linux-ide.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* TX4000 RAID and sata_promise
@ 2005-08-16  5:30 Yuri Kirsanov
  2005-08-16 13:10 ` Tyler
  0 siblings, 1 reply; 22+ messages in thread
From: Yuri Kirsanov @ 2005-08-16  5:30 UTC (permalink / raw)
  To: linux-ide

Good day. I have Mandrake Linux LE2005 with custom kernel
2.6.12.2+Reiser4 patch+TX4000 patch
(First part of this patch
http://www.mail-archive.com/linux-ide@vger.kernel.org/msg00150.html
second part failed and I can't figure out how to apply it). When i do
'modprobe sata_promise' it only says:

Aug 14 19:24:21 mandr kernel: libata version 1.11 loaded.
Aug 14 19:24:21 mandr kernel: sata_promise version 1.01
Aug 14 19:24:21 mandr kernel: PCI: Found IRQ 9 for device 0000:01:09.0
Aug 14 19:24:21 mandr kernel: ata1: PATA max UDMA/133 cmd 0xC89FE200 ctl
0xC89FE238 bmdma 0x0 irq 9
Aug 14 19:24:21 mandr kernel: ata2: PATA max UDMA/133 cmd 0xC89FE280 ctl
0xC89FE2B8 bmdma 0x0 irq 9
Aug 14 19:24:21 mandr kernel: ata3: PATA max UDMA/133 cmd 0xC89FE300 ctl
0xC89FE338 bmdma 0x0 irq 9
Aug 14 19:24:21 mandr kernel: ata4: PATA max UDMA/133 cmd 0xC89FE380 ctl
0xC89FE3B8 bmdma 0x0 irq 9
Aug 14 19:24:21 mandr kernel: ata1: no device found (phy stat 00000000)
Aug 14 19:24:21 mandr kernel: scsi0 : sata_promise
Aug 14 19:24:21 mandr kernel: ata2: no device found (phy stat 00000000)
Aug 14 19:24:21 mandr kernel: scsi1 : sata_promise
Aug 14 19:24:21 mandr kernel: ata3: no device found (phy stat 00000000)
Aug 14 19:24:21 mandr kernel: scsi2 : sata_promise
Aug 14 19:24:22 mandr kernel: ata4: no device found (phy stat 00000000)
Aug 14 19:24:22 mandr kernel: scsi3 : sata_promise

 I have 2 hard drives connected to TX4000 on IDE1 channel, in stripe
mode. I've set up raid in TX4000 BIOS, but in Linux it can't see my
hard disks, and so I have no /dev/sd* and can't mount this hard
disks...Could you please help me, what am I doing wrong?
I've already tried to install sata_promise both as a module and as a
built-in...I've tried to do 'modprobe sd_mod' first, it only says
'SCSI system initialized'. I'm completely stuck with it :(

 PS. I have ASUS i815 CUSL2-M motherboard.



^ permalink raw reply	[flat|nested] 22+ messages in thread
* TX4000 RAID and sata_promise
@ 2005-08-28 17:08 Yuri Kirsanov
  2005-08-29  8:57 ` Erik Slagter
  0 siblings, 1 reply; 22+ messages in thread
From: Yuri Kirsanov @ 2005-08-28 17:08 UTC (permalink / raw)
  To: linux-ide; +Cc: jgarzik

Yes, with another hard drive, which is error-free everything works
just fine, with one exception:

libata version 1.11 loaded.
sata_promise version 1.01
PCI: Found IRQ 5 for device 0000:01:0a.0
ata1: SATA max UDMA/133 cmd 0xCC802200 ctl 0xCC802238 bmdma 0x0 irq 5
ata2: SATA max UDMA/133 cmd 0xCC802280 ctl 0xCC8022B8 bmdma 0x0 irq 5
ata3: PATA max UDMA/133 cmd 0xCC802300 ctl 0xCC802338 bmdma 0x0 irq 5
ata4: PATA max UDMA/133 cmd 0xCC802380 ctl 0xCC8023B8 bmdma 0x0 irq 5
ata1: dev 0 cfg 49:0f00 82:346b 83:5b01 84:4003 85:3469 86:1a01 87:4003 88:407f
ata1: dev 0 ATA-5, max UDMA/133, 40132503 sectors: LBA
ata1: dev 0 configured for UDMA/133
scsi0 : sata_promise
ATA: abnormal status 0x8 on port 0xCC80229C
ata2: disabling port
scsi1 : sata_promise
ATA: abnormal status 0x8 on port 0xCC80231C
ata3: disabling port
scsi2 : sata_promise
ATA: abnormal status 0x8 on port 0xCC80239C
ata4: disabling port
scsi3 : sata_promise
  Vendor: ATA       Model: MAXTOR 6L020J1    Rev: A93.
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 40132503 512-byte hdwr sectors (20548 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 40132503 512-byte hdwr sectors (20548 MB)
SCSI device sda: drive cache: write back
 /dev/scsi/host0/bus0/target0/lun0: unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0

