* Re: Regression: my systems can no longer boot from an ide hard drive
[not found] <201003230801.o2N81UKg009750@alien.loup.net>
@ 2010-03-23 16:17 ` Randy Dunlap
2010-03-24 0:20 ` Robert Hancock
0 siblings, 1 reply; 5+ messages in thread
From: Randy Dunlap @ 2010-03-23 16:17 UTC (permalink / raw)
To: Mike Hayward; +Cc: linux-kernel, ide
[adding linux-ide mailing list]
On Tue, 23 Mar 2010 02:01:30 -0600 Mike Hayward wrote:
> Three identical known good opteron systems can no longer boot freshly
> installed distros from an ide hard drive. The systems have one ide
> drive and eight sata drives. If distro is installed to ide drive,
> Ubuntu 9.10 server moves cursor down the screen twice, then hangs
> while Fedora 12 grub loads but then claims it can't find root to mount
> and it and hangs 'forever'. Numerous distros have all booted fine
> before 2.6.25... I don't know where it went wrong between 25 and 31.
>
> This is despite partitioning with and without lvm, despite making sure
> kernel/boot loader are in partition in first 2 gigs of ide drive.
>
> Both distros boot just fine on each system when os is installed on a
> sata drive so this isn't a hardware defect.
>
> Distro that boots fine from ide:
> Linux opt1 2.6.25-14.fc9.x86_64 #1 SMP Thu May 1 06:06:21 EDT 2008 x86_64 x86_64 x86_64 GNU/Linux
>
> Distros that no longer boot via ide drive:
> Linux opt2 2.6.31-14-server #48-Ubuntu SMP Fri Oct 16 15:07:34 UTC 2009 x86_64 GNU/Linux
> Linux opt3 2.6.31.5-127.fc12.x86_64 #1 SMP Sat Nov 7 21:11:14 EST 2009 x86_64 x86_64 x86_64 GNU/Linux
>
> Maybe this can be worked around with some options to grub or
> kernel... if so, shouldn't distros detect that ide drives are being
> set up and configure the boot loader properly? It would be very hard
> for newbie to figure this one out.
>
> Has anyone else seen this, or am I the only one who boots from ide
> when a sata drive is present? :-)
>
> - Mike
---
~Randy
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Regression: my systems can no longer boot from an ide hard drive
2010-03-23 16:17 ` Regression: my systems can no longer boot from an ide hard drive Randy Dunlap
@ 2010-03-24 0:20 ` Robert Hancock
2010-03-24 0:46 ` Mike Hayward
0 siblings, 1 reply; 5+ messages in thread
From: Robert Hancock @ 2010-03-24 0:20 UTC (permalink / raw)
To: Randy Dunlap; +Cc: Mike Hayward, linux-kernel, ide
On 03/23/2010 10:17 AM, Randy Dunlap wrote:
> [adding linux-ide mailing list]
>
> On Tue, 23 Mar 2010 02:01:30 -0600 Mike Hayward wrote:
>
>> Three identical known good opteron systems can no longer boot freshly
>> installed distros from an ide hard drive. The systems have one ide
>> drive and eight sata drives. If distro is installed to ide drive,
>> Ubuntu 9.10 server moves cursor down the screen twice, then hangs
>> while Fedora 12 grub loads but then claims it can't find root to mount
>> and it and hangs 'forever'. Numerous distros have all booted fine
>> before 2.6.25... I don't know where it went wrong between 25 and 31.
>>
>> This is despite partitioning with and without lvm, despite making sure
>> kernel/boot loader are in partition in first 2 gigs of ide drive.
>>
>> Both distros boot just fine on each system when os is installed on a
>> sata drive so this isn't a hardware defect.
>>
>> Distro that boots fine from ide:
>> Linux opt1 2.6.25-14.fc9.x86_64 #1 SMP Thu May 1 06:06:21 EDT 2008 x86_64 x86_64 x86_64 GNU/Linux
>>
>> Distros that no longer boot via ide drive:
>> Linux opt2 2.6.31-14-server #48-Ubuntu SMP Fri Oct 16 15:07:34 UTC 2009 x86_64 GNU/Linux
>> Linux opt3 2.6.31.5-127.fc12.x86_64 #1 SMP Sat Nov 7 21:11:14 EST 2009 x86_64 x86_64 x86_64 GNU/Linux
>>
>> Maybe this can be worked around with some options to grub or
>> kernel... if so, shouldn't distros detect that ide drives are being
>> set up and configure the boot loader properly? It would be very hard
>> for newbie to figure this one out.
Most likely the IDE drive isn't being detected properly, but we need
more info on the hardware. Can you post the dmesg output from bootup
with a working kernel? (If you can, the boot messages from the ones that
fail to boot would be ideal. For the Fedora one, you can edit the kernel
command line in grub and take the "quiet" off the end to see more of
them on the screen, any ata output would be useful..)
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Regression: my systems can no longer boot from an ide hard drive
2010-03-24 0:20 ` Robert Hancock
@ 2010-03-24 0:46 ` Mike Hayward
2010-03-24 23:47 ` Robert Hancock
0 siblings, 1 reply; 5+ messages in thread
From: Mike Hayward @ 2010-03-24 0:46 UTC (permalink / raw)
To: hancockrwd; +Cc: randy.dunlap, linux-ide
> Most likely the IDE drive isn't being detected properly, but we need
> more info on the hardware. Can you post the dmesg output from bootup
> with a working kernel? (If you can, the boot messages from the ones that
> fail to boot would be ideal. For the Fedora one, you can edit the kernel
> command line in grub and take the "quiet" off the end to see more of
> them on the screen, any ata output would be useful..)
Ok, here goes with a working ubuntu system. Getting logs from failed
to boot systems is a challenge; none of the Fedora logs had anything
obvious to me at the tail but I couldn't review them all. Systems are
production so I couldn't keep offline after weekend.
This is from literally the same exact installation process except to a
different drive. The ide hard drive works just fine after booting
from sata. Hopefully boot messages can help. Any ideas why Ubuntu
didn't even bring up grub when pressing keys? I am not so familiar
with it, but guessing boot loader wedged before kernel bootstrap.
- Mike
Mar 23 10:44:19 opt2 kernel: imklog 4.2.0, log source = /var/run/rsyslog/kmsg started.
Mar 23 10:44:19 opt2 rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="646" x-info="http://www.rsyslog.com"] (re)start
Mar 23 10:44:19 opt2 rsyslogd: rsyslogd's groupid changed to 103
Mar 23 10:44:20 opt2 rsyslogd: rsyslogd's userid changed to 101
Mar 23 10:44:19 opt2 rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Initializing cgroup subsys cpuset
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Initializing cgroup subsys cpu
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Linux version 2.6.31-14-server (buildd@crested) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu8) ) #48-Ubuntu SMP Fri Oct 16 15:07:34 UTC 2009 (Ubuntu 2.6.31-14.48-server)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.31-14-server root=UUID=17f0eb6b-217b-440e-8289-6162ed85da7f ro quiet splash
Mar 23 10:44:20 opt2 kernel: [ 0.000000] KERNEL supported cpus:
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Intel GenuineIntel
Mar 23 10:44:20 opt2 kernel: [ 0.000000] AMD AuthenticAMD
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Centaur CentaurHauls
Mar 23 10:44:20 opt2 kernel: [ 0.000000] BIOS-provided physical RAM map:
Mar 23 10:44:20 opt2 kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] BIOS-e820: 000000007fff0000 - 000000007ffff000 (ACPI data)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] BIOS-e820: 000000007ffff000 - 0000000080000000 (ACPI NVS)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] DMI 2.3 present.
Mar 23 10:44:20 opt2 kernel: [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
Mar 23 10:44:20 opt2 kernel: [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] last_pfn = 0x7fff0 max_arch_pfn = 0x400000000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] MTRR default type: uncachable
Mar 23 10:44:20 opt2 kernel: [ 0.000000] MTRR fixed ranges enabled:
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 00000-9FFFF write-back
Mar 23 10:44:20 opt2 kernel: [ 0.000000] A0000-EFFFF uncachable
Mar 23 10:44:20 opt2 kernel: [ 0.000000] F0000-FFFFF write-protect
Mar 23 10:44:20 opt2 kernel: [ 0.000000] MTRR variable ranges enabled:
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 0 base 0000000000 mask FF80000000 write-back
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 1 disabled
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 2 disabled
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 3 disabled
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 4 disabled
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 5 disabled
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 6 disabled
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 7 disabled
Mar 23 10:44:20 opt2 kernel: [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Scanning 0 areas for low memory corruption
Mar 23 10:44:20 opt2 kernel: [ 0.000000] modified physical RAM map:
Mar 23 10:44:20 opt2 kernel: [ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] modified: 0000000000010000 - 000000000009fc00 (usable)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] modified: 00000000000e0000 - 0000000000100000 (reserved)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] modified: 0000000000100000 - 000000007fff0000 (usable)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] modified: 000000007fff0000 - 000000007ffff000 (ACPI data)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] modified: 000000007ffff000 - 0000000080000000 (ACPI NVS)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] modified: 00000000ff7c0000 - 0000000100000000 (reserved)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] initial memory mapped : 0 - 20000000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] init_memory_mapping: 0000000000000000-000000007fff0000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Using x86 segment limits to approximate NX protection
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 0000000000 - 007fe00000 page 2M
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 007fe00000 - 007fff0000 page 4k
Mar 23 10:44:20 opt2 kernel: [ 0.000000] kernel direct mapping tables up to 7fff0000 @ 10000-14000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] RAMDISK: 37957000 - 37fefbb8
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: RSDP 00000000000f4620 00014 (v00 ACPIAM)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: RSDT 000000007fff0000 00034 (v01 A M I OEMRSDT 10000304 MSFT 00000097)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: FACP 000000007fff0200 00081 (v02 A M I OEMFACP 10000304 MSFT 00000097)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: DSDT 000000007fff0400 03086 (v01 0AAAA 0AAAA000 00000000 INTL 02002026)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: FACS 000000007ffff000 00040
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: APIC 000000007fff0380 00074 (v01 A M I OEMAPIC 10000304 MSFT 00000097)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: OEMB 000000007ffff040 0005E (v01 A M I OEMBIOS 10000304 MSFT 00000097)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: ASF! 000000007fff3490 00086 (v16 AMIASF AMDSTRET 00000001 INTL 02002026)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Scanning NUMA topology in Northbridge 24
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Number of nodes 2
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Node 0 MemBase 0000000000000000 Limit 0000000040000000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Node 1 MemBase 0000000040000000 Limit 000000007fff0000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] NUMA: Using 30 for the hash shift.
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Using node hash shift of 30
Mar 23 10:44:20 opt2 kernel: [ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Bootmem setup node 0 0000000000000000-0000000040000000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] NODE_DATA [0000000000012000 - 0000000000016fff]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] bootmap [0000000000017000 - 000000000001efff] pages 8
Mar 23 10:44:20 opt2 kernel: [ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 0040000000]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #2 [0001000000 - 00019e0ccc] TEXT DATA BSS ==> [0001000000 - 00019e0ccc]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #3 [0037957000 - 0037fefbb8] RAMDISK ==> [0037957000 - 0037fefbb8]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #4 [000009d400 - 0000100000] BIOS reserved ==> [000009d400 - 0000100000]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #5 [00019e1000 - 00019e1280] BRK ==> [00019e1000 - 00019e1280]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Bootmem setup node 1 0000000040000000-000000007fff0000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] NODE_DATA [0000000040000000 - 0000000040004fff]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] bootmap [0000000040005000 - 000000004000cfff] pages 8
Mar 23 10:44:20 opt2 kernel: [ 0.000000] (7 early reservations) ==> bootmem [0040000000 - 007fff0000]
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #2 [0001000000 - 00019e0ccc] TEXT DATA BSS
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #3 [0037957000 - 0037fefbb8] RAMDISK
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #4 [000009d400 - 0000100000] BIOS reserved
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #5 [00019e1000 - 00019e1280] BRK
Mar 23 10:44:20 opt2 kernel: [ 0.000000] #6 [0000010000 - 0000012000] PGTABLE
Mar 23 10:44:20 opt2 kernel: [ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780
Mar 23 10:44:20 opt2 kernel: [ 0.000000] [ffffea0000000000-ffffea0000dfffff] PMD -> [ffff880001e00000-ffff880002bfffff] on node 0
Mar 23 10:44:20 opt2 kernel: [ 0.000000] [ffffea0000e00000-ffffea0001bfffff] PMD -> [ffff880040200000-ffff880040ffffff] on node 1
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Zone PFN ranges:
Mar 23 10:44:20 opt2 kernel: [ 0.000000] DMA 0x00000010 -> 0x00001000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] DMA32 0x00001000 -> 0x00100000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Normal 0x00100000 -> 0x00100000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Movable zone start PFN for each node
Mar 23 10:44:20 opt2 kernel: [ 0.000000] early_node_map[3] active PFN ranges
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 0: 0x00000010 -> 0x0000009f
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 0: 0x00000100 -> 0x00040000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] 1: 0x00040000 -> 0x0007fff0
Mar 23 10:44:20 opt2 kernel: [ 0.000000] On node 0 totalpages: 262031
Mar 23 10:44:20 opt2 kernel: [ 0.000000] DMA zone: 56 pages used for memmap
Mar 23 10:44:20 opt2 kernel: [ 0.000000] DMA zone: 103 pages reserved
Mar 23 10:44:20 opt2 kernel: [ 0.000000] DMA zone: 3824 pages, LIFO batch:0
Mar 23 10:44:20 opt2 kernel: [ 0.000000] DMA32 zone: 3528 pages used for memmap
Mar 23 10:44:20 opt2 kernel: [ 0.000000] DMA32 zone: 254520 pages, LIFO batch:31
Mar 23 10:44:20 opt2 kernel: [ 0.000000] On node 1 totalpages: 262128
Mar 23 10:44:20 opt2 kernel: [ 0.000000] DMA32 zone: 3584 pages used for memmap
Mar 23 10:44:20 opt2 kernel: [ 0.000000] DMA32 zone: 258544 pages, LIFO batch:31
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: PM-Timer IO Port: 0x5008
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
Mar 23 10:44:20 opt2 kernel: [ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfebff000] gsi_base[24])
Mar 23 10:44:20 opt2 kernel: [ 0.000000] IOAPIC[1]: apic_id 3, version 17, address 0xfebff000, GSI 24-27
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfebfe000] gsi_base[28])
Mar 23 10:44:20 opt2 kernel: [ 0.000000] IOAPIC[2]: apic_id 4, version 17, address 0xfebfe000, GSI 28-31
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: IRQ0 used by override.
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: IRQ2 used by override.
Mar 23 10:44:20 opt2 kernel: [ 0.000000] ACPI: IRQ9 used by override.
