* 2.6.35.9 bug shown in dmesg (fwd)
@ 2010-12-30 20:57 Russell Whitaker
2011-01-03 23:00 ` Stanislaw Gruszka
0 siblings, 1 reply; 8+ messages in thread
From: Russell Whitaker @ 2010-12-30 20:57 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1: Type: TEXT/PLAIN, Size: 1317 bytes --]
Hi
Since sending the email below found some more info:
Tried several kernels from 2.6.32.16 up - same problem.
If I build kernel using "ATA/ATAPI/MFM/RLL=y" and right choices in
sub-menu (and fstab with hd...) There is no problem.
Making change to "serial ATA (prod) and parallel ATA (experimental)=y"
the computer crashes during boot-up about 1/3 of the time.
Hardware:
Tyan mb s2466 Tiger MPX (2 cpu)
2 segate hd on primary ide
If you send me a patch, will try it and let you know what happens.
Thanks, Russ
---------- Forwarded message ----------
Date: Fri, 10 Dec 2010 23:11:43 -0800 (PST)
From: Russell Whitaker <russ@ashlandhome.net>
To: linux-kernel@vgerkernel.org
Subject: 2.6.35.9 bug shown in dmesg
Hi
The main partition boots 2.6.31.14 and it is rock solid.
Used it to build 2.6.35.9 which was installed on a separate partition, "test
partition". The config file for the build is a cut-down version of Slackware's
generic smp. The first 2 attachments are the config file and
output from ver_linux in this partition.
The 3rd attachment is output from ver_linux in the test partition.
The next 4 are the dmesg results from booting 4 times.
The last attachment is /proc/cpuinfo from the test partition.
Let me know if there is something I can try to give you more info.
Thanks,
Russ
[-- Attachment #2: config --]
[-- Type: TEXT/PLAIN, Size: 73206 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.35.9
# Tue Dec 7 19:40:47 2010
#
# CONFIG_64BIT is not set
CONFIG_X86_32=y
# CONFIG_X86_64 is not set
CONFIG_X86=y
CONFIG_INSTRUCTION_DECODER=y
CONFIG_OUTPUT_FORMAT="elf32-i386"
CONFIG_ARCH_DEFCONFIG="arch/x86/configs/i386_defconfig"
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
# CONFIG_NEED_DMA_MAP_STATE is not set
CONFIG_NEED_SG_DMA_LENGTH=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_GPIO=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
# CONFIG_GENERIC_TIME_VSYSCALL is not set
CONFIG_ARCH_HAS_CPU_RELAX=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y
CONFIG_HAVE_SETUP_PER_CPU_AREA=y
CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK=y
CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK=y
# CONFIG_HAVE_CPUMASK_OF_CPU_MAP is not set
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
# CONFIG_ZONE_DMA32 is not set
CONFIG_ARCH_POPULATES_NODE_MAP=y
# CONFIG_AUDIT_ARCH is not set
CONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=y
CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
CONFIG_HAVE_EARLY_RES=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_USE_GENERIC_SMP_HELPERS=y
CONFIG_X86_32_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_ARCH_HWEIGHT_CFLAGS="-fcall-saved-ecx -fcall-saved-edx"
CONFIG_KTIME_SCALAR=y
CONFIG_ARCH_CPU_PROBE_RELEASE=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_CONSTRUCTORS=y
#
# General setup
#
# CONFIG_EXPERIMENTAL is not set
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_CROSS_COMPILE=""
CONFIG_LOCALVERSION="-smp"
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_BZIP2=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_HAVE_KERNEL_LZO=y
# CONFIG_KERNEL_GZIP is not set
# CONFIG_KERNEL_BZIP2 is not set
CONFIG_KERNEL_LZMA=y
# CONFIG_KERNEL_LZO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
# CONFIG_TASKSTATS is not set
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
CONFIG_AUDIT_TREE=y
#
# RCU Subsystem
#
CONFIG_TREE_RCU=y
# CONFIG_TREE_PREEMPT_RCU is not set
# CONFIG_TINY_RCU is not set
# CONFIG_RCU_TRACE is not set
CONFIG_RCU_FANOUT=32
# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_RCU_FAST_NO_HZ is not set
# CONFIG_TREE_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=16
CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
# CONFIG_CGROUPS is not set
# CONFIG_SYSFS_DEPRECATED_V2 is not set
CONFIG_RELAY=y
CONFIG_NAMESPACES=y
CONFIG_UTS_NS=y
CONFIG_IPC_NS=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_RD_GZIP=y
CONFIG_RD_BZIP2=y
CONFIG_RD_LZMA=y
CONFIG_RD_LZO=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_PCSPKR_PLATFORM=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_HAVE_PERF_EVENTS=y
#
# Kernel Performance Events And Counters
#
CONFIG_PERF_EVENTS=y
# CONFIG_PERF_COUNTERS is not set
# CONFIG_DEBUG_PERF_USE_VMALLOC is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
CONFIG_SLUB_DEBUG=y
# CONFIG_COMPAT_BRK is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_OPTPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_HW_BREAKPOINT=y
CONFIG_HAVE_MIXED_BREAKPOINTS_REGS=y
CONFIG_HAVE_USER_RETURN_NOTIFIER=y
#
# GCOV-based kernel profiling
#
CONFIG_SLOW_WORK=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_FORCE_LOAD=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
CONFIG_LBDAF=y
CONFIG_BLK_DEV_BSG=y
# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
# CONFIG_INLINE_SPIN_TRYLOCK is not set
# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK is not set
# CONFIG_INLINE_SPIN_LOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
CONFIG_INLINE_SPIN_UNLOCK=y
# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
# CONFIG_INLINE_READ_TRYLOCK is not set
# CONFIG_INLINE_READ_LOCK is not set
# CONFIG_INLINE_READ_LOCK_BH is not set
# CONFIG_INLINE_READ_LOCK_IRQ is not set
# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
CONFIG_INLINE_READ_UNLOCK=y
# CONFIG_INLINE_READ_UNLOCK_BH is not set
CONFIG_INLINE_READ_UNLOCK_IRQ=y
# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
# CONFIG_INLINE_WRITE_TRYLOCK is not set
# CONFIG_INLINE_WRITE_LOCK is not set
# CONFIG_INLINE_WRITE_LOCK_BH is not set
# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
CONFIG_INLINE_WRITE_UNLOCK=y
# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
CONFIG_MUTEX_SPIN_ON_OWNER=y
CONFIG_FREEZER=y
#
# Processor type and features
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_SMP=y
# CONFIG_SPARSE_IRQ is not set
# CONFIG_X86_MPPARSE is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_EXTENDED_PLATFORM is not set
CONFIG_X86_SUPPORTS_MEMORY_FAILURE=y
CONFIG_SCHED_OMIT_FRAME_POINTER=y
# CONFIG_PARAVIRT_GUEST is not set
# CONFIG_NO_BOOTMEM is not set
CONFIG_MEMTEST=y
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_MPSC is not set
# CONFIG_MCORE2 is not set
# CONFIG_MATOM is not set
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_GENERIC=y
CONFIG_X86_CPU=y
CONFIG_X86_INTERNODE_CACHE_SHIFT=6
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_XADD=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_TSC=y
CONFIG_X86_CMOV=y
CONFIG_X86_MINIMUM_CPU_FAMILY=4
CONFIG_X86_DEBUGCTLMSR=y
CONFIG_CPU_SUP_INTEL=y
CONFIG_CPU_SUP_CYRIX_32=y
CONFIG_CPU_SUP_AMD=y
CONFIG_CPU_SUP_CENTAUR=y
CONFIG_CPU_SUP_TRANSMETA_32=y
CONFIG_CPU_SUP_UMC_32=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_DMI=y
# CONFIG_IOMMU_HELPER is not set
# CONFIG_IOMMU_API is not set
CONFIG_NR_CPUS=2
CONFIG_SCHED_SMT=y
# CONFIG_SCHED_MC is not set
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
# CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS is not set
CONFIG_X86_MCE=y
# CONFIG_X86_MCE_INTEL is not set
CONFIG_X86_MCE_AMD=y
# CONFIG_X86_ANCIENT_MCE is not set
CONFIG_X86_MCE_THRESHOLD=y
# CONFIG_X86_MCE_INJECT is not set
CONFIG_VM86=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_X86_REBOOTFIXUPS is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
CONFIG_X86_CPUID=m
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_HIGHMEM=y
# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
CONFIG_ILLEGAL_POINTER_VALUE=0
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_ARCH_SUPPORTS_MEMORY_FAILURE=y
# CONFIG_MEMORY_FAILURE is not set
CONFIG_HIGHPTE=y
# CONFIG_X86_CHECK_BIOS_CORRUPTION is not set
CONFIG_X86_RESERVE_LOW_64K=y
CONFIG_MATH_EMULATION=y
CONFIG_MTRR=y
CONFIG_MTRR_SANITIZER=y
CONFIG_MTRR_SANITIZER_ENABLE_DEFAULT=0
CONFIG_MTRR_SANITIZER_SPARE_REG_NR_DEFAULT=1
CONFIG_X86_PAT=y
CONFIG_ARCH_USES_PG_UNCACHED=y
# CONFIG_EFI is not set
CONFIG_SECCOMP=y
CONFIG_CC_STACKPROTECTOR=y
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_SCHED_HRTICK=y
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x1000000
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_ALIGN=0x100000
CONFIG_HOTPLUG_CPU=y
CONFIG_COMPAT_VDSO=y
# CONFIG_CMDLINE_BOOL is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
#
# Power management and ACPI options
#
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND_NVS=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
# CONFIG_HIBERNATION is not set
CONFIG_PM_RUNTIME=y
CONFIG_PM_OPS=y
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_PROCFS=y
CONFIG_ACPI_PROCFS_POWER=y
CONFIG_ACPI_POWER_METER=m
CONFIG_ACPI_SYSFS_POWER=y
CONFIG_ACPI_PROC_EVENT=y
# CONFIG_ACPI_AC is not set
# CONFIG_ACPI_BATTERY is not set
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
CONFIG_ACPI_FAN=m
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=m
# CONFIG_ACPI_CUSTOM_DSDT is not set
CONFIG_ACPI_BLACKLIST_YEAR=2001
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_PCI_SLOT=m
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=m
# CONFIG_ACPI_SBS is not set
CONFIG_ACPI_HED=m
CONFIG_ACPI_APEI=y
CONFIG_ACPI_APEI_GHES=m
# CONFIG_SFI is not set
CONFIG_X86_APM_BOOT=y
CONFIG_APM=m
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_ALLOW_INTS is not set
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=m
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
#
# CPUFreq processor drivers
#
CONFIG_X86_PCC_CPUFREQ=m
CONFIG_X86_ACPI_CPUFREQ=m
CONFIG_X86_POWERNOW_K6=m
CONFIG_X86_POWERNOW_K7=m
CONFIG_X86_POWERNOW_K7_ACPI=y
CONFIG_X86_POWERNOW_K8=m
CONFIG_X86_GX_SUSPMOD=m
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=m
CONFIG_X86_P4_CLOCKMOD=m
CONFIG_X86_LONGRUN=m
CONFIG_X86_LONGHAUL=m
#
# shared options
#
CONFIG_X86_SPEEDSTEP_LIB=m
CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK=y
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_IDLE_GOV_MENU=y
#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
# CONFIG_PCI_GOOLPC is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCI_CNB20LE_QUIRK is not set
# CONFIG_PCIEPORTBUS is not set
CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
CONFIG_PCI_STUB=m
CONFIG_HT_IRQ=y
# CONFIG_PCI_IOV is not set
CONFIG_PCI_IOAPIC=y
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
# CONFIG_OLPC is not set
CONFIG_K8_NB=y
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_HAVE_AOUT=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
CONFIG_HAVE_ATOMIC_IOMAP=y
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=y
CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=m
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
CONFIG_INET_LRO=y
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
# CONFIG_IPV6_ROUTER_PREF is not set
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_INET6_XFRM_MODE_BEET=m
CONFIG_IPV6_SIT=m
CONFIG_IPV6_NDISC_NODETYPE=y
CONFIG_IPV6_TUNNEL=m
# CONFIG_NETLABEL is not set
# CONFIG_NETWORK_SECMARK is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_NETFILTER_ADVANCED=y
#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NF_CONNTRACK=m
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_ZONES=y
# CONFIG_NF_CONNTRACK_EVENTS is not set
CONFIG_NF_CT_PROTO_GRE=m
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_FTP=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
CONFIG_NETFILTER_XTABLES=m
#
# Xtables combined modules
#
CONFIG_NETFILTER_XT_MARK=m
CONFIG_NETFILTER_XT_CONNMARK=m
#
# Xtables targets
#
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_CT=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
CONFIG_NETFILTER_XT_TARGET_HL=m
CONFIG_NETFILTER_XT_TARGET_LED=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
CONFIG_NETFILTER_XT_TARGET_RATEEST=m
CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
#
# Xtables matches
#
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_HELPER=m
CONFIG_NETFILTER_XT_MATCH_HL=m
CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
CONFIG_NETFILTER_XT_MATCH_RATEEST=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_RECENT=m
CONFIG_NETFILTER_XT_MATCH_STATE=m
CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
CONFIG_IP_VS=m
# CONFIG_IP_VS_DEBUG is not set
CONFIG_IP_VS_TAB_BITS=12
#
# IPVS transport protocol load balancing support
#
CONFIG_IP_VS_PROTO_TCP=y
CONFIG_IP_VS_PROTO_UDP=y
CONFIG_IP_VS_PROTO_AH_ESP=y
CONFIG_IP_VS_PROTO_ESP=y
CONFIG_IP_VS_PROTO_AH=y
CONFIG_IP_VS_PROTO_SCTP=y
#
# IPVS scheduler
#
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m
#
# IPVS application helper
#
CONFIG_IP_VS_FTP=m
#
# IP: Netfilter Configuration
#
CONFIG_NF_DEFRAG_IPV4=m
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_NF_NAT=m
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_NF_NAT_PROTO_GRE=m
CONFIG_NF_NAT_PROTO_UDPLITE=m
CONFIG_NF_NAT_FTP=m
CONFIG_NF_NAT_IRC=m
CONFIG_NF_NAT_TFTP=m
CONFIG_NF_NAT_AMANDA=m
CONFIG_NF_NAT_PPTP=m
CONFIG_NF_NAT_H323=m
CONFIG_NF_NAT_SIP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_SECURITY=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
#
# IPv6: Netfilter Configuration
#
CONFIG_NF_CONNTRACK_IPV6=m
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
CONFIG_IP6_NF_SECURITY=m
CONFIG_ATM=m
# CONFIG_ATM_CLIP is not set
# CONFIG_ATM_LANE is not set
# CONFIG_ATM_BR2684 is not set
# CONFIG_L2TP is not set
CONFIG_STP=m
CONFIG_GARP=m
# CONFIG_BRIDGE is not set
CONFIG_VLAN_8021Q=m
CONFIG_VLAN_8021Q_GVRP=y
# CONFIG_DECNET is not set
CONFIG_LLC=m
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
CONFIG_ATALK=m
CONFIG_DEV_APPLETALK=m
CONFIG_IPDDP=m
CONFIG_IPDDP_ENCAP=y
CONFIG_IPDDP_DECAP=y
CONFIG_PHONET=m
CONFIG_NET_SCHED=y
#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_ATM=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_MULTIQ=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_DRR=m
CONFIG_NET_SCH_INGRESS=m
#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=m
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
# CONFIG_CLS_U32_PERF is not set
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_CLS_FLOW=m
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=m
CONFIG_NET_EMATCH_NBYTE=m
CONFIG_NET_EMATCH_U32=m
CONFIG_NET_EMATCH_META=m
CONFIG_NET_EMATCH_TEXT=m
CONFIG_NET_CLS_ACT=y
CONFIG_NET_ACT_POLICE=y
CONFIG_NET_ACT_GACT=m
CONFIG_GACT_PROB=y
CONFIG_NET_ACT_MIRRED=m
CONFIG_NET_ACT_IPT=m
CONFIG_NET_ACT_NAT=m
CONFIG_NET_ACT_PEDIT=m
CONFIG_NET_ACT_SIMP=m
CONFIG_NET_ACT_SKBEDIT=m
# CONFIG_NET_CLS_IND is not set
CONFIG_NET_SCH_FIFO=y
# CONFIG_DCB is not set
CONFIG_RPS=y
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
CONFIG_CAN=m
CONFIG_CAN_RAW=m
CONFIG_CAN_BCM=m
#
# CAN Device Drivers
#
CONFIG_CAN_VCAN=m
CONFIG_CAN_DEV=m
# CONFIG_CAN_CALC_BITTIMING is not set
CONFIG_CAN_SJA1000=m
CONFIG_CAN_SJA1000_PLATFORM=m
CONFIG_CAN_EMS_PCI=m
CONFIG_CAN_KVASER_PCI=m
CONFIG_CAN_PLX_PCI=m
#
# CAN USB interfaces
#
CONFIG_CAN_EMS_USB=m
# CONFIG_CAN_DEBUG_DEVICES is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
CONFIG_FIB_RULES=y
CONFIG_WIRELESS=y
CONFIG_WEXT_CORE=y
CONFIG_WEXT_PROC=y
CONFIG_CFG80211=m
# CONFIG_NL80211_TESTMODE is not set
# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
# CONFIG_CFG80211_REG_DEBUG is not set
CONFIG_CFG80211_DEFAULT_PS=y
# CONFIG_CFG80211_INTERNAL_REGDB is not set
CONFIG_CFG80211_WEXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
CONFIG_LIB80211=m
# CONFIG_LIB80211_DEBUG is not set
CONFIG_MAC80211=m
CONFIG_MAC80211_HAS_RC=y
CONFIG_MAC80211_RC_MINSTREL=y
# CONFIG_MAC80211_RC_DEFAULT_PID is not set
CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
CONFIG_MAC80211_RC_DEFAULT="minstrel"
CONFIG_MAC80211_LEDS=y
# CONFIG_MAC80211_DEBUG_MENU is not set
CONFIG_WIMAX=m
CONFIG_WIMAX_DEBUG_LEVEL=8
CONFIG_RFKILL=m
CONFIG_RFKILL_LEDS=y
CONFIG_RFKILL_INPUT=y
# CONFIG_CAIF is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
CONFIG_MTD=m
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_TESTS=m
CONFIG_MTD_CONCAT=m
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_REDBOOT_PARTS=m
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
CONFIG_MTD_AR7_PARTS=m
#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=m
CONFIG_HAVE_MTD_OTP=y
CONFIG_MTD_BLKDEVS=m
CONFIG_MTD_BLOCK=m
CONFIG_MTD_BLOCK_RO=m
CONFIG_FTL=m
CONFIG_NFTL=m
CONFIG_NFTL_RW=y
CONFIG_INFTL=m
CONFIG_RFD_FTL=m
CONFIG_SSFDC=m
CONFIG_MTD_OOPS=m
#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=m
CONFIG_MTD_JEDECPROBE=m
CONFIG_MTD_GEN_PROBE=m
CONFIG_MTD_CFI_ADV_OPTIONS=y
CONFIG_MTD_CFI_NOSWAP=y
# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
CONFIG_MTD_CFI_GEOMETRY=y
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
CONFIG_MTD_MAP_BANK_WIDTH_8=y
CONFIG_MTD_MAP_BANK_WIDTH_16=y
CONFIG_MTD_MAP_BANK_WIDTH_32=y
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
CONFIG_MTD_CFI_I4=y
CONFIG_MTD_CFI_I8=y
CONFIG_MTD_OTP=y
CONFIG_MTD_CFI_INTELEXT=m
CONFIG_MTD_CFI_AMDSTD=m
CONFIG_MTD_CFI_STAA=m
CONFIG_MTD_CFI_UTIL=m
CONFIG_MTD_RAM=m
CONFIG_MTD_ROM=m
CONFIG_MTD_ABSENT=m
#
# Mapping drivers for chip access
#
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=m
# CONFIG_MTD_PHYSMAP_COMPAT is not set
CONFIG_MTD_SC520CDP=m
CONFIG_MTD_NETSC520=m
CONFIG_MTD_TS5500=m
CONFIG_MTD_SBC_GXX=m
CONFIG_MTD_AMD76XROM=m
CONFIG_MTD_ICHXROM=m
CONFIG_MTD_ESB2ROM=m
CONFIG_MTD_CK804XROM=m
CONFIG_MTD_SCB2_FLASH=m
CONFIG_MTD_NETtel=m
CONFIG_MTD_L440GX=m
CONFIG_MTD_PCI=m
CONFIG_MTD_GPIO_ADDR=m
CONFIG_MTD_INTEL_VR_NOR=m
CONFIG_MTD_PLATRAM=m
#
# Self-contained MTD device drivers
#
CONFIG_MTD_PMC551=m
CONFIG_MTD_PMC551_BUGFIX=y
# CONFIG_MTD_PMC551_DEBUG is not set
CONFIG_MTD_SLRAM=m
CONFIG_MTD_PHRAM=m
CONFIG_MTD_MTDRAM=m
CONFIG_MTDRAM_TOTAL_SIZE=4096
CONFIG_MTDRAM_ERASE_SIZE=128
CONFIG_MTD_BLOCK2MTD=m
#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
CONFIG_MTD_DOC2001PLUS=m
CONFIG_MTD_DOCPROBE=m
CONFIG_MTD_DOCECC=m
CONFIG_MTD_DOCPROBE_ADVANCED=y
CONFIG_MTD_DOCPROBE_ADDRESS=0x0000
CONFIG_MTD_DOCPROBE_HIGH=y
CONFIG_MTD_DOCPROBE_55AA=y
CONFIG_MTD_NAND_ECC=m
CONFIG_MTD_NAND_ECC_SMC=y
CONFIG_MTD_NAND=m
CONFIG_MTD_NAND_VERIFY_WRITE=y
CONFIG_MTD_SM_COMMON=m
CONFIG_MTD_NAND_MUSEUM_IDS=y
CONFIG_MTD_NAND_DENALI=m
CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR=0xFF108018
CONFIG_MTD_NAND_IDS=m
CONFIG_MTD_NAND_RICOH=m
CONFIG_MTD_NAND_CAFE=m
CONFIG_MTD_NAND_CS553X=m
CONFIG_MTD_NAND_NANDSIM=m
CONFIG_MTD_NAND_PLATFORM=m
CONFIG_MTD_ALAUDA=m
CONFIG_MTD_ONENAND=m
CONFIG_MTD_ONENAND_VERIFY_WRITE=y
CONFIG_MTD_ONENAND_GENERIC=m
CONFIG_MTD_ONENAND_OTP=y
CONFIG_MTD_ONENAND_2X_PROGRAM=y
CONFIG_MTD_ONENAND_SIM=m
#
# LPDDR flash memory drivers
#
CONFIG_MTD_LPDDR=m
CONFIG_MTD_QINFO_PROBE=m
#
# UBI - Unsorted block images
#
CONFIG_MTD_UBI=m
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_RESERVE=1
CONFIG_MTD_UBI_GLUEBI=m
#
# UBI debugging options
#
# CONFIG_MTD_UBI_DEBUG is not set
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_SERIAL=m
# CONFIG_PARPORT_GSC is not set
CONFIG_PARPORT_AX88796=m
CONFIG_PARPORT_1284=y
CONFIG_PARPORT_NOT_PC=y
CONFIG_PNP=y
CONFIG_PNP_DEBUG_MESSAGES=y
#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=m
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
# CONFIG_BLK_DEV_DRBD is not set
CONFIG_BLK_DEV_NBD=m
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=16384
# CONFIG_BLK_DEV_XIP is not set
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_BLK_DEV_HD is not set
# CONFIG_MISC_DEVICES is not set
CONFIG_EEPROM_93CX6=m
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# SCSI device support
#
CONFIG_SCSI_MOD=y
CONFIG_RAID_ATTRS=y
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=m
CONFIG_SCSI_ISCSI_ATTRS=y
CONFIG_SCSI_SAS_ATTRS=y
CONFIG_SCSI_SAS_LIBSAS=y
CONFIG_SCSI_SAS_ATA=y
CONFIG_SCSI_SAS_HOST_SMP=y
# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
CONFIG_SCSI_SRP_ATTRS=m
# CONFIG_SCSI_LOWLEVEL is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_ATA_ACPI=y
# CONFIG_SATA_PMP is not set
#
# Controllers with non-SFF native interface
#
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_AHCI_PLATFORM is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_SATA_SIL24 is not set
CONFIG_ATA_SFF=y
#
# SFF controllers with custom DMA interface
#
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
CONFIG_ATA_BMDMA=y
#
# SATA SFF controllers with BMDMA
#
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_SVW is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
#
# PATA SFF controllers with BMDMA
#
# CONFIG_PATA_ALI is not set
CONFIG_PATA_AMD=y
# CONFIG_PATA_ARTOP is not set
CONFIG_PATA_ATIIXP=y
# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CS5536 is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RDC is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SCH is not set
