[PATCH pata-2.6] sl82c105: DMA support code cleanup (take 4)

[Sergei Shtylyov <sshtylyov@ru.mvista.com>]

Fold the now equivalent code in the ide_dma_check() method into a mere call to
ide_use_dma().  Make config_for_dma() return non-zero if DMA mode has been set
and call it from the ide_dma_check() method instead of ide_dma_on().
Defer writing the DMA timings to the chip registers until DMA is really turned
on (and do not enable IORDY for DMA).
Remove unneeded code from the init_hwif() method, improve its overall looks.
Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and
also use more proper hwif->dma_command, fix printk() and comment in the latter
one as well.  While at it, cleanup style in several places.

---
This patch has also been actually tested at last. :-)

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

 drivers/ide/pci/sl82c105.c |  148 +++++++++++++++++----------------------------
 1 files changed, 59 insertions(+), 89 deletions(-)

Index: linux-2.6/drivers/ide/pci/sl82c105.c
===================================================================
--- linux-2.6.orig/drivers/ide/pci/sl82c105.c
+++ linux-2.6/drivers/ide/pci/sl82c105.c
@@ -100,59 +100,28 @@ static u8 sl82c105_tune_pio(ide_drive_t 
 }
 
 /*
- * Configure the drive and the chipset for DMA
+ * Configure the drive for DMA.
+ * We'll program the chipset only when DMA is actually turned on.
  */
-static int config_for_dma (ide_drive_t *drive)
+static int config_for_dma(ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = HWIF(drive);
-	struct pci_dev *dev = hwif->pci_dev;
-	unsigned int reg;
-
 	DBG(("config_for_dma(drive:%s)\n", drive->name));
 
-	reg = (hwif->channel ? 0x4c : 0x44) + (drive->select.b.unit ? 4 : 0);
-
 	if (ide_config_drive_speed(drive, XFER_MW_DMA_2) != 0)
-		return 1;
-
-	pci_write_config_word(dev, reg, 0x0240);
+		return 0;
 
-	return 0;
+	return ide_dma_enable(drive);
 }
 
 /*
- * Check to see if the drive and
- * chipset is capable of DMA mode
+ * Check to see if the drive and chipset are capable of DMA mode.
  */
-
-static int sl82c105_check_drive (ide_drive_t *drive)
+static int sl82c105_ide_dma_check(ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= HWIF(drive);
-
-	DBG(("sl82c105_check_drive(drive:%s)\n", drive->name));
+	DBG(("sl82c105_ide_dma_check(drive:%s)\n", drive->name));
 
-	do {
-		struct hd_driveid *id = drive->id;
-
-		if (!drive->autodma)
-			break;
-
-		if (!id || !(id->capability & 1))
-			break;
-
-		/* Consult the list of known "bad" drives */
-		if (__ide_dma_bad_drive(drive))
-			break;
-
-		if (id->field_valid & 2) {
-			if ((id->dma_mword & hwif->mwdma_mask) ||
-			    (id->dma_1word & hwif->swdma_mask))
-				return 0;
-		}
-
-		if (__ide_dma_good_drive(drive) && id->eide_dma_time < 150)
-			return 0;
-	} while (0);
+	if (ide_use_dma(drive) && config_for_dma(drive))
+		return 0;
 
 	return -1;
 }
@@ -181,14 +150,14 @@ static inline void sl82c105_reset_host(s
  * This function is called when the IDE timer expires, the drive
  * indicates that it is READY, and we were waiting for DMA to complete.
  */
-static int sl82c105_ide_dma_lost_irq(ide_drive_t *drive)
+static int sl82c105_ide_dma_lostirq(ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = HWIF(drive);
-	struct pci_dev *dev = hwif->pci_dev;
-	u32 val, mask = hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
-	unsigned long dma_base = hwif->dma_base;
+	ide_hwif_t *hwif	= HWIF(drive);
+	struct pci_dev *dev	= hwif->pci_dev;
+	u32 val, mask		= hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
+	u8 dma_cmd;
 
-	printk("sl82c105: lost IRQ: resetting host\n");
+	printk("sl82c105: lost IRQ, resetting host\n");
 
 	/*
 	 * Check the raw interrupt from the drive.
@@ -201,15 +170,15 @@ static int sl82c105_ide_dma_lost_irq(ide
 	 * Was DMA enabled?  If so, disable it - we're resetting the
 	 * host.  The IDE layer will be handling the drive for us.
 	 */
-	val = inb(dma_base);
-	if (val & 1) {
-		outb(val & ~1, dma_base);
+	dma_cmd = inb(hwif->dma_command);
+	if (dma_cmd & 1) {
+		outb(dma_cmd & ~1, hwif->dma_command);
 		printk("sl82c105: DMA was enabled\n");
 	}
 
 	sl82c105_reset_host(dev);
 
-	/* ide_dmaproc would return 1, so we do as well */
+	/* __ide_dma_lostirq would return 1, so we do as well */
 	return 1;
 }
 
