* linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems]
[not found] ` <20041102014119.1a6096cc.akpm@osdl.org>
@ 2004-11-02 9:04 ` Christopher Chan
2004-11-02 10:07 ` Andrew Morton
0 siblings, 1 reply; 9+ messages in thread
From: Christopher Chan @ 2004-11-02 9:04 UTC (permalink / raw)
To: linux-ide; +Cc: Andrew Morton
Andrew Morton wrote:
> Christopher Chan <cchan@outblaze.com> wrote:
>
>>DOH. the kernel swapped the controller order on me...fstab entries
>> referred to the wrong device names...
>
>
> Eh? That shouldn't happen. Could you please generate a full report of
> this, send it to the appropriate list and cc myself?
>
> Although if that's the 2.6.9 behaviour it's probably a bit late to fix it
> up.
>
Hardware: Tyan mb with Serverworks chipset and onboard Promise controller.
The two disks on promise channel since Serverworks does not support ATA100
FC2 Installation will recognise the disks as hde and hdg
fstab is accordingly setup as so for swap (everything else are md)
Changing to a 2.6.9 kernel that has the promise driver compiled in will
change the disks to hda and hdc.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems]
2004-11-02 10:07 ` Andrew Morton
@ 2004-11-02 9:21 ` Christopher Chan
2004-11-02 10:26 ` Andrew Morton
0 siblings, 1 reply; 9+ messages in thread
From: Christopher Chan @ 2004-11-02 9:21 UTC (permalink / raw)
To: Andrew Morton; +Cc: linux-ide
>>Hardware: Tyan mb with Serverworks chipset and onboard Promise controller.
>> The two disks on promise channel since Serverworks does not support ATA100
>>
>>FC2 Installation will recognise the disks as hde and hdg
>>fstab is accordingly setup as so for swap (everything else are md)
>>
>>Changing to a 2.6.9 kernel that has the promise driver compiled in will
>>change the disks to hda and hdc.
>
>
> Could you send the dmesg output so we can see the probing activity?
>
With FC2 2.6.8-1.521smp
~~~~~~~~~~~~~~~~~~~~~~~~
Oct 14 11:34:50 spf5-3 kernel: RAMDISK driver initialized: 16 RAM disks
of 16384K size 1024 blocksize
Oct 14 11:34:50 spf5-3 kernel: Uniform Multi-Platform E-IDE driver
Revision: 7.00alpha2
Oct 14 11:34:50 spf5-3 kernel: ide: Assuming 33MHz system bus speed for
PIO modes; override with idebus=xx
Oct 14 11:34:50 spf5-3 nfslock: rpc.statd startup succeeded
Oct 14 11:34:50 spf5-3 kernel: PDC20267: IDE controller at PCI slot
0000:00:03.0
Oct 14 11:34:50 spf5-3 kernel: PDC20267: chipset revision 2
Oct 14 11:34:50 spf5-3 kernel: PDC20267: ROM enabled at 0xfead0000
Oct 14 11:34:50 spf5-3 kernel: PDC20267: 100%% native mode on irq 161
Oct 14 11:34:50 spf5-3 kernel: PDC20267: (U)DMA Burst Bit ENABLED
Primary MASTER Mode Secondary MASTER Mode.