# CONFIG_PATA_SERVERWORKS is not set
CONFIG_PATA_SIL680=y
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
#
# PIO-only SFF controllers
#
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_RZ1000 is not set
#
# Generic fallback / legacy drivers
#
CONFIG_PATA_ACPI=y
CONFIG_ATA_GENERIC=y
# CONFIG_MD is not set
CONFIG_FUSION=y
CONFIG_FUSION_SPI=m
CONFIG_FUSION_FC=m
CONFIG_FUSION_SAS=m
CONFIG_FUSION_MAX_SGE=128
CONFIG_FUSION_CTL=m
# CONFIG_FUSION_LOGGING is not set
#
# IEEE 1394 (FireWire) support
#
#
# You can enable one or both FireWire driver stacks.
#
#
# The newer stack is recommended.
#
# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=m
CONFIG_IEEE1394_OHCI1394=m
CONFIG_IEEE1394_PCILYNX=m
CONFIG_IEEE1394_SBP2=m
# CONFIG_IEEE1394_ETH1394_ROM_ENTRY is not set
CONFIG_IEEE1394_RAWIO=m
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_DV1394=m
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_I2O is not set
# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
CONFIG_IFB=m
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_VETH is not set
# CONFIG_NET_SB1000 is not set
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=m
#
# MII PHY device drivers
#
# CONFIG_MARVELL_PHY is not set
# CONFIG_DAVICOM_PHY is not set
# CONFIG_QSEMI_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_VITESSE_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_BROADCOM_PHY is not set
# CONFIG_ICPLUS_PHY is not set
CONFIG_REALTEK_PHY=m
# CONFIG_NATIONAL_PHY is not set
# CONFIG_STE10XP is not set
# CONFIG_LSI_ET1011C_PHY is not set
# CONFIG_MICREL_PHY is not set
# CONFIG_MDIO_BITBANG is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
CONFIG_NET_VENDOR_3COM=y
CONFIG_VORTEX=y
# CONFIG_TYPHOON is not set
# CONFIG_ETHOC is not set
# CONFIG_DNET is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_NET_PCI is not set
# CONFIG_B44 is not set
# CONFIG_KS8842 is not set
# CONFIG_KS8851_MLL is not set
# CONFIG_NET_POCKET is not set
# CONFIG_ATL2 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
CONFIG_WLAN=y
# CONFIG_LIBERTAS_THINFIRM is not set
# CONFIG_AIRO is not set
# CONFIG_ATMEL is not set
# CONFIG_AT76C50X_USB is not set
# CONFIG_USB_ZD1201 is not set
CONFIG_RTL8187=m
CONFIG_RTL8187_LEDS=y
# CONFIG_MAC80211_HWSIM is not set
# CONFIG_ATH_COMMON is not set
# CONFIG_B43 is not set
# CONFIG_B43LEGACY is not set
# CONFIG_HOSTAP is not set
# CONFIG_IPW2100 is not set
# CONFIG_IPW2200 is not set
# CONFIG_IWLWIFI is not set
# CONFIG_LIBERTAS is not set
# CONFIG_HERMES is not set
# CONFIG_RT2X00 is not set
#
# WiMAX Wireless Broadband devices
#
#
# Enable MMC support to see WiMAX SDIO drivers
#
# CONFIG_WIMAX_I2400M_USB is not set
#
# USB Network Adapters
#
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_HSO is not set
# CONFIG_USB_CDC_PHONET is not set
# CONFIG_USB_IPHETH is not set
# CONFIG_WAN is not set
# CONFIG_ATM_DRIVERS is not set
# CONFIG_FDDI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_VMXNET3 is not set
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
CONFIG_INPUT_FF_MEMLESS=y
CONFIG_INPUT_POLLDEV=m
CONFIG_INPUT_SPARSEKMAP=m
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
CONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ADP5588=m
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_LKKBD is not set
CONFIG_KEYBOARD_GPIO=m
CONFIG_KEYBOARD_TCA6416=m
CONFIG_KEYBOARD_MATRIX=m
CONFIG_KEYBOARD_LM8323=m
CONFIG_KEYBOARD_MAX7359=m
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_KEYBOARD_OPENCORES=m
CONFIG_KEYBOARD_STOWAWAY=m
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_ELANTECH is not set
CONFIG_MOUSE_PS2_SENTELIC=y
CONFIG_MOUSE_PS2_TOUCHKIT=y
CONFIG_MOUSE_SERIAL=m
CONFIG_MOUSE_APPLETOUCH=m
CONFIG_MOUSE_BCM5974=m
CONFIG_MOUSE_VSXXXAA=m
CONFIG_MOUSE_GPIO=m
CONFIG_MOUSE_SYNAPTICS_I2C=m
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_AD714X=y
# CONFIG_INPUT_AD714X_I2C is not set
CONFIG_INPUT_PCSPKR=m
# CONFIG_INPUT_APANEL is not set
# CONFIG_INPUT_WISTRON_BTNS is not set
# CONFIG_INPUT_ATLAS_BTNS is not set
# CONFIG_INPUT_ATI_REMOTE is not set
# CONFIG_INPUT_ATI_REMOTE2 is not set
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_UINPUT is not set
# CONFIG_INPUT_WINBOND_CIR is not set
# CONFIG_INPUT_GPIO_ROTARY_ENCODER is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
# CONFIG_SERIO_CT82C710 is not set
CONFIG_SERIO_PARKBD=m
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
# CONFIG_SERIO_ALTERA_PS2 is not set
CONFIG_GAMEPORT=m
CONFIG_GAMEPORT_NS558=m
# CONFIG_GAMEPORT_L4 is not set
CONFIG_GAMEPORT_EMU10K1=m
CONFIG_GAMEPORT_FM801=m
#
# Character devices
#
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_JSM=m
CONFIG_SERIAL_TIMBERDALE=m
CONFIG_SERIAL_ALTERA_JTAGUART=m
CONFIG_SERIAL_ALTERA_UART=m
CONFIG_SERIAL_ALTERA_UART_MAXPORTS=4
CONFIG_SERIAL_ALTERA_UART_BAUDRATE=115200
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=32
CONFIG_PRINTER=m
CONFIG_LP_CONSOLE=y
CONFIG_PPDEV=m
CONFIG_IPMI_HANDLER=m
# CONFIG_IPMI_PANIC_EVENT is not set
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_TIMERIOMEM=m
CONFIG_HW_RANDOM_INTEL=m
CONFIG_HW_RANDOM_AMD=m
# CONFIG_HW_RANDOM_GEODE is not set
# CONFIG_HW_RANDOM_VIA is not set
CONFIG_NVRAM=m
CONFIG_R3964=m
# CONFIG_APPLICOM is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
# CONFIG_NSC_GPIO is not set
# CONFIG_CS5535_GPIO is not set
CONFIG_RAW_DRIVER=m
CONFIG_MAX_RAW_DEVS=256
CONFIG_HPET=y
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m
CONFIG_DEVPORT=y
CONFIG_RAMOOPS=m
CONFIG_I2C=m
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=m
CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_SMBUS=m
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCA=m
#
# I2C Hardware Bus support
#
#
# PC SMBus host controller drivers
#
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD8111=m
CONFIG_I2C_I801=m
CONFIG_I2C_ISCH=m
CONFIG_I2C_PIIX4=m
CONFIG_I2C_NFORCE2=m
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
CONFIG_I2C_VIAPRO=m
#
# ACPI drivers
#
CONFIG_I2C_SCMI=m
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
CONFIG_I2C_GPIO=m
CONFIG_I2C_PCA_PLATFORM=m
CONFIG_I2C_SIMTEC=m
#
# External I2C/SMBus adapter drivers
#
CONFIG_I2C_PARPORT=m
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_TINY_USB=m
#
# Other I2C/SMBus bus drivers
#
CONFIG_SCx200_ACB=m
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_SPI is not set
#
# PPS support
#
CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_DEBUG_GPIO is not set
CONFIG_GPIO_MAX730X=m
#
# Memory mapped GPIO expanders:
#
CONFIG_GPIO_IT8761E=m
CONFIG_GPIO_SCH=m
#
# I2C GPIO expanders:
#
CONFIG_GPIO_MAX7300=m
CONFIG_GPIO_MAX732X=m
CONFIG_GPIO_PCA953X=m
CONFIG_GPIO_PCF857X=m
CONFIG_GPIO_ADP5588=m
#
# PCI GPIO expanders:
#
CONFIG_GPIO_CS5535=m
# CONFIG_GPIO_LANGWELL is not set
CONFIG_GPIO_RDC321X=m
#
# SPI GPIO expanders:
#
#
# AC97 GPIO expanders:
#
#
# MODULbus GPIO expanders:
#
CONFIG_W1=m
CONFIG_W1_CON=y
#
# 1-wire Bus Masters
#
CONFIG_W1_MASTER_MATROX=m
CONFIG_W1_MASTER_DS2490=m
CONFIG_W1_MASTER_GPIO=m
#
# 1-wire Slaves
#
CONFIG_W1_SLAVE_THERM=m
CONFIG_W1_SLAVE_SMEM=m
CONFIG_W1_SLAVE_DS2431=m
CONFIG_W1_SLAVE_DS2433=m
CONFIG_W1_SLAVE_DS2433_CRC=y
CONFIG_W1_SLAVE_DS2760=m
CONFIG_W1_SLAVE_BQ27000=m
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
CONFIG_PDA_POWER=m
CONFIG_TEST_POWER=m
CONFIG_BATTERY_DS2760=m
CONFIG_BATTERY_DS2782=m
CONFIG_BATTERY_BQ27x00=m
CONFIG_BATTERY_MAX17040=m
CONFIG_HWMON=m
CONFIG_HWMON_VID=m
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Native drivers
#
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASC7621 is not set
# CONFIG_SENSORS_K10TEMP is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHMD is not set
# CONFIG_SENSORS_G760A is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IBMAEM is not set
# CONFIG_SENSORS_IBMPEX is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM73 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_LM93 is not set
# CONFIG_SENSORS_LM95241 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_SHT15 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_EMC1403 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_VIA_CPUTEMP is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT8231 is not set
CONFIG_SENSORS_W83781D=m
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_HDAPS is not set
# CONFIG_SENSORS_LIS3_I2C is not set
# CONFIG_SENSORS_APPLESMC is not set
#
# ACPI drivers
#
# CONFIG_SENSORS_LIS3LV02D is not set
CONFIG_THERMAL=m
CONFIG_THERMAL_HWMON=y
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set
CONFIG_MFD_SUPPORT=y
CONFIG_MFD_CORE=m
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_UCB1400_CORE is not set
# CONFIG_TPS65010 is not set
# CONFIG_TPS6507X is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_ABX500_CORE is not set
# CONFIG_MFD_TIMBERDALE is not set
CONFIG_LPC_SCH=m
CONFIG_MFD_RDC321X=m
# CONFIG_MFD_JANZ_CMODIO is not set
# CONFIG_REGULATOR is not set
CONFIG_MEDIA_SUPPORT=m
#
# Multimedia core support
#
CONFIG_VIDEO_DEV=m
CONFIG_VIDEO_V4L2_COMMON=m
CONFIG_VIDEO_ALLOW_V4L1=y
CONFIG_VIDEO_V4L1_COMPAT=y
CONFIG_DVB_CORE=m
CONFIG_VIDEO_MEDIA=m
#
# Multimedia drivers
#
CONFIG_VIDEO_SAA7146=m
CONFIG_VIDEO_SAA7146_VV=m
CONFIG_IR_CORE=m
CONFIG_VIDEO_IR=m
CONFIG_RC_MAP=m
CONFIG_IR_NEC_DECODER=m
CONFIG_IR_RC5_DECODER=m
CONFIG_IR_RC6_DECODER=m
CONFIG_IR_JVC_DECODER=m
CONFIG_IR_SONY_DECODER=m
CONFIG_IR_IMON=m
CONFIG_MEDIA_ATTACH=y
CONFIG_MEDIA_TUNER=m
# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
CONFIG_MEDIA_TUNER_SIMPLE=m
CONFIG_MEDIA_TUNER_TDA8290=m
CONFIG_MEDIA_TUNER_TDA827X=m
CONFIG_MEDIA_TUNER_TDA18271=m
CONFIG_MEDIA_TUNER_TDA9887=m
CONFIG_MEDIA_TUNER_TEA5761=m
CONFIG_MEDIA_TUNER_TEA5767=m
CONFIG_MEDIA_TUNER_MT20XX=m
CONFIG_MEDIA_TUNER_MT2131=m
CONFIG_MEDIA_TUNER_XC2028=m
CONFIG_MEDIA_TUNER_XC5000=m
CONFIG_MEDIA_TUNER_MXL5007T=m
CONFIG_MEDIA_TUNER_MC44S803=m
CONFIG_VIDEO_V4L2=m
CONFIG_VIDEO_V4L1=m
CONFIG_VIDEOBUF_GEN=m
CONFIG_VIDEOBUF_DMA_SG=m
CONFIG_VIDEOBUF_VMALLOC=m
CONFIG_VIDEOBUF_DVB=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_TVEEPROM=m
CONFIG_VIDEO_TUNER=m
CONFIG_V4L2_MEM2MEM_DEV=m
CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
# CONFIG_VIDEO_HELPER_CHIPS_AUTO is not set
CONFIG_VIDEO_IR_I2C=m
#
# Encoders/decoders and other helper chips
#
#
# Audio decoders
#
CONFIG_VIDEO_TVAUDIO=m
CONFIG_VIDEO_TDA7432=m
CONFIG_VIDEO_TDA9840=m
CONFIG_VIDEO_TDA9875=m
CONFIG_VIDEO_TEA6415C=m
CONFIG_VIDEO_TEA6420=m
CONFIG_VIDEO_MSP3400=m
CONFIG_VIDEO_CS5345=m
CONFIG_VIDEO_CS53L32A=m
CONFIG_VIDEO_M52790=m
CONFIG_VIDEO_WM8775=m
CONFIG_VIDEO_WM8739=m
CONFIG_VIDEO_VP27SMPX=m
#
# RDS decoders
#
CONFIG_VIDEO_SAA6588=m
#
# Video decoders
#
CONFIG_VIDEO_ADV7180=m
CONFIG_VIDEO_BT819=m
CONFIG_VIDEO_BT856=m
CONFIG_VIDEO_BT866=m
CONFIG_VIDEO_KS0127=m
CONFIG_VIDEO_OV7670=m
CONFIG_VIDEO_MT9V011=m
CONFIG_VIDEO_TCM825X=m
CONFIG_VIDEO_SAA7110=m
CONFIG_VIDEO_SAA711X=m
CONFIG_VIDEO_SAA717X=m
CONFIG_VIDEO_SAA7191=m
CONFIG_VIDEO_TVP514X=m
CONFIG_VIDEO_TVP5150=m
CONFIG_VIDEO_TVP7002=m
CONFIG_VIDEO_VPX3220=m
#
# Video and audio decoders
#
CONFIG_VIDEO_CX25840=m
#
# MPEG video encoders
#
CONFIG_VIDEO_CX2341X=m
#
# Video encoders
#
CONFIG_VIDEO_SAA7127=m
CONFIG_VIDEO_SAA7185=m
CONFIG_VIDEO_ADV7170=m
CONFIG_VIDEO_ADV7175=m
CONFIG_VIDEO_THS7303=m
CONFIG_VIDEO_ADV7343=m
CONFIG_VIDEO_AK881X=m
#
# Video improvement chips
#
CONFIG_VIDEO_UPD64031A=m
CONFIG_VIDEO_UPD64083=m
CONFIG_VIDEO_VIVI=m
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_BT848_DVB=y
CONFIG_VIDEO_BWQCAM=m
CONFIG_VIDEO_W9966=m
CONFIG_VIDEO_CPIA=m
CONFIG_VIDEO_CPIA_PP=m
CONFIG_VIDEO_CPIA_USB=m
CONFIG_VIDEO_CPIA2=m
CONFIG_VIDEO_SAA5246A=m
CONFIG_VIDEO_SAA5249=m
CONFIG_VIDEO_ZORAN=m
CONFIG_VIDEO_ZORAN_DC30=m
CONFIG_VIDEO_ZORAN_ZR36060=m
CONFIG_VIDEO_ZORAN_BUZ=m
CONFIG_VIDEO_ZORAN_DC10=m
CONFIG_VIDEO_ZORAN_LML33=m
CONFIG_VIDEO_ZORAN_LML33R10=m
CONFIG_VIDEO_SAA7134=m
CONFIG_VIDEO_SAA7134_ALSA=m
CONFIG_VIDEO_SAA7134_DVB=m
CONFIG_VIDEO_MXB=m
CONFIG_VIDEO_HEXIUM_ORION=m
CONFIG_VIDEO_HEXIUM_GEMINI=m
CONFIG_VIDEO_CX88=m
CONFIG_VIDEO_CX88_BLACKBIRD=m
CONFIG_VIDEO_CX88_DVB=m
CONFIG_VIDEO_CX88_MPEG=m
CONFIG_VIDEO_CX88_VP3054=m
CONFIG_VIDEO_CX23885=m
CONFIG_VIDEO_AU0828=m
CONFIG_VIDEO_IVTV=m
CONFIG_VIDEO_FB_IVTV=m
CONFIG_VIDEO_SAA7164=m
CONFIG_VIDEO_CAFE_CCIC=m
CONFIG_SOC_CAMERA=m
CONFIG_SOC_CAMERA_MT9M001=m
CONFIG_SOC_CAMERA_MT9M111=m
CONFIG_SOC_CAMERA_MT9T031=m
CONFIG_SOC_CAMERA_MT9T112=m
CONFIG_SOC_CAMERA_MT9V022=m
CONFIG_SOC_CAMERA_RJ54N1=m
CONFIG_SOC_CAMERA_TW9910=m
CONFIG_SOC_CAMERA_PLATFORM=m
CONFIG_SOC_CAMERA_OV772X=m
CONFIG_SOC_CAMERA_OV9640=m
CONFIG_V4L_USB_DRIVERS=y
CONFIG_USB_VIDEO_CLASS=m
CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV=y
CONFIG_USB_GSPCA=m
CONFIG_USB_M5602=m
CONFIG_USB_STV06XX=m
CONFIG_USB_GL860=m
CONFIG_USB_GSPCA_BENQ=m
CONFIG_USB_GSPCA_CONEX=m
CONFIG_USB_GSPCA_CPIA1=m
CONFIG_USB_GSPCA_ETOMS=m
CONFIG_USB_GSPCA_FINEPIX=m
CONFIG_USB_GSPCA_JEILINJ=m
CONFIG_USB_GSPCA_MARS=m
CONFIG_USB_GSPCA_MR97310A=m
CONFIG_USB_GSPCA_OV519=m
CONFIG_USB_GSPCA_OV534=m
CONFIG_USB_GSPCA_OV534_9=m
CONFIG_USB_GSPCA_PAC207=m
CONFIG_USB_GSPCA_PAC7302=m
CONFIG_USB_GSPCA_PAC7311=m
CONFIG_USB_GSPCA_SN9C2028=m
CONFIG_USB_GSPCA_SN9C20X=m
CONFIG_USB_GSPCA_SONIXB=m
CONFIG_USB_GSPCA_SONIXJ=m
CONFIG_USB_GSPCA_SPCA500=m
CONFIG_USB_GSPCA_SPCA501=m
CONFIG_USB_GSPCA_SPCA505=m
CONFIG_USB_GSPCA_SPCA506=m
CONFIG_USB_GSPCA_SPCA508=m
CONFIG_USB_GSPCA_SPCA561=m
CONFIG_USB_GSPCA_SQ905=m
CONFIG_USB_GSPCA_SQ905C=m
CONFIG_USB_GSPCA_STK014=m
CONFIG_USB_GSPCA_STV0680=m
CONFIG_USB_GSPCA_SUNPLUS=m
CONFIG_USB_GSPCA_T613=m
CONFIG_USB_GSPCA_TV8532=m
CONFIG_USB_GSPCA_VC032X=m
CONFIG_USB_GSPCA_ZC3XX=m
CONFIG_VIDEO_PVRUSB2=m
CONFIG_VIDEO_HDPVR=m
CONFIG_VIDEO_EM28XX=m
CONFIG_VIDEO_EM28XX_ALSA=m
CONFIG_VIDEO_EM28XX_DVB=m
CONFIG_VIDEO_TLG2300=m
CONFIG_VIDEO_CX231XX=m
CONFIG_VIDEO_CX231XX_ALSA=m
CONFIG_VIDEO_CX231XX_DVB=m
CONFIG_VIDEO_USBVISION=m
CONFIG_VIDEO_USBVIDEO=m
CONFIG_USB_IBMCAM=m
CONFIG_USB_KONICAWC=m
CONFIG_USB_QUICKCAM_MESSENGER=m
CONFIG_USB_ET61X251=m
CONFIG_VIDEO_OVCAMCHIP=m
CONFIG_USB_W9968CF=m
CONFIG_USB_OV511=m
CONFIG_USB_SE401=m
CONFIG_USB_SN9C102=m
CONFIG_USB_STV680=m
CONFIG_USB_ZC0301=m
CONFIG_USB_PWC=m
# CONFIG_USB_PWC_DEBUG is not set
CONFIG_USB_PWC_INPUT_EVDEV=y
CONFIG_USB_ZR364XX=m
CONFIG_USB_S2255=m
CONFIG_V4L_MEM2MEM_DRIVERS=y
CONFIG_VIDEO_MEM2MEM_TESTDEV=m
# CONFIG_RADIO_ADAPTERS is not set
CONFIG_DVB_MAX_ADAPTERS=8
# CONFIG_DVB_DYNAMIC_MINORS is not set
# CONFIG_DVB_CAPTURE_DRIVERS is not set
CONFIG_DVB_BT8XX=m
CONFIG_DVB_STB6100=m
CONFIG_DVB_CX24123=m
CONFIG_DVB_MT312=m
CONFIG_DVB_ZL10036=m
CONFIG_DVB_ZL10039=m
CONFIG_DVB_STV0288=m
CONFIG_DVB_STB6000=m
CONFIG_DVB_STV0299=m
CONFIG_DVB_STV6110=m
CONFIG_DVB_STV0900=m
CONFIG_DVB_TDA10086=m
CONFIG_DVB_TDA826X=m
CONFIG_DVB_CX24116=m
CONFIG_DVB_DS3000=m
CONFIG_DVB_CX22702=m
CONFIG_DVB_TDA1004X=m
CONFIG_DVB_MT352=m
CONFIG_DVB_ZL10353=m
CONFIG_DVB_DIB7000P=m
CONFIG_DVB_TDA10048=m
CONFIG_DVB_TDA10023=m
CONFIG_DVB_NXT200X=m
CONFIG_DVB_OR51132=m
CONFIG_DVB_LGDT330X=m
CONFIG_DVB_LGDT3305=m
CONFIG_DVB_S5H1409=m
CONFIG_DVB_AU8522=m
CONFIG_DVB_S5H1411=m
CONFIG_DVB_PLL=m
CONFIG_DVB_LNBP21=m
CONFIG_DVB_ISL6405=m
CONFIG_DVB_ISL6421=m
CONFIG_DAB=y
CONFIG_USB_DABUSB=m
#
# Graphics support
#
CONFIG_AGP=m
# CONFIG_AGP_ALI is not set
CONFIG_AGP_ATI=m
CONFIG_AGP_AMD=m
# CONFIG_AGP_AMD64 is not set
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
CONFIG_VGA_ARB=y
CONFIG_VGA_ARB_MAX_GPUS=16
# CONFIG_VGA_SWITCHEROO is not set
CONFIG_DRM=m
CONFIG_DRM_KMS_HELPER=m
CONFIG_DRM_TTM=m
CONFIG_DRM_TDFX=m
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
# CONFIG_DRM_RADEON_KMS is not set
CONFIG_DRM_MGA=m
CONFIG_DRM_SIS=m
CONFIG_DRM_VIA=m
CONFIG_DRM_SAVAGE=m
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=m
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=m
CONFIG_FB_BOOT_VESA_SUPPORT=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_UVESA is not set
CONFIG_FB_VESA=y
# CONFIG_FB_N411 is not set
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_LE80578 is not set
# CONFIG_FB_MATROX is not set
CONFIG_FB_RADEON=m
CONFIG_FB_RADEON_I2C=y
# CONFIG_FB_RADEON_BACKLIGHT is not set
# CONFIG_FB_RADEON_DEBUG is not set
CONFIG_FB_ATY128=m
# CONFIG_FB_ATY128_BACKLIGHT is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_S3 is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_VIA is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_CARMINE is not set
# CONFIG_FB_TMIO is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_METRONOME is not set
# CONFIG_FB_MB862XX is not set
# CONFIG_FB_BROADSHEET is not set
CONFIG_BACKLIGHT_LCD_SUPPORT=y
# CONFIG_LCD_CLASS_DEVICE is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_GENERIC is not set
# CONFIG_BACKLIGHT_PROGEAR is not set
# CONFIG_BACKLIGHT_MBP_NVIDIA is not set
# CONFIG_BACKLIGHT_SAHARA is not set
# CONFIG_BACKLIGHT_ADP8860 is not set
#
# Display device support
#
CONFIG_DISPLAY_SUPPORT=m
#
# Display hardware drivers
#
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_7x14 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_SOUND=y
CONFIG_SOUND_OSS_CORE=y
CONFIG_SOUND_OSS_CORE_PRECLAIM=y
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_HRTIMER=m
CONFIG_SND_SEQ_HRTIMER_DEFAULT=y
CONFIG_SND_DYNAMIC_MINORS=y
# CONFIG_SND_SUPPORT_OLD_API is not set
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
CONFIG_SND_VMASTER=y
CONFIG_SND_DMA_SGBUF=y
CONFIG_SND_RAWMIDI_SEQ=m
# CONFIG_SND_OPL3_LIB_SEQ is not set
# CONFIG_SND_OPL4_LIB_SEQ is not set
# CONFIG_SND_SBAWE_SEQ is not set
CONFIG_SND_EMU10K1_SEQ=m
CONFIG_SND_AC97_CODEC=m
# CONFIG_SND_DRIVERS is not set
CONFIG_SND_PCI=y
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ASIHPI is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AW2 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
CONFIG_SND_CA0106=m
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_OXYGEN is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5530 is not set
# CONFIG_SND_CS5535AUDIO is not set
CONFIG_SND_CTXFI=m
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_INDIGOIOX is not set
# CONFIG_SND_INDIGODJX is not set
CONFIG_SND_EMU10K1=m
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_HIFIER is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_LX6464ES is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SIS7019 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VIRTUOSO is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_USB is not set
# CONFIG_SND_SOC is not set
# CONFIG_SOUND_PRIME is not set
CONFIG_AC97_BUS=m
# CONFIG_HID_SUPPORT is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
CONFIG_USB_MON=y
CONFIG_USB_WUSB_CBAF=m
# CONFIG_USB_WUSB_CBAF_DEBUG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_C67X00_HCD=m
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_OXU210HP_HCD=m
CONFIG_USB_ISP116X_HCD=m
CONFIG_USB_ISP1362_HCD=m
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_U132_HCD=m
CONFIG_USB_SL811_HCD=m
CONFIG_USB_R8A66597_HCD=m
#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
CONFIG_USB_WDM=m
CONFIG_USB_TMC=m
#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#
#
# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=m
CONFIG_USB_STORAGE_FREECOM=m
CONFIG_USB_STORAGE_ISD200=m
CONFIG_USB_STORAGE_USBAT=m
CONFIG_USB_STORAGE_SDDR09=m
CONFIG_USB_STORAGE_SDDR55=m
CONFIG_USB_STORAGE_JUMPSHOT=m
CONFIG_USB_STORAGE_ALAUDA=m
CONFIG_USB_STORAGE_ONETOUCH=m
CONFIG_USB_STORAGE_KARMA=m
CONFIG_USB_STORAGE_CYPRESS_ATACB=m
# CONFIG_USB_LIBUSUAL is not set
#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m
#
# USB port drivers
#
CONFIG_USB_USS720=m
CONFIG_USB_SERIAL=m
CONFIG_USB_EZUSB=y
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRCABLE=m
CONFIG_USB_SERIAL_ARK3116=m
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_CH341=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP210X=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_IUU=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_MOS7720=m
CONFIG_USB_SERIAL_MOS7715_PARPORT=y
CONFIG_USB_SERIAL_MOS7840=m
CONFIG_USB_SERIAL_MOTOROLA=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_SERIAL_OTI6858=m
CONFIG_USB_SERIAL_QCAUX=m
CONFIG_USB_SERIAL_QUALCOMM=m
CONFIG_USB_SERIAL_SPCP8X5=m
CONFIG_USB_SERIAL_HP4X=m
CONFIG_USB_SERIAL_SAFE=m
CONFIG_USB_SERIAL_SAFE_PADDED=y
CONFIG_USB_SERIAL_SIEMENS_MPI=m
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
CONFIG_USB_SERIAL_SYMBOL=m
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_WWAN=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_SERIAL_OPTICON=m
CONFIG_USB_SERIAL_VIVOPAY_SERIAL=m
CONFIG_USB_SERIAL_ZIO=m
CONFIG_USB_SERIAL_DEBUG=m
#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_ADUTUX=m
CONFIG_USB_SEVSEG=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
CONFIG_USB_LED=m
CONFIG_USB_CYPRESS_CY7C63=m
CONFIG_USB_CYTHERM=m
CONFIG_USB_IDMOUSE=m
CONFIG_USB_FTDI_ELAN=m
CONFIG_USB_APPLEDISPLAY=m
CONFIG_USB_SISUSBVGA=m
CONFIG_USB_SISUSBVGA_CON=y
CONFIG_USB_LD=m
CONFIG_USB_TRANCEVIBRATOR=m
CONFIG_USB_IOWARRIOR=m
CONFIG_USB_TEST=m
CONFIG_USB_ISIGHTFW=m
CONFIG_USB_ATM=m
CONFIG_USB_SPEEDTOUCH=m
CONFIG_USB_CXACRU=m
CONFIG_USB_UEAGLEATM=m
CONFIG_USB_XUSBATM=m
# CONFIG_USB_GADGET is not set
#
# OTG and related infrastructure
#
CONFIG_USB_OTG_UTILS=y
CONFIG_USB_GPIO_VBUS=m
CONFIG_NOP_USB_XCEIV=m
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=m
#
# LED drivers
#
CONFIG_LEDS_NET5501=m
CONFIG_LEDS_ALIX2=m
CONFIG_LEDS_GPIO=m
CONFIG_LEDS_GPIO_PLATFORM=y
CONFIG_LEDS_LP3944=m
CONFIG_LEDS_CLEVO_MAIL=m
CONFIG_LEDS_PCA955X=m
CONFIG_LEDS_BD2802=m
CONFIG_LEDS_INTEL_SS4200=m
CONFIG_LEDS_LT3593=m
CONFIG_LEDS_TRIGGERS=y
#
# LED Triggers
#
CONFIG_LEDS_TRIGGER_TIMER=m
CONFIG_LEDS_TRIGGER_HEARTBEAT=m
CONFIG_LEDS_TRIGGER_BACKLIGHT=m
CONFIG_LEDS_TRIGGER_GPIO=m
CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
#
# iptables trigger is under Netfilter config (LED target)
#
# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
CONFIG_EDAC=y
#
# Reporting subsystems
#
# CONFIG_EDAC_DEBUG is not set
CONFIG_EDAC_DECODE_MCE=y
# CONFIG_EDAC_MM_EDAC is not set
CONFIG_RTC_LIB=m
CONFIG_RTC_CLASS=m
#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
CONFIG_RTC_DRV_TEST=m
#
# I2C RTC drivers
#
# CONFIG_RTC_DRV_DS1307 is not set
# CONFIG_RTC_DRV_DS1374 is not set
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_MAX6900 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
# CONFIG_RTC_DRV_BQ32K is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
#
#
# Platform RTC drivers
#
CONFIG_RTC_DRV_CMOS=m
# CONFIG_RTC_DRV_DS1286 is not set
# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_MSM6242 is not set
# CONFIG_RTC_DRV_BQ4802 is not set
# CONFIG_RTC_DRV_RP5C01 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
# on-CPU RTC drivers
#
# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
# CONFIG_STAGING is not set
# CONFIG_X86_PLATFORM_DEVICES is not set
#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_FIRMWARE_MEMMAP=y
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
CONFIG_DMIID=y
CONFIG_ISCSI_IBFT_FIND=y
CONFIG_ISCSI_IBFT=m
#
# File systems
#
CONFIG_EXT2_FS=m
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=m
CONFIG_EXT3_DEFAULTS_TO_ORDERED=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_EXT4_FS=m
CONFIG_EXT4_FS_XATTR=y
CONFIG_EXT4_FS_POSIX_ACL=y
CONFIG_EXT4_FS_SECURITY=y
