Problems with Promise SATAII TX4

linux-ide.vger.kernel.org archive mirror
 help / color / mirror / Atom feed

* Problems with Promise SATAII TX4
@ 2005-03-30  0:10 Kim Roland Rasmussen
  2005-03-31 20:34 ` Joe Harvell
  2005-08-18  3:46 ` Fabian Knittel
  0 siblings, 2 replies; 8+ messages in thread
From: Kim Roland Rasmussen @ 2005-03-30  0:10 UTC (permalink / raw)
  To: linux-ide

Hi all,

Together with a couple of others I have been bitten by problems with the
Promise SATAII TX4 controller.

Common to all is that at some point the kernel log contains the "irq
<SOME NUMBER>: nobody cared!" error message, followed by a call/stack
trace. This is quickly followed up by a "Disabling IRQ #<SOME NUMBER>"
which effectively kills the SATA controller and access to the disks.

Although a somewhat unusual request, could I ask somebody to look at
this

    http://forums.gentoo.org/viewtopic-p-2247734.html

developing thread in the Gentoo Forums. There's simply to much
information there to repost here.

In my case (posted under <rasmussen>) I temporarily seem to have gotten
around it by replacing a driver with another of a different brand.
However, this is not the case for others.

Any idea of what's going on? To me it looks like some interrupt isn't
cleared or something like that (but I'm just guessing).

Cheers,
  Kim

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: Problems with Promise SATAII TX4
  2005-03-30  0:10 Problems with Promise SATAII TX4 Kim Roland Rasmussen
@ 2005-03-31 20:34 ` Joe Harvell
  2005-08-18  3:46 ` Fabian Knittel
  1 sibling, 0 replies; 8+ messages in thread
From: Joe Harvell @ 2005-03-31 20:34 UTC (permalink / raw)
  To: linux-ide

Earlier this month I repeatedly reported a data corruption issue (with
no trap) with the sata_promise support for this card, but got no
response whatsoever from the driver author.

I was able to work around this problem only by using Promise's driver,
but I had to revert from the 2.6 to 2.4 kernel.

Kim Roland Rasmussen wrote:

>Hi all,
>
>Together with a couple of others I have been bitten by problems with the
>Promise SATAII TX4 controller.
>
>Common to all is that at some point the kernel log contains the "irq
><SOME NUMBER>: nobody cared!" error message, followed by a call/stack
>trace. This is quickly followed up by a "Disabling IRQ #<SOME NUMBER>"
>which effectively kills the SATA controller and access to the disks.
>
>Although a somewhat unusual request, could I ask somebody to look at
>this
>
>    http://forums.gentoo.org/viewtopic-p-2247734.html
>
>developing thread in the Gentoo Forums. There's simply to much
>information there to repost here.
>
>In my case (posted under <rasmussen>) I temporarily seem to have gotten
>around it by replacing a driver with another of a different brand.
>However, this is not the case for others.
>
>Any idea of what's going on? To me it looks like some interrupt isn't
>cleared or something like that (but I'm just guessing).
>
>Cheers,
>  Kim
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-ide" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>
>  
>




^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: Problems with Promise SATAII TX4
  2005-03-30  0:10 Problems with Promise SATAII TX4 Kim Roland Rasmussen
  2005-03-31 20:34 ` Joe Harvell
@ 2005-08-18  3:46 ` Fabian Knittel
  2005-08-23 12:58   ` Fabian Knittel
  1 sibling, 1 reply; 8+ messages in thread
From: Fabian Knittel @ 2005-08-18  3:46 UTC (permalink / raw)
  To: linux-ide

[-- Attachment #1: Type: text/plain, Size: 4191 bytes --]

Hi,

I'm experiencing problems with my Promise SATAII TX4 controller, quite
similar to what Kim reported a few months ago.