Oct 14 11:34:50 spf5-3 kernel: ide2: BM-DMA at 0xdf00-0xdf07, BIOS
settings: hde:pio, hdf:pio
Oct 14 11:34:50 spf5-3 kernel: ide3: BM-DMA at 0xdf08-0xdf0f, BIOS
settings: hdg:pio, hdh:pio
Oct 14 11:34:50 spf5-3 kernel: hde: Maxtor 5T040H4, ATA DISK drive
Oct 14 11:34:50 spf5-3 kernel: Using deadline io scheduler
Oct 14 11:34:50 spf5-3 kernel: ide2 at 0xdfe0-0xdfe7,0xdfae on irq 161
Oct 14 11:34:50 spf5-3 kernel: hdg: Maxtor 5T040H4, ATA DISK drive
Oct 14 11:34:50 spf5-3 kernel: ide3 at 0xdfa0-0xdfa7,0xdfaa on irq 161
Oct 14 11:34:50 spf5-3 kernel: SvrWks OSB4: IDE controller at PCI slot
0000:00:0f.1
Oct 14 11:34:50 spf5-3 kernel: PCI: Enabling device 0000:00:0f.1 (0000
-> 0001)
Oct 14 11:34:50 spf5-3 kernel: SvrWks OSB4: chipset revision 0
Oct 14 11:34:50 spf5-3 kernel: SvrWks OSB4: not 100%% native mode: will
probe irqs later
Oct 14 11:34:50 spf5-3 kernel: ide0: BM-DMA at 0xffa0-0xffa7, BIOS
settings: hda:pio, hdb:pio
Oct 14 11:34:50 spf5-3 kernel: ide1: BM-DMA at 0xffa8-0xffaf, BIOS
settings: hdc:pio, hdd:pio
Oct 14 11:34:50 spf5-3 kernel: hde: max request size: 128KiB
Oct 14 11:34:50 spf5-3 kernel: hde: 80043264 sectors (40982 MB)
w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
Oct 14 11:34:50 spf5-3 kernel: hde: hde1 hde2 hde3 hde4 < hde5 >
Oct 14 11:34:50 spf5-3 kernel: hdg: max request size: 128KiB
Oct 14 11:34:50 spf5-3 kernel: hdg: 80043264 sectors (40982 MB)
w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
Oct 14 11:34:50 spf5-3 kernel: hdg: hdg1 hdg2 hdg3 hdg4 < hdg5 >
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
With 2.6.9
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Using deadline io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 2.6.2)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20267: IDE controller at PCI slot 0000:00:03.0
PDC20267: chipset revision 2
PDC20267: ROM enabled at 0xfead0000
PDC20267: 100% native mode on irq 31
PDC20267: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
Mode.
ide0: BM-DMA at 0xdf00-0xdf07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xdf08-0xdf0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: Maxtor 5T040H4, ATA DISK drive
ide0 at 0xdfe0-0xdfe7,0xdfae on irq 31
Probing IDE interface ide1...
hdc: Maxtor 5T040H4, ATA DISK drive
ide1 at 0xdfa0-0xdfa7,0xdfaa on irq 31
SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1
PCI: Enabling device 0000:00:0f.1 (0000 -> 0001)
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xffa0-0xffa7, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4 < hda5 >
hdc: max request size: 128KiB
hdc: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hdc: cache flushes not supported
hdc: hdc1 hdc2 hdc3 hdc4 < hdc5 >
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems]
2004-11-02 9:04 ` linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems] Christopher Chan
@ 2004-11-02 10:07 ` Andrew Morton
2004-11-02 9:21 ` Christopher Chan
0 siblings, 1 reply; 9+ messages in thread
From: Andrew Morton @ 2004-11-02 10:07 UTC (permalink / raw)
To: Christopher Chan; +Cc: linux-ide
Christopher Chan <cchan@outblaze.com> wrote:
>
> Andrew Morton wrote:
> > Christopher Chan <cchan@outblaze.com> wrote:
> >
> >>DOH. the kernel swapped the controller order on me...fstab entries
> >> referred to the wrong device names...
> >
> >
> > Eh? That shouldn't happen. Could you please generate a full report of
> > this, send it to the appropriate list and cc myself?
> >
> > Although if that's the 2.6.9 behaviour it's probably a bit late to fix it
> > up.
> >
>
> Hardware: Tyan mb with Serverworks chipset and onboard Promise controller.
> The two disks on promise channel since Serverworks does not support ATA100
>
> FC2 Installation will recognise the disks as hde and hdg
> fstab is accordingly setup as so for swap (everything else are md)
>
> Changing to a 2.6.9 kernel that has the promise driver compiled in will
> change the disks to hda and hdc.
Could you send the dmesg output so we can see the probing activity?
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems]
2004-11-02 9:21 ` Christopher Chan
@ 2004-11-02 10:26 ` Andrew Morton
2004-11-02 16:40 ` Alan Cox
0 siblings, 1 reply; 9+ messages in thread
From: Andrew Morton @ 2004-11-02 10:26 UTC (permalink / raw)
To: Christopher Chan; +Cc: linux-ide, Alan Cox
Christopher Chan <cchan@outblaze.com> wrote:
>
> >>Hardware: Tyan mb with Serverworks chipset and onboard Promise controller.
