* [sata_sil]Random timeout error (data loss)
@ 2006-04-13 15:17 Martin Ammermüller
2006-04-13 17:59 ` Tejun Heo
0 siblings, 1 reply; 7+ messages in thread
From: Martin Ammermüller @ 2006-04-13 15:17 UTC (permalink / raw)
To: jgarzik; +Cc: linux-ide
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hi!
I get these errors at random with a 2.6.15 (ubuntu) kernel and
2.6.16.{4,5} vanilla kernels and sata_sil with an ATI 4379 SATA
controller and a Toshiba MK8032GS harddrive:
ata1: command 0x25 timeout, stat 0x58 host_stat 0x20
ata1: translated ATA stat/err 0x25/00 to SCSI SK/ASC/ASCQ 0x4/00/00
- -----
ata1: command 0x25 timeout, stat 0xd8 host_stat 0x21
ata1: translated ATA stat/err 0xd8/00 to SCSI SK/ASC/ASCQ 0xb/47/00
- -----
ata1: command 0x35 timeout, stat 0x50 host_stat 0x24
- -----
ACPI-0307: *** Error: No installed handler for fixed event [00000000]
ATA: abnormal status 0x58 on port 0xDC82A087
ATA: abnormal status 0x58 on port 0xDC82A087
ATA: abnormal status 0x58 on port 0xDC82A087
ERROR: (device sda3): diRead: i_ino != di_number
ATA: abnormal status 0x58 on port 0xDC82A087
ATA: abnormal status 0x58 on port 0xDC82A087
ATA: abnormal status 0x58 on port 0xDC82A087
ERROR: (device sda3): diRead: i_ino != di_number
ERROR: (device sda3): diRead: i_ino != di_number
ERROR: (device sda3): diRead: i_ino != di_number
ERROR: (device sda3): diRead: i_ino != di_number
- -----
For further details please see the attached lspci output.
Unfortunately i was not able to reliably reproduce this error. Sometimes
it can occur during a package installation with apt/dpkg but not when i
have a load of 20+ (generated with: "stress --cpu 5 --io 5 --vm 5 --hdd 5").
I also tried with an activated "slow_down" module parameter with no success.
Help is much appreciated, since I am stranded on windows here.
Regards,
Martin Ammermüller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
iD8DBQFEPmuBituPSWPX2AIRAq07AKC9TPM6pj0E6M0LpGqSvf0hC7PE3gCgpoNU
9OU09f9LHY4budxJSskD75k=
=TmdV
-----END PGP SIGNATURE-----
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: [sata_sil]Random timeout error (data loss) 2006-04-13 15:17 [sata_sil]Random timeout error (data loss) Martin Ammermüller @ 2006-04-13 17:59 ` Tejun Heo 2006-04-13 17:56 ` Martin Ammermüller ` (2 more replies) 0 siblings, 3 replies; 7+ messages in thread From: Tejun Heo @ 2006-04-13 17:59 UTC (permalink / raw) To: Martin Ammermüller; +Cc: jgarzik, linux-ide Please post the result of 'lspci -n' -- tejun ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [sata_sil]Random timeout error (data loss) 2006-04-13 17:59 ` Tejun Heo @ 2006-04-13 17:56 ` Martin Ammermüller 2006-05-16 16:07 ` [FYI] Update on sata_sil problem with timeouts (was: Re: [sata_sil]Random timeout error (data loss)) Martin Ammermüller 2006-05-24 16:03 ` [sata_sil]Random timeout error (data loss) Martin Ammermüller 2 siblings, 0 replies; 7+ messages in thread From: Martin Ammermüller @ 2006-04-13 17:56 UTC (permalink / raw) To: Tejun Heo; +Cc: jgarzik, linux-ide -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Tejun Heo schrieb: > Please post the result of 'lspci -n' What i forgot to mention: after the error no data can be written or read to disk anymore (only solution is a hard reset). This applies AFAICS to 2.6.17-rc1 (testet a few minutes ago) with a slightly different error message, too: ata1: command 0xca timeout, stat 0x50 host_stat 0x24 Output of lspci -n : 0000:00:00.0 0600: 1002:5a31 (rev 01) 0000:00:01.0 0604: 1002:5a3f 0000:00:12.0 0101: 1002:4379 (rev 80) 0000:00:13.0 0c03: 1002:4374 (rev 80) 0000:00:13.1 0c03: 1002:4375 (rev 80) 0000:00:13.2 0c03: 1002:4373 (rev 80) 0000:00:14.0 0c05: 1002:4372 (rev 81) 0000:00:14.1 0101: 1002:4376 (rev 80) 0000:00:14.2 0403: 1002:437b (rev 01) 0000:00:14.3 0601: 1002:4377 (rev 80) 0000:00:14.4 0604: 1002:4371 (rev 80) 0000:01:05.0 0300: 1002:5a62 0000:02:04.0 0200: 168c:001a (rev 01) 0000:02:06.0 0607: 1524:1410 (rev 01) 0000:02:07.0 0200: 10ec:8139 (rev 10) 0000:02:0a.0 0c00: 104c:8026 The system is a Toshiba Satellite A100-512 Regards, Martin Ammermüller -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.3 (MingW32) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iD8DBQFEPpDeituPSWPX2AIRAhwmAJoDQi921osUsFS4KRzsvwrkfYyhZACfdoV4 8yW3giN4VUhOiftgdQ+GU84= =g4zF -----END PGP SIGNATURE----- ^ permalink raw reply [flat|nested] 7+ messages in thread
* [FYI] Update on sata_sil problem with timeouts (was: Re: [sata_sil]Random timeout error (data loss)) 2006-04-13 17:59 ` Tejun Heo 2006-04-13 17:56 ` Martin Ammermüller @ 2006-05-16 16:07 ` Martin Ammermüller 2006-05-27 0:22 ` [FYI] Update on sata_sil problem with timeouts Jeff Garzik 2006-05-24 16:03 ` [sata_sil]Random timeout error (data loss) Martin Ammermüller 2 siblings, 1 reply; 7+ messages in thread From: Martin Ammermüller @ 2006-05-16 16:07 UTC (permalink / raw) To: Tejun Heo; +Cc: jgarzik, linux-ide -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I tested 2.6.17-rc4-mm1 and 2.6.17-rc4 in the last days and got similar error messages (command timeout & translated ATA stat/err). I used 5 simultaneously started instances of bonnie++ for testing. Best Regards, Martin Ammermüller -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.3 (MingW32) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iD8DBQFEafjLituPSWPX2AIRAoutAJsGiYeXbjRHLHoKHwU1OrNFi9ACVgCeOOgE FL/vfEQvIDBdRiqlv1nekbc= =Io7D -----END PGP SIGNATURE----- ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [FYI] Update on sata_sil problem with timeouts 2006-05-16 16:07 ` [FYI] Update on sata_sil problem with timeouts (was: Re: [sata_sil]Random timeout error (data loss)) Martin Ammermüller @ 2006-05-27 0:22 ` Jeff Garzik 2006-05-28 12:41 ` Martin Ammermüller 0 siblings, 1 reply; 7+ messages in thread From: Jeff Garzik @ 2006-05-27 0:22 UTC (permalink / raw) To: Martin Ammermüller; +Cc: Tejun Heo, linux-ide Martin Ammermüller wrote: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > I tested 2.6.17-rc4-mm1 and 2.6.17-rc4 in the last days and got similar > error messages (command timeout & translated ATA stat/err). > > I used 5 simultaneously started instances of bonnie++ for testing. Can you retest with the current -mm? Jeff ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [FYI] Update on sata_sil problem with timeouts 2006-05-27 0:22 ` [FYI] Update on sata_sil problem with timeouts Jeff Garzik @ 2006-05-28 12:41 ` Martin Ammermüller 0 siblings, 0 replies; 7+ messages in thread From: Martin Ammermüller @ 2006-05-28 12:41 UTC (permalink / raw) To: Jeff Garzik; +Cc: Tejun Heo, linux-ide [-- Attachment #1: Type: text/plain, Size: 1361 bytes --] -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Jeff Garzik wrote: > Martin Ammermüller