Serious IDE problem still present in 2.6.14

linux-ide.vger.kernel.org archive mirror
 help / color / mirror / Atom feed

* Serious IDE problem still present in 2.6.14
@ 2005-10-30  0:48 David Ronis
  2005-10-30  2:15 ` Stefan
  0 siblings, 1 reply; 13+ messages in thread
From: David Ronis @ 2005-10-30  0:48 UTC (permalink / raw)
  To: linux-ide

The problem I reported on the linux-kernel list and later here.  See

   http://marc.theaimsgroup.com/?l=linux-kernel&m=112802950411697&w=2

with disk access on my HP pavilion is still present.  In short,
something broke in the 2.6.13 series, and it still is broken in 2.6.14.
One thing I hadn't added explicitly to my earlier report, is that this
laptop has a P4 Hyperthreaded chip (someone mentioned that there was an
ACPI problem related to hyperthreading).

David

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-10-30  0:48 Serious IDE problem still present in 2.6.14 David Ronis
@ 2005-10-30  2:15 ` Stefan
  2005-10-30  3:13   ` David Ronis
  0 siblings, 1 reply; 13+ messages in thread
From: Stefan @ 2005-10-30  2:15 UTC (permalink / raw)
  To: David.Ronis; +Cc: linux-ide

David Ronis wrote:

>The problem I reported on the linux-kernel list and later here.  See
>
>   http://marc.theaimsgroup.com/?l=linux-kernel&m=112802950411697&w=2
>  
>
I just read your info there, you did not submit output of:

hdparm /dev/hda though

is using_dma switched on if you look at the output of the above command?

>with disk access on my HP pavilion is still present.  In short,
>something broke in the 2.6.13 series, and it still is broken in 2.6.14.
>One thing I hadn't added explicitly to my earlier report, is that this
>laptop has a P4 Hyperthreaded chip (someone mentioned that there was an
>ACPI problem related to hyperthreading).
>
>David
>
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-ide" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>
>  
>


	

	
		
___________________________________________________________ 
Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-10-30  2:15 ` Stefan
@ 2005-10-30  3:13   ` David Ronis
  2005-10-30  8:53     ` Stefan
  0 siblings, 1 reply; 13+ messages in thread
From: David Ronis @ 2005-10-30  3:13 UTC (permalink / raw)
  To: Stefan; +Cc: David.Ronis, linux-ide

Look at the link, all the information (output from hdparm) is there (and
yes, usingdma is on).

David

On Sun, 2005-10-30 at 03:15 +0100, Stefan wrote:
> http://marc.theaimsgroup.com/?l=linux-kernel&m=112802950411697&w=2


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-10-30  3:13   ` David Ronis
@ 2005-10-30  8:53     ` Stefan
  2005-10-30 15:52       ` David Ronis
  0 siblings, 1 reply; 13+ messages in thread
From: Stefan @ 2005-10-30  8:53 UTC (permalink / raw)
  To: David.Ronis; +Cc: linux-ide

David Ronis wrote:

>Look at the link, all the information (output from hdparm) is there (and
>yes, usingdma is on).
>  
>
Yes I did look at the link, but I only see output from:

hdparm -i /dev/hda

not

hdparm /dev/hda


>David
>
>On Sun, 2005-10-30 at 03:15 +0100, Stefan wrote:
>  
>
>>http://marc.theaimsgroup.com/?l=linux-kernel&m=112802950411697&w=2
>>    
>>
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-ide" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>
>  
>


	

	
		
___________________________________________________________ 
Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-10-30  8:53     ` Stefan
@ 2005-10-30 15:52       ` David Ronis
  0 siblings, 0 replies; 13+ messages in thread
From: David Ronis @ 2005-10-30 15:52 UTC (permalink / raw)
  To: Stefan; +Cc: David.Ronis, linux-ide

Hi Stefan,

Here's the information you wanted (as well as output from several other
hdparm reports/tests).  Note that I run

/sbin/hdparm -qS240 -qc1 -qm16 /dev/hda

from rc.local.  The m16 isn't needed on 2.6.12.6 (it's set anyhow) but
is on 2.6.14.  There's a lot of output.  I diff'ed the two sets and
basically there're identical except for:

bash-3.00# diff hdparmreport.2.6.12.6 hdparmreport.2.6.14
27c27
<  Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:  ATA/ATAPI-1
ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6
---
>  Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2: 
159c159
<  Timing buffered disk reads:  102 MB in  3.05 seconds =  33.48 MB/sec
---
>  Timing buffered disk reads:   66 MB in  3.05 seconds =  21.63 MB/sec
164c164
<  Timing cached reads:   1296 MB in  2.00 seconds = 648.10 MB/sec
---
>  Timing cached reads:    28 MB in  2.08 seconds =  13.46 MB/sec

David

OK, here's the full information:

First on 2.6.12.6:
hdparm /dev/hda

/dev/hda:
 multcount    = 16 (on)
 IO_support   =  1 (32-bit)
 unmaskirq    =  0 (off)
 using_dma    =  1 (on)
 keepsettings =  0 (off)
 readonly     =  0 (off)
 readahead    = 256 (on)
 geometry     = 65535/16/63, sectors = 195371568, start = 0

hdparm -i /dev/hda

/dev/hda:

 Model=ST9100823A, FwRev=3.00, SerialNo=3LG0V6AP
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=195371568
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=yes: unknown setting WriteCache=enabled
 Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:  ATA/ATAPI-1
ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6

 * signifies the current active mode


hdparm -I /dev/hda

/dev/hda:

ATA device, with non-removable media
	Model Number:       ST9100823A                              
	Serial Number:      3LG0V6AP
	Firmware Revision:  3.00    
Standards:
	Used: ATA/ATAPI-6 T13 1410D revision 2 
	Supported: 6 5 4 3 
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:   16514064
	LBA    user addressable sectors:  195371568
	device size with M = 1024*1024:       95396 MBytes
	device size with M = 1000*1000:      100030 MBytes (100 GB)
Capabilities:
	LBA, IORDY(can be disabled)
	bytes avail on r/w long: 4	Queue depth: 1
	Standby timer values: spec'd by Standard, no device specific minimum
	R/W multiple sector transfer: Max = 16	Current = 16
	Advanced power management level: unknown setting (0x8080)
	Recommended acoustic management value: 254, current value: 0
	DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
	Enabled	Supported:
	   *	READ BUFFER cmd
	   *	WRITE BUFFER cmd
	   *	Host Protected Area feature set
	   *	Look-ahead
	   *	Write cache
	   *	Power Management feature set
		Security Mode feature set
	   *	SMART feature set
	   *	Mandatory FLUSH CACHE command 
	   *	Device Configuration Overlay feature set 
		SET MAX security extension
	   *	Advanced Power Management feature set
	   *	DOWNLOAD MICROCODE cmd
	   *	SMART self-test 
	   *	SMART error logging 
Security: 
	Master password revision code = 65534
		supported
	not	enabled
	not	locked
		frozen
	not	expired: security count
	not	supported: enhanced erase
HW reset results:
	CBLID- above Vih
	Device num = 0
Checksum: correct

hdparm -I /dev/hda

/dev/hda:

ATA device, with non-removable media
	Model Number:       ST9100823A                              
	Serial Number:      3LG0V6AP
	Firmware Revision:  3.00    
Standards:
	Used: ATA/ATAPI-6 T13 1410D revision 2 
	Supported: 6 5 4 3 
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:   16514064
	LBA    user addressable sectors:  195371568
	device size with M = 1024*1024:       95396 MBytes
	device size with M = 1000*1000:      100030 MBytes (100 GB)
Capabilities:
	LBA, IORDY(can be disabled)
	bytes avail on r/w long: 4	Queue depth: 1
	Standby timer values: spec'd by Standard, no device specific minimum
	R/W multiple sector transfer: Max = 16	Current = 16
	Advanced power management level: unknown setting (0x8080)
	Recommended acoustic management value: 254, current value: 0
	DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
	Enabled	Supported:
	   *	READ BUFFER cmd
	   *	WRITE BUFFER cmd
	   *	Host Protected Area feature set
	   *	Look-ahead
	   *	Write cache
	   *	Power Management feature set
		Security Mode feature set
	   *	SMART feature set
	   *	Mandatory FLUSH CACHE command 
	   *	Device Configuration Overlay feature set 
		SET MAX security extension
	   *	Advanced Power Management feature set
	   *	DOWNLOAD MICROCODE cmd
	   *	SMART self-test 
	   *	SMART error logging 
Security: 
	Master password revision code = 65534
		supported
	not	enabled
	not	locked
		frozen
	not	expired: security count
	not	supported: enhanced erase
HW reset results:
	CBLID- above Vih
	Device num = 0
Checksum: correct

hdparm -t /dev/hda

/dev/hda:
 Timing buffered disk reads:  102 MB in  3.05 seconds =  33.48 MB/sec

hdparm -T /dev/hda

/dev/hda:
 Timing cached reads:   1296 MB in  2.00 seconds = 648.10 MB/sec

Now on 2.6.14:
hdparm /dev/hda

/dev/hda:
 multcount    = 16 (on)
 IO_support   =  1 (32-bit)
 unmaskirq    =  0 (off)
 using_dma    =  1 (on)
 keepsettings =  0 (off)
 readonly     =  0 (off)
 readahead    = 256 (on)
 geometry     = 65535/16/63, sectors = 195371568, start = 0

hdparm -i /dev/hda

/dev/hda:

 Model=ST9100823A, FwRev=3.00, SerialNo=3LG0V6AP
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=195371568
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=yes: unknown setting WriteCache=enabled
 Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2: 

 * signifies the current active mode


hdparm -I /dev/hda

/dev/hda:

ATA device, with non-removable media
	Model Number:       ST9100823A                              
	Serial Number:      3LG0V6AP
	Firmware Revision:  3.00    
Standards:
	Used: ATA/ATAPI-6 T13 1410D revision 2 
	Supported: 6 5 4 3 
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:   16514064
	LBA    user addressable sectors:  195371568
	device size with M = 1024*1024:       95396 MBytes
	device size with M = 1000*1000:      100030 MBytes (100 GB)
Capabilities:
	LBA, IORDY(can be disabled)
	bytes avail on r/w long: 4	Queue depth: 1
	Standby timer values: spec'd by Standard, no device specific minimum
	R/W multiple sector transfer: Max = 16	Current = 16
	Advanced power management level: unknown setting (0x8080)
	Recommended acoustic management value: 254, current value: 0
	DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
	Enabled	Supported:
	   *	READ BUFFER cmd
	   *	WRITE BUFFER cmd
	   *	Host Protected Area feature set
	   *	Look-ahead
	   *	Write cache
	   *	Power Management feature set
		Security Mode feature set
	   *	SMART feature set
	   *	Mandatory FLUSH CACHE command 
	   *	Device Configuration Overlay feature set 
		SET MAX security extension
	   *	Advanced Power Management feature set
	   *	DOWNLOAD MICROCODE cmd
	   *	SMART self-test 
	   *	SMART error logging 
Security: 
	Master password revision code = 65534
		supported
	not	enabled
	not	locked
		frozen
	not	expired: security count
	not	supported: enhanced erase
HW reset results:
	CBLID- above Vih
	Device num = 0
Checksum: correct

hdparm -I /dev/hda

/dev/hda:

ATA device, with non-removable media
	Model Number:       ST9100823A                              
	Serial Number:      3LG0V6AP
	Firmware Revision:  3.00    
Standards:
	Used: ATA/ATAPI-6 T13 1410D revision 2 
	Supported: 6 5 4 3 
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:   16514064
	LBA    user addressable sectors:  195371568
	device size with M = 1024*1024:       95396 MBytes
	device size with M = 1000*1000:      100030 MBytes (100 GB)
Capabilities:
	LBA, IORDY(can be disabled)
	bytes avail on r/w long: 4	Queue depth: 1
	Standby timer values: spec'd by Standard, no device specific minimum
	R/W multiple sector transfer: Max = 16	Current = 16
	Advanced power management level: unknown setting (0x8080)
	Recommended acoustic management value: 254, current value: 0
	DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
	Enabled	Supported:
	   *	READ BUFFER cmd
	   *	WRITE BUFFER cmd
	   *	Host Protected Area feature set
	   *	Look-ahead
	   *	Write cache
	   *	Power Management feature set
		Security Mode feature set
	   *	SMART feature set
	   *	Mandatory FLUSH CACHE command 
	   *	Device Configuration Overlay feature set 
		SET MAX security extension
	   *	Advanced Power Management feature set
	   *	DOWNLOAD MICROCODE cmd
	   *	SMART self-test 
	   *	SMART error logging 
Security: 
	Master password revision code = 65534
		supported
	not	enabled
	not	locked
		frozen
	not	expired: security count
	not	supported: enhanced erase
HW reset results:
	CBLID- above Vih
	Device num = 0
Checksum: correct

hdparm -t /dev/hda

/dev/hda:
 Timing buffered disk reads:   66 MB in  3.05 seconds =  21.63 MB/sec

hdparm -T /dev/hda

/dev/hda:
 Timing cached reads:    28 MB in  2.08 seconds =  13.46 MB/sec





On Sun, 2005-10-30 at 09:53 +0100, Stefan wrote:
> David Ronis wrote:
> 
> >Look at the link, all the information (output from hdparm) is there (and
> >yes, usingdma is on).
> >  
> >
> Yes I did look at the link, but I only see output from:
> 
> hdparm -i /dev/hda
> 
> not
> 
> hdparm /dev/hda
> 
> 
> >David
> >
> >On Sun, 2005-10-30 at 03:15 +0100, Stefan wrote:
> >  
> >
> >>http://marc.theaimsgroup.com/?l=linux-kernel&m=112802950411697&w=2
> >>    
> >>
> >
> >-
> >To unsubscribe from this list: send the line "unsubscribe linux-ide" in
> >the body of a message to majordomo@vger.kernel.org
> >More majordomo info at  http://vger.kernel.org/majordomo-info.html
> >
> >  
> >
> 
> 
> 	
> 
> 	
> 		
> ___________________________________________________________ 
> Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de
> 


^ permalink raw reply	[flat|nested] 13+ messages in thread

[parent not found: <Pine.LNX.4.44.0510301030120.26176-100000@coffee.psychology.mcmaster.ca>]

* Re: Serious IDE problem still present in 2.6.14
       [not found] <Pine.LNX.4.44.0510301030120.26176-100000@coffee.psychology.mcmaster.ca>
@ 2005-10-30 16:31 ` David Ronis
  2005-10-30 18:57   ` Stefan
  2005-10-30 23:02   ` Stefan
  0 siblings, 2 replies; 13+ messages in thread
From: David Ronis @ 2005-10-30 16:31 UTC (permalink / raw)
  To: Mark Hahn; +Cc: David.Ronis, linux-ide

Hi Mark,

I've copied the information you wanted below.

First in 2.6.12.6:

cat /proc/interrupts
           CPU0       CPU1       
  0:      53375          1    IO-APIC-edge  timer
  1:         47          2    IO-APIC-edge  i8042
  5:          1          0   IO-APIC-level  ATI IXP
  8:          1          0    IO-APIC-edge  rtc
 12:        127          0    IO-APIC-edge  i8042
 14:       4970          0    IO-APIC-edge  ide0
 15:          0          0    IO-APIC-edge  ide1
 16:         28          0   IO-APIC-level  ohci_hcd:usb4, yenta,
ohci1394
 17:          1          0   IO-APIC-level  yenta
 18:          0          0   IO-APIC-level  ohci_hcd:usb5
 19:          2          0   IO-APIC-level  eth0, ehci_hcd:usb1,
ohci_hcd:usb2, ohci_hcd:usb3
 21:         43          0   IO-APIC-level  acpi
NMI:          0          0 
LOC:      53271      53277 
ERR:          0
MIS:          0

lspci -v
00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge
(rev 02)
	Subsystem: ATI Technologies Inc: Unknown device 1234
	Flags: bus master, 66Mhz, medium devsel, latency 64
	Memory at d2000000 (32-bit, prefetchable) [size=32M]
	Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [a0] AGP version 3.0

00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
(prog-if 00 [Normal decode])
	Flags: bus master, 66Mhz, medium devsel, latency 99
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: d0100000-d01fffff
	Prefetchable memory behind bridge: e0000000-efffffff

00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev
01) (prog-if 10 [OHCI])
	Subsystem: ATI Technologies Inc: Unknown device 434c
	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 19
	Memory at d0001000 (32-bit, non-prefetchable) [size=4K]

00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev
01) (prog-if 10 [OHCI])
	Subsystem: ATI Technologies Inc: Unknown device 434c
	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 19
	Memory at d0002000 (32-bit, non-prefetchable) [size=4K]

00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16)
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: 66Mhz, medium devsel
	I/O ports at 8040 [size=16]
	Memory at 58000000 (32-bit, non-prefetchable) [size=1K]

00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master
PCI IDE Controller (prog-if 8a [Master SecP PriP])
	Subsystem: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE
Controller
	Flags: bus master, medium devsel, latency 64, IRQ 16
	I/O ports at <ignored>
	I/O ports at <ignored>
	I/O ports at <ignored>
	I/O ports at <ignored>
	I/O ports at 8060 [size=16]

00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c
	Subsystem: ATI Technologies Inc: Unknown device 434c
	Flags: bus master, 66Mhz, medium devsel, latency 0

00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if
01 [Subtractive decode])
	Flags: bus master, 66Mhz, medium devsel, latency 64
	Bus: primary=00, secondary=02, subordinate=04, sec-latency=69
	I/O behind bridge: 0000a000-0000afff
	Memory behind bridge: d0200000-d02fffff

00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97
Audio Controller
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, 66Mhz, slow devsel, latency 64, IRQ 5
	Memory at d0003000 (32-bit, non-prefetchable) [size=256]

00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00
[Generic])
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: 66Mhz, slow devsel, IRQ 5
	Memory at d0003400 (32-bit, non-prefetchable) [size=256]

01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP
[Radeon Mobility 9100IGP] (prog-if 00 [VGA])
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 66,
IRQ 10
	Memory at e0000000 (32-bit, prefetchable) [size=256M]
	I/O ports at 9000 [size=256]
	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: [58] AGP version 3.0
	Capabilities: [50] Power Management version 2

02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, medium devsel, latency 64, IRQ 16
	Memory at d0208000 (32-bit, non-prefetchable) [size=2K]
	Memory at d0200000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [44] Power Management version 2

02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g
Wireless LAN Controller (rev 03)
	Subsystem: Hewlett-Packard Company: Unknown device 12f4
	Flags: bus master, fast devsel, latency 64, IRQ 5
	Memory at d0204000 (32-bit, non-prefetchable) [size=8K]

02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, medium devsel, latency 128, IRQ 19
	I/O ports at a000 [size=256]
	Memory at d0208800 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2

02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
(rev 01)
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, medium devsel, latency 168, IRQ 17
	Memory at 58001000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
	Memory window 0: 58400000-587ff000 (prefetchable)
	Memory window 1: 58800000-58bff000
	I/O window 0: 00004000-000040ff
	I/O window 1: 00004400-000044ff
	16-bit legacy interface ports at 0001

02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
(rev 01)
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, medium devsel, latency 168, IRQ 16
	Memory at 58002000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
	Memory window 0: 58c00000-58fff000 (prefetchable)
	Memory window 1: 59000000-593ff000
	I/O window 0: 00004800-000048ff
	I/O window 1: 00004c00-00004cff
	16-bit legacy interface ports at 0001

02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading
Function (rev 01)
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, medium devsel, latency 64
	I/O ports at a400 [size=64]
	Capabilities: [44] Power Management version 2

02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
	Subsystem: NEC Corporation USB
	Flags: bus master, medium devsel, latency 64, IRQ 16
	Memory at d0206000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [40] Power Management version 2

