From mboxrd@z Thu Jan 1 00:00:00 1970 From: Stefan Subject: Re: Serious IDE problem still present in 2.6.14 Date: Mon, 31 Oct 2005 00:02:52 +0100 Message-ID: <4365511C.7040903@yahoo.de> References: <1130689871.6348.3.camel@montroll.chem.mcgill.ca> Mime-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit Return-path: Received: from smtp018.mail.yahoo.com ([216.136.174.115]:31859 "HELO smtp018.mail.yahoo.com") by vger.kernel.org with SMTP id S932387AbVJ3XC5 (ORCPT ); Sun, 30 Oct 2005 18:02:57 -0500 In-Reply-To: <1130689871.6348.3.camel@montroll.chem.mcgill.ca> Sender: linux-ide-owner@vger.kernel.org List-Id: linux-ide@vger.kernel.org To: David.Ronis@mcgill.ca Cc: Mark Hahn , linux-ide@vger.kernel.org David Ronis wrote: Hi David, I just checked the diffs of ide and atiixp from 2.6.12.6 to 2.6.14, I don't think those changes caused the problem. Can you provide some more info? I would like to see if there are differences in lspci -v output of your old and your new kernel. Also could you check if it makes any difference if you switch down to udma4 udma2 and then test speeds? >Hi Mark, > >I've copied the information you wanted below. > >First in 2.6.12.6: > >cat /proc/interrupts > CPU0 CPU1 > 0: 53375 1 IO-APIC-edge timer > 1: 47 2 IO-APIC-edge i8042 > 5: 1 0 IO-APIC-level ATI IXP > 8: 1 0 IO-APIC-edge rtc > 12: 127 0 IO-APIC-edge i8042 > 14: 4970 0 IO-APIC-edge ide0 > 15: 0 0 IO-APIC-edge ide1 > 16: 28 0 IO-APIC-level ohci_hcd:usb4, yenta, >ohci1394 > 17: 1 0 IO-APIC-level yenta > 18: 0 0 IO-APIC-level ohci_hcd:usb5 > 19: 2 0 IO-APIC-level eth0, ehci_hcd:usb1, >ohci_hcd:usb2, ohci_hcd:usb3 > 21: 43 0 IO-APIC-level acpi >NMI: 0 0 >LOC: 53271 53277 >ERR: 0 >MIS: 0 > >lspci -v >00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge >(rev 02) > Subsystem: ATI Technologies Inc: Unknown device 1234 > Flags: bus master, 66Mhz, medium devsel, latency 64 > Memory at d2000000 (32-bit, prefetchable) [size=32M] > Memory at d0000000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [a0] AGP version 3.0 > >00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge >(prog-if 00 [Normal decode]) > Flags: bus master, 66Mhz, medium devsel, latency 99 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=68 > I/O behind bridge: 00009000-00009fff > Memory behind bridge: d0100000-d01fffff > Prefetchable memory behind bridge: e0000000-efffffff > >00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev >01) (prog-if 10 [OHCI]) > Subsystem: ATI Technologies Inc: Unknown device 434c > Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 19 > Memory at d0001000 (32-bit, non-prefetchable) [size=4K] > >00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev >01) (prog-if 10 [OHCI]) > Subsystem: ATI Technologies Inc: Unknown device 434c > Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 19 > Memory at d0002000 (32-bit, non-prefetchable) [size=4K] > >00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: 66Mhz, medium devsel > I/O ports at 8040 [size=16] > Memory at 58000000 (32-bit, non-prefetchable) [size=1K] > >00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master >PCI IDE Controller (prog-if 8a [Master SecP PriP]) > Subsystem: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE >Controller > Flags: bus master, medium devsel, latency 64, IRQ 16 > I/O ports at > I/O ports at > I/O ports at > I/O ports at > I/O ports at 8060 [size=16] > >00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c > Subsystem: ATI Technologies Inc: Unknown device 434c > Flags: bus master, 66Mhz, medium devsel, latency 0 > >00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if >01 [Subtractive decode]) > Flags: bus master, 66Mhz, medium devsel, latency 64 > Bus: primary=00, secondary=02, subordinate=04, sec-latency=69 > I/O behind bridge: 0000a000-0000afff > Memory behind bridge: d0200000-d02fffff > >00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 >Audio Controller > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, 66Mhz, slow devsel, latency 64, IRQ 5 > Memory at d0003000 (32-bit, non-prefetchable) [size=256] > >00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00 >[Generic]) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: 66Mhz, slow devsel, IRQ 5 > Memory at d0003400 (32-bit, non-prefetchable) [size=256] > >01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP >[Radeon Mobility 9100IGP] (prog-if 00 [VGA]) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 66, >IRQ 10 > Memory at e0000000 (32-bit, prefetchable) [size=256M] > I/O ports at 9000 [size=256] > Memory at d0100000 (32-bit, non-prefetchable) [size=64K] > Expansion ROM at [disabled] [size=128K] > Capabilities: [58] AGP version 3.0 > Capabilities: [50] Power Management version 2 > >02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 >IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI]) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, medium devsel, latency 64, IRQ 16 > Memory at d0208000 (32-bit, non-prefetchable) [size=2K] > Memory