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Using ACPI (MADT) for SMP configuration information
Mar 23 10:44:20 opt2 kernel: [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
Mar 23 10:44:20 opt2 kernel: [ 0.000000] nr_irqs_gsi: 32
Mar 23 10:44:20 opt2 kernel: [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:7f7c0000)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:2 nr_node_ids:2
Mar 23 10:44:20 opt2 kernel: [ 0.000000] PERCPU: Remapped at ffffc90000000000 with large pages, static data 90720 bytes
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Built 2 zonelists in Node order, mobility grouping on. Total pages: 516888
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Policy zone: DMA32
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.31-14-server root=UUID=17f0eb6b-217b-440e-8289-6162ed85da7f ro quiet splash
Mar 23 10:44:20 opt2 kernel: [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Initializing CPU#0
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Checking aperture...
Mar 23 10:44:20 opt2 kernel: [ 0.000000] No AGP bridge found
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Node 0: aperture @ 7b5e000000 size 32 MB
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Aperture beyond 4GB. Ignoring.
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Memory: 2050640k/2097088k available (5303k kernel code, 452k absent, 45996k reserved, 3013k data, 660k init)
Mar 23 10:44:20 opt2 kernel: [ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=2
Mar 23 10:44:20 opt2 kernel: [ 0.000000] NR_IRQS:4352 nr_irqs:512
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Fast TSC calibration using PIT
Mar 23 10:44:20 opt2 kernel: [ 0.000000] Detected 1394.256 MHz processor.
Mar 23 10:44:20 opt2 kernel: [ 0.000016] spurious 8259A interrupt: IRQ7.
Mar 23 10:44:20 opt2 kernel: [ 0.003059] Console: colour VGA+ 80x25
Mar 23 10:44:20 opt2 kernel: [ 0.003063] console [tty0] enabled
Mar 23 10:44:20 opt2 kernel: [ 0.010000] allocated 20971520 bytes of page_cgroup
Mar 23 10:44:20 opt2 kernel: [ 0.010000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
Mar 23 10:44:20 opt2 kernel: [ 0.010011] Calibrating delay loop (skipped), value calculated using timer frequency.. 2788.51 BogoMIPS (lpj=13942560)
Mar 23 10:44:20 opt2 kernel: [ 0.010065] Security Framework initialized
Mar 23 10:44:20 opt2 kernel: [ 0.010104] AppArmor: AppArmor initialized
Mar 23 10:44:20 opt2 kernel: [ 0.010416] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mar 23 10:44:20 opt2 kernel: [ 0.013040] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mar 23 10:44:20 opt2 kernel: [ 0.014084] Mount-cache hash table entries: 256
Mar 23 10:44:20 opt2 kernel: [ 0.014326] Initializing cgroup subsys ns
Mar 23 10:44:20 opt2 kernel: [ 0.014332] Initializing cgroup subsys cpuacct
Mar 23 10:44:20 opt2 kernel: [ 0.014339] Initializing cgroup subsys memory
Mar 23 10:44:20 opt2 kernel: [ 0.014357] Initializing cgroup subsys freezer
Mar 23 10:44:20 opt2 kernel: [ 0.014360] Initializing cgroup subsys net_cls
Mar 23 10:44:20 opt2 kernel: [ 0.014388] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Mar 23 10:44:20 opt2 kernel: [ 0.014392] CPU: L2 Cache: 1024K (64 bytes/line)
Mar 23 10:44:20 opt2 kernel: [ 0.014397] CPU 0/0x0 -> Node 0
Mar 23 10:44:20 opt2 kernel: [ 0.014400] tseg: 0000000000
Mar 23 10:44:20 opt2 kernel: [ 0.014427] mce: CPU supports 5 MCE banks
Mar 23 10:44:20 opt2 kernel: [ 0.014444] Performance Counters: AMD PMU driver.
Mar 23 10:44:20 opt2 kernel: [ 0.014451] ... version: 0
Mar 23 10:44:20 opt2 kernel: [ 0.014453] ... bit width: 48
Mar 23 10:44:20 opt2 kernel: [ 0.014456] ... generic counters: 4
Mar 23 10:44:20 opt2 kernel: [ 0.014458] ... value mask: 0000ffffffffffff
Mar 23 10:44:20 opt2 kernel: [ 0.014461] ... max period: 00007fffffffffff
Mar 23 10:44:20 opt2 kernel: [ 0.014463] ... fixed-purpose counters: 0
Mar 23 10:44:20 opt2 kernel: [ 0.014466] ... counter mask: 000000000000000f
Mar 23 10:44:20 opt2 kernel: [ 0.017015] ACPI: Core revision 20090521
Mar 23 10:44:20 opt2 kernel: [ 0.025477] Setting APIC routing to flat
Mar 23 10:44:20 opt2 kernel: [ 0.025812] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
Mar 23 10:44:20 opt2 kernel: [ 0.126106] CPU0: AMD Opteron(tm) Processor 240 stepping 01
Mar 23 10:44:20 opt2 kernel: [ 0.130000] Booting processor 1 APIC 0x1 ip 0x6000
Mar 23 10:44:20 opt2 kernel: [ 0.010000] Initializing CPU#1
Mar 23 10:44:20 opt2 kernel: [ 0.010000] Calibrating delay using timer specific routine.. 2788.28 BogoMIPS (lpj=13941417)
Mar 23 10:44:20 opt2 kernel: [ 0.010000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Mar 23 10:44:20 opt2 kernel: [ 0.010000] CPU: L2 Cache: 1024K (64 bytes/line)
Mar 23 10:44:20 opt2 kernel: [ 0.010000] CPU 1/0x1 -> Node 1
Mar 23 10:44:20 opt2 kernel: [ 0.010000] mce: CPU supports 5 MCE banks
Mar 23 10:44:20 opt2 kernel: [ 0.010000] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
Mar 23 10:44:20 opt2 kernel: [ 0.280837] CPU1: AMD Opteron(tm) Processor 240 stepping 01
Mar 23 10:44:20 opt2 kernel: [ 0.280857] Brought up 2 CPUs
Mar 23 10:44:20 opt2 kernel: [ 0.280860] Total of 2 processors activated (5576.79 BogoMIPS).
Mar 23 10:44:20 opt2 kernel: [ 0.280943] CPU0 attaching sched-domain:
Mar 23 10:44:20 opt2 kernel: [ 0.280948] domain 0: span 0-1 level NODE
Mar 23 10:44:20 opt2 kernel: [ 0.280952] groups: 0 1
Mar 23 10:44:20 opt2 kernel: [ 0.280961] CPU1 attaching sched-domain:
Mar 23 10:44:20 opt2 kernel: [ 0.280964] domain 0: span 0-1 level NODE
Mar 23 10:44:20 opt2 kernel: [ 0.280967] groups: 1 0
Mar 23 10:44:20 opt2 kernel: [ 0.281079] Booting paravirtualized kernel on bare hardware
Mar 23 10:44:20 opt2 kernel: [ 0.281079] regulator: core version 0.5
Mar 23 10:44:20 opt2 kernel: [ 0.281079] Time: 16:43:59 Date: 03/23/10
Mar 23 10:44:20 opt2 kernel: [ 0.281079] NET: Registered protocol family 16
Mar 23 10:44:20 opt2 kernel: [ 0.281079] node 0 link 0: io port [0, ffffff]
Mar 23 10:44:20 opt2 kernel: [ 0.281079] TOM: 0000000080000000 aka 2048M
Mar 23 10:44:20 opt2 kernel: [ 0.281079] node 0 link 0: mmio [a0000, bffff]
Mar 23 10:44:20 opt2 kernel: [ 0.281079] node 0 link 0: mmio [80000000, ffffffff]
Mar 23 10:44:20 opt2 kernel: [ 0.281079] bus: [00,ff] on node 0 link 0
Mar 23 10:44:20 opt2 kernel: [ 0.281079] bus: 00 index 0 io port: [0, ffff]
Mar 23 10:44:20 opt2 kernel: [ 0.281079] bus: 00 index 1 mmio: [a0000, bffff]
Mar 23 10:44:20 opt2 kernel: [ 0.281079] bus: 00 index 2 mmio: [80000000, fcffffffff]
Mar 23 10:44:20 opt2 kernel: [ 0.281079] ACPI: bus type pci registered
Mar 23 10:44:20 opt2 kernel: [ 0.281079] PCI: Using configuration type 1 for base access
Mar 23 10:44:20 opt2 kernel: [ 0.281810] bio: create slab <bio-0> at 0
Mar 23 10:44:20 opt2 kernel: [ 0.281810] ACPI: EC: Look up EC in DSDT
Mar 23 10:44:20 opt2 kernel: [ 0.299084] ACPI: Interpreter enabled
Mar 23 10:44:20 opt2 kernel: [ 0.299089] ACPI: (supports S0 S1 S4 S5)
Mar 23 10:44:20 opt2 kernel: [ 0.299121] ACPI: Using IOAPIC for interrupt routing
Mar 23 10:44:20 opt2 kernel: [ 0.308529] ACPI: No dock devices found.
Mar 23 10:44:20 opt2 kernel: [ 0.308699] ACPI: PCI Root Bridge [PCI0] (0000:00)
Mar 23 10:44:20 opt2 kernel: [ 0.308903] pci 0000:00:07.1: reg 20 io port: [0xffa0-0xffaf]
Mar 23 10:44:20 opt2 kernel: [ 0.308938] pci 0000:00:07.2: reg 10 io port: [0xcc00-0xcc1f]
Mar 23 10:44:20 opt2 kernel: [ 0.309094] pci 0000:00:0a.1: reg 10 64bit mmio: [0xfebff000-0xfebfffff]
Mar 23 10:44:20 opt2 kernel: [ 0.309169] pci 0000:00:0b.1: reg 10 64bit mmio: [0xfebfe000-0xfebfefff]
Mar 23 10:44:20 opt2 kernel: [ 0.309393] pci 0000:03:00.0: reg 10 32bit mmio: [0xfeafc000-0xfeafcfff]
Mar 23 10:44:20 opt2 kernel: [ 0.309453] pci 0000:03:00.1: reg 10 32bit mmio: [0xfeafd000-0xfeafdfff]
Mar 23 10:44:20 opt2 kernel: [ 0.309538] pci 0000:03:05.0: reg 10 io port: [0xac00-0xac07]
Mar 23 10:44:20 opt2 kernel: [ 0.309546] pci 0000:03:05.0: reg 14 io port: [0xa480-0xa483]
Mar 23 10:44:20 opt2 kernel: [ 0.309555] pci 0000:03:05.0: reg 18 io port: [0xa400-0xa407]
Mar 23 10:44:20 opt2 kernel: [ 0.309564] pci 0000:03:05.0: reg 1c io port: [0xa080-0xa083]
Mar 23 10:44:20 opt2 kernel: [ 0.309573] pci 0000:03:05.0: reg 20 io port: [0xa000-0xa00f]
Mar 23 10:44:20 opt2 kernel: [ 0.309582] pci 0000:03:05.0: reg 24 32bit mmio: [0xfeafec00-0xfeafefff]
Mar 23 10:44:20 opt2 kernel: [ 0.309591] pci 0000:03:05.0: reg 30 32bit mmio: [0xfea00000-0xfea7ffff]
Mar 23 10:44:20 opt2 kernel: [ 0.309613] pci 0000:03:05.0: supports D1 D2
Mar 23 10:44:20 opt2 kernel: [ 0.309654] pci 0000:03:06.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
Mar 23 10:44:20 opt2 kernel: [ 0.309664] pci 0000:03:06.0: reg 14 io port: [0xa800-0xa8ff]
Mar 23 10:44:20 opt2 kernel: [ 0.309673] pci 0000:03:06.0: reg 18 32bit mmio: [0xfeaff000-0xfeafffff]
Mar 23 10:44:20 opt2 kernel: [ 0.309699] pci 0000:03:06.0: reg 30 32bit mmio: [0xfeac0000-0xfeadffff]
Mar 23 10:44:20 opt2 kernel: [ 0.309722] pci 0000:03:06.0: supports D1 D2
Mar 23 10:44:20 opt2 kernel: [ 0.309762] pci 0000:03:08.0: reg 10 32bit mmio: [0xfeafb000-0xfeafbfff]
Mar 23 10:44:20 opt2 kernel: [ 0.309771] pci 0000:03:08.0: reg 14 io port: [0x9c00-0x9c3f]
Mar 23 10:44:20 opt2 kernel: [ 0.309780] pci 0000:03:08.0: reg 18 32bit mmio: [0xfea80000-0xfea9ffff]
Mar 23 10:44:20 opt2 kernel: [ 0.309821] pci 0000:03:08.0: supports D1 D2
Mar 23 10:44:20 opt2 kernel: [ 0.309824] pci 0000:03:08.0: PME# supported from D0 D1 D2 D3hot D3cold
Mar 23 10:44:20 opt2 kernel: [ 0.309831] pci 0000:03:08.0: PME# disabled
Mar 23 10:44:20 opt2 kernel: [ 0.309874] pci 0000:00:06.0: bridge io port: [0x9000-0xafff]
Mar 23 10:44:20 opt2 kernel: [ 0.309880] pci 0000:00:06.0: bridge 32bit mmio: [0xfc900000-0xfeafffff]
Mar 23 10:44:20 opt2 kernel: [ 0.309886] pci 0000:00:06.0: bridge 32bit mmio pref: [0xff500000-0xff5fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.309915] pci 0000:02:02.0: reg 10 io port: [0x8c00-0x8c7f]
Mar 23 10:44:20 opt2 kernel: [ 0.309924] pci 0000:02:02.0: reg 18 io port: [0x8800-0x88ff]
Mar 23 10:44:20 opt2 kernel: [ 0.309930] pci 0000:02:02.0: reg 1c 32bit mmio: [0xfc8ff000-0xfc8fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.309937] pci 0000:02:02.0: reg 20 32bit mmio: [0xfc8c0000-0xfc8dffff]
Mar 23 10:44:20 opt2 kernel: [ 0.309946] pci 0000:02:02.0: reg 30 32bit mmio: [0xfc8f0000-0xfc8f7fff]
Mar 23 10:44:20 opt2 kernel: [ 0.309959] pci 0000:02:02.0: supports D1
Mar 23 10:44:20 opt2 kernel: [ 0.310011] pci 0000:02:09.0: reg 10 64bit mmio: [0xfc890000-0xfc89ffff]
Mar 23 10:44:20 opt2 kernel: [ 0.310021] pci 0000:02:09.0: reg 18 64bit mmio: [0xfc880000-0xfc88ffff]
Mar 23 10:44:20 opt2 kernel: [ 0.310033] pci 0000:02:09.0: reg 30 32bit mmio: [0xfc870000-0xfc87ffff]
Mar 23 10:44:20 opt2 kernel: [ 0.310052] pci 0000:02:09.0: PME# supported from D3hot D3cold
Mar 23 10:44:20 opt2 kernel: [ 0.310057] pci 0000:02:09.0: PME# disabled
Mar 23 10:44:20 opt2 kernel: [ 0.310094] pci 0000:02:09.1: reg 10 64bit mmio: [0xfc8e0000-0xfc8effff]
Mar 23 10:44:20 opt2 kernel: [ 0.310104] pci 0000:02:09.1: reg 18 64bit mmio: [0xfc8b0000-0xfc8bffff]
Mar 23 10:44:20 opt2 kernel: [ 0.310116] pci 0000:02:09.1: reg 30 32bit mmio: [0xfc8a0000-0xfc8affff]
Mar 23 10:44:20 opt2 kernel: [ 0.310135] pci 0000:02:09.1: PME# supported from D3hot D3cold
Mar 23 10:44:20 opt2 kernel: [ 0.310140] pci 0000:02:09.1: PME# disabled
Mar 23 10:44:20 opt2 kernel: [ 0.310172] pci 0000:00:0a.0: bridge io port: [0x8000-0x8fff]
Mar 23 10:44:20 opt2 kernel: [ 0.310177] pci 0000:00:0a.0: bridge 32bit mmio: [0xfc700000-0xfc8fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.310183] pci 0000:00:0a.0: bridge 64bit mmio pref: [0xff400000-0xff4fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.310212] pci 0000:01:03.0: reg 10 io port: [0x7c00-0x7c7f]
Mar 23 10:44:20 opt2 kernel: [ 0.310221] pci 0000:01:03.0: reg 18 io port: [0x7800-0x78ff]
Mar 23 10:44:20 opt2 kernel: [ 0.310227] pci 0000:01:03.0: reg 1c 32bit mmio: [0xfc6ff000-0xfc6fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.310234] pci 0000:01:03.0: reg 20 32bit mmio: [0xfc6c0000-0xfc6dffff]
Mar 23 10:44:20 opt2 kernel: [ 0.310243] pci 0000:01:03.0: reg 30 32bit mmio: [0xfc6f0000-0xfc6f7fff]
Mar 23 10:44:20 opt2 kernel: [ 0.310256] pci 0000:01:03.0: supports D1
Mar 23 10:44:20 opt2 kernel: [ 0.310286] pci 0000:00:0b.0: bridge io port: [0x7000-0x7fff]
Mar 23 10:44:20 opt2 kernel: [ 0.310291] pci 0000:00:0b.0: bridge 32bit mmio: [0xfc600000-0xfc6fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.310297] pci 0000:00:0b.0: bridge 64bit mmio pref: [0xff300000-0xff3fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.310315] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Mar 23 10:44:20 opt2 kernel: [ 0.310396] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Mar 23 10:44:20 opt2 kernel: [ 0.310515] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLA._PRT]
Mar 23 10:44:20 opt2 kernel: [ 0.310655] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLB._PRT]
Mar 23 10:44:20 opt2 kernel: [ 0.313823] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
Mar 23 10:44:20 opt2 kernel: [ 0.313976] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Mar 23 10:44:20 opt2 kernel: [ 0.314126] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Mar 23 10:44:20 opt2 kernel: [ 0.314276] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Mar 23 10:44:20 opt2 kernel: [ 0.314524] SCSI subsystem initialized
Mar 23 10:44:20 opt2 kernel: [ 0.314562] libata version 3.00 loaded.