> >> The two disks on promise channel since Serverworks does not support ATA100
> >>
> >>FC2 Installation will recognise the disks as hde and hdg
> >>fstab is accordingly setup as so for swap (everything else are md)
> >>
> >>Changing to a 2.6.9 kernel that has the promise driver compiled in will
> >>change the disks to hda and hdc.
> >
> >
> > Could you send the dmesg output so we can see the probing activity?
> >
>
> With FC2 2.6.8-1.521smp
>
> ~~~~~~~~~~~~~~~~~~~~~~~~
> Oct 14 11:34:50 spf5-3 kernel: RAMDISK driver initialized: 16 RAM disks
> of 16384K size 1024 blocksize
> Oct 14 11:34:50 spf5-3 kernel: Uniform Multi-Platform E-IDE driver
> Revision: 7.00alpha2
> Oct 14 11:34:50 spf5-3 kernel: ide: Assuming 33MHz system bus speed for
> PIO modes; override with idebus=xx
> Oct 14 11:34:50 spf5-3 nfslock: rpc.statd startup succeeded
> Oct 14 11:34:50 spf5-3 kernel: PDC20267: IDE controller at PCI slot
> 0000:00:03.0
> Oct 14 11:34:50 spf5-3 kernel: PDC20267: chipset revision 2
> Oct 14 11:34:50 spf5-3 kernel: PDC20267: ROM enabled at 0xfead0000
> Oct 14 11:34:50 spf5-3 kernel: PDC20267: 100%% native mode on irq 161
> Oct 14 11:34:50 spf5-3 kernel: PDC20267: (U)DMA Burst Bit ENABLED
> Primary MASTER Mode Secondary MASTER Mode.
> Oct 14 11:34:50 spf5-3 kernel: ide2: BM-DMA at 0xdf00-0xdf07, BIOS
> settings: hde:pio, hdf:pio
> Oct 14 11:34:50 spf5-3 kernel: ide3: BM-DMA at 0xdf08-0xdf0f, BIOS
> settings: hdg:pio, hdh:pio
> Oct 14 11:34:50 spf5-3 kernel: hde: Maxtor 5T040H4, ATA DISK drive
> Oct 14 11:34:50 spf5-3 kernel: Using deadline io scheduler
> Oct 14 11:34:50 spf5-3 kernel: ide2 at 0xdfe0-0xdfe7,0xdfae on irq 161
> Oct 14 11:34:50 spf5-3 kernel: hdg: Maxtor 5T040H4, ATA DISK drive
> Oct 14 11:34:50 spf5-3 kernel: ide3 at 0xdfa0-0xdfa7,0xdfaa on irq 161
> Oct 14 11:34:50 spf5-3 kernel: SvrWks OSB4: IDE controller at PCI slot
> 0000:00:0f.1
> Oct 14 11:34:50 spf5-3 kernel: PCI: Enabling device 0000:00:0f.1 (0000
> -> 0001)
> Oct 14 11:34:50 spf5-3 kernel: SvrWks OSB4: chipset revision 0
> Oct 14 11:34:50 spf5-3 kernel: SvrWks OSB4: not 100%% native mode: will
> probe irqs later
> Oct 14 11:34:50 spf5-3 kernel: ide0: BM-DMA at 0xffa0-0xffa7, BIOS
> settings: hda:pio, hdb:pio
> Oct 14 11:34:50 spf5-3 kernel: ide1: BM-DMA at 0xffa8-0xffaf, BIOS
> settings: hdc:pio, hdd:pio
> Oct 14 11:34:50 spf5-3 kernel: hde: max request size: 128KiB
> Oct 14 11:34:50 spf5-3 kernel: hde: 80043264 sectors (40982 MB)
> w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
> Oct 14 11:34:50 spf5-3 kernel: hde: hde1 hde2 hde3 hde4 < hde5 >
> Oct 14 11:34:50 spf5-3 kernel: hdg: max request size: 128KiB
> Oct 14 11:34:50 spf5-3 kernel: hdg: 80043264 sectors (40982 MB)
> w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
> Oct 14 11:34:50 spf5-3 kernel: hdg: hdg1 hdg2 hdg3 hdg4 < hdg5 >
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>
> With 2.6.9
>
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> Using deadline io scheduler
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> Compaq SMART2 Driver (v 2.6.0)
> HP CISS Driver (v 2.6.2)
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> PDC20267: IDE controller at PCI slot 0000:00:03.0
> PDC20267: chipset revision 2
> PDC20267: ROM enabled at 0xfead0000
> PDC20267: 100% native mode on irq 31
> PDC20267: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
> Mode.
