* problems with libata and ICH5 chipset.
@ 2004-06-19 17:34 James Courtier-Dutton
2004-06-19 17:50 ` Jeff Garzik
2004-06-19 18:05 ` James Courtier-Dutton
0 siblings, 2 replies; 3+ messages in thread
From: James Courtier-Dutton @ 2004-06-19 17:34 UTC (permalink / raw)
To: linux-ide
I am using kernel 2.6.7.
I enclose an extract from dmesg below.
I have 2 PATA devices, one DVD-ROM, one DVD-writer on ata1. (or hda and hdb)
I also have 2 SATA devices, both Hard Discs.
When I boot without libata enabled, and just use:-
ATA/ATAPI/MFM/RLL support -> Intel PIIXn chipsets support
I get access to: -
hda - PATA DVD-Writer
hdb - PATA DVD-ROM
hdc - SATA HD
hdd - SATA HD.
If I then enable:
SCSI device support -> SCSI low-level drivers -> Serial ATA (SATA)
support -> Intel PIIX/ICH SATA support
No PATA devices are accessible. I get:
sda - SATA HD
sdb - SATA HD
Is there any way that I can fix this using kernel options.
It seems that below, the PATA devices are being recognised, but then are
unable to be accessed.
Cheers
James
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
libata version 1.02 loaded.
ata_piix version 1.02
ata_piix: combined mode detected
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: PATA max UDMA/33 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
ata1: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
88:0407
ata1: dev 0 ATAPI, max UDMA/33
ata1: dev 1 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
88:0407
ata1: dev 1 ATAPI, max UDMA/33
ata1: dev 0 configured for UDMA/33
ata1: dev 1 configured for UDMA/33
scsi0 : ata_piix
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15
ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003
88:207f
ata2: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata2: dev 1 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003
88:207f
ata2: dev 1 ATA, max UDMA/133, 312581808 sectors: lba48
ata2: dev 0 configured for UDMA/133
ata2: dev 1 configured for UDMA/133
scsi1 : ata_piix
Vendor: ATA Model: ST3160023AS Rev: 3.18
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: ST3160023AS Rev: 3.18
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 >
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sdb: drive cache: write back
/dev/scsi/host1/bus0/target1/lun0: p1 p2 < p5 p6 >
Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: problems with libata and ICH5 chipset.
2004-06-19 17:34 problems with libata and ICH5 chipset James Courtier-Dutton
@ 2004-06-19 17:50 ` Jeff Garzik
2004-06-19 18:05 ` James Courtier-Dutton
1 sibling, 0 replies; 3+ messages in thread
From: Jeff Garzik @ 2004-06-19 17:50 UTC (permalink / raw)
To: James Courtier-Dutton; +Cc: linux-ide
James Courtier-Dutton wrote:
> I am using kernel 2.6.7.
> I enclose an extract from dmesg below.
> I have 2 PATA devices, one DVD-ROM, one DVD-writer on ata1. (or hda and
> hdb)
> I also have 2 SATA devices, both Hard Discs.
> When I boot without libata enabled, and just use:-
> ATA/ATAPI/MFM/RLL support -> Intel PIIXn chipsets support
> I get access to: -
> hda - PATA DVD-Writer
> hdb - PATA DVD-ROM
> hdc - SATA HD
> hdd - SATA HD.
>
> If I then enable:
> SCSI device support -> SCSI low-level drivers -> Serial ATA (SATA)
> support -> Intel PIIX/ICH SATA support
>
> No PATA devices are accessible. I get:
> sda - SATA HD
> sdb - SATA HD
>
> Is there any way that I can fix this using kernel options.
> It seems that below, the PATA devices are being recognised, but then are
> unable to be accessed.
Yeah, you need to disable combined mode and use the IDE driver for PATA.
Jeff
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: problems with libata and ICH5 chipset.
2004-06-19 17:34 problems with libata and ICH5 chipset James Courtier-Dutton
2004-06-19 17:50 ` Jeff Garzik
@ 2004-06-19 18:05 ` James Courtier-Dutton
1 sibling, 0 replies; 3+ messages in thread
From: James Courtier-Dutton @ 2004-06-19 18:05 UTC (permalink / raw)
To: James Courtier-Dutton; +Cc: linux-ide
I have managed to fix this myself, but I don't think it is very user
friendly.