# CONFIG_EXT4_DEBUG is not set
CONFIG_JBD=m
CONFIG_JBD2=m
CONFIG_FS_MBCACHE=m
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_REISERFS_FS_XATTR is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_QUOTA=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
# CONFIG_QUOTA_DEBUG is not set
# CONFIG_QFMT_V1 is not set
# CONFIG_QFMT_V2 is not set
CONFIG_QUOTACTL=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
CONFIG_FUSE_FS=m
CONFIG_CUSE=m
CONFIG_GENERIC_ACL=y
#
# Caches
#
CONFIG_FSCACHE=m
# CONFIG_FSCACHE_STATS is not set
# CONFIG_FSCACHE_HISTOGRAM is not set
# CONFIG_FSCACHE_DEBUG is not set
# CONFIG_FSCACHE_OBJECT_LIST is not set
CONFIG_CACHEFILES=m
# CONFIG_CACHEFILES_DEBUG is not set
# CONFIG_CACHEFILES_HISTOGRAM is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_CONFIGFS_FS=y
CONFIG_MISC_FILESYSTEMS=y
CONFIG_HFSPLUS_FS=m
CONFIG_JFFS2_FS=m
CONFIG_JFFS2_FS_DEBUG=0
CONFIG_JFFS2_FS_WRITEBUFFER=y
# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
# CONFIG_JFFS2_LZO is not set
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_UBIFS_FS=m
CONFIG_UBIFS_FS_XATTR=y
CONFIG_UBIFS_FS_ADVANCED_COMPR=y
CONFIG_UBIFS_FS_LZO=y
CONFIG_UBIFS_FS_ZLIB=y
# CONFIG_UBIFS_FS_DEBUG is not set
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
CONFIG_SQUASHFS_XATTRS=y
CONFIG_SQUASHFS_EMBEDDED=y
CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
CONFIG_VXFS_FS=m
CONFIG_MINIX_FS=m
CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
CONFIG_QNX4FS_FS=m
CONFIG_ROMFS_FS=y
CONFIG_ROMFS_BACKED_BY_BLOCK=y
# CONFIG_ROMFS_BACKED_BY_MTD is not set
# CONFIG_ROMFS_BACKED_BY_BOTH is not set
CONFIG_ROMFS_ON_BLOCK=y
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
# CONFIG_UFS_DEBUG is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
CONFIG_CIFS_WEAK_PW_HASH=y
# CONFIG_CIFS_UPCALL is not set
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_DFS_UPCALL is not set
CONFIG_NCP_FS=m
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
CONFIG_NCPFS_STRONG=y
CONFIG_NCPFS_NFS_NS=y
CONFIG_NCPFS_OS2_NS=y
CONFIG_NCPFS_SMALLDOS=y
CONFIG_NCPFS_NLS=y
CONFIG_NCPFS_EXTRAS=y
CONFIG_CODA_FS=m
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=0
# CONFIG_MAGIC_SYSRQ is not set
CONFIG_STRIP_ASM_SYMS=y
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_DETECT_HUNG_TASK=y
# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_SLUB_DEBUG_ON is not set
# CONFIG_SLUB_STATS is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_VIRTUAL is not set
# CONFIG_DEBUG_WRITECOUNT is not set
CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_ARCH_WANT_FRAME_POINTERS=y
CONFIG_FRAME_POINTER=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_CPU_NOTIFIER_ERROR_INJECT is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_USER_STACKTRACE_SUPPORT=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_FP_TEST=y
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_ATOMIC64_SELFTEST is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_HAVE_ARCH_KMEMCHECK=y
CONFIG_STRICT_DEVMEM=y
CONFIG_X86_VERBOSE_BOOTUP=y
CONFIG_EARLY_PRINTK=y
# CONFIG_EARLY_PRINTK_DBGP is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PER_CPU_MAPS is not set
# CONFIG_X86_PTDUMP is not set
CONFIG_DEBUG_RODATA=y
# CONFIG_DEBUG_RODATA_TEST is not set
# CONFIG_DEBUG_NX_TEST is not set
# CONFIG_4KSTACKS is not set
CONFIG_DOUBLEFAULT=y
# CONFIG_IOMMU_STRESS is not set
CONFIG_HAVE_MMIOTRACE_SUPPORT=y
CONFIG_IO_DELAY_TYPE_0X80=0
CONFIG_IO_DELAY_TYPE_0XED=1
CONFIG_IO_DELAY_TYPE_UDELAY=2
CONFIG_IO_DELAY_TYPE_NONE=3
CONFIG_IO_DELAY_0X80=y
# CONFIG_IO_DELAY_0XED is not set
# CONFIG_IO_DELAY_UDELAY is not set
# CONFIG_IO_DELAY_NONE is not set
CONFIG_DEFAULT_IO_DELAY_TYPE=0
# CONFIG_CPA_DEBUG is not set
CONFIG_OPTIMIZE_INLINING=y
# CONFIG_DEBUG_STRICT_USER_COPY_CHECKS is not set
#
# Security options
#
CONFIG_KEYS=y
CONFIG_KEYS_DEBUG_PROC_KEYS=y
CONFIG_SECURITY=y
CONFIG_SECURITYFS=y
CONFIG_SECURITY_NETWORK=y
CONFIG_SECURITY_NETWORK_XFRM=y
# CONFIG_SECURITY_PATH is not set
# CONFIG_SECURITY_SELINUX is not set
# CONFIG_SECURITY_TOMOYO is not set
# CONFIG_IMA is not set
# CONFIG_DEFAULT_SECURITY_SELINUX is not set
# CONFIG_DEFAULT_SECURITY_SMACK is not set
# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
CONFIG_CRYPTO_FIPS=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG=m
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_PCOMP=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
CONFIG_CRYPTO_MANAGER_TESTS=y
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_NULL=y
CONFIG_CRYPTO_WORKQUEUE=y
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_AUTHENC=y
CONFIG_CRYPTO_TEST=m
#
# Authenticated Encryption with Associated Data
#
CONFIG_CRYPTO_CCM=m
CONFIG_CRYPTO_GCM=m
CONFIG_CRYPTO_SEQIV=m
#
# Block modes
#
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_CTR=m
CONFIG_CRYPTO_CTS=m
CONFIG_CRYPTO_ECB=y
CONFIG_CRYPTO_PCBC=y
#
# Hash modes
#
CONFIG_CRYPTO_HMAC=y
#
# Digest
#
CONFIG_CRYPTO_CRC32C=y
CONFIG_CRYPTO_CRC32C_INTEL=m
CONFIG_CRYPTO_GHASH=m
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=y
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_SHA512=y
CONFIG_CRYPTO_TGR192=y
CONFIG_CRYPTO_WP512=y
#
# Ciphers
#
CONFIG_CRYPTO_AES=y
CONFIG_CRYPTO_AES_586=y
CONFIG_CRYPTO_ANUBIS=y
CONFIG_CRYPTO_ARC4=y
CONFIG_CRYPTO_BLOWFISH=y
CONFIG_CRYPTO_CAMELLIA=y
CONFIG_CRYPTO_CAST5=y
CONFIG_CRYPTO_CAST6=y
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_FCRYPT=y
CONFIG_CRYPTO_KHAZAD=y
CONFIG_CRYPTO_SEED=y
CONFIG_CRYPTO_SERPENT=y
CONFIG_CRYPTO_TEA=y
CONFIG_CRYPTO_TWOFISH=y
CONFIG_CRYPTO_TWOFISH_COMMON=y
CONFIG_CRYPTO_TWOFISH_586=y
#
# Compression
#
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
#
# Random Number Generation
#
CONFIG_CRYPTO_ANSI_CPRNG=m
CONFIG_CRYPTO_HW=y
CONFIG_CRYPTO_DEV_PADLOCK=m
CONFIG_CRYPTO_DEV_PADLOCK_AES=m
CONFIG_CRYPTO_DEV_PADLOCK_SHA=m
CONFIG_CRYPTO_DEV_GEODE=m
CONFIG_CRYPTO_DEV_HIFN_795X=m
CONFIG_CRYPTO_DEV_HIFN_795X_RNG=y
CONFIG_HAVE_KVM=y
# CONFIG_VIRTUALIZATION is not set
# CONFIG_BINARY_PRINTF is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_GENERIC_FIND_FIRST_BIT=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=m
CONFIG_CRC16=y
CONFIG_CRC_T10DIF=m
CONFIG_CRC_ITU_T=y
CONFIG_CRC32=y
CONFIG_CRC7=m
CONFIG_LIBCRC32C=y
CONFIG_AUDIT_GENERIC=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_LZO_COMPRESS=m
CONFIG_LZO_DECOMPRESS=y
CONFIG_DECOMPRESS_GZIP=y
CONFIG_DECOMPRESS_BZIP2=y
CONFIG_DECOMPRESS_LZMA=y
CONFIG_DECOMPRESS_LZO=y
CONFIG_REED_SOLOMON=m
CONFIG_REED_SOLOMON_DEC16=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_NLATTR=y
[-- Attachment #3: main partition --]
[-- Type: TEXT/PLAIN, Size: 724 bytes --]
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux bigred 2.6.31.14-smp #1 SMP Fri Nov 19 17:58:27 PST 2010 i686 AMD Athlon(tm) MP 2000+ AuthenticAMD GNU/Linux
Gnu C 4.5.2 20101125 (prerelease)
Gnu make 3.81
binutils 2.20.51.0.8.20100412
util-linux 2.17.2
mount support
module-init-tools found
Linux C Library 2.11.1
Dynamic linker (ldd) 2.11.1
Linux C++ Library 6.0.14
Procps 3.2.8
Kbd 1.15.2
oprofile 0.9.6
Sh-utils 8.5
Modules Loaded floppy
[-- Attachment #4: test partition --]
[-- Type: TEXT/PLAIN, Size: 1244 bytes --]
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux bigred 2.6.35.9-smp #1 SMP Tue Dec 7 20:27:42 PST 2010 i686 AMD Athlon(tm) MP 2000+ AuthenticAMD GNU/Linux
Gnu C 4.5.2 20101125 (prerelease)
Gnu make 3.82
binutils 2.20.51.0.11.20100810
util-linux 2.18
mount support
module-init-tools 3.12
e2fsprogs 1.41.12
reiserfsprogs 3.6.21
Linux C Library 2.12.1
Dynamic linker (ldd) 2.12.1
Procps 3.2.8
Net-tools 1.60
Kbd 1.15.2
Sh-utils 8.6
wireless-tools 29
Modules Loaded snd_seq_dummy snd_seq_oss snd_seq_midi_event snd_seq snd_pcm_oss snd_mixer_oss lp processor thermal thermal_sys ohci_hcd i2c_amd756 jedec_probe i2c_core ppdev snd_ca0106 snd_rawmidi ehci_hcd cfi_probe parport_pc gen_probe floppy snd_seq_device snd_ac97_codec parport cfi_util psmouse ohci1394 serio_raw amd76xrom amd_k7_agp ieee1394 agpgart ac97_bus snd_pcm snd_timer evdev hwmon mtd rtc_cmos chipreg rtc_core snd map_funcs rtc_lib snd_page_alloc amd_rng container button
[-- Attachment #5: dmesg-nobug --]
[-- Type: TEXT/PLAIN, Size: 20688 bytes --]
Linux version 2.6.35.9-smp (russ@bigred) (gcc version 4.5.2 20101125 (prerelease) (GCC) ) #1 SMP Tue Dec 7 20:27:42 PST 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000009fef0000 (usable)
BIOS-e820: 000000009fef0000 - 000000009feff000 (ACPI data)
BIOS-e820: 000000009feff000 - 000000009ff00000 (ACPI NVS)
BIOS-e820: 000000009ff00000 - 000000009ff80000 (usable)
BIOS-e820: 000000009ff80000 - 00000000a0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
DMI 2.3 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x9ff80 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CDFFF write-protect
CE000-DFFFF uncachable
E0000-E3FFF write-back
E4000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 080000000 mask FE0000000 write-back
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 15000-1a000
ACPI: RSDP 000f7100 00014 (v00 PTLTD )
ACPI: RSDT 9fefcf28 0002C (v01 PTLTD RSDT 06040000 LTP 00000000)
ACPI: FACP 9fefef2e 00074 (v01 AMD TECATE 06040000 PTL 000F4240)
ACPI: DSDT 9fefcf54 01FDA (v01 AMD AMDACPI 06040000 MSFT 0100000D)
ACPI: FACS 9fefffc0 00040
ACPI: APIC 9fefefa2 0005E (v01 PTLTD ? APIC 06040000 LTP 00000000)
ACPI: Local APIC address 0xfee00000
1671MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00016000 - 0001cf00
(8/32 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#1 [0001000000 - 000152e5a4] TEXT DATA BSS ==> [0001000000 - 000152e5a4]
#2 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#3 [000152f000 - 00015350f4] BRK ==> [000152f000 - 00015350f4]
#4 [0000010000 - 0000011000] TRAMPOLINE ==> [0000010000 - 0000011000]
#5 [0000011000 - 0000015000] ACPI WAKEUP ==> [0000011000 - 0000015000]
#6 [0000015000 - 0000016000] PGTABLE ==> [0000015000 - 0000016000]
#7 [0000016000 - 000001d000] BOOTMAP ==> [0000016000 - 000001d000]
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0009ff80
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0009fef0
0: 0x0009ff00 -> 0x0009ff80
On node 0 totalpages: 655103
free_area_init_node: node 0, pgdat c148c400, node_mem_map c1537200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 3344 pages used for memmap
HighMem zone: 424546 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
Allocating PCI resources starting at a0000000 (gap: a0000000:5ec00000)
setup_percpu: NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 13 pages/cpu @c2c00000 s29632 r0 d23616 u2097152
pcpu-alloc: s29632 r0 d23616 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 649983
Kernel command line: root=/dev/sda2
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0009ff80)
Memory: 2593628k/2620928k available (3394k kernel code, 26784k reserved, 1279k data, 348k init, 1711560k highmem)
virtual kernel memory layout:
fixmap : 0xfff8f000 - 0xfffff000 ( 448 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1491000 - 0xc14e8000 ( 348 kB)
.data : 0xc1350b7a - 0xc149089c (1279 kB)
.text : 0xc1000000 - 0xc1350b7a (3394 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:320
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 1666.939 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3333.87 BogoMIPS (lpj=1666939)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
mce: CPU supports 4 MCE banks
Performance Events: AMD PMU driver.
... version: 0
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 00007fffffffffff
... fixed-purpose events: 0
... event mask: 000000000000000f
ACPI: Core revision 20100428
Enabling APIC mode: Flat. Using 1 I/O APICs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: AMD Athlon(tm) MP 2000+ stepping 02
Booting Node 0, Processors #1 Ok.
Initializing CPU#1
Brought up 2 CPUs
Total of 2 processors activated (6666.79 BogoMIPS).
devtmpfs: initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=3
PCI: Using configuration type 1 for base access
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x0d00-0x7fff] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x8100-0xffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000ccfff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xa0000000-0xfebfffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000d8000-0x000dbfff] (ignored)
pci 0000:00:00.0: reg 10: [mem 0xec000000-0xefffffff pref]
pci 0000:00:00.0: reg 14: [mem 0xe8500000-0xe8500fff pref]
pci 0000:00:00.0: reg 18: [io 0x1010-0x1013]
pci 0000:00:07.1: reg 20: [io 0xf000-0xf00f]
pci 0000:01:05.0: reg 10: [mem 0xf0000000-0xf7ffffff pref]
pci 0000:01:05.0: reg 14: [io 0x2000-0x20ff]
pci 0000:01:05.0: reg 18: [mem 0xe8020000-0xe803ffff]
pci 0000:01:05.0: reg 20: [mem 0xe8000000-0xe800ffff]
pci 0000:01:05.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:01:05.0: supports D1 D2
pci 0000:01:05.1: supports D1
pci 0000:00:01.0: PCI bridge to [bus 01-02]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe81fffff]
pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
pci 0000:02:00.0: reg 10: [mem 0xe8100000-0xe8100fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:02:00.0: PME# disabled
pci 0000:01:05.1: PCI bridge to [bus 02-02]
pci 0000:01:05.1: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:01:05.1: bridge window [mem 0xe8100000-0xe81fffff]
pci 0000:01:05.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:03:00.0: reg 10: [mem 0xe8200000-0xe8200fff]
pci 0000:03:04.0: reg 10: [io 0x3480-0x349f]
pci 0000:03:04.0: supports D1 D2
pci 0000:03:06.0: reg 10: [io 0x3000-0x30ff]
pci 0000:03:06.0: reg 14: [mem 0xe8201000-0xe82011ff]
pci 0000:03:06.0: supports D1 D2
pci 0000:03:06.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:03:06.0: PME# disabled
pci 0000:03:08.0: reg 10: [io 0x3400-0x347f]
pci 0000:03:08.0: reg 14: [mem 0xe8201400-0xe820147f]
pci 0000:03:08.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:03:08.0: supports D1 D2
pci 0000:03:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:03:08.0: PME# disabled
pci 0000:00:10.0: PCI bridge to [bus 03-03]
pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
pci 0000:00:10.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
HEST: Table is not found!
vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 32 bytes
reserve RAM buffer: 000000000009f800 - 000000000009ffff
reserve RAM buffer: 000000009fef0000 - 000000009fffffff
reserve RAM buffer: 000000009ff80000 - 000000009fffffff
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: [mem 0xfffc0000-0xffffffff] has been reserved
system 00:00: [mem 0xffc00000-0xfff7ffff] has been reserved
system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:00: [mem 0x00100000-0x9fffffff] could not be reserved
system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:06: [io 0x04d0-0x04d1] has been reserved
Switching to clocksource acpi_pm
pci 0000:00:10.0: BAR 9: assigned [mem 0xa0000000-0xa00fffff pref]
pci 0000:01:05.0: BAR 6: assigned [mem 0xe8040000-0xe805ffff pref]
pci 0000:01:05.1: PCI bridge to [bus 02-02]
pci 0000:01:05.1: bridge window [io disabled]
pci 0000:01:05.1: bridge window [mem 0xe8100000-0xe81fffff]
pci 0000:01:05.1: bridge window [mem pref disabled]
pci 0000:00:01.0: PCI bridge to [bus 01-02]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe81fffff]
pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
pci 0000:03:08.0: BAR 6: assigned [mem 0xa0000000-0xa001ffff pref]
pci 0000:00:10.0: PCI bridge to [bus 03-03]
pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
pci 0000:00:10.0: bridge window [mem 0xa0000000-0xa00fffff pref]
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:01: resource 1 [mem 0xe8000000-0xe81fffff]
pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf7ffffff pref]
pci_bus 0000:02: resource 1 [mem 0xe8100000-0xe81fffff]
pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
pci_bus 0000:03: resource 1 [mem 0xe8200000-0xe82fffff]
pci_bus 0000:03: resource 2 [mem 0xa0000000-0xa00fffff pref]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:00:00.0: BIOS failed to enable PCI standards compliance; fixing this error
pci 0000:01:05.0: Boot video device
PCI: CLS 64 bytes, default 32
audit: initializing netlink socket (disabled)
type=2000 audit(1291754844.190:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1722
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for fcrypt (fcrypt-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
ERST: Table is not found!
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Loading iSCSI transport class v2.0-870.
pata_amd 0000:00:07.1: version 0.4.1
pata_amd 0000:00:07.1: setting latency timer to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
3c59x 0000:03:08.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
3c59x: Donald Becker and others.
0000:03:08.0: 3Com PCI 3c905C Tornado at f8066400.
usbmon: debugfs is not available
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
ata1.00: ATA-6: ST340810A, 3.39, max UDMA/100
ata1.00: 78165360 sectors, multi 16: LBA
ata1.01: ATA-6: ST3160023A, 8.01, max UDMA/100
ata1.01: 312581808 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST340810A 3.39 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
scsi 0:0:1:0: Direct-Access ATA ST3160023A 8.01 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
sd 0:0:1:0: Attached scsi generic sg1 type 0
sda1 sda2 sda3 sda4
sd 0:0:1:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:1:0: [sdb] Attached SCSI disk
ata2.00: ATAPI: LITE-ON DVDRW LH-20A1H, LL0C, max UDMA/66
ata2.01: ATAPI: MATSHITA CD-RW CW-7586, 1.08, max MWDMA2
ata2.00: limited to UDMA/33 due to 40-wire cable
ata2.00: configured for UDMA/33
ata2.01: configured for MWDMA2
scsi 1:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1H LL0C PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg2 type 5
scsi 1:0:1:0: CD-ROM MATSHITA CD-RW CW-7586 1.08 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
sr 1:0:1:0: Attached scsi generic sg3 type 5
REISERFS (device sda2): found reiserfs format "3.6" with standard journal
REISERFS (device sda2): using ordered data mode
REISERFS (device sda2): journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
REISERFS (device sda2): checking transaction log (sda2)
REISERFS (device sda2): Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly on device 8:2.
devtmpfs: mounted
Freeing unused kernel memory: 348k freed
Write protecting the kernel text: 3396k
Write protecting the kernel read-only data: 1032k
udev[679]: starting version 164
AMD768 RNG detected
Linux agpgart interface v0.103
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input3
ACPI: Sleep Button [SLPF]
ohci1394 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[18] MMIO=[e8100000-e81007ff] Max Packet=[2048] IR/IT contexts=[8/8]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
agpgart-amdk7 0000:00:00.0: AMD 760MP chipset
agpgart-amdk7 0000:00:00.0: AGP aperture is 64M @ 0xec000000
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:03:00.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:03:00.0: OHCI Host Controller
ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:03:00.0: irq 19, io mem 0xe8200000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.35.9-smp ohci_hcd
usb usb1: SerialNumber: 0000:03:00.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram
"amd76xrom" amd76xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug?
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Found: PMC Pm49FL004
"amd76xrom" @fff80000: Found 1 x8 devices at 0x0 in 8-bit bank
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0006bb0016042789]
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
number of JEDEC chips: 1
ACPI: acpi_idle registered with cpuidle
ppdev: user-space parallel port driver
CA0106 0000:03:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
snd-ca0106: Model 1006 Rev 00000000 Serial 10061102
lp0: using parport0 (interrupt-driven).
lp0: console ready
eth0: setting full-duplex.
[-- Attachment #6: dmesg2-withbug --]
[-- Type: TEXT/PLAIN, Size: 22734 bytes --]
Linux version 2.6.35.9-smp (russ@bigred) (gcc version 4.5.2 20101125 (prerelease) (GCC) ) #1 SMP Tue Dec 7 20:27:42 PST 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000009fef0000 (usable)
BIOS-e820: 000000009fef0000 - 000000009feff000 (ACPI data)
BIOS-e820: 000000009feff000 - 000000009ff00000 (ACPI NVS)
BIOS-e820: 000000009ff00000 - 000000009ff80000 (usable)
BIOS-e820: 000000009ff80000 - 00000000a0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
DMI 2.3 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x9ff80 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CDFFF write-protect
CE000-DFFFF uncachable
E0000-E3FFF write-back
E4000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 080000000 mask FE0000000 write-back
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 15000-1a000
ACPI: RSDP 000f7100 00014 (v00 PTLTD )
ACPI: RSDT 9fefcf28 0002C (v01 PTLTD RSDT 06040000 LTP 00000000)
ACPI: FACP 9fefef2e 00074 (v01 AMD TECATE 06040000 PTL 000F4240)
ACPI: DSDT 9fefcf54 01FDA (v01 AMD AMDACPI 06040000 MSFT 0100000D)
ACPI: FACS 9fefffc0 00040
ACPI: APIC 9fefefa2 0005E (v01 PTLTD ? APIC 06040000 LTP 00000000)
ACPI: Local APIC address 0xfee00000
1671MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00016000 - 0001cf00
(8/32 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#1 [0001000000 - 000152e5a4] TEXT DATA BSS ==> [0001000000 - 000152e5a4]
#2 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#3 [000152f000 - 00015350f4] BRK ==> [000152f000 - 00015350f4]
#4 [0000010000 - 0000011000] TRAMPOLINE ==> [0000010000 - 0000011000]
#5 [0000011000 - 0000015000] ACPI WAKEUP ==> [0000011000 - 0000015000]
#6 [0000015000 - 0000016000] PGTABLE ==> [0000015000 - 0000016000]
#7 [0000016000 - 000001d000] BOOTMAP ==> [0000016000 - 000001d000]
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0009ff80
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0009fef0
0: 0x0009ff00 -> 0x0009ff80
On node 0 totalpages: 655103
free_area_init_node: node 0, pgdat c148c400, node_mem_map c1537200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 3344 pages used for memmap
HighMem zone: 424546 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
Allocating PCI resources starting at a0000000 (gap: a0000000:5ec00000)
setup_percpu: NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 13 pages/cpu @c2c00000 s29632 r0 d23616 u2097152
pcpu-alloc: s29632 r0 d23616 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 649983
Kernel command line: root=/dev/sda2
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0009ff80)
Memory: 2593628k/2620928k available (3394k kernel code, 26784k reserved, 1279k data, 348k init, 1711560k highmem)
virtual kernel memory layout:
fixmap : 0xfff8f000 - 0xfffff000 ( 448 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1491000 - 0xc14e8000 ( 348 kB)
.data : 0xc1350b7a - 0xc149089c (1279 kB)
.text : 0xc1000000 - 0xc1350b7a (3394 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:320
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 1666.701 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3333.40 BogoMIPS (lpj=1666701)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
mce: CPU supports 4 MCE banks
Performance Events: AMD PMU driver.