Mar 23 10:44:20 opt2 kernel: [ 0.314562] usbcore: registered new interface driver usbfs
Mar 23 10:44:20 opt2 kernel: [ 0.314562] usbcore: registered new interface driver hub
Mar 23 10:44:20 opt2 kernel: [ 0.314562] usbcore: registered new device driver usb
Mar 23 10:44:20 opt2 kernel: [ 0.314562] ACPI: WMI: Mapper loaded
Mar 23 10:44:20 opt2 kernel: [ 0.314562] PCI: Using ACPI for IRQ routing
Mar 23 10:44:20 opt2 kernel: [ 0.340012] Bluetooth: Core ver 2.15
Mar 23 10:44:20 opt2 kernel: [ 0.340040] NET: Registered protocol family 31
Mar 23 10:44:20 opt2 kernel: [ 0.340040] Bluetooth: HCI device and connection manager initialized
Mar 23 10:44:20 opt2 kernel: [ 0.340040] Bluetooth: HCI socket layer initialized
Mar 23 10:44:20 opt2 kernel: [ 0.340040] NetLabel: Initializing
Mar 23 10:44:20 opt2 kernel: [ 0.340040] NetLabel: domain hash size = 128
Mar 23 10:44:20 opt2 kernel: [ 0.340040] NetLabel: protocols = UNLABELED CIPSOv4
Mar 23 10:44:20 opt2 kernel: [ 0.340058] NetLabel: unlabeled traffic allowed by default
Mar 23 10:44:20 opt2 kernel: [ 0.370022] pnp: PnP ACPI init
Mar 23 10:44:20 opt2 kernel: [ 0.370048] ACPI: bus type pnp registered
Mar 23 10:44:20 opt2 kernel: [ 0.376168] pnp: PnP ACPI: found 14 devices
Mar 23 10:44:20 opt2 kernel: [ 0.376171] ACPI: ACPI bus type pnp unregistered
Mar 23 10:44:20 opt2 kernel: [ 0.376191] system 00:09: ioport range 0x680-0x6ff has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376195] system 00:09: ioport range 0x295-0x296 has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376200] system 00:09: ioport range 0x778-0x77f has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376204] system 00:09: ioport range 0xb78-0xb7f has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376208] system 00:09: ioport range 0xf78-0xf7f has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376217] system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376222] system 00:0a: ioport range 0x5000-0x50bf has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376227] system 00:0a: ioport range 0x50e0-0x50ff has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376231] system 00:0a: ioport range 0x50c0-0x50df has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376236] system 00:0a: ioport range 0xde00-0xde7f has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376241] system 00:0a: ioport range 0xde80-0xdeff has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376250] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376255] system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376260] system 00:0c: iomem range 0xfff80000-0xffffffff has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376268] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376273] system 00:0d: iomem range 0xc0000-0xdffff has been reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376278] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
Mar 23 10:44:20 opt2 kernel: [ 0.376283] system 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
Mar 23 10:44:20 opt2 kernel: [ 0.381046] AppArmor: AppArmor Filesystem Enabled
Mar 23 10:44:20 opt2 kernel: [ 0.381100] pci 0000:00:06.0: PCI bridge, secondary bus 0000:03
Mar 23 10:44:20 opt2 kernel: [ 0.381105] pci 0000:00:06.0: IO window: 0x9000-0xafff
Mar 23 10:44:20 opt2 kernel: [ 0.381112] pci 0000:00:06.0: MEM window: 0xfc900000-0xfeafffff
Mar 23 10:44:20 opt2 kernel: [ 0.381119] pci 0000:00:06.0: PREFETCH window: 0xff500000-0xff5fffff
Mar 23 10:44:20 opt2 kernel: [ 0.381125] pci 0000:00:0a.0: PCI bridge, secondary bus 0000:02
Mar 23 10:44:20 opt2 kernel: [ 0.381129] pci 0000:00:0a.0: IO window: 0x8000-0x8fff
Mar 23 10:44:20 opt2 kernel: [ 0.381135] pci 0000:00:0a.0: MEM window: 0xfc700000-0xfc8fffff
Mar 23 10:44:20 opt2 kernel: [ 0.381140] pci 0000:00:0a.0: PREFETCH window: 0x000000ff400000-0x000000ff4fffff
Mar 23 10:44:20 opt2 kernel: [ 0.381146] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:01
Mar 23 10:44:20 opt2 kernel: [ 0.381150] pci 0000:00:0b.0: IO window: 0x7000-0x7fff
Mar 23 10:44:20 opt2 kernel: [ 0.381155] pci 0000:00:0b.0: MEM window: 0xfc600000-0xfc6fffff
Mar 23 10:44:20 opt2 kernel: [ 0.381160] pci 0000:00:0b.0: PREFETCH window: 0x000000ff300000-0x000000ff3fffff
Mar 23 10:44:20 opt2 kernel: [ 0.381184] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
Mar 23 10:44:20 opt2 kernel: [ 0.381188] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
Mar 23 10:44:20 opt2 kernel: [ 0.381193] pci_bus 0000:03: resource 0 io: [0x9000-0xafff]
Mar 23 10:44:20 opt2 kernel: [ 0.381197] pci_bus 0000:03: resource 1 mem: [0xfc900000-0xfeafffff]
Mar 23 10:44:20 opt2 kernel: [ 0.381201] pci_bus 0000:03: resource 2 pref mem [0xff500000-0xff5fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.381206] pci_bus 0000:02: resource 0 io: [0x8000-0x8fff]
Mar 23 10:44:20 opt2 kernel: [ 0.381210] pci_bus 0000:02: resource 1 mem: [0xfc700000-0xfc8fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.381214] pci_bus 0000:02: resource 2 pref mem [0xff400000-0xff4fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.381219] pci_bus 0000:01: resource 0 io: [0x7000-0x7fff]
Mar 23 10:44:20 opt2 kernel: [ 0.381223] pci_bus 0000:01: resource 1 mem: [0xfc600000-0xfc6fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.381227] pci_bus 0000:01: resource 2 pref mem [0xff300000-0xff3fffff]
Mar 23 10:44:20 opt2 kernel: [ 0.381288] NET: Registered protocol family 2
Mar 23 10:44:20 opt2 kernel: [ 0.381520] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
Mar 23 10:44:20 opt2 kernel: [ 0.383643] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
Mar 23 10:44:20 opt2 kernel: [ 0.388501] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Mar 23 10:44:20 opt2 kernel: [ 0.389635] TCP: Hash tables configured (established 262144 bind 65536)
Mar 23 10:44:20 opt2 kernel: [ 0.389639] TCP reno registered
Mar 23 10:44:20 opt2 kernel: [ 0.389795] NET: Registered protocol family 1
Mar 23 10:44:20 opt2 kernel: [ 0.389929] Trying to unpack rootfs image as initramfs...
Mar 23 10:44:20 opt2 kernel: [ 0.390032] Switched to high resolution mode on CPU 0
Mar 23 10:44:20 opt2 kernel: [ 0.390783] Switched to high resolution mode on CPU 1
Mar 23 10:44:20 opt2 kernel: [ 0.658081] Freeing initrd memory: 6754k freed
Mar 23 10:44:20 opt2 kernel: [ 0.667622] Scanning for low memory corruption every 60 seconds
Mar 23 10:44:20 opt2 kernel: [ 0.667863] audit: initializing netlink socket (disabled)
Mar 23 10:44:20 opt2 kernel: [ 0.667886] type=2000 audit(1269362639.660:1): initialized
Mar 23 10:44:20 opt2 kernel: [ 0.681795] HugeTLB registered 2 MB page size, pre-allocated 0 pages
Mar 23 10:44:20 opt2 kernel: [ 0.684066] VFS: Disk quotas dquot_6.5.2
Mar 23 10:44:20 opt2 kernel: [ 0.684155] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Mar 23 10:44:20 opt2 kernel: [ 0.685139] fuse init (API version 7.12)
Mar 23 10:44:20 opt2 kernel: [ 0.685262] msgmni has been set to 4018
Mar 23 10:44:20 opt2 kernel: [ 0.685657] alg: No test for stdrng (krng)
Mar 23 10:44:20 opt2 kernel: [ 0.685697] io scheduler noop registered
Mar 23 10:44:20 opt2 kernel: [ 0.685700] io scheduler anticipatory registered
Mar 23 10:44:20 opt2 kernel: [ 0.685703] io scheduler deadline registered (default)
Mar 23 10:44:20 opt2 kernel: [ 0.685764] io scheduler cfq registered
Mar 23 10:44:20 opt2 kernel: [ 0.685789] boot interrupts on PCI device 0x1022:0x746b already disabled
Mar 23 10:44:20 opt2 kernel: [ 0.685795] pci 0000:00:0a.0: MSI quirk detected; subordinate MSI disabled
Mar 23 10:44:20 opt2 kernel: [ 0.685802] disabled boot interrupts on PCI device 0x1022:0x7450
Mar 23 10:44:20 opt2 kernel: [ 0.685806] pci 0000:00:0a.0: AMD8131 rev 12 detected; disabling PCI-X MMRBC
Mar 23 10:44:20 opt2 kernel: [ 0.685813] pci 0000:00:0b.0: MSI quirk detected; subordinate MSI disabled
Mar 23 10:44:20 opt2 kernel: [ 0.685818] disabled boot interrupts on PCI device 0x1022:0x7450
Mar 23 10:44:20 opt2 kernel: [ 0.685822] pci 0000:00:0b.0: AMD8131 rev 12 detected; disabling PCI-X MMRBC
Mar 23 10:44:20 opt2 kernel: [ 0.740025] pci 0000:03:06.0: Boot video device
Mar 23 10:44:20 opt2 kernel: [ 0.740042] pci 0000:03:08.0: Firmware left e100 interrupts enabled; disabling
Mar 23 10:44:20 opt2 kernel: [ 0.740403] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Mar 23 10:44:20 opt2 kernel: [ 0.740441] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
Mar 23 10:44:20 opt2 kernel: [ 0.740622] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
Mar 23 10:44:20 opt2 kernel: [ 0.740629] ACPI: Power Button [PWRF]
Mar 23 10:44:20 opt2 kernel: [ 0.740711] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
Mar 23 10:44:20 opt2 kernel: [ 0.740720] ACPI: Power Button [PWRB]
Mar 23 10:44:20 opt2 kernel: [ 0.740977] ACPI: processor limited to max C-state 1
