From: "Thomas Pfaff" <tpfaff@gmx.net>
To: linux-ide@vger.kernel.org
Subject: CompactFlash on VT6421 PATA (failed to set xfermode)
Date: Mon, 28 Aug 2006 13:38:07 +0200 [thread overview]
Message-ID: <20060828113807.15790@gmx.net> (raw)
I have some trouble with a Hitachi XX.V.3.7 CompactFlash connected to an VIA VT6421 Raid Controller together with kernel 2.6.17.
First i had to add a patch from VIA to support PATA in sata-via.c.
Now i get following error during boot :
libata version 1.20 loaded.
sata_via 0000:00:14.0: version 1.1
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
sata_via 0000:00:14.0: routed to hard irq line 7
ata_device_add: ENTER
ata_host_add: ENTER
ata_port_start: prd alloc, virt cf63e000, dma f63e000
ata1: PATA max UDMA/133 cmd 0xFD00 ctl 0xFD0A bmdma 0xF900 irq 5
ata_host_add: ENTER
ata_port_start: prd alloc, virt cf626000, dma f626000
ata2: PATA max UDMA/133 cmd 0xFC00 ctl 0xFC0A bmdma 0xF908 irq 5
ata_host_add: ENTER
ata_port_start: prd alloc, virt c12e9000, dma 12e9000
ata3: PATA max UDMA/133 cmd 0xFB00 ctl 0xFB0A bmdma 0xF910 irq 5
ata_device_add: probe begin
ata_device_add: ata1: bus probe begin
ata_bus_reset: ENTER, host 1, port 0
ata_bus_softreset: ata1: bus reset via SRST
ata1: disabling port
ata_bus_reset: EXIT
ata_device_add: ata1: bus probe end
scsi0 : sata_via
ata_device_add: ata2: bus probe begin
ata_bus_reset: ENTER, host 2, port 1
ata_bus_softreset: ata2: bus reset via SRST
ata2: disabling port
ata_bus_reset: EXIT
ata_device_add: ata2: bus probe end
scsi1 : sata_via
ata_device_add: ata3: bus probe begin
ata_bus_reset: ENTER, host 3, port 2
ata_bus_softreset: ata3: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_bus_reset: EXIT
ata_dev_read_id: ENTER, host 3, dev 1
ata_dev_select: ENTER, ata3: device 1, wait 1
ata_dev_select: ENTER, ata3: device 1, wait 1
ata_exec_command_pio: ata3: cmd 0xEC
ata_pio_sector: data read
ata_dev_init_params: init dev params
ata_dev_select: ENTER, ata3: device 1, wait 1
ata_tf_load_pio: feat 0x0 nsect 0x30 lba 0x0 0x0 0x0
ata_tf_load_pio: device 0xBE
ata_exec_command_pio: ata3: cmd 0x91
ata_host_intr: ata3: protocol 1 (dev_stat 0x50)
ata_dev_init_params: EXIT, err_mask=0
ata_dev_select: ENTER, ata3: device 1, wait 1
ata_exec_command_pio: ata3: cmd 0xEC
ata_pio_sector: data read
ata_dev_configure: ENTER, host 3, dev 1
ata3: dev 1 cfg 49:0200 82:7000 83:4004 84:4000 85:7000 86:0004 87:4000 88:0000
ata_dump_id: 49==0x0200 53==0x0003 63==0x0000 64==0x0003 75==0x0000
ata_dump_id: 80==0x0000 81==0x0000 82==0x7000 83==0x4004 84==0x4000
ata_dump_id: 88==0x0000 93==0x0000
ata3: dev 1 ATA-0, max PIO4, 500400 sectors: LBA
ata_dev_configure: EXIT, drv_stat = 0x50
ata_dev_set_xfermode: set features - xfer mode
ata_dev_select: ENTER, ata3: device 1, wait 1
ata_tf_load_pio: feat 0x3 nsect 0xC lba 0x0 0x0 0x0
ata_tf_load_pio: device 0xB0
ata_exec_command_pio: ata3: cmd 0xEF
ata_host_intr: ata3: protocol 1 (dev_stat 0x51)
ata_dev_set_xfermode: EXIT, err_mask=1
ata3: failed to set xfermode (err_mask=0x1)
ata_device_add: ata3: bus probe end
scsi2 : sata_via
ata_device_add: host probe begin
ata_device_add: EXIT, returning 3
What does "failed to set xfermode (err_mask=0x1)" means ?
Is this a problem with the CompactFlash card or with the PATA support in sata-via ?
Thank you in advance,
Thomas
--
"Feel free" – 10 GB Mailbox, 100 FreeSMS/Monat ...
Jetzt GMX TopMail testen: http://www.gmx.net/de/go/topmail
next reply other threads:[~2006-08-28 11:38 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-08-28 11:38 Thomas Pfaff [this message]
2006-08-31 12:24 ` CompactFlash on VT6421 PATA (failed to set xfermode) Thomas Pfaff
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060828113807.15790@gmx.net \
--to=tpfaff@gmx.net \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).