... version: 0
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 00007fffffffffff
... fixed-purpose events: 0
... event mask: 000000000000000f
ACPI: Core revision 20100428
Enabling APIC mode: Flat. Using 1 I/O APICs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: AMD Athlon(tm) MP 2000+ stepping 02
Booting Node 0, Processors #1 Ok.
Initializing CPU#1
Brought up 2 CPUs
Total of 2 processors activated (6666.12 BogoMIPS).
devtmpfs: initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=3
PCI: Using configuration type 1 for base access
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x0d00-0x7fff] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x8100-0xffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000ccfff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xa0000000-0xfebfffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000d8000-0x000dbfff] (ignored)
pci 0000:00:00.0: reg 10: [mem 0xec000000-0xefffffff pref]
pci 0000:00:00.0: reg 14: [mem 0xe8500000-0xe8500fff pref]
pci 0000:00:00.0: reg 18: [io 0x1010-0x1013]
pci 0000:00:07.1: reg 20: [io 0xf000-0xf00f]
pci 0000:01:05.0: reg 10: [mem 0xf0000000-0xf7ffffff pref]
pci 0000:01:05.0: reg 14: [io 0x2000-0x20ff]
pci 0000:01:05.0: reg 18: [mem 0xe8020000-0xe803ffff]
pci 0000:01:05.0: reg 20: [mem 0xe8000000-0xe800ffff]
pci 0000:01:05.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:01:05.0: supports D1 D2
pci 0000:01:05.1: supports D1
pci 0000:00:01.0: PCI bridge to [bus 01-02]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe81fffff]
pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
pci 0000:02:00.0: reg 10: [mem 0xe8100000-0xe8100fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:02:00.0: PME# disabled
pci 0000:01:05.1: PCI bridge to [bus 02-02]
pci 0000:01:05.1: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:01:05.1: bridge window [mem 0xe8100000-0xe81fffff]
pci 0000:01:05.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:03:00.0: reg 10: [mem 0xe8200000-0xe8200fff]
pci 0000:03:04.0: reg 10: [io 0x3480-0x349f]
pci 0000:03:04.0: supports D1 D2
pci 0000:03:06.0: reg 10: [io 0x3000-0x30ff]
pci 0000:03:06.0: reg 14: [mem 0xe8201000-0xe82011ff]
pci 0000:03:06.0: supports D1 D2
pci 0000:03:06.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:03:06.0: PME# disabled
pci 0000:03:08.0: reg 10: [io 0x3400-0x347f]
pci 0000:03:08.0: reg 14: [mem 0xe8201400-0xe820147f]
pci 0000:03:08.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:03:08.0: supports D1 D2
pci 0000:03:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:03:08.0: PME# disabled
pci 0000:00:10.0: PCI bridge to [bus 03-03]
pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
pci 0000:00:10.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
HEST: Table is not found!
vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 32 bytes
reserve RAM buffer: 000000000009f800 - 000000000009ffff
reserve RAM buffer: 000000009fef0000 - 000000009fffffff
reserve RAM buffer: 000000009ff80000 - 000000009fffffff
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: [mem 0xfffc0000-0xffffffff] has been reserved
system 00:00: [mem 0xffc00000-0xfff7ffff] has been reserved
system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:00: [mem 0x00100000-0x9fffffff] could not be reserved
system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:06: [io 0x04d0-0x04d1] has been reserved
Switching to clocksource acpi_pm
pci 0000:00:10.0: BAR 9: assigned [mem 0xa0000000-0xa00fffff pref]
pci 0000:01:05.0: BAR 6: assigned [mem 0xe8040000-0xe805ffff pref]
pci 0000:01:05.1: PCI bridge to [bus 02-02]
pci 0000:01:05.1: bridge window [io disabled]
pci 0000:01:05.1: bridge window [mem 0xe8100000-0xe81fffff]
pci 0000:01:05.1: bridge window [mem pref disabled]
pci 0000:00:01.0: PCI bridge to [bus 01-02]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe81fffff]
pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
pci 0000:03:08.0: BAR 6: assigned [mem 0xa0000000-0xa001ffff pref]
pci 0000:00:10.0: PCI bridge to [bus 03-03]
pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
pci 0000:00:10.0: bridge window [mem 0xa0000000-0xa00fffff pref]
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:01: resource 1 [mem 0xe8000000-0xe81fffff]
pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf7ffffff pref]
pci_bus 0000:02: resource 1 [mem 0xe8100000-0xe81fffff]
pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
pci_bus 0000:03: resource 1 [mem 0xe8200000-0xe82fffff]
pci_bus 0000:03: resource 2 [mem 0xa0000000-0xa00fffff pref]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:00:00.0: BIOS failed to enable PCI standards compliance; fixing this error
pci 0000:01:05.0: Boot video device
PCI: CLS 64 bytes, default 32
audit: initializing netlink socket (disabled)
type=2000 audit(1291754958.188:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1722
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for fcrypt (fcrypt-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
ERST: Table is not found!
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Loading iSCSI transport class v2.0-870.
pata_amd 0000:00:07.1: version 0.4.1
pata_amd 0000:00:07.1: setting latency timer to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
3c59x 0000:03:08.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
3c59x: Donald Becker and others.
0000:03:08.0: 3Com PCI 3c905C Tornado at f8066400.
usbmon: debugfs is not available
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
ata1.00: ATA-6: ST340810A, 3.39, max UDMA/100
ata1.00: 78165360 sectors, multi 16: LBA
ata1.01: ATA-6: ST3160023A, 8.01, max UDMA/100
ata1.01: 312581808 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST340810A 3.39 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
sd 0:0:0:0: [sda] Write Protect is off
scsi 0:0:1:0: Direct-Access ATA ST3160023A 8.01 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
sd 0:0:1:0: Attached scsi generic sg1 type 0
sda1 sda2 sda3 sda4
sd 0:0:1:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:1:0: [sdb] Attached SCSI disk
ata2.00: ATAPI: LITE-ON DVDRW LH-20A1H, LL0C, max UDMA/66
ata2.01: ATAPI: MATSHITA CD-RW CW-7586, 1.08, max MWDMA2
ata2.00: limited to UDMA/33 due to 40-wire cable
ata2.00: configured for UDMA/33
ata2.01: configured for MWDMA2
scsi 1:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1H LL0C PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg2 type 5
scsi 1:0:1:0: CD-ROM MATSHITA CD-RW CW-7586 1.08 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
sr 1:0:1:0: Attached scsi generic sg3 type 5
REISERFS (device sda2): found reiserfs format "3.6" with standard journal
REISERFS (device sda2): using ordered data mode
REISERFS (device sda2): journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
REISERFS (device sda2): checking transaction log (sda2)
REISERFS (device sda2): Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly on device 8:2.
devtmpfs: mounted
Freeing unused kernel memory: 348k freed
Write protecting the kernel text: 3396k
Write protecting the kernel read-only data: 1032k
udev[679]: starting version 164
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input3
ACPI: Sleep Button [SLPF]
Linux agpgart interface v0.103
agpgart-amdk7 0000:00:00.0: AMD 760MP chipset
AMD768 RNG detected
agpgart-amdk7 0000:00:00.0: AGP aperture is 64M @ 0xec000000
"amd76xrom" amd76xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug?
CA0106 0000:03:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
snd-ca0106: Model 1006 Rev 00000000 Serial 10061102
BUG: unable to handle kernel paging request at f862aaa0
IP: [<f8120282>] simple_map_write+0x82/0xbb [map_funcs]
*pde = 36ad2067 *pte = 00000000
Oops: 0002 [#1] SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:07.1/host0/target0:0:1/0:0:1:0/block/sdb/removable
Modules linked in: rtc_core thermal_sys jedec_probe serio_raw rtc_lib snd_ca0106 snd_rawmidi snd_seq_device snd_ac97_codec cfi_probe hwmon gen_probe cfi_util amd76xrom(+) ac97_bus snd_pcm snd_timer container mtd amd_rng snd amd_k7_agp chipreg map_funcs snd_page_alloc agpgart button
Pid: 690, comm: modprobe Not tainted 2.6.35.9-smp #1 S2466 TIGER MPX/Unknown
EIP: 0060:[<f8120282>] EFLAGS: 00010212 CPU: 1
EIP is at simple_map_write+0x82/0xbb [map_funcs]
EAX: 000000aa EBX: 00000020 ECX: 00000008 EDX: 000000aa
ESI: f6869a48 EDI: f862aaa0 EBP: f6869a74 ESP: f6869a48
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process modprobe (pid: 690, ti=f6868000 task=f738ecb0 task.ti=f6868000)
Stack:
000000aa 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa
<0> 00000008 f6869b84 f6869a9c f6869d90 f8159ad4 000000aa 000000aa 000000aa
<0> 000000aa 000000aa 000000aa 000000aa 000000aa 000aaaa0 00000000 00000004
Call Trace:
[<f8159ad4>] ? cfi_qry_mode_on+0xc74/0x1130 [cfi_util]
[<f864be7c>] ? jedec_probe_chip+0x6fc/0x1394 [jedec_probe]
[<f819c1c1>] ? cfi_probe_chip+0x41/0x48c [cfi_probe]
[<f815d1aa>] ? mtd_do_chip_probe+0xaa/0x358 [gen_probe]
[<f819c00d>] ? cfi_probe+0xd/0x10 [cfi_probe]
[<f8129154>] ? do_map_probe+0x24/0x73 [chipreg]
[<f812621a>] ? init_amd76xrom+0x21a/0x3d2 [amd76xrom]
[<c100122d>] ? do_one_initcall+0x2d/0x180
[<f8126000>] ? init_amd76xrom+0x0/0x3d2 [amd76xrom]
[<c10614eb>] ? sys_init_module+0x9b/0x1e0
[<c10aa49d>] ? sys_write+0x3d/0x70
[<c134f83c>] ? syscall_call+0x7/0xb
Code: 7f 17 f0 83 04 24 00 8b 5d f4 8b 75 f8 8b 7d fc 89 ec 5d c3 90 8d 74 26 00 01 cf 81 fb ff 01 00 00 77 2e 89 d9 c1 e9 02 8d 75 d4 <f3> a5 89 d9 83 e1 03 74 02 f3 a4 eb ca 90 01 cf 88 07 eb c3 66
EIP: [<f8120282>] simple_map_write+0x82/0xbb [map_funcs] SS:ESP 0068:f6869a48
CR2: 00000000f862aaa0
---[ end trace 03e904d3580c8593 ]---
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram
ohci1394 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[18] MMIO=[e8100000-e81007ff] Max Packet=[2048] IR/IT contexts=[8/8]
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ACPI: acpi_idle registered with cpuidle
ppdev: user-space parallel port driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:03:00.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:03:00.0: OHCI Host Controller
ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:03:00.0: irq 19, io mem 0xe8200000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.35.9-smp ohci_hcd
usb usb1: SerialNumber: 0000:03:00.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0006bb0016042789]
lp0: using parport0 (interrupt-driven).
lp0: console ready
eth0: setting full-duplex.
[-- Attachment #7: dmesg3-withbug --]
[-- Type: TEXT/PLAIN, Size: 22853 bytes --]
Linux version 2.6.35.9-smp (russ@bigred) (gcc version 4.5.2 20101125 (prerelease) (GCC) ) #1 SMP Tue Dec 7 20:27:42 PST 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000009fef0000 (usable)
BIOS-e820: 000000009fef0000 - 000000009feff000 (ACPI data)
BIOS-e820: 000000009feff000 - 000000009ff00000 (ACPI NVS)
BIOS-e820: 000000009ff00000 - 000000009ff80000 (usable)
BIOS-e820: 000000009ff80000 - 00000000a0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
DMI 2.3 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x9ff80 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CDFFF write-protect
CE000-DFFFF uncachable
E0000-E3FFF write-back
E4000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 080000000 mask FE0000000 write-back
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 15000-1a000
ACPI: RSDP 000f7100 00014 (v00 PTLTD )
ACPI: RSDT 9fefcf28 0002C (v01 PTLTD RSDT 06040000 LTP 00000000)
ACPI: FACP 9fefef2e 00074 (v01 AMD TECATE 06040000 PTL 000F4240)
ACPI: DSDT 9fefcf54 01FDA (v01 AMD AMDACPI 06040000 MSFT 0100000D)
ACPI: FACS 9fefffc0 00040
ACPI: APIC 9fefefa2 0005E (v01 PTLTD ? APIC 06040000 LTP 00000000)
ACPI: Local APIC address 0xfee00000
1671MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00016000 - 0001cf00
(8/32 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#1 [0001000000 - 000152e5a4] TEXT DATA BSS ==> [0001000000 - 000152e5a4]
#2 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#3 [000152f000 - 00015350f4] BRK ==> [000152f000 - 00015350f4]
#4 [0000010000 - 0000011000] TRAMPOLINE ==> [0000010000 - 0000011000]
#5 [0000011000 - 0000015000] ACPI WAKEUP ==> [0000011000 - 0000015000]
#6 [0000015000 - 0000016000] PGTABLE ==> [0000015000 - 0000016000]
#7 [0000016000 - 000001d000] BOOTMAP ==> [0000016000 - 000001d000]
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0009ff80
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0009fef0
0: 0x0009ff00 -> 0x0009ff80
On node 0 totalpages: 655103
free_area_init_node: node 0, pgdat c148c400, node_mem_map c1537200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 3344 pages used for memmap
HighMem zone: 424546 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
Allocating PCI resources starting at a0000000 (gap: a0000000:5ec00000)
setup_percpu: NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 13 pages/cpu @c2c00000 s29632 r0 d23616 u2097152
pcpu-alloc: s29632 r0 d23616 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 649983
Kernel command line: root=/dev/sda2
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0009ff80)
Memory: 2593628k/2620928k available (3394k kernel code, 26784k reserved, 1279k data, 348k init, 1711560k highmem)
virtual kernel memory layout:
fixmap : 0xfff8f000 - 0xfffff000 ( 448 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1491000 - 0xc14e8000 ( 348 kB)
.data : 0xc1350b7a - 0xc149089c (1279 kB)
.text : 0xc1000000 - 0xc1350b7a (3394 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:320
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 1666.770 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3333.54 BogoMIPS (lpj=1666770)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
mce: CPU supports 4 MCE banks
Performance Events: AMD PMU driver.
... version: 0
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 00007fffffffffff
... fixed-purpose events: 0
... event mask: 000000000000000f
ACPI: Core revision 20100428
Enabling APIC mode: Flat. Using 1 I/O APICs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: AMD Athlon(tm) MP 2000+ stepping 02
Booting Node 0, Processors #1 Ok.
Initializing CPU#1
Brought up 2 CPUs
Total of 2 processors activated (6666.65 BogoMIPS).
devtmpfs: initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=3
PCI: Using configuration type 1 for base access
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x0d00-0x7fff] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x8100-0xffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000ccfff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xa0000000-0xfebfffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000d8000-0x000dbfff] (ignored)
pci 0000:00:00.0: reg 10: [mem 0xec000000-0xefffffff pref]
pci 0000:00:00.0: reg 14: [mem 0xe8500000-0xe8500fff pref]
pci 0000:00:00.0: reg 18: [io 0x1010-0x1013]
pci 0000:00:07.1: reg 20: [io 0xf000-0xf00f]
pci 0000:01:05.0: reg 10: [mem 0xf0000000-0xf7ffffff pref]
pci 0000:01:05.0: reg 14: [io 0x2000-0x20ff]
pci 0000:01:05.0: reg 18: [mem 0xe8020000-0xe803ffff]
pci 0000:01:05.0: reg 20: [mem 0xe8000000-0xe800ffff]
pci 0000:01:05.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:01:05.0: supports D1 D2
pci 0000:01:05.1: supports D1
pci 0000:00:01.0: PCI bridge to [bus 01-02]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe81fffff]
pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
pci 0000:02:00.0: reg 10: [mem 0xe8100000-0xe8100fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:02:00.0: PME# disabled
pci 0000:01:05.1: PCI bridge to [bus 02-02]
pci 0000:01:05.1: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:01:05.1: bridge window [mem 0xe8100000-0xe81fffff]
pci 0000:01:05.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:03:00.0: reg 10: [mem 0xe8200000-0xe8200fff]
pci 0000:03:04.0: reg 10: [io 0x3480-0x349f]
pci 0000:03:04.0: supports D1 D2
pci 0000:03:06.0: reg 10: [io 0x3000-0x30ff]
pci 0000:03:06.0: reg 14: [mem 0xe8201000-0xe82011ff]
pci 0000:03:06.0: supports D1 D2
pci 0000:03:06.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:03:06.0: PME# disabled
pci 0000:03:08.0: reg 10: [io 0x3400-0x347f]
pci 0000:03:08.0: reg 14: [mem 0xe8201400-0xe820147f]
pci 0000:03:08.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:03:08.0: supports D1 D2
pci 0000:03:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:03:08.0: PME# disabled
pci 0000:00:10.0: PCI bridge to [bus 03-03]
pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
pci 0000:00:10.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
HEST: Table is not found!
vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 32 bytes
reserve RAM buffer: 000000000009f800 - 000000000009ffff
reserve RAM buffer: 000000009fef0000 - 000000009fffffff
reserve RAM buffer: 000000009ff80000 - 000000009fffffff
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: [mem 0xfffc0000-0xffffffff] has been reserved
system 00:00: [mem 0xffc00000-0xfff7ffff] has been reserved
system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:00: [mem 0x00100000-0x9fffffff] could not be reserved
system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:06: [io 0x04d0-0x04d1] has been reserved
Switching to clocksource acpi_pm
pci 0000:00:10.0: BAR 9: assigned [mem 0xa0000000-0xa00fffff pref]
pci 0000:01:05.0: BAR 6: assigned [mem 0xe8040000-0xe805ffff pref]
pci 0000:01:05.1: PCI bridge to [bus 02-02]
pci 0000:01:05.1: bridge window [io disabled]
pci 0000:01:05.1: bridge window [mem 0xe8100000-0xe81fffff]
pci 0000:01:05.1: bridge window [mem pref disabled]
pci 0000:00:01.0: PCI bridge to [bus 01-02]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe81fffff]
pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
pci 0000:03:08.0: BAR 6: assigned [mem 0xa0000000-0xa001ffff pref]
pci 0000:00:10.0: PCI bridge to [bus 03-03]
pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
pci 0000:00:10.0: bridge window [mem 0xa0000000-0xa00fffff pref]
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:01: resource 1 [mem 0xe8000000-0xe81fffff]
pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf7ffffff pref]
pci_bus 0000:02: resource 1 [mem 0xe8100000-0xe81fffff]
pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
pci_bus 0000:03: resource 1 [mem 0xe8200000-0xe82fffff]
pci_bus 0000:03: resource 2 [mem 0xa0000000-0xa00fffff pref]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:00:00.0: BIOS failed to enable PCI standards compliance; fixing this error
pci 0000:01:05.0: Boot video device
PCI: CLS 64 bytes, default 32
audit: initializing netlink socket (disabled)
type=2000 audit(1291755100.190:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1722
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for fcrypt (fcrypt-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
ERST: Table is not found!
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Loading iSCSI transport class v2.0-870.
pata_amd 0000:00:07.1: version 0.4.1
pata_amd 0000:00:07.1: setting latency timer to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
3c59x 0000:03:08.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
3c59x: Donald Becker and others.
0000:03:08.0: 3Com PCI 3c905C Tornado at f8066400.
usbmon: debugfs is not available
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
ata1.00: ATA-6: ST340810A, 3.39, max UDMA/100
ata1.00: 78165360 sectors, multi 16: LBA
ata1.01: ATA-6: ST3160023A, 8.01, max UDMA/100
ata1.01: 312581808 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST340810A 3.39 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 0:0:1:0: Direct-Access ATA ST3160023A 8.01 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: Attached scsi generic sg1 type 0
sda:
sd 0:0:1:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
sda1 sda2 sda3
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda4
sdb: sdb1 sdb2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:1:0: [sdb] Attached SCSI disk
ata2.00: ATAPI: LITE-ON DVDRW LH-20A1H, LL0C, max UDMA/66
ata2.01: ATAPI: MATSHITA CD-RW CW-7586, 1.08, max MWDMA2
ata2.00: limited to UDMA/33 due to 40-wire cable
ata2.00: configured for UDMA/33
ata2.01: configured for MWDMA2
scsi 1:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1H LL0C PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg2 type 5
scsi 1:0:1:0: CD-ROM MATSHITA CD-RW CW-7586 1.08 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
sr 1:0:1:0: Attached scsi generic sg3 type 5
REISERFS (device sda2): found reiserfs format "3.6" with standard journal
REISERFS (device sda2): using ordered data mode
REISERFS (device sda2): journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
REISERFS (device sda2): checking transaction log (sda2)
REISERFS (device sda2): Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly on device 8:2.
devtmpfs: mounted
Freeing unused kernel memory: 348k freed
Write protecting the kernel text: 3396k
Write protecting the kernel read-only data: 1032k
udev[679]: starting version 164
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input3
ACPI: Sleep Button [SLPF]
AMD768 RNG detected
Linux agpgart interface v0.103
agpgart-amdk7 0000:00:00.0: AMD 760MP chipset
agpgart-amdk7 0000:00:00.0: AGP aperture is 64M @ 0xec000000
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram
"amd76xrom" amd76xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug?
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ohci1394 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[18] MMIO=[e8100000-e81007ff] Max Packet=[2048] IR/IT contexts=[8/8]
ACPI: acpi_idle registered with cpuidle
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
ppdev: user-space parallel port driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:03:00.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:03:00.0: OHCI Host Controller
ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:03:00.0: irq 19, io mem 0xe8200000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.35.9-smp ohci_hcd
usb usb1: SerialNumber: 0000:03:00.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
BUG: unable to handle kernel paging request at f860aaa0
IP: [<f817d282>] simple_map_write+0x82/0xbb [map_funcs]
*pde = 36a8c067 *pte = 00000000
Oops: 0002 [#1] SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:10.0/0000:03:00.0/usb1/bDeviceClass
Modules linked in: jedec_probe ohci_hcd snd_ac97_codec ppdev i2c_amd756 thermal parport_pc cfi_probe ehci_hcd gen_probe ac97_bus snd_pcm snd_timer i2c_core processor psmouse ohci1394 parport thermal_sys cfi_util snd serio_raw floppy ieee1394 amd76xrom(+) mtd chipreg map_funcs rtc_cmos rtc_core snd_page_alloc rtc_lib evdev hwmon amd_k7_agp agpgart amd_rng container button
Pid: 693, comm: modprobe Not tainted 2.6.35.9-smp #1 S2466 TIGER MPX/Unknown
EIP: 0060:[<f817d282>] EFLAGS: 00010212 CPU: 0
EIP is at simple_map_write+0x82/0xbb [map_funcs]
EAX: 000000aa EBX: 00000020 ECX: 00000008 EDX: 000000aa
ESI: f6885a48 EDI: f860aaa0 EBP: f6885a74 ESP: f6885a48
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process modprobe (pid: 693, ti=f6884000 task=f71a7a70 task.ti=f6884000)
Stack:
000000aa 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa
<0> 00000008 f6885b84 f6885a9c f6885d90 f8638ad4 000000aa 000000aa 000000aa
<0> 000000aa 000000aa 000000aa 000000aa 000000aa 000aaaa0 00000000 00000004
Call Trace:
[<f8638ad4>] ? cfi_qry_mode_on+0xc74/0x1130 [cfi_util]
[<f8822e7c>] ? jedec_probe_chip+0x6fc/0x1394 [jedec_probe]
[<f879a1c1>] ? cfi_probe_chip+0x41/0x48c [cfi_probe]
[<f875e1aa>] ? mtd_do_chip_probe+0xaa/0x358 [gen_probe]
[<c1021930>] ? do_page_fault+0x0/0x370
[<f879a00d>] ? cfi_probe+0xd/0x10 [cfi_probe]
[<f8186154>] ? do_map_probe+0x24/0x73 [chipreg]
[<f81a521a>] ? init_amd76xrom+0x21a/0x3d2 [amd76xrom]
[<c100122d>] ? do_one_initcall+0x2d/0x180
[<f81a5000>] ? init_amd76xrom+0x0/0x3d2 [amd76xrom]
[<c10614eb>] ? sys_init_module+0x9b/0x1e0
[<c10aa49d>] ? sys_write+0x3d/0x70
[<c134f83c>] ? syscall_call+0x7/0xb
Code: 7f 17 f0 83 04 24 00 8b 5d f4 8b 75 f8 8b 7d fc 89 ec 5d c3 90 8d 74 26 00 01 cf 81 fb ff 01 00 00 77 2e 89 d9 c1 e9 02 8d 75 d4 <f3> a5 89 d9 83 e1 03 74 02 f3 a4 eb ca 90 01 cf 88 07 eb c3 66
EIP: [<f817d282>] simple_map_write+0x82/0xbb [map_funcs] SS:ESP 0068:f6885a48
CR2: 00000000f860aaa0
---[ end trace 1c763f9f08138e6b ]---
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0006bb0016042789]
CA0106 0000:03:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
snd-ca0106: Model 1006 Rev 00000000 Serial 10061102
lp0: using parport0 (interrupt-driven).
lp0: console ready
eth0: setting full-duplex.
[-- Attachment #8: dmesg4-withbug --]
[-- Type: TEXT/PLAIN, Size: 22851 bytes --]
Linux version 2.6.35.9-smp (russ@bigred) (gcc version 4.5.2 20101125 (prerelease) (GCC) ) #1 SMP Tue Dec 7 20:27:42 PST 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000009fef0000 (usable)
BIOS-e820: 000000009fef0000 - 000000009feff000 (ACPI data)
BIOS-e820: 000000009feff000 - 000000009ff00000 (ACPI NVS)
BIOS-e820: 000000009ff00000 - 000000009ff80000 (usable)
BIOS-e820: 000000009ff80000 - 00000000a0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
DMI 2.3 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x9ff80 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CDFFF write-protect
CE000-DFFFF uncachable
E0000-E3FFF write-back
E4000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 080000000 mask FE0000000 write-back
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 15000-1a000
ACPI: RSDP 000f7100 00014 (v00 PTLTD )
ACPI: RSDT 9fefcf28 0002C (v01 PTLTD RSDT 06040000 LTP 00000000)
ACPI: FACP 9fefef2e 00074 (v01 AMD TECATE 06040000 PTL 000F4240)
ACPI: DSDT 9fefcf54 01FDA (v01 AMD AMDACPI 06040000 MSFT 0100000D)
ACPI: FACS 9fefffc0 00040
ACPI: APIC 9fefefa2 0005E (v01 PTLTD ? APIC 06040000 LTP 00000000)
ACPI: Local APIC address 0xfee00000
1671MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00016000 - 0001cf00
(8/32 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#1 [0001000000 - 000152e5a4] TEXT DATA BSS ==> [0001000000 - 000152e5a4]
#2 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#3 [000152f000 - 00015350f4] BRK ==> [000152f000 - 00015350f4]
#4 [0000010000 - 0000011000] TRAMPOLINE ==> [0000010000 - 0000011000]
#5 [0000011000 - 0000015000] ACPI WAKEUP ==> [0000011000 - 0000015000]
#6 [0000015000 - 0000016000] PGTABLE ==> [0000015000 - 0000016000]
#7 [0000016000 - 000001d000] BOOTMAP ==> [0000016000 - 000001d000]
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0009ff80
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0009fef0
0: 0x0009ff00 -> 0x0009ff80
On node 0 totalpages: 655103
free_area_init_node: node 0, pgdat c148c400, node_mem_map c1537200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 3344 pages used for memmap
HighMem zone: 424546 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
Allocating PCI resources starting at a0000000 (gap: a0000000:5ec00000)
setup_percpu: NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 13 pages/cpu @c2c00000 s29632 r0 d23616 u2097152
pcpu-alloc: s29632 r0 d23616 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 649983
Kernel command line: root=/dev/sda2
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0009ff80)
Memory: 2593628k/2620928k available (3394k kernel code, 26784k reserved, 1279k data, 348k init, 1711560k highmem)
virtual kernel memory layout:
fixmap : 0xfff8f000 - 0xfffff000 ( 448 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1491000 - 0xc14e8000 ( 348 kB)
.data : 0xc1350b7a - 0xc149089c (1279 kB)
.text : 0xc1000000 - 0xc1350b7a (3394 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:320
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 1666.701 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3333.40 BogoMIPS (lpj=1666701)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
mce: CPU supports 4 MCE banks
Performance Events: AMD PMU driver.