> ide0: BM-DMA at 0xdf00-0xdf07, BIOS settings: hda:pio, hdb:pio
> ide1: BM-DMA at 0xdf08-0xdf0f, BIOS settings: hdc:pio, hdd:pio
> Probing IDE interface ide0...
> hda: Maxtor 5T040H4, ATA DISK drive
> ide0 at 0xdfe0-0xdfe7,0xdfae on irq 31
> Probing IDE interface ide1...
> hdc: Maxtor 5T040H4, ATA DISK drive
> ide1 at 0xdfa0-0xdfa7,0xdfaa on irq 31
> SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1
> PCI: Enabling device 0000:00:0f.1 (0000 -> 0001)
> SvrWks OSB4: chipset revision 0
> SvrWks OSB4: not 100% native mode: will probe irqs later
> ide2: BM-DMA at 0xffa0-0xffa7, BIOS settings: hde:pio, hdf:pio
> ide3: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdg:pio, hdh:pio
> Probing IDE interface ide2...
> Probing IDE interface ide3...
> Probing IDE interface ide2...
> Probing IDE interface ide3...
> Probing IDE interface ide4...
> ide4: Wait for ready failed before probe !
> Probing IDE interface ide5...
> ide5: Wait for ready failed before probe !
> hda: max request size: 128KiB
> hda: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
> hda: cache flushes not supported
> hda: hda1 hda2 hda3 hda4 < hda5 >
> hdc: max request size: 128KiB
> hdc: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
> hdc: cache flushes not supported
> hdc: hdc1 hdc2 hdc3 hdc4 < hdc5 >
>
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Well the problem is that "Wait for ready" thing. Was that an alanism?
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems]
2004-11-02 10:26 ` Andrew Morton
@ 2004-11-02 16:40 ` Alan Cox
2004-11-03 6:57 ` Christopher Chan
0 siblings, 1 reply; 9+ messages in thread
From: Alan Cox @ 2004-11-02 16:40 UTC (permalink / raw)
To: Andrew Morton; +Cc: Christopher Chan, linux-ide
On Maw, 2004-11-02 at 10:26, Andrew Morton wrote:
> Well the problem is that "Wait for ready" thing. Was that an alanism?
What are you on about ? The problem is that in the two traces his
serverworks has moved from ide0 to ide2.
Alan
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems]
2004-11-02 16:40 ` Alan Cox
@ 2004-11-03 6:57 ` Christopher Chan
2004-11-03 13:00 ` Bartlomiej Zolnierkiewicz
0 siblings, 1 reply; 9+ messages in thread
From: Christopher Chan @ 2004-11-03 6:57 UTC (permalink / raw)
To: Alan Cox; +Cc: Andrew Morton, linux-ide
> What are you on about ? The problem is that in the two traces his
> serverworks has moved from ide0 to ide2.