02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
	Subsystem: NEC Corporation USB
	Flags: bus master, medium devsel, latency 64, IRQ 18
	Memory at d0207000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [40] Power Management version 2

02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20
[EHCI])
	Subsystem: NEC Corporation USB 2.0
	Flags: bus master, medium devsel, latency 64, IRQ 19
	Memory at d0208c00 (32-bit, non-prefetchable) [size=256]
	Capabilities: [40] Power Management version 2


dmesg
Linux version 2.6.12.6 (root@montroll.lan) (gcc version 3.4.4) #4 SMP
Tue Aug 30 20:38:22 EDT 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000047f70000 (usable)
 BIOS-e820: 0000000047f70000 - 0000000047f7d000 (ACPI data)
 BIOS-e820: 0000000047f7d000 - 0000000047f80000 (ACPI NVS)
 BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved)
 BIOS-e820: 0000000057f80000 - 0000000058000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000f6570
On node 0 totalpages: 229376
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6600
ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @
0x47f791c8
ACPI: FADT (v001 HP     Chinook  0x06040000 ATI  0x000f4240) @
0x47f7ceed
ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @
0x47f7cf61
ACPI: SSDT (v001 PTLTD  ACPIHT   0x06040000  LTP 0x00000001) @
0x47f7cfc9
ACPI: DSDT (v001     HP    SB200 0x06040000 INTL 0x20030509) @
0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 58000000 (gap: 58000000:a6c00000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=2.6.12.6 ro root=302
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 3000.728 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 906084k/917504k available (1695k kernel code, 10908k reserved,
737k data, 192k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
Calibrating delay loop... 5963.77 BogoMIPS (lpj=2981888)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay loop... 5996.54 BogoMIPS (lpj=2998272)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
Total of 2 processors activated (11960.32 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
 domain 0: span 3
  groups: 1 2
  domain 1: span 3
   groups: 3
CPU1 attaching sched-domain:
 domain 0: span 3
  groups: 2 1
  domain 1: span 3
   groups: 3
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:05.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled.
ACPI: Embedded Controller [EC0] (gpe 6)
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
report
Machine check exception polling timer started.
Initializing Cryptographic API
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Thermal Zone [THRM] (52 C)
Real Time Clock Driver v1.12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST9100823A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SD-R2512, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63,
UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2
mice: PS/2 mouse device common for all mice
input: PC Speaker
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 15
ACPI wakeup devices: 
ELAN USB0 USB1 USB2 KBC0 MSE0 
ACPI: (supports S0 S3 S4 S5)
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 192k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
alps.c: Enabling hardware tapping
input: PS/2 Mouse on isa0060/serio4
input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
Adding 977216k swap on /dev/hda1.  Priority:-1 extents:1
EXT3 FS on hda2, internal journal
Linux agpgart interface v0.101 (c) Dave Jones
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:01:82:2d, IRQ 19
eth0:  Identified 8139 chip type 'RTL-8101'
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:02:07.2: NEC Corporation USB 2.0
ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:02:07.2: irq 19, io mem 0xd0208c00
ehci_hcd 0000:02:07.2: park 0
ehci_hcd 0000:02:07.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: ATI Technologies Inc OHCI USB Controller #1
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 19, io mem 0xd0001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: ATI Technologies Inc OHCI USB Controller #2
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 19, io mem 0xd0002000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:02:07.0: NEC Corporation USB
ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:02:07.0: irq 16, io mem 0xd0206000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:02:07.1[B] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:02:07.1: NEC Corporation USB (#2)
ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5
ohci_hcd 0000:02:07.1: irq 18, io mem 0xd0207000
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 4-1: new low speed USB device using ohci_hcd and address 2
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 17
Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x0ed8, PCI irq 17
Socket status: 30000006
ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
Yenta: ISA IRQ mask 0x0ed8, PCI irq 16
Socket status: 30000006
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]
MMIO=[d0208000-d02087ff]  Max Packet=[2048]
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing
disabled
ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5
agpgart: Detected Ati IGP9100/M chipset
agpgart: AGP aperture is 32M @ 0xd2000000
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[463f02005c594058]
eth1394: $Rev: 1247 $ Ben Collins <bcollins@debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
USB Universal Host Controller Interface driver v2.2
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (7168 buckets, 57344 max) - 256 bytes per
conntrack
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).

Now in 2.6.14:

cat /proc/interrupts
           CPU0       CPU1       
  0:     345156          3    IO-APIC-edge  timer
  1:         51          2    IO-APIC-edge  i8042
  5:          1          0   IO-APIC-level  ATI IXP
  8:          1          0    IO-APIC-edge  rtc
 12:        121          0    IO-APIC-edge  i8042
 14:       5474          0    IO-APIC-edge  ide0
 15:          0          0    IO-APIC-edge  ide1
 16:          1          0   IO-APIC-level  yenta
 17:         29          0   IO-APIC-level  ohci_hcd:usb4, yenta,
ohci1394
 18:          2          0   IO-APIC-level  eth0, ehci_hcd:usb1,
ohci_hcd:usb2, ohci_hcd:usb3
 19:          0          0   IO-APIC-level  ohci_hcd:usb5
 21:         40          0   IO-APIC-level  acpi
NMI:          0          0 
LOC:     345004     345037 
ERR:          0
MIS:          0

lspci -v
00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge
(rev 02)
	Subsystem: ATI Technologies Inc: Unknown device 1234
	Flags: bus master, 66Mhz, medium devsel, latency 64
	Memory at d2000000 (32-bit, prefetchable) [size=32M]
	Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [a0] AGP version 3.0

00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
(prog-if 00 [Normal decode])
	Flags: bus master, 66Mhz, medium devsel, latency 99
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: d0100000-d01fffff
	Prefetchable memory behind bridge: e0000000-efffffff

00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev
01) (prog-if 10 [OHCI])
	Subsystem: ATI Technologies Inc: Unknown device 434c
	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18
	Memory at d0001000 (32-bit, non-prefetchable) [size=4K]

00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev
01) (prog-if 10 [OHCI])
	Subsystem: ATI Technologies Inc: Unknown device 434c
	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18
	Memory at d0002000 (32-bit, non-prefetchable) [size=4K]

00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16)
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: 66Mhz, medium devsel
	I/O ports at 8040 [size=16]
	Memory at 64000000 (32-bit, non-prefetchable) [size=1K]

00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master
PCI IDE Controller (prog-if 8a [Master SecP PriP])
	Subsystem: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE
Controller
	Flags: bus master, medium devsel, latency 64, IRQ 17
	I/O ports at <ignored>
	I/O ports at <ignored>
	I/O ports at <ignored>
	I/O ports at <ignored>
	I/O ports at 8060 [size=16]

00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c
	Subsystem: ATI Technologies Inc: Unknown device 434c
	Flags: bus master, 66Mhz, medium devsel, latency 0

00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if
01 [Subtractive decode])
	Flags: bus master, 66Mhz, medium devsel, latency 64
	Bus: primary=00, secondary=02, subordinate=04, sec-latency=69
	I/O behind bridge: 0000a000-0000afff
	Memory behind bridge: d0200000-d02fffff
	Prefetchable memory behind bridge: 60000000-63ffffff

00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97
Audio Controller
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, 66Mhz, slow devsel, latency 64, IRQ 5
	Memory at d0003000 (32-bit, non-prefetchable) [size=256]

00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00
[Generic])
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: 66Mhz, slow devsel, IRQ 5
	Memory at d0003400 (32-bit, non-prefetchable) [size=256]

01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP
[Radeon Mobility 9100IGP] (prog-if 00 [VGA])
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 66,
IRQ 10
	Memory at e0000000 (32-bit, prefetchable) [size=256M]
	I/O ports at 9000 [size=256]
	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at d0120000 [disabled] [size=128K]
	Capabilities: [58] AGP version 3.0
	Capabilities: [50] Power Management version 2

02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, medium devsel, latency 64, IRQ 17
	Memory at d0208000 (32-bit, non-prefetchable) [size=2K]
	Memory at d0200000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [44] Power Management version 2

02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g
Wireless LAN Controller (rev 03)
	Subsystem: Hewlett-Packard Company: Unknown device 12f4
	Flags: bus master, fast devsel, latency 64, IRQ 5
	Memory at d0204000 (32-bit, non-prefetchable) [size=8K]

02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, medium devsel, latency 128, IRQ 18
	I/O ports at a000 [size=256]
	Memory at d0208800 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2

02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
(rev 01)
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, medium devsel, latency 168, IRQ 16
	Memory at d0209000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
	Memory window 0: 60000000-61fff000 (prefetchable)
	Memory window 1: 66000000-67fff000
	I/O window 0: 0000a800-0000a8ff
	I/O window 1: 0000ac00-0000acff
	16-bit legacy interface ports at 0001

02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
(rev 01)
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, medium devsel, latency 168, IRQ 17
	Memory at d020a000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
	Memory window 0: 62000000-63fff000 (prefetchable)
	Memory window 1: 68000000-69fff000
	I/O window 0: 00001400-000014ff
	I/O window 1: 00001800-000018ff
	16-bit legacy interface ports at 0001

02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading
Function (rev 01)
	Subsystem: Hewlett-Packard Company: Unknown device 006b
	Flags: bus master, medium devsel, latency 64
	I/O ports at a400 [size=64]
	Capabilities: [44] Power Management version 2

02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
	Subsystem: NEC Corporation USB
	Flags: bus master, medium devsel, latency 64, IRQ 17
	Memory at d0206000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [40] Power Management version 2

02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
	Subsystem: NEC Corporation USB
	Flags: bus master, medium devsel, latency 64, IRQ 19
	Memory at d0207000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [40] Power Management version 2

02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20
[EHCI])
	Subsystem: NEC Corporation USB 2.0
	Flags: bus master, medium devsel, latency 64, IRQ 18
	Memory at d0208c00 (32-bit, non-prefetchable) [size=256]
	Capabilities: [40] Power Management version 2


dmesg
Linux version 2.6.14 (root@montroll) (gcc version 4.0.2) #10 SMP Fri Oct
28 15:56:01 EDT 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000047f70000 (usable)
 BIOS-e820: 0000000047f70000 - 0000000047f7d000 (ACPI data)
 BIOS-e820: 0000000047f7d000 - 0000000047f80000 (ACPI NVS)
 BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved)
 BIOS-e820: 0000000057f80000 - 0000000058000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000f6570
On node 0 totalpages: 229376
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6600
ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @
0x47f791c8
ACPI: FADT (v001 HP     Chinook  0x06040000 ATI  0x000f4240) @
0x47f7ceed
ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @
0x47f7cf61
ACPI: SSDT (v001 PTLTD  ACPIHT   0x06040000  LTP 0x00000001) @
0x47f7cfc9
ACPI: DSDT (v001     HP    SB200 0x06040000 INTL 0x20030509) @
0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 60000000 (gap: 58000000:a6c00000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=2.6.14 ro root=302
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 3000.911 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 906284k/917504k available (1696k kernel code, 10708k reserved,
531k data, 188k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
Calibrating delay using timer specific routine.. 6002.40 BogoMIPS
(lpj=3001201)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5999.46 BogoMIPS
(lpj=2999730)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
Total of 2 processors activated (12001.86 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
softlockup thread 0 started up.
Brought up 2 CPUs
softlockup thread 1 started up.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:05.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled.
ACPI: Embedded Controller [EC0] (gpe 6)
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
report
PCI: Bridge: 0000:00:01.0
  IO window: 9000-9fff
  MEM window: d0100000-d01fffff
  PREFETCH window: e0000000-efffffff
PCI: Bus 3, cardbus bridge: 0000:02:04.0
  IO window: 0000a800-0000a8ff
  IO window: 0000ac00-0000acff
  PREFETCH window: 60000000-61ffffff
  MEM window: 66000000-67ffffff
PCI: Bus 7, cardbus bridge: 0000:02:04.1
  IO window: 00001400-000014ff
  IO window: 00001800-000018ff
  PREFETCH window: 62000000-63ffffff
  MEM window: 68000000-69ffffff
PCI: Bridge: 0000:00:14.4
  IO window: a000-afff
  MEM window: d0200000-d02fffff
  PREFETCH window: 60000000-63ffffff
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 17
Machine check exception polling timer started.
Initializing Cryptographic API
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRM] (52 C)
Real Time Clock Driver v1.12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST9100823A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SD-R2512, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63,
UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2
mice: PS/2 mouse device common for all mice
input: PC Speaker
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 15
Using IPI Shortcut mode
kjournald starting.  Commit interval 5 seconds
input: AT Translated Set 2 keyboard on isa0060/serio0
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 188k freed
input: PS/2 Mouse on isa0060/serio4
input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
Adding 977216k swap on /dev/hda1.  Priority:-1 extents:1 across:977216k
EXT3 FS on hda2, internal journal
Linux agpgart interface v0.101 (c) Dave Jones
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 18
eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:01:82:2d, IRQ 18
eth0:  Identified 8139 chip type 'RTL-8101'
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 18
ehci_hcd 0000:02:07.2: EHCI Host Controller
ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:02:07.2: irq 18, io mem 0xd0208c00
ehci_hcd 0000:02:07.2: park 0
ehci_hcd 0000:02:07.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver
(PCI)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 18, io mem 0xd0001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 18, io mem 0xd0002000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 17
ohci_hcd 0000:02:07.0: OHCI Host Controller
ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:02:07.0: irq 17, io mem 0xd0206000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:02:07.1[B] -> GSI 18 (level, low) -> IRQ 19
ohci_hcd 0000:02:07.1: OHCI Host Controller
ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5
ohci_hcd 0000:02:07.1: irq 19, io mem 0xd0207000
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 4-1: new low speed USB device using ohci_hcd and address 2
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x0ed8, PCI irq 16
Socket status: 30000086
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff
ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 17
Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Yenta: ISA IRQ mask 0x0ed8, PCI irq 17
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17]
MMIO=[d0208000-d02087ff]  Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[463f02005c594058]
eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
disabled
ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt for device 0000:00:14.6 disabled
ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5
agpgart: Detected Ati IGP9100/M chipset
agpgart: AGP aperture is 32M @ 0xd2000000
USB Universal Host Controller Interface driver v2.3
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.3 (7168 buckets, 57344 max) - 236 bytes per
conntrack
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
NFSD: starting 90-second grace period
nfsd: last server has exited
nfsd: unexporting all filesystems
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
NFSD: starting 90-second grace period

Hope this helps.

David


On Sun, 2005-10-30 at 10:33 -0500, Mark Hahn wrote:
> > The problem I reported on the linux-kernel list and later here.  See
> 
> you mentioned posting the full dmesg(s).  in particular,
> are there differences in /proc/interrupts in working and 
> non-working kernels?  lspci -v might also be interesting.
> 
> > laptop has a P4 Hyperthreaded chip (someone mentioned that there was an
> > ACPI problem related to hyperthreading).
> 
> conceivable, but HT is hardly a new phenomenon.
> 
> 


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-10-30 16:31 ` David Ronis
@ 2005-10-30 18:57   ` Stefan
  2005-10-30 23:02   ` Stefan
  1 sibling, 0 replies; 13+ messages in thread
From: Stefan @ 2005-10-30 18:57 UTC (permalink / raw)
  To: David.Ronis; +Cc: Mark Hahn, linux-ide


Cool, I was about to ask you for that info, from a first look at your
files it looks like you found a bug.
I guess someone has to check for any changes in the atiixp driver since
2.6.12 and if there were no changes,
find out what new feature broke the drivers logic.



David Ronis wrote:

>Hi Mark,
>
>I've copied the information you wanted below.
>
>First in 2.6.12.6:
>
>cat /proc/interrupts
>           CPU0       CPU1       
>  0:      53375          1    IO-APIC-edge  timer
>  1:         47          2    IO-APIC-edge  i8042
>  5:          1          0   IO-APIC-level  ATI IXP
>  8:          1          0    IO-APIC-edge  rtc
> 12:        127          0    IO-APIC-edge  i8042
> 14:       4970          0    IO-APIC-edge  ide0
> 15:          0          0    IO-APIC-edge  ide1
> 16:         28          0   IO-APIC-level  ohci_hcd:usb4, yenta,
>ohci1394
> 17:          1          0   IO-APIC-level  yenta
> 18:          0          0   IO-APIC-level  ohci_hcd:usb5
> 19:          2          0   IO-APIC-level  eth0, ehci_hcd:usb1,
>ohci_hcd:usb2, ohci_hcd:usb3
> 21:         43          0   IO-APIC-level  acpi
>NMI:          0          0 
>LOC:      53271      53277 
>ERR:          0
>MIS:          0
>
>lspci -v
>00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge
>(rev 02)
>	Subsystem: ATI Technologies Inc: Unknown device 1234
>	Flags: bus master, 66Mhz, medium devsel, latency 64
>	Memory at d2000000 (32-bit, prefetchable) [size=32M]
>	Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [a0] AGP version 3.0
>
>00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
>(prog-if 00 [Normal decode])
>	Flags: bus master, 66Mhz, medium devsel, latency 99
>	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
>	I/O behind bridge: 00009000-00009fff
>	Memory behind bridge: d0100000-d01fffff
>	Prefetchable memory behind bridge: e0000000-efffffff
>
>00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev
>01) (prog-if 10 [OHCI])
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 19
>	Memory at d0001000 (32-bit, non-prefetchable) [size=4K]
>
>00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev
>01) (prog-if 10 [OHCI])
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 19
>	Memory at d0002000 (32-bit, non-prefetchable) [size=4K]
>
>00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: 66Mhz, medium devsel
>	I/O ports at 8040 [size=16]
>	Memory at 58000000 (32-bit, non-prefetchable) [size=1K]
>
>00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master
>PCI IDE Controller (prog-if 8a [Master SecP PriP])
>	Subsystem: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE
>Controller
>	Flags: bus master, medium devsel, latency 64, IRQ 16
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at 8060 [size=16]
>
>00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 0
>
>00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if
>01 [Subtractive decode])
>	Flags: bus master, 66Mhz, medium devsel, latency 64
>	Bus: primary=00, secondary=02, subordinate=04, sec-latency=69
>	I/O behind bridge: 0000a000-0000afff
>	Memory behind bridge: d0200000-d02fffff
>
>00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97
>Audio Controller
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, 66Mhz, slow devsel, latency 64, IRQ 5
>	Memory at d0003000 (32-bit, non-prefetchable) [size=256]
>
>00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00
>[Generic])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: 66Mhz, slow devsel, IRQ 5
>	Memory at d0003400 (32-bit, non-prefetchable) [size=256]
>
>01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP
>[Radeon Mobility 9100IGP] (prog-if 00 [VGA])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 66,
>IRQ 10
>	Memory at e0000000 (32-bit, prefetchable) [size=256M]
>	I/O ports at 9000 [size=256]
>	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
>	Expansion ROM at <unassigned> [disabled] [size=128K]
>	Capabilities: [58] AGP version 3.0
>	Capabilities: [50] Power Management version 2
>
>02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
>IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 64, IRQ 16
>	Memory at d0208000 (32-bit, non-prefetchable) [size=2K]
>	Memory at d0200000 (32-bit, non-prefetchable) [size=16K]
>	Capabilities: [44] Power Management version 2
>
>02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g
>Wireless LAN Controller (rev 03)
>	Subsystem: Hewlett-Packard Company: Unknown device 12f4
>	Flags: bus master, fast devsel, latency 64, IRQ 5
>	Memory at d0204000 (32-bit, non-prefetchable) [size=8K]
>
>02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
>RTL-8139/8139C/8139C+ (rev 10)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 128, IRQ 19
>	I/O ports at a000 [size=256]
>	Memory at d0208800 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [50] Power Management version 2
>
>02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
>(rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 168, IRQ 17
>	Memory at 58001000 (32-bit, non-prefetchable) [size=4K]
>	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
>	Memory window 0: 58400000-587ff000 (prefetchable)
>	Memory window 1: 58800000-58bff000
>	I/O window 0: 00004000-000040ff
>	I/O window 1: 00004400-000044ff
>	16-bit legacy interface ports at 0001
>
>02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
>(rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 168, IRQ 16
>	Memory at 58002000 (32-bit, non-prefetchable) [size=4K]
>	Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
>	Memory window 0: 58c00000-58fff000 (prefetchable)
>	Memory window 1: 59000000-593ff000
>	I/O window 0: 00004800-000048ff
>	I/O window 1: 00004c00-00004cff
>	16-bit legacy interface ports at 0001
>
>02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading
>Function (rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 64
>	I/O ports at a400 [size=64]
>	Capabilities: [44] Power Management version 2
>
>02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
>	Subsystem: NEC Corporation USB
>	Flags: bus master, medium devsel, latency 64, IRQ 16
>	Memory at d0206000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [40] Power Management version 2
>
>02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
>	Subsystem: NEC Corporation USB
>	Flags: bus master, medium devsel, latency 64, IRQ 18
>	Memory at d0207000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [40] Power Management version 2
>
>02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20
>[EHCI])
>	Subsystem: NEC Corporation USB 2.0
>	Flags: bus master, medium devsel, latency 64, IRQ 19
>	Memory at d0208c00 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [40] Power Management version 2
>
>
>dmesg
>Linux version 2.6.12.6 (root@montroll.lan) (gcc version 3.4.4) #4 SMP
>Tue Aug 30 20:38:22 EDT 2005
>BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
> BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000047f70000 (usable)
> BIOS-e820: 0000000047f70000 - 0000000047f7d000 (ACPI data)
> BIOS-e820: 0000000047f7d000 - 0000000047f80000 (ACPI NVS)
> BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved)
> BIOS-e820: 0000000057f80000 - 0000000058000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
>Warning only 896MB will be used.
>Use a HIGHMEM enabled kernel.
>896MB LOWMEM available.
>found SMP MP-table at 000f6570
>On node 0 totalpages: 229376
>  DMA zone: 4096 pages, LIFO batch:1
>  Normal zone: 225280 pages, LIFO batch:31
>  HighMem zone: 0 pages, LIFO batch:1
>DMI present.
>ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6600
>ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @
>0x47f791c8
>ACPI: FADT (v001 HP     Chinook  0x06040000 ATI  0x000f4240) @
>0x47f7ceed
>ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @
>0x47f7cf61
>ACPI: SSDT (v001 PTLTD  ACPIHT   0x06040000  LTP 0x00000001) @
>0x47f7cfc9
>ACPI: DSDT (v001     HP    SB200 0x06040000 INTL 0x20030509) @
>0x00000000
>ACPI: PM-Timer IO Port: 0x8008
>ACPI: Local APIC address 0xfee00000
>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>Processor #0 15:2 APIC version 20
>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
>Processor #1 15:2 APIC version 20
>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
>IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
>ACPI: IRQ0 used by override.
>ACPI: IRQ2 used by override.
>Enabling APIC mode:  Flat.  Using 1 I/O APICs
>Using ACPI (MADT) for SMP configuration information
>Allocating PCI resources starting at 58000000 (gap: 58000000:a6c00000)
>Built 1 zonelists
>Kernel command line: BOOT_IMAGE=2.6.12.6 ro root=302
>mapped APIC to ffffd000 (fee00000)
>mapped IOAPIC to ffffc000 (fec00000)
>Initializing CPU#0
>PID hash table entries: 4096 (order: 12, 65536 bytes)
>Detected 3000.728 MHz processor.
>Using pmtmr for high-res timesource
>Console: colour VGA+ 80x25
>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
>Memory: 906084k/917504k available (1695k kernel code, 10908k reserved,
>737k data, 192k init, 0k highmem)
>Checking if this processor honours the WP bit even in supervisor mode...
>Ok.
>Calibrating delay loop... 5963.77 BogoMIPS (lpj=2981888)
>Mount-cache hash table entries: 512
>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: Trace cache: 12K uops, L1 D cache: 8K
>CPU: L2 cache: 512K
>CPU: Physical Processor ID: 0
>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
>00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#0.
>CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
>CPU0: Thermal monitoring enabled
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Checking 'hlt' instruction... OK.
>CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
>Booting processor 1/1 eip 3000
>Initializing CPU#1
>Calibrating delay loop... 5996.54 BogoMIPS (lpj=2998272)
>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: Trace cache: 12K uops, L1 D cache: 8K
>CPU: L2 cache: 512K
>CPU: Physical Processor ID: 0
>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
>00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#1.
>CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
>CPU1: Thermal monitoring enabled
>CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
>Total of 2 processors activated (11960.32 BogoMIPS).
>ENABLING IO-APIC IRQs
>..TIMER: vector=0x31 pin1=2 pin2=-1
>checking TSC synchronization across 2 CPUs: passed.
>Brought up 2 CPUs
>CPU0 attaching sched-domain:
> domain 0: span 3
>  groups: 1 2
>  domain 1: span 3
>   groups: 3
>CPU1 attaching sched-domain:
> domain 0: span 3
>  groups: 2 1
>  domain 1: span 3
>   groups: 3
>NET: Registered protocol family 16
>PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
>PCI: Using configuration type 1
>mtrr: v2.0 (20020519)
>ACPI: Subsystem revision 20050309
>ACPI: Interpreter enabled
>ACPI: Using IOAPIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>PCI: Probing PCI hardware (bus 00)
>PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
>Boot video device is 0000:01:05.0
>PCI: Transparent bridge - 0000:00:14.4
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
>ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled.
>ACPI: Embedded Controller [EC0] (gpe 6)
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
>report
>Machine check exception polling timer started.
>Initializing Cryptographic API
>ACPI: AC Adapter [ACAD] (on-line)
>ACPI: Battery Slot [BAT1] (battery present)
>ACPI: Power Button (FF) [PWRF]
>ACPI: Lid Switch [LID]
>ACPI: Thermal Zone [THRM] (52 C)
>Real Time Clock Driver v1.12
>i8042.c: Detected active multiplexing controller, rev 1.1.
>serio: i8042 AUX0 port at 0x60,0x64 irq 12
>serio: i8042 AUX1 port at 0x60,0x64 irq 12
>serio: i8042 AUX2 port at 0x60,0x64 irq 12
>serio: i8042 AUX3 port at 0x60,0x64 irq 12
>serio: i8042 KBD port at 0x60,0x64 irq 1
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered
>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>ide: Assuming 33MHz system bus speed for PIO modes; override with
>idebus=xx
>ATIIXP: IDE controller at PCI slot 0000:00:14.1
>ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
>ATIIXP: chipset revision 0
>ATIIXP: not 100% native mode: will probe irqs later
>    ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
>    ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
>Probing IDE interface ide0...
>hda: ST9100823A, ATA DISK drive
>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>Probing IDE interface ide1...
>hdc: SD-R2512, ATAPI CD/DVD-ROM drive
>ide1 at 0x170-0x177,0x376 on irq 15
>Probing IDE interface ide2...
>Probing IDE interface ide3...
>Probing IDE interface ide4...
>Probing IDE interface ide5...
>hda: max request size: 128KiB
>hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63,
>UDMA(100)
>hda: cache flushes supported
> hda: hda1 hda2
>mice: PS/2 mouse device common for all mice
>input: PC Speaker
>NET: Registered protocol family 2
>IP: routing cache hash table of 4096 buckets, 64Kbytes
>TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
>TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
>TCP: Hash tables configured (established 131072 bind 65536)
>NET: Registered protocol family 1
>NET: Registered protocol family 15
>ACPI wakeup devices: 
>ELAN USB0 USB1 USB2 KBC0 MSE0 
>ACPI: (supports S0 S3 S4 S5)
>kjournald starting.  Commit interval 5 seconds
>EXT3-fs: mounted filesystem with ordered data mode.
>VFS: Mounted root (ext3 filesystem) readonly.
>Freeing unused kernel memory: 192k freed
>input: AT Translated Set 2 keyboard on isa0060/serio0
>alps.c: Enabling hardware tapping
>input: PS/2 Mouse on isa0060/serio4
>input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
>Adding 977216k swap on /dev/hda1.  Priority:-1 extents:1
>EXT3 FS on hda2, internal journal
>Linux agpgart interface v0.101 (c) Dave Jones
>8139too Fast Ethernet driver 0.9.27
>ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
>eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:01:82:2d, IRQ 19
>eth0:  Identified 8139 chip type 'RTL-8101'
>eth0: link up, 10Mbps, half-duplex, lpa 0x0000
>usbcore: registered new driver usbfs
>usbcore: registered new driver hub
>ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 19
>ehci_hcd 0000:02:07.2: NEC Corporation USB 2.0
>ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1
>ehci_hcd 0000:02:07.2: irq 19, io mem 0xd0208c00
>ehci_hcd 0000:02:07.2: park 0
>ehci_hcd 0000:02:07.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
>2004
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 5 ports detected
>ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
>ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
>ohci_hcd 0000:00:13.0: ATI Technologies Inc OHCI USB Controller #1
>ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
>ohci_hcd 0000:00:13.0: irq 19, io mem 0xd0001000
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
>ohci_hcd 0000:00:13.1: ATI Technologies Inc OHCI USB Controller #2
>ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
>ohci_hcd 0000:00:13.1: irq 19, io mem 0xd0002000
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 16
>ohci_hcd 0000:02:07.0: NEC Corporation USB
>ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4
>ohci_hcd 0000:02:07.0: irq 16, io mem 0xd0206000
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:02:07.1[B] -> GSI 18 (level, low) -> IRQ 18
>ohci_hcd 0000:02:07.1: NEC Corporation USB (#2)
>ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5
>ohci_hcd 0000:02:07.1: irq 18, io mem 0xd0207000
>hub 5-0:1.0: USB hub found
>hub 5-0:1.0: 2 ports detected
>usb 4-1: new low speed USB device using ohci_hcd and address 2
>Linux Kernel Card Services
>  options:  [pci] [cardbus] [pm]
>ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 17
>Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
>Yenta: Enabling burst memory read transactions
>Yenta: Using CSCINT to route CSC interrupts to PCI
>Yenta: Routing CardBus interrupts to PCI
>Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
>Yenta: ISA IRQ mask 0x0ed8, PCI irq 17
>Socket status: 30000006
>ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 16
>Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
>Yenta: Using CSCINT to route CSC interrupts to PCI
>Yenta: Routing CardBus interrupts to PCI
>Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
>input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-1
>usbcore: registered new driver usbhid
>drivers/usb/input/hid-core.c: v2.01:USB HID core driver
>Yenta: ISA IRQ mask 0x0ed8, PCI irq 16
>Socket status: 30000006
>ieee1394: Initialized config rom entry `ip1394'
>ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
>ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
>ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]
>MMIO=[d0208000-d02087ff]  Max Packet=[2048]
>Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing
>disabled
>ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5
>ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5
>agpgart: Detected Ati IGP9100/M chipset
>agpgart: AGP aperture is 32M @ 0xd2000000
>ieee1394: Host added: ID:BUS[0-00:1023]  GUID[463f02005c594058]
>eth1394: $Rev: 1247 $ Ben Collins <bcollins@debian.org>
>eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
>USB Universal Host Controller Interface driver v2.2
>ip_tables: (C) 2000-2002 Netfilter core team
>ip_conntrack version 2.1 (7168 buckets, 57344 max) - 256 bytes per
>conntrack
>Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
>
>Now in 2.6.14:
>
>cat /proc/interrupts
>           CPU0       CPU1       
>  0:     345156          3    IO-APIC-edge  timer
>  1:         51          2    IO-APIC-edge  i8042
>  5:          1          0   IO-APIC-level  ATI IXP
>  8:          1          0    IO-APIC-edge  rtc
> 12:        121          0    IO-APIC-edge  i8042
> 14:       5474          0    IO-APIC-edge  ide0
> 15:          0          0    IO-APIC-edge  ide1
> 16:          1          0   IO-APIC-level  yenta
> 17:         29          0   IO-APIC-level  ohci_hcd:usb4, yenta,
>ohci1394
> 18:          2          0   IO-APIC-level  eth0, ehci_hcd:usb1,
>ohci_hcd:usb2, ohci_hcd:usb3
> 19:          0          0   IO-APIC-level  ohci_hcd:usb5
> 21:         40          0   IO-APIC-level  acpi
>NMI:          0          0 
>LOC:     345004     345037 
>ERR:          0
>MIS:          0
>
>lspci -v
>00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge
>(rev 02)
>	Subsystem: ATI Technologies Inc: Unknown device 1234
>	Flags: bus master, 66Mhz, medium devsel, latency 64
>	Memory at d2000000 (32-bit, prefetchable) [size=32M]
>	Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [a0] AGP version 3.0
>
>00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
>(prog-if 00 [Normal decode])
>	Flags: bus master, 66Mhz, medium devsel, latency 99
>	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
>	I/O behind bridge: 00009000-00009fff
>	Memory behind bridge: d0100000-d01fffff
>	Prefetchable memory behind bridge: e0000000-efffffff
>
>00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev
>01) (prog-if 10 [OHCI])
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18
>	Memory at d0001000 (32-bit, non-prefetchable) [size=4K]
>
>00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev
>01) (prog-if 10 [OHCI])
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18
>	Memory at d0002000 (32-bit, non-prefetchable) [size=4K]
>
>00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: 66Mhz, medium devsel
>	I/O ports at 8040 [size=16]
>	Memory at 64000000 (32-bit, non-prefetchable) [size=1K]
>
>00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master
>PCI IDE Controller (prog-if 8a [Master SecP PriP])
>	Subsystem: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE
>Controller
>	Flags: bus master, medium devsel, latency 64, IRQ 17
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at 8060 [size=16]
>
>00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 0
>
>00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if
>01 [Subtractive decode])
>	Flags: bus master, 66Mhz, medium devsel, latency 64
>	Bus: primary=00, secondary=02, subordinate=04, sec-latency=69
>	I/O behind bridge: 0000a000-0000afff
>	Memory behind bridge: d0200000-d02fffff
>	Prefetchable memory behind bridge: 60000000-63ffffff
>
>00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97
>Audio Controller
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, 66Mhz, slow devsel, latency 64, IRQ 5
>	Memory at d0003000 (32-bit, non-prefetchable) [size=256]
>
>00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00
>[Generic])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: 66Mhz, slow devsel, IRQ 5
>	Memory at d0003400 (32-bit, non-prefetchable) [size=256]
>
>01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP
>[Radeon Mobility 9100IGP] (prog-if 00 [VGA])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 66,
>IRQ 10
>	Memory at e0000000 (32-bit, prefetchable) [size=256M]
>	I/O ports at 9000 [size=256]
>	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
>	Expansion ROM at d0120000 [disabled] [size=128K]
>	Capabilities: [58] AGP version 3.0
>	Capabilities: [50] Power Management version 2
>
>02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
>IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 64, IRQ 17
>	Memory at d0208000 (32-bit, non-prefetchable) [size=2K]
>	Memory at d0200000 (32-bit, non-prefetchable) [size=16K]
>	Capabilities: [44] Power Management version 2
>
>02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g
>Wireless LAN Controller (rev 03)
>	Subsystem: Hewlett-Packard Company: Unknown device 12f4
>	Flags: bus master, fast devsel, latency 64, IRQ 5
>	Memory at d0204000 (32-bit, non-prefetchable) [size=8K]
>
>02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
>RTL-8139/8139C/8139C+ (rev 10)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 128, IRQ 18
>	I/O ports at a000 [size=256]
>	Memory at d0208800 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [50] Power Management version 2
>
>02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
>(rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 168, IRQ 16
>	Memory at d0209000 (32-bit, non-prefetchable) [size=4K]
>	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
>	Memory window 0: 60000000-61fff000 (prefetchable)
>	Memory window 1: 66000000-67fff000
>	I/O window 0: 0000a800-0000a8ff
>	I/O window 1: 0000ac00-0000acff
>	16-bit legacy interface ports at 0001
>
>02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
>(rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 168, IRQ 17
>	Memory at d020a000 (32-bit, non-prefetchable) [size=4K]
>	Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
>	Memory window 0: 62000000-63fff000 (prefetchable)
>	Memory window 1: 68000000-69fff000
>	I/O window 0: 00001400-000014ff
>	I/O window 1: 00001800-000018ff
>	16-bit legacy interface ports at 0001
>
>02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading
>Function (rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 64
>	I/O ports at a400 [size=64]
>	Capabilities: [44] Power Management version 2
>
>02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
>	Subsystem: NEC Corporation USB
>	Flags: bus master, medium devsel, latency 64, IRQ 17
>	Memory at d0206000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [40] Power Management version 2
>
>02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
>	Subsystem: NEC Corporation USB
>	Flags: bus master, medium devsel, latency 64, IRQ 19
>	Memory at d0207000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [40] Power Management version 2
>
>02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20
>[EHCI])
>	Subsystem: NEC Corporation USB 2.0
>	Flags: bus master, medium devsel, latency 64, IRQ 18
>	Memory at d0208c00 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [40] Power Management version 2
>
>
>dmesg
>Linux version 2.6.14 (root@montroll) (gcc version 4.0.2) #10 SMP Fri Oct
>28 15:56:01 EDT 2005
>BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
> BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000047f70000 (usable)
> BIOS-e820: 0000000047f70000 - 0000000047f7d000 (ACPI data)
> BIOS-e820: 0000000047f7d000 - 0000000047f80000 (ACPI NVS)
> BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved)
> BIOS-e820: 0000000057f80000 - 0000000058000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
>Warning only 896MB will be used.
>Use a HIGHMEM enabled kernel.
>896MB LOWMEM available.
>found SMP MP-table at 000f6570
>On node 0 totalpages: 229376
>  DMA zone: 4096 pages, LIFO batch:1
>  Normal zone: 225280 pages, LIFO batch:31
>  HighMem zone: 0 pages, LIFO batch:1
>DMI present.
>ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6600
>ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @
>0x47f791c8
>ACPI: FADT (v001 HP     Chinook  0x06040000 ATI  0x000f4240) @
>0x47f7ceed
>ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @
>0x47f7cf61
>ACPI: SSDT (v001 PTLTD  ACPIHT   0x06040000  LTP 0x00000001) @
>0x47f7cfc9
>ACPI: DSDT (v001     HP    SB200 0x06040000 INTL 0x20030509) @
>0x00000000
>ACPI: PM-Timer IO Port: 0x8008
>ACPI: Local APIC address 0xfee00000
>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>Processor #0 15:2 APIC version 20
>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
>Processor #1 15:2 APIC version 20
>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
>IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
>ACPI: IRQ0 used by override.
>ACPI: IRQ2 used by override.
>Enabling APIC mode:  Flat.  Using 1 I/O APICs
>Using ACPI (MADT) for SMP configuration information
>Allocating PCI resources starting at 60000000 (gap: 58000000:a6c00000)
>Built 1 zonelists
>Kernel command line: BOOT_IMAGE=2.6.14 ro root=302
>mapped APIC to ffffd000 (fee00000)
>mapped IOAPIC to ffffc000 (fec00000)
>Initializing CPU#0
>PID hash table entries: 4096 (order: 12, 65536 bytes)
>Detected 3000.911 MHz processor.
>Using pmtmr for high-res timesource
>Console: colour VGA+ 80x25
>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
>Memory: 906284k/917504k available (1696k kernel code, 10708k reserved,
>531k data, 188k init, 0k highmem)
>Checking if this processor honours the WP bit even in supervisor mode...
>Ok.
>Calibrating delay using timer specific routine.. 6002.40 BogoMIPS
>(lpj=3001201)
>Mount-cache hash table entries: 512
>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: Trace cache: 12K uops, L1 D cache: 8K
>CPU: L2 cache: 512K
>CPU: Physical Processor ID: 0
>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
>00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#0.
>CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
>CPU0: Thermal monitoring enabled
>mtrr: v2.0 (20020519)
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Checking 'hlt' instruction... OK.
>CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
>Booting processor 1/1 eip 2000
>Initializing CPU#1
>Calibrating delay using timer specific routine.. 5999.46 BogoMIPS
>(lpj=2999730)
>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: Trace cache: 12K uops, L1 D cache: 8K
>CPU: L2 cache: 512K
>CPU: Physical Processor ID: 0
>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
>00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#1.
>CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
>CPU1: Thermal monitoring enabled
>CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
>Total of 2 processors activated (12001.86 BogoMIPS).
>ENABLING IO-APIC IRQs
>..TIMER: vector=0x31 pin1=2 pin2=-1
>checking TSC synchronization across 2 CPUs: passed.
>softlockup thread 0 started up.
>Brought up 2 CPUs
>softlockup thread 1 started up.
>NET: Registered protocol family 16
>ACPI: bus type pci registered
>PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
>PCI: Using configuration type 1
>ACPI: Subsystem revision 20050902
>ACPI: Interpreter enabled
>ACPI: Using IOAPIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>PCI: Probing PCI hardware (bus 00)
>ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
>PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
>Boot video device is 0000:01:05.0
>PCI: Transparent bridge - 0000:00:14.4
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
>ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled.
>ACPI: Embedded Controller [EC0] (gpe 6)
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
>report
>PCI: Bridge: 0000:00:01.0
>  IO window: 9000-9fff
>  MEM window: d0100000-d01fffff
>  PREFETCH window: e0000000-efffffff
>PCI: Bus 3, cardbus bridge: 0000:02:04.0
>  IO window: 0000a800-0000a8ff
>  IO window: 0000ac00-0000acff
>  PREFETCH window: 60000000-61ffffff
>  MEM window: 66000000-67ffffff
>PCI: Bus 7, cardbus bridge: 0000:02:04.1
>  IO window: 00001400-000014ff
>  IO window: 00001800-000018ff
>  PREFETCH window: 62000000-63ffffff
>  MEM window: 68000000-69ffffff
>PCI: Bridge: 0000:00:14.4
>  IO window: a000-afff
>  MEM window: d0200000-d02fffff
>  PREFETCH window: 60000000-63ffffff
>ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16
>ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 17
>Machine check exception polling timer started.
>Initializing Cryptographic API
>ACPI: AC Adapter [ACAD] (on-line)
>ACPI: Battery Slot [BAT1] (battery present)
>ACPI: Power Button (FF) [PWRF]
>ACPI: Lid Switch [LID]
>ACPI: Power Button (CM) [PWRB]
>ACPI: CPU0 (power states: C1[C1] C2[C2])
>ACPI: CPU1 (power states: C1[C1] C2[C2])
>ACPI: Thermal Zone [THRM] (52 C)
>Real Time Clock Driver v1.12
>i8042.c: Detected active multiplexing controller, rev 1.1.
>serio: i8042 AUX0 port at 0x60,0x64 irq 12
>serio: i8042 AUX1 port at 0x60,0x64 irq 12
>serio: i8042 AUX2 port at 0x60,0x64 irq 12
>serio: i8042 AUX3 port at 0x60,0x64 irq 12
>serio: i8042 KBD port at 0x60,0x64 irq 1
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered
>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>ide: Assuming 33MHz system bus speed for PIO modes; override with
>idebus=xx
>ATIIXP: IDE controller at PCI slot 0000:00:14.1
>ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
>ATIIXP: chipset revision 0
>ATIIXP: not 100% native mode: will probe irqs later
>    ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
>    ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
>Probing IDE interface ide0...
>hda: ST9100823A, ATA DISK drive
>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>Probing IDE interface ide1...
>hdc: SD-R2512, ATAPI CD/DVD-ROM drive
>ide1 at 0x170-0x177,0x376 on irq 15
>hda: max request size: 128KiB
>hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63,
>UDMA(100)
>hda: cache flushes supported
> hda: hda1 hda2
>mice: PS/2 mouse device common for all mice
>input: PC Speaker
>NET: Registered protocol family 2
>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
>TCP: Hash tables configured (established 131072 bind 65536)
>TCP reno registered
>TCP bic registered
>NET: Registered protocol family 1
>NET: Registered protocol family 15
>Using IPI Shortcut mode
>kjournald starting.  Commit interval 5 seconds
>input: AT Translated Set 2 keyboard on isa0060/serio0
>EXT3-fs: mounted filesystem with ordered data mode.
>VFS: Mounted root (ext3 filesystem) readonly.
>Freeing unused kernel memory: 188k freed
>input: PS/2 Mouse on isa0060/serio4
>input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
>Adding 977216k swap on /dev/hda1.  Priority:-1 extents:1 across:977216k
>EXT3 FS on hda2, internal journal
>Linux agpgart interface v0.101 (c) Dave Jones
>8139too Fast Ethernet driver 0.9.27
>ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 18
>eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:01:82:2d, IRQ 18
>eth0:  Identified 8139 chip type 'RTL-8101'
>eth0: link up, 10Mbps, half-duplex, lpa 0x0000
>usbcore: registered new driver usbfs
>usbcore: registered new driver hub
>ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 18
>ehci_hcd 0000:02:07.2: EHCI Host Controller
>ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1
>ehci_hcd 0000:02:07.2: irq 18, io mem 0xd0208c00
>ehci_hcd 0000:02:07.2: park 0
>ehci_hcd 0000:02:07.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
>2004
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 5 ports detected
>ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver
>(PCI)
>ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 18
>ohci_hcd 0000:00:13.0: OHCI Host Controller
>ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
>ohci_hcd 0000:00:13.0: irq 18, io mem 0xd0001000
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 18
>ohci_hcd 0000:00:13.1: OHCI Host Controller
>ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
>ohci_hcd 0000:00:13.1: irq 18, io mem 0xd0002000
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 17
>ohci_hcd 0000:02:07.0: OHCI Host Controller
>ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4
>ohci_hcd 0000:02:07.0: irq 17, io mem 0xd0206000
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:02:07.1[B] -> GSI 18 (level, low) -> IRQ 19
>ohci_hcd 0000:02:07.1: OHCI Host Controller
>ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5
>ohci_hcd 0000:02:07.1: irq 19, io mem 0xd0207000
>hub 5-0:1.0: USB hub found
>hub 5-0:1.0: 2 ports detected
>usb 4-1: new low speed USB device using ohci_hcd and address 2
>ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16
>Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
>Yenta: Enabling burst memory read transactions
>Yenta: Using CSCINT to route CSC interrupts to PCI
>Yenta: Routing CardBus interrupts to PCI
>Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
>Yenta: ISA IRQ mask 0x0ed8, PCI irq 16
>Socket status: 30000086
>pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
>pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
>pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff
>ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 17
>Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
>Yenta: Using CSCINT to route CSC interrupts to PCI
>Yenta: Routing CardBus interrupts to PCI
>Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
>input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-1
>usbcore: registered new driver usbhid
>drivers/usb/input/hid-core.c: v2.6:USB HID core driver
>Yenta: ISA IRQ mask 0x0ed8, PCI irq 17
>Socket status: 30000006
>pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
>pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
>pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff
>ieee1394: Initialized config rom entry `ip1394'
>ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
>ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17
>ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17]
>MMIO=[d0208000-d02087ff]  Max Packet=[2048]
>ieee1394: Host added: ID:BUS[0-00:1023]  GUID[463f02005c594058]
>eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
>eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
>disabled
>ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5
>ACPI: PCI interrupt for device 0000:00:14.6 disabled
>ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5
>agpgart: Detected Ati IGP9100/M chipset
>agpgart: AGP aperture is 32M @ 0xd2000000
>USB Universal Host Controller Interface driver v2.3
>ip_tables: (C) 2000-2002 Netfilter core team
>ip_conntrack version 2.3 (7168 buckets, 57344 max) - 236 bytes per
>conntrack
>Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
>NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
>directory
>NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
>NFSD: starting 90-second grace period
>nfsd: last server has exited
>nfsd: unexporting all filesystems
>NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
>directory
>NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
>NFSD: starting 90-second grace period
>
>Hope this helps.
>
>David
>
>
>On Sun, 2005-10-30 at 10:33 -0500, Mark Hahn wrote:
>  
>
>>>The problem I reported on the linux-kernel list and later here.  See
>>>      
>>>
>>you mentioned posting the full dmesg(s).  in particular,
>>are there differences in /proc/interrupts in working and 
>>non-working kernels?  lspci -v might also be interesting.
>>
>>    
>>
>>>laptop has a P4 Hyperthreaded chip (someone mentioned that there was an
>>>ACPI problem related to hyperthreading).
>>>      
>>>
>>conceivable, but HT is hardly a new phenomenon.
>>
>>
>>    
>>
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-ide" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>
>  
>


