From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
To: Bob Ham <rah@bash.sh>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>, linux-ide@vger.kernel.org
Subject: Re: hpt374 sata (Highpoint Rocket 1540)
Date: Tue, 31 Jul 2007 23:32:10 +0200 [thread overview]
Message-ID: <200707312332.10820.bzolnier@gmail.com> (raw)
In-Reply-To: <1185916925.8484.23.camel@orchid.arb.net>
Hi,
On Tuesday 31 July 2007, Bob Ham wrote:
> On Tue, 2007-07-31 at 21:52 +0400, Sergei Shtylyov wrote:
> > Hello, I wrote:
> >
> > >> I've had a Highpoint Rocket 1540 (not "RocketRAID") SATA controller for
> > >> a while now, using a proprietary binary driver from Highpoint in a linux
> > >> 2.4 kernel. The chipset is an hpt374. The hpt366 driver freezes on
> > >> boot, as reported by others.
> >
> > > Can we see a bootlog please?
> >
> > ... and the output of 'lspci -v' too.
>
> The machine locks hard when the driver is loaded so I can't give a full
> transcription, but here is the driver's output:
>
> HPT374: IDE controller at PCI slot 0000:00:0d.0
> ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 16
> HPT374: chipset revision 7
> HPT374: DPLL base: 48 MHz, f_CNT: 141, assuming 33 MHz PCI
> HPT374: using 50 MHz DPLL clock
> HPT374: 100% native mode on irq 16
> ide2: BM-DMA at 0xec00-0xec07, BIOS settings: hde:DMA, hdf:pio
> ide3: BM-DMA at 0xec08-0xec0f, BIOS settings: hdg:DMA, hdh:pio
> ACPI: PCI Interrupt 0000:00:0d.1[A] -> GSI 16 (level, low) -> IRQ 16
> HPT374: no clock data saved by BIOS
> HPT374: DPLL base: 48 MHz, f_CNT: 93, assuming 33 MHz PCI
> HPT374: using 50 MHz DPLL clock
> ide4: BM-DMA at 0xed00-0xed07, BIOS settings: hdi:DMA, hdj:pio
> ide5: BM-DMA at 0xed08-0xed0f, BIOS settings: hdk:DMA, hdl:pio
>
>
> The pata_hpt37x driver is refusing to work as well but it doesn't crash
> the machine. Here is the relevant error message:
>
> hpt37x: DPLL did not stabilize.
> pata_hpt37x: BIOS has not set timing clocks.
> hpt37x: DPLL did not stabilize.
Does this patch change anything?
[PATCH] hpt366: always tune PIO
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ide/pci/hpt366.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
Index: b/drivers/ide/pci/hpt366.c
===================================================================
--- a/drivers/ide/pci/hpt366.c
+++ b/drivers/ide/pci/hpt366.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/ide/pci/hpt366.c Version 1.10 Jun 29, 2007
+ * linux/drivers/ide/pci/hpt366.c Version 1.11 Jul 29, 2007
*
* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
@@ -1265,10 +1265,10 @@ static void __devinit init_hwif_hpt366(i
if (new_mcr != old_mcr)
pci_write_config_byte(dev, hwif->select_data + 1, new_mcr);
- if (!hwif->dma_base) {
- hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
+ hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
+
+ if (hwif->dma_base == 0)
return;
- }
hwif->ultra_mask = hwif->cds->udma_mask;
hwif->mwdma_mask = 0x07;
next prev parent reply other threads:[~2007-07-31 21:41 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-07-31 11:08 hpt374 sata (Highpoint Rocket 1540) Bob Ham
2007-07-31 12:23 ` Alan Cox
2007-07-31 20:12 ` Bob Ham
2007-07-31 13:29 ` Sergei Shtylyov
2007-07-31 15:35 ` Brad Campbell
2007-07-31 17:52 ` Sergei Shtylyov
2007-07-31 21:22 ` Bob Ham
2007-07-31 21:32 ` Bartlomiej Zolnierkiewicz [this message]
2007-07-31 22:06 ` Bob Ham
2007-08-01 13:40 ` Sergei Shtylyov
2007-08-01 15:52 ` Bob Ham
2007-08-01 15:58 ` Sergei Shtylyov
2007-08-01 17:15 ` Bob Ham
2007-08-01 18:19 ` Sergei Shtylyov
2007-08-01 22:43 ` Alan Cox
2007-08-02 12:41 ` Sergei Shtylyov
2007-08-02 13:12 ` Alan Cox
2007-08-01 21:03 ` Bob Ham
2007-08-01 21:08 ` Sergei Shtylyov
2007-08-01 22:42 ` Alan Cox
2007-08-05 18:10 ` Sergei Shtylyov
2007-08-01 21:07 ` Bartlomiej Zolnierkiewicz
2007-08-01 21:16 ` Sergei Shtylyov
2007-08-01 21:29 ` Bartlomiej Zolnierkiewicz
2007-08-01 16:14 ` Alan Cox
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200707312332.10820.bzolnier@gmail.com \
--to=bzolnier@gmail.com \
--cc=linux-ide@vger.kernel.org \
--cc=rah@bash.sh \
--cc=sshtylyov@ru.mvista.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).