Mar 23 10:44:20 opt2 kernel: [ 0.741018] processor LNXCPU:00: registered as cooling_device0
Mar 23 10:44:20 opt2 kernel: [ 0.741024] ACPI: Processor [CPU0] (supports 8 throttling states)
Mar 23 10:44:20 opt2 kernel: [ 0.741088] processor LNXCPU:01: registered as cooling_device1
Mar 23 10:44:20 opt2 kernel: [ 0.745609] hpet_acpi_add: no address or irqs in _CRS
Mar 23 10:44:20 opt2 kernel: [ 0.745626] Linux agpgart interface v0.103
Mar 23 10:44:20 opt2 kernel: [ 0.745642] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
Mar 23 10:44:20 opt2 kernel: [ 0.745773] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Mar 23 10:44:20 opt2 kernel: [ 0.745883] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Mar 23 10:44:20 opt2 kernel: [ 0.746177] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Mar 23 10:44:20 opt2 kernel: [ 0.746328] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Mar 23 10:44:20 opt2 kernel: [ 0.747884] brd: module loaded
Mar 23 10:44:20 opt2 kernel: [ 0.748529] loop: module loaded
Mar 23 10:44:20 opt2 kernel: [ 0.748651] input: Macintosh mouse button emulation as /devices/virtual/input/input2
Mar 23 10:44:20 opt2 kernel: [ 0.748917] sata_promise 0000:02:02.0: version 2.12
Mar 23 10:44:20 opt2 kernel: [ 0.748937] alloc irq_desc for 26 on node 0
Mar 23 10:44:20 opt2 kernel: [ 0.748940] alloc kstat_irqs on node 0
Mar 23 10:44:20 opt2 kernel: [ 0.748954] sata_promise 0000:02:02.0: PCI INT A -> GSI 26 (level, low) -> IRQ 26
Mar 23 10:44:20 opt2 kernel: [ 0.749173] scsi0 : sata_promise
Mar 23 10:44:20 opt2 kernel: [ 0.749330] scsi1 : sata_promise
Mar 23 10:44:20 opt2 kernel: [ 0.749421] scsi2 : sata_promise
Mar 23 10:44:20 opt2 kernel: [ 0.749511] scsi3 : sata_promise
Mar 23 10:44:20 opt2 kernel: [ 0.749561] ata1: SATA max UDMA/133 mmio m4096@0xfc8ff000 ata 0xfc8ff380 irq 26
Mar 23 10:44:20 opt2 kernel: [ 0.749566] ata2: SATA max UDMA/133 mmio m4096@0xfc8ff000 ata 0xfc8ff280 irq 26
Mar 23 10:44:20 opt2 kernel: [ 0.749570] ata3: SATA max UDMA/133 mmio m4096@0xfc8ff000 ata 0xfc8ff200 irq 26
Mar 23 10:44:20 opt2 kernel: [ 0.749575] ata4: SATA max UDMA/133 mmio m4096@0xfc8ff000 ata 0xfc8ff300 irq 26
Mar 23 10:44:20 opt2 kernel: [ 0.749663] alloc irq_desc for 28 on node 0
Mar 23 10:44:20 opt2 kernel: [ 0.749666] alloc kstat_irqs on node 0
Mar 23 10:44:20 opt2 kernel: [ 0.749672] sata_promise 0000:01:03.0: PCI INT A -> GSI 28 (level, low) -> IRQ 28
Mar 23 10:44:20 opt2 kernel: [ 0.749851] scsi4 : sata_promise
Mar 23 10:44:20 opt2 kernel: [ 0.749980] scsi5 : sata_promise
Mar 23 10:44:20 opt2 kernel: [ 0.750110] scsi6 : sata_promise
Mar 23 10:44:20 opt2 kernel: [ 0.750210] scsi7 : sata_promise
Mar 23 10:44:20 opt2 kernel: [ 0.750257] ata5: SATA max UDMA/133 mmio m4096@0xfc6ff000 ata 0xfc6ff380 irq 28
Mar 23 10:44:20 opt2 kernel: [ 0.750261] ata6: SATA max UDMA/133 mmio m4096@0xfc6ff000 ata 0xfc6ff280 irq 28
Mar 23 10:44:20 opt2 kernel: [ 0.750266] ata7: SATA max UDMA/133 mmio m4096@0xfc6ff000 ata 0xfc6ff200 irq 28
Mar 23 10:44:20 opt2 kernel: [ 0.750270] ata8: SATA max UDMA/133 mmio m4096@0xfc6ff000 ata 0xfc6ff300 irq 28
Mar 23 10:44:20 opt2 kernel: [ 0.750497] sata_sil 0000:03:05.0: version 2.4
Mar 23 10:44:20 opt2 kernel: [ 0.750573] alloc irq_desc for 19 on node 0
Mar 23 10:44:20 opt2 kernel: [ 0.750576] alloc kstat_irqs on node 0
Mar 23 10:44:20 opt2 kernel: [ 0.750582] sata_sil 0000:03:05.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
Mar 23 10:44:20 opt2 kernel: [ 0.750604] sata_sil 0000:03:05.0: Applying R_ERR on DMA activate FIS errata fix
Mar 23 10:44:20 opt2 kernel: [ 0.750728] scsi8 : sata_sil
Mar 23 10:44:20 opt2 kernel: [ 0.750835] scsi9 : sata_sil
Mar 23 10:44:20 opt2 kernel: [ 0.750933] scsi10 : sata_sil
Mar 23 10:44:20 opt2 kernel: [ 0.751028] scsi11 : sata_sil
Mar 23 10:44:20 opt2 kernel: [ 0.751082] ata9: SATA max UDMA/100 mmio m1024@0xfeafec00 tf 0xfeafec80 irq 19
Mar 23 10:44:20 opt2 kernel: [ 0.751087] ata10: SATA max UDMA/100 mmio m1024@0xfeafec00 tf 0xfeafecc0 irq 19
Mar 23 10:44:20 opt2 kernel: [ 0.751092] ata11: SATA max UDMA/100 mmio m1024@0xfeafec00 tf 0xfeafee80 irq 19
Mar 23 10:44:20 opt2 kernel: [ 0.751097] ata12: SATA max UDMA/100 mmio m1024@0xfeafec00 tf 0xfeafeec0 irq 19
Mar 23 10:44:20 opt2 kernel: [ 0.751615] pata_amd 0000:00:07.1: version 0.4.1
Mar 23 10:44:20 opt2 kernel: [ 0.751848] scsi12 : pata_amd
Mar 23 10:44:20 opt2 kernel: [ 0.751947] scsi13 : pata_amd
Mar 23 10:44:20 opt2 kernel: [ 0.753001] ata13: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
Mar 23 10:44:20 opt2 kernel: [ 0.753005] ata14: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
Mar 23 10:44:20 opt2 kernel: [ 0.754185] Fixed MDIO Bus: probed
Mar 23 10:44:20 opt2 kernel: [ 0.754242] PPP generic driver version 2.4.2
Mar 23 10:44:20 opt2 kernel: [ 0.754396] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Mar 23 10:44:20 opt2 kernel: [ 0.754423] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Mar 23 10:44:20 opt2 kernel: [ 0.754541] ohci_hcd 0000:03:00.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
Mar 23 10:44:20 opt2 kernel: [ 0.754563] ohci_hcd 0000:03:00.0: OHCI Host Controller
Mar 23 10:44:20 opt2 kernel: [ 0.754651] ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
Mar 23 10:44:20 opt2 kernel: [ 0.754676] ohci_hcd 0000:03:00.0: irq 19, io mem 0xfeafc000
Mar 23 10:44:20 opt2 kernel: [ 0.812140] usb usb1: configuration #1 chosen from 1 choice
Mar 23 10:44:20 opt2 kernel: [ 0.812185] hub 1-0:1.0: USB hub found
Mar 23 10:44:20 opt2 kernel: [ 0.812203] hub 1-0:1.0: 3 ports detected
Mar 23 10:44:20 opt2 kernel: [ 0.812349] ohci_hcd 0000:03:00.1: PCI INT D -> GSI 19 (level, low) -> IRQ 19
Mar 23 10:44:20 opt2 kernel: [ 0.812363] ohci_hcd 0000:03:00.1: OHCI Host Controller
Mar 23 10:44:20 opt2 kernel: [ 0.812429] ohci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 2
Mar 23 10:44:20 opt2 kernel: [ 0.812451] ohci_hcd 0000:03:00.1: irq 19, io mem 0xfeafd000
Mar 23 10:44:20 opt2 kernel: [ 0.872104] usb usb2: configuration #1 chosen from 1 choice
Mar 23 10:44:20 opt2 kernel: [ 0.872146] hub 2-0:1.0: USB hub found
Mar 23 10:44:20 opt2 kernel: [ 0.872159] hub 2-0:1.0: 3 ports detected
Mar 23 10:44:20 opt2 kernel: [ 0.872236] uhci_hcd: USB Universal Host Controller Interface driver
Mar 23 10:44:20 opt2 kernel: [ 0.872423] PNP: No PS/2 controller found. Probing ports directly.
Mar 23 10:44:20 opt2 kernel: [ 0.874466] serio: i8042 KBD port at 0x60,0x64 irq 1
Mar 23 10:44:20 opt2 kernel: [ 0.874476] serio: i8042 AUX port at 0x60,0x64 irq 12
Mar 23 10:44:20 opt2 kernel: [ 0.874609] mice: PS/2 mouse device common for all mice
Mar 23 10:44:20 opt2 kernel: [ 0.874748] rtc_cmos 00:02: RTC can wake from S4
Mar 23 10:44:20 opt2 kernel: [ 0.874813] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
Mar 23 10:44:20 opt2 kernel: [ 0.874847] rtc0: alarms up to one year, y3k, 114 bytes nvram
Mar 23 10:44:20 opt2 kernel: [ 0.875044] device-mapper: uevent: version 1.0.3
Mar 23 10:44:20 opt2 kernel: [ 0.875205] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
Mar 23 10:44:20 opt2 kernel: [ 0.875353] device-mapper: multipath: version 1.1.0 loaded
Mar 23 10:44:20 opt2 kernel: [ 0.875359] device-mapper: multipath round-robin: version 1.0.0 loaded
Mar 23 10:44:20 opt2 kernel: [ 0.875694] cpuidle: using governor ladder
Mar 23 10:44:20 opt2 kernel: [ 0.875697] cpuidle: using governor menu
Mar 23 10:44:20 opt2 kernel: [ 0.876366] TCP cubic registered
Mar 23 10:44:20 opt2 kernel: [ 0.876566] NET: Registered protocol family 10
Mar 23 10:44:20 opt2 kernel: [ 0.877256] lo: Disabled Privacy Extensions
Mar 23 10:44:20 opt2 kernel: [ 0.877676] NET: Registered protocol family 17
Mar 23 10:44:20 opt2 kernel: [ 0.877708] Bluetooth: L2CAP ver 2.13
Mar 23 10:44:20 opt2 kernel: [ 0.877711] Bluetooth: L2CAP socket layer initialized
Mar 23 10:44:20 opt2 kernel: [ 0.877716] Bluetooth: SCO (Voice Link) ver 0.6
Mar 23 10:44:20 opt2 kernel: [ 0.877718] Bluetooth: SCO socket layer initialized
Mar 23 10:44:20 opt2 kernel: [ 0.877773] Bluetooth: RFCOMM TTY layer initialized
Mar 23 10:44:20 opt2 kernel: [ 0.877777] Bluetooth: RFCOMM socket layer initialized
Mar 23 10:44:20 opt2 kernel: [ 0.877779] Bluetooth: RFCOMM ver 1.11
Mar 23 10:44:20 opt2 kernel: [ 0.877819] powernow-k8: Power state transitions not supported
Mar 23 10:44:20 opt2 kernel: [ 0.877825] powernow-k8: Power state transitions not supported
Mar 23 10:44:20 opt2 kernel: [ 0.877950] PM: Resume from disk failed.
Mar 23 10:44:20 opt2 kernel: [ 0.877970] registered taskstats version 1
Mar 23 10:44:20 opt2 kernel: [ 0.878212] Magic number: 2:92:743
Mar 23 10:44:20 opt2 kernel: [ 0.878339] rtc_cmos 00:02: setting system clock to 2010-03-23 16:44:00 UTC (1269362640)
Mar 23 10:44:20 opt2 kernel: [ 0.878344] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
Mar 23 10:44:20 opt2 kernel: [ 0.878347] EDD information not available.