	

	
		
___________________________________________________________ 
Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-10-30 16:31 ` David Ronis
  2005-10-30 18:57   ` Stefan
@ 2005-10-30 23:02   ` Stefan
  2005-10-30 23:08     ` David Ronis
  1 sibling, 1 reply; 13+ messages in thread
From: Stefan @ 2005-10-30 23:02 UTC (permalink / raw)
  To: David.Ronis; +Cc: Mark Hahn, linux-ide

David Ronis wrote:


Hi David, I just checked the diffs of ide and atiixp from 2.6.12.6 to
2.6.14, I don't think those changes caused the problem.

Can you provide some more info?

I would like to see if there are differences in lspci -v output of your
old and your new kernel.
Also could you check if it makes any difference if you switch down to
udma4 udma2 and then test speeds?

>Hi Mark,
>
>I've copied the information you wanted below.
>
>First in 2.6.12.6:
>
>cat /proc/interrupts
>           CPU0       CPU1       
>  0:      53375          1    IO-APIC-edge  timer
>  1:         47          2    IO-APIC-edge  i8042
>  5:          1          0   IO-APIC-level  ATI IXP
>  8:          1          0    IO-APIC-edge  rtc
> 12:        127          0    IO-APIC-edge  i8042
> 14:       4970          0    IO-APIC-edge  ide0
> 15:          0          0    IO-APIC-edge  ide1
> 16:         28          0   IO-APIC-level  ohci_hcd:usb4, yenta,
>ohci1394
> 17:          1          0   IO-APIC-level  yenta
> 18:          0          0   IO-APIC-level  ohci_hcd:usb5
> 19:          2          0   IO-APIC-level  eth0, ehci_hcd:usb1,
>ohci_hcd:usb2, ohci_hcd:usb3
> 21:         43          0   IO-APIC-level  acpi
>NMI:          0          0 
>LOC:      53271      53277 
>ERR:          0
>MIS:          0
>
>lspci -v
>00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge
>(rev 02)
>	Subsystem: ATI Technologies Inc: Unknown device 1234
>	Flags: bus master, 66Mhz, medium devsel, latency 64
>	Memory at d2000000 (32-bit, prefetchable) [size=32M]
>	Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [a0] AGP version 3.0
>
>00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
>(prog-if 00 [Normal decode])
>	Flags: bus master, 66Mhz, medium devsel, latency 99
>	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
>	I/O behind bridge: 00009000-00009fff
>	Memory behind bridge: d0100000-d01fffff
>	Prefetchable memory behind bridge: e0000000-efffffff
>
>00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev
>01) (prog-if 10 [OHCI])
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 19
>	Memory at d0001000 (32-bit, non-prefetchable) [size=4K]
>
>00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev
>01) (prog-if 10 [OHCI])
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 19
>	Memory at d0002000 (32-bit, non-prefetchable) [size=4K]
>
>00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: 66Mhz, medium devsel
>	I/O ports at 8040 [size=16]
>	Memory at 58000000 (32-bit, non-prefetchable) [size=1K]
>
>00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master
>PCI IDE Controller (prog-if 8a [Master SecP PriP])
>	Subsystem: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE
>Controller
>	Flags: bus master, medium devsel, latency 64, IRQ 16
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at 8060 [size=16]
>
>00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 0
>
>00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if
>01 [Subtractive decode])
>	Flags: bus master, 66Mhz, medium devsel, latency 64
>	Bus: primary=00, secondary=02, subordinate=04, sec-latency=69
>	I/O behind bridge: 0000a000-0000afff
>	Memory behind bridge: d0200000-d02fffff
>
>00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97
>Audio Controller
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, 66Mhz, slow devsel, latency 64, IRQ 5
>	Memory at d0003000 (32-bit, non-prefetchable) [size=256]
>
>00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00
>[Generic])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: 66Mhz, slow devsel, IRQ 5
>	Memory at d0003400 (32-bit, non-prefetchable) [size=256]
>
>01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP
>[Radeon Mobility 9100IGP] (prog-if 00 [VGA])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 66,
>IRQ 10
>	Memory at e0000000 (32-bit, prefetchable) [size=256M]
>	I/O ports at 9000 [size=256]
>	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
>	Expansion ROM at <unassigned> [disabled] [size=128K]
>	Capabilities: [58] AGP version 3.0
>	Capabilities: [50] Power Management version 2
>
>02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
>IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 64, IRQ 16
>	Memory at d0208000 (32-bit, non-prefetchable) [size=2K]
>	Memory at d0200000 (32-bit, non-prefetchable) [size=16K]
>	Capabilities: [44] Power Management version 2
>
>02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g
>Wireless LAN Controller (rev 03)
>	Subsystem: Hewlett-Packard Company: Unknown device 12f4
>	Flags: bus master, fast devsel, latency 64, IRQ 5
>	Memory at d0204000 (32-bit, non-prefetchable) [size=8K]
>
>02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
>RTL-8139/8139C/8139C+ (rev 10)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 128, IRQ 19
>	I/O ports at a000 [size=256]
>	Memory at d0208800 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [50] Power Management version 2
>
>02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
>(rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 168, IRQ 17
>	Memory at 58001000 (32-bit, non-prefetchable) [size=4K]
>	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
>	Memory window 0: 58400000-587ff000 (prefetchable)
>	Memory window 1: 58800000-58bff000
>	I/O window 0: 00004000-000040ff
>	I/O window 1: 00004400-000044ff
>	16-bit legacy interface ports at 0001
>
>02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
>(rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 168, IRQ 16
>	Memory at 58002000 (32-bit, non-prefetchable) [size=4K]
>	Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
>	Memory window 0: 58c00000-58fff000 (prefetchable)
>	Memory window 1: 59000000-593ff000
>	I/O window 0: 00004800-000048ff
>	I/O window 1: 00004c00-00004cff
>	16-bit legacy interface ports at 0001
>
>02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading
>Function (rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 64
>	I/O ports at a400 [size=64]
>	Capabilities: [44] Power Management version 2
>
>02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
>	Subsystem: NEC Corporation USB
>	Flags: bus master, medium devsel, latency 64, IRQ 16
>	Memory at d0206000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [40] Power Management version 2
>
>02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
>	Subsystem: NEC Corporation USB
>	Flags: bus master, medium devsel, latency 64, IRQ 18
>	Memory at d0207000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [40] Power Management version 2
>
>02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20
>[EHCI])
>	Subsystem: NEC Corporation USB 2.0
>	Flags: bus master, medium devsel, latency 64, IRQ 19
>	Memory at d0208c00 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [40] Power Management version 2
>
>
>dmesg
>Linux version 2.6.12.6 (root@montroll.lan) (gcc version 3.4.4) #4 SMP
>Tue Aug 30 20:38:22 EDT 2005
>BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
> BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000047f70000 (usable)
> BIOS-e820: 0000000047f70000 - 0000000047f7d000 (ACPI data)
> BIOS-e820: 0000000047f7d000 - 0000000047f80000 (ACPI NVS)
> BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved)
> BIOS-e820: 0000000057f80000 - 0000000058000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
>Warning only 896MB will be used.
>Use a HIGHMEM enabled kernel.
>896MB LOWMEM available.
>found SMP MP-table at 000f6570
>On node 0 totalpages: 229376
>  DMA zone: 4096 pages, LIFO batch:1
>  Normal zone: 225280 pages, LIFO batch:31
>  HighMem zone: 0 pages, LIFO batch:1
>DMI present.
>ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6600
>ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @
>0x47f791c8
>ACPI: FADT (v001 HP     Chinook  0x06040000 ATI  0x000f4240) @
>0x47f7ceed
>ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @
>0x47f7cf61
>ACPI: SSDT (v001 PTLTD  ACPIHT   0x06040000  LTP 0x00000001) @
>0x47f7cfc9
>ACPI: DSDT (v001     HP    SB200 0x06040000 INTL 0x20030509) @
>0x00000000
>ACPI: PM-Timer IO Port: 0x8008
>ACPI: Local APIC address 0xfee00000
>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>Processor #0 15:2 APIC version 20
>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
>Processor #1 15:2 APIC version 20
>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
>IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
>ACPI: IRQ0 used by override.
>ACPI: IRQ2 used by override.
>Enabling APIC mode:  Flat.  Using 1 I/O APICs
>Using ACPI (MADT) for SMP configuration information
>Allocating PCI resources starting at 58000000 (gap: 58000000:a6c00000)
>Built 1 zonelists
>Kernel command line: BOOT_IMAGE=2.6.12.6 ro root=302
>mapped APIC to ffffd000 (fee00000)
>mapped IOAPIC to ffffc000 (fec00000)
>Initializing CPU#0
>PID hash table entries: 4096 (order: 12, 65536 bytes)
>Detected 3000.728 MHz processor.
>Using pmtmr for high-res timesource
>Console: colour VGA+ 80x25
>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
>Memory: 906084k/917504k available (1695k kernel code, 10908k reserved,
>737k data, 192k init, 0k highmem)
>Checking if this processor honours the WP bit even in supervisor mode...
>Ok.
>Calibrating delay loop... 5963.77 BogoMIPS (lpj=2981888)
>Mount-cache hash table entries: 512
>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: Trace cache: 12K uops, L1 D cache: 8K
>CPU: L2 cache: 512K
>CPU: Physical Processor ID: 0
>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
>00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#0.
>CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
>CPU0: Thermal monitoring enabled
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Checking 'hlt' instruction... OK.
>CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
>Booting processor 1/1 eip 3000
>Initializing CPU#1
>Calibrating delay loop... 5996.54 BogoMIPS (lpj=2998272)
>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: Trace cache: 12K uops, L1 D cache: 8K
>CPU: L2 cache: 512K
>CPU: Physical Processor ID: 0
>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
>00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#1.
>CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
>CPU1: Thermal monitoring enabled
>CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
>Total of 2 processors activated (11960.32 BogoMIPS).
>ENABLING IO-APIC IRQs
>..TIMER: vector=0x31 pin1=2 pin2=-1
>checking TSC synchronization across 2 CPUs: passed.
>Brought up 2 CPUs
>CPU0 attaching sched-domain:
> domain 0: span 3
>  groups: 1 2
>  domain 1: span 3
>   groups: 3
>CPU1 attaching sched-domain:
> domain 0: span 3
>  groups: 2 1
>  domain 1: span 3
>   groups: 3
>NET: Registered protocol family 16
>PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
>PCI: Using configuration type 1
>mtrr: v2.0 (20020519)
>ACPI: Subsystem revision 20050309
>ACPI: Interpreter enabled
>ACPI: Using IOAPIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>PCI: Probing PCI hardware (bus 00)
>PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
>Boot video device is 0000:01:05.0
>PCI: Transparent bridge - 0000:00:14.4
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
>ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled.
>ACPI: Embedded Controller [EC0] (gpe 6)
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
>report
>Machine check exception polling timer started.
>Initializing Cryptographic API
>ACPI: AC Adapter [ACAD] (on-line)
>ACPI: Battery Slot [BAT1] (battery present)
>ACPI: Power Button (FF) [PWRF]
>ACPI: Lid Switch [LID]
>ACPI: Thermal Zone [THRM] (52 C)
>Real Time Clock Driver v1.12
>i8042.c: Detected active multiplexing controller, rev 1.1.
>serio: i8042 AUX0 port at 0x60,0x64 irq 12
>serio: i8042 AUX1 port at 0x60,0x64 irq 12
>serio: i8042 AUX2 port at 0x60,0x64 irq 12
>serio: i8042 AUX3 port at 0x60,0x64 irq 12
>serio: i8042 KBD port at 0x60,0x64 irq 1
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered
>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>ide: Assuming 33MHz system bus speed for PIO modes; override with
>idebus=xx
>ATIIXP: IDE controller at PCI slot 0000:00:14.1
>ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
>ATIIXP: chipset revision 0
>ATIIXP: not 100% native mode: will probe irqs later
>    ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
>    ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
>Probing IDE interface ide0...
>hda: ST9100823A, ATA DISK drive
>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>Probing IDE interface ide1...
>hdc: SD-R2512, ATAPI CD/DVD-ROM drive
>ide1 at 0x170-0x177,0x376 on irq 15
>Probing IDE interface ide2...
>Probing IDE interface ide3...
>Probing IDE interface ide4...
>Probing IDE interface ide5...
>hda: max request size: 128KiB
>hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63,
>UDMA(100)
>hda: cache flushes supported
> hda: hda1 hda2
>mice: PS/2 mouse device common for all mice
>input: PC Speaker
>NET: Registered protocol family 2
>IP: routing cache hash table of 4096 buckets, 64Kbytes
>TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
>TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
>TCP: Hash tables configured (established 131072 bind 65536)
>NET: Registered protocol family 1
>NET: Registered protocol family 15
>ACPI wakeup devices: 
>ELAN USB0 USB1 USB2 KBC0 MSE0 
>ACPI: (supports S0 S3 S4 S5)
>kjournald starting.  Commit interval 5 seconds
>EXT3-fs: mounted filesystem with ordered data mode.
>VFS: Mounted root (ext3 filesystem) readonly.
>Freeing unused kernel memory: 192k freed
>input: AT Translated Set 2 keyboard on isa0060/serio0
>alps.c: Enabling hardware tapping
>input: PS/2 Mouse on isa0060/serio4
>input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
>Adding 977216k swap on /dev/hda1.  Priority:-1 extents:1
>EXT3 FS on hda2, internal journal
>Linux agpgart interface v0.101 (c) Dave Jones
>8139too Fast Ethernet driver 0.9.27
>ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
>eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:01:82:2d, IRQ 19
>eth0:  Identified 8139 chip type 'RTL-8101'
>eth0: link up, 10Mbps, half-duplex, lpa 0x0000
>usbcore: registered new driver usbfs
>usbcore: registered new driver hub
>ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 19
>ehci_hcd 0000:02:07.2: NEC Corporation USB 2.0
>ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1
>ehci_hcd 0000:02:07.2: irq 19, io mem 0xd0208c00
>ehci_hcd 0000:02:07.2: park 0
>ehci_hcd 0000:02:07.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
>2004
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 5 ports detected
>ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
>ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
>ohci_hcd 0000:00:13.0: ATI Technologies Inc OHCI USB Controller #1
>ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
>ohci_hcd 0000:00:13.0: irq 19, io mem 0xd0001000
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
>ohci_hcd 0000:00:13.1: ATI Technologies Inc OHCI USB Controller #2
>ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
>ohci_hcd 0000:00:13.1: irq 19, io mem 0xd0002000
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 16
>ohci_hcd 0000:02:07.0: NEC Corporation USB
>ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4
>ohci_hcd 0000:02:07.0: irq 16, io mem 0xd0206000
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:02:07.1[B] -> GSI 18 (level, low) -> IRQ 18
>ohci_hcd 0000:02:07.1: NEC Corporation USB (#2)
>ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5
>ohci_hcd 0000:02:07.1: irq 18, io mem 0xd0207000
>hub 5-0:1.0: USB hub found
>hub 5-0:1.0: 2 ports detected
>usb 4-1: new low speed USB device using ohci_hcd and address 2
>Linux Kernel Card Services
>  options:  [pci] [cardbus] [pm]
>ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 17
>Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
>Yenta: Enabling burst memory read transactions
>Yenta: Using CSCINT to route CSC interrupts to PCI
>Yenta: Routing CardBus interrupts to PCI
>Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
>Yenta: ISA IRQ mask 0x0ed8, PCI irq 17
>Socket status: 30000006
>ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 16
>Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
>Yenta: Using CSCINT to route CSC interrupts to PCI
>Yenta: Routing CardBus interrupts to PCI
>Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
>input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-1
>usbcore: registered new driver usbhid
>drivers/usb/input/hid-core.c: v2.01:USB HID core driver
>Yenta: ISA IRQ mask 0x0ed8, PCI irq 16
>Socket status: 30000006
>ieee1394: Initialized config rom entry `ip1394'
>ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
>ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
>ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]
>MMIO=[d0208000-d02087ff]  Max Packet=[2048]
>Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing
>disabled
>ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5
>ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5
>agpgart: Detected Ati IGP9100/M chipset
>agpgart: AGP aperture is 32M @ 0xd2000000
>ieee1394: Host added: ID:BUS[0-00:1023]  GUID[463f02005c594058]
>eth1394: $Rev: 1247 $ Ben Collins <bcollins@debian.org>
>eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
>USB Universal Host Controller Interface driver v2.2
>ip_tables: (C) 2000-2002 Netfilter core team
>ip_conntrack version 2.1 (7168 buckets, 57344 max) - 256 bytes per
>conntrack
>Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
>
>Now in 2.6.14:
>
>cat /proc/interrupts
>           CPU0       CPU1       
>  0:     345156          3    IO-APIC-edge  timer
>  1:         51          2    IO-APIC-edge  i8042
>  5:          1          0   IO-APIC-level  ATI IXP
>  8:          1          0    IO-APIC-edge  rtc
> 12:        121          0    IO-APIC-edge  i8042
> 14:       5474          0    IO-APIC-edge  ide0
> 15:          0          0    IO-APIC-edge  ide1
> 16:          1          0   IO-APIC-level  yenta
> 17:         29          0   IO-APIC-level  ohci_hcd:usb4, yenta,
>ohci1394
> 18:          2          0   IO-APIC-level  eth0, ehci_hcd:usb1,
>ohci_hcd:usb2, ohci_hcd:usb3