Using a fresh linux-2.6.12.5 upstream kernel to boot into a rescue shell
(so there's no distribution specific stuff going on, nothing else
loaded, etc.), I can access my three connected Maxtor 120GB drives just
fine, as long as I do so individually.

   e.g.
   $ dd if=/dev/sda of=/dev/null
   $ dd if=/dev/sdb of=/dev/null
   $ dd if=/dev/sdc of=/dev/null

Accessing 2 drives concurrently

   e.g.
   $ dd if=/dev/sda of=/dev/null &
   $ dd if=/dev/sdb of=/dev/null &

is fine too, but as soon as I concurrently start accessing a third drive
as well (in whatever order, it's not specific to sdc), the system starts
to get in serious trouble:

Either immediately or after just a few seconds, I can hear some kind of
"clonk" sound (I've physically disconnected all other drives, so it's
probably one/some/all of the drives) and just after that, the kernel
dumps something like this:

irq 4: nobody cared!
[<c01033e6>] dump_stack+0x17/0x19
[<c012df23>] __report_bad_irq+0x27/0x83
[<c012dfff>] note_interrupt+0x5d/0x7e
[<c012dbbf>] __do_IRQ+0xbf/0xd0
[<c01046f0>] do_IRQ+0x1c/0x28
[<c0102f22>] common_interrupt+0x1a/0x20
[<c0117729>] do_softirq+0x2a/0x2c
[<c01046f5>] do_IRQ+0x21/0x28
[<c0102f22>] common_interrupt+0x1a/0x20
handlers:
[<c024a068>] (pdc_interrupt+0x0/0x15c)
Disabling IRQ #4

and, naturally, everything starts falling apart shortly afterwards:

ata2: command timeout
ATA: abnormal status 0xFF on port 0xE080029C
ata2: status=0xff { Busy }
SCSI error: <1 0 0 0> return code = 0x8000002
sdb: Current: sense key=0xb
    ASC=0x47 ASCQ=0x0
end_request: I/O error, dev sdb, sector 1297600
Buffer I/O error on device sdb, logical block 162200
ata4: command timeout
ata4: status=0x51 { DriveReady SeekComplete Error }
ata4: called with no error (51)!
SCSI error : <3 0 0 0> return code = 0x8000002
sdc: Current: sense key=0x3
[...]

I've attached my configuration file, the lspci -vv output and
/proc/interrupts as well as /proc/scsi/scsi output (the latter three
were produced running my regular debian 2.6.12-1-686 kernel though).


I'm not sure what causes the problems, as I definitely had success
synchronising my RAID5 array at the very beginning of the installation
of this card (~01.08.2005) and the first breakage surfaced almost two
weeks later during the nightly backup (lots of read traffic -> interrupt
disabled -> RAID broken/disabled -> system hang).

So, what I'm probably trying to say is, I don't know whether this
couldn't be some kind of hardware problem instead. Originally I was
using a SiI based controller, which apparently caused the connected
drives to rapidly develop bad sectors (in 4 cases they remained broken
during an analysis from another system and in 1 case it was somehow
specific to the SiI controllers "view" of the drive *shrug*).

Or maybe I was just very lucky and the bug was there all the time.


Now, if you have any idea what I could do/test/install/send you to clear
this up or fix the bug, please tell me! I'd really appreciate any kind
of help on this.

Thanks, Fabian


Some time ago, Kim Roland Rasmussen wrote:
> Hi all,
> 
> Together with a couple of others I have been bitten by problems with the
> Promise SATAII TX4 controller.
> 
> Common to all is that at some point the kernel log contains the "irq
> <SOME NUMBER>: nobody cared!" error message, followed by a call/stack
> trace. This is quickly followed up by a "Disabling IRQ #<SOME NUMBER>"
> which effectively kills the SATA controller and access to the disks.
> 
> Although a somewhat unusual request, could I ask somebody to look at
> this
> 
>     http://forums.gentoo.org/viewtopic-p-2247734.html
> 
> developing thread in the Gentoo Forums. There's simply to much
> information there to repost here.
> 
> In my case (posted under <rasmussen>) I temporarily seem to have gotten
> around it by replacing a driver with another of a different brand.
> However, this is not the case for others.
> 
> Any idea of what's going on? To me it looks like some interrupt isn't
> cleared or something like that (but I'm just guessing).
> 
> Cheers,
>   Kim

