From: Andrew Morton <akpm@linux-foundation.org>
To: Denys <denys@visp.net.lb>
Cc: linux-kernel@vger.kernel.org, linux-ide@vger.kernel.org
Subject: Re: SC1200 failure in 2.6.23 and 2.6.24-rc1-git10
Date: Tue, 6 Nov 2007 22:15:21 -0800 [thread overview]
Message-ID: <20071106221521.4f64a066.akpm@linux-foundation.org> (raw)
In-Reply-To: <20071101213013.M54162@visp.net.lb>
> On Thu, 1 Nov 2007 23:30:13 +0200 "Denys" <denys@visp.net.lb> wrote:
> Finally i got full DMESG with 1GB card till end. Seems not readable too.
>
> Linux version 2.6.24-rc1-git10-embedded (root@homecore.visp.net.lb) (gcc
> version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #1 Thu Nov 1 23:12:53 EET 2007
> BIOS-provided physical RAM map:
> BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
> BIOS-e801: 0000000000100000 - 0000000004000000 (usable)
> 64MB LOWMEM available.
> Zone PFN ranges:
> DMA 0 -> 4096
> Normal 4096 -> 16384
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0 -> 16384
> DMI not present or invalid.
> Allocating PCI resources starting at 10000000 (gap: 04000000:fc000000)
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
> Kernel command line: console=ttyS0,38400n8
> Initializing CPU#0
> PID hash table entries: 256 (order: 8, 1024 bytes)
> Detected 266.627 MHz processor.
> Console: colour dummy device 80x25
> console [ttyS0] enabled
> Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> Memory: 62836k/65536k available (1020k kernel code, 2292k reserved, 317k
> data, 112k init, 0k highmem)
> virtual kernel memory layout:
> fixmap : 0xffffb000 - 0xfffff000 ( 16 kB)
> vmalloc : 0xc4800000 - 0xffff9000 ( 951 MB)
> lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
> .init : 0xc0252000 - 0xc026e000 ( 112 kB)
> .data : 0xc01ff111 - 0xc024e6f4 ( 317 kB)
> .text : 0xc0100000 - 0xc01ff111 (1020 kB)
> Checking if this processor honours the WP bit even in supervisor mode... Ok.
> SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
> Calibrating delay using timer specific routine.. 534.41 BogoMIPS (lpj=1068836)
> Mount-cache hash table entries: 512
> Compat vDSO mapped to ffffe000.
> CPU: NSC Unknown stepping 01
> Checking 'hlt' instruction... OK.
> Freeing SMP alternatives: 0k freed
> net_namespace: 64 bytes
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xfc3ad, last bus=0
> PCI: Using configuration type 1
> Setting up standard PCI resources
> SCSI subsystem initialized
> PCI: Probing PCI hardware
> PCI: Device 0000:00:12.5 not found by BIOS
> Time: tsc clocksource has been installed.
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 2048 (order: 2, 16384 bytes)
> TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
> TCP: Hash tables configured (established 2048 bind 2048)
> TCP reno registered
> scx200: NatSemi SCx200 Driver
> scx200: GPIO base 0xf400
> scx200: Configuration Block base 0x9000
> io scheduler noop registered (default)
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
> serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
> natsemi dp8381x driver, version 2.1, Sept 11, 2006
> originally by Donald Becker <becker@scyld.com>
> 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
> natsemi eth0: NatSemi DP8381[56] at 0x80000000 (0000:00:0e.0),
> 00:0d:b9:00:8a:30, IRQ 10, port TP.
> scsi0 : sc1200
> scsi1 : sc1200
> ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
> ata2: DUMMY
> ata1.00: CFA: SanDisk SDCFH-1024, HDX 3.07, max MWDMA2
> ata1.00: 2001888 sectors, multi 0: LBA
> ata1.00: configured for MWDMA2
> scsi 0:0:0:0: Direct-Access ATA SanDisk SDCFH-10 HDX PQ: 0 ANSI: 5
> sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
> DPO or FUA
> sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
> DPO or FUA
> sda:<4>Clocksource tsc unstable (delta = -334501841 ns)
> Time: pit clocksource has been installed.
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA2
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA2
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA2
> ata1: EH complete
> ata1.00: limiting speed to MWDMA1:PIO4
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA1
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA1
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA1
> sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
> sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
> 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
> 00 00 00 00
> sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
> end_request: I/O error, dev sda, sector 0
> Buffer I/O error on device sda, logical block 0
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA1
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA1
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA1
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA1
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA1
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ata1: soft resetting link
> ata1.00: configured for MWDMA1
> sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
> sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
> 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
> 00 00 00 00
> sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
> end_request: I/O error, dev sda, sector 0
> Buffer I/O error on device sda, logical block 0
> ata1: EH complete
> unable to read partition table
> sd 0:0:0:0: [sda] Attached SCSI removable disk
> scx200_wdt: timer margin 60 seconds
> cpuidle: using governor ladder
> enabling scx200 high-res timer (1 MHz +0 ppm)
> TCP cubic registered
> Time: scx200_hrt clocksource has been installed.
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> Using IPI Shortcut mode
> VFS: Cannot open root device "<NULL>" or unknown-block(8,18)
> Please append a correct "root=" boot option; here are the available
> partitions:
> 0800 1000944 sda driver: sd
> Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-
> block(8,18)
>
(+linux-ide)
So this has never worked on any known kernel?
next parent reply other threads:[~2007-11-07 6:15 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20071101213013.M54162@visp.net.lb>
2007-11-07 6:15 ` Andrew Morton [this message]
2007-11-07 13:27 ` SC1200 failure in 2.6.23 and 2.6.24-rc1-git10 Denys Fedoryshchenko
2007-11-07 15:23 ` James Andrewartha
2007-11-07 16:06 ` Denys Fedoryshchenko
2007-11-07 19:12 ` Mark Lord
2007-11-07 21:22 ` Denys Fedoryshchenko
2007-11-07 22:31 ` Mark Lord
2007-11-07 22:54 ` Alan Cox
2007-11-07 21:36 ` Denys Fedoryshchenko
2007-11-07 23:20 ` Jeff Garzik
2007-11-07 23:24 ` Mark Lord
2007-11-07 23:49 ` Denys Fedoryshchenko
2007-11-08 0:01 ` Denys Fedoryshchenko
2007-11-08 0:30 ` Bartlomiej Zolnierkiewicz
2007-11-08 7:16 ` Denys Fedoryshchenko
2007-11-08 10:48 ` Alan Cox
2007-11-08 16:44 ` Denys Fedoryshchenko
2007-11-08 17:31 ` Jeff Garzik
2007-11-08 19:56 ` Denys Fedoryshchenko
2007-11-08 22:40 ` Alan Cox
2007-11-09 1:44 ` Tejun Heo
[not found] <fa.FFqM2AneKZLH2d3/UIeCMjE/RLE@ifi.uio.no>
2007-11-08 1:41 ` Robert Hancock
2007-11-08 7:01 ` Denys Fedoryshchenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20071106221521.4f64a066.akpm@linux-foundation.org \
--to=akpm@linux-foundation.org \
--cc=denys@visp.net.lb \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).