wrote: >> -----BEGIN PGP SIGNED MESSAGE----- >> Hash: SHA1 >> >> I tested 2.6.17-rc4-mm1 and 2.6.17-rc4 in the last days and got similar >> error messages (command timeout & translated ATA stat/err). >> >> I used 5 simultaneously started instances of bonnie++ for testing. > > Can you retest with the current -mm? The timeouts still occur, but according to dmesg output they are handled well: - ---- ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen ata1.00: (BMDMA stat 0x21) ata1.00: tag 0 cmd 0xc8 Emask 0x4 stat 0x40 err 0x0 (timeout) ata1: soft resetting port ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: configured for UDMA/100 ata1: EH complete - --- I attached a complete dmesg output from 2.6.17-rc4-mm3 after testing. As i wrote earlier[0], the timeouts do not occur when apic and acpi are turned off. Does that mean that the timeouts are related to acpi/apic not working properly? Best Regards, Martin Ammermüller [0]http://www.spinics.net/lists/linux-ide/msg02485.html -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.2.2 (GNU/Linux) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iD8DBQFEeZp0FjFZ/qjkvZARAtWdAJ40isBKBrfD63OlMqP5RbE2lXFdEgCeLQmK fHIVUwPKG7x08NkCSggr7mY= =cTJo -----END PGP SIGNATURE----- [-- Attachment #2: dmesg.mm3 --] [-- Type: text/plain, Size: 26975 bytes --] [ 0.000000] Linux version 2.6.17-rc4-mm3 (root@tenco) (gcc-Version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Sat May 27 10:30:25 CEST 2006 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] sanitize start [ 0.000000] sanitize end [ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] add_memory_region(0000000000000000, 000000000009f800, 1) [ 0.000000] copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2 [ 0.000000] add_memory_region(000000000009f800, 0000000000000800, 2) [ 0.000000] copy_e820_map() start: 00000000000dc000 size: 0000000000024000 end: 0000000000100000 type: 2 [ 0.000000] add_memory_region(00000000000dc000, 0000000000024000, 2) [ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000001dda0000 end: 000000001dea0000 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] add_memory_region(0000000000100000, 000000001dda0000, 1) [ 0.000000] copy_e820_map() start: 000000001dea0000 size: 0000000000010000 end: 000000001deb0000 type: 3 [ 0.000000] add_memory_region(000000001dea0000, 0000000000010000, 3) [ 0.000000] copy_e820_map() start: 000000001deb0000 size: 0000000000050000 end: 000000001df00000 type: 4 [ 0.000000] add_memory_region(000000001deb0000, 0000000000050000, 4) [ 0.000000] copy_e820_map() start: 000000001df00000 size: 0000000000100000 end: 000000001e000000 type: 2 [ 0.000000] add_memory_region(000000001df00000, 0000000000100000, 2) [ 0.000000] copy_e820_map() start: 00000000e0000000 size: 0000000010000000 end: 00000000f0000000 type: 2 [ 0.000000] add_memory_region(00000000e0000000, 0000000010000000, 2) [ 0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec10000 type: 2 [ 0.000000] add_memory_region(00000000fec00000, 0000000000010000, 2) [ 0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2 [ 0.000000] add_memory_region(00000000fee00000, 0000000000001000, 2) [ 0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2 [ 0.000000] add_memory_region(00000000fff80000, 0000000000080000, 2) [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000001dea0000 (usable) [ 0.000000] BIOS-e820: 000000001dea0000 - 000000001deb0000 (ACPI data) [ 0.000000] BIOS-e820: 000000001deb0000 - 000000001df00000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000001df00000 - 000000001e000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 478MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f7710 [ 0.000000] On node 0 totalpages: 122528 [ 0.000000] DMA zone: 4096 pages, LIFO batch:0 [ 0.000000] Normal zone: 118432 pages, LIFO batch:31 [ 0.000000] DMI present. [ 0.000000] ATI board detected. Disabling timer routing over 8254. [ 0.000000] ACPI: RSDP (v000 TOSINV ) @ 0x000f76c0 [ 0.000000] ACPI: RSDT (v001 TOSINV RSDT 0x06040000 LTP 0x00000000) @ 0x1deabf9b [ 0.000000] ACPI: FADT (v001 TOSINV Goldfish 0x06040000 ATI 0x000f4240) @ 0x1deafef6 [ 0.000000] ACPI: MADT (v001 TOSINV APIC 0x06040000 LTP 0x00000000) @ 0x1deaff6a [ 0.000000] ACPI: MCFG (v001 TOSINV MCFG 0x06040000 LTP 0x00000000) @ 0x1deaffc4 [ 0.000000] ACPI: SSDT (v001 TOSINV Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x1deac1ce [ 0.000000] ACPI: SSDT (v001 TOSINV CpuPm 0x00003000 INTL 0x20030224) @ 0x1deabfd3 [ 0.000000] ACPI: DSDT (v001 TOSINV SB450 0x06040000 MSFT 0x0100000e) @ 0x00000000 [ 0.000000] ACPI: PM-Timer IO Port: 0x8008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 6:13 APIC version 20 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 20000000 (gap: 1e000000:c2000000) [ 0.000000] Detected 1393.494 MHz processor. [ 26.543530] Built 1 zonelists [ 26.543533] Kernel command line: root=/dev/sda3 ro quiet splash [ 26.543759] mapped APIC to ffffe000 (fee00000) [ 26.543762] mapped IOAPIC to ffffd000 (fec00000) [ 26.543765] Enabling fast FPU save and restore... done. [ 26.543768] Enabling unmasked SIMD FPU exception support... done. [ 26.543771] Initializing CPU#0 [ 26.543861] PID hash table entries: 2048 (order: 11, 8192 bytes) [ 26.544952] Console: colour VGA+ 80x25 [ 26.545358] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 26.545793] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 26.561644] Memory: 475972k/490112k available (1949k kernel code, 13512k reserved, 597k data, 312k init, 0k highmem) [ 26.561648] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 26.620760] Calibrating delay using timer specific routine.. 2788.65 BogoMIPS (lpj=1394326) [ 26.620791] Security Framework v1.0.0 initialized [ 26.620802] SELinux: Disabled at boot. [ 26.620812] Mount-cache hash table entries: 512 [ 26.620924] CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000000 00000000 00000000 [ 26.620934] CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000000 00000000 00000000 [ 26.620945] CPU: L1 I cache: 32K, L1 D cache: 32K [ 26.620948] CPU: L2 cache: 1024K [ 26.620950] CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000000 00000000 00000000 [ 26.620967] CPU: Intel(R) Celeron(R) M processor 1.40GHz stepping 08 [ 26.620973] Checking 'hlt' instruction... OK. [ 26.624816] SMP alternatives: switching to UP code [ 26.624819] Freeing SMP alternatives: 0k freed [ 26.643512] ENABLING IO-APIC IRQs [ 26.643703] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 26.653707] ..MP-BIOS bug: 8254 timer not connected to IO-APIC [ 26.653755] ...trying to set up timer (IRQ0) through the 8259A ... failed. [ 26.653758] ...trying to set up timer as Virtual Wire IRQ... works. [ 26.767442] checking if image is