> 19:          0          0   IO-APIC-level  ohci_hcd:usb5
> 21:         40          0   IO-APIC-level  acpi
>NMI:          0          0 
>LOC:     345004     345037 
>ERR:          0
>MIS:          0
>
>lspci -v
>00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge
>(rev 02)
>	Subsystem: ATI Technologies Inc: Unknown device 1234
>	Flags: bus master, 66Mhz, medium devsel, latency 64
>	Memory at d2000000 (32-bit, prefetchable) [size=32M]
>	Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [a0] AGP version 3.0
>
>00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
>(prog-if 00 [Normal decode])
>	Flags: bus master, 66Mhz, medium devsel, latency 99
>	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
>	I/O behind bridge: 00009000-00009fff
>	Memory behind bridge: d0100000-d01fffff
>	Prefetchable memory behind bridge: e0000000-efffffff
>
>00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev
>01) (prog-if 10 [OHCI])
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18
>	Memory at d0001000 (32-bit, non-prefetchable) [size=4K]
>
>00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev
>01) (prog-if 10 [OHCI])
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18
>	Memory at d0002000 (32-bit, non-prefetchable) [size=4K]
>
>00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: 66Mhz, medium devsel
>	I/O ports at 8040 [size=16]
>	Memory at 64000000 (32-bit, non-prefetchable) [size=1K]
>
>00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master
>PCI IDE Controller (prog-if 8a [Master SecP PriP])
>	Subsystem: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE
>Controller
>	Flags: bus master, medium devsel, latency 64, IRQ 17
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at <ignored>
>	I/O ports at 8060 [size=16]
>
>00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c
>	Subsystem: ATI Technologies Inc: Unknown device 434c
>	Flags: bus master, 66Mhz, medium devsel, latency 0
>
>00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if
>01 [Subtractive decode])
>	Flags: bus master, 66Mhz, medium devsel, latency 64
>	Bus: primary=00, secondary=02, subordinate=04, sec-latency=69
>	I/O behind bridge: 0000a000-0000afff
>	Memory behind bridge: d0200000-d02fffff
>	Prefetchable memory behind bridge: 60000000-63ffffff
>
>00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97
>Audio Controller
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, 66Mhz, slow devsel, latency 64, IRQ 5
>	Memory at d0003000 (32-bit, non-prefetchable) [size=256]
>
>00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00
>[Generic])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: 66Mhz, slow devsel, IRQ 5
>	Memory at d0003400 (32-bit, non-prefetchable) [size=256]
>
>01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP
>[Radeon Mobility 9100IGP] (prog-if 00 [VGA])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 66,
>IRQ 10
>	Memory at e0000000 (32-bit, prefetchable) [size=256M]
>	I/O ports at 9000 [size=256]
>	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
>	Expansion ROM at d0120000 [disabled] [size=128K]
>	Capabilities: [58] AGP version 3.0
>	Capabilities: [50] Power Management version 2
>
>02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
>IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 64, IRQ 17
>	Memory at d0208000 (32-bit, non-prefetchable) [size=2K]
>	Memory at d0200000 (32-bit, non-prefetchable) [size=16K]
>	Capabilities: [44] Power Management version 2
>
>02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g
>Wireless LAN Controller (rev 03)
>	Subsystem: Hewlett-Packard Company: Unknown device 12f4
>	Flags: bus master, fast devsel, latency 64, IRQ 5
>	Memory at d0204000 (32-bit, non-prefetchable) [size=8K]
>
>02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
>RTL-8139/8139C/8139C+ (rev 10)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 128, IRQ 18
>	I/O ports at a000 [size=256]
>	Memory at d0208800 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [50] Power Management version 2
>
>02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
>(rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 168, IRQ 16
>	Memory at d0209000 (32-bit, non-prefetchable) [size=4K]
>	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
>	Memory window 0: 60000000-61fff000 (prefetchable)
>	Memory window 1: 66000000-67fff000
>	I/O window 0: 0000a800-0000a8ff
>	I/O window 1: 0000ac00-0000acff
>	16-bit legacy interface ports at 0001
>
>02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
>(rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 168, IRQ 17
>	Memory at d020a000 (32-bit, non-prefetchable) [size=4K]
>	Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
>	Memory window 0: 62000000-63fff000 (prefetchable)
>	Memory window 1: 68000000-69fff000
>	I/O window 0: 00001400-000014ff
>	I/O window 1: 00001800-000018ff
>	16-bit legacy interface ports at 0001
>
>02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading
>Function (rev 01)
>	Subsystem: Hewlett-Packard Company: Unknown device 006b
>	Flags: bus master, medium devsel, latency 64
>	I/O ports at a400 [size=64]
>	Capabilities: [44] Power Management version 2
>
>02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
>	Subsystem: NEC Corporation USB
>	Flags: bus master, medium devsel, latency 64, IRQ 17
>	Memory at d0206000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [40] Power Management version 2
>
>02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
>	Subsystem: NEC Corporation USB
>	Flags: bus master, medium devsel, latency 64, IRQ 19
>	Memory at d0207000 (32-bit, non-prefetchable) [size=4K]
>	Capabilities: [40] Power Management version 2
>
>02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20
>[EHCI])
>	Subsystem: NEC Corporation USB 2.0
>	Flags: bus master, medium devsel, latency 64, IRQ 18
>	Memory at d0208c00 (32-bit, non-prefetchable) [size=256]
>	Capabilities: [40] Power Management version 2
>
>
>dmesg
>Linux version 2.6.14 (root@montroll) (gcc version 4.0.2) #10 SMP Fri Oct
>28 15:56:01 EDT 2005
>BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
> BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000047f70000 (usable)
> BIOS-e820: 0000000047f70000 - 0000000047f7d000 (ACPI data)
> BIOS-e820: 0000000047f7d000 - 0000000047f80000 (ACPI NVS)
> BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved)
> BIOS-e820: 0000000057f80000 - 0000000058000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
>Warning only 896MB will be used.
>Use a HIGHMEM enabled kernel.
>896MB LOWMEM available.
>found SMP MP-table at 000f6570
>On node 0 totalpages: 229376
>  DMA zone: 4096 pages, LIFO batch:1
>  Normal zone: 225280 pages, LIFO batch:31
>  HighMem zone: 0 pages, LIFO batch:1
>DMI present.
>ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6600
>ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @
>0x47f791c8
>ACPI: FADT (v001 HP     Chinook  0x06040000 ATI  0x000f4240) @
>0x47f7ceed
>ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @
>0x47f7cf61
>ACPI: SSDT (v001 PTLTD  ACPIHT   0x06040000  LTP 0x00000001) @
>0x47f7cfc9
>ACPI: DSDT (v001     HP    SB200 0x06040000 INTL 0x20030509) @
>0x00000000
>ACPI: PM-Timer IO Port: 0x8008
>ACPI: Local APIC address 0xfee00000
>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>Processor #0 15:2 APIC version 20
>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
>Processor #1 15:2 APIC version 20
>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
>IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
>ACPI: IRQ0 used by override.
>ACPI: IRQ2 used by override.
>Enabling APIC mode:  Flat.  Using 1 I/O APICs
>Using ACPI (MADT) for SMP configuration information
>Allocating PCI resources starting at 60000000 (gap: 58000000:a6c00000)
>Built 1 zonelists
>Kernel command line: BOOT_IMAGE=2.6.14 ro root=302
>mapped APIC to ffffd000 (fee00000)
>mapped IOAPIC to ffffc000 (fec00000)
>Initializing CPU#0
>PID hash table entries: 4096 (order: 12, 65536 bytes)
>Detected 3000.911 MHz processor.
>Using pmtmr for high-res timesource
>Console: colour VGA+ 80x25
>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
>Memory: 906284k/917504k available (1696k kernel code, 10708k reserved,
>531k data, 188k init, 0k highmem)
>Checking if this processor honours the WP bit even in supervisor mode...
>Ok.
>Calibrating delay using timer specific routine.. 6002.40 BogoMIPS
>(lpj=3001201)
>Mount-cache hash table entries: 512
>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: Trace cache: 12K uops, L1 D cache: 8K
>CPU: L2 cache: 512K
>CPU: Physical Processor ID: 0
>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
>00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#0.
>CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
>CPU0: Thermal monitoring enabled
>mtrr: v2.0 (20020519)
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Checking 'hlt' instruction... OK.
>CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
>Booting processor 1/1 eip 2000
>Initializing CPU#1
>Calibrating delay using timer specific routine.. 5999.46 BogoMIPS
>(lpj=2999730)
>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
>00004400 00000000 00000000
>CPU: Trace cache: 12K uops, L1 D cache: 8K
>CPU: L2 cache: 512K
>CPU: Physical Processor ID: 0
>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
>00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#1.
>CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
>CPU1: Thermal monitoring enabled
>CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
>Total of 2 processors activated (12001.86 BogoMIPS).
>ENABLING IO-APIC IRQs
>..TIMER: vector=0x31 pin1=2 pin2=-1
>checking TSC synchronization across 2 CPUs: passed.
>softlockup thread 0 started up.
>Brought up 2 CPUs
>softlockup thread 1 started up.
>NET: Registered protocol family 16
>ACPI: bus type pci registered
>PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
>PCI: Using configuration type 1
>ACPI: Subsystem revision 20050902
>ACPI: Interpreter enabled
>ACPI: Using IOAPIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>PCI: Probing PCI hardware (bus 00)
>ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
>PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
>Boot video device is 0000:01:05.0
>PCI: Transparent bridge - 0000:00:14.4
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
>ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled.
>ACPI: Embedded Controller [EC0] (gpe 6)
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
>report
>PCI: Bridge: 0000:00:01.0
>  IO window: 9000-9fff
>  MEM window: d0100000-d01fffff
>  PREFETCH window: e0000000-efffffff
>PCI: Bus 3, cardbus bridge: 0000:02:04.0
>  IO window: 0000a800-0000a8ff
>  IO window: 0000ac00-0000acff
>  PREFETCH window: 60000000-61ffffff
>  MEM window: 66000000-67ffffff
>PCI: Bus 7, cardbus bridge: 0000:02:04.1
>  IO window: 00001400-000014ff
>  IO window: 00001800-000018ff
>  PREFETCH window: 62000000-63ffffff
>  MEM window: 68000000-69ffffff
>PCI: Bridge: 0000:00:14.4
>  IO window: a000-afff
>  MEM window: d0200000-d02fffff
>  PREFETCH window: 60000000-63ffffff
>ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16
>ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 17
>Machine check exception polling timer started.
>Initializing Cryptographic API
>ACPI: AC Adapter [ACAD] (on-line)
>ACPI: Battery Slot [BAT1] (battery present)
>ACPI: Power Button (FF) [PWRF]
>ACPI: Lid Switch [LID]
>ACPI: Power Button (CM) [PWRB]
>ACPI: CPU0 (power states: C1[C1] C2[C2])
>ACPI: CPU1 (power states: C1[C1] C2[C2])
>ACPI: Thermal Zone [THRM] (52 C)
>Real Time Clock Driver v1.12
>i8042.c: Detected active multiplexing controller, rev 1.1.
>serio: i8042 AUX0 port at 0x60,0x64 irq 12
>serio: i8042 AUX1 port at 0x60,0x64 irq 12
>serio: i8042 AUX2 port at 0x60,0x64 irq 12
>serio: i8042 AUX3 port at 0x60,0x64 irq 12
>serio: i8042 KBD port at 0x60,0x64 irq 1
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered
>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>ide: Assuming 33MHz system bus speed for PIO modes; override with
>idebus=xx
>ATIIXP: IDE controller at PCI slot 0000:00:14.1
>ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
>ATIIXP: chipset revision 0
>ATIIXP: not 100% native mode: will probe irqs later
>    ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
>    ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
>Probing IDE interface ide0...
>hda: ST9100823A, ATA DISK drive
>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>Probing IDE interface ide1...
>hdc: SD-R2512, ATAPI CD/DVD-ROM drive
>ide1 at 0x170-0x177,0x376 on irq 15
>hda: max request size: 128KiB
>hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63,
>UDMA(100)
>hda: cache flushes supported
> hda: hda1 hda2
>mice: PS/2 mouse device common for all mice
>input: PC Speaker
>NET: Registered protocol family 2
>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
>TCP: Hash tables configured (established 131072 bind 65536)
>TCP reno registered
>TCP bic registered
>NET: Registered protocol family 1
>NET: Registered protocol family 15
>Using IPI Shortcut mode
>kjournald starting.  Commit interval 5 seconds
>input: AT Translated Set 2 keyboard on isa0060/serio0
>EXT3-fs: mounted filesystem with ordered data mode.
>VFS: Mounted root (ext3 filesystem) readonly.
>Freeing unused kernel memory: 188k freed
>input: PS/2 Mouse on isa0060/serio4
>input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
>Adding 977216k swap on /dev/hda1.  Priority:-1 extents:1 across:977216k
>EXT3 FS on hda2, internal journal
>Linux agpgart interface v0.101 (c) Dave Jones
>8139too Fast Ethernet driver 0.9.27
>ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 18
>eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:01:82:2d, IRQ 18
>eth0:  Identified 8139 chip type 'RTL-8101'
>eth0: link up, 10Mbps, half-duplex, lpa 0x0000
>usbcore: registered new driver usbfs
>usbcore: registered new driver hub
>ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 18
>ehci_hcd 0000:02:07.2: EHCI Host Controller
>ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1
>ehci_hcd 0000:02:07.2: irq 18, io mem 0xd0208c00
>ehci_hcd 0000:02:07.2: park 0
>ehci_hcd 0000:02:07.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
>2004
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 5 ports detected
>ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver
>(PCI)
>ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 18
>ohci_hcd 0000:00:13.0: OHCI Host Controller
>ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
>ohci_hcd 0000:00:13.0: irq 18, io mem 0xd0001000
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 18
>ohci_hcd 0000:00:13.1: OHCI Host Controller
>ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
>ohci_hcd 0000:00:13.1: irq 18, io mem 0xd0002000
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 17
>ohci_hcd 0000:02:07.0: OHCI Host Controller
>ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4
>ohci_hcd 0000:02:07.0: irq 17, io mem 0xd0206000
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 3 ports detected
>ACPI: PCI Interrupt 0000:02:07.1[B] -> GSI 18 (level, low) -> IRQ 19
>ohci_hcd 0000:02:07.1: OHCI Host Controller
>ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5
>ohci_hcd 0000:02:07.1: irq 19, io mem 0xd0207000
>hub 5-0:1.0: USB hub found
>hub 5-0:1.0: 2 ports detected
>usb 4-1: new low speed USB device using ohci_hcd and address 2
>ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16
>Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
>Yenta: Enabling burst memory read transactions
>Yenta: Using CSCINT to route CSC interrupts to PCI
>Yenta: Routing CardBus interrupts to PCI
>Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
>Yenta: ISA IRQ mask 0x0ed8, PCI irq 16
>Socket status: 30000086
>pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
>pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
>pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff
>ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 17
>Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
>Yenta: Using CSCINT to route CSC interrupts to PCI
>Yenta: Routing CardBus interrupts to PCI
>Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
>input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-1
>usbcore: registered new driver usbhid
>drivers/usb/input/hid-core.c: v2.6:USB HID core driver
>Yenta: ISA IRQ mask 0x0ed8, PCI irq 17
>Socket status: 30000006
>pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
>pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
>pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff
>ieee1394: Initialized config rom entry `ip1394'
>ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
>ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17
>ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17]
>MMIO=[d0208000-d02087ff]  Max Packet=[2048]
>ieee1394: Host added: ID:BUS[0-00:1023]  GUID[463f02005c594058]
>eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
>eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
>disabled
>ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5
>ACPI: PCI interrupt for device 0000:00:14.6 disabled
>ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5
>agpgart: Detected Ati IGP9100/M chipset
>agpgart: AGP aperture is 32M @ 0xd2000000
>USB Universal Host Controller Interface driver v2.3
>ip_tables: (C) 2000-2002 Netfilter core team
>ip_conntrack version 2.3 (7168 buckets, 57344 max) - 236 bytes per
>conntrack
>Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
>NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
>directory
>NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
>NFSD: starting 90-second grace period
>nfsd: last server has exited
>nfsd: unexporting all filesystems
>NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
>directory
>NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
>NFSD: starting 90-second grace period
>
>Hope this helps.
>
>David
>
>
>On Sun, 2005-10-30 at 10:33 -0500, Mark Hahn wrote:
>  
>
>>>The problem I reported on the linux-kernel list and later here.  See
>>>      
>>>
>>you mentioned posting the full dmesg(s).  in particular,
>>are there differences in /proc/interrupts in working and 
>>non-working kernels?  lspci -v might also be interesting.
>>
>>    
>>
>>>laptop has a P4 Hyperthreaded chip (someone mentioned that there was an
>>>ACPI problem related to hyperthreading).
>>>      
>>>
>>conceivable, but HT is hardly a new phenomenon.
>>
>>
>>    
>>
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-ide" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>
>  
>