As you can see, only one hard drive is connected to my TX4000, and
because I disabled sata check I get abnormal status on another ports.
But my hard drive works just fine! I'm looking forward to attach
another hard drive and create RAID in TX4000 BIOS. I wonder, will
sata_promise detect two disks on two ports, or just one thru BIOS?


^ permalink raw reply	[flat|nested] 22+ messages in thread
* TX4000 RAID and sata_promise
@ 2005-08-28 14:46 Yuri Kirsanov
  0 siblings, 0 replies; 22+ messages in thread
From: Yuri Kirsanov @ 2005-08-28 14:46 UTC (permalink / raw)
  To: linux-ide; +Cc: jgarzik

Look's like I've found solution. I've checked libata_core.c and found
following strings in it (line 1427):

      if (sata_dev_present(ap))
        ata_port_probe(ap);
      else {
                sstatus = scr_read(ap, SCR_STATUS);
                printk(KERN_INFO "ata%u: no device found (phy stat %08x)\n",
                       ap->id, sstatus);
                ata_port_disable(ap);
        }

For experiment, I made following changes:

//      if (sata_dev_present(ap))
        ata_port_probe(ap);
/*      else {
                sstatus = scr_read(ap, SCR_STATUS);
                printk(KERN_INFO "ata%u: no device found (phy stat %08x)\n",
                       ap->id, sstatus);
                ata_port_disable(ap);
        }
*/

So, now it's always do port-probe, and here is the result:

libata version 1.12 loaded.
sata_promise version 1.02
PCI: Found IRQ 9 for device 0000:01:0a.0
ata1: PATA max UDMA/133 cmd 0xCC81C200 ctl 0xCC81C238 bmdma 0x0 irq 9
ata2: PATA max UDMA/133 cmd 0xCC81C280 ctl 0xCC81C2B8 bmdma 0x0 irq 9
ata3: PATA max UDMA/133 cmd 0xCC81C300 ctl 0xCC81C338 bmdma 0x0 irq 9
ata4: PATA max UDMA/133 cmd 0xCC81C380 ctl 0xCC81C3B8 bmdma 0x0 irq 9
ATA: abnormal status 0x8 on port 0xCC81C21C
ata1: disabling port
scsi0 : sata_promise
ata2: dev 0 cfg 49:0b00 82:346b 83:4208 84:4000 85:3461 86:0000 87:4000 88:101f
ata2: dev 0 ATA, max UDMA/66, 17840592 sectors:
ata2(0): applying bridge limits
ata2: dev 0 configured for UDMA/66
scsi1 : sata_promise
ATA: abnormal status 0x8 on port 0xCC81C31C
ata3: disabling port
scsi2 : sata_promise
ATA: abnormal status 0x8 on port 0xCC81C39C
ata4: disabling port
scsi3 : sata_promise
  Vendor: ATA       Model: FUJITSU MPF3102A  Rev: 5C18
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 17840592 512-byte hdwr sectors (9134 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 17840592 512-byte hdwr sectors (9134 MB)
SCSI device sda: drive cache: write back
 sda:<4>ata2: status=0x51 { DriveReady SeekComplete Error }
ata2: error=0x84 { DriveStatusError BadCRC }
 sda1
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0,  type 0

As you can see, my device is found ok, I was able to format it and
mount it. Seek errors may be because of bad disk state, I'm trying to
make some checks on it. I understand, that I made really incorrect
commenting out, but maybe now somebody will be able to make this
driver work correctly with an PATA devices?