Mar 23 10:44:20 opt2 kernel: [ 0.953048] ata13.00: ATA-6: Maxtor 4D040H2, DAH017K0, max UDMA/100
Mar 23 10:44:20 opt2 kernel: [ 0.953052] ata13.00: 80043264 sectors, multi 16: LBA
Mar 23 10:44:20 opt2 kernel: [ 0.953097] ata13.01: ATAPI: SONY DVD RW AW-G540A, 1.30, max UDMA/33
Mar 23 10:44:20 opt2 kernel: [ 0.992986] ata13.00: configured for UDMA/100
Mar 23 10:44:20 opt2 kernel: [ 1.032763] ata13.01: configured for UDMA/33
Mar 23 10:44:20 opt2 kernel: [ 1.092536] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 1.100038] ata9: SATA link down (SStatus 0 SControl 310)
Mar 23 10:44:20 opt2 kernel: [ 1.100100] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 1.153805] ata1.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 1.153810] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
Mar 23 10:44:20 opt2 kernel: [ 1.160291] ata5.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 1.160295] ata5.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
Mar 23 10:44:20 opt2 kernel: [ 1.243589] ata5.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 1.245425] ata1.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 1.245586] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
Mar 23 10:44:20 opt2 kernel: [ 1.245771] sd 0:0:0:0: Attached scsi generic sg0 type 0
Mar 23 10:44:20 opt2 kernel: [ 1.245835] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 23 10:44:20 opt2 kernel: [ 1.245902] sd 0:0:0:0: [sda] Write Protect is off
Mar 23 10:44:20 opt2 kernel: [ 1.245906] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Mar 23 10:44:20 opt2 kernel: [ 1.245941] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 23 10:44:20 opt2 kernel: [ 1.246141] sda: sda1 sda2
Mar 23 10:44:20 opt2 kernel: [ 1.285690] sd 0:0:0:0: [sda] Attached SCSI disk
Mar 23 10:44:20 opt2 kernel: [ 1.590036] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 1.651576] ata2.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 1.651580] ata2.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
Mar 23 10:44:20 opt2 kernel: [ 1.743201] ata2.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 1.743416] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
Mar 23 10:44:20 opt2 kernel: [ 1.743419] ata2: hotplug_status 0x22
Mar 23 10:44:20 opt2 kernel: [ 1.743427] ata2: hard resetting link
Mar 23 10:44:20 opt2 kernel: [ 2.490037] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 2.634325] ata2.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 2.634330] ata2: EH complete
Mar 23 10:44:20 opt2 kernel: [ 2.634399] scsi 1:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
Mar 23 10:44:20 opt2 kernel: [ 2.634542] sd 1:0:0:0: Attached scsi generic sg1 type 0
Mar 23 10:44:20 opt2 kernel: [ 2.634590] sd 1:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 23 10:44:20 opt2 kernel: [ 2.634650] sd 1:0:0:0: [sdb] Write Protect is off
Mar 23 10:44:20 opt2 kernel: [ 2.634653] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Mar 23 10:44:20 opt2 kernel: [ 2.634684] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 23 10:44:20 opt2 kernel: [ 2.634823] sdb: unknown partition table
Mar 23 10:44:20 opt2 kernel: [ 2.674337] sd 1:0:0:0: [sdb] Attached SCSI disk
Mar 23 10:44:20 opt2 kernel: [ 2.980037] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 3.035629] ata3.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 3.035634] ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
Mar 23 10:44:20 opt2 kernel: [ 3.118938] ata3.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 3.119149] ata3: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
Mar 23 10:44:20 opt2 kernel: [ 3.119152] ata3: hotplug_status 0x11
Mar 23 10:44:20 opt2 kernel: [ 3.119160] ata3: hard resetting link
Mar 23 10:44:20 opt2 kernel: [ 3.860037] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 4.001773] ata3.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 4.001777] ata3: EH complete
Mar 23 10:44:20 opt2 kernel: [ 4.001847] scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
Mar 23 10:44:20 opt2 kernel: [ 4.001992] sd 2:0:0:0: Attached scsi generic sg2 type 0
Mar 23 10:44:20 opt2 kernel: [ 4.002034] sd 2:0:0:0: [sdc] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 23 10:44:20 opt2 kernel: [ 4.002093] sd 2:0:0:0: [sdc] Write Protect is off
Mar 23 10:44:20 opt2 kernel: [ 4.002097] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
Mar 23 10:44:20 opt2 kernel: [ 4.002126] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 23 10:44:20 opt2 kernel: [ 4.002265] sdc: unknown partition table
Mar 23 10:44:20 opt2 kernel: [ 4.041843] sd 2:0:0:0: [sdc] Attached SCSI disk
Mar 23 10:44:20 opt2 kernel: [ 4.350037] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 4.406159] ata4.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 4.406164] ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
Mar 23 10:44:20 opt2 kernel: [ 4.489468] ata4.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 4.489679] ata4: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
Mar 23 10:44:20 opt2 kernel: [ 4.489682] ata4: hotplug_status 0x44
Mar 23 10:44:20 opt2 kernel: [ 4.489690] ata4: hard resetting link
Mar 23 10:44:20 opt2 kernel: [ 5.230038] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 5.372289] ata4.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 5.372292] ata4: EH complete
Mar 23 10:44:20 opt2 kernel: [ 5.372360] scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
Mar 23 10:44:20 opt2 kernel: [ 5.372498] sd 3:0:0:0: Attached scsi generic sg3 type 0
Mar 23 10:44:20 opt2 kernel: [ 5.372552] sd 3:0:0:0: [sdd] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 23 10:44:20 opt2 kernel: [ 5.372608] sd 3:0:0:0: [sdd] Write Protect is off
Mar 23 10:44:20 opt2 kernel: [ 5.372612] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
Mar 23 10:44:20 opt2 kernel: [ 5.372642] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 23 10:44:20 opt2 kernel: [ 5.372794] sdd:
Mar 23 10:44:20 opt2 kernel: [ 5.372884] scsi 4:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
Mar 23 10:44:20 opt2 kernel: [ 5.373031] sd 4:0:0:0: Attached scsi generic sg4 type 0
Mar 23 10:44:20 opt2 kernel: [ 5.373071] sd 4:0:0:0: [sde] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 23 10:44:20 opt2 kernel: [ 5.373125] sd 4:0:0:0: [sde] Write Protect is off
Mar 23 10:44:20 opt2 kernel: [ 5.373129] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
Mar 23 10:44:20 opt2 kernel: [ 5.373158] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 23 10:44:20 opt2 kernel: [ 5.373301] sde: unknown partition table
Mar 23 10:44:20 opt2 kernel: [ 5.389480] sd 4:0:0:0: [sde] Attached SCSI disk
Mar 23 10:44:20 opt2 kernel: [ 5.412128] unknown partition table
Mar 23 10:44:20 opt2 kernel: [ 5.412320] sd 3:0:0:0: [sdd] Attached SCSI disk
Mar 23 10:44:20 opt2 kernel: [ 5.720038] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 5.783506] ata6.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 5.783511] ata6.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
Mar 23 10:44:20 opt2 kernel: [ 5.875135] ata6.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 5.875347] ata6: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
Mar 23 10:44:20 opt2 kernel: [ 5.875350] ata6: hotplug_status 0x2
Mar 23 10:44:20 opt2 kernel: [ 5.875358] ata6: hard resetting link
Mar 23 10:44:20 opt2 kernel: [ 6.620039] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 6.757944] ata6.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 6.757948] ata6: EH complete
Mar 23 10:44:20 opt2 kernel: [ 6.758020] scsi 5:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
Mar 23 10:44:20 opt2 kernel: [ 6.758171] sd 5:0:0:0: Attached scsi generic sg5 type 0
Mar 23 10:44:20 opt2 kernel: [ 6.758213] sd 5:0:0:0: [sdf] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 23 10:44:20 opt2 kernel: [ 6.758271] sd 5:0:0:0: [sdf] Write Protect is off
Mar 23 10:44:20 opt2 kernel: [ 6.758275] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
Mar 23 10:44:20 opt2 kernel: [ 6.758306] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 23 10:44:20 opt2 kernel: [ 6.758454] sdf: unknown partition table
Mar 23 10:44:20 opt2 kernel: [ 6.797953] sd 5:0:0:0: [sdf] Attached SCSI disk
Mar 23 10:44:20 opt2 kernel: [ 7.100038] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 7.152078] ata7.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 7.152083] ata7.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
Mar 23 10:44:20 opt2 kernel: [ 7.243715] ata7.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 7.243926] ata7: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
Mar 23 10:44:20 opt2 kernel: [ 7.243929] ata7: hotplug_status 0x11
Mar 23 10:44:20 opt2 kernel: [ 7.243937] ata7: hard resetting link
Mar 23 10:44:20 opt2 kernel: [ 7.990037] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 8.134876] ata7.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 8.134880] ata7: EH complete
Mar 23 10:44:20 opt2 kernel: [ 8.134948] scsi 6:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
Mar 23 10:44:20 opt2 kernel: [ 8.135097] sd 6:0:0:0: Attached scsi generic sg6 type 0
Mar 23 10:44:20 opt2 kernel: [ 8.135138] sd 6:0:0:0: [sdg] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 23 10:44:20 opt2 kernel: [ 8.135195] sd 6:0:0:0: [sdg] Write Protect is off
Mar 23 10:44:20 opt2 kernel: [ 8.135199] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
Mar 23 10:44:20 opt2 kernel: [ 8.135228] sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 23 10:44:20 opt2 kernel: [ 8.135368] sdg: unknown partition table
Mar 23 10:44:20 opt2 kernel: [ 8.174944] sd 6:0:0:0: [sdg] Attached SCSI disk
Mar 23 10:44:20 opt2 kernel: [ 8.480038] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 8.545473] ata8.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 8.545478] ata8.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
Mar 23 10:44:20 opt2 kernel: [ 8.628773] ata8.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 8.628984] ata8: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
Mar 23 10:44:20 opt2 kernel: [ 8.628987] ata8: hotplug_status 0x44
Mar 23 10:44:20 opt2 kernel: [ 8.628995] ata8: hard resetting link
Mar 23 10:44:20 opt2 kernel: [ 9.370041] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 23 10:44:20 opt2 kernel: [ 9.503254] ata8.00: configured for UDMA/133
Mar 23 10:44:20 opt2 kernel: [ 9.503258] ata8: EH complete
Mar 23 10:44:20 opt2 kernel: [ 9.503328] scsi 7:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
Mar 23 10:44:20 opt2 kernel: [ 9.503468] sd 7:0:0:0: Attached scsi generic sg7 type 0
Mar 23 10:44:20 opt2 kernel: [ 9.503513] sd 7:0:0:0: [sdh] 625142448 512-byte logical blocks: (320 GB/298 GiB)
Mar 23 10:44:20 opt2 kernel: [ 9.503571] sd 7:0:0:0: [sdh] Write Protect is off
Mar 23 10:44:20 opt2 kernel: [ 9.503575] sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
Mar 23 10:44:20 opt2 kernel: [ 9.503606] sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 23 10:44:20 opt2 kernel: [ 9.503755] sdh: unknown partition table
Mar 23 10:44:20 opt2 kernel: [ 9.543312] sd 7:0:0:0: [sdh] Attached SCSI disk
Mar 23 10:44:20 opt2 kernel: [ 9.850034] ata10: SATA link down (SStatus 0 SControl 310)
Mar 23 10:44:20 opt2 kernel: [ 10.200037] ata11: SATA link down (SStatus 0 SControl 310)
Mar 23 10:44:20 opt2 kernel: [ 10.552533] ata12: SATA link down (SStatus 0 SControl 310)
Mar 23 10:44:20 opt2 kernel: [ 10.552625] scsi 12:0:0:0: Direct-Access ATA Maxtor 4D040H2 DAH0 PQ: 0 ANSI: 5
Mar 23 10:44:20 opt2 kernel: [ 10.552781] sd 12:0:0:0: Attached scsi generic sg8 type 0
Mar 23 10:44:20 opt2 kernel: [ 10.555645] sd 12:0:0:0: [sdi] 80043264 512-byte logical blocks: (40.9 GB/38.1 GiB)
Mar 23 10:44:20 opt2 kernel: [ 10.555701] sd 12:0:0:0: [sdi] Write Protect is off
Mar 23 10:44:20 opt2 kernel: [ 10.555706] sd 12:0:0:0: [sdi] Mode Sense: 00 3a 00 00
Mar 23 10:44:20 opt2 kernel: [ 10.555736] sd 12:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 23 10:44:20 opt2 kernel: [ 10.555880] sdi:
Mar 23 10:44:20 opt2 kernel: [ 10.593577] scsi 12:0:1:0: CD-ROM SONY DVD RW AW-G540A 1.30 PQ: 0 ANSI: 5
Mar 23 10:44:20 opt2 kernel: [ 10.599123] sd 12:0:0:0: [sdi] Attached SCSI disk
Mar 23 10:44:20 opt2 kernel: [ 10.612782] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Mar 23 10:44:20 opt2 kernel: [ 10.612788] Uniform CD-ROM driver Revision: 3.20
Mar 23 10:44:20 opt2 kernel: [ 10.612890] sr 12:0:1:0: Attached scsi CD-ROM sr0
Mar 23 10:44:20 opt2 kernel: [ 10.612944] sr 12:0:1:0: Attached scsi generic sg9 type 5
Mar 23 10:44:20 opt2 kernel: [ 10.781278] Freeing unused kernel memory: 660k freed
Mar 23 10:44:20 opt2 kernel: [ 10.781961] Write protecting the kernel read-only data: 7572k
Mar 23 10:44:20 opt2 kernel: [ 11.111781] Floppy drive(s): fd0 is 1.44M
Mar 23 10:44:20 opt2 kernel: [ 11.136166] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
Mar 23 10:44:20 opt2 kernel: [ 11.136172] e100: Copyright(c) 1999-2006 Intel Corporation
Mar 23 10:44:20 opt2 kernel: [ 11.146285] FDC 0 is a post-1991 82077
Mar 23 10:44:20 opt2 kernel: [ 11.149223] alloc irq_desc for 18 on node 0
Mar 23 10:44:20 opt2 kernel: [ 11.149230] alloc kstat_irqs on node 0
Mar 23 10:44:20 opt2 kernel: [ 11.149255] e100 0000:03:08.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Mar 23 10:44:20 opt2 kernel: [ 11.252187] e100 0000:03:08.0: PME# disabled
Mar 23 10:44:20 opt2 kernel: [ 11.253055] e100: eth0: e100_probe: addr 0xfeafb000, irq 18, MAC addr 00:e0:81:28:67:de
Mar 23 10:44:20 opt2 kernel: [ 11.253536] tg3.c:v3.99 (April 20, 2009)
Mar 23 10:44:20 opt2 kernel: [ 11.253550] alloc irq_desc for 24 on node 0
Mar 23 10:44:20 opt2 kernel: [ 11.253553] alloc kstat_irqs on node 0
Mar 23 10:44:20 opt2 kernel: [ 11.253560] tg3 0000:02:09.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
Mar 23 10:44:20 opt2 kernel: [ 11.280128] tg3 0000:02:09.0: wake-up capability disabled by ACPI
Mar 23 10:44:20 opt2 kernel: [ 11.280139] tg3 0000:02:09.0: PME# disabled
Mar 23 10:44:20 opt2 kernel: [ 11.311997] eth1: Tigon3 [partno(BCM95704A7) rev 2003] (PCI:66MHz:64-bit) MAC address 00:e0:81:28:67:fc
Mar 23 10:44:20 opt2 kernel: [ 11.312006] eth1: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1])
Mar 23 10:44:20 opt2 kernel: [ 11.312011] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
Mar 23 10:44:20 opt2 kernel: [ 11.312014] eth1: dma_rwctrl[763f0000] dma_mask[64-bit]
Mar 23 10:44:20 opt2 kernel: [ 11.324132] alloc irq_desc for 25 on node 0
Mar 23 10:44:20 opt2 kernel: [ 11.324140] alloc kstat_irqs on node 0
Mar 23 10:44:20 opt2 kernel: [ 11.324155] tg3 0000:02:09.1: PCI INT B -> GSI 25 (level, low) -> IRQ 25
Mar 23 10:44:20 opt2 kernel: [ 11.350065] tg3 0000:02:09.1: PME# disabled
Mar 23 10:44:20 opt2 kernel: [ 11.374786] eth2: Tigon3 [partno(BCM95704A7) rev 2003] (PCI:66MHz:64-bit) MAC address 00:e0:81:28:67:fd
Mar 23 10:44:20 opt2 kernel: [ 11.374793] eth2: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1])
Mar 23 10:44:20 opt2 kernel: [ 11.374798] eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
Mar 23 10:44:20 opt2 kernel: [ 11.374802] eth2: dma_rwctrl[763f0000] dma_mask[64-bit]
Mar 23 10:44:20 opt2 kernel: [ 11.739999] PM: Starting manual resume from disk
Mar 23 10:44:20 opt2 kernel: [ 11.740008] PM: Resume from partition 8:1
Mar 23 10:44:20 opt2 kernel: [ 11.740011] PM: Checking hibernation image.
Mar 23 10:44:20 opt2 kernel: [ 11.740122] PM: Resume from disk failed.
