Re: sata_sil24 resetting controller...

[Tejun Heo <htejun@gmail.com>]

Jan Dittmer wrote:
> Tejun Heo wrote:
>>> serror=0x0[4297873.266000] sata_sil24 ata1: resetting controller...
>>> [4297873.267000] ata1: status=0x50 { DriveReady SeekComplete }
>>> [4297873.267000] sdc: Current: sense key=0x0
>>> [4297873.267000]     ASC=0x0 ASCQ=0x0
>>>
>>> The time between these events varies from .5s to up to 10s, resync speed is
>>> pretty bad (6mb/s) but appears(!) to be working.
>>> This is with vanilla 2.6.17-rc3, sata drivers built into the kernel.
>>> Find below /proc/interrupts and lspci output. Boot dmesg output was washed
>>> away by above messages, sorry.
>>>
>>> What's the cause of the error, can I ignore it or will it destroy
>>> my raid eventually? I'm now about 5% through the resync process, with 
>>> an estimated finish in 1260 minutes.
>>>
>>> Thanks,
>>>
>>> Jan
>>>
>>>
>>> $ lspci -vv -s 03:04.0
>>> 0000:03:04.0 RAID bus controller: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller (rev 01)
>>> 	Subsystem: Silicon Image, Inc.: Unknown device 7124
>>> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
>>> 	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>>> 	Latency: 32
>>> 	Interrupt: pin A routed to IRQ 22
>>> 	Region 0: Memory at fa800000 (64-bit, non-prefetchable) [size=128]
>>> 	Region 2: Memory at fa000000 (64-bit, non-prefetchable) [size=32K]
>>> 	Region 4: I/O ports at 9400 [size=16]
>>> 	Expansion ROM at fe900000 [disabled] [size=512K]
>>> 	Capabilities: [64] Power Management version 2
>>> 		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>>> 		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
>>> 	Capabilities: [40] PCI-X non-bridge device.
>>> 		Command: DPERE- ERO+ RBC=0 OST=5
>>> 		Status: Bus=3 Dev=4 Func=0 64bit+ 133MHz+ SCD- USC-, DC=simple, DMMRBC=2, DMOST=5, DMCRS=4, RSCEM-
>> So, slow down the PCI-X bus.  It can usually be done from BIOS setup 
>> menu.  Does your machine has a riser board which extends or changes 
>> orientation of PCI-X bus?  Motherboard vendors describe the bus 
>> frequency limit when using riser boards in the manual but sometimes 
>> server vendors forget to set them.  Heck, some of them don't even know 
>> what that is.
> 
> 
> Hmm I don't have a riser card and I don't have a setting for the frequency,
> nor a jumper.
> I plugged the card in another slot, next to a 66MHz only card. So now I've
> it working with 66MHz (checked with lspci), but my drive isn't initialized
> properly anymore:
> 
> [4294690.486000] libata version 1.20 loaded.
> [4294690.486000] sata_sil24 0000:03:04.0: version 0.23
> [4294690.486000] ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 24 (level, low) -> IRQ 22
> [4294690.487000] ata1: SATA max UDMA/100 cmd 0xF8810000 ctl 0x0 bmdma 0x0 irq 22
> [4294690.487000] ata2: SATA max UDMA/100 cmd 0xF8812000 ctl 0x0 bmdma 0x0 irq 22
> [4294690.487000] ata3: SATA max UDMA/100 cmd 0xF8814000 ctl 0x0 bmdma 0x0 irq 22
> [4294690.487000] ata4: SATA max UDMA/100 cmd 0xF8816000 ctl 0x0 bmdma 0x0 irq 22
> [4294690.800000] ata1: SATA link up 3.0 Gbps (SStatus 123)
> [4294690.801000] ata1: dev 0 cfg 49:5145 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0000
> [4294690.801000] ata1: dev 0 ATA-0, max MWDMA2, 16514064 sectors: CHS 16383/16/63
> [4294690.802000] ata1: dev 0 model number mismatch 'WDC WD3200re/sasats_li42S' != ''
> [4294690.802000] ata1: dev 0 revalidation failed (errno=-19)
> [4294690.802000] ata1: failed to revalidate after set xfermode
> [4294690.802000] scsi2 : sata_sil24
> [4294691.003000] ata2: SATA link down (SStatus 0)
> [4294691.003000] scsi3 : sata_sil24
> [4294691.204000] ata3: SATA link down (SStatus 0)
> [4294691.204000] scsi4 : sata_sil24
> [4294691.405000] ata4: SATA link down (SStatus 0)
> [4294691.405000] scsi5 : sata_sil24
> 
> Can this still be a pci bus problem? I get the same error on every reboot.

Hmmm.. max MWDMA2?  Something is very off with your configuration.  Can 
you try the card in another box or on a regular PCI slot?

-- 
tejun