at d0200000 (32-bit, non-prefetchable) [size=16K] > Capabilities: [44] Power Management version 2 > >02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g >Wireless LAN Controller (rev 03) > Subsystem: Hewlett-Packard Company: Unknown device 12f4 > Flags: bus master, fast devsel, latency 64, IRQ 5 > Memory at d0204000 (32-bit, non-prefetchable) [size=8K] > >02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. >RTL-8139/8139C/8139C+ (rev 10) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, medium devsel, latency 128, IRQ 19 > I/O ports at a000 [size=256] > Memory at d0208800 (32-bit, non-prefetchable) [size=256] > Capabilities: [50] Power Management version 2 > >02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller >(rev 01) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, medium devsel, latency 168, IRQ 17 > Memory at 58001000 (32-bit, non-prefetchable) [size=4K] > Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 > Memory window 0: 58400000-587ff000 (prefetchable) > Memory window 1: 58800000-58bff000 > I/O window 0: 00004000-000040ff > I/O window 1: 00004400-000044ff > 16-bit legacy interface ports at 0001 > >02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller >(rev 01) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, medium devsel, latency 168, IRQ 16 > Memory at 58002000 (32-bit, non-prefetchable) [size=4K] > Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176 > Memory window 0: 58c00000-58fff000 (prefetchable) > Memory window 1: 59000000-593ff000 > I/O window 0: 00004800-000048ff > I/O window 1: 00004c00-00004cff > 16-bit legacy interface ports at 0001 > >02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading >Function (rev 01) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, medium devsel, latency 64 > I/O ports at a400 [size=64] > Capabilities: [44] Power Management version 2 > >02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI]) > Subsystem: NEC Corporation USB > Flags: bus master, medium devsel, latency 64, IRQ 16 > Memory at d0206000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [40] Power Management version 2 > >02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI]) > Subsystem: NEC Corporation USB > Flags: bus master, medium devsel, latency 64, IRQ 18 > Memory at d0207000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [40] Power Management version 2 > >02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 >[EHCI]) > Subsystem: NEC Corporation USB 2.0 > Flags: bus master, medium devsel, latency 64, IRQ 19 > Memory at d0208c00 (32-bit, non-prefetchable) [size=256] > Capabilities: [40] Power Management version 2 > > >dmesg >Linux version 2.6.12.6 (root@montroll.lan) (gcc version 3.4.4) #4 SMP >Tue Aug 30 20:38:22 EDT 2005 >BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved) > BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 0000000047f70000 (usable) > BIOS-e820: 0000000047f70000 - 0000000047f7d000 (ACPI data) > BIOS-e820: 0000000047f7d000 - 0000000047f80000 (ACPI NVS) > BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved) > BIOS-e820: 0000000057f80000 - 0000000058000000 (reserved) > BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) >Warning only 896MB will be used. >Use a HIGHMEM enabled kernel. >896MB LOWMEM available. >found SMP MP-table at 000f6570 >On node 0 totalpages: 229376 > DMA zone: 4096 pages, LIFO batch:1 > Normal zone: 225280 pages, LIFO batch:31 > HighMem zone: 0 pages, LIFO batch:1 >DMI present. >ACPI: RSDP (v000 PTLTD ) @ 0x000f6600 >ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ >0x47f791c8 >ACPI: FADT (v001 HP Chinook 0x06040000 ATI 0x000f4240) @ >0x47f7ceed >ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ >0x47f7cf61 >ACPI: SSDT (v001 PTLTD ACPIHT 0x06040000 LTP 0x00000001) @ >0x47f7cfc9 >ACPI: DSDT (v001 HP SB200 0x06040000 INTL 0x20030509) @ >0x00000000 >ACPI: PM-Timer IO Port: 0x8008 >ACPI: Local APIC address 0xfee00000 >ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) >Processor #0 15:2 APIC version 20 >ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) >Processor #1 15:2 APIC version 20 >ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) >ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) >ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) >IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 >ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) >ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) >ACPI: IRQ0 used by override. >ACPI: IRQ2 used by override. >Enabling APIC mode: Flat. Using 1 I/O APICs >Using ACPI (MADT) for SMP configuration information >Allocating PCI resources starting at 58000000 (gap: 58000000:a6c00000) >Built 1 zonelists >Kernel command line: BOOT_IMAGE=2.6.12.6 ro root=302 >mapped APIC to ffffd000 (fee00000) >mapped IOAPIC to ffffc000 (fec00000) >Initializing CPU#0 >PID hash table entries: 4096 (order: 12, 65536 bytes) >Detected 3000.728 MHz processor. >Using pmtmr for high-res timesource >Console: colour