need of rain for many days. "Only a promise," Lao Er said. Pearl S. Buck - Dragon Seed ^ permalink raw reply [flat|nested] 8+ messages in thread
* 2.6.18-rc4-mm1: ATI SB600 SATA drivers: modpost errors [not found] <20060813012454.f1d52189.akpm@osdl.org> 2006-08-13 21:01 ` [-mm patch] cleanup drivers/ata/Kconfig Adrian Bunk @ 2006-08-13 23:01 ` Adrian Bunk 1 sibling, 0 replies; 8+ messages in thread From: Adrian Bunk @ 2006-08-13 23:01 UTC (permalink / raw) To: Andrew Morton, Anatoli Antonovitch Cc: linux-kernel, Jeff Garzik, Alan Cox, linux-ide, rusty, sam On Sun, Aug 13, 2006 at 01:24:54AM -0700, Andrew Morton wrote: >... > Changes since 2.6.18-rc3-mm2: >... > +ahci-ati-sb600-sata-support-for-various-modes.patch > +atiixp-ati-sb600-ide-support-for-various-modes.patch >... > Misc patches >... <-- snip --> ... MODPOST 1955 modules WARNING: Can't handle masks in drivers/ata/ahci:FFFF05 WARNING: Can't handle masks in drivers/ide/pci/atiixp:FFFF05 ... <-- snip --> cu Adrian -- Gentoo kernels are 42 times more popular than SUSE kernels among KLive users (a service by SUSE contractor Andrea Arcangeli that gathers data about kernels from many users worldwide). There are three kinds of lies: Lies, Damn Lies, and Statistics. Benjamin Disraeli ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2006-08-15 9:39 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <20060813012454.f1d52189.akpm@osdl.org>
2006-08-13 21:01 ` [-mm patch] cleanup drivers/ata/Kconfig Adrian Bunk
2006-08-13 22:46 ` Alan Cox
2006-08-14 22:12 ` Adrian Bunk
2006-08-14 18:28 ` Jeff Garzik
2006-08-14 22:33 ` [libata " Adrian Bunk
2006-08-15 7:51 ` [-mm " Greg KH
2006-08-15 9:39 ` Adrian Bunk
2006-08-13 23:01 ` 2.6.18-rc4-mm1: ATI SB600 SATA drivers: modpost errors Adrian Bunk
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).