Re: HPT366 not enabled by kernel 2.6.21.2

Re: HPT366 not enabled by kernel 2.6.21.2

[Bartlomiej Zolnierkiewicz]

[ adding linux-ide ML and Sergei to cc: ]

Hi,

On Thursday 24 May 2007, Pascal Schmidt wrote:
> 
> Hello!
> 
> I recently upgraded my kernel to 2.6.21 (.1 and .2 with identical
> results) and my second IDE controller, a HPT366 on a PCI card,
> doesn't get enabled any more. The latest previous kernel I used was
> 2.6.19.7, where the HPT366 worked.
> 
> Here's the HPT366 part of the 2.6.21.2 dmesg:
> 
> HPT366: IDE controller at PCI slot 0000:02:0a.0
> ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
> HPT366: chipset revision 1
> HPT366: using 33 MHz PCI clock
> HPT366: 100% native mode on irq 18
> HPT366: neither IDE port enabled (BIOS)
> ACPI: PCI Interrupt 0000:02:0a.1[A] -> GSI 18 (level, low) -> IRQ 18
> HPT366: using 33 MHz PCI clock
> HPT366: neither IDE port enabled (BIOS)
> 
> There is a flash disk connected to the primary channel (master)
> which also shows up in the controller's BIOS screen, so I don't
> think it's true that both ports are disabled.
> 
> Under 2.6.17.9 the "neither IDE port enabled" message doesn't
> happen and hde gets detected.

The fix from Sergei (queued for 2.6.21.3) is here:

http://git.kernel.org/?p=linux/kernel/git/stable/stable-queue.git;a=blob_plain;f=queue-2.6.21/hpt366-don-t-check-enablebits-for-hpt36x.patch;h=0833e0a37e23ed103a18ca93684201e1cb94a0a9

[ it has already been merged into 2.6.22 tree ]

Thanks,
Bart

Re: HPT366 not enabled by kernel 2.6.21.2

[Pascal Schmidt]

Hello again!

> The fix from Sergei (queued for 2.6.21.3) is here:
>
> http://git.kernel.org/?p=linux/kernel/git/stable/stable-queue.git;a=blob_plain;f=queue-2.6.21/hpt366-don-t-check-enablebits-for-hpt36x.patch;h=0833e0a37e23ed103a18ca93684201e1cb94a0a9
>
> [ it has already been merged into 2.6.22 tree ]

Thank you. The patch works for me.

HPT366: IDE controller at PCI slot 0000:02:0a.0
ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
HPT366: chipset revision 1
HPT366: using 33 MHz PCI clock
HPT366: 100% native mode on irq 18
    ide2: BM-DMA at 0xd300-0xd307, BIOS settings: hde:pio, hdf:pio
ACPI: PCI Interrupt 0000:02:0a.1[A] -> GSI 18 (level, low) -> IRQ 18
HPT366: using 33 MHz PCI clock
    ide3: BM-DMA at 0xd600-0xd607, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hde: TOSHIBA THNCF1G02MG, CFA DISK drive
ide2 at 0xd100-0xd107,0xd202 on irq 18

-- 
Ciao,
Pascal