[-- Attachment #2: .config --]
[-- Type: text/plain, Size: 28639 bytes --]

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.12.5custom.am-s1.01
# Wed Aug 17 23:41:13 2005
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32

#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
CONFIG_SYSCTL=y
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y

#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
CONFIG_MPENTIUM4=y
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_HPET_TIMER=y
# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
CONFIG_X86_MCE_P4THERMAL=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_X86_REBOOTFIXUPS is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
CONFIG_X86_CPUID=m

#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
CONFIG_REGPARM=y
CONFIG_SECCOMP=y

#
# Power management options (ACPI, APM)
#
# CONFIG_PM is not set

#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_AC=y
# CONFIG_ACPI_BATTERY is not set
# CONFIG_ACPI_BUTTON is not set
# CONFIG_ACPI_VIDEO is not set
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_IBM is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_BUS=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
# CONFIG_X86_PM_TIMER is not set
# CONFIG_ACPI_CONTAINER is not set

#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set

#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
# CONFIG_PCIEPORTBUS is not set
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_LEGACY_PROC is not set
CONFIG_PCI_NAMES=y
# CONFIG_PCI_DEBUG is not set
CONFIG_ISA_DMA_API=y
CONFIG_ISA=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set

#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set

#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set

#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_AOUT is not set
CONFIG_BINFMT_MISC=m

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_DEBUG_DRIVER is not set

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
# CONFIG_PARPORT is not set

#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
# CONFIG_ISAPNP is not set
# CONFIG_PNPBIOS is not set
CONFIG_PNPACPI=y

#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_DEV_XD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_LBD is not set
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_ATA_OVER_ETH is not set

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=y

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
CONFIG_SCSI_LOGGING=y

#
# SCSI Transport Attributes
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set

#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
CONFIG_SCSI_SATA=y
# CONFIG_SCSI_SATA_AHCI is not set
# CONFIG_SCSI_SATA_SVW is not set
# CONFIG_SCSI_ATA_PIIX is not set
# CONFIG_SCSI_SATA_NV is not set
CONFIG_SCSI_SATA_PROMISE=y
# CONFIG_SCSI_SATA_QSTOR is not set
# CONFIG_SCSI_SATA_SX4 is not set
# CONFIG_SCSI_SATA_SIL is not set
# CONFIG_SCSI_SATA_SIS is not set
# CONFIG_SCSI_SATA_ULI is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set

#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set

#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=y
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
CONFIG_MD_RAID10=y
CONFIG_MD_RAID5=y
CONFIG_MD_RAID6=y
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=y
CONFIG_DM_CRYPT=y
CONFIG_DM_SNAPSHOT=y
CONFIG_DM_MIRROR=y
# CONFIG_DM_ZERO is not set
# CONFIG_DM_MULTIPATH is not set

#
# Fusion MPT device support
#
# CONFIG_FUSION is not set

#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set

#
# I2O device support
#
# CONFIG_I2O is not set

#
# Networking support
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_MULTIPATH=y
# CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
CONFIG_INET_TUNNEL=m
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set

#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set

#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_CT_ACCT=y
CONFIG_IP_NF_CONNTRACK_MARK=y
CONFIG_IP_NF_CT_PROTO_SCTP=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_REALM=m
CONFIG_IP_NF_MATCH_SCTP=m
CONFIG_IP_NF_MATCH_COMMENT=m
CONFIG_IP_NF_MATCH_CONNMARK=m
CONFIG_IP_NF_MATCH_HASHLIMIT=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
# CONFIG_IP_NF_NAT_SNMP_BASIC is not set
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_CLASSIFY=m
CONFIG_IP_NF_TARGET_CONNMARK=m
# CONFIG_IP_NF_TARGET_CLUSTERIP is not set
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_TARGET_NOTRACK=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set