	

	
		
___________________________________________________________ 
Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-10-30 23:02   ` Stefan
@ 2005-10-30 23:08     ` David Ronis
  2005-10-30 23:38       ` Stefan
  0 siblings, 1 reply; 13+ messages in thread
From: David Ronis @ 2005-10-30 23:08 UTC (permalink / raw)
  To: Stefan; +Cc: David.Ronis, Mark Hahn, linux-ide

Hi Stefan,

The lspci -v output is in the email I sent to Mark (and cc'd the list).
I diff'ed the output, and there are lots of differences; most seem
trivial (addresses & IRQ's).   As to switching to the lower modes I'll
try (maybe later tonight).

Thanks for your help.

David

On Mon, 2005-10-31 at 00:02 +0100, Stefan wrote:
> David Ronis wrote:
> 
> 
> Hi David, I just checked the diffs of ide and atiixp from 2.6.12.6 to
> 2.6.14, I don't think those changes caused the problem.
> 
> Can you provide some more info?
> 
> I would like to see if there are differences in lspci -v output of your
> old and your new kernel.
> Also could you check if it makes any difference if you switch down to
> udma4 udma2 and then test speeds?
> 
> >Hi Mark,
> >
> >I've copied the information you wanted below.
> >
> >First in 2.6.12.6:
> >
> >cat /proc/interrupts
> >           CPU0       CPU1       
> >  0:      53375          1    IO-APIC-edge  timer
> >  1:         47          2    IO-APIC-edge  i8042
> >  5:          1          0   IO-APIC-level  ATI IXP
> >  8:          1          0    IO-APIC-edge  rtc
> > 12:        127          0    IO-APIC-edge  i8042
> > 14:       4970          0    IO-APIC-edge  ide0
> > 15:          0          0    IO-APIC-edge  ide1
> > 16:         28          0   IO-APIC-level  ohci_hcd:usb4, yenta,
> >ohci1394
> > 17:          1          0   IO-APIC-level  yenta
> > 18:          0          0   IO-APIC-level  ohci_hcd:usb5
> > 19:          2          0   IO-APIC-level  eth0, ehci_hcd:usb1,
> >ohci_hcd:usb2, ohci_hcd:usb3
> > 21:         43          0   IO-APIC-level  acpi
> >NMI:          0          0 
> >LOC:      53271      53277 
> >ERR:          0
> >MIS:          0
> >
> >lspci -v
> >00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge
> >(rev 02)
> >	Subsystem: ATI Technologies Inc: Unknown device 1234
> >	Flags: bus master, 66Mhz, medium devsel, latency 64
> >	Memory at d2000000 (32-bit, prefetchable) [size=32M]
> >	Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
> >	Capabilities: [a0] AGP version 3.0
> >
> >00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
> >(prog-if 00 [Normal decode])
> >	Flags: bus master, 66Mhz, medium devsel, latency 99
> >	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
> >	I/O behind bridge: 00009000-00009fff
> >	Memory behind bridge: d0100000-d01fffff
> >	Prefetchable memory behind bridge: e0000000-efffffff
> >
> >00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev
> >01) (prog-if 10 [OHCI])
> >	Subsystem: ATI Technologies Inc: Unknown device 434c
> >	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 19
> >	Memory at d0001000 (32-bit, non-prefetchable) [size=4K]
> >
> >00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev
> >01) (prog-if 10 [OHCI])
> >	Subsystem: ATI Technologies Inc: Unknown device 434c
> >	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 19
> >	Memory at d0002000 (32-bit, non-prefetchable) [size=4K]
> >
> >00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16)
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: 66Mhz, medium devsel
> >	I/O ports at 8040 [size=16]
> >	Memory at 58000000 (32-bit, non-prefetchable) [size=1K]
> >
> >00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master
> >PCI IDE Controller (prog-if 8a [Master SecP PriP])
> >	Subsystem: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE
> >Controller
> >	Flags: bus master, medium devsel, latency 64, IRQ 16
> >	I/O ports at <ignored>
> >	I/O ports at <ignored>
> >	I/O ports at <ignored>
> >	I/O ports at <ignored>
> >	I/O ports at 8060 [size=16]
> >
> >00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c
> >	Subsystem: ATI Technologies Inc: Unknown device 434c
> >	Flags: bus master, 66Mhz, medium devsel, latency 0
> >
> >00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if
> >01 [Subtractive decode])
> >	Flags: bus master, 66Mhz, medium devsel, latency 64
> >	Bus: primary=00, secondary=02, subordinate=04, sec-latency=69
> >	I/O behind bridge: 0000a000-0000afff
> >	Memory behind bridge: d0200000-d02fffff
> >
> >00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97
> >Audio Controller
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, 66Mhz, slow devsel, latency 64, IRQ 5
> >	Memory at d0003000 (32-bit, non-prefetchable) [size=256]
> >
> >00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00
> >[Generic])
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: 66Mhz, slow devsel, IRQ 5
> >	Memory at d0003400 (32-bit, non-prefetchable) [size=256]
> >
> >01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP
> >[Radeon Mobility 9100IGP] (prog-if 00 [VGA])
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 66,
> >IRQ 10
> >	Memory at e0000000 (32-bit, prefetchable) [size=256M]
> >	I/O ports at 9000 [size=256]
> >	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
> >	Expansion ROM at <unassigned> [disabled] [size=128K]
> >	Capabilities: [58] AGP version 3.0
> >	Capabilities: [50] Power Management version 2
> >
> >02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
> >IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, medium devsel, latency 64, IRQ 16
> >	Memory at d0208000 (32-bit, non-prefetchable) [size=2K]
> >	Memory at d0200000 (32-bit, non-prefetchable) [size=16K]
> >	Capabilities: [44] Power Management version 2
> >
> >02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g
> >Wireless LAN Controller (rev 03)
> >	Subsystem: Hewlett-Packard Company: Unknown device 12f4
> >	Flags: bus master, fast devsel, latency 64, IRQ 5
> >	Memory at d0204000 (32-bit, non-prefetchable) [size=8K]
> >
> >02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> >RTL-8139/8139C/8139C+ (rev 10)
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, medium devsel, latency 128, IRQ 19
> >	I/O ports at a000 [size=256]
> >	Memory at d0208800 (32-bit, non-prefetchable) [size=256]
> >	Capabilities: [50] Power Management version 2
> >
> >02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
> >(rev 01)
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, medium devsel, latency 168, IRQ 17
> >	Memory at 58001000 (32-bit, non-prefetchable) [size=4K]
> >	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
> >	Memory window 0: 58400000-587ff000 (prefetchable)
> >	Memory window 1: 58800000-58bff000
> >	I/O window 0: 00004000-000040ff
> >	I/O window 1: 00004400-000044ff
> >	16-bit legacy interface ports at 0001
> >
> >02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
> >(rev 01)
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, medium devsel, latency 168, IRQ 16
> >	Memory at 58002000 (32-bit, non-prefetchable) [size=4K]
> >	Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
> >	Memory window 0: 58c00000-58fff000 (prefetchable)
> >	Memory window 1: 59000000-593ff000
> >	I/O window 0: 00004800-000048ff
> >	I/O window 1: 00004c00-00004cff
> >	16-bit legacy interface ports at 0001
> >
> >02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading
> >Function (rev 01)
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, medium devsel, latency 64
> >	I/O ports at a400 [size=64]
> >	Capabilities: [44] Power Management version 2
> >
> >02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
> >	Subsystem: NEC Corporation USB
> >	Flags: bus master, medium devsel, latency 64, IRQ 16
> >	Memory at d0206000 (32-bit, non-prefetchable) [size=4K]
> >	Capabilities: [40] Power Management version 2
> >
> >02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
> >	Subsystem: NEC Corporation USB
> >	Flags: bus master, medium devsel, latency 64, IRQ 18
> >	Memory at d0207000 (32-bit, non-prefetchable) [size=4K]
> >	Capabilities: [40] Power Management version 2
> >
> >02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20
> >[EHCI])
> >	Subsystem: NEC Corporation USB 2.0
> >	Flags: bus master, medium devsel, latency 64, IRQ 19
> >	Memory at d0208c00 (32-bit, non-prefetchable) [size=256]
> >	Capabilities: [40] Power Management version 2
> >
> >
> >dmesg
> >Linux version 2.6.12.6 (root@montroll.lan) (gcc version 3.4.4) #4 SMP
> >Tue Aug 30 20:38:22 EDT 2005
> >BIOS-provided physical RAM map:
> > BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
> > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
> > BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
> > BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
> > BIOS-e820: 0000000000100000 - 0000000047f70000 (usable)
> > BIOS-e820: 0000000047f70000 - 0000000047f7d000 (ACPI data)
> > BIOS-e820: 0000000047f7d000 - 0000000047f80000 (ACPI NVS)
> > BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved)
> > BIOS-e820: 0000000057f80000 - 0000000058000000 (reserved)
> > BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> > BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
> >Warning only 896MB will be used.
> >Use a HIGHMEM enabled kernel.
> >896MB LOWMEM available.
> >found SMP MP-table at 000f6570
> >On node 0 totalpages: 229376
> >  DMA zone: 4096 pages, LIFO batch:1
> >  Normal zone: 225280 pages, LIFO batch:31
> >  HighMem zone: 0 pages, LIFO batch:1
> >DMI present.
> >ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6600
> >ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @
> >0x47f791c8
> >ACPI: FADT (v001 HP     Chinook  0x06040000 ATI  0x000f4240) @
> >0x47f7ceed
> >ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @
> >0x47f7cf61
> >ACPI: SSDT (v001 PTLTD  ACPIHT   0x06040000  LTP 0x00000001) @
> >0x47f7cfc9
> >ACPI: DSDT (v001     HP    SB200 0x06040000 INTL 0x20030509) @
> >0x00000000
> >ACPI: PM-Timer IO Port: 0x8008
> >ACPI: Local APIC address 0xfee00000
> >ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
> >Processor #0 15:2 APIC version 20
> >ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
> >Processor #1 15:2 APIC version 20
> >ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
> >ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
> >ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> >IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
> >ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
> >ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
> >ACPI: IRQ0 used by override.
> >ACPI: IRQ2 used by override.
> >Enabling APIC mode:  Flat.  Using 1 I/O APICs
> >Using ACPI (MADT) for SMP configuration information
> >Allocating PCI resources starting at 58000000 (gap: 58000000:a6c00000)
> >Built 1 zonelists
> >Kernel command line: BOOT_IMAGE=2.6.12.6 ro root=302
> >mapped APIC to ffffd000 (fee00000)
> >mapped IOAPIC to ffffc000 (fec00000)
> >Initializing CPU#0
> >PID hash table entries: 4096 (order: 12, 65536 bytes)
> >Detected 3000.728 MHz processor.
> >Using pmtmr for high-res timesource
> >Console: colour VGA+ 80x25
> >Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> >Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> >Memory: 906084k/917504k available (1695k kernel code, 10908k reserved,
> >737k data, 192k init, 0k highmem)
> >Checking if this processor honours the WP bit even in supervisor mode...
> >Ok.
> >Calibrating delay loop... 5963.77 BogoMIPS (lpj=2981888)
> >Mount-cache hash table entries: 512
> >CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
> >00004400 00000000 00000000
> >CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
> >00004400 00000000 00000000
> >CPU: Trace cache: 12K uops, L1 D cache: 8K
> >CPU: L2 cache: 512K
> >CPU: Physical Processor ID: 0
> >CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
> >00000000 00000000
> >Intel machine check architecture supported.
> >Intel machine check reporting enabled on CPU#0.
> >CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
> >CPU0: Thermal monitoring enabled
> >Enabling fast FPU save and restore... done.
> >Enabling unmasked SIMD FPU exception support... done.
> >Checking 'hlt' instruction... OK.
> >CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
> >Booting processor 1/1 eip 3000
> >Initializing CPU#1
> >Calibrating delay loop... 5996.54 BogoMIPS (lpj=2998272)
> >CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
> >00004400 00000000 00000000
> >CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
> >00004400 00000000 00000000
> >CPU: Trace cache: 12K uops, L1 D cache: 8K
> >CPU: L2 cache: 512K
> >CPU: Physical Processor ID: 0
> >CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
> >00000000 00000000
> >Intel machine check architecture supported.
> >Intel machine check reporting enabled on CPU#1.
> >CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
> >CPU1: Thermal monitoring enabled
> >CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
> >Total of 2 processors activated (11960.32 BogoMIPS).
> >ENABLING IO-APIC IRQs
> >..TIMER: vector=0x31 pin1=2 pin2=-1
> >checking TSC synchronization across 2 CPUs: passed.
> >Brought up 2 CPUs
> >CPU0 attaching sched-domain:
> > domain 0: span 3
> >  groups: 1 2
> >  domain 1: span 3
> >   groups: 3
> >CPU1 attaching sched-domain:
> > domain 0: span 3
> >  groups: 2 1
> >  domain 1: span 3
> >   groups: 3
> >NET: Registered protocol family 16
> >PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
> >PCI: Using configuration type 1
> >mtrr: v2.0 (20020519)
> >ACPI: Subsystem revision 20050309
> >ACPI: Interpreter enabled
> >ACPI: Using IOAPIC for interrupt routing
> >ACPI: PCI Root Bridge [PCI0] (0000:00)
> >PCI: Probing PCI hardware (bus 00)
> >PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
> >Boot video device is 0000:01:05.0
> >PCI: Transparent bridge - 0000:00:14.4
> >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
> >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
> >ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled.
> >ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled.
> >ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled.
> >ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled.
> >ACPI: Embedded Controller [EC0] (gpe 6)
> >PCI: Using ACPI for IRQ routing
> >PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
> >report
> >Machine check exception polling timer started.
> >Initializing Cryptographic API
> >ACPI: AC Adapter [ACAD] (on-line)
> >ACPI: Battery Slot [BAT1] (battery present)
> >ACPI: Power Button (FF) [PWRF]
> >ACPI: Lid Switch [LID]
> >ACPI: Thermal Zone [THRM] (52 C)
> >Real Time Clock Driver v1.12
> >i8042.c: Detected active multiplexing controller, rev 1.1.
> >serio: i8042 AUX0 port at 0x60,0x64 irq 12
> >serio: i8042 AUX1 port at 0x60,0x64 irq 12
> >serio: i8042 AUX2 port at 0x60,0x64 irq 12
> >serio: i8042 AUX3 port at 0x60,0x64 irq 12
> >serio: i8042 KBD port at 0x60,0x64 irq 1
> >io scheduler noop registered
> >io scheduler anticipatory registered
> >io scheduler deadline registered
> >io scheduler cfq registered
> >Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> >ide: Assuming 33MHz system bus speed for PIO modes; override with
> >idebus=xx
> >ATIIXP: IDE controller at PCI slot 0000:00:14.1
> >ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
> >ATIIXP: chipset revision 0
> >ATIIXP: not 100% native mode: will probe irqs later
> >    ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
> >    ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
> >Probing IDE interface ide0...
> >hda: ST9100823A, ATA DISK drive
> >ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> >Probing IDE interface ide1...
> >hdc: SD-R2512, ATAPI CD/DVD-ROM drive
> >ide1 at 0x170-0x177,0x376 on irq 15
> >Probing IDE interface ide2...
> >Probing IDE interface ide3...
> >Probing IDE interface ide4...
> >Probing IDE interface ide5...
> >hda: max request size: 128KiB
> >hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63,
> >UDMA(100)
> >hda: cache flushes supported
> > hda: hda1 hda2
> >mice: PS/2 mouse device common for all mice
> >input: PC Speaker
> >NET: Registered protocol family 2
> >IP: routing cache hash table of 4096 buckets, 64Kbytes
> >TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
> >TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
> >TCP: Hash tables configured (established 131072 bind 65536)
> >NET: Registered protocol family 1
> >NET: Registered protocol family 15
> >ACPI wakeup devices: 
> >ELAN USB0 USB1 USB2 KBC0 MSE0 
> >ACPI: (supports S0 S3 S4 S5)
> >kjournald starting.  Commit interval 5 seconds
> >EXT3-fs: mounted filesystem with ordered data mode.
> >VFS: Mounted root (ext3 filesystem) readonly.
> >Freeing unused kernel memory: 192k freed
> >input: AT Translated Set 2 keyboard on isa0060/serio0
> >alps.c: Enabling hardware tapping
> >input: PS/2 Mouse on isa0060/serio4
> >input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
> >Adding 977216k swap on /dev/hda1.  Priority:-1 extents:1
> >EXT3 FS on hda2, internal journal
> >Linux agpgart interface v0.101 (c) Dave Jones
> >8139too Fast Ethernet driver 0.9.27
> >ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
> >eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:01:82:2d, IRQ 19
> >eth0:  Identified 8139 chip type 'RTL-8101'
> >eth0: link up, 10Mbps, half-duplex, lpa 0x0000
> >usbcore: registered new driver usbfs
> >usbcore: registered new driver hub
> >ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 19
> >ehci_hcd 0000:02:07.2: NEC Corporation USB 2.0
> >ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1
> >ehci_hcd 0000:02:07.2: irq 19, io mem 0xd0208c00
> >ehci_hcd 0000:02:07.2: park 0
> >ehci_hcd 0000:02:07.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
> >2004
> >hub 1-0:1.0: USB hub found
> >hub 1-0:1.0: 5 ports detected
> >ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
> >ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
> >ohci_hcd 0000:00:13.0: ATI Technologies Inc OHCI USB Controller #1
> >ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
> >ohci_hcd 0000:00:13.0: irq 19, io mem 0xd0001000
> >hub 2-0:1.0: USB hub found
> >hub 2-0:1.0: 3 ports detected
> >ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
> >ohci_hcd 0000:00:13.1: ATI Technologies Inc OHCI USB Controller #2
> >ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
> >ohci_hcd 0000:00:13.1: irq 19, io mem 0xd0002000
> >hub 3-0:1.0: USB hub found
> >hub 3-0:1.0: 3 ports detected
> >ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 16
> >ohci_hcd 0000:02:07.0: NEC Corporation USB
> >ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4
> >ohci_hcd 0000:02:07.0: irq 16, io mem 0xd0206000
> >hub 4-0:1.0: USB hub found
> >hub 4-0:1.0: 3 ports detected
> >ACPI: PCI Interrupt 0000:02:07.1[B] -> GSI 18 (level, low) -> IRQ 18
> >ohci_hcd 0000:02:07.1: NEC Corporation USB (#2)
> >ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5
> >ohci_hcd 0000:02:07.1: irq 18, io mem 0xd0207000
> >hub 5-0:1.0: USB hub found
> >hub 5-0:1.0: 2 ports detected
> >usb 4-1: new low speed USB device using ohci_hcd and address 2
> >Linux Kernel Card Services
> >  options:  [pci] [cardbus] [pm]
> >ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 17
> >Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
> >Yenta: Enabling burst memory read transactions
> >Yenta: Using CSCINT to route CSC interrupts to PCI
> >Yenta: Routing CardBus interrupts to PCI
> >Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
> >Yenta: ISA IRQ mask 0x0ed8, PCI irq 17
> >Socket status: 30000006
> >ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 16
> >Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
> >Yenta: Using CSCINT to route CSC interrupts to PCI
> >Yenta: Routing CardBus interrupts to PCI
> >Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
> >input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-1
> >usbcore: registered new driver usbhid
> >drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> >Yenta: ISA IRQ mask 0x0ed8, PCI irq 16
> >Socket status: 30000006
> >ieee1394: Initialized config rom entry `ip1394'
> >ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
> >ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
> >ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]
> >MMIO=[d0208000-d02087ff]  Max Packet=[2048]
> >Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing
> >disabled
> >ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5
> >ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5
> >agpgart: Detected Ati IGP9100/M chipset
> >agpgart: AGP aperture is 32M @ 0xd2000000
> >ieee1394: Host added: ID:BUS[0-00:1023]  GUID[463f02005c594058]
> >eth1394: $Rev: 1247 $ Ben Collins <bcollins@debian.org>
> >eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
> >USB Universal Host Controller Interface driver v2.2
> >ip_tables: (C) 2000-2002 Netfilter core team
> >ip_conntrack version 2.1 (7168 buckets, 57344 max) - 256 bytes per
> >conntrack
> >Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> >
> >Now in 2.6.14:
> >
> >cat /proc/interrupts
> >           CPU0       CPU1       
> >  0:     345156          3    IO-APIC-edge  timer
> >  1:         51          2    IO-APIC-edge  i8042
> >  5:          1          0   IO-APIC-level  ATI IXP
> >  8:          1          0    IO-APIC-edge  rtc
> > 12:        121          0    IO-APIC-edge  i8042
> > 14:       5474          0    IO-APIC-edge  ide0
> > 15:          0          0    IO-APIC-edge  ide1
> > 16:          1          0   IO-APIC-level  yenta
> > 17:         29          0   IO-APIC-level  ohci_hcd:usb4, yenta,
> >ohci1394
> > 18:          2          0   IO-APIC-level  eth0, ehci_hcd:usb1,