VGA+ 80x25 >Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) >Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) >Memory: 906084k/917504k available (1695k kernel code, 10908k reserved, >737k data, 192k init, 0k highmem) >Checking if this processor honours the WP bit even in supervisor mode... >Ok. >Calibrating delay loop... 5963.77 BogoMIPS (lpj=2981888) >Mount-cache hash table entries: 512 >CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 >00004400 00000000 00000000 >CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 >00004400 00000000 00000000 >CPU: Trace cache: 12K uops, L1 D cache: 8K >CPU: L2 cache: 512K >CPU: Physical Processor ID: 0 >CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 >00000000 00000000 >Intel machine check architecture supported. >Intel machine check reporting enabled on CPU#0. >CPU0: Intel P4/Xeon Extended MCE MSRs (12) available >CPU0: Thermal monitoring enabled >Enabling fast FPU save and restore... done. >Enabling unmasked SIMD FPU exception support... done. >Checking 'hlt' instruction... OK. >CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09 >Booting processor 1/1 eip 3000 >Initializing CPU#1 >Calibrating delay loop... 5996.54 BogoMIPS (lpj=2998272) >CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 >00004400 00000000 00000000 >CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 >00004400 00000000 00000000 >CPU: Trace cache: 12K uops, L1 D cache: 8K >CPU: L2 cache: 512K >CPU: Physical Processor ID: 0 >CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 >00000000 00000000 >Intel machine check architecture supported. >Intel machine check reporting enabled on CPU#1. >CPU1: Intel P4/Xeon Extended MCE MSRs (12) available >CPU1: Thermal monitoring enabled >CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09 >Total of 2 processors activated (11960.32 BogoMIPS). >ENABLING IO-APIC IRQs >..TIMER: vector=0x31 pin1=2 pin2=-1 >checking TSC synchronization across 2 CPUs: passed. >Brought up 2 CPUs >CPU0 attaching sched-domain: > domain 0: span 3 > groups: 1 2 > domain 1: span 3 > groups: 3 >CPU1 attaching sched-domain: > domain 0: span 3 > groups: 2 1 > domain 1: span 3 > groups: 3 >NET: Registered protocol family 16 >PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2 >PCI: Using configuration type 1 >mtrr: v2.0 (20020519) >ACPI: Subsystem revision 20050309 >ACPI: Interpreter enabled >ACPI: Using IOAPIC for interrupt routing >ACPI: PCI Root Bridge [PCI0] (0000:00) >PCI: Probing PCI hardware (bus 00) >PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 >Boot video device is 0000:01:05.0 >PCI: Transparent bridge - 0000:00:14.4 >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] >ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled. >ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled. >ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled. >ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled. >ACPI: Embedded Controller [EC0] (gpe 6) >PCI: Using ACPI for IRQ routing >PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a >report >Machine check exception polling timer started. >Initializing Cryptographic API >ACPI: AC Adapter [ACAD] (on-line) >ACPI: Battery Slot [BAT1] (battery present) >ACPI: Power Button (FF) [PWRF] >ACPI: Lid Switch [LID] >ACPI: Thermal Zone [THRM] (52 C) >Real Time Clock Driver v1.12 >i8042.c: Detected active multiplexing controller, rev 1.1. >serio: i8042 AUX0 port at 0x60,0x64 irq 12 >serio: i8042 AUX1 port at 0x60,0x64 irq 12 >serio: i8042 AUX2 port at 0x60,0x64 irq 12 >serio: i8042 AUX3 port at 0x60,0x64 irq 12 >serio: i8042 KBD port at 0x60,0x64 irq 1 >io scheduler noop registered >io scheduler anticipatory registered >io scheduler deadline registered >io scheduler cfq registered >Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 >ide: Assuming 33MHz system bus speed for PIO modes; override with >idebus=xx >ATIIXP: IDE controller at PCI slot 0000:00:14.1 >ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 >ATIIXP: chipset revision 0 >ATIIXP: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio >Probing IDE interface ide0... >hda: ST9100823A, ATA DISK drive >ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 >Probing IDE interface ide1... >hdc: SD-R2512, ATAPI CD/DVD-ROM drive >ide1 at 0x170-0x177,0x376 on irq 15 >Probing IDE interface ide2... >Probing IDE interface ide3... >Probing IDE interface ide4... >Probing IDE interface ide5... >hda: max request size: 128KiB >hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63, >UDMA(100) >hda: cache flushes supported > hda: hda1 hda2 >mice: PS/2 mouse device common for all mice >input: PC Speaker >NET: Registered protocol family 2 >IP: routing cache hash table of 4096 buckets, 64Kbytes >TCP established hash table entries: 131072 (order: 9, 2097152 bytes) >TCP bind hash table entries: 65536 (order: 7, 786432 bytes) >TCP: Hash tables configured (established 131072 bind 65536) >NET: Registered protocol family 1 >NET: Registered protocol