#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set

#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_CLK_JIFFIES=y
# CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set
# CONFIG_NET_SCH_CLK_CPU is not set
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m
CONFIG_NET_QOS=y
CONFIG_NET_ESTIMATOR=y
# CONFIG_NET_CLS is not set
CONFIG_NET_CLS_ROUTE=y

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_NET_SB1000 is not set

#
# ARCnet devices
#
# CONFIG_ARCNET is not set

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
CONFIG_NET_VENDOR_3COM=y
# CONFIG_EL1 is not set
# CONFIG_EL2 is not set
# CONFIG_ELPLUS is not set
# CONFIG_EL16 is not set
# CONFIG_EL3 is not set
# CONFIG_3C515 is not set
CONFIG_VORTEX=m
# CONFIG_TYPHOON is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set

#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
# CONFIG_CS89x0 is not set
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
CONFIG_8139TOO=m
CONFIG_8139TOO_PIO=y
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_NET_POCKET is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set

#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set

#
# Token Ring devices
#
# CONFIG_TR is not set

#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set

#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
# CONFIG_PPP_FILTER is not set
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
# CONFIG_PPPOE is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
CONFIG_SHAPER=m
# CONFIG_NETCONSOLE is not set

#
# ISDN subsystem
#
CONFIG_ISDN=m

#
# Old ISDN4Linux
#
# CONFIG_ISDN_I4L is not set

#
# CAPI subsystem
#
CONFIG_ISDN_CAPI=m
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
CONFIG_ISDN_CAPI_MIDDLEWARE=y
CONFIG_ISDN_CAPI_CAPI20=m
CONFIG_ISDN_CAPI_CAPIFS_BOOL=y
CONFIG_ISDN_CAPI_CAPIFS=m

#
# CAPI hardware drivers
#

#
# Active AVM cards
#
# CONFIG_CAPI_AVM is not set

#
# Active Eicon DIVA Server cards
#
# CONFIG_CAPI_EICON is not set

#
# Modular ISDN driver
#
CONFIG_MISDN_DRV=m
# CONFIG_MISDN_MEMDEBUG is not set
# CONFIG_MISDN_AVM_FRITZ is not set
CONFIG_MISDN_HFCPCI=y
# CONFIG_MISDN_HFCMULTI is not set
# CONFIG_MISDN_HFCUSB is not set
# CONFIG_MISDN_SPEEDFAX is not set
# CONFIG_MISDN_W6692 is not set
# CONFIG_MISDN_DSP is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
# CONFIG_SERIAL_8250_ACPI is not set
CONFIG_SERIAL_8250_NR_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256

#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
CONFIG_RTC=m
# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set

#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
# CONFIG_AGP is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_HPET=y
CONFIG_HPET_RTC_IRQ=y
CONFIG_HPET_MMAP=y
# CONFIG_HANGCHECK_TIMER is not set

#
# TPM devices
#
# CONFIG_TCG_TPM is not set

#
# I2C support
#
# CONFIG_I2C is not set

#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set

#
# Misc devices
#
# CONFIG_IBM_ASM is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set

#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set

#
# Graphics support
#
# CONFIG_FB is not set
# CONFIG_VIDEO_SELECT is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y

#
# Sound
#
# CONFIG_SOUND is not set

#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
# CONFIG_USB_EHCI_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
CONFIG_USB_UHCI_HCD=m
# CONFIG_USB_SL811_HCD is not set

#
# USB Device Class drivers
#
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=m

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
#
# CONFIG_USB_STORAGE is not set

#
# USB Input Devices
#
# CONFIG_USB_HID is not set

#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set

#
# Video4Linux support is needed for USB Multimedia device support
#

#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_MON is not set

#
# USB port drivers
#

#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_TEST is not set

#
# USB ATM/DSL drivers
#

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# MMC/SD Card support
#
# CONFIG_MMC is not set