... version: 0
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 00007fffffffffff
... fixed-purpose events: 0
... event mask: 000000000000000f
ACPI: Core revision 20100428
Enabling APIC mode: Flat. Using 1 I/O APICs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: AMD Athlon(tm) MP 2000+ stepping 02
Booting Node 0, Processors #1 Ok.
Initializing CPU#1
Brought up 2 CPUs
Total of 2 processors activated (6666.31 BogoMIPS).
devtmpfs: initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=3
PCI: Using configuration type 1 for base access
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x0d00-0x7fff] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x8100-0xffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000ccfff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xa0000000-0xfebfffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000d8000-0x000dbfff] (ignored)
pci 0000:00:00.0: reg 10: [mem 0xec000000-0xefffffff pref]
pci 0000:00:00.0: reg 14: [mem 0xe8500000-0xe8500fff pref]
pci 0000:00:00.0: reg 18: [io 0x1010-0x1013]
pci 0000:00:07.1: reg 20: [io 0xf000-0xf00f]
pci 0000:01:05.0: reg 10: [mem 0xf0000000-0xf7ffffff pref]
pci 0000:01:05.0: reg 14: [io 0x2000-0x20ff]
pci 0000:01:05.0: reg 18: [mem 0xe8020000-0xe803ffff]
pci 0000:01:05.0: reg 20: [mem 0xe8000000-0xe800ffff]
pci 0000:01:05.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:01:05.0: supports D1 D2
pci 0000:01:05.1: supports D1
pci 0000:00:01.0: PCI bridge to [bus 01-02]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe81fffff]
pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
pci 0000:02:00.0: reg 10: [mem 0xe8100000-0xe8100fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:02:00.0: PME# disabled
pci 0000:01:05.1: PCI bridge to [bus 02-02]
pci 0000:01:05.1: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:01:05.1: bridge window [mem 0xe8100000-0xe81fffff]
pci 0000:01:05.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:03:00.0: reg 10: [mem 0xe8200000-0xe8200fff]
pci 0000:03:04.0: reg 10: [io 0x3480-0x349f]
pci 0000:03:04.0: supports D1 D2
pci 0000:03:06.0: reg 10: [io 0x3000-0x30ff]
pci 0000:03:06.0: reg 14: [mem 0xe8201000-0xe82011ff]
pci 0000:03:06.0: supports D1 D2
pci 0000:03:06.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:03:06.0: PME# disabled
pci 0000:03:08.0: reg 10: [io 0x3400-0x347f]
pci 0000:03:08.0: reg 14: [mem 0xe8201400-0xe820147f]
pci 0000:03:08.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:03:08.0: supports D1 D2
pci 0000:03:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:03:08.0: PME# disabled
pci 0000:00:10.0: PCI bridge to [bus 03-03]
pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
pci 0000:00:10.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
HEST: Table is not found!
vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 32 bytes
reserve RAM buffer: 000000000009f800 - 000000000009ffff
reserve RAM buffer: 000000009fef0000 - 000000009fffffff
reserve RAM buffer: 000000009ff80000 - 000000009fffffff
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: [mem 0xfffc0000-0xffffffff] has been reserved
system 00:00: [mem 0xffc00000-0xfff7ffff] has been reserved
system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:00: [mem 0x00100000-0x9fffffff] could not be reserved
system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:06: [io 0x04d0-0x04d1] has been reserved
Switching to clocksource acpi_pm
pci 0000:00:10.0: BAR 9: assigned [mem 0xa0000000-0xa00fffff pref]
pci 0000:01:05.0: BAR 6: assigned [mem 0xe8040000-0xe805ffff pref]
pci 0000:01:05.1: PCI bridge to [bus 02-02]
pci 0000:01:05.1: bridge window [io disabled]
pci 0000:01:05.1: bridge window [mem 0xe8100000-0xe81fffff]
pci 0000:01:05.1: bridge window [mem pref disabled]
pci 0000:00:01.0: PCI bridge to [bus 01-02]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe81fffff]
pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
pci 0000:03:08.0: BAR 6: assigned [mem 0xa0000000-0xa001ffff pref]
pci 0000:00:10.0: PCI bridge to [bus 03-03]
pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
pci 0000:00:10.0: bridge window [mem 0xa0000000-0xa00fffff pref]
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:01: resource 1 [mem 0xe8000000-0xe81fffff]
pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf7ffffff pref]
pci_bus 0000:02: resource 1 [mem 0xe8100000-0xe81fffff]
pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
pci_bus 0000:03: resource 1 [mem 0xe8200000-0xe82fffff]
pci_bus 0000:03: resource 2 [mem 0xa0000000-0xa00fffff pref]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:00:00.0: BIOS failed to enable PCI standards compliance; fixing this error
pci 0000:01:05.0: Boot video device
PCI: CLS 64 bytes, default 32
audit: initializing netlink socket (disabled)
type=2000 audit(1291755372.189:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1722
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for fcrypt (fcrypt-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
ERST: Table is not found!
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Loading iSCSI transport class v2.0-870.
pata_amd 0000:00:07.1: version 0.4.1
pata_amd 0000:00:07.1: setting latency timer to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
3c59x 0000:03:08.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
3c59x: Donald Becker and others.
0000:03:08.0: 3Com PCI 3c905C Tornado at f8066400.
usbmon: debugfs is not available
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
ata1.00: ATA-6: ST340810A, 3.39, max UDMA/100
ata1.00: 78165360 sectors, multi 16: LBA
ata1.01: ATA-6: ST3160023A, 8.01, max UDMA/100
ata1.01: 312581808 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST340810A 3.39 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
sd 0:0:0:0: [sda] Write Protect is off
scsi 0:0:1:0: Direct-Access ATA ST3160023A 8.01 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
sd 0:0:1:0: Attached scsi generic sg1 type 0
sda1 sda2 sda3 sda4
sd 0:0:1:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:1:0: [sdb] Attached SCSI disk
ata2.00: ATAPI: LITE-ON DVDRW LH-20A1H, LL0C, max UDMA/66
ata2.01: ATAPI: MATSHITA CD-RW CW-7586, 1.08, max MWDMA2
ata2.00: limited to UDMA/33 due to 40-wire cable
ata2.00: configured for UDMA/33
ata2.01: configured for MWDMA2
scsi 1:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1H LL0C PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg2 type 5
scsi 1:0:1:0: CD-ROM MATSHITA CD-RW CW-7586 1.08 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
sr 1:0:1:0: Attached scsi generic sg3 type 5
REISERFS (device sda2): found reiserfs format "3.6" with standard journal
REISERFS (device sda2): using ordered data mode
REISERFS (device sda2): journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
REISERFS (device sda2): checking transaction log (sda2)
REISERFS (device sda2): Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly on device 8:2.
devtmpfs: mounted
Freeing unused kernel memory: 348k freed
Write protecting the kernel text: 3396k
Write protecting the kernel read-only data: 1032k
udev[679]: starting version 164
Linux agpgart interface v0.103
agpgart-amdk7 0000:00:00.0: AMD 760MP chipset
agpgart-amdk7 0000:00:00.0: AGP aperture is 64M @ 0xec000000
AMD768 RNG detected
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input3
ACPI: Sleep Button [SLPF]
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram
"amd76xrom" amd76xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug?
ohci1394 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[18] MMIO=[e8100000-e81007ff] Max Packet=[2048] IR/IT contexts=[8/8]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:03:00.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:03:00.0: OHCI Host Controller
ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:03:00.0: irq 19, io mem 0xe8200000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.35.9-smp ohci_hcd
usb usb1: SerialNumber: 0000:03:00.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
CA0106 0000:03:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
snd-ca0106: Model 1006 Rev 00000000 Serial 10061102
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
ACPI: acpi_idle registered with cpuidle
BUG: unable to handle kernel paging request at f86aaaa0
IP: [<f8044282>] simple_map_write+0x82/0xbb [map_funcs]
*pde = 36ac8067 *pte = 00000000
Oops: 0002 [#1] SMP
last sysfs file: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/PNP0A05:00/PNP0401:00/uevent
Modules linked in: processor parport_pc thermal jedec_probe snd_ca0106 snd_rawmidi ohci_hcd snd_seq_device snd_ac97_codec ehci_hcd cfi_probe gen_probe cfi_util thermal_sys floppy ohci1394 ac97_bus snd_pcm psmouse parport amd76xrom(+) rtc_cmos mtd serio_raw evdev snd_timer container i2c_amd756 rtc_core ieee1394 i2c_core hwmon rtc_lib button amd_rng snd chipreg amd_k7_agp map_funcs snd_page_alloc agpgart
Pid: 693, comm: modprobe Not tainted 2.6.35.9-smp #1 S2466 TIGER MPX/Unknown
EIP: 0060:[<f8044282>] EFLAGS: 00010212 CPU: 0
EIP is at simple_map_write+0x82/0xbb [map_funcs]
EAX: 000000aa EBX: 00000020 ECX: 00000008 EDX: 000000aa
ESI: f6881a48 EDI: f86aaaa0 EBP: f6881a74 ESP: f6881a48
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process modprobe (pid: 693, ti=f6880000 task=f712c6e0 task.ti=f6880000)
Stack:
000000aa 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa
<0> 00000008 f6881b84 f6881a9c f6881d90 f873fad4 000000aa 000000aa 000000aa
<0> 000000aa 000000aa 000000aa 000000aa 000000aa 000aaaa0 00000000 00000004
Call Trace:
[<f873fad4>] ? cfi_qry_mode_on+0xc74/0x1130 [cfi_util]
[<f880ee7c>] ? jedec_probe_chip+0x6fc/0x1394 [jedec_probe]
[<f87541c1>] ? cfi_probe_chip+0x41/0x48c [cfi_probe]
[<f874a1aa>] ? mtd_do_chip_probe+0xaa/0x358 [gen_probe]
[<f875400d>] ? cfi_probe+0xd/0x10 [cfi_probe]
[<f8022154>] ? do_map_probe+0x24/0x73 [chipreg]
[<f824d21a>] ? init_amd76xrom+0x21a/0x3d2 [amd76xrom]
[<c100122d>] ? do_one_initcall+0x2d/0x180
[<f824d000>] ? init_amd76xrom+0x0/0x3d2 [amd76xrom]
[<c10614eb>] ? sys_init_module+0x9b/0x1e0
[<c10aa49d>] ? sys_write+0x3d/0x70
[<c134f83c>] ? syscall_call+0x7/0xb
Code: 7f 17 f0 83 04 24 00 8b 5d f4 8b 75 f8 8b 7d fc 89 ec 5d c3 90 8d 74 26 00 01 cf 81 fb ff 01 00 00 77 2e 89 d9 c1 e9 02 8d 75 d4 <f3> a5 89 d9 83 e1 03 74 02 f3 a4 eb ca 90 01 cf 88 07 eb c3 66
EIP: [<f8044282>] simple_map_write+0x82/0xbb [map_funcs] SS:ESP 0068:f6881a48
CR2: 00000000f86aaaa0
---[ end trace 91357a6db38469af ]---
ppdev: user-space parallel port driver
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0006bb0016042789]
lp0: using parport0 (interrupt-driven).
lp0: console ready
eth0: setting full-duplex.
[-- Attachment #9: cpuinfo_from_test_partition --]
[-- Type: TEXT/PLAIN, Size: 1097 bytes --]
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 6
model name : AMD Athlon(tm) MP 2000+
stepping : 2
cpu MHz : 1666.701
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mp mmxext 3dnowext 3dnow
bogomips : 3333.40
clflush size : 32
cache_alignment : 32
address sizes : 34 bits physical, 32 bits virtual
power management: ts
processor : 1
vendor_id : AuthenticAMD
cpu family : 6
model : 6
model name : AMD Athlon(tm) Processor
stepping : 2
cpu MHz : 1666.701
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mp mmxext 3dnowext 3dnow
bogomips : 3332.91
clflush size : 32
cache_alignment : 32
address sizes : 34 bits physical, 32 bits virtual
power management: ts
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.35.9 bug shown in dmesg (fwd)
2010-12-30 20:57 2.6.35.9 bug shown in dmesg (fwd) Russell Whitaker
@ 2011-01-03 23:00 ` Stanislaw Gruszka
2011-01-06 6:21 ` Russell Whitaker
0 siblings, 1 reply; 8+ messages in thread
From: Stanislaw Gruszka @ 2011-01-03 23:00 UTC (permalink / raw)
To: Russell Whitaker; +Cc: linux-ide
Hi
On Thu, Dec 30, 2010 at 12:57:41PM -0800, Russell Whitaker wrote:
> Since sending the email below found some more info:
>
> Tried several kernels from 2.6.32.16 up - same problem.
>
> If I build kernel using "ATA/ATAPI/MFM/RLL=y" and right choices in
> sub-menu (and fstab with hd...) There is no problem.
>
> Making change to "serial ATA (prod) and parallel ATA (experimental)=y"
> the computer crashes during boot-up about 1/3 of the time.
>
> Hardware:
> Tyan mb s2466 Tiger MPX (2 cpu)
> 2 segate hd on primary ide
>
> If you send me a patch, will try it and let you know what happens.
BUG is from amd76xrom MTD driver, there is some resources conflict.
Below patch should fix oops in simple_map_write(), but not the conflict.
Please apply it to confirm oops fix and to show us contents of
/proc/iomem on ATA/ATAPI/MFM/RLL and on experimental parallel ATA
for compare.
Stanislaw
---
>From 8bcfe30f1c52b1fe61b2885731421ab5998f0629 Mon Sep 17 00:00:00 2001
From: Stanislaw Gruszka <stf_xl@wp.pl>
Date: Mon, 3 Jan 2011 23:32:34 +0100
Subject: [PATCH] amd76xrom: fix oops at boot when resources are not available
For some unknown reason resources needed by amd76xrom driver can not be
available. Instead of return error, driver crash the kernel with
messages like below. Patch fix that.
amd76xrom" amd76xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug?
BUG: unable to handle kernel paging request at f862aaa0
IP: [<f8120282>] simple_map_write+0x82/0xbb [map_funcs]
*pde = 36ad2067 *pte = 00000000
Oops: 0002 [#1] SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:07.1/host0/target0:0:1/0:0:1:0/block/sdb/removable
Modules linked in: rtc_core thermal_sys jedec_probe serio_raw rtc_lib snd_ca0106 snd_rawmidi snd_seq_device snd_ac97_codec cfi_probe hwmon gen_probe cfi_util amd76xrom(+) ac97_bus snd_pcm snd_timer container mtd amd_rng snd amd_k7_agp chipreg map_funcs
+snd_page_alloc agpgart button
Pid: 690, comm: modprobe Not tainted 2.6.35.9-smp #1 S2466 TIGER MPX/Unknown
EIP: 0060:[<f8120282>] EFLAGS: 00010212 CPU: 1
EIP is at simple_map_write+0x82/0xbb [map_funcs]
EAX: 000000aa EBX: 00000020 ECX: 00000008 EDX: 000000aa
ESI: f6869a48 EDI: f862aaa0 EBP: f6869a74 ESP: f6869a48
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process modprobe (pid: 690, ti=f6868000 task=f738ecb0 task.ti=f6868000)
Stack:
000000aa 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa
<0> 00000008 f6869b84 f6869a9c f6869d90 f8159ad4 000000aa 000000aa 000000aa
<0> 000000aa 000000aa 000000aa 000000aa 000000aa 000aaaa0 00000000 00000004
Call Trace:
[<f8159ad4>] ? cfi_qry_mode_on+0xc74/0x1130 [cfi_util]
[<f864be7c>] ? jedec_probe_chip+0x6fc/0x1394 [jedec_probe]
[<f819c1c1>] ? cfi_probe_chip+0x41/0x48c [cfi_probe]
[<f815d1aa>] ? mtd_do_chip_probe+0xaa/0x358 [gen_probe]
[<f819c00d>] ? cfi_probe+0xd/0x10 [cfi_probe]
[<f8129154>] ? do_map_probe+0x24/0x73 [chipreg]
[<f812621a>] ? init_amd76xrom+0x21a/0x3d2 [amd76xrom]
[<c100122d>] ? do_one_initcall+0x2d/0x180
[<f8126000>] ? init_amd76xrom+0x0/0x3d2 [amd76xrom]
[<c10614eb>] ? sys_init_module+0x9b/0x1e0
[<c10aa49d>] ? sys_write+0x3d/0x70
[<c134f83c>] ? syscall_call+0x7/0xb
Code: 7f 17 f0 83 04 24 00 8b 5d f4 8b 75 f8 8b 7d fc 89 ec 5d c3 90 8d 74 26 00 01 cf 81 fb ff 01 00 00 77 2e 89 d9 c1 e9 02 8d 75 d4 <f3> a5 89 d9 83 e1 03 74 02 f3 a4 eb ca 90 01 cf 88 07 eb c3 66
EIP: [<f8120282>] simple_map_write+0x82/0xbb [map_funcs] SS:ESP 0068:f6869a48
CR2: 00000000f862aaa0
Reported-by: Russell Whitaker <russ@ashlandhome.net>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
---
drivers/mtd/maps/amd76xrom.c | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/drivers/mtd/maps/amd76xrom.c b/drivers/mtd/maps/amd76xrom.c
index 19fe92d..370509a 100644
--- a/drivers/mtd/maps/amd76xrom.c
+++ b/drivers/mtd/maps/amd76xrom.c
@@ -154,6 +154,7 @@ static int __devinit amd76xrom_init_one (struct pci_dev *pdev,
__func__,
(unsigned long long)window->rsrc.start,
(unsigned long long)window->rsrc.end);
+ return -EBUSY;
}
--
1.7.0.4
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: 2.6.35.9 bug shown in dmesg (fwd)
2011-01-03 23:00 ` Stanislaw Gruszka
@ 2011-01-06 6:21 ` Russell Whitaker
2011-01-06 16:19 ` Stanislaw Gruszka
0 siblings, 1 reply; 8+ messages in thread
From: Russell Whitaker @ 2011-01-06 6:21 UTC (permalink / raw)
To: Stanislaw Gruszka; +Cc: linux-ide
On Tue, 4 Jan 2011, Stanislaw Gruszka wrote:
> Hi
>
> On Thu, Dec 30, 2010 at 12:57:41PM -0800, Russell Whitaker wrote:
>> Since sending the email below found some more info:
>>
>> Tried several kernels from 2.6.32.16 up - same problem.
>>
>> If I build kernel using "ATA/ATAPI/MFM/RLL=y" and right choices in
>> sub-menu (and fstab with hd...) There is no problem.
>>
>> Making change to "serial ATA (prod) and parallel ATA (experimental)=y"
>> the computer crashes during boot-up about 1/3 of the time.
>>
>> Hardware:
>> Tyan mb s2466 Tiger MPX (2 cpu)
>> 2 segate hd on primary ide
>>
>> If you send me a patch, will try it and let you know what happens.
>
> BUG is from amd76xrom MTD driver, there is some resources conflict.
> Below patch should fix oops in simple_map_write(), but not the conflict.
> Please apply it to confirm oops fix and to show us contents of
> /proc/iomem on ATA/ATAPI/MFM/RLL and on experimental parallel ATA
> for compare.
>
> Stanislaw
>
> ---
>> From 8bcfe30f1c52b1fe61b2885731421ab5998f0629 Mon Sep 17 00:00:00 2001
> From: Stanislaw Gruszka <stf_xl@wp.pl>
> Date: Mon, 3 Jan 2011 23:32:34 +0100
> Subject: [PATCH] amd76xrom: fix oops at boot when resources are not available
>
> For some unknown reason resources needed by amd76xrom driver can not be
> available. Instead of return error, driver crash the kernel with
> messages like below. Patch fix that.
>
> amd76xrom" amd76xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug?
Sorry, in my case that's the wrong bug. First found the bug using
Slackware-current. So I stripped down his config file by removing most
of what I can't use, recompiled, and the bug was still there.
I'm not using amd76xrom so went into a MTD submenu and changed it to not
set, etc, and found the bug is still there.
The bug is in pata (experimental). By comparison, ide (depreciated) has
been working solid for years.
comparing config for linux-2.6.35.10, ide vs pata and no other changes:
4c4
< # Tue Jan 4 19:12:25 2011
---
> # Tue Jan 4 12:27:07 2011
1057,1119c1057
< CONFIG_IDE=y
<
< #
< # Please see Documentation/ide/ide.txt for help/info on IDE drives
< #
< CONFIG_IDE_XFER_MODE=y
< CONFIG_IDE_TIMINGS=y
< CONFIG_IDE_ATAPI=y
< # CONFIG_BLK_DEV_IDE_SATA is not set
< CONFIG_IDE_GD=y
< CONFIG_IDE_GD_ATA=y
< CONFIG_IDE_GD_ATAPI=y
< CONFIG_BLK_DEV_IDECD=y
< CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
< # CONFIG_BLK_DEV_IDETAPE is not set
< CONFIG_BLK_DEV_IDEACPI=y
< # CONFIG_IDE_TASK_IOCTL is not set
< CONFIG_IDE_PROC_FS=y
<
< #
< # IDE chipset support/bugfixes
< #
< # CONFIG_IDE_GENERIC is not set
< # CONFIG_BLK_DEV_PLATFORM is not set
< # CONFIG_BLK_DEV_CMD640 is not set
< # CONFIG_BLK_DEV_IDEPNP is not set
< CONFIG_BLK_DEV_IDEDMA_SFF=y
<
< #
< # PCI IDE chipsets support
< #
< CONFIG_BLK_DEV_IDEPCI=y
< CONFIG_IDEPCI_PCIBUS_ORDER=y
< # CONFIG_BLK_DEV_GENERIC is not set
< # CONFIG_BLK_DEV_RZ1000 is not set
< CONFIG_BLK_DEV_IDEDMA_PCI=y
< # CONFIG_BLK_DEV_AEC62XX is not set
< # CONFIG_BLK_DEV_ALI15X3 is not set
< CONFIG_BLK_DEV_AMD74XX=y
< # CONFIG_BLK_DEV_ATIIXP is not set
< # CONFIG_BLK_DEV_CMD64X is not set
< # CONFIG_BLK_DEV_TRIFLEX is not set
< # CONFIG_BLK_DEV_CS5530 is not set
< # CONFIG_BLK_DEV_CS5535 is not set
< # CONFIG_BLK_DEV_CS5536 is not set
< # CONFIG_BLK_DEV_HPT366 is not set
< # CONFIG_BLK_DEV_JMICRON is not set
< # CONFIG_BLK_DEV_SC1200 is not set
< # CONFIG_BLK_DEV_PIIX is not set
< # CONFIG_BLK_DEV_IT8172 is not set
< # CONFIG_BLK_DEV_IT8213 is not set
< # CONFIG_BLK_DEV_IT821X is not set
< # CONFIG_BLK_DEV_NS87415 is not set
< # CONFIG_BLK_DEV_PDC202XX_OLD is not set
< # CONFIG_BLK_DEV_PDC202XX_NEW is not set
< # CONFIG_BLK_DEV_SVWKS is not set
< # CONFIG_BLK_DEV_SIIMAGE is not set
< # CONFIG_BLK_DEV_SIS5513 is not set
< # CONFIG_BLK_DEV_SLC90E66 is not set
< # CONFIG_BLK_DEV_TRM290 is not set
< # CONFIG_BLK_DEV_VIA82CXXX is not set
< # CONFIG_BLK_DEV_TC86C001 is not set
< CONFIG_BLK_DEV_IDEDMA=y
---
> # CONFIG_IDE is not set
1154a1093
> CONFIG_SCSI_SAS_ATA=y
1161c1100,1183
< # CONFIG_ATA is not set
---
> CONFIG_ATA=y
> # CONFIG_ATA_NONSTANDARD is not set
> CONFIG_ATA_VERBOSE_ERROR=y
> CONFIG_ATA_ACPI=y
> # CONFIG_SATA_PMP is not set
>
> #
> # Controllers with non-SFF native interface
> #
> # CONFIG_SATA_AHCI is not set
> # CONFIG_SATA_AHCI_PLATFORM is not set
> # CONFIG_SATA_INIC162X is not set
> # CONFIG_SATA_SIL24 is not set
> CONFIG_ATA_SFF=y
>
> #
> # SFF controllers with custom DMA interface
> #
> # CONFIG_PDC_ADMA is not set
> # CONFIG_SATA_QSTOR is not set
> CONFIG_ATA_BMDMA=y
>
> #
> # SATA SFF controllers with BMDMA
> #
> # CONFIG_ATA_PIIX is not set
> # CONFIG_SATA_MV is not set
> # CONFIG_SATA_NV is not set
> # CONFIG_SATA_PROMISE is not set
> # CONFIG_SATA_SIL is not set
> # CONFIG_SATA_SIS is not set
> # CONFIG_SATA_SVW is not set
> # CONFIG_SATA_ULI is not set
> # CONFIG_SATA_VIA is not set
> # CONFIG_SATA_VITESSE is not set
>
> #
> # PATA SFF controllers with BMDMA
> #
> # CONFIG_PATA_ALI is not set
> CONFIG_PATA_AMD=y
> # CONFIG_PATA_ARTOP is not set
> # CONFIG_PATA_ATIIXP is not set
> # CONFIG_PATA_ATP867X is not set
> # CONFIG_PATA_CMD64X is not set
> # CONFIG_PATA_CS5520 is not set
> # CONFIG_PATA_CS5530 is not set
> # CONFIG_PATA_CS5536 is not set
> # CONFIG_PATA_EFAR is not set
> # CONFIG_PATA_HPT366 is not set
> # CONFIG_PATA_HPT37X is not set
> # CONFIG_PATA_HPT3X2N is not set
> # CONFIG_PATA_HPT3X3 is not set
> # CONFIG_PATA_IT821X is not set
> # CONFIG_PATA_JMICRON is not set
> # CONFIG_PATA_MARVELL is not set
> # CONFIG_PATA_NETCELL is not set
> # CONFIG_PATA_NINJA32 is not set
> # CONFIG_PATA_NS87415 is not set
> # CONFIG_PATA_OLDPIIX is not set
> # CONFIG_PATA_PDC2027X is not set
> # CONFIG_PATA_PDC_OLD is not set
> # CONFIG_PATA_RDC is not set
> # CONFIG_PATA_SC1200 is not set
> # CONFIG_PATA_SCH is not set
> # CONFIG_PATA_SERVERWORKS is not set
> CONFIG_PATA_SIL680=y
> # CONFIG_PATA_SIS is not set
> # CONFIG_PATA_TRIFLEX is not set
> # CONFIG_PATA_VIA is not set
> # CONFIG_PATA_WINBOND is not set
>
> #
> # PIO-only SFF controllers
> #
> # CONFIG_PATA_MPIIX is not set
> # CONFIG_PATA_NS87410 is not set
> # CONFIG_PATA_RZ1000 is not set
>
> #
> # Generic fallback / legacy drivers
> #
> CONFIG_PATA_ACPI=y
> CONFIG_ATA_GENERIC=y
2088d2109
< # CONFIG_LEDS_TRIGGER_IDE_DISK is not set
Here are my thoughts on what's happening:
Typical time for one revolution of the hard drive's platter is 8.3
milliseconds. Let's assume setup takes time t to initialize the hard
drive(s). Then the actual time for setup to be completed is a random
number between time t and time t plus 8.3 milliseconds.