Mar 23 10:44:20 opt2 kernel: [ 11.756191] EXT4-fs (sda2): INFO: recovery required on readonly filesystem
Mar 23 10:44:20 opt2 kernel: [ 11.756199] EXT4-fs (sda2): write access will be enabled during recovery
Mar 23 10:44:20 opt2 kernel: [ 11.760544] EXT4-fs (sda2): barriers enabled
Mar 23 10:44:20 opt2 kernel: [ 16.760982] kjournald2 starting: pid 400, dev sda2:8, commit interval 5 seconds
Mar 23 10:44:20 opt2 kernel: [ 16.761028] EXT4-fs (sda2): delayed allocation enabled
Mar 23 10:44:20 opt2 kernel: [ 16.761034] EXT4-fs: file extents enabled
Mar 23 10:44:20 opt2 kernel: [ 16.827590] EXT4-fs: mballoc enabled
Mar 23 10:44:20 opt2 kernel: [ 16.827618] EXT4-fs (sda2): orphan cleanup on readonly fs
Mar 23 10:44:20 opt2 kernel: [ 16.827633] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 416
Mar 23 10:44:20 opt2 kernel: [ 16.827799] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 410
Mar 23 10:44:20 opt2 kernel: [ 16.827890] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 407
Mar 23 10:44:20 opt2 kernel: [ 16.827920] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 405
Mar 23 10:44:20 opt2 kernel: [ 16.827951] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 403
Mar 23 10:44:20 opt2 kernel: [ 16.827980] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 402
Mar 23 10:44:20 opt2 kernel: [ 16.828011] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 396
Mar 23 10:44:20 opt2 kernel: [ 16.828080] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 393
Mar 23 10:44:20 opt2 kernel: [ 16.828109] EXT4-fs (sda2): 8 orphan inodes deleted
Mar 23 10:44:20 opt2 kernel: [ 16.828114] EXT4-fs (sda2): recovery complete
Mar 23 10:44:20 opt2 kernel: [ 17.569454] EXT4-fs (sda2): mounted filesystem with ordered data mode
Mar 23 10:44:20 opt2 kernel: [ 18.044899] type=1505 audit(1269362657.664:2): operation="profile_load" pid=421 name=/sbin/dhclient3
Mar 23 10:44:20 opt2 kernel: [ 18.045334] type=1505 audit(1269362657.664:3): operation="profile_load" pid=421 name=/usr/lib/NetworkManager/nm-dhcp-client.action
Mar 23 10:44:20 opt2 kernel: [ 18.045576] type=1505 audit(1269362657.664:4): operation="profile_load" pid=421 name=/usr/lib/connman/scripts/dhclient-script
Mar 23 10:44:20 opt2 kernel: [ 18.048803] type=1505 audit(1269362657.664:5): operation="profile_load" pid=422 name=/usr/sbin/tcpdump
Mar 23 10:44:20 opt2 kernel: [ 18.586156] Adding 1951856k swap on /dev/sda1. Priority:-1 extents:1 across:1951856k
Mar 23 10:44:20 opt2 kernel: [ 18.881171] EXT4-fs (sda2): internal journal on sda2:8
Mar 23 10:44:20 opt2 kernel: [ 18.996738] udev: starting version 147
Mar 23 10:44:20 opt2 kernel: [ 19.971463] parport_pc 00:08: reported by Plug and Play ACPI
Mar 23 10:44:20 opt2 kernel: [ 19.971526] parport0: PC-style at 0x378, irq 7 [PCSPP]
Mar 23 10:44:20 opt2 kernel: [ 19.982287] shpchp 0000:00:06.0: HPC vendor_id 1022 device_id 7460 ss_vid 0 ss_did 0
Mar 23 10:44:20 opt2 kernel: [ 19.982295] shpchp 0000:00:06.0: Cannot reserve MMIO region
Mar 23 10:44:20 opt2 kernel: [ 19.983057] shpchp 0000:00:0a.0: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0
Mar 23 10:44:20 opt2 kernel: [ 19.983062] shpchp 0000:00:0a.0: Cannot reserve MMIO region
Mar 23 10:44:20 opt2 kernel: [ 19.983219] shpchp 0000:00:0b.0: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0
Mar 23 10:44:20 opt2 kernel: [ 19.983224] shpchp 0000:00:0b.0: Cannot reserve MMIO region
Mar 23 10:44:20 opt2 kernel: [ 19.983363] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Mar 23 10:44:20 opt2 kernel: [ 20.071977] EDAC MC: Ver: 2.1.0 Oct 16 2009
Mar 23 10:44:20 opt2 kernel: [ 20.130097] lp0: using parport0 (interrupt-driven).
Mar 23 10:44:20 opt2 kernel: [ 20.170112] EDAC amd64_edac: Ver: 3.2.0 Oct 16 2009
Mar 23 10:44:20 opt2 kernel: [ 20.173157] ppdev: user-space parallel port driver
Mar 23 10:44:20 opt2 kernel: [ 20.190054] EDAC amd64: ECC is enabled by BIOS, Proceeding with EDAC module initialization
Mar 23 10:44:20 opt2 kernel: [ 20.216667] EDAC amd64: ECC is enabled by BIOS, Proceeding with EDAC module initialization
Mar 23 10:44:20 opt2 kernel: [ 20.216748] EDAC MC: Rev E or earlier detected
Mar 23 10:44:20 opt2 kernel: [ 20.216870] EDAC MC0: Giving out device to 'amd64_edac' 'RevF': DEV 0000:00:18.2
Mar 23 10:44:20 opt2 kernel: [ 20.216874] EDAC MC: Rev E or earlier detected
Mar 23 10:44:20 opt2 kernel: [ 20.216951] EDAC MC1: Giving out device to 'amd64_edac' 'RevF': DEV 0000:00:19.2
Mar 23 10:44:20 opt2 kernel: [ 20.216987] EDAC PCI0: Giving out device to module 'amd64_edac' controller 'EDAC PCI controller': DEV '0000:00:18.2' (POLLED)
Mar 23 10:44:20 opt2 kernel: [ 20.249972] AMD768 RNG detected
Mar 23 10:44:20 opt2 kernel: [ 20.365190] ACPI: I/O resource amd756_smbus [0x50e0-0x50ef] conflicts with ACPI region PMIO [0x5000-0x50fe]
Mar 23 10:44:20 opt2 kernel: [ 20.365289] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
Mar 23 10:44:20 opt2 kernel: [ 20.365322] amd756_smbus: probe of 0000:00:07.3 failed with error -16
Mar 23 10:44:20 opt2 kernel: [ 20.366257] ACPI: I/O resource 0000:00:07.2 [0xcc00-0xcc1f] conflicts with ACPI region ECIO [0xcc00-0xcc1f]
Mar 23 10:44:20 opt2 kernel: [ 20.366353] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
Mar 23 10:44:20 opt2 kernel: [ 20.366378] amd8111_smbus2: probe of 0000:00:07.2 failed with error -16
Mar 23 10:44:20 opt2 kernel: [ 20.590402] ip_tables: (C) 2000-2006 Netfilter Core Team
Mar 23 10:44:20 opt2 kernel: [ 20.608635] udev: renamed network interface eth2 to eth1
Mar 23 10:44:20 opt2 kernel: [ 20.655723] udev: renamed network interface eth1_rename to eth0
Mar 23 10:44:20 opt2 kernel: [ 20.656699] udev: renamed network interface eth0_rename to eth2
Mar 23 10:44:20 opt2 kernel: [ 20.781721] e100 0000:03:08.0: firmware: requesting e100/d102e_ucode.bin
Mar 23 10:44:20 opt2 kernel: [ 21.040831] ADDRCONF(NETDEV_UP): eth2: link is not ready
Mar 23 10:44:20 opt2 kernel: [ 21.080762] tg3 0000:02:09.1: firmware: requesting tigon/tg3_tso.bin
Mar 23 10:44:21 opt2 kernel: [ 21.458804] type=1505 audit(1269362661.071:6): operation="profile_replace" pid=860 name=/sbin/dhclient3
Mar 23 10:44:21 opt2 kernel: [ 21.459248] type=1505 audit(1269362661.071:7): operation="profile_replace" pid=860 name=/usr/lib/NetworkManager/nm-dhcp-client.action
Mar 23 10:44:21 opt2 kernel: [ 21.459501] type=1505 audit(1269362661.071:8): operation="profile_replace" pid=860 name=/usr/lib/connman/scripts/dhclient-script
Mar 23 10:44:21 opt2 kernel: [ 21.461582] tg3 0000:02:09.1: PME# disabled
Mar 23 10:44:21 opt2 kernel: [ 21.517438] ADDRCONF(NETDEV_UP): eth1: link is not ready
Mar 23 10:44:21 opt2 kernel: [ 21.518350] type=1505 audit(1269362661.131:9): operation="profile_replace" pid=864 name=/usr/sbin/tcpdump
Mar 23 10:44:21 opt2 kernel: [ 21.597857] tg3 0000:02:09.0: firmware: requesting tigon/tg3_tso.bin
Mar 23 10:44:21 opt2 kernel: [ 21.614472] tg3 0000:02:09.0: wake-up capability disabled by ACPI
Mar 23 10:44:21 opt2 kernel: [ 21.614481] tg3 0000:02:09.0: PME# disabled
Mar 23 10:44:21 opt2 kernel: [ 21.680769] ADDRCONF(NETDEV_UP): eth0: link is not ready
Mar 23 10:44:21 opt2 init: apport pre-start process (1050) terminated with status 1
Mar 23 10:44:21 opt2 init: apport post-stop process (1063) terminated with status 1
Mar 23 10:44:21 opt2 cron[1054]: (CRON) INFO (pidfile fd = 3)
Mar 23 10:44:21 opt2 cron[1068]: (CRON) STARTUP (fork ok)
Mar 23 10:44:22 opt2 cron[1068]: (CRON) INFO (Running @reboot jobs)
Mar 23 10:44:22 opt2 kernel: [ 23.040279] e100: eth2 NIC Link is Up 100 Mbps Full Duplex
Mar 23 10:44:22 opt2 kernel: [ 23.041074] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
Mar 23 10:44:22 opt2 ntpdate[919]: step time server 91.189.94.4 offset -0.564254 sec
Mar 23 10:44:23 opt2 kernel: [ 24.630033] tg3: eth1: Link is up at 1000 Mbps, full duplex.
Mar 23 10:44:23 opt2 kernel: [ 24.630040] tg3: eth1: Flow control is on for TX and on for RX.
Mar 23 10:44:23 opt2 kernel: [ 24.630720] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Mar 23 10:44:26 opt2 kernel: [ 27.320046] tg3: eth0: Link is up at 1000 Mbps, full duplex.
Mar 23 10:44:26 opt2 kernel: [ 27.320054] tg3: eth0: Flow control is on for TX and on for RX.
Mar 23 10:44:26 opt2 kernel: [ 27.320718] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Mar 23 10:44:26 opt2 ntpdate[1131]: step time server 91.189.94.4 offset 0.000606 sec
Mar 23 10:44:27 opt2 kernel: [ 28.585782] tg3: eth0: Link is down.
Mar 23 10:44:30 opt2 kernel: [ 30.978660] tg3: eth0: Link is up at 1000 Mbps, full duplex.
Mar 23 10:44:30 opt2 kernel: [ 30.978664] tg3: eth0: Flow control is on for TX and on for RX.
Mar 23 10:44:31 opt2 kernel: [ 32.098774] tg3: eth0: Link is down.
Mar 23 10:44:32 opt2 kernel: [ 33.800012] eth2: no IPv6 routers present
Mar 23 10:44:33 opt2 kernel: [ 34.910015] eth1: no IPv6 routers present
Mar 23 10:44:36 opt2 kernel: [ 37.560017] eth0: no IPv6 routers present
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Regression: my systems can no longer boot from an ide hard drive
2010-03-24 0:46 ` Mike Hayward
@ 2010-03-24 23:47 ` Robert Hancock
2010-03-25 20:25 ` Mike Hayward
0 siblings, 1 reply; 5+ messages in thread
From: Robert Hancock @ 2010-03-24 23:47 UTC (permalink / raw)
To: Mike Hayward; +Cc: randy.dunlap, linux-ide
On Tue, Mar 23, 2010 at 6:46 PM, Mike Hayward <hayward@loup.net> wrote:
> > Most likely the IDE drive isn't being detected properly, but we need
> > more info on the hardware. Can you post the dmesg output from bootup
> > with a working kernel? (If you can, the boot messages from the ones that
> > fail to boot would be ideal. For the Fedora one, you can edit the kernel
> > command line in grub and take the "quiet" off the end to see more of
> > them on the screen, any ata output would be useful..)
>
> Ok, here goes with a working ubuntu system. Getting logs from failed
> to boot systems is a challenge; none of the Fedora logs had anything
> obvious to me at the tail but I couldn't review them all. Systems are
> production so I couldn't keep offline after weekend.
>
> This is from literally the same exact installation process except to a
> different drive. The ide hard drive works just fine after booting
> from sata. Hopefully boot messages can help. Any ideas why Ubuntu
> didn't even bring up grub when pressing keys? I am not so familiar
> with it, but guessing boot loader wedged before kernel bootstrap.
This one looks normal.. so it only fails if you actually boot from the
IDE drive? That's a bit odd. What if you boot from a Fedora install
disc in rescue mode - can it see the drive then?
I'm not too familiar with the Ubuntu boot process - it could be the
kernel messages are set up to be so quiet you don't get any output
even if it can't mount the root file system, etc.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Regression: my systems can no longer boot from an ide hard drive
2010-03-24 23:47 ` Robert Hancock
@ 2010-03-25 20:25 ` Mike Hayward
0 siblings, 0 replies; 5+ messages in thread
From: Mike Hayward @ 2010-03-25 20:25 UTC (permalink / raw)
To: Robert Hancock; +Cc: randy.dunlap, linux-ide
Hi Robert,
| This one looks normal.. so it only fails if you actually boot from the
| IDE drive? That's a bit odd. What if you boot from a Fedora install
| disc in rescue mode - can it see the drive then?
|
| I'm not too familiar with the Ubuntu boot process - it could be the
| kernel messages are set up to be so quiet you don't get any output
| even if it can't mount the root file system, etc.
Yeah, I'm a RedHat man from the very first box they sent me back when
it seemed like a silly idea to "sell" free stuff. Ubuntu still has
kinks to work out with their server or advanced installs for sure.
I narrowed the problem down with Fedora 12 x86_64. You can dump into
grub at boot so it get's through 1.5 and I guess maybe to stage 2. I
see no menu or config stuff when smashing F1 to get into it and can't
seem to drive it to do anything from it's command line. But if I let
it run, it'll strap the kernel in just fine, but then the kernel
doesn't like the disks too well.
The problem appears to be with ident order I think. During install
the ide drive is /dev/sda now with the newer kernels. Even when
booting from the ide, it thinks the ide is on /dev/sda. If you
install to a sata drive, it will be /dev/sda and the ide drive ends up
being idented after all sata at /dev/sdi! Even via sata that threw me
off once and I ended up corrupting the boot drive with random ios.
I am appending fdisk output and the boot messages from one of these
opterons from the rescue mode with the ide drive mounted. You can see
the ubuntu distro which will actually boot installed to one of the
much larger sata drives as well.
The other strange thing is that the boot messages if you let it run
claim it's trying to set up a raid array for some reason. I never did
anything whatsoever related to raid on these partitions or drives. No
idea why that is happening, but I will email you screen shots of that
seperately from my G1.
- Mike
Disk /dev/sda: 41.0 GB, 40982151168 bytes
255 heads, 63 sectors/track, 4982 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x99999999
Device Boot Start End Blocks Id System
/dev/sda1 * 1 26 204800 83 Linux
Partition 1 does not end on cylinder boundary.
/dev/sda2 26 287 2097152 82 Linux swap / Solaris
Partition 2 does not end on cylinder boundary.