Here's the other case on another box that has onboard Promise plus an
add-on Promise card:
2.6.9:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20267: IDE controller at PCI slot 0000:01:02.0
PDC20267: chipset revision 2
PDC20267: ROM enabled at 0xfebd0000
PDC20267: 100% native mode on irq 27
PDC20267: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide0: BM-DMA at 0xef00-0xef07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xef08-0xef0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
PDC20267: IDE controller at PCI slot 0000:00:03.0
PDC20267: chipset revision 2
PDC20267: ROM enabled at 0xfeae0000
PDC20267: 100% native mode on irq 31
PDC20267: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
Mode.
ide2: BM-DMA at 0xdf00-0xdf07, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xdf08-0xdf0f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hde: Maxtor 5T040H4, ATA DISK drive
ide2 at 0xdfe0-0xdfe7,0xdfae on irq 31
Probing IDE interface ide3...
hdg: Maxtor 5T040H4, ATA DISK drive
ide3 at 0xdfa0-0xdfa7,0xdfaa on irq 31
SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
ide4: BM-DMA at 0xffa0-0xffa7, BIOS settings: hdi:pio, hdj:pio
ide5: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdk:pio, hdl:pio
Probing IDE interface ide4...
Probing IDE interface ide5...
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide4...
Probing IDE interface ide5...
hde: max request size: 128KiB
hde: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hde: cache flushes not supported
hde: hde1 hde2 hde3 hde4 < hde5 >
hdg: max request size: 128KiB
hdg: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hdg: cache flushes not supported
2.6.8-1.521smp (FC2):
Oct 14 04:46:49 spf0 kernel: ide: Assuming 33MHz system bus speed for
PIO modes; override with idebus=xx
Oct 14 04:46:49 spf0 kernel: PDC20267: IDE controller at PCI slot
0000:01:02.0
Oct 14 04:46:49 spf0 kernel: PDC20267: chipset revision 2
Oct 14 04:46:49 spf0 kernel: PDC20267: ROM enabled at 0xfebd0000
Oct 14 04:46:49 spf0 kernel: PDC20267: 100%% native mode on irq 153
Oct 14 04:46:49 spf0 kernel: PDC20267: (U)DMA Burst Bit ENABLED Primary
PCI Mode Secondary PCI Mode.
Oct 14 04:46:49 spf0 kernel: ide2: BM-DMA at 0xef00-0xef07, BIOS
settings: hde:pio, hdf:pio
Oct 14 04:46:49 spf0 kernel: ide3: BM-DMA at 0xef08-0xef0f, BIOS
settings: hdg:pio, hdh:pio
Oct 14 04:46:49 spf0 kernel: PDC20267: IDE controller at PCI slot
0000:00:03.0
Oct 14 04:46:49 spf0 kernel: PDC20267: chipset revision 2
Oct 14 04:46:49 spf0 kernel: PDC20267: ROM enabled at 0xfeae0000
Oct 14 04:46:49 spf0 kernel: PDC20267: 100%% native mode on irq 161
Oct 14 04:46:49 spf0 kernel: PDC20267: (U)DMA Burst Bit ENABLED Primary
MASTER Mode Secondary MASTER Mode.
Oct 14 04:46:49 spf0 kernel: ide4: BM-DMA at 0xdf00-0xdf07, BIOS
settings: hdi:pio, hdj:pio
Oct 14 04:46:49 spf0 kernel: ide5: BM-DMA at 0xdf08-0xdf0f, BIOS
settings: hdk:pio, hdl:pio
Oct 14 04:46:49 spf0 kernel: hdi: Maxtor 5T040H4, ATA DISK drive
Oct 14 04:46:49 spf0 kernel: Using cfq io scheduler
Oct 14 04:46:49 spf0 kernel: ide4 at 0xdfe0-0xdfe7,0xdfae on irq 161
Oct 14 04:46:49 spf0 kernel: hdk: Maxtor 5T040H4, ATA DISK drive
Oct 14 04:46:49 spf0 kernel: ide5 at 0xdfa0-0xdfa7,0xdfaa on irq 161
Oct 14 04:46:49 spf0 kernel: SvrWks OSB4: IDE controller at PCI slot
0000:00:0f.1
Oct 14 04:46:49 spf0 kernel: SvrWks OSB4: chipset revision 0
Oct 14 04:46:49 spf0 kernel: SvrWks OSB4: not 100%% native mode: will