@@ -221,10 +190,10 @@ static int sl82c105_ide_dma_lost_irq(ide
  * The generic IDE core will have disabled the BMEN bit before this
  * function is called.
  */
-static void sl82c105_ide_dma_start(ide_drive_t *drive)
+static void sl82c105_dma_start(ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = HWIF(drive);
-	struct pci_dev *dev = hwif->pci_dev;
+	ide_hwif_t *hwif	= HWIF(drive);
+	struct pci_dev *dev	= hwif->pci_dev;
 
 	sl82c105_reset_host(dev);
 	ide_dma_start(drive);
@@ -232,8 +201,8 @@ static void sl82c105_ide_dma_start(ide_d
 
 static int sl82c105_ide_dma_timeout(ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = HWIF(drive);
-	struct pci_dev *dev = hwif->pci_dev;
+	ide_hwif_t *hwif	= HWIF(drive);
+	struct pci_dev *dev	= hwif->pci_dev;
 
 	DBG(("sl82c105_ide_dma_timeout(drive:%s)\n", drive->name));
 
@@ -241,14 +210,20 @@ static int sl82c105_ide_dma_timeout(ide_
 	return __ide_dma_timeout(drive);
 }
 
-static int sl82c105_ide_dma_on (ide_drive_t *drive)
+static int sl82c105_ide_dma_on(ide_drive_t *drive)
 {
+	struct pci_dev *dev	= HWIF(drive)->pci_dev;
+	int rc, reg 		= 0x44 + drive->dn * 4;
+
 	DBG(("sl82c105_ide_dma_on(drive:%s)\n", drive->name));
 
-	if (config_for_dma(drive))
-		return 1;
-	printk(KERN_INFO "%s: DMA enabled\n", drive->name);
-	return __ide_dma_on(drive);
+	rc = __ide_dma_on(drive);
+	if (rc == 0) {
+		pci_write_config_word(dev, reg, 0x0200);
+
+		printk(KERN_INFO "%s: DMA enabled\n", drive->name);
+	}
+	return rc;
 }
 
 static void sl82c105_dma_off_quietly(ide_drive_t *drive)
@@ -272,8 +247,8 @@ static void sl82c105_dma_off_quietly(ide
  */
 static void sl82c105_selectproc(ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = HWIF(drive);
-	struct pci_dev *dev = hwif->pci_dev;
+	ide_hwif_t *hwif	= HWIF(drive);
+	struct pci_dev *dev	= hwif->pci_dev;
 	u32 val, old, mask;
 
 	//DBG(("sl82c105_selectproc(drive:%s)\n", drive->name));
@@ -373,7 +348,7 @@ static unsigned int __devinit init_chips
 }
 
 /*
- * Initialise the chip
+ * Initialise IDE channel
  */
 static void __devinit init_hwif_sl82c105(ide_hwif_t *hwif)
 {
@@ -398,11 +373,6 @@ static void __devinit init_hwif_sl82c105
 	 */
 	hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
 
-	hwif->atapi_dma = 0;
-	hwif->mwdma_mask = 0;
-	hwif->swdma_mask = 0;
-	hwif->autodma = 0;
-
 	if (!hwif->dma_base)
 		return;
 
@@ -412,27 +382,27 @@ static void __devinit init_hwif_sl82c105
 		 * Never ever EVER under any circumstances enable
 		 * DMA when the bridge is this old.
 		 */
-		printk("    %s: Winbond 553 bridge revision %d, BM-DMA disabled\n",
-		       hwif->name, rev);
-	} else {
-		hwif->atapi_dma = 1;
-		hwif->mwdma_mask = 0x04;
-
-		hwif->ide_dma_check = &sl82c105_check_drive;
-		hwif->ide_dma_on = &sl82c105_ide_dma_on;
-		hwif->dma_off_quietly = &sl82c105_dma_off_quietly;
-		hwif->ide_dma_lostirq = &sl82c105_ide_dma_lost_irq;
-		hwif->dma_start = &sl82c105_ide_dma_start;
-		hwif->ide_dma_timeout = &sl82c105_ide_dma_timeout;
-
-		if (!noautodma)
-			hwif->autodma = 1;
-		hwif->drives[0].autodma = hwif->autodma;
-		hwif->drives[1].autodma = hwif->autodma;
-
-		if (hwif->mate)
-			hwif->serialized = hwif->mate->serialized = 1;
+		printk("    %s: Winbond W83C553 bridge revision %d, "
+		       "BM-DMA disabled\n", hwif->name, rev);
+		return;
 	}
+
+	hwif->atapi_dma  = 1;
+	hwif->mwdma_mask = 0x04;
+
+	hwif->ide_dma_check		= &sl82c105_ide_dma_check;
+	hwif->ide_dma_on		= &sl82c105_ide_dma_on;
+	hwif->dma_off_quietly		= &sl82c105_dma_off_quietly;
+	hwif->ide_dma_lostirq		= &sl82c105_ide_dma_lostirq;
+	hwif->dma_start			= &sl82c105_dma_start;
+	hwif->ide_dma_timeout		= &sl82c105_ide_dma_timeout;
+
+	if (!noautodma)
+		hwif->autodma = 1;
+	hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
+
+	if (hwif->mate)
+		hwif->serialized = hwif->mate->serialized = 1;
 }
 
 static ide_pci_device_t sl82c105_chipset __devinitdata = {