From: bugme-daemon@bugzilla.kernel.org
To: linux-ide@vger.kernel.org
Subject: [Bug 10086] 2.6.25-rc2 + smartd = hang
Date: Thu, 20 Mar 2008 21:06:32 -0700 (PDT) [thread overview]
Message-ID: <20080321040632.DF1DA11D10A@picon.linux-foundation.org> (raw)
In-Reply-To: <bug-10086-11633@http.bugzilla.kernel.org/>
http://bugzilla.kernel.org/show_bug.cgi?id=10086
gordonfarquharson@gmail.com changed:
What |Removed |Added
----------------------------------------------------------------------------
CC| |gordonfarquharson@gmail.com
------- Comment #5 from gordonfarquharson@gmail.com 2008-03-20 21:06 -------
I tested 2.6.25-rc5-git4 (which includes the commit) on a GLAN Tank
(arm/mach-iop32x), but I still get the following messages when I run smartctl:
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
ide: failed opcode was: 0xb0
The system does not hang (although it never did when I first saw these
messages).
These messages definitely didn't happen with 2.6.24 on this platform.
Linux proteus 2.6.25-rc6-iop32x #1 Thu Mar 20 20:34:04 MDT 2008 armv5tel
GNU/Linux
00:01.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet
Controller (rev 05)
Subsystem: I-O Data Device, Inc. Unknown device d02a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (63750ns min)
Interrupt: pin A routed to IRQ 27
Region 0: Memory at 80000000 (64-bit, non-prefetchable) [size=128K]
Region 2: Memory at 80020000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at 90000080 [size=64]
[virtual] Expansion ROM at 80030000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: e1000
Kernel modules: e1000
00:02.0 Mass storage controller: Artop Electronic Corp ATP865 (rev 10)
Subsystem: Artop Electronic Corp ATP865
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Region 0: I/O ports at 900000c0 [size=8]
Region 1: I/O ports at 900000d0 [size=4]
Region 2: I/O ports at 900000c8 [size=8]
Region 3: I/O ports at 900000d4 [size=4]
Region 4: I/O ports at 90000000 [size=128]
Region 5: Memory at 80050000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 80040000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: AEC62xx_IDE
Kernel modules: aec62xx
00:03.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 8 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at 80051000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:03.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 8 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 29
Region 0: Memory at 80052000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:03.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 68 (4000ns min, 8500ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 29
Region 0: Memory at 80053000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
gordon@proteus:~$ sudo lspci -vvv
[sudo] password for gordon:
00:01.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet
Controller (rev 05)
Subsystem: I-O Data Device, Inc. Unknown device d02a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (63750ns min)
Interrupt: pin A routed to IRQ 27
Region 0: Memory at 80000000 (64-bit, non-prefetchable) [size=128K]
Region 2: Memory at 80020000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at 90000080 [size=64]
[virtual] Expansion ROM at 80030000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple
DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
Kernel driver in use: e1000
Kernel modules: e1000
00:02.0 Mass storage controller: Artop Electronic Corp ATP865 (rev 10)
Subsystem: Artop Electronic Corp ATP865
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Region 0: I/O ports at 900000c0 [size=8]
Region 1: I/O ports at 900000d0 [size=4]
Region 2: I/O ports at 900000c8 [size=8]
Region 3: I/O ports at 900000d4 [size=4]
Region 4: I/O ports at 90000000 [size=128]
Region 5: Memory at 80050000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 80040000 [disabled] [size=64K]
Capabilities: [58] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: AEC62xx_IDE
Kernel modules: aec62xx
00:03.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 8 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at 80051000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:03.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 8 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 29
Region 0: Memory at 80052000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:03.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 68 (4000ns min, 8500ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 29
Region 0: Memory at 80053000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
Module Size Used by
ipv6 289388 10
dm_snapshot 20448 0
dm_mirror 28992 0
dm_mod 65736 2 dm_snapshot,dm_mirror
ext3 138952 2
jbd 49492 1 ext3
mbcache 9216 1 ext3
ide_disk 16544 4
ehci_hcd 34380 0
ohci_hcd 21188 0
aec62xx 4864 0 [permanent]
usbcore 140220 3 ehci_hcd,ohci_hcd
e1000 124064 0
ide_core 105196 2 ide_disk,aec62xx
--
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the assignee for the bug, or are watching the assignee.
next prev parent reply other threads:[~2008-03-21 4:06 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-02-23 22:41 [Bug 10086] New: 2.6.25-rc2 + smartd = hang bugme-daemon
2008-02-25 1:12 ` [Bug 10086] " bugme-daemon
2008-03-03 1:38 ` bugme-daemon
2008-03-03 19:05 ` bugme-daemon
2008-03-19 8:49 ` bugme-daemon
2008-03-21 4:06 ` bugme-daemon [this message]
2008-03-21 4:12 ` bugme-daemon
2008-03-21 11:24 ` bugme-daemon
2008-03-21 11:33 ` bugme-daemon
2008-03-23 4:11 ` bugme-daemon
2008-03-23 13:08 ` bugme-daemon
2008-03-23 15:08 ` bugme-daemon
2008-03-23 21:05 ` bugme-daemon
2008-03-23 22:11 ` bugme-daemon
2008-03-24 13:46 ` bugme-daemon
2008-03-24 15:08 ` bugme-daemon
2008-04-01 6:26 ` bugme-daemon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080321040632.DF1DA11D10A@picon.linux-foundation.org \
--to=bugme-daemon@bugzilla.kernel.org \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).