initramfs... it is [ 27.469611] Freeing initrd memory: 6000k freed [ 27.470076] NET: Registered protocol family 16 [ 27.470108] EISA bus registered [ 27.470113] ACPI: bus type pci registered [ 27.470120] PCI: Using MMCONFIG [ 27.471105] Setting up standard PCI resources [ 27.474288] ACPI: Subsystem revision 20060310 [ 27.479935] ACPI: Interpreter enabled [ 27.479938] ACPI: Using IOAPIC for interrupt routing [ 27.480760] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 27.480765] PCI: Probing PCI hardware (bus 00) [ 27.482940] PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 [ 27.483233] Boot video device is 0000:01:05.0 [ 27.483749] PCI: Transparent bridge - 0000:00:14.4 [ 27.483849] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 27.487104] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. [ 27.487371] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. [ 27.487653] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. [ 27.487915] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. [ 27.488177] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. [ 27.488439] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. [ 27.488711] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. [ 27.488974] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. [ 27.489559] ACPI: Embedded Controller [EC0] (gpe 7) interrupt mode. [ 27.489782] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] [ 27.490325] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] [ 27.490626] ACPI: Power Resource [PFA1] (off) [ 27.490718] Linux Plug and Play Support v0.97 (c) Adam Belay [ 27.490728] pnp: PnP ACPI init [ 27.503519] pnp: PnP ACPI: found 10 devices [ 27.503525] PnPBIOS: Disabled by ACPI PNP [ 27.503571] PCI: Using ACPI for IRQ routing [ 27.503574] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 27.503881] pnp: 00:08: ioport range 0x1080-0x1080 has been reserved [ 27.503886] pnp: 00:08: ioport range 0x220-0x22f has been reserved [ 27.503889] pnp: 00:08: ioport range 0x400-0x401 has been reserved [ 27.503892] pnp: 00:08: ioport range 0x40b-0x40b has been reserved [ 27.504120] PCI: Bridge: 0000:00:01.0 [ 27.504123] IO window: 9000-9fff [ 27.504127] MEM window: c0100000-c01fffff [ 27.504131] PREFETCH window: d0000000-dfffffff [ 27.504138] PCI: Bus 3, cardbus bridge: 0000:02:06.0 [ 27.504140] IO window: 0000a400-0000a4ff [ 27.504147] IO window: 0000a800-0000a8ff [ 27.504153] PREFETCH window: 20000000-21ffffff [ 27.504160] MEM window: 24000000-25ffffff [ 27.504166] PCI: Bridge: 0000:00:14.4 [ 27.504170] IO window: a000-afff [ 27.504177] MEM window: c0200000-c02fffff [ 27.504182] PREFETCH window: 20000000-21ffffff [ 27.504218] PCI: Enabling device 0000:02:06.0 (0004 -> 0007) [ 27.504226] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 23 (level, low) -> IRQ 177 [ 27.504255] NET: Registered protocol family 2 [ 27.512550] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 27.512649] TCP established hash table entries: 16384 (order: 4, 65536 bytes) [ 27.512722] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 27.512758] TCP: Hash tables configured (established 16384 bind 8192) [ 27.512761] TCP reno registered [ 27.513360] audit: initializing netlink socket (disabled) [ 27.513369] audit(1148734788.136:1): initialized [ 27.513501] VFS: Disk quotas dquot_6.5.1 [ 27.513526] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 27.513573] Initializing Cryptographic API [ 27.513578] io scheduler noop registered [ 27.513586] io scheduler anticipatory registered (default) [ 27.513591] io scheduler deadline registered [ 27.513598] io scheduler cfq registered [ 28.182799] isapnp: Scanning for PnP cards... [ 28.539949] isapnp: No Plug & Play device found [ 28.565938] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 28.567147] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 28.567313] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 28.567317] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 28.567612] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 [ 28.569227] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 28.569490] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 28.569569] mice: PS/2 mouse device common for all mice [ 28.570062] EISA: Probing bus 0 at eisa.0 [ 28.570073] Cannot allocate resource for EISA slot 1 [ 28.570107] Cannot allocate resource for EISA slot 8 [ 28.570109] EISA: Detected 0 cards. [ 28.570215] TCP bic registered [ 28.570226] NET: Registered protocol family 1 [ 28.570235] NET: Registered protocol family 8 [ 28.570237] NET: Registered protocol family 20 [ 28.570265] Using IPI Shortcut mode [ 28.570323] ACPI: (supports S0 S3 S4 S5) [ 28.571018] Time: tsc clocksource has been installed. [ 28.571366] Freeing unused kernel memory: 312k freed [ 28.607104] input: AT Translated Set 2 keyboard as /class/input/input0 [ 28.622668] vga16fb: initializing [ 28.622673] vga16fb: mapped to 0xc00a0000 [ 28.622716] fb0: VGA16 VGA frame buffer device [ 29.732481] ACPI Warning (acpi_power-0427): Transitioning device [FAN1] to D3 [20060310] [ 29.732488] ACPI Warning (acpi_bus-0260): Transitioning device [FAN1] to D3 [20060310] [ 29.732494] ACPI: Fan [FAN1] (off) [ 29.735921] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) [ 29.735927] ACPI: Processor [CPU0] (supports 8 throttling states) [ 29.735933] ACPI Error (acpi_processor-0474): Getting cpuindex for acpiid 0x1 [20060310] [ 2.435000] Time: acpi_pm clocksource has been installed. [ 2.583000] ACPI: Thermal Zone [TZCR] (50 C) [ 2.959000] SCSI subsystem initialized [ 2.963000] libata version 1.30 loaded. [ 2.964000] sata_sil 0000:00:12.0: version 1.0 [ 2.964000] ACPI (acpi_bus-0192): Device `SATA]is not power manageable [20060310] [ 2.964000] PCI: Enabling device 0000:00:12.0 (0005 -> 0007) [ 2.964000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 185 [ 2.964000] ata1: SATA max UDMA/100 cmd 0xDE85E080 ctl 0xDE85E08A bmdma 0xDE85E000 irq 185 [ 2.964000] ata2: SATA max UDMA/100 cmd 0xDE85E0C0 ctl 0xDE85E0CA bmdma 0xDE85E008 irq 185 [ 3.316000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 3.317000] ata1.00: cfg 49:2f00 82:746b 83:7d09 84:6023 85:7469 86:3d09 87:6023 88:203f [ 3.317000] ata1.00: ATA-6, max UDMA/100, 156301488 sectors: LBA48 NCQ (depth 0/32) [ 3.319000] ata1.00: configured for UDMA/100 [ 3.319000] scsi0 : sata_sil [ 3.520000] ata2: SATA link down (SStatus 0 SControl 300) [ 3.520000] scsi1 : sata_sil [ 3.520000] Vendor: ATA Model: TOSHIBA MK8032GS Rev: AS11 [ 3.520000] Type: Direct-Access ANSI SCSI revision: 05 [ 3.528000] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) [ 3.528000] sda: Write Protect is off [ 3.528000] sda: Mode Sense: 00 3a 00 00 [ 3.528000] SCSI device sda: drive cache: write back [ 3.528000] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) [ 3.528000] sda: Write Protect is off [ 3.528000] sda: Mode Sense: 00 3a 00 00 [ 3.528000] SCSI device sda: drive cache: write back [ 3.528000] sda: sda1 sda2 sda3 [ 3.586000] sd 0:0:0:0: Attached scsi disk sda [ 3.896000] ATIIXP: IDE controller at PCI slot 0000:00:14.1 [ 3.896000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 193 [ 3.896000] ATIIXP: chipset revision 128 [ 3.896000] ATIIXP: not 100% native mode: will probe irqs later [ 3.896000] ide0: BM-DMA at 0x8460-0x8467, BIOS settings: hda:pio, hdb:pio [ 3.896000] ide1: BM-DMA at 0x8468-0x846f, BIOS settings: hdc:DMA, hdd:pio [ 3.896000] Probing IDE interface ide0... [ 4.415000] Probing IDE interface ide1... [ 5.088000] hdc: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive [ 5.395000] ide1 at 0x170-0x177,0x376 on irq 15 [ 5.405000] hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) [ 5.405000] Uniform CD-ROM driver Revision: 3.20 [ 5.535000] ieee1394: Initialized config rom entry `ip1394' [ 5.536000] ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 185 [ 5.591000] usbcore: registered new driver usbfs [ 5.591000] usbcore: registered new driver hub [ 5.593000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) [ 5.593000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 201 [ 5.593000] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 5.594000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 [ 5.594000] ohci_hcd 0000:00:13.0: irq 201, io mem 0xc0005000 [ 5.617000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[185] MMIO=[c0215800-c0215fff] Max Packet=[2048] IR/IT contexts=[4/8] [ 5.646000] usb usb1: new device found, idVendor=0000, idProduct=0000 [ 5.646000] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.646000] usb usb1: Product: OHCI Host Controller [ 5.646000] usb usb1: Manufacturer: Linux 2.6.17-rc4-mm3 ohci_hcd [ 5.646000] usb usb1: SerialNumber: 0000:00:13.0 [ 5.646000] usb usb1: configuration #1 chosen from 1 choice [ 5.646000] hub 1-0:1.0: USB hub found [ 5.646000] hub 1-0:1.0: 4 ports detected [ 5.747000] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 201 [ 5.747000] ohci_hcd 0000:00:13.1: OHCI Host Controller [ 5.747000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 [ 5.747000] ohci_hcd 0000:00:13.1: irq 201, io mem 0xc0006000 [ 5.802000] usb usb2: new device found, idVendor=0000, idProduct=0000 [ 5.802000] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.802000] usb usb2: Product: OHCI Host Controller [ 5.802000] usb usb2: Manufacturer: Linux 2.6.17-rc4-mm3 ohci_hcd [ 5.802000] usb usb2: SerialNumber: 0000:00:13.1 [ 5.802000] usb usb2: configuration #1 chosen from 1 choice [ 5.802000] hub 2-0:1.0: USB hub found [ 5.802000] hub 2-0:1.0: 4 ports detected [ 5.917000] ACPI (acpi_bus-0192): Device `EHCI]is not power manageable [20060310] [ 5.917000] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 201 [ 5.917000] ehci_hcd 0000:00:13.2: EHCI Host Controller [ 5.917000] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 5.917000] ehci_hcd 0000:00:13.2: irq 201, io mem 0xc0007000 [ 5.917000] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 5.917000] usb usb3: new device found, idVendor=0000, idProduct=0000 [ 5.917000] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.917000] usb usb3: Product: EHCI Host Controller [ 5.917000] usb usb3: Manufacturer: Linux 2.6.17-rc4-mm3 ehci_hcd [ 5.917000] usb usb3: SerialNumber: 0000:00:13.2 [ 5.917000] usb usb3: configuration #1 chosen from 1 choice [ 5.917000] hub 3-0:1.0: USB hub found [ 5.917000] hub 3-0:1.0: 8 ports detected [ 5.964000] usb 1-1: new low speed USB device using ohci_hcd and address 2 [ 6.045000] Probing IDE interface ide0... [ 6.496000] usb 1-1: new low speed USB device using ohci_hcd and address 3 [ 6.590000] Attempting manual resume [ 6.598000] JFS: nTxBlock = 3769, nTxLock = 30158 [ 6.643000] usb 1-1: new device found, idVendor=045e, idProduct=007d [ 6.643000] usb 1-1: new device strings: Mfr=1, Product=3, SerialNumber=0 [ 6.643000] usb 1-1: Product: Microsoft 3-Button Mouse with IntelliEye? [ 6.643000] usb 1-1: Manufacturer: Microsoft [ 6.643000] usb 1-1: configuration #1 chosen from 1 choice [ 6.659000] usbcore: registered new driver hiddev [ 6.662000] input: Microsoft Microsoft 3-Button Mouse with IntelliEye? as /class/input/input1 [ 6.662000] input: USB HID v1.00 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye?] on usb-0000:00:13.0-1 [ 6.662000] usbcore: registered new driver usbhid [ 6.662000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 6.873000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00080da0233934d1] [ 14.754000] ts: Compaq touchscreen protocol output [ 14.997000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 16.448000] Linux agpgart interface v0.101 (c) Dave Jones [ 16.514000] input: PC Speaker as /class/input/input2 [ 16.570000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 16.574000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 16.734000] Real Time Clock Driver v1.12ac [ 17.124000] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device [ 17.168000] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 23 (level, low) -> IRQ 177 [ 17.168000] Yenta: CardBus bridge found at 0000:02:06.0 [1179:ff10] [ 17.168000] Yenta: Enabling burst memory read transactions [ 17.168000] Yenta: Using CSCINT to route CSC interrupts to PCI [ 17.168000] Yenta: Routing CardBus interrupts to PCI [ 17.168000] Yenta TI: socket 0000:02:06.0, mfunc 0x01111122, devctl 0x44 [ 17.235000] 8139too Fast Ethernet driver 0.9.27 [ 17.391000] Yenta: ISA IRQ mask 0x0ef8, PCI irq 177 [ 17.391000] Socket status: 30000006 [ 17.391000] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff [ 17.391000] cs: IO port probe 0xa000-0xafff: clean. [ 17.392000] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff [ 17.392000] pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x21ffffff [ 17.543000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x0 [ 17.543000] synaptics: Toshiba Satellite A100 detected, limiting rate to 40pps. [ 17.578000] input: SynPS/2 Synaptics TouchPad as /class/input/input3 [ 17.669000] ACPI (acpi_bus-0192): Device `LANC]is not power manageable [20060310] [ 17.669000] ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 20 (level, low) -> IRQ 209 [ 17.669000] eth0: RealTek RTL8139 at 0xdec94000, 00:a0:d1:34:39:23, IRQ 209 [ 17.669000] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [ 17.676000] ACPI (acpi_bus-0192): Device `MODM]is not power manageable [20060310] [ 17.676000] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 193 [ 17.683000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) [ 17.847000] ACPI