/dev/sda3 287 4982 37715931+ 83 Linux
Disk /dev/sdb: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00087ccf
Device Boot Start End Blocks Id System
/dev/sdb1 1 243 1951866 82 Linux swap / Solaris
/dev/sdb2 * 244 38913 310616775 83 Linux
Disk /dev/sdc: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/sdd: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/sde: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/sdf: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/sdg: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/sdh: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/sdi: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.31.5-127.fc12.x86_64 (mockbuild@x86-4.fedora.phx.redhat.com) (gcc version 4.4.2 20091027 (Red Hat 4.4.2-7) (GCC) ) #1 SMP Sat Nov 7 21:11:14 EST 2009
Command line: initrd=initrd.img stage2=hd:LABEL="Fedora" rescue BOOT_IMAGE=vmlinuz
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
BIOS-e820: 000000007fff0000 - 000000007ffff000 (ACPI data)
BIOS-e820: 000000007ffff000 - 0000000080000000 (ACPI NVS)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
DMI 2.3 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7fff0 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-EFFFF uncachable
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 0000000000 mask FF80000000 write-back
1 disabled
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-000000007fff0000
0000000000 - 007fe00000 page 2M
007fe00000 - 007fff0000 page 4k
kernel direct mapping tables up to 7fff0000 @ 10000-14000
RAMDISK: 7e95b000 - 7ffce474
ACPI: RSDP 00000000000f4620 00014 (v00 ACPIAM)
ACPI: RSDT 000000007fff0000 00034 (v01 A M I OEMRSDT 10000304 MSFT 00000097)
ACPI: FACP 000000007fff0200 00081 (v02 A M I OEMFACP 10000304 MSFT 00000097)
ACPI: DSDT 000000007fff0400 03086 (v01 0AAAA 0AAAA000 00000000 INTL 02002026)
ACPI: FACS 000000007ffff000 00040
ACPI: APIC 000000007fff0380 00074 (v01 A M I OEMAPIC 10000304 MSFT 00000097)
ACPI: OEMB 000000007ffff040 0005E (v01 A M I OEMBIOS 10000304 MSFT 00000097)
ACPI: ASF! 000000007fff3490 00086 (v16 AMIASF AMDSTRET 00000001 INTL 02002026)
ACPI: Local APIC address 0xfee00000
Scanning NUMA topology in Northbridge 24
Number of nodes 2
Node 0 MemBase 0000000000000000 Limit 0000000040000000
Node 1 MemBase 0000000040000000 Limit 000000007fff0000
NUMA: Using 30 for the hash shift.
Using node hash shift of 30
found SMP MP-table at [ffff8800000ff780] ff780
ACPI: Local APIC address 0xfee00000
Bootmem setup node 0 0000000000000000-0000000040000000
NODE_DATA [0000000000012000 - 0000000000027fff]
bootmap [0000000000028000 - 000000000002ffff] pages 8
(7 early reservations) ==> bootmem [0000000000 - 0040000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0001000000 - 00019adb00] TEXT DATA BSS ==> [0001000000 - 00019adb00]
#3 [007e95b000 - 007ffce474] RAMDISK
#4 [000009d400 - 0000100000] BIOS reserved ==> [000009d400 - 0000100000]
#5 [00019ae000 - 00019ae280] BRK ==> [00019ae000 - 00019ae280]
#6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
Bootmem setup node 1 0000000040000000-000000007fff0000
NODE_DATA [0000000040000000 - 0000000040015fff]
bootmap [0000000040016000 - 000000004001dfff] pages 8
(7 early reservations) ==> bootmem [0040000000 - 007fff0000]
#0 [0000000000 - 0000001000] BIOS data page
#1 [0000006000 - 0000008000] TRAMPOLINE
#2 [0001000000 - 00019adb00] TEXT DATA BSS
#3 [007e95b000 - 007ffce474] RAMDISK ==> [007e95b000 - 007ffce474]
#4 [000009d400 - 0000100000] BIOS reserved
#5 [00019ae000 - 00019ae280] BRK
#6 [0000010000 - 0000012000] PGTABLE
found SMP MP-table at [ffff8800000ff780] ff780
[ffffea0000000000-ffffea0000dfffff] PMD -> [ffff880001e00000-ffff880002bfffff] on node 0
[ffffea0000e00000-ffffea0001bfffff] PMD -> [ffff880040200000-ffff880040ffffff] on node 1
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x00040000
1: 0x00040000 -> 0x0007fff0
On node 0 totalpages: 262031
DMA zone: 56 pages used for memmap
DMA zone: 103 pages reserved
DMA zone: 3824 pages, LIFO batch:0
DMA32 zone: 3528 pages used for memmap
DMA32 zone: 254520 pages, LIFO batch:31
On node 1 totalpages: 262128
DMA32 zone: 3584 pages used for memmap
DMA32 zone: 258544 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x5008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfebff000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 17, address 0xfebff000, GSI 24-27
ACPI: IOAPIC (id[0x04] address[0xfebfe000] gsi_base[28])
IOAPIC[2]: apic_id 4, version 17, address 0xfebfe000, GSI 28-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 32
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 80000000:7f7c0000)
NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:2 nr_node_ids:2
PERCPU: Remapped at ffffc90000000000 with large pages, static data 90080 bytes
Built 2 zonelists in Node order, mobility grouping on. Total pages: 516888
Policy zone: DMA32
Kernel command line: initrd=initrd.img stage2=hd:LABEL="Fedora" rescue BOOT_IMAGE=vmlinuz
PID hash table entries: 4096 (order: 12, 32768 bytes)
Initializing CPU#0
Checking aperture...
No AGP bridge found
Node 0: aperture @ eff2000000 size 32 MB
Aperture beyond 4GB. Ignoring.
Memory: 2034480k/2097088k available (4227k kernel code, 452k absent, 62156k reserved, 2926k data, 1324k init)
SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=2
Hierarchical RCU implementation.
NR_IRQS:4352 nr_irqs:512
Fast TSC calibration failed
TSC: PIT calibration matches PMTIMER. 2 loops
Detected 1397.518 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
allocated 20971520 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Calibrating delay loop (skipped), value calculated using timer frequency.. 2795.03 BogoMIPS (lpj=1397518)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0x0 -> Node 0
tseg: 0000000000
mce: CPU supports 5 MCE banks
Performance Counters: AMD PMU driver.
... version: 0
... bit width: 48
... generic counters: 4
... value mask: 0000ffffffffffff
... max period: 00007fffffffffff
... fixed-purpose counters: 0
... counter mask: 000000000000000f
ACPI: Core revision 20090521
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 20852 entries in 82 pages
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: AMD Opteron(tm) Processor 240 stepping 01
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 2794.47 BogoMIPS (lpj=1397235)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/0x1 -> Node 1
mce: CPU supports 5 MCE banks
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: AMD Opteron(tm) Processor 240 stepping 01
Brought up 2 CPUs
Total of 2 processors activated (5589.50 BogoMIPS).
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=584 bytes
sizeof(dentry)=192 bytes
sizeof(ext3inode)=776 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=248 bytes
sizeof(task_struct)=6008 bytes
CPU0 attaching sched-domain:
domain 0: span 0-1 level NODE
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level NODE
groups: 1 0
Booting paravirtualized kernel on bare hardware
regulator: core version 0.5
Time: 19:57:49 Date: 03/25/10
NET: Registered protocol family 16
node 0 link 0: io port [0, ffffff]
TOM: 0000000080000000 aka 2048M
node 0 link 0: mmio [a0000, bffff]
node 0 link 0: mmio [80000000, ffffffff]
bus: [00,ff] on node 0 link 0
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [a0000, bffff]
bus: 00 index 2 mmio: [80000000, fcffffffff]
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:07.1: reg 20 io port: [0xffa0-0xffaf]
pci 0000:00:07.2: reg 10 io port: [0xcc00-0xcc1f]
pci 0000:00:0a.1: reg 10 64bit mmio: [0xfebff000-0xfebfffff]
pci 0000:00:0b.1: reg 10 64bit mmio: [0xfebfe000-0xfebfefff]
pci 0000:03:00.0: reg 10 32bit mmio: [0xfeafc000-0xfeafcfff]
pci 0000:03:00.1: reg 10 32bit mmio: [0xfeafd000-0xfeafdfff]
pci 0000:03:05.0: reg 10 io port: [0xac00-0xac07]
pci 0000:03:05.0: reg 14 io port: [0xa480-0xa483]
pci 0000:03:05.0: reg 18 io port: [0xa400-0xa407]
pci 0000:03:05.0: reg 1c io port: [0xa080-0xa083]
pci 0000:03:05.0: reg 20 io port: [0xa000-0xa00f]
pci 0000:03:05.0: reg 24 32bit mmio: [0xfeafec00-0xfeafefff]
pci 0000:03:05.0: reg 30 32bit mmio: [0xfea00000-0xfea7ffff]
pci 0000:03:05.0: supports D1 D2
pci 0000:03:06.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
pci 0000:03:06.0: reg 14 io port: [0xa800-0xa8ff]
pci 0000:03:06.0: reg 18 32bit mmio: [0xfeaff000-0xfeafffff]
pci 0000:03:06.0: reg 30 32bit mmio: [0xfeac0000-0xfeadffff]
pci 0000:03:06.0: supports D1 D2
pci 0000:03:08.0: reg 10 32bit mmio: [0xfeafb000-0xfeafbfff]
pci 0000:03:08.0: reg 14 io port: [0x9c00-0x9c3f]
pci 0000:03:08.0: reg 18 32bit mmio: [0xfeaa0000-0xfeabffff]
pci 0000:03:08.0: supports D1 D2
pci 0000:03:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:03:08.0: PME# disabled
pci 0000:00:06.0: bridge io port: [0x9000-0xafff]
pci 0000:00:06.0: bridge 32bit mmio: [0xfc900000-0xfeafffff]
pci 0000:00:06.0: bridge 32bit mmio pref: [0xff500000-0xff5fffff]
pci 0000:02:02.0: reg 10 io port: [0x8c00-0x8c7f]
pci 0000:02:02.0: reg 18 io port: [0x8800-0x88ff]
pci 0000:02:02.0: reg 1c 32bit mmio: [0xfc8ff000-0xfc8fffff]
pci 0000:02:02.0: reg 20 32bit mmio: [0xfc8c0000-0xfc8dffff]
pci 0000:02:02.0: reg 30 32bit mmio: [0xfc8f0000-0xfc8f7fff]
pci 0000:02:02.0: supports D1
pci 0000:02:09.0: reg 10 64bit mmio: [0xfc890000-0xfc89ffff]
pci 0000:02:09.0: reg 18 64bit mmio: [0xfc880000-0xfc88ffff]
pci 0000:02:09.0: reg 30 32bit mmio: [0xfc870000-0xfc87ffff]
pci 0000:02:09.0: PME# supported from D3hot D3cold
pci 0000:02:09.0: PME# disabled
pci 0000:02:09.1: reg 10 64bit mmio: [0xfc8e0000-0xfc8effff]
pci 0000:02:09.1: reg 18 64bit mmio: [0xfc8b0000-0xfc8bffff]
pci 0000:02:09.1: reg 30 32bit mmio: [0xfc8a0000-0xfc8affff]
pci 0000:02:09.1: PME# supported from D3hot D3cold
pci 0000:02:09.1: PME# disabled
pci 0000:00:0a.0: bridge io port: [0x8000-0x8fff]
pci 0000:00:0a.0: bridge 32bit mmio: [0xfc700000-0xfc8fffff]
pci 0000:00:0a.0: bridge 64bit mmio pref: [0xff400000-0xff4fffff]
pci 0000:01:03.0: reg 10 io port: [0x7c00-0x7c7f]
pci 0000:01:03.0: reg 18 io port: [0x7800-0x78ff]
pci 0000:01:03.0: reg 1c 32bit mmio: [0xfc6ff000-0xfc6fffff]
pci 0000:01:03.0: reg 20 32bit mmio: [0xfc6c0000-0xfc6dffff]
pci 0000:01:03.0: reg 30 32bit mmio: [0xfc6f0000-0xfc6f7fff]
pci 0000:01:03.0: supports D1
pci 0000:00:0b.0: bridge io port: [0x7000-0x7fff]
pci 0000:00:0b.0: bridge 32bit mmio: [0xfc600000-0xfc6fffff]
pci 0000:00:0b.0: bridge 64bit mmio pref: [0xff300000-0xff3fffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
vgaarb: device added: PCI:0000:03:06.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:09: ioport range 0x680-0x6ff has been reserved
system 00:09: ioport range 0x295-0x296 has been reserved
system 00:09: ioport range 0x778-0x77f has been reserved
system 00:09: ioport range 0xb78-0xb7f has been reserved
system 00:09: ioport range 0xf78-0xf7f has been reserved
system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
system 00:0a: ioport range 0x5000-0x50bf has been reserved
system 00:0a: ioport range 0x50e0-0x50ff has been reserved
system 00:0a: ioport range 0x50c0-0x50df has been reserved
system 00:0a: ioport range 0xde00-0xde7f has been reserved
system 00:0a: ioport range 0xde80-0xdeff has been reserved
system 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0b: iomem range 0xfff80000-0xffffffff has been reserved
system 00:0c: iomem range 0x0-0x9ffff could not be reserved
system 00:0c: iomem range 0xc0000-0xdffff has been reserved
system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
system 00:0c: iomem range 0x100000-0x7fffffff could not be reserved
pci 0000:00:06.0: PCI bridge, secondary bus 0000:03
Switched to high resolution mode on CPU 0
pci 0000:00:06.0: IO window: 0x9000-0xafff
pci 0000:00:06.0: MEM window: 0xfc900000-0xfeafffff
pci 0000:00:06.0: PREFETCH window: 0xff500000-0xff5fffff
Switched to high resolution mode on CPU 1
pci 0000:00:0a.0: PCI bridge, secondary bus 0000:02
pci 0000:00:0a.0: IO window: 0x8000-0x8fff
pci 0000:00:0a.0: MEM window: 0xfc700000-0xfc8fffff
pci 0000:00:0a.0: PREFETCH window: 0x000000ff400000-0x000000ff4fffff
pci 0000:00:0b.0: PCI bridge, secondary bus 0000:01
pci 0000:00:0b.0: IO window: 0x7000-0x7fff
pci 0000:00:0b.0: MEM window: 0xfc600000-0xfc6fffff
pci 0000:00:0b.0: PREFETCH window: 0x000000ff300000-0x000000ff3fffff
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:03: resource 0 io: [0x9000-0xafff]
pci_bus 0000:03: resource 1 mem: [0xfc900000-0xfeafffff]
pci_bus 0000:03: resource 2 pref mem [0xff500000-0xff5fffff]
pci_bus 0000:02: resource 0 io: [0x8000-0x8fff]
pci_bus 0000:02: resource 1 mem: [0xfc700000-0xfc8fffff]
pci_bus 0000:02: resource 2 pref mem [0xff400000-0xff4fffff]
pci_bus 0000:01: resource 0 io: [0x7000-0x7fff]
pci_bus 0000:01: resource 1 mem: [0xfc600000-0xfc6fffff]
pci_bus 0000:01: resource 2 pref mem [0xff300000-0xff3fffff]
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 22989k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1269547069.989:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 4018
SELinux: Registering netfilter hooks
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
boot interrupts on PCI device 0x1022:0x746b already disabled
pci 0000:00:0a.0: MSI quirk detected; subordinate MSI disabled
disabled boot interrupts on PCI device 0x1022:0x7450
pci 0000:00:0a.0: AMD8131 rev 12 detected; disabling PCI-X MMRBC
pci 0000:00:0b.0: MSI quirk detected; subordinate MSI disabled
disabled boot interrupts on PCI device 0x1022:0x7450
pci 0000:00:0b.0: AMD8131 rev 12 detected; disabling PCI-X MMRBC
pci 0000:03:06.0: Boot video device
pci 0000:03:08.0: Firmware left e100 interrupts enabled; disabling
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button [PWRF]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
ACPI: Power Button [PWRB]
ACPI: processor limited to max C-state 1
processor LNXCPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
processor LNXCPU:01: registered as cooling_device1
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input2
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
alloc irq_desc for 19 on node 0
alloc kstat_irqs on node 0
ohci_hcd 0000:03:00.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:03:00.0: OHCI Host Controller
ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:03:00.0: irq 19, io mem 0xfeafc000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31.5-127.fc12.x86_64 ohci_hcd
usb usb1: SerialNumber: 0000:03:00.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:03:00.1: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:03:00.1: OHCI Host Controller
ohci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:03:00.1: irq 19, io mem 0xfeafd000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31.5-127.fc12.x86_64 ohci_hcd
usb usb2: SerialNumber: 0000:03:00.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:02: RTC can wake from S4
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 114 bytes nvram
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
PM: Resume from disk failed.
registered taskstats version 1
No TPM chip found, activating TPM-bypass!