I have to compile into the kernel the option:
ATA/ATAPI/MFM/RLL support -> Include IDE/ATA-2 DISK support
I can leave the kernel CD drivers as modules.
This works, even though I don't have any PATA hard discs.
So, I now have:
hda - PATA DVD-Writer
hdb - PATA DVD-ROM
sda - SATA HD
sdb - SATA HD.
See new dmesg extract:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: OPTORITEDVD RW DD0203, ATAPI CD/DVD-ROM drive
hdb: ATAPI DVD-ROM 16XMax, ATAPI CD/DVD-ROM drive
ide1: I/O resource 0x170-0x177 not free.
ide1: ports already in use, skipping probe
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
libata version 1.02 loaded.
ata_piix version 1.02
ata_piix: combined mode detected
ata: 0x1f0 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003
88:207f
ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata1: dev 1 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003
88:207f
ata1: dev 1 ATA, max UDMA/133, 312581808 sectors: lba48
ata1: dev 0 configured for UDMA/133
ata1: dev 1 configured for UDMA/133
scsi0 : ata_piix
Vendor: ATA Model: ST3160023AS Rev: 3.18
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: ST3160023AS Rev: 3.18
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sdb: drive cache: write back
/dev/scsi/host0/bus0/target1/lun0: p1 p2 < p5 p6 >
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
James Courtier-Dutton wrote:
> I am using kernel 2.6.7.
> I enclose an extract from dmesg below.
> I have 2 PATA devices, one DVD-ROM, one DVD-writer on ata1. (or hda and
> hdb)
> I also have 2 SATA devices, both Hard Discs.
> When I boot without libata enabled, and just use:-
> ATA/ATAPI/MFM/RLL support -> Intel PIIXn chipsets support
> I get access to: -
> hda - PATA DVD-Writer
> hdb - PATA DVD-ROM
> hdc - SATA HD
> hdd - SATA HD.
>
> If I then enable:
> SCSI device support -> SCSI low-level drivers -> Serial ATA (SATA)
> support -> Intel PIIX/ICH SATA support
>
> No PATA devices are accessible. I get:
> sda - SATA HD
> sdb - SATA HD
>
> Is there any way that I can fix this using kernel options.
> It seems that below, the PATA devices are being recognised, but then are
> unable to be accessed.
>
> Cheers
> James
>
>
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> libata version 1.02 loaded.
> ata_piix version 1.02
> ata_piix: combined mode detected
> PCI: Setting latency timer of device 0000:00:1f.2 to 64
> ata1: PATA max UDMA/33 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
> ata1: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
> 88:0407
> ata1: dev 0 ATAPI, max UDMA/33
> ata1: dev 1 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
> 88:0407
> ata1: dev 1 ATAPI, max UDMA/33
> ata1: dev 0 configured for UDMA/33
> ata1: dev 1 configured for UDMA/33
> scsi0 : ata_piix
> ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15
> ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003
> 88:207f
> ata2: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
> ata2: dev 1 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003
> 88:207f
> ata2: dev 1 ATA, max UDMA/133, 312581808 sectors: lba48
> ata2: dev 0 configured for UDMA/133
> ata2: dev 1 configured for UDMA/133
> scsi1 : ata_piix
> Vendor: ATA Model: ST3160023AS Rev: 3.18
> Type: Direct-Access ANSI SCSI revision: 05
> Vendor: ATA Model: ST3160023AS Rev: 3.18
> Type: Direct-Access ANSI SCSI revision: 05
> SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
> SCSI device sda: drive cache: write back
> /dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 >
> Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
> SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
> SCSI device sdb: drive cache: write back
> /dev/scsi/host1/bus0/target1/lun0: p1 p2 < p5 p6 >
> Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0
> -
> To unsubscribe from this list: send the line "unsubscribe linux-ide" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2004-06-19 18:05 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-06-19 17:34 problems with libata and ICH5 chipset James Courtier-Dutton
2004-06-19 17:50 ` Jeff Garzik
2004-06-19 18:05 ` James Courtier-Dutton
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).