family 15 >ACPI wakeup devices: >ELAN USB0 USB1 USB2 KBC0 MSE0 >ACPI: (supports S0 S3 S4 S5) >kjournald starting. Commit interval 5 seconds >EXT3-fs: mounted filesystem with ordered data mode. >VFS: Mounted root (ext3 filesystem) readonly. >Freeing unused kernel memory: 192k freed >input: AT Translated Set 2 keyboard on isa0060/serio0 >alps.c: Enabling hardware tapping >input: PS/2 Mouse on isa0060/serio4 >input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4 >Adding 977216k swap on /dev/hda1. Priority:-1 extents:1 >EXT3 FS on hda2, internal journal >Linux agpgart interface v0.101 (c) Dave Jones >8139too Fast Ethernet driver 0.9.27 >ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19 >eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:01:82:2d, IRQ 19 >eth0: Identified 8139 chip type 'RTL-8101' >eth0: link up, 10Mbps, half-duplex, lpa 0x0000 >usbcore: registered new driver usbfs >usbcore: registered new driver hub >ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 19 >ehci_hcd 0000:02:07.2: NEC Corporation USB 2.0 >ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1 >ehci_hcd 0000:02:07.2: irq 19, io mem 0xd0208c00 >ehci_hcd 0000:02:07.2: park 0 >ehci_hcd 0000:02:07.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec >2004 >hub 1-0:1.0: USB hub found >hub 1-0:1.0: 5 ports detected >ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) >ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19 >ohci_hcd 0000:00:13.0: ATI Technologies Inc OHCI USB Controller #1 >ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 >ohci_hcd 0000:00:13.0: irq 19, io mem 0xd0001000 >hub 2-0:1.0: USB hub found >hub 2-0:1.0: 3 ports detected >ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19 >ohci_hcd 0000:00:13.1: ATI Technologies Inc OHCI USB Controller #2 >ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 >ohci_hcd 0000:00:13.1: irq 19, io mem 0xd0002000 >hub 3-0:1.0: USB hub found >hub 3-0:1.0: 3 ports detected >ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 16 >ohci_hcd 0000:02:07.0: NEC Corporation USB >ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4 >ohci_hcd 0000:02:07.0: irq 16, io mem 0xd0206000 >hub 4-0:1.0: USB hub found >hub 4-0:1.0: 3 ports detected >ACPI: PCI Interrupt 0000:02:07.1[B] -> GSI 18 (level, low) -> IRQ 18 >ohci_hcd 0000:02:07.1: NEC Corporation USB (#2) >ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5 >ohci_hcd 0000:02:07.1: irq 18, io mem 0xd0207000 >hub 5-0:1.0: USB hub found >hub 5-0:1.0: 2 ports detected >usb 4-1: new low speed USB device using ohci_hcd and address 2 >Linux Kernel Card Services > options: [pci] [cardbus] [pm] >ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 17 >Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b] >Yenta: Enabling burst memory read transactions >Yenta: Using CSCINT to route CSC interrupts to PCI >Yenta: Routing CardBus interrupts to PCI >Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64 >Yenta: ISA IRQ mask 0x0ed8, PCI irq 17 >Socket status: 30000006 >ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 16 >Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b] >Yenta: Using CSCINT to route CSC interrupts to PCI >Yenta: Routing CardBus interrupts to PCI >Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64 >input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-1 >usbcore: registered new driver usbhid >drivers/usb/input/hid-core.c: v2.01:USB HID core driver >Yenta: ISA IRQ mask 0x0ed8, PCI irq 16 >Socket status: 30000006 >ieee1394: Initialized config rom entry `ip1394' >ohci1394: $Rev: 1250 $ Ben Collins >ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 >ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] >MMIO=[d0208000-d02087ff] Max Packet=[2048] >Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing >disabled >ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5 >ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5 >agpgart: Detected Ati IGP9100/M chipset >agpgart: AGP aperture is 32M @ 0xd2000000 >ieee1394: Host added: ID:BUS[0-00:1023] GUID[463f02005c594058] >eth1394: $Rev: 1247 $ Ben Collins >eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) >USB Universal Host Controller Interface driver v2.2 >ip_tables: (C) 2000-2002 Netfilter core team >ip_conntrack version 2.1 (7168 buckets, 57344 max) - 256 bytes per >conntrack >Installing knfsd (copyright (C) 1996 okir@monad.swb.de). > >Now in 2.6.14: > >cat /proc/interrupts > CPU0 CPU1 > 0: 345156 3 IO-APIC-edge timer > 1: 51 2 IO-APIC-edge i8042 > 5: 1 0 IO-APIC-level ATI IXP > 8: 1 0 IO-APIC-edge rtc > 12: 121 0 IO-APIC-edge i8042 > 14: 5474 0 IO-APIC-edge ide0 > 15: 0 0 IO-APIC-edge ide1 > 16: 1 0 IO-APIC-level yenta > 17: 29 0 IO-APIC-level ohci_hcd:usb4, yenta, >ohci1394 > 18: 2 0 IO-APIC-level eth0, ehci_hcd:usb1, >ohci_hcd:usb2, ohci_hcd:usb3 > 19: 0 0 IO-APIC-level ohci_hcd:usb5 > 21: 40 0 IO-APIC-level acpi >NMI: 0 0 >LOC: 345004 345037 >ERR: 0 >MIS: 0 > >lspci -v >00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge >(rev 02) > Subsystem: ATI Technologies Inc: Unknown device 1234 > Flags: bus master, 66Mhz, medium devsel, latency 64 > Memory at d2000000 (32-bit, prefetchable) [size=32M] > Memory at d0000000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [a0] AGP version 3.0 > >00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge >(prog-if 00 [Normal decode]) > Flags: bus master, 66Mhz, medium devsel, latency 99 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=68 > I/O behind bridge: 00009000-00009fff > Memory behind bridge: d0100000-d01fffff > Prefetchable memory behind bridge: e0000000-efffffff > >00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev >01) (prog-if 10 [OHCI]) > Subsystem: ATI Technologies Inc: Unknown device 434c > Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18 > Memory at d0001000 (32-bit, non-prefetchable) [size=4K] > >00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev >01) (prog-if 10 [OHCI]) > Subsystem: ATI Technologies Inc: Unknown device 434c > Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18 > Memory at d0002000 (32-bit, non-prefetchable) [size=4K] > >00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: 66Mhz, medium devsel > I/O ports at 8040 [size=16] > Memory at 64000000 (32-bit, non-prefetchable) [size=1K] > >00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master >PCI IDE Controller (prog-if 8a [Master SecP PriP]) > Subsystem: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE >Controller > Flags: bus master, medium devsel, latency 64, IRQ 17 > I/O ports at > I/O ports at > I/O ports at > I/O ports at > I/O ports at 8060 [size=16] > >00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c > Subsystem: ATI Technologies Inc: Unknown device 434c > Flags: bus master, 66Mhz, medium devsel, latency 0 > >00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if >01 [Subtractive decode]) > Flags: bus master, 66Mhz, medium devsel, latency 64 > Bus: primary=00, secondary=02, subordinate=04, sec-latency=69 > I/O behind bridge: 0000a000-0000afff > Memory behind bridge: d0200000-d02fffff > Prefetchable memory behind bridge: 60000000-63ffffff > >00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 >Audio Controller > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, 66Mhz, slow devsel, latency 64, IRQ 5 > Memory at d0003000 (32-bit, non-prefetchable) [size=256] > >00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00 >[Generic]) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: 66Mhz, slow devsel, IRQ 5 > Memory at d0003400 (32-bit, non-prefetchable) [size=256] > >01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP >[Radeon Mobility 9100IGP] (prog-if 00 [VGA]) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 66, >IRQ 10 > Memory at e0000000 (32-bit, prefetchable) [size=256M] > I/O ports at 9000 [size=256] > Memory at d0100000 (32-bit, non-prefetchable) [size=64K] > Expansion ROM at d0120000 [disabled] [size=128K] > Capabilities: [58] AGP version 3.0 > Capabilities: [50] Power Management version 2 > >02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 >IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI]) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, medium devsel, latency 64, IRQ 17 > Memory at d0208000 (32-bit, non-prefetchable) [size=2K] > Memory at d0200000 (32-bit, non-prefetchable) [size=16K] > Capabilities: [44] Power Management version 2 > >02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g >Wireless LAN Controller (rev 03) > Subsystem: Hewlett-Packard Company: Unknown device 12f4 > Flags: bus master, fast devsel, latency 64, IRQ 5 > Memory at d0204000 (32-bit, non-prefetchable) [size=8K] > >02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. >RTL-8139/8139C/8139C+ (rev 10) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, medium devsel, latency 128, IRQ 18 > I/O ports at a000 [size=256] > Memory at d0208800 (32-bit, non-prefetchable) [size=256] > Capabilities: [50] Power Management version 2 > >02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller >(rev 01) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, medium devsel, latency 168, IRQ 16 > Memory at d0209000 (32-bit, non-prefetchable) [size=4K] > Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 > Memory window 0: 60000000-61fff000 (prefetchable) > Memory window 1: 66000000-67fff000 > I/O window 0: 0000a800-0000a8ff > I/O window 1: 0000ac00-0000acff > 16-bit legacy interface ports at 0001 > >02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller >(rev 01) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, medium devsel, latency 168, IRQ 17 > Memory at d020a000 (32-bit, non-prefetchable) [size=4K] > Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176 > Memory window 0: 62000000-63fff000 (prefetchable) > Memory window 1: 68000000-69fff000 > I/O window 0: 00001400-000014ff > I/O window 1: 00001800-000018ff > 16-bit legacy interface ports at 0001 > >02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading >Function (rev 01) > Subsystem: Hewlett-Packard Company: Unknown device 006b > Flags: bus master, medium devsel, latency 64 > I/O ports at a400 [size=64] > Capabilities: [44] Power Management version 2 > >02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI]) > Subsystem: NEC Corporation USB > Flags: bus master, medium devsel, latency 64, IRQ 17 > Memory at d0206000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [40] Power Management version 2 > >02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI]) > Subsystem: NEC Corporation USB > Flags: bus master, medium devsel, latency 64, IRQ 19 > Memory at d0207000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [40] Power Management version 2 > >02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 >[EHCI]) > Subsystem: NEC Corporation USB 2.0 > Flags: bus master, medium devsel, latency 64, IRQ 18 > Memory at d0208c00 (32-bit, non-prefetchable) [size=256] > Capabilities: [40] Power Management version 2 > > >dmesg >Linux version 2.6.14 (root@montroll) (gcc version 4.0.2) #10 SMP Fri Oct >28 15:56:01 EDT 2005 >BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved) > BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 0000000047f70000 (usable) > BIOS-e820: 0000000047f70000 - 0000000047f7d000 (ACPI data) > BIOS-e820: 0000000047f7d000 - 0000000047f80000 (ACPI NVS) > BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved) > BIOS-e820: 0000000057f80000 - 0000000058000000 (reserved) > BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) >Warning only 896MB will be used. >Use a HIGHMEM enabled kernel. >896MB LOWMEM available. >found SMP MP-table at 000f6570 >On node 0 totalpages: 229376 > DMA zone: 4096 pages, LIFO batch:1 > Normal zone: 225280 pages, LIFO batch:31 > HighMem zone: 0 pages, LIFO batch:1 >DMI present. >ACPI: RSDP (v000 PTLTD ) @ 0x000f6600 >ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ >0x47f791c8 >ACPI: FADT (v001 HP Chinook 0x06040000 ATI 0x000f4240) @ >0x47f7ceed >ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ >0x47f7cf61 >ACPI: SSDT (v001 PTLTD ACPIHT 0x06040000 LTP 0x00000001) @ >0x47f7cfc9 >ACPI: DSDT (v001 HP SB200 0x06040000 INTL 0x20030509) @ >0x00000000 >ACPI: PM-Timer IO Port: 0x8008 >ACPI: Local APIC address 0xfee00000 >ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) >Processor #0 15:2 APIC version 20 >ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) >Processor #1 15:2 APIC version 20 >ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) >ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) >ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) >IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 >ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) >ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) >ACPI: IRQ0 used by override. >ACPI: IRQ2 used by override. >Enabling APIC mode: Flat. Using 1 I/O APICs >Using ACPI (MADT) for SMP configuration information >Allocating PCI resources starting at 60000000 (gap: 58000000:a6c00000) >Built 1 zonelists >Kernel command line: BOOT_IMAGE=2.6.14 ro root=302 >mapped APIC to ffffd000 (fee00000) >mapped IOAPIC to ffffc000 (fec00000) >Initializing CPU#0 >PID hash table entries: 4096 (order: 12, 65536 bytes) >Detected 3000.911 MHz processor. >Using pmtmr for high-res timesource >Console: colour VGA+ 80x25 >Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) >Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) >Memory: 906284k/917504k available (1696k kernel code, 10708k reserved, >531k data, 188k init, 0k highmem) >Checking if this processor honours the WP bit even in supervisor mode... >Ok. >Calibrating delay using timer specific routine.. 6002.40 BogoMIPS >(lpj=3001201) >Mount-cache hash table entries: 512 >CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 >00004400 00000000 00000000 >CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 >00004400 00000000 00000000 >CPU: Trace cache: 12K uops, L1 D cache: 8K >CPU: L2 cache: 512K >CPU: Physical Processor ID: 0 >CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 >00000000 00000000 >Intel machine check architecture supported. >Intel machine check reporting enabled on CPU#0. >CPU0: Intel P4/Xeon Extended MCE MSRs (12) available >CPU0: Thermal monitoring enabled >mtrr: v2.0 (20020519) >Enabling fast FPU save and restore... done. >Enabling unmasked SIMD FPU exception support... done. >Checking 'hlt' instruction... OK. >CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09 >Booting processor 1/1 eip 2000 >Initializing CPU#1 >Calibrating delay using timer specific routine.. 