Error (evxfevnt-0386): Could not disable RealTimeClock events [20060310] [ 17.857000] hda_codec: Unknown model for ALC861, trying auto-probe from BIOS... [ 18.376000] cs: IO port probe 0x100-0x3af: excluding 0x1f0-0x1f7 [ 18.378000] cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7 [ 18.379000] cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f [ 18.380000] cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf [ 18.381000] cs: IO port probe 0xa00-0xaff: clean. [ 19.078000] lp: driver loaded but no devices found [ 19.198000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) [ 19.198000] ieee1394: sbp2: Try serialize_io=0 for better performance [ 19.398000] Adding 971924k swap on /dev/sda2. Priority:-1 extents:1 across:971924k [ 22.171000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 [ 22.171000] md: bitmap version 4.39 [ 25.471000] device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com [ 29.075000] device-mapper: dm-linear: Device lookup failed [ 29.075000] device-mapper: error adding target to table [ 29.075000] device-mapper: dm-linear: Device lookup failed [ 29.075000] device-mapper: error adding target to table [ 29.076000] device-mapper: dm-linear: Device lookup failed [ 29.076000] device-mapper: error adding target to table [ 29.076000] device-mapper: dm-linear: Device lookup failed [ 29.076000] device-mapper: error adding target to table [ 29.076000] device-mapper: dm-linear: Device lookup failed [ 29.076000] device-mapper: error adding target to table [ 29.077000] device-mapper: dm-linear: Device lookup failed [ 29.077000] device-mapper: error adding target to table [ 29.077000] device-mapper: dm-linear: Device lookup failed [ 29.077000] device-mapper: error adding target to table [ 29.077000] device-mapper: dm-linear: Device lookup failed [ 29.077000] device-mapper: error adding target to table [ 29.078000] device-mapper: dm-linear: Device lookup failed [ 29.078000] device-mapper: error adding target to table [ 29.078000] device-mapper: dm-linear: Device lookup failed [ 29.078000] device-mapper: error adding target to table [ 29.079000] device-mapper: dm-linear: Device lookup failed [ 29.079000] device-mapper: error adding target to table [ 29.079000] device-mapper: dm-linear: Device lookup failed [ 29.079000] device-mapper: error adding target to table [ 29.441000] NTFS driver 2.1.27 [Flags: R/O MODULE]. [ 29.593000] NTFS volume version 3.1. [ 31.616000] ACPI: AC Adapter [ADP0] (on-line) [ 31.745000] ACPI: Battery Slot [BAT0] (battery present) [ 31.765000] ACPI Exception (utmutex-0257): AE_TIME, Thread 0 could not acquire Mutex [8] [20060310] [ 31.765000] ACPI Exception (utmutex-0257): AE_TIME, Thread 0 could not acquire Mutex [8] [20060310] [ 31.766000] ACPI: Power Button (FF) [PWRF] [ 31.766000] ACPI: Power Button (CM) [PWRB] [ 31.766000] ACPI: Lid Switch [LID] [ 31.820000] Using specific hotkey driver [ 31.844000] ibm_acpi: ec object not found [ 31.845000] ACPI Error (evxfevnt-0386): Could not disable RealTimeClock events [20060310] [ 31.902000] toshiba_acpi: Unknown parameter `hotkeys_over_acpi' [ 37.044000] [drm] Initialized drm 1.0.1 20051102 [ 37.180000] ppdev: user-space parallel port driver [ 37.612000] apm: BIOS not found. [ 41.123000] Bluetooth: Core ver 2.8 [ 41.123000] NET: Registered protocol family 31 [ 41.123000] Bluetooth: HCI device and connection manager initialized [ 41.123000] Bluetooth: HCI socket layer initialized [ 41.187000] Bluetooth: L2CAP ver 2.8 [ 41.187000] Bluetooth: L2CAP socket layer initialized [ 41.203000] Bluetooth: RFCOMM socket layer initialized [ 41.203000] Bluetooth: RFCOMM TTY layer initialized [ 41.203000] Bluetooth: RFCOMM ver 1.7 [ 45.459000] hda-intel: Invalid position buffer, using LPIB read method instead. [ 321.333000] ACPI Error (evevent-0314): No installed handler for fixed event [00000000] [20060310] [ 3001.392000] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen [ 3001.392000] ata1.00: (BMDMA stat 0x21) [ 3001.392000] ata1.00: tag 0 cmd 0xc8 Emask 0x4 stat 0x40 err 0x0 (timeout) [ 3001.392000] ata1: soft resetting port [ 3001.543000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 3001.546000] ata1.00: configured for UDMA/100 [ 3001.546000] ata1: EH complete [ 3034.178000] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen [ 3034.178000] ata1.00: (BMDMA stat 0x21) [ 3034.178000] ata1.00: tag 0 cmd 0xc8 Emask 0x4 stat 0x40 err 0x0 (timeout) [ 3034.178000] ata1: soft resetting port [ 3034.329000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 3034.333000] ata1.00: configured for UDMA/100 [ 3034.333000] ata1: EH complete [ 4288.145000] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen [ 4288.145000] ata1.00: (BMDMA stat 0x21) [ 4288.145000] ata1.00: tag 0 cmd 0xc8 Emask 0x4 stat 0x40 err 0x0 (timeout) [ 4288.145000] ata1: soft resetting port [ 4288.296000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 4288.299000] ata1.00: configured for UDMA/100 [ 4288.300000] ata1: EH complete ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [sata_sil]Random timeout error (data loss) 2006-04-13 17:59 ` Tejun Heo 2006-04-13 17:56 ` Martin Ammermüller 2006-05-16 16:07 ` [FYI] Update on sata_sil problem with timeouts (was: Re: [sata_sil]Random timeout error (data loss)) Martin Ammermüller @ 2006-05-24 16:03 ` Martin Ammermüller 2 siblings, 0 replies; 7+ messages in thread From: Martin Ammermüller @ 2006-05-24 16:03 UTC (permalink / raw) To: Tejun Heo; +Cc: jgarzik, linux-ide [-- Attachment #1: Type: text/plain, Size: 871 bytes --] -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Thanks to Fourat Zouari, who got the same notebook as i, i was able to solve the timeout problem by appending "noapic acpi=off" to my kernel boot command. Additionaly, i tested 2.6.17-rc4-git2 with the great update patch and apic and acpi turned on. It seems that sata_sil error handling works. At least dmesg contained messages about libata error handling ("EH" lines). Since a notebook without acpi isn't quite usable, i would be happy if someone could point me to a site where i can get further help to investigate the acpi issue. Best Regards, Martin Ammermüller -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.2.2 (GNU/Linux) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iD8DBQFEdIPrFjFZ/qjkvZARAmWqAJ9HpAX3KYXYXtY93Rv+ixoKQwgopACff6sR BWnADQihiO8n4E5css+ymE0= =ArDN -----END PGP SIGNATURE----- [-- Attachment #2: dmesg_libata --] [-- Type: text/plain, Size: 22568 bytes --] [4294667.296000] Linux version 2.6.17-rc4-git2 (root@tenco) (gcc-Version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Thu May 18 16:00:48 CEST 2006 [4294667.296000] BIOS-provided physical RAM map: [4294667.296000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [4294667.296000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [4294667.296000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) [4294667.296000] BIOS-e820: 0000000000100000 - 000000001dea0000 (usable) [4294667.296000] BIOS-e820: 000000001dea0000 - 000000001deb0000 (ACPI data) [4294667.296000] BIOS-e820: 000000001deb0000 - 000000001df00000 (ACPI NVS) [4294667.296000] BIOS-e820: 000000001df00000 - 000000001e000000 (reserved) [4294667.296000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [4294667.296000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [4294667.296000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [4294667.296000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [4294667.296000] 0MB HIGHMEM available. [4294667.296000] 478MB LOWMEM available. [4294667.296000] found SMP MP-table at 000f7710 [4294667.296000] On node 0 totalpages: 122528 [4294667.296000] DMA zone: 4096 pages, LIFO batch:0 [4294667.296000] Normal zone: 118432 pages, LIFO batch:31 [4294667.296000] DMI present. [4294667.296000] ATI board detected. Disabling timer routing over 8254. [4294667.296000] ACPI: RSDP (v000 TOSINV ) @ 0x000f76c0 [4294667.296000] ACPI: RSDT (v001 TOSINV RSDT 0x06040000 LTP 0x00000000) @ 0x1deabf9b [4294667.296000] ACPI: FADT (v001 TOSINV Goldfish 0x06040000 ATI 0x000f4240) @ 0x1deafef6 [4294667.296000] ACPI: MADT (v001 TOSINV APIC 0x06040000 LTP 0x00000000) @ 0x1deaff6a [4294667.296000] ACPI: MCFG (v001 TOSINV MCFG 0x06040000 LTP 0x00000000) @ 0x1deaffc4 [4294667.296000] ACPI: SSDT (v001 TOSINV Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x1deac1ce [4294667.296000] ACPI: SSDT (v001 TOSINV CpuPm 0x00003000 INTL 0x20030224) @ 0x1deabfd3 [4294667.296000] ACPI: DSDT (v001 TOSINV SB450 0x06040000 MSFT 0x0100000e) @ 0x00000000 [4294667.296000] ACPI: PM-Timer IO Port: 0x8008 [4294667.296000] ACPI: Local APIC address 0xfee00000 [4294667.296000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [4294667.296000] Processor #0 6:13 APIC version 20 [4294667.296000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [4294667.296000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [4294667.296000] IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23 [4294667.296000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) [4294667.296000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) [4294667.296000] ACPI: IRQ0 used by override. [4294667.296000] ACPI: IRQ2 used by override. [4294667.296000] Enabling APIC mode: Flat. Using 1 I/O APICs [4294667.296000] Using ACPI (MADT) for SMP configuration information [4294667.296000] Allocating PCI resources starting at 20000000 (gap: 1e000000:c2000000) [4294667.296000] Built 1 zonelists [4294667.296000] Kernel command line: root=/dev/sda3 ro quiet splash [4294667.296000] mapped APIC to ffffd000 (fee00000) [4294667.296000] mapped IOAPIC to ffffc000 (fec00000) [4294667.296000] Enabling fast FPU save and restore... done. [4294667.296000] Enabling unmasked SIMD FPU exception support... done. [4294667.296000] Initializing CPU#0 [4294667.296000] PID hash table entries: 2048 (order: 11, 8192 bytes) [4294667.296000] Detected 1394.231 MHz processor. [4294667.296000] Using pmtmr for high-res timesource [4294667.296000] Console: colour VGA+ 80x25 [4294671.231000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [4294671.232000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [4294671.247000] Memory: 476196k/490112k available (1893k kernel code, 13272k reserved, 586k data, 288k init, 0k highmem) [4294671.247000] Checking if this processor honours the WP bit even in supervisor mode... Ok. [4294671.307000] Calibrating delay using timer specific routine.. 2790.10 BogoMIPS (lpj=1395053) [4294671.307000] Security Framework v1.0.0 initialized [4294671.307000] SELinux: Disabled at boot. [4294671.307000] Mount-cache hash table entries: 512 [4294671.307000] CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000000 00000000 00000000 [4294671.307000] CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000000 00000000 00000000 [4294671.307000] CPU: L1 I cache: 32K, L1 D cache: 32K [4294671.307000] CPU: L2 cache: 1024K [4294671.307000] CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000000 00000000 00000000 [4294671.307000] CPU: Intel(R) Celeron(R) M processor 1.40GHz stepping 08 [4294671.307000] Checking 'hlt' instruction... OK. [4294671.311000] SMP alternatives: switching to UP code [4294671.311000] Freeing SMP alternatives: 0k freed [4294671.329000] ENABLING IO-APIC IRQs [4294671.329000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [4294671.329000] ..MP-BIOS bug: 8254 timer not connected to IO-APIC [4294671.329000] ...trying to set up timer (IRQ0) through the 8259A ... failed. [4294671.329000] ...trying to set up timer as Virtual Wire IRQ... works. [4294671.450000] checking if image is initramfs... it is [4294672.143000] Freeing initrd memory: 5869k freed [4294672.144000] NET: Registered protocol family 16 [4294672.144000] EISA bus registered [4294672.144000] ACPI: bus type pci registered [4294672.144000] PCI: Using MMCONFIG [4294672.145000] Setting up standard PCI resources [4294672.148000] ACPI: Subsystem revision 20060127 [4294672.157000] ACPI: Interpreter enabled [4294672.157000] ACPI: Using IOAPIC for interrupt routing [4294672.158000] ACPI: PCI Root Bridge [PCI0] (0000:00) [4294672.158000] PCI: Probing PCI hardware (bus 00) [4294672.160000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 [4294672.160000] Boot video device is 0000:01:05.0 [4294672.161000] PCI: Transparent bridge - 0000:00:14.4 [4294672.161000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [4294672.164000] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. [4294672.164000] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. [4294672.165000] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. [4294672.165000] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. [4294672.165000] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. [4294672.165000] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. [4294672.166000] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. [4294672.166000] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. [4294672.167000] ACPI: Embedded Controller [EC0] (gpe 7) interrupt mode. [4294672.167000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] [4294672.167000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] [4294672.168000] ACPI: Power Resource [PFA1] (off) [4294672.168000] Linux Plug and Play Support v0.97 (c) Adam Belay [4294672.168000] pnp: PnP ACPI init [4294672.181000] pnp: PnP ACPI: found 10 devices [4294672.181000] PnPBIOS: Disabled by ACPI PNP [4294672.181000] PCI: Using ACPI for IRQ routing [4294672.181000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [4294672.181000] pnp: 00:08: ioport range 0x1080-0x1080 has been reserved [4294672.181000] pnp: 00:08: ioport range 0x220-0x22f has been reserved [4294672.181000] pnp: 00:08: ioport range 0x400-0x401 has been reserved [4294672.181000] pnp: 00:08: ioport range 0x40b-0x40b has been reserved [4294672.181000] PCI: Bridge: 0000:00:01.0 [4294672.181000] IO window: 9000-9fff [4294672.181000] MEM window: c0100000-c01fffff [4294672.181000] PREFETCH window: d0000000-dfffffff [4294672.181000] PCI: Bus 3, cardbus bridge: 0000:02:06.0 [4294672.181000] IO window: 0000a400-0000a4ff [4294672.181000] IO window: 0000a800-0000a8ff [4294672.181000] PREFETCH window: 20000000-21ffffff [4294672.181000] MEM window: 24000000-25ffffff [4294672.181000] PCI: Bridge: 0000:00:14.4 [4294672.181000] IO window: a000-afff [4294672.181000] MEM window: c0200000-c02fffff [4294672.181000] PREFETCH window: 20000000-21ffffff [4294672.181000] PCI: Enabling device 0000:02:06.0 (0004 -> 0007) [4294672.181000] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 23 (level, low) -> IRQ 177 [4294672.181000] NET: Registered protocol family 2 [4294672.190000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [4294672.190000] TCP established hash table entries: 16384 (order: 4, 65536 bytes) [4294672.190000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [4294672.190000] TCP: Hash tables configured (established 16384 bind 8192) [4294672.190000] TCP reno registered [4294672.190000] audit: initializing netlink socket (disabled) [4294672.190000] audit(1147970692.189:1): initialized [4294672.190000] VFS: Disk quotas dquot_6.5.1 [4294672.190000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [4294672.190000] Initializing Cryptographic API [4294672.190000] io scheduler noop registered [4294672.190000] io scheduler anticipatory registered (default) [4294672.191000] io scheduler deadline registered [4294672.191000] io scheduler cfq registered [4294672.860000] isapnp: Scanning for PnP cards... [4294673.218000] isapnp: No Plug & Play device found [4294673.240000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [4294673.242000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [4294673.242000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [4294673.242000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [4294673.242000] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 [4294673.244000] serio: i8042 AUX port at 0x60,0x64 irq 12 [4294673.244000] serio: i8042 KBD port at 0x60,0x64 irq 1 [4294673.244000] mice: PS/2 mouse device common for all mice [4294673.245000] EISA: Probing bus 0 at eisa.0 [4294673.245000] Cannot allocate resource for EISA slot 1 [4294673.245000] Cannot allocate resource for EISA slot 8 [4294673.245000] EISA: Detected 0 cards. [4294673.245000] TCP bic registered [4294673.245000] NET: Registered protocol family 1 [4294673.245000] NET: Registered protocol family 8 [4294673.245000] NET: Registered protocol family 20 [4294673.245000] Using IPI Shortcut mode [4294673.245000] ACPI wakeup devices: [4294673.245000] LID OHC1 OHC2 EHCI P2P LANC AUDO MODM [4294673.245000] ACPI: (supports S0 S3 S4 S5) [4294673.246000] Freeing unused kernel memory: 288k freed [4294673.282000] input: AT Translated Set 2 keyboard as /class/input/input0 [4294673.305000] ACPI: Fan [FAN1] (off) [4294673.309000] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) [4294673.309000] ACPI: Processor [CPU0] (supports 8 throttling states) [4294673.470000] ACPI: Thermal Zone [TZCR] (51 C) [4294673.777000] SCSI subsystem initialized [4294673.781000] libata version 1.30 loaded. [4294673.782000] sata_sil 0000:00:12.0: version 1.0 [4294673.782000] PCI: Enabling device 0000:00:12.0 (0005 -> 0007) [4294673.782000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 185 [4294673.782000] ata1: SATA max UDMA/100 cmd 0xDE82A080 ctl 0xDE82A08A bmdma 0xDE82A000 irq 185 [4294673.782000] ata2: SATA max UDMA/100 cmd 0xDE82A0C0 ctl 0xDE82A0CA bmdma 0xDE82A008 irq 185 [4294674.134000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [4294674.136000] ata1.00: cfg 49:2f00 82:746b 83:7d09 84:6023 85:7469 86:3d09 87:6023 88:203f [4294674.136000] ata1.00: ATA-6, max UDMA/100, 156301488 sectors: LBA48 NCQ (depth 0/32) [4294674.138000] ata1.00: configured for UDMA/100 [4294674.138000] scsi0 : sata_sil [4294674.340000] ata2: SATA link down (SStatus 0 SControl 300) [4294674.340000] scsi1 : sata_sil [4294674.341000] Vendor: ATA Model: TOSHIBA MK8032GS Rev: AS11 [4294674.341000] Type: Direct-Access ANSI SCSI revision: 05 [4294674.348000] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) [4294674.348000] sda: Write Protect is off [4294674.348000] sda: Mode Sense: 00 3a 00 00 [4294674.348000] SCSI device sda: drive cache: write back [4294674.348000] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) [4294674.348000] sda: Write Protect is off [4294674.348000] sda: Mode Sense: 00 3a 00 00 [4294674.348000] SCSI device sda: drive cache: write back [4294674.348000] sda: sda1 sda2 sda3 [4294674.399000] sd 0:0:0:0: Attached scsi disk sda [4294674.721000] ATIIXP: IDE controller at PCI slot 0000:00:14.1 [4294674.721000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 193 [4294674.721000] ATIIXP: chipset revision 128 [4294674.721000] ATIIXP: not 100% native mode: will probe irqs later [4294674.721000] ide0: BM-DMA at 0x8460-0x8467, BIOS settings: hda:pio, hdb:pio [4294674.721000] ide1: BM-DMA at 0x8468-0x846f, BIOS settings: hdc:DMA, hdd:pio [4294674.721000] Probing IDE interface ide0... [4294675.240000] Probing IDE interface ide1... [4294675.912000] hdc: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive [4294676.219000] ide1 at 0x170-0x177,0x376 on irq 15 [4294676.228000] hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) [4294676.228000] Uniform CD-ROM driver Revision: 3.20 [4294676.366000] usbcore: registered new driver usbfs [4294676.366000] usbcore: registered new driver hub [4294676.366000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) [4294676.366000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 201 [4294676.366000] ohci_hcd 0000:00:13.0: OHCI Host Controller [4294676.367000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 [4294676.367000] ohci_hcd 0000:00:13.0: irq 201, io mem 0xc0005000 [4294676.418000] usb usb1: configuration #1 chosen from 1 choice [4294676.418000] hub 1-0:1.0: USB hub found [4294676.418000] hub 1-0:1.0: 4 ports detected [4294676.519000] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 201 [4294676.519000] ohci_hcd 0000:00:13.1: OHCI Host Controller [4294676.519000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 [4294676.519000] ohci_hcd 0000:00:13.1: irq 201, io mem 