probe irqs later
Oct 14 04:46:49 spf0 kernel: ide0: BM-DMA at 0xffa0-0xffa7, BIOS
settings: hda:pio, hdb:pio
Oct 14 04:46:49 spf0 kernel: ide1: BM-DMA at 0xffa8-0xffaf, BIOS
settings: hdc:pio, hdd:pio
Oct 14 04:46:49 spf0 kernel: hdi: max request size: 128KiB
Oct 14 04:46:49 spf0 kernel: hdi: 80043264 sectors (40982 MB) w/2048KiB
Cache, CHS=65535/16/63, UDMA(100)
Oct 14 04:46:49 spf0 kernel: hdi: hdi1 hdi2 hdi3 hdi4 < hdi5 >
Oct 14 04:46:49 spf0 kernel: hdk: max request size: 128KiB
Oct 14 04:46:49 spf0 kernel: hdk: 80043264 sectors (40982 MB) w/2048KiB
Cache, CHS=65535/16/63, UDMA(100)
Oct 14 04:46:49 spf0 kernel: hdk: hdk1 hdk2 hdk3 hdk4 < hdk5 >
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems]
2004-11-03 6:57 ` Christopher Chan
@ 2004-11-03 13:00 ` Bartlomiej Zolnierkiewicz
2004-11-03 15:51 ` Christopher Chan
0 siblings, 1 reply; 9+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2004-11-03 13:00 UTC (permalink / raw)
To: Christopher Chan; +Cc: Alan Cox, Andrew Morton, linux-ide
Do you have CONFIG_BLK_DEV_OFFBOARD=y in your config?
On Wed, 03 Nov 2004 14:57:36 +0800, Christopher Chan <cchan@outblaze.com> wrote:
>
> > What are you on about ? The problem is that in the two traces his
> > serverworks has moved from ide0 to ide2.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems]
2004-11-03 13:00 ` Bartlomiej Zolnierkiewicz
@ 2004-11-03 15:51 ` Christopher Chan
2004-11-03 17:01 ` Bartlomiej Zolnierkiewicz
0 siblings, 1 reply; 9+ messages in thread
From: Christopher Chan @ 2004-11-03 15:51 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz; +Cc: Alan Cox, Andrew Morton, linux-ide
Bartlomiej Zolnierkiewicz wrote:
> Do you have CONFIG_BLK_DEV_OFFBOARD=y in your config?
Yes....
>
> On Wed, 03 Nov 2004 14:57:36 +0800, Christopher Chan <cchan@outblaze.com> wrote:
>
>>>What are you on about ? The problem is that in the two traces his
>>>serverworks has moved from ide0 to ide2.
>
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems]
2004-11-03 15:51 ` Christopher Chan
@ 2004-11-03 17:01 ` Bartlomiej Zolnierkiewicz
0 siblings, 0 replies; 9+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2004-11-03 17:01 UTC (permalink / raw)
To: Christopher Chan; +Cc: Alan Cox, Andrew Morton, linux-ide
On Wed, 03 Nov 2004 23:51:29 +0800, Christopher Chan <cchan@outblaze.com> wrote:
> Bartlomiej Zolnierkiewicz wrote:
> > Do you have CONFIG_BLK_DEV_OFFBOARD=y in your config?
>
> Yes....
This explains the issue...
> > On Wed, 03 Nov 2004 14:57:36 +0800, Christopher Chan <cchan@outblaze.com> wrote:
> >
> >>>What are you on about ? The problem is that in the two traces his
> >>>serverworks has moved from ide0 to ide2.
> >
> >
>
>
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2004-11-03 17:01 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <418741EB.3080701@outblaze.com>
[not found] ` <20041102011918.2b453e21.akpm@osdl.org>
[not found] ` <4187478A.1040002@outblaze.com>
[not found] ` <20041102014119.1a6096cc.akpm@osdl.org>
2004-11-02 9:04 ` linux 2.6.9 controller order reordered. was: [Re: linux 2.6.9 still having network code problems] Christopher Chan
2004-11-02 10:07 ` Andrew Morton
2004-11-02 9:21 ` Christopher Chan
2004-11-02 10:26 ` Andrew Morton
2004-11-02 16:40 ` Alan Cox
2004-11-03 6:57 ` Christopher Chan
2004-11-03 13:00 ` Bartlomiej Zolnierkiewicz
2004-11-03 15:51 ` Christopher Chan
2004-11-03 17:01 ` Bartlomiej Zolnierkiewicz
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).