5999.46 BogoMIPS >(lpj=2999730) >CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 >00004400 00000000 00000000 >CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 >00004400 00000000 00000000 >CPU: Trace cache: 12K uops, L1 D cache: 8K >CPU: L2 cache: 512K >CPU: Physical Processor ID: 0 >CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 >00000000 00000000 >Intel machine check architecture supported. >Intel machine check reporting enabled on CPU#1. >CPU1: Intel P4/Xeon Extended MCE MSRs (12) available >CPU1: Thermal monitoring enabled >CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09 >Total of 2 processors activated (12001.86 BogoMIPS). >ENABLING IO-APIC IRQs >..TIMER: vector=0x31 pin1=2 pin2=-1 >checking TSC synchronization across 2 CPUs: passed. >softlockup thread 0 started up. >Brought up 2 CPUs >softlockup thread 1 started up. >NET: Registered protocol family 16 >ACPI: bus type pci registered >PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2 >PCI: Using configuration type 1 >ACPI: Subsystem revision 20050902 >ACPI: Interpreter enabled >ACPI: Using IOAPIC for interrupt routing >ACPI: PCI Root Bridge [PCI0] (0000:00) >PCI: Probing PCI hardware (bus 00) >ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 >PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 >Boot video device is 0000:01:05.0 >PCI: Transparent bridge - 0000:00:14.4 >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] >ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled. >ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled. >ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled. >ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled. >ACPI: Embedded Controller [EC0] (gpe 6) >PCI: Using ACPI for IRQ routing >PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a >report >PCI: Bridge: 0000:00:01.0 > IO window: 9000-9fff > MEM window: d0100000-d01fffff > PREFETCH window: e0000000-efffffff >PCI: Bus 3, cardbus bridge: 0000:02:04.0 > IO window: 0000a800-0000a8ff > IO window: 0000ac00-0000acff > PREFETCH window: 60000000-61ffffff > MEM window: 66000000-67ffffff >PCI: Bus 7, cardbus bridge: 0000:02:04.1 > IO window: 00001400-000014ff > IO window: 00001800-000018ff > PREFETCH window: 62000000-63ffffff > MEM window: 68000000-69ffffff >PCI: Bridge: 0000:00:14.4 > IO window: a000-afff > MEM window: d0200000-d02fffff > PREFETCH window: 60000000-63ffffff >ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16 >ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 17 >Machine check exception polling timer started. >Initializing Cryptographic API >ACPI: AC Adapter [ACAD] (on-line) >ACPI: Battery Slot [BAT1] (battery present) >ACPI: Power Button (FF) [PWRF] >ACPI: Lid Switch [LID] >ACPI: Power Button (CM) [PWRB] >ACPI: CPU0 (power states: C1[C1] C2[C2]) >ACPI: CPU1 (power states: C1[C1] C2[C2]) >ACPI: Thermal Zone [THRM] (52 C) >Real Time Clock Driver v1.12 >i8042.c: Detected active multiplexing controller, rev 1.1. >serio: i8042 AUX0 port at 0x60,0x64 irq 12 >serio: i8042 AUX1 port at 0x60,0x64 irq 12 >serio: i8042 AUX2 port at 0x60,0x64 irq 12 >serio: i8042 AUX3 port at 0x60,0x64 irq 12 >serio: i8042 KBD port at 0x60,0x64 irq 1 >io scheduler noop registered >io scheduler anticipatory registered >io scheduler deadline registered >io scheduler cfq registered >Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 >ide: Assuming 33MHz system bus speed for PIO modes; override with >idebus=xx >ATIIXP: IDE controller at PCI slot 0000:00:14.1 >ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17 >ATIIXP: chipset revision 0 >ATIIXP: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio >Probing IDE interface ide0... >hda: ST9100823A, ATA DISK drive >ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 >Probing IDE interface ide1... >hdc: SD-R2512, ATAPI CD/DVD-ROM drive >ide1 at 0x170-0x177,0x376 on irq 15 >hda: max request size: 128KiB >hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63, >UDMA(100) >hda: cache flushes supported > hda: hda1 hda2 >mice: PS/2 mouse device common for all mice >input: PC Speaker >NET: Registered protocol family 2 >IP route cache hash table entries: 32768 (order: 5, 131072 bytes) >TCP established hash table entries: 131072 (order: 8, 1048576 bytes) >TCP bind hash table entries: 65536 (order: 7, 524288 bytes) >TCP: Hash tables configured (established 131072 bind 65536) >TCP reno registered >TCP bic registered >NET: Registered protocol family 1 >NET: Registered protocol family 15 >Using IPI Shortcut mode >kjournald starting. Commit interval 5 seconds >input: AT Translated Set 2 keyboard on isa0060/serio0 >EXT3-fs: mounted filesystem with ordered data mode. >VFS: Mounted root (ext3 filesystem) readonly. >Freeing unused kernel memory: 188k freed >input: PS/2 Mouse on isa0060/serio4 >input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4 >Adding 977216k swap on /dev/hda1. Priority:-1 extents:1 across:977216k >EXT3 FS on hda2, internal journal >Linux agpgart interface v0.101 (c) Dave Jones >8139too Fast Ethernet driver 0.9.27 >ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 18 >eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:01:82:2d, IRQ 18 >eth0: Identified 8139 chip type 'RTL-8101' >eth0: link up, 10Mbps, half-duplex, lpa 0x0000 >usbcore: registered new driver usbfs >usbcore: registered new driver hub >ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 18 >ehci_hcd 0000:02:07.2: EHCI Host Controller >ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1 >ehci_hcd 0000:02:07.2: irq 18, io mem 0xd0208c00 >ehci_hcd 0000:02:07.2: park 0 >ehci_hcd 0000:02:07.