#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
# CONFIG_REISERFS_FS_SECURITY is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y

#
# XFS support
#
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_QUOTA=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=850
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-15"
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
# CONFIG_DEVFS_FS is not set
CONFIG_DEVPTS_FS_XATTR=y
# CONFIG_DEVPTS_FS_SECURITY is not set
CONFIG_TMPFS=y
CONFIG_TMPFS_XATTR=y
# CONFIG_TMPFS_SECURITY is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_RPCSEC_GSS_KRB5=m
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_EFI_PARTITION is not set

#
# Native Language Support
#
CONFIG_NLS=m
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=m
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=m
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=m

#
# Profiling support
#
# CONFIG_PROFILING is not set

#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_LOG_BUF_SHIFT=15
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
CONFIG_FRAME_POINTER=y
CONFIG_EARLY_PRINTK=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_KPROBES is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_4KSTACKS is not set
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set

#
# Cryptographic options
#
CONFIG_CRYPTO=y
# CONFIG_CRYPTO_HMAC is not set
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES_586=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
# CONFIG_CRYPTO_TEST is not set

#
# Hardware crypto devices
#
# CONFIG_CRYPTO_DEV_PADLOCK is not set

#
# Library routines
#
CONFIG_CRC_CCITT=m
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_PC=y

[-- Attachment #3: lspci-vv --]
[-- Type: text/plain, Size: 7580 bytes --]

0000:00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 03)
	Subsystem: Asustek Computer, Inc.: Unknown device 8070
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [e4] #09 [0104]
	Capabilities: [a0] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

0000:00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 03) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: f4000000-f5dfffff
	Prefetchable memory behind bridge: f5f00000-f7ffffff
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-

0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 12) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
	I/O behind bridge: 0000b000-0000dfff
	Memory behind bridge: f1800000-f3ffffff
	Prefetchable memory behind bridge: f5e00000-f5efffff
	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

0000:00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 12)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

0000:00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 12) (prog-if 80 [Master])
	Subsystem: Asustek Computer, Inc.: Unknown device 8028
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Region 4: I/O ports at a800 [size=16]

0000:00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 12) (prog-if 00 [UHCI])
	Subsystem: Asustek Computer, Inc.: Unknown device 8028
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin D routed to IRQ 10
	Region 4: I/O ports at a400 [size=32]

0000:00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 12)
	Subsystem: Asustek Computer, Inc.: Unknown device 8028
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin B routed to IRQ 0
	Region 4: I/O ports at e800 [size=16]

0000:00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 12) (prog-if 00 [UHCI])
	Subsystem: Asustek Computer, Inc.: Unknown device 8028
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin C routed to IRQ 3
	Region 4: I/O ports at a000 [size=32]

0000:01:00.0 VGA compatible controller: nVidia Corporation NV5 [RIVA TNT2/TNT2 Pro] (rev 11) (prog-if 00 [VGA])
	Subsystem: Elsa AG: Unknown device 0c28
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (1250ns min, 250ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at f6000000 (32-bit, prefetchable) [size=32M]
	Expansion ROM at f5ff0000 [disabled] [size=64K]
	Capabilities: [60] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [44] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

0000:02:0a.0 Unknown mass storage controller: Promise Technology, Inc.: Unknown device 3d18 (rev 02)
	Subsystem: Promise Technology, Inc.: Unknown device 3d18
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 72 (1000ns min, 4500ns max), Cache Line Size: 0x01 (4 bytes)
	Interrupt: pin A routed to IRQ 4
	Region 0: I/O ports at d800 [size=128]
	Region 2: I/O ports at d400 [size=256]
	Region 3: Memory at f3800000 (32-bit, non-prefetchable) [size=4K]
	Region 4: Memory at f3000000 (32-bit, non-prefetchable) [size=128K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
	Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 3
	Region 0: I/O ports at d000 [size=128]
	Region 1: Memory at f2800000 (32-bit, non-prefetchable) [size=128]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
	Subsystem: Accton Technology Corporation FNC-0107TX
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: I/O ports at b800 [size=256]
	Region 1: Memory at f2000000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02)
	Subsystem: Cologne Chip Designs GmbH ISDN Board
	Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 16 (4000ns max)
	Interrupt: pin A routed to IRQ 0
	Region 0: I/O ports at b400 [disabled] [size=8]
	Region 1: Memory at f1800000 (32-bit, non-prefetchable) [disabled] [size=256]
	Capabilities: [40] Power Management version 1
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-