^ permalink raw reply	[flat|nested] 22+ messages in thread
* TX4000 RAID and sata_promise
@ 2005-08-28 13:33 Yuri Kirsanov
  2005-08-29  8:52 ` Erik Slagter
  0 siblings, 1 reply; 22+ messages in thread
From: Yuri Kirsanov @ 2005-08-28 13:33 UTC (permalink / raw)
  To: linux-ide

Good day. I've tried latest kernel 2.6.13-rc7, TX4000 support seems to
be in sata_promise already. After startup I see following in dmesg:

libata version 1.12 loaded.
sata_promise version 1.02
PCI: Found IRQ 5 for device 0000:01:09.0
ata1: PATA max UDMA/133 cmd 0xCC81C200 ctl 0xCC81C238 bmdma 0x0 irq 5
ata2: PATA max UDMA/133 cmd 0xCC81C280 ctl 0xCC81C2B8 bmdma 0x0 irq 5
ata3: PATA max UDMA/133 cmd 0xCC81C300 ctl 0xCC81C338 bmdma 0x0 irq 5
ata4: PATA max UDMA/133 cmd 0xCC81C380 ctl 0xCC81C3B8 bmdma 0x0 irq 5
ata1: no device found (phy stat 00000000)
scsi0 : sata_promise
ata2: no device found (phy stat 00000000)
scsi1 : sata_promise
ata3: no device found (phy stat 00000000)
scsi2 : sata_promise
ata4: no device found (phy stat 00000000)
scsi3 : sata_promise


Anybody has any ideas? As I can see, my TX4000 is found by
sata_promise, it even detects it's UDMA modes, but it still can't find
any of my hard drives, while TX4000 BIOS shows all of them ok.

Jeff, please, can you comment this situation???


^ permalink raw reply	[flat|nested] 22+ messages in thread
* TX4000 RAID and sata_promise
@ 2005-08-23  8:08 Yuri Kirsanov
  0 siblings, 0 replies; 22+ messages in thread
From: Yuri Kirsanov @ 2005-08-23  8:08 UTC (permalink / raw)
  To: linux-ide

So, no PATA controllers like TX4000 can be supported under Linux?
Anybody, please answer...


^ permalink raw reply	[flat|nested] 22+ messages in thread
* RE: TX4000 RAID and sata_promise
@ 2005-08-22  6:28 Allen Bolderoff
  0 siblings, 0 replies; 22+ messages in thread
From: Allen Bolderoff @ 2005-08-22  6:28 UTC (permalink / raw)
  To: Yuri Kirsanov, linux-ide

Seems to me than no one with the skills is interested. (not a dig at
anyone, so please don't take it that way)

That is of course except us with the problem. 

It's a case of fix it yourself, or suck it a wait.

I believe it is a problem with the sata_promise stuff, as we are seeing
similar issues with the S150 TX4 and the SATAII TX4.


> -----Original Message-----
> From: linux-ide-owner@vger.kernel.org [mailto:linux-ide-
> owner@vger.kernel.org] On Behalf Of Yuri Kirsanov
> Sent: Saturday, 20 August 2005 6:17 PM
> To: linux-ide@vger.kernel.org
> Subject: TX4000 RAID and sata_promise
> 
> Good day! So, nobody can help me with TX4000?
> 
> -
> To unsubscribe from this list: send the line "unsubscribe linux-ide"
in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply	[flat|nested] 22+ messages in thread
* TX4000 RAID and sata_promise
@ 2005-08-20  8:46 Yuri Kirsanov
  0 siblings, 0 replies; 22+ messages in thread
From: Yuri Kirsanov @ 2005-08-20  8:46 UTC (permalink / raw)
  To: linux-ide

Good day! So, nobody can help me with TX4000?


^ permalink raw reply	[flat|nested] 22+ messages in thread
* TX4000 RAID and sata_promise
@ 2005-06-23 17:05 Yuri Kirsanov
  2005-08-18 17:11 ` Erik Slagter
  0 siblings, 1 reply; 22+ messages in thread
From: Yuri Kirsanov @ 2005-06-23 17:05 UTC (permalink / raw)
  To: linux-ide; +Cc: Erik Slagter

Here's my dmesg with sata_promise compiled-in kernel:

Linux version 2.6.12.4-10flh (root@mandr) (gcc version 3.4.3 (Mandrakelinux 10.2 3.4.3-7mdk)) #3 SMP Tue Aug 16 21:34:11 MSD 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000beeb000 (usable)
 BIOS-e820: 000000000beeb000 - 000000000beef000 (ACPI data)
 BIOS-e820: 000000000beef000 - 000000000beff000 (reserved)
 BIOS-e820: 000000000beff000 - 000000000bf00000 (ACPI NVS)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
190MB LOWMEM available.
On node 0 totalpages: 48875
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 44779 pages, LIFO batch:15
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ASUS                                  ) @ 0x000f70e0
ACPI: RSDT (v001 ASUS   CUSL2-M  0x30303031 MSFT 0x31313031) @ 0x0beeb000
ACPI: FADT (v001 ASUS   CUSL2-M  0x30303031 MSFT 0x31313031) @ 0x0beeb080
ACPI: BOOT (v001 ASUS   CUSL2-M  0x30303031 MSFT 0x31313031) @ 0x0beeb040
ACPI: DSDT (v001   ASUS CUSL2-M  0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0xe408
Allocating PCI resources starting at 0bf00000 (gap: 0bf00000:f40f0000)
Built 1 zonelists
Kernel command line: root=/dev/hda1 acpi=ht resume=/dev/hda5 ide2=0xd400,0xd002
ide_setup: ide2=0xd400,0xd002
 -- OBSOLETE OPTION, WILL BE REMOVED SOON!
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (011bf000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 804.257 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 189304k/195500k available (1999k kernel code, 5640k reserved, 813k data, 248k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1593.34 BogoMIPS (lpj=796672)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel Pentium III (Coppermine) stepping 01
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
CPU0 attaching sched-domain:
 domain 0: span 01
  groups: 01
  domain 1: span 01
   groups: 01
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 189k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0d90, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbd70
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbda0, dseg 0xf0000
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Discovered primary peer bus fe [IRQ]
PCI: Using IRQ router PIIX/ICH [8086/2440] at 0000:00:1f.0
PCI: IRQ 0 for device 0000:01:02.0 doesn't match PIRQ mask - try pci=usepirqmask
pnp: 00:12: ioport range 0x290-0x297 has been reserved
pnp: 00:12: ioport range 0x3f0-0x3f1 has been reserved
pnp: 00:12: ioport range 0xe400-0xe47f has been reserved
pnp: 00:12: ioport range 0xec00-0xec3f has been reserved
Simple Boot Flag at 0x3a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1124384084.409:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 controller doesn't have AUX irq; using default 0xc
PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 112
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 2
ICH2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: FUJITSU MPC3043AT, ATA DISK drive
hdb: ST320011A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 8448300 sectors (4325 MB), CHS=8940/15/63, UDMA(33)
hda: cache flushes not supported
 /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
hdb: max request size: 128KiB
hdb: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(100)
hdb: cache flushes not supported
 /dev/ide/host0/bus0/target1/lun0: p1 p2 < p5 >
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
swsusp: Suspend partition has wrong signature?
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
input: AT Translated Set 2 keyboard on isa0060/serio0
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: Using r5 hash to sort names
Freeing unused kernel memory: 248k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
PCI: Found IRQ 5 for device 0000:00:1f.2
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: Intel Corporation 82801BA/BAM USB (Hub #1)
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 5, io base 0x0000a400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 9 for device 0000:00:1f.4
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: Intel Corporation 82801BA/BAM USB (Hub #2)
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1f.4: irq 9, io base 0x0000a000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Adding 1140572k swap on /dev/hda5.  Priority:-1 extents:1
hw_random hardware driver 1.0.0 loaded
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i815 Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
loop: loaded (max 8 devices)
PCI: Enabling device 0000:01:02.0 (0014 -> 0017)
PCI: IRQ 0 for device 0000:01:02.0 doesn't match PIRQ mask - try pci=usepirqmask
PCI: setting IRQ 11 as level-triggered
PCI: Assigned IRQ 11 for device 0000:01:02.0
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:01:02.0: 3Com PCI 3c905C Tornado at 0xd800. Vers LK1.1.19
ip_conntrack version 2.1 (1527 buckets, 12216 max) - 252 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET: Registered protocol family 17
PCI: Found IRQ 11 for device 0000:01:02.0
PCI: Found IRQ 10 for device 0000:00:1f.5
PCI: Sharing IRQ 10 with 0000:00:1f.3
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49516 usecs
intel8x0: clocking to 48000
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0387d80(lo)
IPv6 over IPv4 tunneling driver
Disabled Privacy Extensions on device caef1c00(sit0)
eth0: no IPv6 routers present



Modprobe says no such module, of course...
FATAL: Module sata_promise not found.


^ permalink raw reply	[flat|nested] 22+ messages in thread
* TX4000 RAID and sata_promise
@ 2005-06-19 12:20 Yuri Kirsanov
  0 siblings, 0 replies; 22+ messages in thread
From: Yuri Kirsanov @ 2005-06-19 12:20 UTC (permalink / raw)
  To: linux-ide

TX4000 RAID and sata_promise.