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec >2004 >hub 1-0:1.0: USB hub found >hub 1-0:1.0: 5 ports detected >ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver >(PCI) >ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 18 >ohci_hcd 0000:00:13.0: OHCI Host Controller >ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 >ohci_hcd 0000:00:13.0: irq 18, io mem 0xd0001000 >hub 2-0:1.0: USB hub found >hub 2-0:1.0: 3 ports detected >ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 18 >ohci_hcd 0000:00:13.1: OHCI Host Controller >ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 >ohci_hcd 0000:00:13.1: irq 18, io mem 0xd0002000 >hub 3-0:1.0: USB hub found >hub 3-0:1.0: 3 ports detected >ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 17 >ohci_hcd 0000:02:07.0: OHCI Host Controller >ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4 >ohci_hcd 0000:02:07.0: irq 17, io mem 0xd0206000 >hub 4-0:1.0: USB hub found >hub 4-0:1.0: 3 ports detected >ACPI: PCI Interrupt 0000:02:07.1[B] -> GSI 18 (level, low) -> IRQ 19 >ohci_hcd 0000:02:07.1: OHCI Host Controller >ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5 >ohci_hcd 0000:02:07.1: irq 19, io mem 0xd0207000 >hub 5-0:1.0: USB hub found >hub 5-0:1.0: 2 ports detected >usb 4-1: new low speed USB device using ohci_hcd and address 2 >ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16 >Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b] >Yenta: Enabling burst memory read transactions >Yenta: Using CSCINT to route CSC interrupts to PCI >Yenta: Routing CardBus interrupts to PCI >Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64 >Yenta: ISA IRQ mask 0x0ed8, PCI irq 16 >Socket status: 30000086 >pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff >pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff >pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff >ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 16 (level, low) -> IRQ 17 >Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b] >Yenta: Using CSCINT to route CSC interrupts to PCI >Yenta: Routing CardBus interrupts to PCI >Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64 >input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-1 >usbcore: registered new driver usbhid >drivers/usb/input/hid-core.c: v2.6:USB HID core driver >Yenta: ISA IRQ mask 0x0ed8, PCI irq 17 >Socket status: 30000006 >pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff >pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff >pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff >ieee1394: Initialized config rom entry `ip1394' >ohci1394: $Rev: 1313 $ Ben Collins >ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17 >ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] >MMIO=[d0208000-d02087ff] Max Packet=[2048] >ieee1394: Host added: ID:BUS[0-00:1023] GUID[463f02005c594058] >eth1394: $Rev: 1312 $ Ben Collins >eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) >Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing >disabled >ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5 >ACPI: PCI interrupt for device 0000:00:14.6 disabled >ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5 >agpgart: Detected Ati IGP9100/M chipset >agpgart: AGP aperture is 32M @ 0xd2000000 >USB Universal Host Controller Interface driver v2.3 >ip_tables: (C) 2000-2002 Netfilter core team >ip_conntrack version 2.3 (7168 buckets, 57344 max) - 236 bytes per >conntrack >Installing knfsd (copyright (C) 1996 okir@monad.swb.de). >NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery >directory >NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist >NFSD: starting 90-second grace period >nfsd: last server has exited >nfsd: unexporting all filesystems >NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery >directory >NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist >NFSD: starting 90-second grace period > >Hope this helps. > >David > > >On Sun, 2005-10-30 at 10:33 -0500, Mark Hahn wrote: > > >>>The problem I reported on the linux-kernel list and later here. See >>> >>> >>you mentioned posting the full dmesg(s). in particular, >>are there differences in /proc/interrupts in working and >>non-working kernels? lspci -v might also be interesting. >> >> >> >>>laptop has a P4 Hyperthreaded chip (someone mentioned that there was an >>>ACPI problem related to hyperthreading). >>> >>> >>conceivable, but HT is hardly a new phenomenon. >> >> >> >> > >- >To unsubscribe from this list: send the line "unsubscribe linux-ide" in >the body of a message to majordomo@vger.kernel.org >More majordomo info at http://vger.kernel.org/majordomo-info.html > > > ___________________________________________________________ Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de