> >ohci_hcd:usb2, ohci_hcd:usb3
> > 19:          0          0   IO-APIC-level  ohci_hcd:usb5
> > 21:         40          0   IO-APIC-level  acpi
> >NMI:          0          0 
> >LOC:     345004     345037 
> >ERR:          0
> >MIS:          0
> >
> >lspci -v
> >00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge
> >(rev 02)
> >	Subsystem: ATI Technologies Inc: Unknown device 1234
> >	Flags: bus master, 66Mhz, medium devsel, latency 64
> >	Memory at d2000000 (32-bit, prefetchable) [size=32M]
> >	Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
> >	Capabilities: [a0] AGP version 3.0
> >
> >00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
> >(prog-if 00 [Normal decode])
> >	Flags: bus master, 66Mhz, medium devsel, latency 99
> >	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
> >	I/O behind bridge: 00009000-00009fff
> >	Memory behind bridge: d0100000-d01fffff
> >	Prefetchable memory behind bridge: e0000000-efffffff
> >
> >00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev
> >01) (prog-if 10 [OHCI])
> >	Subsystem: ATI Technologies Inc: Unknown device 434c
> >	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18
> >	Memory at d0001000 (32-bit, non-prefetchable) [size=4K]
> >
> >00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev
> >01) (prog-if 10 [OHCI])
> >	Subsystem: ATI Technologies Inc: Unknown device 434c
> >	Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18
> >	Memory at d0002000 (32-bit, non-prefetchable) [size=4K]
> >
> >00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16)
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: 66Mhz, medium devsel
> >	I/O ports at 8040 [size=16]
> >	Memory at 64000000 (32-bit, non-prefetchable) [size=1K]
> >
> >00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master
> >PCI IDE Controller (prog-if 8a [Master SecP PriP])
> >	Subsystem: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE
> >Controller
> >	Flags: bus master, medium devsel, latency 64, IRQ 17
> >	I/O ports at <ignored>
> >	I/O ports at <ignored>
> >	I/O ports at <ignored>
> >	I/O ports at <ignored>
> >	I/O ports at 8060 [size=16]
> >
> >00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c
> >	Subsystem: ATI Technologies Inc: Unknown device 434c
> >	Flags: bus master, 66Mhz, medium devsel, latency 0
> >
> >00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if
> >01 [Subtractive decode])
> >	Flags: bus master, 66Mhz, medium devsel, latency 64
> >	Bus: primary=00, secondary=02, subordinate=04, sec-latency=69
> >	I/O behind bridge: 0000a000-0000afff
> >	Memory behind bridge: d0200000-d02fffff
> >	Prefetchable memory behind bridge: 60000000-63ffffff
> >
> >00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97
> >Audio Controller
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, 66Mhz, slow devsel, latency 64, IRQ 5
> >	Memory at d0003000 (32-bit, non-prefetchable) [size=256]
> >
> >00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00
> >[Generic])
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: 66Mhz, slow devsel, IRQ 5
> >	Memory at d0003400 (32-bit, non-prefetchable) [size=256]
> >
> >01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP
> >[Radeon Mobility 9100IGP] (prog-if 00 [VGA])
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 66,
> >IRQ 10
> >	Memory at e0000000 (32-bit, prefetchable) [size=256M]
> >	I/O ports at 9000 [size=256]
> >	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
> >	Expansion ROM at d0120000 [disabled] [size=128K]
> >	Capabilities: [58] AGP version 3.0
> >	Capabilities: [50] Power Management version 2
> >
> >02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
> >IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, medium devsel, latency 64, IRQ 17
> >	Memory at d0208000 (32-bit, non-prefetchable) [size=2K]
> >	Memory at d0200000 (32-bit, non-prefetchable) [size=16K]
> >	Capabilities: [44] Power Management version 2
> >
> >02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g
> >Wireless LAN Controller (rev 03)
> >	Subsystem: Hewlett-Packard Company: Unknown device 12f4
> >	Flags: bus master, fast devsel, latency 64, IRQ 5
> >	Memory at d0204000 (32-bit, non-prefetchable) [size=8K]
> >
> >02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> >RTL-8139/8139C/8139C+ (rev 10)
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, medium devsel, latency 128, IRQ 18
> >	I/O ports at a000 [size=256]
> >	Memory at d0208800 (32-bit, non-prefetchable) [size=256]
> >	Capabilities: [50] Power Management version 2
> >
> >02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
> >(rev 01)
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, medium devsel, latency 168, IRQ 16
> >	Memory at d0209000 (32-bit, non-prefetchable) [size=4K]
> >	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
> >	Memory window 0: 60000000-61fff000 (prefetchable)
> >	Memory window 1: 66000000-67fff000
> >	I/O window 0: 0000a800-0000a8ff
> >	I/O window 1: 0000ac00-0000acff
> >	16-bit legacy interface ports at 0001
> >
> >02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
> >(rev 01)
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, medium devsel, latency 168, IRQ 17
> >	Memory at d020a000 (32-bit, non-prefetchable) [size=4K]
> >	Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
> >	Memory window 0: 62000000-63fff000 (prefetchable)
> >	Memory window 1: 68000000-69fff000
> >	I/O window 0: 00001400-000014ff
> >	I/O window 1: 00001800-000018ff
> >	16-bit legacy interface ports at 0001
> >
> >02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading
> >Function (rev 01)
> >	Subsystem: Hewlett-Packard Company: Unknown device 006b
> >	Flags: bus master, medium devsel, latency 64
> >	I/O ports at a400 [size=64]
> >	Capabilities: [44] Power Management version 2
> >
> >02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
> >	Subsystem: NEC Corporation USB
> >	Flags: bus master, medium devsel, latency 64, IRQ 17
> >	Memory at d0206000 (32-bit, non-prefetchable) [size=4K]
> >	Capabilities: [40] Power Management version 2
> >
> >02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
> >	Subsystem: NEC Corporation USB
> >	Flags: bus master, medium devsel, latency 64, IRQ 19
> >	Memory at d0207000 (32-bit, non-prefetchable) [size=4K]
> >	Capabilities: [40] Power Management version 2
> >
> >02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20
> >[EHCI])
> >	Subsystem: NEC Corporation USB 2.0
> >	Flags: bus master, medium devsel, latency 64, IRQ 18
> >	Memory at d0208c00 (32-bit, non-prefetchable) [size=256]
> >	Capabilities: [40] Power Management version 2
> >
> >
> >dmesg
> >Linux version 2.6.14 (root@montroll) (gcc version 4.0.2) #10 SMP Fri Oct
> >28 15:56:01 EDT 2005
> >BIOS-provided physical RAM map:
> > BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
> > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
> > BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
> > BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
> > BIOS-e820: 0000000000100000 - 0000000047f70000 (usable)
> > BIOS-e820: 0000000047f70000 - 0000000047f7d000 (ACPI data)
> > BIOS-e820: 0000000047f7d000 - 0000000047f80000 (ACPI NVS)
> > BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved)
> > BIOS-e820: 0000000057f80000 - 0000000058000000 (reserved)
> > BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> > BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
> >Warning only 896MB will be used.
> >Use a HIGHMEM enabled kernel.
> >896MB LOWMEM available.
> >found SMP MP-table at 000f6570
> >On node 0 totalpages: 229376
> >  DMA zone: 4096 pages, LIFO batch:1
> >  Normal zone: 225280 pages, LIFO batch:31
> >  HighMem zone: 0 pages, LIFO batch:1
> >DMI present.
> >ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6600
> >ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @
> >0x47f791c8
> >ACPI: FADT (v001 HP     Chinook  0x06040000 ATI  0x000f4240) @
> >0x47f7ceed
> >ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @
> >0x47f7cf61
> >ACPI: SSDT (v001 PTLTD  ACPIHT   0x06040000  LTP 0x00000001) @
> >0x47f7cfc9
> >ACPI: DSDT (v001     HP    SB200 0x06040000 INTL 0x20030509) @
> >0x00000000
> >ACPI: PM-Timer IO Port: 0x8008
> >ACPI: Local APIC address 0xfee00000
> >ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
> >Processor #0 15:2 APIC version 20
> >ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
> >Processor #1 15:2 APIC version 20
> >ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
> >ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
> >ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> >IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
> >ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
> >ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
> >ACPI: IRQ0 used by override.
> >ACPI: IRQ2 used by override.
> >Enabling APIC mode:  Flat.  Using 1 I/O APICs
> >Using ACPI (MADT) for SMP configuration information
> >Allocating PCI resources starting at 60000000 (gap: 58000000:a6c00000)
> >Built 1 zonelists
> >Kernel command line: BOOT_IMAGE=2.6.14 ro root=302
> >mapped APIC to ffffd000 (fee00000)
> >mapped IOAPIC to ffffc000 (fec00000)
> >Initializing CPU#0
> >PID hash table entries: 4096 (order: 12, 65536 bytes)
> >Detected 3000.911 MHz processor.
> >Using pmtmr for high-res timesource
> >Console: colour VGA+ 80x25
> >Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> >Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> >Memory: 906284k/917504k available (1696k kernel code, 10708k reserved,
> >531k data, 188k init, 0k highmem)
> >Checking if this processor honours the WP bit even in supervisor mode...
> >Ok.
> >Calibrating delay using timer specific routine.. 6002.40 BogoMIPS
> >(lpj=3001201)
> >Mount-cache hash table entries: 512
> >CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
> >00004400 00000000 00000000
> >CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
> >00004400 00000000 00000000
> >CPU: Trace cache: 12K uops, L1 D cache: 8K
> >CPU: L2 cache: 512K
> >CPU: Physical Processor ID: 0
> >CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
> >00000000 00000000
> >Intel machine check architecture supported.
> >Intel machine check reporting enabled on CPU#0.
> >CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
> >CPU0: Thermal monitoring enabled
> >mtrr: v2.0 (20020519)
> >Enabling fast FPU save and restore... done.
> >Enabling unmasked SIMD FPU exception support... done.
> >Checking 'hlt' instruction... OK.
> >CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
> >Booting processor 1/1 eip 2000
> >Initializing CPU#1
> >Calibrating delay using timer specific routine.. 5999.46 BogoMIPS
> >(lpj=2999730)
> >CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
> >00004400 00000000 00000000
> >CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
> >00004400 00000000 00000000
> >CPU: Trace cache: 12K uops, L1 D cache: 8K
> >CPU: L2 cache: 512K
> >CPU: Physical Processor ID: 0
> >CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
> >00000000 00000000
> >Intel machine check architecture supported.
> >Intel machine check reporting enabled on CPU#1.
> >CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
> >CPU1: Thermal monitoring enabled
> >CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
> >Total of 2 processors activated (12001.86 BogoMIPS).
> >ENABLING IO-APIC IRQs
> >..TIMER: vector=0x31 pin1=2 pin2=-1
> >checking TSC synchronization across 2 CPUs: passed.
> >softlockup thread 0 started up.
> >Brought up 2 CPUs
> >softlockup thread 1 started up.
> >NET: Registered protocol family 16
> >ACPI: bus type pci registered
> >PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
> >PCI: Using configuration type 1
> >ACPI: Subsystem revision 20050902
> >ACPI: Interpreter enabled
> >ACPI: Using IOAPIC for interrupt routing
> >ACPI: PCI Root Bridge [PCI0] (0000:00)
> >PCI: Probing PCI hardware (bus 00)
> >ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
> >PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
> >Boot video device is 0000:01:05.0
> >PCI: Transparent bridge - 0000:00:14.4
> >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
> >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
> >ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled.
> >ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled.
> >ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled.
> >ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled.
> >ACPI: Embedded Controller [EC0] (gpe 6)
> >PCI: Using ACPI for IRQ routing
> >PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
> >report
> >PCI: Bridge: 0000:00:01.0
> >  IO window: 9000-9fff
> >  MEM window: d0100000-d01fffff
> >  PREFETCH window: e0000000-efffffff
> >PCI: Bus 3, cardbus bridge: 0000:02:04.0
> >  IO window: 0000a800-0000a8ff
> >  IO window: 0000ac00-0000acff
> >  PREFETCH window: 60000000-61ffffff
> >  MEM window: 66000000-67ffffff
> >PCI: Bus 7, cardbus bridge: 0000:02:04.1
> >  IO window: 00001400-000014ff
> >  IO window: 00001800-000018ff
> >  PREFETCH window: 62000000-63ffffff
> >  MEM window: 68000000-69ffffff
> >PCI: Bridge: 0000:00:14.4
> >  IO window: a000-afff
> >  MEM window: d0200000-d02fffff
> >  PREFETCH window: 60000000-63ffffff
> >ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16
> >ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 17
> >Machine check exception polling timer started.
> >Initializing Cryptographic API
> >ACPI: AC Adapter [ACAD] (on-line)
> >ACPI: Battery Slot [BAT1] (battery present)
> >ACPI: Power Button (FF) [PWRF]
> >ACPI: Lid Switch [LID]
> >ACPI: Power Button (CM) [PWRB]
> >ACPI: CPU0 (power states: C1[C1] C2[C2])
> >ACPI: CPU1 (power states: C1[C1] C2[C2])
> >ACPI: Thermal Zone [THRM] (52 C)
> >Real Time Clock Driver v1.12
> >i8042.c: Detected active multiplexing controller, rev 1.1.
> >serio: i8042 AUX0 port at 0x60,0x64 irq 12
> >serio: i8042 AUX1 port at 0x60,0x64 irq 12
> >serio: i8042 AUX2 port at 0x60,0x64 irq 12
> >serio: i8042 AUX3 port at 0x60,0x64 irq 12
> >serio: i8042 KBD port at 0x60,0x64 irq 1
> >io scheduler noop registered
> >io scheduler anticipatory registered
> >io scheduler deadline registered
> >io scheduler cfq registered
> >Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> >ide: Assuming 33MHz system bus speed for PIO modes; override with
> >idebus=xx
> >ATIIXP: IDE controller at PCI slot 0000:00:14.1
> >ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
> >ATIIXP: chipset revision 0
> >ATIIXP: not 100% native mode: will probe irqs later
> >    ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
> >    ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
> >Probing IDE interface ide0...
> >hda: ST9100823A, ATA DISK drive
> >ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> >Probing IDE interface ide1...
> >hdc: SD-R2512, ATAPI CD/DVD-ROM drive
> >ide1 at 0x170-0x177,0x376 on irq 15
> >hda: max request size: 128KiB
> >hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63,
> >UDMA(100)
> >hda: cache flushes supported
> > hda: hda1 hda2
> >mice: PS/2 mouse device common for all mice
> >input: PC Speaker
> >NET: Registered protocol family 2
> >IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
> >TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
> >TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
> >TCP: Hash tables configured (established 131072 bind 65536)
> >TCP reno registered
> >TCP bic registered
> >NET: Registered protocol family 1
> >NET: Registered protocol family 15
> >Using IPI Shortcut mode
> >kjournald starting.  Commit interval 5 seconds
> >input: AT Translated Set 2 keyboard on isa0060/serio0
> >EXT3-fs: mounted filesystem with ordered data mode.
> >VFS: Mounted root (ext3 filesystem) readonly.
> >Freeing unused kernel memory: 188k freed
> >input: PS/2 Mouse on isa0060/serio4
> >input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
> >Adding 977216k swap on /dev/hda1.  Priority:-1 extents:1 across:977216k
> >EXT3 FS on hda2, internal journal
> >Linux agpgart interface v0.101 (c) Dave Jones
> >8139too Fast Ethernet driver 0.9.27
> >ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 18
> >eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:01:82:2d, IRQ 18
> >eth0:  Identified 8139 chip type 'RTL-8101'
> >eth0: link up, 10Mbps, half-duplex, lpa 0x0000
> >usbcore: registered new driver usbfs
> >usbcore: registered new driver hub
> >ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 18
> >ehci_hcd 0000:02:07.2: EHCI Host Controller
> >ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1
> >ehci_hcd 0000:02:07.2: irq 18, io mem 0xd0208c00
> >ehci_hcd 0000:02:07.2: park 0
> >ehci_hcd 0000:02:07.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
> >2004
> >hub 1-0:1.0: USB hub found
> >hub 1-0:1.0: 5 ports detected
> >ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver
> >(PCI)
> >ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 18
> >ohci_hcd 0000:00:13.0: OHCI Host Controller
> >ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
> >ohci_hcd 0000:00:13.0: irq 18, io mem 0xd0001000
> >hub 2-0:1.0: USB hub found
> >hub 2-0:1.0: 3 ports detected
> >ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 18
> >ohci_hcd 0000:00:13.1: OHCI Host Controller
> >ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
> >ohci_hcd 0000:00:13.1: irq 18, io mem 0xd0002000
> >hub 3-0:1.0: USB hub found
> >hub 3-0:1.0: 3 ports detected
> >ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 17
> >ohci_hcd 0000:02:07.0: OHCI Host Controller
> >ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4
> >ohci_hcd 0000:02:07.0: irq 17, io mem 0xd0206000
> >hub 4-0:1.0: USB hub found
> >hub 4-0:1.0: 3 ports detected
> >ACPI: PCI Interrupt 0000:02:07.1[B] -> GSI 18 (level, low) -> IRQ 19
> >ohci_hcd 0000:02:07.1: OHCI Host Controller
> >ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5
> >ohci_hcd 0000:02:07.1: irq 19, io mem 0xd0207000
> >hub 5-0:1.0: USB hub found
> >hub 5-0:1.0: 2 ports detected
> >usb 4-1: new low speed USB device using ohci_hcd and address 2
> >ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16
> >Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
> >Yenta: Enabling burst memory read transactions
> >Yenta: Using CSCINT to route CSC interrupts to PCI
> >Yenta: Routing CardBus interrupts to PCI
> >Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
> >Yenta: ISA IRQ mask 0x0ed8, PCI irq 16
> >Socket status: 30000086
> >pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
> >pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
> >pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff
> >ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 17
> >Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
> >Yenta: Using CSCINT to route CSC interrupts to PCI
> >Yenta: Routing CardBus interrupts to PCI
> >Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
> >input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-1
> >usbcore: registered new driver usbhid
> >drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> >Yenta: ISA IRQ mask 0x0ed8, PCI irq 17
> >Socket status: 30000006
> >pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
> >pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
> >pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff
> >ieee1394: Initialized config rom entry `ip1394'
> >ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
> >ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17
> >ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17]
> >MMIO=[d0208000-d02087ff]  Max Packet=[2048]
> >ieee1394: Host added: ID:BUS[0-00:1023]  GUID[463f02005c594058]
> >eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
> >eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
> >Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
> >disabled
> >ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5
> >ACPI: PCI interrupt for device 0000:00:14.6 disabled
> >ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5
> >agpgart: Detected Ati IGP9100/M chipset
> >agpgart: AGP aperture is 32M @ 0xd2000000
> >USB Universal Host Controller Interface driver v2.3
> >ip_tables: (C) 2000-2002 Netfilter core team
> >ip_conntrack version 2.3 (7168 buckets, 57344 max) - 236 bytes per
> >conntrack
> >Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> >NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
> >directory
> >NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
> >NFSD: starting 90-second grace period
> >nfsd: last server has exited
> >nfsd: unexporting all filesystems
> >NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
> >directory
> >NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
> >NFSD: starting 90-second grace period
> >
> >Hope this helps.
> >
> >David
> >
> >
> >On Sun, 2005-10-30 at 10:33 -0500, Mark Hahn wrote:
> >  
> >
> >>>The problem I reported on the linux-kernel list and later here.  See
> >>>      
> >>>
> >>you mentioned posting the full dmesg(s).  in particular,
> >>are there differences in /proc/interrupts in working and 
> >>non-working kernels?  lspci -v might also be interesting.
> >>
> >>    
> >>
> >>>laptop has a P4 Hyperthreaded chip (someone mentioned that there was an
> >>>ACPI problem related to hyperthreading).
> >>>      
> >>>
> >>conceivable, but HT is hardly a new phenomenon.
> >>
> >>
> >>    
> >>
> >
> >-
> >To unsubscribe from this list: send the line "unsubscribe linux-ide" in
> >the body of a message to majordomo@vger.kernel.org
> >More majordomo info at  http://vger.kernel.org/majordomo-info.html
> >
> >  
> >
> 
> 
> 	
> 
> 	
> 		
> ___________________________________________________________ 
> Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de
> 