[-- Attachment #4: interrupts --]
[-- Type: text/plain, Size: 461 bytes --]

           CPU0       
  0:    7926483          XT-PIC  timer
  1:        473          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  3:     340074          XT-PIC  uhci_hcd:usb2, eth0
  4:     351362          XT-PIC  libata
  5:      25898          XT-PIC  eth1
  8:          1          XT-PIC  rtc
 10:         48          XT-PIC  uhci_hcd:usb1
 14:      15777          XT-PIC  ide0
NMI:          0 
LOC:    7926575 
ERR:          1
MIS:          0

[-- Attachment #5: proc_scsi_scsi --]
[-- Type: text/plain, Size: 492 bytes --]

Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
  Vendor: ATA      Model: Maxtor 6Y120M0   Rev: YAR5
  Type:   Direct-Access                    ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 00
  Vendor: ATA      Model: Maxtor 6Y120M0   Rev: YAR5
  Type:   Direct-Access                    ANSI SCSI revision: 05
Host: scsi3 Channel: 00 Id: 00 Lun: 00
  Vendor: ATA      Model: Maxtor 6Y120M0   Rev: YAR5
  Type:   Direct-Access                    ANSI SCSI revision: 05

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: Problems with Promise SATAII TX4
  2005-08-18  3:46 ` Fabian Knittel
@ 2005-08-23 12:58   ` Fabian Knittel
  2005-10-08 13:12     ` Fabian Knittel
  0 siblings, 1 reply; 8+ messages in thread
From: Fabian Knittel @ 2005-08-23 12:58 UTC (permalink / raw)
  To: linux-ide

Hi,

I wrote:
> I'm experiencing problems with my Promise SATAII TX4 controller, quite
> similar to what Kim reported a few months ago.
> 
> Using a fresh linux-2.6.12.5 upstream kernel to boot into a rescue shell
> (so there's no distribution specific stuff going on, nothing else
> loaded, etc.), I can access my three connected Maxtor 120GB drives just
> fine, as long as I do so individually.
[...]
>>Attached devices:
>>Host: scsi0 Channel: 00 Id: 00 Lun: 00
>>  Vendor: ATA      Model: Maxtor 6Y120M0   Rev: YAR5
>>  Type:   Direct-Access                    ANSI SCSI revision: 05
>>Host: scsi1 Channel: 00 Id: 00 Lun: 00
>>  Vendor: ATA      Model: Maxtor 6Y120M0   Rev: YAR5
>>  Type:   Direct-Access                    ANSI SCSI revision: 05
>>Host: scsi3 Channel: 00 Id: 00 Lun: 00
>>  Vendor: ATA      Model: Maxtor 6Y120M0   Rev: YAR5
>>  Type:   Direct-Access                    ANSI SCSI revision: 05

OK, apparently it's somewhat hardware related after all. I've added a
Seagate drive (Model: ST3120827AS, Rev: 3.42) and reading from this
drive together with two of the Maxtor drives (any two of the three)
currently works without problems (for now).

Switching ports and cables doesn't change anything, so it's not related
to that.

But how can that be? The individual drives don't reveal any problems and
(as reported in my previous mail) the drives worked seamlessly for a few
weeks ...

I'll have to do some more testing and this is probably off-topic by now,
so I'll stop with the noise now.