During boot and measuring from the same begining of time t, let's
assume the second cpu tries to access the hard drive at time t plus
4 milliseconds. Now the computer boots up corectly half the time and
shows a bug the other half.
Since the bug is not in ide (depreciated) there must be some small
easily overlooked detail that was not brought forward.
Hope this helps,
Russ
> BUG: unable to handle kernel paging request at f862aaa0
> IP: [<f8120282>] simple_map_write+0x82/0xbb [map_funcs]
> *pde = 36ad2067 *pte = 00000000
> Oops: 0002 [#1] SMP
> last sysfs file: /sys/devices/pci0000:00/0000:00:07.1/host0/target0:0:1/0:0:1:0/block/sdb/removable
> Modules linked in: rtc_core thermal_sys jedec_probe serio_raw rtc_lib snd_ca0106 snd_rawmidi snd_seq_device snd_ac97_codec cfi_probe hwmon gen_probe cfi_util amd76xrom(+) ac97_bus snd_pcm snd_timer container mtd amd_rng snd amd_k7_agp chipreg map_funcs
> +snd_page_alloc agpgart button
>
> Pid: 690, comm: modprobe Not tainted 2.6.35.9-smp #1 S2466 TIGER MPX/Unknown
> EIP: 0060:[<f8120282>] EFLAGS: 00010212 CPU: 1
> EIP is at simple_map_write+0x82/0xbb [map_funcs]
> EAX: 000000aa EBX: 00000020 ECX: 00000008 EDX: 000000aa
> ESI: f6869a48 EDI: f862aaa0 EBP: f6869a74 ESP: f6869a48
> DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
> Process modprobe (pid: 690, ti=f6868000 task=f738ecb0 task.ti=f6868000)
> Stack:
> 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa
> <0> 00000008 f6869b84 f6869a9c f6869d90 f8159ad4 000000aa 000000aa 000000aa
> <0> 000000aa 000000aa 000000aa 000000aa 000000aa 000aaaa0 00000000 00000004
> Call Trace:
> [<f8159ad4>] ? cfi_qry_mode_on+0xc74/0x1130 [cfi_util]
> [<f864be7c>] ? jedec_probe_chip+0x6fc/0x1394 [jedec_probe]
> [<f819c1c1>] ? cfi_probe_chip+0x41/0x48c [cfi_probe]
> [<f815d1aa>] ? mtd_do_chip_probe+0xaa/0x358 [gen_probe]
> [<f819c00d>] ? cfi_probe+0xd/0x10 [cfi_probe]
> [<f8129154>] ? do_map_probe+0x24/0x73 [chipreg]
> [<f812621a>] ? init_amd76xrom+0x21a/0x3d2 [amd76xrom]
> [<c100122d>] ? do_one_initcall+0x2d/0x180
> [<f8126000>] ? init_amd76xrom+0x0/0x3d2 [amd76xrom]
> [<c10614eb>] ? sys_init_module+0x9b/0x1e0
> [<c10aa49d>] ? sys_write+0x3d/0x70
> [<c134f83c>] ? syscall_call+0x7/0xb
> Code: 7f 17 f0 83 04 24 00 8b 5d f4 8b 75 f8 8b 7d fc 89 ec 5d c3 90 8d 74 26 00 01 cf 81 fb ff 01 00 00 77 2e 89 d9 c1 e9 02 8d 75 d4 <f3> a5 89 d9 83 e1 03 74 02 f3 a4 eb ca 90 01 cf 88 07 eb c3 66
> EIP: [<f8120282>] simple_map_write+0x82/0xbb [map_funcs] SS:ESP 0068:f6869a48
> CR2: 00000000f862aaa0
>
> Reported-by: Russell Whitaker <russ@ashlandhome.net>
> Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
> ---
> drivers/mtd/maps/amd76xrom.c | 1 +
> 1 files changed, 1 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/mtd/maps/amd76xrom.c b/drivers/mtd/maps/amd76xrom.c
> index 19fe92d..370509a 100644
> --- a/drivers/mtd/maps/amd76xrom.c
> +++ b/drivers/mtd/maps/amd76xrom.c
> @@ -154,6 +154,7 @@ static int __devinit amd76xrom_init_one (struct pci_dev *pdev,
> __func__,
> (unsigned long long)window->rsrc.start,
> (unsigned long long)window->rsrc.end);
> + return -EBUSY;
> }
>
>
> --
> 1.7.0.4
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.35.9 bug shown in dmesg (fwd)
2011-01-06 6:21 ` Russell Whitaker
@ 2011-01-06 16:19 ` Stanislaw Gruszka
2011-01-06 19:09 ` Russell Whitaker
0 siblings, 1 reply; 8+ messages in thread
From: Stanislaw Gruszka @ 2011-01-06 16:19 UTC (permalink / raw)
To: Russell Whitaker; +Cc: linux-ide
On Wed, Jan 05, 2011 at 10:21:21PM -0800, Russell Whitaker wrote:
> >For some unknown reason resources needed by amd76xrom driver can not be
> >available. Instead of return error, driver crash the kernel with
> >messages like below. Patch fix that.
> >
> >amd76xrom" amd76xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug?
>
> Sorry, in my case that's the wrong bug. First found the bug using
> Slackware-current. So I stripped down his config file by removing
> most of what I can't use, recompiled, and the bug was still there.
>
> I'm not using amd76xrom so went into a MTD submenu and changed it to
> not set, etc, and found the bug is still there.
I do not see any other problems except that one:
BUG: unable to handle kernel paging request at f862aaa0
IP: [<f8120282>] simple_map_write+0x82/0xbb [map_funcs]
in dmesg's you provided in the first email. That BUG is from amd75xrom
driver. Does dmesg without MTD compiled show something different?
And this is also not clear for me from your first email, crash happened
every time with pata or randomly?
Stanislaw
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.35.9 bug shown in dmesg (fwd)
2011-01-06 16:19 ` Stanislaw Gruszka
@ 2011-01-06 19:09 ` Russell Whitaker
2011-01-07 20:32 ` Stanislaw Gruszka
0 siblings, 1 reply; 8+ messages in thread
From: Russell Whitaker @ 2011-01-06 19:09 UTC (permalink / raw)
To: Stanislaw Gruszka; +Cc: linux-ide
On Thu, 6 Jan 2011, Stanislaw Gruszka wrote:
> On Wed, Jan 05, 2011 at 10:21:21PM -0800, Russell Whitaker wrote:
>>> For some unknown reason resources needed by amd76xrom driver can not be
>>> available. Instead of return error, driver crash the kernel with
>>> messages like below. Patch fix that.
>>>
>>> amd76xrom" amd76xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug?
>>
>> Sorry, in my case that's the wrong bug. First found the bug using
>> Slackware-current. So I stripped down his config file by removing
>> most of what I can't use, recompiled, and the bug was still there.
>>
>> I'm not using amd76xrom so went into a MTD submenu and changed it to
>> not set, etc, and found the bug is still there.
>
> I do not see any other problems except that one:
>
> BUG: unable to handle kernel paging request at f862aaa0
> IP: [<f8120282>] simple_map_write+0x82/0xbb [map_funcs]
>
> in dmesg's you provided in the first email. That BUG is from amd75xrom
> driver. Does dmesg without MTD compiled show something different?
The " - kernel bug?" line is gone.
> And this is also not clear for me from your first email, crash happened
> every time with pata or randomly?
There are two bugs. In order to reduce the problem to only one bug I
complied 2.6.35.10-smp without MTD's 4 drivers where the name starts
with "bios" and also compiled with pata.
Result, first four attempts at booting: oops 3, success 1.
To verify the problem is in pata I then replaced the pata code with the
ATA (depreciated) code, with no other changes, and recompiled.
Result, all attempts at booting: success every time.
(note: changing the kernel also means changing /etc/fstab to match)
Russ
>
> Stanislaw
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.35.9 bug shown in dmesg (fwd)
2011-01-06 19:09 ` Russell Whitaker
@ 2011-01-07 20:32 ` Stanislaw Gruszka
2011-02-14 2:50 ` Russell Whitaker
0 siblings, 1 reply; 8+ messages in thread
From: Stanislaw Gruszka @ 2011-01-07 20:32 UTC (permalink / raw)
To: Russell Whitaker; +Cc: linux-ide
On Thu, Jan 06, 2011 at 11:09:21AM -0800, Russell Whitaker wrote:
> >>Sorry, in my case that's the wrong bug. First found the bug using
> >>Slackware-current. So I stripped down his config file by removing
> >>most of what I can't use, recompiled, and the bug was still there.
> >>
> >>I'm not using amd76xrom so went into a MTD submenu and changed it to
> >>not set, etc, and found the bug is still there.
> >
> >I do not see any other problems except that one:
> >
> > BUG: unable to handle kernel paging request at f862aaa0
> > IP: [<f8120282>] simple_map_write+0x82/0xbb [map_funcs]
> >
> >in dmesg's you provided in the first email. That BUG is from amd75xrom
> >driver. Does dmesg without MTD compiled show something different?
>
> The " - kernel bug?" line is gone.
???
> >And this is also not clear for me from your first email, crash happened
> >every time with pata or randomly?
>
> There are two bugs. In order to reduce the problem to only one bug I
> complied 2.6.35.10-smp without MTD's 4 drivers where the name starts
> with "bios" and also compiled with pata.
>
> Result, first four attempts at booting: oops 3, success 1.
Ok, but on all dmesgs in your first email there was no oops
other than MTD one. If you want to have pata bug fixed, you need
to show where the problem is.
Stanislaw
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.35.9 bug shown in dmesg (fwd)
2011-01-07 20:32 ` Stanislaw Gruszka
@ 2011-02-14 2:50 ` Russell Whitaker
2011-02-14 17:31 ` Stanislaw Gruszka
0 siblings, 1 reply; 8+ messages in thread
From: Russell Whitaker @ 2011-02-14 2:50 UTC (permalink / raw)
To: Stanislaw Gruszka; +Cc: linux-ide
[-- Attachment #1: Type: TEXT/PLAIN, Size: 520 bytes --]
On Fri, 7 Jan 2011, Stanislaw Gruszka wrote:
[..]
>
> Ok, but on all dmesgs in your first email there was no oops
> other than MTD one. If you want to have pata bug fixed, you need
> to show where the problem is.
>
> Stanislaw
>
Ok, you are right. Somewhat started over and now got a saved "dmesg"
with the newer kernel. Copy of dmesg attached.
Background info:
motherboard: Tyan Tiger MPX, 2 AMD cpu's
software: Slackware-current 2/14/2011, "A" series
Selected Huge-SMP kernel
Thank you,
Russ
[-- Attachment #2: dmesg --]
[-- Type: TEXT/PLAIN, Size: 31783 bytes --]
xe820147f]
[ 0.139723] pci 0000:03:08.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.139745] pci 0000:03:08.0: supports D1 D2
[ 0.139749] pci 0000:03:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.139755] pci 0000:03:08.0: PME# disabled
[ 0.139793] pci 0000:00:10.0: PCI bridge to [bus 03-03]
[ 0.139867] pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
[ 0.139873] pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
[ 0.139879] pci 0000:00:10.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.139892] pci_bus 0000:00: on NUMA node 0
[ 0.139899] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.140058] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 0.140136] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT]
[ 0.144214] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
[ 0.145407] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *0, disabled.
[ 0.145936] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
[ 0.146434] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
[ 0.146781] HEST: Table is not found!
[ 0.147132] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.147136] vgaarb: loaded
[ 0.147379] SCSI subsystem initialized
[ 0.148118] libata version 3.00 loaded.
[ 0.148118] usbcore: registered new interface driver usbfs
[ 0.148139] usbcore: registered new interface driver hub
[ 0.149059] usbcore: registered new device driver usb
[ 0.166966] raid6: int32x1 707 MB/s
[ 0.184004] raid6: int32x2 628 MB/s
[ 0.201050] raid6: int32x4 511 MB/s
[ 0.218015] raid6: int32x8 496 MB/s
[ 0.234951] raid6: mmxx1 1320 MB/s
[ 0.251958] raid6: mmxx2 2156 MB/s
[ 0.269013] raid6: sse1x1 460 MB/s
[ 0.285969] raid6: sse1x2 917 MB/s
[ 0.286002] raid6: using algorithm sse1x2 (917 MB/s)
[ 0.286091] PCI: Using ACPI for IRQ routing
[ 0.286168] PCI: pci_cache_line_size set to 32 bytes
[ 0.286243] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[ 0.286250] reserve RAM buffer: 000000009fef0000 - 000000009fffffff
[ 0.286255] reserve RAM buffer: 000000009ff80000 - 000000009fffffff
[ 0.293067] pnp: PnP ACPI init
[ 0.293192] ACPI: bus type pnp registered
[ 0.299162] pnp: PnP ACPI: found 13 devices
[ 0.299162] ACPI: ACPI bus type pnp unregistered
[ 0.299185] system 00:00: [mem 0xfffc0000-0xffffffff] has been reserved
[ 0.299261] system 00:00: [mem 0xffc00000-0xfff7ffff] has been reserved
[ 0.299336] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.299411] system 00:00: [mem 0x00100000-0x9fffffff] could not be reserved
[ 0.299485] system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.299568] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.343429] Switching to clocksource acpi_pm
[ 0.343612] pci 0000:00:10.0: BAR 9: assigned [mem 0xa0000000-0xa00fffff pref]
[ 0.343721] pci 0000:01:05.0: BAR 6: assigned [mem 0xe8040000-0xe805ffff pref]
[ 0.343828] pci 0000:01:05.1: PCI bridge to [bus 02-02]
[ 0.343900] pci 0000:01:05.1: bridge window [io disabled]
[ 0.343978] pci 0000:01:05.1: bridge window [mem 0xe8100000-0xe81fffff]
[ 0.343999] pci 0000:01:05.1: bridge window [mem pref disabled]
[ 0.343999] pci 0000:00:01.0: PCI bridge to [bus 01-02]
[ 0.343999] pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
[ 0.343999] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe81fffff]
[ 0.343999] pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
[ 0.343999] pci 0000:03:08.0: BAR 6: assigned [mem 0xa0000000-0xa001ffff pref]
[ 0.344051] pci 0000:00:10.0: PCI bridge to [bus 03-03]
[ 0.344123] pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
[ 0.344198] pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
[ 0.344286] pci 0000:00:10.0: bridge window [mem 0xa0000000-0xa00fffff pref]
[ 0.344422] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.344426] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.344431] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.344435] pci_bus 0000:01: resource 1 [mem 0xe8000000-0xe81fffff]
[ 0.344439] pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf7ffffff pref]
[ 0.344444] pci_bus 0000:02: resource 1 [mem 0xe8100000-0xe81fffff]
[ 0.344448] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
[ 0.344452] pci_bus 0000:03: resource 1 [mem 0xe8200000-0xe82fffff]
[ 0.344456] pci_bus 0000:03: resource 2 [mem 0xa0000000-0xa00fffff pref]
[ 0.344538] NET: Registered protocol family 2
[ 0.344696] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.345309] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.348005] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.349385] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.349464] TCP reno registered
[ 0.349540] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.349650] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.349962] NET: Registered protocol family 1
[ 0.350235] RPC: Registered udp transport module.
[ 0.350318] RPC: Registered tcp transport module.
[ 0.350388] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.350479] pci 0000:00:00.0: BIOS failed to enable PCI standards compliance; fixing this error
[ 0.350613] pci 0000:01:05.0: Boot video device
[ 0.350671] PCI: CLS 64 bytes, default 32
[ 0.353746] audit: initializing netlink socket (disabled)
[ 0.353850] type=2000 audit(1297557217.353:1): initialized
[ 0.354320] highmem bounce pool size: 64 pages
[ 0.361087] VFS: Disk quotas dquot_6.5.2
[ 0.361328] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.362055] DLM (built Feb 7 2011 23:48:44) installed
[ 0.364709] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.365518] NTFS driver 2.1.29 [Flags: R/W].
[ 0.365880] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 0.366491] JFS: nTxBlock = 8192, nTxLock = 65536
[ 0.376470] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[ 0.378105] SGI XFS Quota Management subsystem
[ 0.378185] OCFS2 1.5.0
[ 0.378740] ocfs2: Registered cluster interface o2cb
[ 0.379021] ocfs2: Registered cluster interface user
[ 0.379094] OCFS2 DLMFS 1.5.0
[ 0.379391] OCFS2 User DLM kernel interface loaded
[ 0.379464] OCFS2 Node Manager 1.5.0
[ 0.379841] OCFS2 DLM 1.5.0
[ 0.380557] Btrfs loaded
[ 0.381869] Slow work thread pool: Starting up
[ 0.382054] Slow work thread pool: Ready
[ 0.382138] GFS2 (built Feb 7 2011 23:49:10) installed
[ 0.382233] msgmni has been set to 1679
[ 0.382724] alg: No test for cipher_null (cipher_null-generic)
[ 0.382884] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[ 0.383077] alg: No test for digest_null (digest_null-generic)
[ 0.383216] alg: No test for compress_null (compress_null-generic)
[ 0.385396] alg: No test for fcrypt (fcrypt-generic)
[ 0.389574] alg: No test for stdrng (krng)
[ 0.389668] async_tx: api initialized (async)
[ 0.390025] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.390134] io scheduler noop registered
[ 0.390203] io scheduler deadline registered
[ 0.390360] io scheduler cfq registered (default)
[ 0.390976] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.391787] ERST: Table is not found!
[ 0.391871] isapnp: Scanning for PnP cards...
[ 0.748787] isapnp: No Plug & Play device found
[ 0.757359] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.002192] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.246191] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.247234] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.247674] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.248513] Floppy drive(s): fd0 is 1.44M
[ 1.262829] FDC 0 is a post-1991 82077
[ 1.268840] brd: module loaded
[ 1.271293] loop: module loaded
[ 1.271365] Compaq SMART2 Driver (v 2.6.0)
[ 1.271671] HP CISS Driver (v 3.6.20)
[ 1.273808] Loading iSCSI transport class v2.0-870.
[ 1.275357] fnic: Cisco FCoE HBA Driver, ver 1.4.0.145
[ 1.279698] Adaptec aacraid driver 1.1-5[26400]-ms
[ 1.280141] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[ 1.280789] scsi: <fdomain> Detection failed (no card)
[ 1.280883] sym53c416.c: Version 1.0.0-ac
[ 1.280978] qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options
[ 1.281192] QLogic Fibre Channel HBA Driver: 8.03.02-k2
[ 1.281586] iscsi: registered transport (qla4xxx)
[ 1.281763] QLogic iSCSI HBA Driver
[ 1.281832] Emulex LightPulse Fibre Channel SCSI driver 8.3.12
[ 1.281904] Copyright(c) 2004-2009 Emulex. All rights reserved.
[ 1.282109] Brocade BFA FC/FCOE SCSI driver - version: 2.1.2.1
[ 1.304056] Failed initialization of WD-7000 SCSI card!
[ 1.355584] DC390: clustering now enabled by default. If you get problems load
[ 1.355690] with "disable_clustering=1" and report to maintainers
[ 1.355997] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 1.356318] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 1.356498] megasas: 00.00.04.17.1-rc1 Thu. Oct. 29, 11:41:51 PST 2009
[ 1.356688] mpt2sas version 05.100.00.02 loaded
[ 1.357115] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 1.357492] 3ware Storage Controller device driver for Linux v1.26.02.003.
[ 1.357665] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014.
[ 1.357884] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000.
[ 1.358101] ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
[ 1.358325] RocketRAID 3xxx/4xxx Controller driver v1.6 (090910)
[ 1.358500] stex: Promise SuperTrak EX Driver version: 4.6.0000.4
[ 1.359002] st: Version 20081215, fixed bufsize 32768, s/g segs 256
[ 1.361769] pata_amd 0000:00:07.1: version 0.4.1
[ 1.361889] pata_amd 0000:00:07.1: setting latency timer to 64
[ 1.362137] scsi2 : pata_amd
[ 1.362621] scsi3 : pata_amd
[ 1.362921] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 1.362998] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 1.368001] I2O subsystem v1.325
[ 1.368077] i2o: max drivers = 8
[ 1.368591] I2O Configuration OSM v1.323
[ 1.368753] I2O Bus Adapter OSM v1.317
[ 1.368917] I2O Block Device OSM v1.325
[ 1.369448] I2O SCSI Peripheral OSM v1.316
[ 1.369614] I2O ProcFS OSM v1.316
[ 1.369799] Fusion MPT base driver 3.04.15
[ 1.369869] Copyright (c) 1999-2008 LSI Corporation
[ 1.369946] Fusion MPT SPI Host driver 3.04.15
[ 1.370139] Fusion MPT FC Host driver 3.04.15
[ 1.370345] Fusion MPT SAS Host driver 3.04.15
[ 1.370534] Fusion MPT misc device (ioctl) driver 3.04.15
[ 1.370828] mptctl: Registered with Fusion MPT base driver
[ 1.370902] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 1.370975] Fusion MPT LAN driver 3.04.15
[ 1.371345] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.371642] 116x: driver isp116x-hcd, 03 Nov 2005
[ 1.371809] driver isp1362-hcd, 2005-04-04
[ 1.371978] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.372105] ohci_hcd 0000:03:00.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 1.372218] ohci_hcd 0000:03:00.0: OHCI Host Controller
[ 1.372499] ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
[ 1.372663] ohci_hcd 0000:03:00.0: irq 19, io mem 0xe8200000
[ 1.425088] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.425164] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.425279] usb usb1: Product: OHCI Host Controller
[ 1.425349] usb usb1: Manufacturer: Linux 2.6.35.11-smp ohci_hcd
[ 1.425422] usb usb1: SerialNumber: 0000:03:00.0
[ 1.425844] hub 1-0:1.0: USB hub found
[ 1.425926] hub 1-0:1.0: 4 ports detected
[ 1.427119] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.427546] sl811: driver sl811-hcd, 19 May 2005
[ 1.427720] r8a66597_hcd: driver r8a66597_hcd, 2009-05-26
[ 1.428211] Initializing USB Mass Storage driver...
[ 1.428417] usbcore: registered new interface driver usb-storage
[ 1.428490] USB Mass Storage support registered.
[ 1.428658] usbcore: registered new interface driver ums-alauda
[ 1.428829] usbcore: registered new interface driver ums-cypress
[ 1.429008] usbcore: registered new interface driver ums-datafab
[ 1.429182] usbcore: registered new interface driver ums-freecom
[ 1.429367] usbcore: registered new interface driver ums-isd200
[ 1.429538] usbcore: registered new interface driver ums-jumpshot
[ 1.429708] usbcore: registered new interface driver ums-karma
[ 1.429875] usbcore: registered new interface driver ums-onetouch
[ 1.430058] usbcore: registered new interface driver ums-sddr09
[ 1.430226] usbcore: registered new interface driver ums-sddr55
[ 1.430407] usbcore: registered new interface driver ums-usbat
[ 1.430741] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.433307] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.433387] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.434022] mice: PS/2 mouse device common for all mice
[ 1.434208] md: linear personality registered for level -1
[ 1.434294] md: raid0 personality registered for level 0
[ 1.434365] md: raid1 personality registered for level 1
[ 1.434437] md: raid10 personality registered for level 10
[ 1.434508] md: raid6 personality registered for level 6
[ 1.434579] md: raid5 personality registered for level 5
[ 1.434649] md: raid4 personality registered for level 4
[ 1.434720] md: multipath personality registered for level -4
[ 1.435236] device-mapper: uevent: version 1.0.3
[ 1.435689] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 1.436095] cpuidle: using governor ladder
[ 1.436166] cpuidle: using governor menu
[ 1.436374] TCP cubic registered
[ 1.436443] Initializing XFRM netlink socket
[ 1.436531] NET: Registered protocol family 17
[ 1.436664] Using IPI No-Shortcut mode
[ 1.455007] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.536507] ata1.00: ATA-6: ST340810A, 3.39, max UDMA/100
[ 1.536580] ata1.00: 78165360 sectors, multi 16: LBA
[ 1.537136] ata1.01: ATA-6: ST3160023A, 8.01, max UDMA/100
[ 1.537209] ata1.01: 312581808 sectors, multi 16: LBA48
[ 1.559418] ata1.00: configured for UDMA/100
[ 1.565425] ata1.01: configured for UDMA/100
[ 1.565821] scsi 2:0:0:0: Direct-Access ATA ST340810A 3.39 PQ: 0 ANSI: 5
[ 1.566676] sd 2:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 1.566875] sd 2:0:0:0: [sda] Write Protect is off
[ 1.566948] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.566989] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.567691] scsi 2:0:1:0: Direct-Access ATA ST3160023A 8.01 PQ: 0 ANSI: 5
[ 1.568192] sda: sda1 sda2 sda3
[ 1.602752] sd 2:0:1:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.602834] sd 2:0:1:0: [sdb] Write Protect is off
[ 1.602840] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.602874] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.603127] sda4
[ 1.603766] sdb: sdb1 sdb2
[ 1.621363] sd 2:0:0:0: [sda] Attached SCSI disk
[ 1.622065] sd 2:0:1:0: [sdb] Attached SCSI disk
[ 1.757277] ata2.00: ATAPI: LITE-ON DVDRW LH-20A1H, LL0C, max UDMA/66
[ 1.757389] ata2.01: ATAPI: MATSHITA CD-RW CW-7586, 1.08, max MWDMA2
[ 1.757490] ata2.00: limited to UDMA/33 due to 40-wire cable
[ 1.779199] ata2.00: configured for UDMA/33
[ 1.801291] ata2.01: configured for MWDMA2
[ 1.803830] scsi 3:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1H LL0C PQ: 0 ANSI: 5
[ 1.809492] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.809605] Uniform CD-ROM driver Revision: 3.20
[ 1.810132] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 1.812240] scsi 3:0:1:0: CD-ROM MATSHITA CD-RW CW-7586 1.08 PQ: 0 ANSI: 5
[ 1.815522] sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
[ 1.815999] sr 3:0:1:0: Attached scsi CD-ROM sr1
[ 1.816404] registered taskstats version 1
[ 1.816914] md: Waiting for all devices to be available before autodetect
[ 1.816988] md: If you don't use raid, use raid=noautodetect
[ 1.817565] md: Autodetecting RAID arrays.
[ 1.817636] md: Scanned 0 and added 0 devices.
[ 1.817705] md: autorun ...
[ 1.817771] md: ... autorun DONE.
[ 1.844852] REISERFS (device sda4): found reiserfs format "3.6" with standard journal
[ 1.844981] REISERFS (device sda4): using ordered data mode
[ 1.857852] REISERFS (device sda4): journal params: device sda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 1.860813] REISERFS (device sda4): checking transaction log (sda4)
[ 1.882303] REISERFS (device sda4): Using r5 hash to sort names
[ 1.882441] VFS: Mounted root (reiserfs filesystem) readonly on device 8:4.
[ 1.882564] devtmpfs: mounted
[ 1.882692] Freeing unused kernel memory: 604k freed
[ 1.884105] Write protecting the kernel text: 9844k
[ 1.884264] Write protecting the kernel read-only data: 2516k
[ 3.595785] udev[1085]: starting version 165
[ 4.081211] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 4.081404] sd 2:0:1:0: Attached scsi generic sg1 type 0
[ 4.081534] sr 3:0:0:0: Attached scsi generic sg2 type 5
[ 4.081658] sr 3:0:1:0: Attached scsi generic sg3 type 5
[ 4.167844] shpchp 0000:00:01.0: HPC vendor_id 1022 device_id 700d ss_vid 0 ss_did 0
[ 4.167966] shpchp 0000:00:01.0: Cannot reserve MMIO region
[ 4.168061] shpchp 0000:00:10.0: HPC vendor_id 1022 device_id 7448 ss_vid 0 ss_did 0
[ 4.168166] shpchp 0000:00:10.0: Cannot reserve MMIO region
[ 4.168475] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 4.755831] 3c59x 0000:03:08.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 4.755955] 3c59x: Donald Becker and others.