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-10-30 23:08     ` David Ronis
@ 2005-10-30 23:38       ` Stefan
  2005-10-31 19:02         ` David Ronis
  0 siblings, 1 reply; 13+ messages in thread
From: Stefan @ 2005-10-30 23:38 UTC (permalink / raw)
  To: David.Ronis; +Cc: Mark Hahn, linux-ide

David Ronis wrote:

>Hi Stefan,
>
>The lspci -v output is in the email I sent to Mark (and cc'd the list).
>  
>

Ah I missed that, just took a peek at the irqs

Can you try to unload those modules for the pccard stuff and usb and
then check if that makes any difference?
I have the feeling, your problem is caused by some other modules.

>I diff'ed the output, and there are lots of differences; most seem
>trivial (addresses & IRQ's).   As to switching to the lower modes I'll
>try (maybe later tonight).
>  
>

>Thanks for your help.
>
>David
>
>
>  
>
>>
>>    
>>
>
>
>  
>

___________________________________________________________ 
Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-10-30 23:38       ` Stefan
@ 2005-10-31 19:02         ` David Ronis
  2005-11-10 13:34           ` Bartlomiej Zolnierkiewicz
  0 siblings, 1 reply; 13+ messages in thread
From: David Ronis @ 2005-10-31 19:02 UTC (permalink / raw)
  To: Stefan; +Cc: David.Ronis, Mark Hahn, linux-ide

Hi Stefan,

I tried removing the modules you suggested and reran hdparm -tT /dev/hda
after each.  No difference.  I also played a bit more by going to
single-user mode and killing off various things (like udevd).   I turned
off networking and removed the ethernet driver--still no change.  What
seemed to make a difference was to turn of the firewall and remove all
the ipt_ drivers, although the performance was still about 4 times less
than what I get with the 2.6.13.6 kernel.  

Anyhow here are the results for the modules you asked about:

David
removing module yenta_socket

Module                  Size  Used by
autofs4                19972  1 
snd_pcm_oss            53664  0 
snd_mixer_oss          19328  1 snd_pcm_oss
nfsd                  227680  8 
exportfs                6528  1 nfsd
lockd                  62728  2 nfsd
sunrpc                144828  2 nfsd,lockd
ipt_limit               2688  1 
ipt_LOG                 7296  2 
ipt_state               2176  4 
ip_conntrack           49244  1 ipt_state
iptable_filter          3200  1 
ip_tables              21504  4
ipt_limit,ipt_LOG,ipt_state,iptable_filter
uhci_hcd               33296  0 
ati_agp                 9100  1 
snd_atiixp             21600  0 
snd_ac97_codec         94716  1 snd_atiixp
snd_ac97_bus            2432  1 snd_ac97_codec
snd_pcm                90884  3 snd_pcm_oss,snd_atiixp,snd_ac97_codec
snd_timer              25604  1 snd_pcm
snd                    56164  6
snd_pcm_oss,snd_mixer_oss,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc         11016  2 snd_atiixp,snd_pcm
8250_pci               19712  0 
eth1394                21128  0 
8250                   25076  1 8250_pci
serial_core            22016  1 8250
ohci1394               36276  0 
ieee1394               99896  2 eth1394,ohci1394
usbhid                 31236  0 
ohci_hcd               21892  0 
ehci_hcd               35592  0 
usbcore               121728  5 uhci_hcd,usbhid,ohci_hcd,ehci_hcd
8139too                27008  0 
mii                     5632  1 8139too
crc32                   4608  1 8139too
agpgart                35020  1 ati_agp


/dev/hda:
 Timing cached reads:    76 MB in  2.32 seconds =  32.78 MB/sec
 Timing buffered disk reads:   18 MB in  3.12 seconds =   5.76 MB/sec
removing module usbhid

Module                  Size  Used by
autofs4                19972  1 
snd_pcm_oss            53664  0 
snd_mixer_oss          19328  1 snd_pcm_oss
nfsd                  227680  8 
exportfs                6528  1 nfsd
lockd                  62728  2 nfsd
sunrpc                144828  2 nfsd,lockd
ipt_limit               2688  1 
ipt_LOG                 7296  2 
ipt_state               2176  4 
ip_conntrack           49244  1 ipt_state
iptable_filter          3200  1 
ip_tables              21504  4
ipt_limit,ipt_LOG,ipt_state,iptable_filter
uhci_hcd               33296  0 
ati_agp                 9100  1 
snd_atiixp             21600  0 
snd_ac97_codec         94716  1 snd_atiixp
snd_ac97_bus            2432  1 snd_ac97_codec
snd_pcm                90884  3 snd_pcm_oss,snd_atiixp,snd_ac97_codec
snd_timer              25604  1 snd_pcm
snd                    56164  6
snd_pcm_oss,snd_mixer_oss,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc         11016  2 snd_atiixp,snd_pcm
8250_pci               19712  0 
eth1394                21128  0 
8250                   25076  1 8250_pci
serial_core            22016  1 8250
ohci1394               36276  0 
ieee1394               99896  2 eth1394,ohci1394
ohci_hcd               21892  0 
ehci_hcd               35592  0 
usbcore               121728  4 uhci_hcd,ohci_hcd,ehci_hcd
8139too                27008  0 
mii                     5632  1 8139too
crc32                   4608  1 8139too
agpgart                35020  1 ati_agp


/dev/hda:
 Timing cached reads:    24 MB in  2.10 seconds =  11.41 MB/sec
 Timing buffered disk reads:   40 MB in  3.06 seconds =  13.07 MB/sec
removing module ohci_hcd

Module                  Size  Used by
autofs4                19972  1 
snd_pcm_oss            53664  0 
snd_mixer_oss          19328  1 snd_pcm_oss
nfsd                  227680  8 
exportfs                6528  1 nfsd
lockd                  62728  2 nfsd
sunrpc                144828  2 nfsd,lockd
ipt_limit               2688  1 
ipt_LOG                 7296  2 
ipt_state               2176  4 
ip_conntrack           49244  1 ipt_state
iptable_filter          3200  1 
ip_tables              21504  4
ipt_limit,ipt_LOG,ipt_state,iptable_filter
uhci_hcd               33296  0 
ati_agp                 9100  1 
snd_atiixp             21600  0 
snd_ac97_codec         94716  1 snd_atiixp
snd_ac97_bus            2432  1 snd_ac97_codec
snd_pcm                90884  3 snd_pcm_oss,snd_atiixp,snd_ac97_codec
snd_timer              25604  1 snd_pcm
snd                    56164  6
snd_pcm_oss,snd_mixer_oss,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc         11016  2 snd_atiixp,snd_pcm
8250_pci               19712  0 
eth1394                21128  0 
8250                   25076  1 8250_pci
serial_core            22016  1 8250
ohci1394               36276  0 
ieee1394               99896  2 eth1394,ohci1394
ehci_hcd               35592  0 
usbcore               121728  3 uhci_hcd,ehci_hcd
8139too                27008  0 
mii                     5632  1 8139too
crc32                   4608  1 8139too
agpgart                35020  1 ati_agp


/dev/hda:
 Timing cached reads:    28 MB in  2.13 seconds =  13.14 MB/sec
 Timing buffered disk reads:   30 MB in  3.02 seconds =   9.95 MB/sec
removing module ehci_hcd

Module                  Size  Used by
autofs4                19972  1 
snd_pcm_oss            53664  0 
snd_mixer_oss          19328  1 snd_pcm_oss
nfsd                  227680  8 
exportfs                6528  1 nfsd
lockd                  62728  2 nfsd
sunrpc                144828  2 nfsd,lockd
ipt_limit               2688  1 
ipt_LOG                 7296  2 
ipt_state               2176  4 
ip_conntrack           49244  1 ipt_state
iptable_filter          3200  1 
ip_tables              21504  4
ipt_limit,ipt_LOG,ipt_state,iptable_filter
uhci_hcd               33296  0 
ati_agp                 9100  1 
snd_atiixp             21600  0 
snd_ac97_codec         94716  1 snd_atiixp
snd_ac97_bus            2432  1 snd_ac97_codec
snd_pcm                90884  3 snd_pcm_oss,snd_atiixp,snd_ac97_codec
snd_timer              25604  1 snd_pcm
snd                    56164  6
snd_pcm_oss,snd_mixer_oss,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc         11016  2 snd_atiixp,snd_pcm
8250_pci               19712  0 
eth1394                21128  0 
8250                   25076  1 8250_pci
serial_core            22016  1 8250
ohci1394               36276  0 
ieee1394               99896  2 eth1394,ohci1394
usbcore               121728  2 uhci_hcd
8139too                27008  0 
mii                     5632  1 8139too
crc32                   4608  1 8139too
agpgart                35020  1 ati_agp


/dev/hda:
 Timing cached reads:    28 MB in  2.04 seconds =  13.75 MB/sec
 Timing buffered disk reads:   20 MB in  3.26 seconds =   6.14 MB/sec
removing module uhci_hcd

Module                  Size  Used by
autofs4                19972  1 
snd_pcm_oss            53664  0 
snd_mixer_oss          19328  1 snd_pcm_oss
nfsd                  227680  8 
exportfs                6528  1 nfsd
lockd                  62728  2 nfsd
sunrpc                144828  2 nfsd,lockd
ipt_limit               2688  1 
ipt_LOG                 7296  2 
ipt_state               2176  4 
ip_conntrack           49244  1 ipt_state
iptable_filter          3200  1 
ip_tables              21504  4
ipt_limit,ipt_LOG,ipt_state,iptable_filter
ati_agp                 9100  1 
snd_atiixp             21600  0 
snd_ac97_codec         94716  1 snd_atiixp
snd_ac97_bus            2432  1 snd_ac97_codec
snd_pcm                90884  3 snd_pcm_oss,snd_atiixp,snd_ac97_codec
snd_timer              25604  1 snd_pcm
snd                    56164  6
snd_pcm_oss,snd_mixer_oss,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc         11016  2 snd_atiixp,snd_pcm
8250_pci               19712  0 
eth1394                21128  0 
8250                   25076  1 8250_pci
serial_core            22016  1 8250
ohci1394               36276  0 
ieee1394               99896  2 eth1394,ohci1394
usbcore               121728  1 
8139too                27008  0 
mii                     5632  1 8139too
crc32                   4608  1 8139too
agpgart                35020  1 ati_agp


/dev/hda:
 Timing cached reads:    56 MB in  2.01 seconds =  27.92 MB/sec
 Timing buffered disk reads:   16 MB in  3.26 seconds =   4.90 MB/sec



On Mon, 2005-10-31 at 00:38 +0100, Stefan wrote:
> David Ronis wrote:
> 
> >Hi Stefan,
> >
> >The lspci -v output is in the email I sent to Mark (and cc'd the list).
> >  
> >
> 
> Ah I missed that, just took a peek at the irqs
> 
> Can you try to unload those modules for the pccard stuff and usb and
> then check if that makes any difference?
> I have the feeling, your problem is caused by some other modules.
> 
> >I diff'ed the output, and there are lots of differences; most seem
> >trivial (addresses & IRQ's).   As to switching to the lower modes I'll
> >try (maybe later tonight).
> >  
> >
> 
> 
> >Thanks for your help.
> >
> >David
> >
> >
> >  
> >
> >>
> >>    
> >>
> >
> >
> >  
> >
> 
> 
> 	
> 
> 	
> 		
> ___________________________________________________________ 
> Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de
> 


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-10-31 19:02         ` David Ronis
@ 2005-11-10 13:34           ` Bartlomiej Zolnierkiewicz
  2005-11-10 16:59             ` Stefan
  0 siblings, 1 reply; 13+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2005-11-10 13:34 UTC (permalink / raw)
  To: David.Ronis; +Cc: Stefan, Mark Hahn, linux-ide

I would suggest doing binary search on -rc and snapshot releases.

http://kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.14-rc*
http://kernel.org/pub/linux/kernel/v2.6/snapshots/old/patch-2.6.14-*

Otherwise we can only guess what is wrong.

Moreover it doesn't look like an IDE problem the real performance
regression is in cached reads not the buffered ones.

On 10/31/05, David Ronis <ronis@ronispc.chem.mcgill.ca> wrote:
> Hi Stefan,
>
> I tried removing the modules you suggested and reran hdparm -tT /dev/hda
> after each.  No difference.  I also played a bit more by going to
> single-user mode and killing off various things (like udevd).   I turned
> off networking and removed the ethernet driver--still no change.  What
> seemed to make a difference was to turn of the firewall and remove all
> the ipt_ drivers, although the performance was still about 4 times less
> than what I get with the 2.6.13.6 kernel.

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: Serious IDE problem still present in 2.6.14
  2005-11-10 13:34           ` Bartlomiej Zolnierkiewicz
@ 2005-11-10 16:59             ` Stefan
  0 siblings, 0 replies; 13+ messages in thread
From: Stefan @ 2005-11-10 16:59 UTC (permalink / raw)
  To: Bartlomiej Zolnierkiewicz; +Cc: David.Ronis, Mark Hahn, linux-ide

Bartlomiej Zolnierkiewicz wrote:

>I would suggest doing binary search on -rc and snapshot releases.
>
>http://kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.14-rc*
>http://kernel.org/pub/linux/kernel/v2.6/snapshots/old/patch-2.6.14-*
>
>Otherwise we can only guess what is wrong.
>
>Moreover it doesn't look like an IDE problem the real performance
>regression is in cached reads not the buffered ones.
>  
>
Exactly, that's why I advised him to send another mail to the
linux-kernel list,
since I think it is related to some of the acpi changes from 2.6.12 to
>=2.6.13.
If he switches off acpi then performance is back to normal and since
there were basically no changes in the ide code
or code for his controller it must be related to other changes.

>On 10/31/05, David Ronis <ronis@ronispc.chem.mcgill.ca> wrote:
>  
>
>>Hi Stefan,
>>
>>I tried removing the modules you suggested and reran hdparm -tT /dev/hda
>>after each.  No difference.  I also played a bit more by going to
>>single-user mode and killing off various things (like udevd).   I turned
>>off networking and removed the ethernet driver--still no change.  What
>>seemed to make a difference was to turn of the firewall and remove all
>>the ipt_ drivers, although the performance was still about 4 times less
>>than what I get with the 2.6.13.6 kernel.
>>    
>>
>
>  
>


	

	
		
___________________________________________________________ 
Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de


^ permalink raw reply	[flat|nested] 13+ messages in thread

end of thread, other threads:[~2005-11-10 17:00 UTC | newest]

Thread overview: 13+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-10-30  0:48 Serious IDE problem still present in 2.6.14 David Ronis
2005-10-30  2:15 ` Stefan
2005-10-30  3:13   ` David Ronis
2005-10-30  8:53     ` Stefan
2005-10-30 15:52       ` David Ronis
     [not found] <Pine.LNX.4.44.0510301030120.26176-100000@coffee.psychology.mcmaster.ca>
2005-10-30 16:31 ` David Ronis
2005-10-30 18:57   ` Stefan
2005-10-30 23:02   ` Stefan
2005-10-30 23:08     ` David Ronis
2005-10-30 23:38       ` Stefan
2005-10-31 19:02         ` David Ronis
2005-11-10 13:34           ` Bartlomiej Zolnierkiewicz
2005-11-10 16:59             ` Stefan

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).