Fabian

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: Problems with Promise SATAII TX4
  2005-08-23 12:58   ` Fabian Knittel
@ 2005-10-08 13:12     ` Fabian Knittel
  2005-10-08 17:06       ` Mark Hahn
  2005-10-10 10:23       ` Erik Slagter
  0 siblings, 2 replies; 8+ messages in thread
From: Fabian Knittel @ 2005-10-08 13:12 UTC (permalink / raw)
  To: linux-ide

Hi again,

to follow up on myself again and just for the record, the problems
("nobody cared, disabling" interrupt errors while accessing several
drives simultaneously on the same Promise SATAII TX4 controller)
disappeared after hanging all drives on a seperate power supply unit. So
now I'm happily running with a 430W PSU powering the system and a ~200W
PSU powering the 4 drives.

I'm not sure why the system needs more than 430W, but with the new
setup, I can read from 4 drives at once without any problems. Before
this box was converted into a server we probably never tried to access
several drives simultaneously, so I can't really blame anything in specific.

So, my thanks primarily go to Andrey Melnikoff for the right hint (in
private mail). Thanks a lot!

Fabian

For reference, this is what I wrote some time ago:
> I wrote:
>>I'm experiencing problems with my Promise SATAII TX4 controller, quite
>>similar to what Kim reported a few months ago.
>>
>>Using a fresh linux-2.6.12.5 upstream kernel to boot into a rescue shell
>>(so there's no distribution specific stuff going on, nothing else
>>loaded, etc.), I can access my three connected Maxtor 120GB drives just
>>fine, as long as I do so individually.
> 
> [...]
> 
>>>Attached devices:
>>>Host: scsi0 Channel: 00 Id: 00 Lun: 00
>>> Vendor: ATA      Model: Maxtor 6Y120M0   Rev: YAR5
>>> Type:   Direct-Access                    ANSI SCSI revision: 05
>>>Host: scsi1 Channel: 00 Id: 00 Lun: 00
>>> Vendor: ATA      Model: Maxtor 6Y120M0   Rev: YAR5
>>> Type:   Direct-Access                    ANSI SCSI revision: 05
>>>Host: scsi3 Channel: 00 Id: 00 Lun: 00
>>> Vendor: ATA      Model: Maxtor 6Y120M0   Rev: YAR5
>>> Type:   Direct-Access                    ANSI SCSI revision: 05
> 
> 
> OK, apparently it's somewhat hardware related after all. I've added a
> Seagate drive (Model: ST3120827AS, Rev: 3.42) and reading from this
> drive together with two of the Maxtor drives (any two of the three)
> currently works without problems (for now).
> 
> Switching ports and cables doesn't change anything, so it's not related
> to that.
> 
> But how can that be? The individual drives don't reveal any problems and
> (as reported in my previous mail) the drives worked seamlessly for a few
> weeks ...
> 
> I'll have to do some more testing and this is probably off-topic by now,
> so I'll stop with the noise now.

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: Problems with Promise SATAII TX4
  2005-10-08 13:12     ` Fabian Knittel
@ 2005-10-08 17:06       ` Mark Hahn
  2005-10-10 10:29         ` Erik Slagter
  2005-10-10 10:23       ` Erik Slagter
  1 sibling, 1 reply; 8+ messages in thread
From: Mark Hahn @ 2005-10-08 17:06 UTC (permalink / raw)
  To: linux-ide

> I'm not sure why the system needs more than 430W, but with the new

unfortunately, total watts is inadequate for characterizing a PSU.
it's about like classifying cars by how tall they are.

in particular, many non-server higher-watt PSU's are designed to provide
extra power for systems which consume power mainly on the CPU/video voltages,
and may not provide enough power for disks.  further, modern motherboards
have voltage converters for the CPU and video which are less sensitive 
to power quality, and will thus "brownout" some power buses.  after all, 
a typical CPU wants 1.5V or so at an obscene current.  disk electronics, 
as far as I have seen, tend to treat their supply as clean and regulated.