[ 4.756039] 0000:03:08.0: 3Com PCI 3c905C Tornado at f869e400.
[ 5.049204] AMD768 RNG detected
[ 5.222363] cfg80211: Calling CRDA to update world regulatory domain
[ 5.602235] Linux agpgart interface v0.103
[ 5.723667] "amd76xrom" amd76xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug?
[ 5.747579] agpgart-amdk7 0000:00:00.0: AMD 760MP chipset
[ 5.767140] agpgart-amdk7 0000:00:00.0: AGP aperture is 64M @ 0xec000000
[ 6.015708] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 6.016246] ACPI: Power Button [PWRB]
[ 6.016541] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 6.016781] ACPI: Power Button [PWRF]
[ 6.016985] input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input3
[ 6.017184] ACPI: Sleep Button [SLPF]
[ 6.352765] ACPI: acpi_idle registered with cpuidle
[ 6.477116] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 6.477249] rtc0: alarms up to one month, y3k, 242 bytes nvram
[ 6.653728] CA0106 0000:03:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 6.653882] snd-ca0106: Model 1006 Rev 00000000 Serial 10061102
[ 6.832982] [drm] Initialized drm 1.1.0 20060810
[ 7.717906] BUG: unable to handle kernel paging request at f8c8aaa0
[ 7.718009] IP: [<c14d38cf>] memcpy+0x1f/0x40
[ 7.718009] *pde = 36b3f067 *pte = 00000000
[ 7.718009] Oops: 0002 [#1] SMP
[ 7.718009] last sysfs file: /sys/devices/pci0000:00/0000:00:07.1/host2/target2:0:0/2:0:0:0/block/sda/removable
[ 7.718009] Modules linked in: jedec_probe parport drm snd_ca0106 mac80211 snd_rawmidi snd_seq_device rtc_cmos rtc_core eeprom_93cx6 processor cfi_probe thermal container gen_probe thermal_sys cfi_util rtc_lib button snd_ac97_codec ac97_bus snd_pcm snd_timer amd_k7_agp amd76xrom(+) hwmon agpgart mtd snd soundcore cfg80211 i2c_algo_bit i2c_amd756 amd_rng rfkill snd_page_alloc i2c_core chipreg 3c59x map_funcs mii evdev psmouse shpchp sg serio_raw
[ 7.718009]
[ 7.718009] Pid: 1124, comm: modprobe Not tainted 2.6.35.11-smp #2 S2466 TIGER MPX/Unknown
[ 7.718009] EIP: 0060:[<c14d38cf>] EFLAGS: 00010212 CPU: 0
[ 7.718009] EIP is at memcpy+0x1f/0x40
[ 7.718009] EAX: f8c8aaa0 EBX: 00000020 ECX: 00000008 EDX: f6aaba48
[ 7.718009] ESI: f6aaba48 EDI: f8c8aaa0 EBP: f6aaba40 ESP: f6aaba34
[ 7.718009] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 7.718009] Process modprobe (pid: 1124, ti=f6aaa000 task=f6aa0cf0 task.ti=f6aaa000)
[ 7.718009] Stack:
[ 7.718009] 000000aa 000aaaa0 f8be0000 f6aaba74 f867f0f3 000000aa 000000aa 000000aa
[ 7.718009] <0> 000000aa 000000aa 000000aa 000000aa 000000aa 00000008 f6aabb84 f6aaba9c
[ 7.718009] <0> f6aabd90 f86a2aec 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa
[ 7.718009] Call Trace:
[ 7.718009] [<f867f0f3>] ? simple_map_write+0x83/0xa0 [map_funcs]
[ 7.718009] [<f86a2aec>] ? cfi_qry_mode_on+0xc7c/0x1130 [cfi_util]
[ 7.718009] [<f8d67eac>] ? jedec_probe_chip+0x71c/0x13a8 [jedec_probe]
[ 7.718009] [<f87061f6>] ? cfi_probe_chip+0x46/0x494 [cfi_probe]
[ 7.718009] [<f86ce1b2>] ? mtd_do_chip_probe+0xb2/0x398 [gen_probe]
[ 7.718009] [<c10254d0>] ? do_page_fault+0x0/0x370
[ 7.718009] [<f8706012>] ? cfi_probe+0x12/0x20 [cfi_probe]
[ 7.718009] [<f8697199>] ? do_map_probe+0x29/0x7b [chipreg]
[ 7.718009] [<f881a261>] ? init_amd76xrom+0x261/0x419 [amd76xrom]
[ 7.718009] [<c1001242>] ? do_one_initcall+0x32/0x190
[ 7.718009] [<f881a000>] ? init_amd76xrom+0x0/0x419 [amd76xrom]
[ 7.718009] [<c1074ba3>] ? sys_init_module+0x93/0x1d0
[ 7.718009] [<c10f20c2>] ? sys_write+0x42/0x70
[ 7.718009] [<c199ac6c>] ? syscall_call+0x7/0xb
[ 7.718009] Code: 8d 74 26 00 e8 63 fd ff ff eb e8 90 55 89 e5 83 ec 0c 89 1c 24 89 74 24 04 89 7c 24 08 0f 1f 44 00 00 89 cb 89 c7 c1 e9 02 89 d6 <f3> a5 89 d9 83 e1 03 74 02 f3 a4 8b 1c 24 8b 74 24 04 8b 7c 24
[ 7.718009] EIP: [<c14d38cf>] memcpy+0x1f/0x40 SS:ESP 0068:f6aaba34
[ 7.718009] CR2: 00000000f8c8aaa0
[ 7.718009] ---[ end trace 7d61458dad6b2dfe ]---
[ 7.744480] parport_pc 00:0b: reported by Plug and Play ACPI
[ 7.744688] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
[ 7.816274] ppdev: user-space parallel port driver
[ 7.858206] rtl8180 0000:03:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.033163] [drm] radeon defaulting to kernel modesetting.
[ 8.033250] [drm] radeon kernel modesetting enabled.
[ 8.033478] radeon 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.040981] [drm] initializing kernel modesetting (R200 0x1002:0x4242).
[ 8.041329] [drm] register mmio base: 0xE8020000
[ 8.041401] [drm] register mmio size: 131072
[ 8.041836] agpgart-amdk7 0000:00:00.0: AGP 2.0 bridge
[ 8.041928] agpgart-amdk7 0000:00:00.0: putting AGP V2 device into 4x mode
[ 8.042043] radeon 0000:01:05.0: putting AGP V2 device into 4x mode
[ 8.042150] radeon 0000:01:05.0: GTT: 64M 0xEC000000 - 0xEFFFFFFF
[ 8.042228] [drm] Generation 1 PCI interface in multifunction mode
[ 8.042301] [drm] Limiting VRAM to one aperture
[ 8.042376] radeon 0000:01:05.0: VRAM: 128M 0xF0000000 - 0xF7FFFFFF (64M used)
[ 8.042546] [drm] radeon: irq initialized.
[ 8.048780] [drm] Detected VRAM RAM=128M, BAR=128M
[ 8.048868] [drm] RAM width 128bits DDR
[ 8.049191] [TTM] Zone kernel: Available graphics memory: 430268 kiB.
[ 8.049268] [TTM] Zone highmem: Available graphics memory: 1286048 kiB.
[ 8.049342] [TTM] Initializing pool allocator.
[ 8.049464] [drm] radeon: 64M of VRAM memory ready
[ 8.049536] [drm] radeon: 64M of GTT memory ready.
[ 8.050824] [drm] Loading R200 Microcode
[ 8.054340] phy0: Selected rate control algorithm 'minstrel'
[ 8.054727] phy0: hwaddr 08:10:74:a6:8b:ad, RTL8185vD + rtl8225z2
[ 8.092368] [TTM] AGP Bind memory failed.
[ 8.092457] [TTM] Couldn't bind backend.
[ 8.092561] radeon 0000:01:05.0: object_init failed for (1048576, 0x00000002)
[ 8.092638] radeon 0000:01:05.0: (-22) ring create failed
[ 8.092711] radeon 0000:01:05.0: failled initializing CP (-22).
[ 8.092784] radeon 0000:01:05.0: Disabling GPU acceleration
[ 8.092860] [drm] radeon: cp finalized
[ 8.092960] [drm] radeon: cp finalized
[ 8.093109] [TTM] Finalizing pool allocator.
[ 8.094065] [TTM] Zone kernel: Used memory at exit: 0 kiB.
[ 8.094141] [TTM] Zone highmem: Used memory at exit: 0 kiB.
[ 8.094214] [drm] radeon: ttm finalized
[ 8.094290] [drm] Forcing AGP to PCI mode
[ 8.094722] [drm] Generation 1 PCI interface in multifunction mode
[ 8.094796] [drm] Limiting VRAM to one aperture
[ 8.094871] radeon 0000:01:05.0: VRAM: 128M 0xF0000000 - 0xF7FFFFFF (64M used)
[ 8.094976] radeon 0000:01:05.0: GTT: 512M 0xD0000000 - 0xEFFFFFFF
[ 8.095103] [drm] radeon: irq initialized.
[ 8.095183] [drm] Detected VRAM RAM=128M, BAR=128M
[ 8.095254] [drm] RAM width 128bits DDR
[ 8.095479] [TTM] Zone kernel: Available graphics memory: 430268 kiB.
[ 8.095554] [TTM] Zone highmem: Available graphics memory: 1286048 kiB.
[ 8.095628] [TTM] Initializing pool allocator.
[ 8.095742] [drm] radeon: 64M of VRAM memory ready
[ 8.095814] [drm] radeon: 512M of GTT memory ready.
[ 8.095897] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 8.104896] [drm] radeon: ring at 0x00000000D0000000
[ 8.105038] [drm] ring test succeeded in 7 usecs
[ 8.105283] [drm] radeon: ib pool ready.
[ 8.105546] [drm] ib test succeeded in 0 usecs
[ 8.105705] [drm] DFP table revision: 3
[ 8.106512] [drm] Radeon Display Connectors
[ 8.106590] [drm] Connector 0:
[ 8.106658] [drm] DVI-I
[ 8.106725] [drm] HPD1
[ 8.106793] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 8.106864] [drm] Encoders:
[ 8.106933] [drm] CRT1: INTERNAL_DAC1
[ 8.107020] [drm] DFP1: INTERNAL_TMDS1
[ 8.238330] [drm] fb mappable at 0xF0040000
[ 8.238402] [drm] vram apper at 0xF0000000
[ 8.238471] [drm] size 5242880
[ 8.238538] [drm] fb depth is 24
[ 8.238605] [drm] pitch is 5120
[ 8.311302] Console: switching to colour frame buffer device 160x64
[ 8.331774] fb0: radeondrmfb frame buffer device
[ 8.331885] drm: registered panic notifier
[ 8.331998] [drm] Initialized radeon 2.5.0 20080528 for 0000:01:05.0 on minor 0
[ 8.338722] [drm] initializing kernel modesetting (R200 0x1002:0x4243).
[ 8.339111] radeon 0000:01:05.1: Fatal error during GPU init
[ 8.339251] [drm] radeon: finishing device.
[ 8.339355] [TTM] Memory type 2 has not been initialized.
[ 8.339519] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 8.339701] IP: [<f905f797>] r100_cp_fini+0x57/0xb0 [radeon]
[ 8.339970] *pde = 00000000
[ 8.340049] Oops: 0002 [#2] SMP
[ 8.340083] last sysfs file: /sys/devices/virtual/vtconsole/vtcon1/uevent
[ 8.340083] Modules linked in: radeon(+) ttm rtl8180 ppdev drm_kms_helper parport_pc jedec_probe parport drm snd_ca0106 mac80211 snd_rawmidi snd_seq_device rtc_cmos rtc_core eeprom_93cx6 processor cfi_probe thermal container gen_probe thermal_sys cfi_util rtc_lib button snd_ac97_codec ac97_bus snd_pcm snd_timer amd_k7_agp amd76xrom(+) hwmon agpgart mtd snd soundcore cfg80211 i2c_algo_bit i2c_amd756 amd_rng rfkill snd_page_alloc i2c_core chipreg 3c59x map_funcs mii evdev psmouse shpchp sg serio_raw
[ 8.340083]
[ 8.340083] Pid: 1187, comm: modprobe Tainted: G D 2.6.35.11-smp #2 S2466 TIGER MPX/Unknown
[ 8.340083] EIP: 0060:[<f905f797>] EFLAGS: 00010287 CPU: 0
[ 8.340083] EIP is at r100_cp_fini+0x57/0xb0 [radeon]
[ 8.340083] EAX: 00000000 EBX: f709e000 ECX: ffff8000 EDX: f90c9120
[ 8.340083] ESI: 00000000 EDI: 00000e40 EBP: f6a0dda0 ESP: f6a0dd8c
[ 8.340083] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 8.340083] Process modprobe (pid: 1187, ti=f6a0c000 task=f6b8ab20 task.ti=f6a0c000)
[ 8.340083] Stack:
[ 8.340083] f8e1821c f6a0dda0 f709e000 f663f000 00800005 f6a0ddac f9065760 f709e000
[ 8.340083] <0> f6a0ddbc f902e293 f90b84bc f709e000 f6a0ddcc f902f3dc f663f000 f7125260
[ 8.340083] <0> f6a0ddfc f902f517 f90b86dc f90c0c70 f7125260 fffffff4 0000003f 00000001
[ 8.340083] Call Trace:
[ 8.340083] [<f9065760>] ? r100_fini+0x10/0x70 [radeon]
[ 8.340083] [<f902e293>] ? radeon_device_fini+0x33/0x80 [radeon]
[ 8.340083] [<f902f3dc>] ? radeon_driver_unload_kms+0x2c/0x50 [radeon]
[ 8.340083] [<f902f517>] ? radeon_driver_load_kms+0x117/0x1b0 [radeon]
[ 8.340083] [<f8d1f82c>] ? drm_get_dev+0x2ac/0x490 [drm]
[ 8.340083] [<f90a99f2>] ? radeon_pci_probe+0x12/0x14 [radeon]
[ 8.340083] [<c14e974e>] ? pci_device_probe+0x5e/0x80
[ 8.340083] [<c1561fdf>] ? driver_probe_device+0x7f/0x190
[ 8.340083] [<c14e914b>] ? pci_match_device+0xab/0xc0
[ 8.340083] [<c1562171>] ? __driver_attach+0x81/0x90
[ 8.340083] [<c1561199>] ? bus_for_each_dev+0x49/0x70
[ 8.340083] [<c1561d0e>] ? driver_attach+0x1e/0x20
[ 8.340083] [<c15620f0>] ? __driver_attach+0x0/0x90
[ 8.340083] [<c15618c2>] ? bus_add_driver+0xc2/0x2c0
[ 8.340083] [<c14e9690>] ? pci_device_remove+0x0/0x40
[ 8.340083] [<c15623a6>] ? driver_register+0x66/0x110
[ 8.340083] [<c14e9975>] ? __pci_register_driver+0x45/0xb0
[ 8.340083] [<f8d1a7c1>] ? drm_init+0xf1/0x100 [drm]
[ 8.340083] [<f91a10b7>] ? radeon_init+0xb7/0xb9 [radeon]
[ 8.340083] [<c1001242>] ? do_one_initcall+0x32/0x190
[ 8.340083] [<f91a1000>] ? radeon_init+0x0/0xb9 [radeon]
[ 8.340083] [<c1074ba3>] ? sys_init_module+0x93/0x1d0
[ 8.340083] [<c10f20c2>] ? sys_write+0x42/0x70
[ 8.340083] [<c199ac6c>] ? syscall_call+0x7/0xb
[ 8.340083] Code: a9 00 00 01 00 74 36 b8 c7 10 00 00 83 c6 01 e8 a0 37 47 c8 3b 73 6c 73 4b 81 bb 90 00 00 00 40 0e 00 00 77 cf 8b 83 94 00 00 00 <89> 38 8b 83 94 00 00 00 8b 40 04 a9 00 00 01 00 75 ca 89 d8 e8
[ 8.340083] EIP: [<f905f797>] r100_cp_fini+0x57/0xb0 [radeon] SS:ESP 0068:f6a0dd8c
[ 8.340083] CR2: 0000000000000000
[ 8.457876] ---[ end trace 7d61458dad6b2dff ]---
[ 125.620673] lp0: using parport0 (interrupt-driven).
[ 125.628435] lp0: console ready
[ 427.840486] REISERFS (device sdb2): found reiserfs format "3.6" with standard journal
[ 427.840535] REISERFS (device sdb2): using ordered data mode
[ 427.850348] REISERFS (device sdb2): journal params: device sdb2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 427.853365] REISERFS (device sdb2): checking transaction log (sdb2)
[ 427.902591] REISERFS (device sdb2): Using r5 hash to sort names
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.35.9 bug shown in dmesg (fwd)
2011-02-14 2:50 ` Russell Whitaker
@ 2011-02-14 17:31 ` Stanislaw Gruszka
0 siblings, 0 replies; 8+ messages in thread
From: Stanislaw Gruszka @ 2011-02-14 17:31 UTC (permalink / raw)
To: Russell Whitaker; +Cc: linux-ide, dri-devel
On Sun, Feb 13, 2011 at 06:50:02PM -0800, Russell Whitaker wrote:
> Ok, you are right. Somewhat started over and now got a saved "dmesg"
> with the newer kernel. Copy of dmesg attached.
>
> Background info:
> motherboard: Tyan Tiger MPX, 2 AMD cpu's
> software: Slackware-current 2/14/2011, "A" series
> Selected Huge-SMP kernel
>
There are mtd and radeon oopses in dmesg. There is no indication
that could be caused by ATA. MTD is already fixed in linux-next,
regarding radeon CCing on dri-devel mailing list.
Stanislaw
> [ 0.139723] pci 0000:03:08.0: reg 30: [mem 0x00000000-0x0001ffff pref]
> [ 0.139745] pci 0000:03:08.0: supports D1 D2
> [ 0.139749] pci 0000:03:08.0: PME# supported from D0 D1 D2 D3hot D3cold
> [ 0.139755] pci 0000:03:08.0: PME# disabled
> [ 0.139793] pci 0000:00:10.0: PCI bridge to [bus 03-03]
> [ 0.139867] pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
> [ 0.139873] pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
> [ 0.139879] pci 0000:00:10.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
> [ 0.139892] pci_bus 0000:00: on NUMA node 0
> [ 0.139899] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> [ 0.140058] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
> [ 0.140136] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT]
> [ 0.144214] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
> [ 0.145407] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *0, disabled.
> [ 0.145936] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
> [ 0.146434] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
> [ 0.146781] HEST: Table is not found!
> [ 0.147132] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
> [ 0.147136] vgaarb: loaded
> [ 0.147379] SCSI subsystem initialized
> [ 0.148118] libata version 3.00 loaded.
> [ 0.148118] usbcore: registered new interface driver usbfs
> [ 0.148139] usbcore: registered new interface driver hub
> [ 0.149059] usbcore: registered new device driver usb
> [ 0.166966] raid6: int32x1 707 MB/s
> [ 0.184004] raid6: int32x2 628 MB/s
> [ 0.201050] raid6: int32x4 511 MB/s
> [ 0.218015] raid6: int32x8 496 MB/s
> [ 0.234951] raid6: mmxx1 1320 MB/s
> [ 0.251958] raid6: mmxx2 2156 MB/s
> [ 0.269013] raid6: sse1x1 460 MB/s
> [ 0.285969] raid6: sse1x2 917 MB/s
> [ 0.286002] raid6: using algorithm sse1x2 (917 MB/s)
> [ 0.286091] PCI: Using ACPI for IRQ routing
> [ 0.286168] PCI: pci_cache_line_size set to 32 bytes
> [ 0.286243] reserve RAM buffer: 000000000009f800 - 000000000009ffff
> [ 0.286250] reserve RAM buffer: 000000009fef0000 - 000000009fffffff
> [ 0.286255] reserve RAM buffer: 000000009ff80000 - 000000009fffffff
> [ 0.293067] pnp: PnP ACPI init
> [ 0.293192] ACPI: bus type pnp registered
> [ 0.299162] pnp: PnP ACPI: found 13 devices
> [ 0.299162] ACPI: ACPI bus type pnp unregistered
> [ 0.299185] system 00:00: [mem 0xfffc0000-0xffffffff] has been reserved
> [ 0.299261] system 00:00: [mem 0xffc00000-0xfff7ffff] has been reserved
> [ 0.299336] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
> [ 0.299411] system 00:00: [mem 0x00100000-0x9fffffff] could not be reserved
> [ 0.299485] system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
> [ 0.299568] system 00:06: [io 0x04d0-0x04d1] has been reserved
> [ 0.343429] Switching to clocksource acpi_pm
> [ 0.343612] pci 0000:00:10.0: BAR 9: assigned [mem 0xa0000000-0xa00fffff pref]
> [ 0.343721] pci 0000:01:05.0: BAR 6: assigned [mem 0xe8040000-0xe805ffff pref]
> [ 0.343828] pci 0000:01:05.1: PCI bridge to [bus 02-02]
> [ 0.343900] pci 0000:01:05.1: bridge window [io disabled]
> [ 0.343978] pci 0000:01:05.1: bridge window [mem 0xe8100000-0xe81fffff]
> [ 0.343999] pci 0000:01:05.1: bridge window [mem pref disabled]
> [ 0.343999] pci 0000:00:01.0: PCI bridge to [bus 01-02]
> [ 0.343999] pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
> [ 0.343999] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe81fffff]
> [ 0.343999] pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf7ffffff pref]
> [ 0.343999] pci 0000:03:08.0: BAR 6: assigned [mem 0xa0000000-0xa001ffff pref]
> [ 0.344051] pci 0000:00:10.0: PCI bridge to [bus 03-03]
> [ 0.344123] pci 0000:00:10.0: bridge window [io 0x3000-0x3fff]
> [ 0.344198] pci 0000:00:10.0: bridge window [mem 0xe8200000-0xe82fffff]
> [ 0.344286] pci 0000:00:10.0: bridge window [mem 0xa0000000-0xa00fffff pref]
> [ 0.344422] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
> [ 0.344426] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
> [ 0.344431] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
> [ 0.344435] pci_bus 0000:01: resource 1 [mem 0xe8000000-0xe81fffff]
> [ 0.344439] pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf7ffffff pref]
> [ 0.344444] pci_bus 0000:02: resource 1 [mem 0xe8100000-0xe81fffff]
> [ 0.344448] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
> [ 0.344452] pci_bus 0000:03: resource 1 [mem 0xe8200000-0xe82fffff]
> [ 0.344456] pci_bus 0000:03: resource 2 [mem 0xa0000000-0xa00fffff pref]
> [ 0.344538] NET: Registered protocol family 2
> [ 0.344696] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
> [ 0.345309] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
> [ 0.348005] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
> [ 0.349385] TCP: Hash tables configured (established 131072 bind 65536)
> [ 0.349464] TCP reno registered
> [ 0.349540] UDP hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.349650] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.349962] NET: Registered protocol family 1
> [ 0.350235] RPC: Registered udp transport module.
> [ 0.350318] RPC: Registered tcp transport module.
> [ 0.350388] RPC: Registered tcp NFSv4.1 backchannel transport module.
> [ 0.350479] pci 0000:00:00.0: BIOS failed to enable PCI standards compliance; fixing this error
> [ 0.350613] pci 0000:01:05.0: Boot video device
> [ 0.350671] PCI: CLS 64 bytes, default 32
> [ 0.353746] audit: initializing netlink socket (disabled)
> [ 0.353850] type=2000 audit(1297557217.353:1): initialized
> [ 0.354320] highmem bounce pool size: 64 pages
> [ 0.361087] VFS: Disk quotas dquot_6.5.2
> [ 0.361328] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> [ 0.362055] DLM (built Feb 7 2011 23:48:44) installed
> [ 0.364709] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> [ 0.365518] NTFS driver 2.1.29 [Flags: R/W].
> [ 0.365880] ROMFS MTD (C) 2007 Red Hat, Inc.
> [ 0.366491] JFS: nTxBlock = 8192, nTxLock = 65536
> [ 0.376470] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
> [ 0.378105] SGI XFS Quota Management subsystem
> [ 0.378185] OCFS2 1.5.0
> [ 0.378740] ocfs2: Registered cluster interface o2cb
> [ 0.379021] ocfs2: Registered cluster interface user
> [ 0.379094] OCFS2 DLMFS 1.5.0
> [ 0.379391] OCFS2 User DLM kernel interface loaded
> [ 0.379464] OCFS2 Node Manager 1.5.0
> [ 0.379841] OCFS2 DLM 1.5.0
> [ 0.380557] Btrfs loaded
> [ 0.381869] Slow work thread pool: Starting up
> [ 0.382054] Slow work thread pool: Ready
> [ 0.382138] GFS2 (built Feb 7 2011 23:49:10) installed
> [ 0.382233] msgmni has been set to 1679
> [ 0.382724] alg: No test for cipher_null (cipher_null-generic)
> [ 0.382884] alg: No test for ecb(cipher_null) (ecb-cipher_null)
> [ 0.383077] alg: No test for digest_null (digest_null-generic)
> [ 0.383216] alg: No test for compress_null (compress_null-generic)
> [ 0.385396] alg: No test for fcrypt (fcrypt-generic)
> [ 0.389574] alg: No test for stdrng (krng)
> [ 0.389668] async_tx: api initialized (async)
> [ 0.390025] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
> [ 0.390134] io scheduler noop registered
> [ 0.390203] io scheduler deadline registered
> [ 0.390360] io scheduler cfq registered (default)
> [ 0.390976] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> [ 0.391787] ERST: Table is not found!
> [ 0.391871] isapnp: Scanning for PnP cards...
> [ 0.748787] isapnp: No Plug & Play device found
> [ 0.757359] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> [ 1.002192] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> [ 1.246191] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> [ 1.247234] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> [ 1.247674] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> [ 1.248513] Floppy drive(s): fd0 is 1.44M
> [ 1.262829] FDC 0 is a post-1991 82077
> [ 1.268840] brd: module loaded
> [ 1.271293] loop: module loaded
> [ 1.271365] Compaq SMART2 Driver (v 2.6.0)
> [ 1.271671] HP CISS Driver (v 3.6.20)
> [ 1.273808] Loading iSCSI transport class v2.0-870.
> [ 1.275357] fnic: Cisco FCoE HBA Driver, ver 1.4.0.145
> [ 1.279698] Adaptec aacraid driver 1.1-5[26400]-ms
> [ 1.280141] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
> [ 1.280789] scsi: <fdomain> Detection failed (no card)
> [ 1.280883] sym53c416.c: Version 1.0.0-ac
> [ 1.280978] qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options
> [ 1.281192] QLogic Fibre Channel HBA Driver: 8.03.02-k2
> [ 1.281586] iscsi: registered transport (qla4xxx)
> [ 1.281763] QLogic iSCSI HBA Driver
> [ 1.281832] Emulex LightPulse Fibre Channel SCSI driver 8.3.12
> [ 1.281904] Copyright(c) 2004-2009 Emulex. All rights reserved.
> [ 1.282109] Brocade BFA FC/FCOE SCSI driver - version: 2.1.2.1
> [ 1.304056] Failed initialization of WD-7000 SCSI card!