Magic number: 2:319:1002
pnp 00:04: hash matches
rtc_cmos 00:02: setting system clock to 2010-03-25 19:57:51 UTC (1269547071)
Initalizing network drop monitor service
Freeing unused kernel memory: 1324k freed
Write protecting the kernel read-only data: 6344k
usb 1-3: new low speed USB device using ohci_hcd and address 2
usb 1-3: New USB device found, idVendor=1241, idProduct=f760
usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-3: Product: Wireless Keyboard/Mouse(2.4G)
usb 1-3: Manufacturer:
usb 1-3: configuration #1 chosen from 1 choice
input: Wireless Keyboard/Mouse(2.4G) as /devices/pci0000:00/0000:00:06.0/0000:03:00.0/usb1/1-3/1-3:1.0/input/input3
generic-usb 0003:1241:F760.0001: input,hidraw0: USB HID v1.10 Keyboard [ Wireless Keyboard/Mouse(2.4G)] on usb-0000:03:00.0-3/input0
input: Wireless Keyboard/Mouse(2.4G) as /devices/pci0000:00/0000:00:06.0/0000:03:00.0/usb1/1-3/1-3:1.1/input/input4
generic-usb 0003:1241:F760.0002: input,hidraw1: USB HID v1.10 Mouse [ Wireless Keyboard/Mouse(2.4G)] on usb-0000:03:00.0-3/input1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
input: PC Speaker as /devices/platform/pcspkr/input/input5
No iBFT detected.
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
pata_amd 0000:00:07.1: version 0.4.1
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
sata_promise 0000:02:02.0: version 2.12
alloc irq_desc for 26 on node 0
alloc kstat_irqs on node 0
sata_promise 0000:02:02.0: PCI INT A -> GSI 26 (level, low) -> IRQ 26
scsi2 : sata_promise
alloc irq_desc for 18 on node 0
alloc kstat_irqs on node 0
e100 0000:03:08.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
e100 0000:03:08.0: PME# disabled
scsi3 : sata_promise
scsi4 : sata_promise
ata1.00: ATA-6: Maxtor 4D040H2, DAH017K0, max UDMA/100
ata1.00: 80043264 sectors, multi 16: LBA
ata1.01: ATAPI: SONY DVD RW AW-G540A, 1.30, max UDMA/33
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA Maxtor 4D040H2 DAH0 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 0:0:1:0: CD-ROM SONY DVD RW AW-G540A 1.30 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:1:0: Attached scsi CD-ROM sr0
sr 0:0:1:0: Attached scsi generic sg1 type 5
sd 0:0:0:0: [sda] 80043264 512-byte logical blocks: (40.9 GB/38.1 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
scsi5 : sata_promise
ata3: SATA max UDMA/133 mmio m4096@0xfc8ff000 ata 0xfc8ff380 irq 26
ata4: SATA max UDMA/133 mmio m4096@0xfc8ff000 ata 0xfc8ff280 irq 26
ata5: SATA max UDMA/133 mmio m4096@0xfc8ff000 ata 0xfc8ff200 irq 26
ata6: SATA max UDMA/133 mmio m4096@0xfc8ff000 ata 0xfc8ff300 irq 26
sda1 sda2 sda3
alloc irq_desc for 28 on node 0
alloc kstat_irqs on node 0
sata_promise 0000:01:03.0: PCI INT A -> GSI 28 (level, low) -> IRQ 28
scsi6 : sata_promise
tg3.c:v3.99 (April 20, 2009)
alloc irq_desc for 24 on node 0
alloc kstat_irqs on node 0
tg3 0000:02:09.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
scsi7 : sata_promise
scsi8 : sata_promise
tg3 0000:02:09.0: wake-up capability disabled by ACPI
tg3 0000:02:09.0: PME# disabled
scsi9 : sata_promise
ata7: SATA max UDMA/133 mmio m4096@0xfc6ff000 ata 0xfc6ff380 irq 28
ata8: SATA max UDMA/133 mmio m4096@0xfc6ff000 ata 0xfc6ff280 irq 28
ata9: SATA max UDMA/133 mmio m4096@0xfc6ff000 ata 0xfc6ff200 irq 28
ata10: SATA max UDMA/133 mmio m4096@0xfc6ff000 ata 0xfc6ff300 irq 28
eth0: Tigon3 [partno(BCM95704A7) rev 2003] (PCI:66MHz:64-bit) MAC address 00:e0:81:28:67:9a
eth0: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
alloc irq_desc for 25 on node 0
alloc kstat_irqs on node 0
tg3 0000:02:09.1: PCI INT B -> GSI 25 (level, low) -> IRQ 25
sd 0:0:0:0: [sda] Attached SCSI disk
tg3 0000:02:09.1: PME# disabled
e100: eth1: e100_probe: addr 0xfeafb000, irq 18, MAC addr 00:e0:81:28:67:65
sata_sil 0000:03:05.0: version 2.4
sata_sil 0000:03:05.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
sata_sil 0000:03:05.0: Applying R_ERR on DMA activate FIS errata fix
scsi10 : sata_sil
eth2: Tigon3 [partno(BCM95704A7) rev 2003] (PCI:66MHz:64-bit) MAC address 00:e0:81:28:67:9b
eth2: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
eth2: dma_rwctrl[763f0000] dma_mask[64-bit]
scsi11 : sata_sil
scsi12 : sata_sil
scsi13 : sata_sil
ata11: SATA max UDMA/100 mmio m1024@0xfeafec00 tf 0xfeafec80 irq 19
ata12: SATA max UDMA/100 mmio m1024@0xfeafec00 tf 0xfeafecc0 irq 19
ata13: SATA max UDMA/100 mmio m1024@0xfeafec00 tf 0xfeafee80 irq 19
ata14: SATA max UDMA/100 mmio m1024@0xfeafec00 tf 0xfeafeec0 irq 19
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata11: SATA link down (SStatus 0 SControl 310)
ata3.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata7.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata7.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb:
ata7.00: configured for UDMA/133
sdb1 sdb2
sd 2:0:0:0: [sdb] Attached SCSI disk
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/133
ata4: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
ata4: hotplug_status 0x22
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
ata4: EH complete
scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 3:0:0:0: Attached scsi generic sg3 type 0
sd 3:0:0:0: [sdc] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 3:0:0:0: [sdc] Write Protect is off
sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: unknown partition table
sd 3:0:0:0: [sdc] Attached SCSI disk
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata5.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata5.00: configured for UDMA/133
ata5: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
ata5: hotplug_status 0x11
ata5: hard resetting link
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: configured for UDMA/133
ata5: EH complete
scsi 4:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 4:0:0:0: Attached scsi generic sg4 type 0
sd 4:0:0:0: [sdd] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: unknown partition table
sd 4:0:0:0: [sdd] Attached SCSI disk
ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata6.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata6.00: configured for UDMA/133
ata6: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
ata6: hotplug_status 0x44
ata6: hard resetting link
ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: configured for UDMA/133
ata6: EH complete
scsi 5:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 5:0:0:0: Attached scsi generic sg5 type 0
sd 5:0:0:0: [sde] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 5:0:0:0: [sde] Write Protect is off
sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde:
scsi 6:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 6:0:0:0: Attached scsi generic sg6 type 0
sd 6:0:0:0: [sdf] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 6:0:0:0: [sdf] Write Protect is off
sd 6:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 6:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdf: unknown partition table
sd 6:0:0:0: [sdf] Attached SCSI disk
unknown partition table
sd 5:0:0:0: [sde] Attached SCSI disk
ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata8.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata8.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata8.00: configured for UDMA/133
ata8: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
ata8: hotplug_status 0x22
ata8: hard resetting link
ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata8.00: configured for UDMA/133
ata8: EH complete
scsi 7:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 7:0:0:0: Attached scsi generic sg7 type 0
sd 7:0:0:0: [sdg] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 7:0:0:0: [sdg] Write Protect is off
sd 7:0:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 7:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdg: unknown partition table
sd 7:0:0:0: [sdg] Attached SCSI disk
ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata9.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata9.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata9.00: configured for UDMA/133
ata9: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
ata9: hotplug_status 0x11
ata9: hard resetting link
ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata9.00: configured for UDMA/133
ata9: EH complete
scsi 8:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 8:0:0:0: Attached scsi generic sg8 type 0
sd 8:0:0:0: [sdh] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 8:0:0:0: [sdh] Write Protect is off
sd 8:0:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 8:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdh: unknown partition table
sd 8:0:0:0: [sdh] Attached SCSI disk
ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata10.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata10.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata10.00: configured for UDMA/133
ata10: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
ata10: hotplug_status 0x44
ata10: hard resetting link
ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata10.00: configured for UDMA/133
ata10: EH complete
scsi 9:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 9:0:0:0: Attached scsi generic sg9 type 0
sd 9:0:0:0: [sdi] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 9:0:0:0: [sdi] Write Protect is off
sd 9:0:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 9:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdi: unknown partition table
sd 9:0:0:0: [sdi] Attached SCSI disk
ata12: SATA link down (SStatus 0 SControl 310)
ata13: SATA link down (SStatus 0 SControl 310)
ata14: SATA link down (SStatus 0 SControl 310)
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
SELinux: 8192 avtab hash slots, 144734 rules.
SELinux: 8192 avtab hash slots, 144734 rules.
SELinux: 8 users, 12 roles, 2941 types, 136 bools, 1 sens, 1024 cats
SELinux: 75 classes, 144734 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev loop0, type squashfs), not configured for labeling
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1269547102.191:2): policy loaded auid=4294967295 ses=4294967295
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: generic_sse
generic_sse: 4476.000 MB/sec
xor: using function: generic_sse (4476.000 MB/sec)
async_tx: api initialized (async)
raid6: int64x1 1160 MB/s
raid6: int64x2 1414 MB/s
raid6: int64x4 1066 MB/s
raid6: int64x8 839 MB/s
raid6: sse2x1 1582 MB/s
raid6: sse2x2 2253 MB/s
raid6: sse2x4 2500 MB/s
raid6: using algorithm sse2x4 (2500 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
md: linear personality registered for level -1
device-mapper: multipath: version 1.1.0 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
e100 0000:03:08.0: firmware: requesting e100/d102e_ucode.bin
e100: eth1 NIC Link is Up 100 Mbps Full Duplex
tg3 0000:02:09.1: firmware: requesting tigon/tg3_tso.bin
tg3 0000:02:09.1: PME# disabled
tg3 0000:02:09.0: firmware: requesting tigon/tg3_tso.bin
tg3 0000:02:09.0: wake-up capability disabled by ACPI
tg3 0000:02:09.0: PME# disabled
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
Buffer I/O error on device fd0, logical block 0
end_request: I/O error, dev fd0, sector 0
Buffer I/O error on device fd0, logical block 0
EXT4-fs (sda1): barriers enabled
kjournald2 starting: pid 747, dev sda1:8, commit interval 5 seconds
EXT4-fs (sda1): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sda1): mounted filesystem with ordered data mode
SELinux: initialized (dev sda1, type ext4), uses xattr
EXT4-fs: mballoc: 0 blocks 0 reqs (0 success)
EXT4-fs: mballoc: 0 extents scanned, 0 goal hits, 0 2^N hits, 0 breaks, 0 lost
EXT4-fs: mballoc: 0 generated and it took 0
EXT4-fs: mballoc: 0 preallocated, 0 discarded
EXT4-fs (sda3): barriers enabled
kjournald2 starting: pid 756, dev sda3:8, commit interval 5 seconds
EXT4-fs (sda3): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sda3): mounted filesystem with ordered data mode
SELinux: initialized (dev sda3, type ext4), uses xattr
EXT4-fs: mballoc: 0 blocks 0 reqs (0 success)
EXT4-fs: mballoc: 0 extents scanned, 0 goal hits, 0 2^N hits, 0 breaks, 0 lost
EXT4-fs: mballoc: 0 generated and it took 0
EXT4-fs: mballoc: 0 preallocated, 0 discarded
EXT4-fs (sdb2): barriers enabled
kjournald2 starting: pid 765, dev sdb2:8, commit interval 5 seconds
EXT4-fs (sdb2): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sdb2): mounted filesystem with ordered data mode
SELinux: initialized (dev sdb2, type ext4), uses xattr
EXT4-fs: mballoc: 0 blocks 0 reqs (0 success)
EXT4-fs: mballoc: 0 extents scanned, 0 goal hits, 0 2^N hits, 0 breaks, 0 lost
EXT4-fs: mballoc: 0 generated and it took 0
EXT4-fs: mballoc: 0 preallocated, 0 discarded
EXT4-fs (sda3): barriers enabled
kjournald2 starting: pid 774, dev sda3:8, commit interval 5 seconds
EXT4-fs (sda3): internal journal on sda3:8
EXT4-fs (sda3): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sda3): mounted filesystem with ordered data mode
SELinux: initialized (dev sda3, type ext4), uses xattr
EXT4-fs (sda1): barriers enabled
kjournald2 starting: pid 776, dev sda1:8, commit interval 5 seconds
EXT4-fs (sda1): internal journal on sda1:8
EXT4-fs (sda1): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sda1): mounted filesystem with ordered data mode
SELinux: initialized (dev sda1, type ext4), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2097144k swap on /dev/sda2. Priority:-1 extents:1 across:2097144k
Adding 1951856k swap on /dev/sdb1. Priority:-2 extents:1 across:1951856k
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2010-03-25 20:25 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <201003230801.o2N81UKg009750@alien.loup.net>
2010-03-23 16:17 ` Regression: my systems can no longer boot from an ide hard drive Randy Dunlap
2010-03-24 0:20 ` Robert Hancock
2010-03-24 0:46 ` Mike Hayward
2010-03-24 23:47 ` Robert Hancock
2010-03-25 20:25 ` Mike Hayward
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).