Good day. I have Mandrake Linux LE2005 with custom kernel
2.6.12.2+Reiser4 patch+TX4000 patch
(First part of this patch http://www.mail-archive.com/linux-ide@vger.kernel.org/msg00150.html
second part failed and I can't figure out how to apply it). When i do
'modprobe sata_promise' it only says:

Aug 14 19:24:21 mandr kernel: libata version 1.11 loaded.
Aug 14 19:24:21 mandr kernel: sata_promise version 1.01
Aug 14 19:24:21 mandr kernel: PCI: Found IRQ 9 for device 0000:01:09.0
Aug 14 19:24:21 mandr kernel: ata1: PATA max UDMA/133 cmd 0xC89FE200 ctl 0xC89FE238 bmdma 0x0 irq 9
Aug 14 19:24:21 mandr kernel: ata2: PATA max UDMA/133 cmd 0xC89FE280 ctl 0xC89FE2B8 bmdma 0x0 irq 9
Aug 14 19:24:21 mandr kernel: ata3: PATA max UDMA/133 cmd 0xC89FE300 ctl 0xC89FE338 bmdma 0x0 irq 9
Aug 14 19:24:21 mandr kernel: ata4: PATA max UDMA/133 cmd 0xC89FE380 ctl 0xC89FE3B8 bmdma 0x0 irq 9
Aug 14 19:24:21 mandr kernel: ata1: no device found (phy stat 00000000)
Aug 14 19:24:21 mandr kernel: scsi0 : sata_promise
Aug 14 19:24:21 mandr kernel: ata2: no device found (phy stat 00000000)
Aug 14 19:24:21 mandr kernel: scsi1 : sata_promise
Aug 14 19:24:21 mandr kernel: ata3: no device found (phy stat 00000000)
Aug 14 19:24:21 mandr kernel: scsi2 : sata_promise
Aug 14 19:24:22 mandr kernel: ata4: no device found (phy stat 00000000)
Aug 14 19:24:22 mandr kernel: scsi3 : sata_promise

I have 2 hard drives connected to TX4000 on IDE1 channel, in stripe
mode. I've set up raid in TX4000 BIOS, but in Linux it can't see my
hard disks, and so I have no /dev/sd* and can't mount this hard
disks...Could you please help me, what am I doing wrong?
I've already tried to install sata_promise both as a module and as a
built-in...I've tried to do 'modprobe sd_mod' first, it only says
'SCSI system initialized'. I'm completely stuck with it :(

PS. I have ASUS i815 CUSL2-M motherboard.


^ permalink raw reply	[flat|nested] 22+ messages in thread
end of thread, other threads:[~2005-08-29  8:58 UTC | newest]

Thread overview: 22+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-08-16  5:30 TX4000 RAID and sata_promise Yuri Kirsanov
2005-08-16 13:10 ` Tyler
2005-08-16 13:30   ` Erik Slagter
2005-08-16 13:35     ` Yuri Kirsanov
2005-08-16 13:50       ` Erik Slagter
2005-08-16 13:54         ` Yuri Kirsanov
     [not found]           ` <1124200516.5550.77.camel@localhost.localdomain>
     [not found]             ` <017501c5a26a$bb31bfc0$6f0aa8c0@rgkb.local>
     [not found]               ` <1124202300.19419.0.camel@localhost.localdomain>
2005-06-21 16:38                 ` Re[2]: " Yuri Kirsanov
     [not found]                   ` <1124211467.19419.24.camel@localhost.localdomain>
2005-06-21 17:47                     ` Re[4]: " Yuri Kirsanov
2005-08-16 18:09                       ` Erik Slagter
2005-06-21 18:19                         ` Re[6]: " Yuri Kirsanov
2005-06-21 18:24                         ` Yuri Kirsanov
  -- strict thread matches above, loose matches on Subject: below --
2005-08-28 17:08 Yuri Kirsanov
2005-08-29  8:57 ` Erik Slagter
2005-08-28 14:46 Yuri Kirsanov
2005-08-28 13:33 Yuri Kirsanov
2005-08-29  8:52 ` Erik Slagter
2005-08-23  8:08 Yuri Kirsanov
2005-08-22  6:28 Allen Bolderoff
2005-08-20  8:46 Yuri Kirsanov
2005-06-23 17:05 Yuri Kirsanov
2005-08-18 17:11 ` Erik Slagter
2005-06-19 12:20 Yuri Kirsanov

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).