> [ 1.355584] DC390: clustering now enabled by default. If you get problems load
> [ 1.355690] with "disable_clustering=1" and report to maintainers
> [ 1.355997] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
> [ 1.356318] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
> [ 1.356498] megasas: 00.00.04.17.1-rc1 Thu. Oct. 29, 11:41:51 PST 2009
> [ 1.356688] mpt2sas version 05.100.00.02 loaded
> [ 1.357115] GDT-HA: Storage RAID Controller Driver. Version: 3.05
> [ 1.357492] 3ware Storage Controller device driver for Linux v1.26.02.003.
> [ 1.357665] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014.
> [ 1.357884] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000.
> [ 1.358101] ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
> [ 1.358325] RocketRAID 3xxx/4xxx Controller driver v1.6 (090910)
> [ 1.358500] stex: Promise SuperTrak EX Driver version: 4.6.0000.4
> [ 1.359002] st: Version 20081215, fixed bufsize 32768, s/g segs 256
> [ 1.361769] pata_amd 0000:00:07.1: version 0.4.1
> [ 1.361889] pata_amd 0000:00:07.1: setting latency timer to 64
> [ 1.362137] scsi2 : pata_amd
> [ 1.362621] scsi3 : pata_amd
> [ 1.362921] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
> [ 1.362998] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
> [ 1.368001] I2O subsystem v1.325
> [ 1.368077] i2o: max drivers = 8
> [ 1.368591] I2O Configuration OSM v1.323
> [ 1.368753] I2O Bus Adapter OSM v1.317
> [ 1.368917] I2O Block Device OSM v1.325
> [ 1.369448] I2O SCSI Peripheral OSM v1.316
> [ 1.369614] I2O ProcFS OSM v1.316
> [ 1.369799] Fusion MPT base driver 3.04.15
> [ 1.369869] Copyright (c) 1999-2008 LSI Corporation
> [ 1.369946] Fusion MPT SPI Host driver 3.04.15
> [ 1.370139] Fusion MPT FC Host driver 3.04.15
> [ 1.370345] Fusion MPT SAS Host driver 3.04.15
> [ 1.370534] Fusion MPT misc device (ioctl) driver 3.04.15
> [ 1.370828] mptctl: Registered with Fusion MPT base driver
> [ 1.370902] mptctl: /dev/mptctl @ (major,minor=10,220)
> [ 1.370975] Fusion MPT LAN driver 3.04.15
> [ 1.371345] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 1.371642] 116x: driver isp116x-hcd, 03 Nov 2005
> [ 1.371809] driver isp1362-hcd, 2005-04-04
> [ 1.371978] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> [ 1.372105] ohci_hcd 0000:03:00.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
> [ 1.372218] ohci_hcd 0000:03:00.0: OHCI Host Controller
> [ 1.372499] ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
> [ 1.372663] ohci_hcd 0000:03:00.0: irq 19, io mem 0xe8200000
> [ 1.425088] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
> [ 1.425164] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 1.425279] usb usb1: Product: OHCI Host Controller
> [ 1.425349] usb usb1: Manufacturer: Linux 2.6.35.11-smp ohci_hcd
> [ 1.425422] usb usb1: SerialNumber: 0000:03:00.0
> [ 1.425844] hub 1-0:1.0: USB hub found
> [ 1.425926] hub 1-0:1.0: 4 ports detected
> [ 1.427119] uhci_hcd: USB Universal Host Controller Interface driver
> [ 1.427546] sl811: driver sl811-hcd, 19 May 2005
> [ 1.427720] r8a66597_hcd: driver r8a66597_hcd, 2009-05-26
> [ 1.428211] Initializing USB Mass Storage driver...
> [ 1.428417] usbcore: registered new interface driver usb-storage
> [ 1.428490] USB Mass Storage support registered.
> [ 1.428658] usbcore: registered new interface driver ums-alauda
> [ 1.428829] usbcore: registered new interface driver ums-cypress
> [ 1.429008] usbcore: registered new interface driver ums-datafab
> [ 1.429182] usbcore: registered new interface driver ums-freecom
> [ 1.429367] usbcore: registered new interface driver ums-isd200
> [ 1.429538] usbcore: registered new interface driver ums-jumpshot
> [ 1.429708] usbcore: registered new interface driver ums-karma
> [ 1.429875] usbcore: registered new interface driver ums-onetouch
> [ 1.430058] usbcore: registered new interface driver ums-sddr09
> [ 1.430226] usbcore: registered new interface driver ums-sddr55
> [ 1.430407] usbcore: registered new interface driver ums-usbat
> [ 1.430741] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
> [ 1.433307] serio: i8042 KBD port at 0x60,0x64 irq 1
> [ 1.433387] serio: i8042 AUX port at 0x60,0x64 irq 12
> [ 1.434022] mice: PS/2 mouse device common for all mice
> [ 1.434208] md: linear personality registered for level -1
> [ 1.434294] md: raid0 personality registered for level 0
> [ 1.434365] md: raid1 personality registered for level 1
> [ 1.434437] md: raid10 personality registered for level 10
> [ 1.434508] md: raid6 personality registered for level 6
> [ 1.434579] md: raid5 personality registered for level 5
> [ 1.434649] md: raid4 personality registered for level 4
> [ 1.434720] md: multipath personality registered for level -4
> [ 1.435236] device-mapper: uevent: version 1.0.3
> [ 1.435689] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
> [ 1.436095] cpuidle: using governor ladder
> [ 1.436166] cpuidle: using governor menu
> [ 1.436374] TCP cubic registered
> [ 1.436443] Initializing XFRM netlink socket
> [ 1.436531] NET: Registered protocol family 17
> [ 1.436664] Using IPI No-Shortcut mode
> [ 1.455007] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
> [ 1.536507] ata1.00: ATA-6: ST340810A, 3.39, max UDMA/100
> [ 1.536580] ata1.00: 78165360 sectors, multi 16: LBA
> [ 1.537136] ata1.01: ATA-6: ST3160023A, 8.01, max UDMA/100
> [ 1.537209] ata1.01: 312581808 sectors, multi 16: LBA48
> [ 1.559418] ata1.00: configured for UDMA/100
> [ 1.565425] ata1.01: configured for UDMA/100
> [ 1.565821] scsi 2:0:0:0: Direct-Access ATA ST340810A 3.39 PQ: 0 ANSI: 5
> [ 1.566676] sd 2:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
> [ 1.566875] sd 2:0:0:0: [sda] Write Protect is off
> [ 1.566948] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 1.566989] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 1.567691] scsi 2:0:1:0: Direct-Access ATA ST3160023A 8.01 PQ: 0 ANSI: 5
> [ 1.568192] sda: sda1 sda2 sda3
> [ 1.602752] sd 2:0:1:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
> [ 1.602834] sd 2:0:1:0: [sdb] Write Protect is off
> [ 1.602840] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
> [ 1.602874] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 1.603127] sda4
> [ 1.603766] sdb: sdb1 sdb2
> [ 1.621363] sd 2:0:0:0: [sda] Attached SCSI disk
> [ 1.622065] sd 2:0:1:0: [sdb] Attached SCSI disk
> [ 1.757277] ata2.00: ATAPI: LITE-ON DVDRW LH-20A1H, LL0C, max UDMA/66
> [ 1.757389] ata2.01: ATAPI: MATSHITA CD-RW CW-7586, 1.08, max MWDMA2
> [ 1.757490] ata2.00: limited to UDMA/33 due to 40-wire cable
> [ 1.779199] ata2.00: configured for UDMA/33
> [ 1.801291] ata2.01: configured for MWDMA2
> [ 1.803830] scsi 3:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1H LL0C PQ: 0 ANSI: 5
> [ 1.809492] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
> [ 1.809605] Uniform CD-ROM driver Revision: 3.20
> [ 1.810132] sr 3:0:0:0: Attached scsi CD-ROM sr0
> [ 1.812240] scsi 3:0:1:0: CD-ROM MATSHITA CD-RW CW-7586 1.08 PQ: 0 ANSI: 5
> [ 1.815522] sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
> [ 1.815999] sr 3:0:1:0: Attached scsi CD-ROM sr1
> [ 1.816404] registered taskstats version 1
> [ 1.816914] md: Waiting for all devices to be available before autodetect
> [ 1.816988] md: If you don't use raid, use raid=noautodetect
> [ 1.817565] md: Autodetecting RAID arrays.
> [ 1.817636] md: Scanned 0 and added 0 devices.
> [ 1.817705] md: autorun ...
> [ 1.817771] md: ... autorun DONE.
> [ 1.844852] REISERFS (device sda4): found reiserfs format "3.6" with standard journal
> [ 1.844981] REISERFS (device sda4): using ordered data mode
> [ 1.857852] REISERFS (device sda4): journal params: device sda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
> [ 1.860813] REISERFS (device sda4): checking transaction log (sda4)
> [ 1.882303] REISERFS (device sda4): Using r5 hash to sort names
> [ 1.882441] VFS: Mounted root (reiserfs filesystem) readonly on device 8:4.
> [ 1.882564] devtmpfs: mounted
> [ 1.882692] Freeing unused kernel memory: 604k freed
> [ 1.884105] Write protecting the kernel text: 9844k
> [ 1.884264] Write protecting the kernel read-only data: 2516k
> [ 3.595785] udev[1085]: starting version 165
> [ 4.081211] sd 2:0:0:0: Attached scsi generic sg0 type 0
> [ 4.081404] sd 2:0:1:0: Attached scsi generic sg1 type 0
> [ 4.081534] sr 3:0:0:0: Attached scsi generic sg2 type 5
> [ 4.081658] sr 3:0:1:0: Attached scsi generic sg3 type 5
> [ 4.167844] shpchp 0000:00:01.0: HPC vendor_id 1022 device_id 700d ss_vid 0 ss_did 0
> [ 4.167966] shpchp 0000:00:01.0: Cannot reserve MMIO region
> [ 4.168061] shpchp 0000:00:10.0: HPC vendor_id 1022 device_id 7448 ss_vid 0 ss_did 0
> [ 4.168166] shpchp 0000:00:10.0: Cannot reserve MMIO region
> [ 4.168475] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
> [ 4.755831] 3c59x 0000:03:08.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
> [ 4.755955] 3c59x: Donald Becker and others.
> [ 4.756039] 0000:03:08.0: 3Com PCI 3c905C Tornado at f869e400.
> [ 5.049204] AMD768 RNG detected
> [ 5.222363] cfg80211: Calling CRDA to update world regulatory domain
> [ 5.602235] Linux agpgart interface v0.103
> [ 5.723667] "amd76xrom" amd76xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug?
> [ 5.747579] agpgart-amdk7 0000:00:00.0: AMD 760MP chipset
> [ 5.767140] agpgart-amdk7 0000:00:00.0: AGP aperture is 64M @ 0xec000000
> [ 6.015708] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
> [ 6.016246] ACPI: Power Button [PWRB]
> [ 6.016541] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
> [ 6.016781] ACPI: Power Button [PWRF]
> [ 6.016985] input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input3
> [ 6.017184] ACPI: Sleep Button [SLPF]
> [ 6.352765] ACPI: acpi_idle registered with cpuidle
> [ 6.477116] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
> [ 6.477249] rtc0: alarms up to one month, y3k, 242 bytes nvram
> [ 6.653728] CA0106 0000:03:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
> [ 6.653882] snd-ca0106: Model 1006 Rev 00000000 Serial 10061102
> [ 6.832982] [drm] Initialized drm 1.1.0 20060810
> [ 7.717906] BUG: unable to handle kernel paging request at f8c8aaa0
> [ 7.718009] IP: [<c14d38cf>] memcpy+0x1f/0x40
> [ 7.718009] *pde = 36b3f067 *pte = 00000000
> [ 7.718009] Oops: 0002 [#1] SMP
> [ 7.718009] last sysfs file: /sys/devices/pci0000:00/0000:00:07.1/host2/target2:0:0/2:0:0:0/block/sda/removable
> [ 7.718009] Modules linked in: jedec_probe parport drm snd_ca0106 mac80211 snd_rawmidi snd_seq_device rtc_cmos rtc_core eeprom_93cx6 processor cfi_probe thermal container gen_probe thermal_sys cfi_util rtc_lib button snd_ac97_codec ac97_bus snd_pcm snd_timer amd_k7_agp amd76xrom(+) hwmon agpgart mtd snd soundcore cfg80211 i2c_algo_bit i2c_amd756 amd_rng rfkill snd_page_alloc i2c_core chipreg 3c59x map_funcs mii evdev psmouse shpchp sg serio_raw
> [ 7.718009]
> [ 7.718009] Pid: 1124, comm: modprobe Not tainted 2.6.35.11-smp #2 S2466 TIGER MPX/Unknown
> [ 7.718009] EIP: 0060:[<c14d38cf>] EFLAGS: 00010212 CPU: 0
> [ 7.718009] EIP is at memcpy+0x1f/0x40
> [ 7.718009] EAX: f8c8aaa0 EBX: 00000020 ECX: 00000008 EDX: f6aaba48
> [ 7.718009] ESI: f6aaba48 EDI: f8c8aaa0 EBP: f6aaba40 ESP: f6aaba34
> [ 7.718009] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
> [ 7.718009] Process modprobe (pid: 1124, ti=f6aaa000 task=f6aa0cf0 task.ti=f6aaa000)
> [ 7.718009] Stack:
> [ 7.718009] 000000aa 000aaaa0 f8be0000 f6aaba74 f867f0f3 000000aa 000000aa 000000aa
> [ 7.718009] <0> 000000aa 000000aa 000000aa 000000aa 000000aa 00000008 f6aabb84 f6aaba9c
> [ 7.718009] <0> f6aabd90 f86a2aec 000000aa 000000aa 000000aa 000000aa 000000aa 000000aa
> [ 7.718009] Call Trace:
> [ 7.718009] [<f867f0f3>] ? simple_map_write+0x83/0xa0 [map_funcs]
> [ 7.718009] [<f86a2aec>] ? cfi_qry_mode_on+0xc7c/0x1130 [cfi_util]
> [ 7.718009] [<f8d67eac>] ? jedec_probe_chip+0x71c/0x13a8 [jedec_probe]
> [ 7.718009] [<f87061f6>] ? cfi_probe_chip+0x46/0x494 [cfi_probe]
> [ 7.718009] [<f86ce1b2>] ? mtd_do_chip_probe+0xb2/0x398 [gen_probe]
> [ 7.718009] [<c10254d0>] ? do_page_fault+0x0/0x370
> [ 7.718009] [<f8706012>] ? cfi_probe+0x12/0x20 [cfi_probe]
> [ 7.718009] [<f8697199>] ? do_map_probe+0x29/0x7b [chipreg]
> [ 7.718009] [<f881a261>] ? init_amd76xrom+0x261/0x419 [amd76xrom]
> [ 7.718009] [<c1001242>] ? do_one_initcall+0x32/0x190
> [ 7.718009] [<f881a000>] ? init_amd76xrom+0x0/0x419 [amd76xrom]
> [ 7.718009] [<c1074ba3>] ? sys_init_module+0x93/0x1d0
> [ 7.718009] [<c10f20c2>] ? sys_write+0x42/0x70
> [ 7.718009] [<c199ac6c>] ? syscall_call+0x7/0xb
> [ 7.718009] Code: 8d 74 26 00 e8 63 fd ff ff eb e8 90 55 89 e5 83 ec 0c 89 1c 24 89 74 24 04 89 7c 24 08 0f 1f 44 00 00 89 cb 89 c7 c1 e9 02 89 d6 <f3> a5 89 d9 83 e1 03 74 02 f3 a4 8b 1c 24 8b 74 24 04 8b 7c 24
> [ 7.718009] EIP: [<c14d38cf>] memcpy+0x1f/0x40 SS:ESP 0068:f6aaba34
> [ 7.718009] CR2: 00000000f8c8aaa0
> [ 7.718009] ---[ end trace 7d61458dad6b2dfe ]---
> [ 7.744480] parport_pc 00:0b: reported by Plug and Play ACPI
> [ 7.744688] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
> [ 7.816274] ppdev: user-space parallel port driver
> [ 7.858206] rtl8180 0000:03:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
> [ 8.033163] [drm] radeon defaulting to kernel modesetting.
> [ 8.033250] [drm] radeon kernel modesetting enabled.
> [ 8.033478] radeon 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
> [ 8.040981] [drm] initializing kernel modesetting (R200 0x1002:0x4242).
> [ 8.041329] [drm] register mmio base: 0xE8020000
> [ 8.041401] [drm] register mmio size: 131072
> [ 8.041836] agpgart-amdk7 0000:00:00.0: AGP 2.0 bridge
> [ 8.041928] agpgart-amdk7 0000:00:00.0: putting AGP V2 device into 4x mode
> [ 8.042043] radeon 0000:01:05.0: putting AGP V2 device into 4x mode
> [ 8.042150] radeon 0000:01:05.0: GTT: 64M 0xEC000000 - 0xEFFFFFFF
> [ 8.042228] [drm] Generation 1 PCI interface in multifunction mode
> [ 8.042301] [drm] Limiting VRAM to one aperture
> [ 8.042376] radeon 0000:01:05.0: VRAM: 128M 0xF0000000 - 0xF7FFFFFF (64M used)
> [ 8.042546] [drm] radeon: irq initialized.
> [ 8.048780] [drm] Detected VRAM RAM=128M, BAR=128M
> [ 8.048868] [drm] RAM width 128bits DDR
> [ 8.049191] [TTM] Zone kernel: Available graphics memory: 430268 kiB.
> [ 8.049268] [TTM] Zone highmem: Available graphics memory: 1286048 kiB.
> [ 8.049342] [TTM] Initializing pool allocator.
> [ 8.049464] [drm] radeon: 64M of VRAM memory ready
> [ 8.049536] [drm] radeon: 64M of GTT memory ready.
> [ 8.050824] [drm] Loading R200 Microcode
> [ 8.054340] phy0: Selected rate control algorithm 'minstrel'
> [ 8.054727] phy0: hwaddr 08:10:74:a6:8b:ad, RTL8185vD + rtl8225z2
> [ 8.092368] [TTM] AGP Bind memory failed.
> [ 8.092457] [TTM] Couldn't bind backend.
> [ 8.092561] radeon 0000:01:05.0: object_init failed for (1048576, 0x00000002)
> [ 8.092638] radeon 0000:01:05.0: (-22) ring create failed
> [ 8.092711] radeon 0000:01:05.0: failled initializing CP (-22).
> [ 8.092784] radeon 0000:01:05.0: Disabling GPU acceleration
> [ 8.092860] [drm] radeon: cp finalized
> [ 8.092960] [drm] radeon: cp finalized
> [ 8.093109] [TTM] Finalizing pool allocator.
> [ 8.094065] [TTM] Zone kernel: Used memory at exit: 0 kiB.
> [ 8.094141] [TTM] Zone highmem: Used memory at exit: 0 kiB.
> [ 8.094214] [drm] radeon: ttm finalized
> [ 8.094290] [drm] Forcing AGP to PCI mode
> [ 8.094722] [drm] Generation 1 PCI interface in multifunction mode
> [ 8.094796] [drm] Limiting VRAM to one aperture
> [ 8.094871] radeon 0000:01:05.0: VRAM: 128M 0xF0000000 - 0xF7FFFFFF (64M used)
> [ 8.094976] radeon 0000:01:05.0: GTT: 512M 0xD0000000 - 0xEFFFFFFF
> [ 8.095103] [drm] radeon: irq initialized.
> [ 8.095183] [drm] Detected VRAM RAM=128M, BAR=128M
> [ 8.095254] [drm] RAM width 128bits DDR
> [ 8.095479] [TTM] Zone kernel: Available graphics memory: 430268 kiB.
> [ 8.095554] [TTM] Zone highmem: Available graphics memory: 1286048 kiB.
> [ 8.095628] [TTM] Initializing pool allocator.
> [ 8.095742] [drm] radeon: 64M of VRAM memory ready
> [ 8.095814] [drm] radeon: 512M of GTT memory ready.
> [ 8.095897] [drm] GART: num cpu pages 131072, num gpu pages 131072
> [ 8.104896] [drm] radeon: ring at 0x00000000D0000000
> [ 8.105038] [drm] ring test succeeded in 7 usecs
> [ 8.105283] [drm] radeon: ib pool ready.
> [ 8.105546] [drm] ib test succeeded in 0 usecs
> [ 8.105705] [drm] DFP table revision: 3
> [ 8.106512] [drm] Radeon Display Connectors
> [ 8.106590] [drm] Connector 0:
> [ 8.106658] [drm] DVI-I
> [ 8.106725] [drm] HPD1
> [ 8.106793] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
> [ 8.106864] [drm] Encoders:
> [ 8.106933] [drm] CRT1: INTERNAL_DAC1
> [ 8.107020] [drm] DFP1: INTERNAL_TMDS1
> [ 8.238330] [drm] fb mappable at 0xF0040000
> [ 8.238402] [drm] vram apper at 0xF0000000
> [ 8.238471] [drm] size 5242880
> [ 8.238538] [drm] fb depth is 24
> [ 8.238605] [drm] pitch is 5120
> [ 8.311302] Console: switching to colour frame buffer device 160x64
> [ 8.331774] fb0: radeondrmfb frame buffer device
> [ 8.331885] drm: registered panic notifier
> [ 8.331998] [drm] Initialized radeon 2.5.0 20080528 for 0000:01:05.0 on minor 0
> [ 8.338722] [drm] initializing kernel modesetting (R200 0x1002:0x4243).
> [ 8.339111] radeon 0000:01:05.1: Fatal error during GPU init
> [ 8.339251] [drm] radeon: finishing device.
> [ 8.339355] [TTM] Memory type 2 has not been initialized.
> [ 8.339519] BUG: unable to handle kernel NULL pointer dereference at (null)
> [ 8.339701] IP: [<f905f797>] r100_cp_fini+0x57/0xb0 [radeon]
> [ 8.339970] *pde = 00000000
> [ 8.340049] Oops: 0002 [#2] SMP
> [ 8.340083] last sysfs file: /sys/devices/virtual/vtconsole/vtcon1/uevent
> [ 8.340083] Modules linked in: radeon(+) ttm rtl8180 ppdev drm_kms_helper parport_pc jedec_probe parport drm snd_ca0106 mac80211 snd_rawmidi snd_seq_device rtc_cmos rtc_core eeprom_93cx6 processor cfi_probe thermal container gen_probe thermal_sys cfi_util rtc_lib button snd_ac97_codec ac97_bus snd_pcm snd_timer amd_k7_agp amd76xrom(+) hwmon agpgart mtd snd soundcore cfg80211 i2c_algo_bit i2c_amd756 amd_rng rfkill snd_page_alloc i2c_core chipreg 3c59x map_funcs mii evdev psmouse shpchp sg serio_raw
> [ 8.340083]
> [ 8.340083] Pid: 1187, comm: modprobe Tainted: G D 2.6.35.11-smp #2 S2466 TIGER MPX/Unknown
> [ 8.340083] EIP: 0060:[<f905f797>] EFLAGS: 00010287 CPU: 0
> [ 8.340083] EIP is at r100_cp_fini+0x57/0xb0 [radeon]
> [ 8.340083] EAX: 00000000 EBX: f709e000 ECX: ffff8000 EDX: f90c9120
> [ 8.340083] ESI: 00000000 EDI: 00000e40 EBP: f6a0dda0 ESP: f6a0dd8c
> [ 8.340083] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
> [ 8.340083] Process modprobe (pid: 1187, ti=f6a0c000 task=f6b8ab20 task.ti=f6a0c000)
> [ 8.340083] Stack:
> [ 8.340083] f8e1821c f6a0dda0 f709e000 f663f000 00800005 f6a0ddac f9065760 f709e000
> [ 8.340083] <0> f6a0ddbc f902e293 f90b84bc f709e000 f6a0ddcc f902f3dc f663f000 f7125260
> [ 8.340083] <0> f6a0ddfc f902f517 f90b86dc f90c0c70 f7125260 fffffff4 0000003f 00000001
> [ 8.340083] Call Trace:
> [ 8.340083] [<f9065760>] ? r100_fini+0x10/0x70 [radeon]
> [ 8.340083] [<f902e293>] ? radeon_device_fini+0x33/0x80 [radeon]
> [ 8.340083] [<f902f3dc>] ? radeon_driver_unload_kms+0x2c/0x50 [radeon]
> [ 8.340083] [<f902f517>] ? radeon_driver_load_kms+0x117/0x1b0 [radeon]
> [ 8.340083] [<f8d1f82c>] ? drm_get_dev+0x2ac/0x490 [drm]
> [ 8.340083] [<f90a99f2>] ? radeon_pci_probe+0x12/0x14 [radeon]
> [ 8.340083] [<c14e974e>] ? pci_device_probe+0x5e/0x80
> [ 8.340083] [<c1561fdf>] ? driver_probe_device+0x7f/0x190
> [ 8.340083] [<c14e914b>] ? pci_match_device+0xab/0xc0
> [ 8.340083] [<c1562171>] ? __driver_attach+0x81/0x90
> [ 8.340083] [<c1561199>] ? bus_for_each_dev+0x49/0x70
> [ 8.340083] [<c1561d0e>] ? driver_attach+0x1e/0x20
> [ 8.340083] [<c15620f0>] ? __driver_attach+0x0/0x90
> [ 8.340083] [<c15618c2>] ? bus_add_driver+0xc2/0x2c0
> [ 8.340083] [<c14e9690>] ? pci_device_remove+0x0/0x40
> [ 8.340083] [<c15623a6>] ? driver_register+0x66/0x110
> [ 8.340083] [<c14e9975>] ? __pci_register_driver+0x45/0xb0
> [ 8.340083] [<f8d1a7c1>] ? drm_init+0xf1/0x100 [drm]
> [ 8.340083] [<f91a10b7>] ? radeon_init+0xb7/0xb9 [radeon]
> [ 8.340083] [<c1001242>] ? do_one_initcall+0x32/0x190
> [ 8.340083] [<f91a1000>] ? radeon_init+0x0/0xb9 [radeon]
> [ 8.340083] [<c1074ba3>] ? sys_init_module+0x93/0x1d0
> [ 8.340083] [<c10f20c2>] ? sys_write+0x42/0x70
> [ 8.340083] [<c199ac6c>] ? syscall_call+0x7/0xb
> [ 8.340083] Code: a9 00 00 01 00 74 36 b8 c7 10 00 00 83 c6 01 e8 a0 37 47 c8 3b 73 6c 73 4b 81 bb 90 00 00 00 40 0e 00 00 77 cf 8b 83 94 00 00 00 <89> 38 8b 83 94 00 00 00 8b 40 04 a9 00 00 01 00 75 ca 89 d8 e8
> [ 8.340083] EIP: [<f905f797>] r100_cp_fini+0x57/0xb0 [radeon] SS:ESP 0068:f6a0dd8c
> [ 8.340083] CR2: 0000000000000000
> [ 8.457876] ---[ end trace 7d61458dad6b2dff ]---
> [ 125.620673] lp0: using parport0 (interrupt-driven).
> [ 125.628435] lp0: console ready
> [ 427.840486] REISERFS (device sdb2): found reiserfs format "3.6" with standard journal
> [ 427.840535] REISERFS (device sdb2): using ordered data mode
> [ 427.850348] REISERFS (device sdb2): journal params: device sdb2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
> [ 427.853365] REISERFS (device sdb2): checking transaction log (sdb2)
> [ 427.902591] REISERFS (device sdb2): Using r5 hash to sort names
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2011-02-14 17:38 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-12-30 20:57 2.6.35.9 bug shown in dmesg (fwd) Russell Whitaker
2011-01-03 23:00 ` Stanislaw Gruszka
2011-01-06 6:21 ` Russell Whitaker
2011-01-06 16:19 ` Stanislaw Gruszka
2011-01-06 19:09 ` Russell Whitaker
2011-01-07 20:32 ` Stanislaw Gruszka
2011-02-14 2:50 ` Russell Whitaker
2011-02-14 17:31 ` Stanislaw Gruszka
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).