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: Problems with Promise SATAII TX4
  2005-10-08 17:06       ` Mark Hahn
@ 2005-10-10 10:29         ` Erik Slagter
  0 siblings, 0 replies; 8+ messages in thread
From: Erik Slagter @ 2005-10-10 10:29 UTC (permalink / raw)
  To: Mark Hahn; +Cc: linux-ide

[-- Attachment #1: Type: text/plain, Size: 1226 bytes --]

On Sat, 2005-10-08 at 13:06 -0400, Mark Hahn wrote:
> > I'm not sure why the system needs more than 430W, but with the new
> 
> unfortunately, total watts is inadequate for characterizing a PSU.
> it's about like classifying cars by how tall they are.
> 
> in particular, many non-server higher-watt PSU's are designed to provide
> extra power for systems which consume power mainly on the CPU/video voltages,
> and may not provide enough power for disks.  further, modern motherboards
> have voltage converters for the CPU and video which are less sensitive 
> to power quality, and will thus "brownout" some power buses.  after all, 
> a typical CPU wants 1.5V or so at an obscene current.  disk electronics, 
> as far as I have seen, tend to treat their supply as clean and regulated.

BTW my system has a 300W PSU but consumes about 195W according to a
power meter on the primary (230V) side. Which of course is only
comparable up to a certain level.

Also BTW note that besides a total max power, PSU's also have ratings
per voltage and some even per outlet. Maybe that's where the pain comes
from ;-)

A nice "bogus power" error message in the (S)ATA standard would have
been ehrm... beneficial.

[-- Attachment #2: smime.p7s --]
[-- Type: application/x-pkcs7-signature, Size: 2115 bytes --]

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: Problems with Promise SATAII TX4
  2005-10-08 13:12     ` Fabian Knittel
  2005-10-08 17:06       ` Mark Hahn
@ 2005-10-10 10:23       ` Erik Slagter
  1 sibling, 0 replies; 8+ messages in thread
From: Erik Slagter @ 2005-10-10 10:23 UTC (permalink / raw)
  To: Fabian Knittel; +Cc: linux-ide

[-- Attachment #1: Type: text/plain, Size: 1163 bytes --]

On Sat, 2005-10-08 at 15:12 +0200, Fabian Knittel wrote:
> to follow up on myself again and just for the record, the problems
> ("nobody cared, disabling" interrupt errors while accessing several
> drives simultaneously on the same Promise SATAII TX4 controller)
> disappeared after hanging all drives on a seperate power supply unit. So
> now I'm happily running with a 430W PSU powering the system and a ~200W
> PSU powering the 4 drives.
> 
> I'm not sure why the system needs more than 430W, but with the new
> setup, I can read from 4 drives at once without any problems. Before
> this box was converted into a server we probably never tried to access
> several drives simultaneously, so I can't really blame anything in specific.

Interesting, in relation to my setup and problems. I have a 300W PSU
feeding 2/3 (one standby/spun down). It works with harddisk cooling fans
installed (wow... noise!!!) and stops working with the fans removed.

I guess harddisks (and IC's in general) start using more power when
they're hotter)?!

New PSU is underway, including more power (har, har) and better fans.
I'll report when all is installed.

[-- Attachment #2: smime.p7s --]
[-- Type: application/x-pkcs7-signature, Size: 2115 bytes --]

^ permalink raw reply	[flat|nested] 8+ messages in thread

end of thread, other threads:[~2005-10-10 10:30 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-03-30  0:10 Problems with Promise SATAII TX4 Kim Roland Rasmussen
2005-03-31 20:34 ` Joe Harvell
2005-08-18  3:46 ` Fabian Knittel
2005-08-23 12:58   ` Fabian Knittel
2005-10-08 13:12     ` Fabian Knittel
2005-10-08 17:06       ` Mark Hahn
2005-10-10 10:29         ` Erik Slagter
2005-10-10 10:23       ` Erik Slagter

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).