0xc0006000 [4294676.570000] usb usb2: configuration #1 chosen from 1 choice [4294676.570000] hub 2-0:1.0: USB hub found [4294676.570000] hub 2-0:1.0: 4 ports detected [4294676.671000] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 201 [4294676.671000] ehci_hcd 0000:00:13.2: EHCI Host Controller [4294676.671000] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 [4294676.672000] ehci_hcd 0000:00:13.2: irq 201, io mem 0xc0007000 [4294676.672000] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [4294676.672000] usb usb3: configuration #1 chosen from 1 choice [4294676.672000] hub 3-0:1.0: USB hub found [4294676.672000] hub 3-0:1.0: 8 ports detected [4294676.792000] Probing IDE interface ide0... [4294677.245000] usb 1-1: new low speed USB device using ohci_hcd and address 3 [4294677.337000] Attempting manual resume [4294677.343000] JFS: nTxBlock = 3770, nTxLock = 30163 [4294677.390000] usb 1-1: configuration #1 chosen from 1 choice [4294677.406000] usbcore: registered new driver hiddev [4294677.412000] input: Microsoft Microsoft 3-Button Mouse with IntelliEye? as /class/input/input1 [4294677.412000] input: USB HID v1.00 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye?] on usb-0000:00:13.0-1 [4294677.412000] usbcore: registered new driver usbhid [4294677.412000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [4294681.666000] ts: Compaq touchscreen protocol output [4294681.756000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [4294682.500000] input: PC Speaker as /class/input/input2 [4294682.673000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [4294682.724000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [4294682.749000] Linux agpgart interface v0.101 (c) Dave Jones [4294682.937000] Real Time Clock Driver v1.12ac [4294683.154000] ieee1394: Initialized config rom entry `ip1394' [4294683.252000] ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 185 [4294683.303000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[185] MMIO=[c0215800-c0215fff] Max Packet=[2048] IR/IT contexts=[4/8] [4294683.336000] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 23 (level, low) -> IRQ 177 [4294683.336000] Yenta: CardBus bridge found at 0000:02:06.0 [1179:ff10] [4294683.336000] Yenta: Enabling burst memory read transactions [4294683.336000] Yenta: Using CSCINT to route CSC interrupts to PCI [4294683.336000] Yenta: Routing CardBus interrupts to PCI [4294683.336000] Yenta TI: socket 0000:02:06.0, mfunc 0x01111122, devctl 0x44 [4294683.343000] 8139too Fast Ethernet driver 0.9.27 [4294683.559000] Yenta: ISA IRQ mask 0x0ef8, PCI irq 177 [4294683.559000] Socket status: 30000006 [4294683.559000] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff [4294683.559000] cs: IO port probe 0xa000-0xafff: clean. [4294683.560000] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff [4294683.560000] pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x21ffffff [4294683.802000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x0 [4294683.802000] synaptics: Toshiba Satellite A100 detected, limiting rate to 40pps. [4294683.824000] ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 20 (level, low) -> IRQ 209 [4294683.824000] eth0: RealTek RTL8139 at 0xdebcc000, 00:a0:d1:34:39:23, IRQ 209 [4294683.824000] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [4294683.837000] input: SynPS/2 Synaptics TouchPad as /class/input/input3 [4294683.863000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) [4294683.967000] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 193 [4294684.100000] ACPI Error (evxfevnt-0388): Could not disable RealTimeClock events [20060127] [4294684.144000] hda_codec: Unknown model for ALC861, trying auto-probe from BIOS... [4294684.559000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00080da0d1343923] [4294684.592000] cs: IO port probe 0x100-0x3af: excluding 0x1f0-0x1f7 [4294684.595000] cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7 [4294684.596000] cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f [4294684.597000] cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf [4294684.598000] cs: IO port probe 0xa00-0xaff: clean. [4294684.988000] lp: driver loaded but no devices found [4294685.026000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) [4294685.026000] ieee1394: sbp2: Try serialize_io=0 for better performance [4294685.136000] Adding 971924k swap on /dev/sda2. Priority:-1 extents:1 across:971924k [4294686.000000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 [4294686.000000] md: bitmap version 4.39 [4294686.802000] device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com [4294688.303000] device-mapper: dm-linear: Device lookup failed [4294688.303000] device-mapper: error adding target to table [4294688.304000] device-mapper: dm-linear: Device lookup failed [4294688.304000] device-mapper: error adding target to table [4294688.305000] device-mapper: dm-linear: Device lookup failed [4294688.305000] device-mapper: error adding target to table [4294688.306000] device-mapper: dm-linear: Device lookup failed [4294688.306000] device-mapper: error adding target to table [4294688.307000] device-mapper: dm-linear: Device lookup failed [4294688.308000] device-mapper: error adding target to table [4294688.309000] device-mapper: dm-linear: Device lookup failed [4294688.309000] device-mapper: error adding target to table [4294688.310000] device-mapper: dm-linear: Device lookup failed [4294688.310000] device-mapper: error adding target to table [4294688.311000] device-mapper: dm-linear: Device lookup failed [4294688.311000] device-mapper: error adding target to table [4294688.312000] device-mapper: dm-linear: Device lookup failed [4294688.312000] device-mapper: error adding target to table [4294688.313000] device-mapper: dm-linear: Device lookup failed [4294688.313000] device-mapper: error adding target to table [4294688.315000] device-mapper: dm-linear: Device lookup failed [4294688.315000] device-mapper: error adding target to table [4294688.316000] device-mapper: dm-linear: Device lookup failed [4294688.316000] device-mapper: error adding target to table [4294688.461000] NTFS driver 2.1.27 [Flags: R/O MODULE]. [4294688.577000] NTFS volume version 3.1. [4294691.140000] ACPI: AC Adapter [ADP0] (on-line) [4294691.271000] ACPI: Battery Slot [BAT0] (battery present) [4294691.290000] ACPI Exception (utmutex-0257): AE_TIME, Thread 0 could not acquire Mutex [8] [20060127] [4294691.290000] ACPI Exception (utmutex-0257): AE_TIME, Thread 0 could not acquire Mutex [8] [20060127] [4294691.291000] ACPI: Power Button (FF) [PWRF] [4294691.292000] ACPI: Power Button (CM) [PWRB] [4294691.292000] ACPI: Lid Switch [LID] [4294691.344000] Using specific hotkey driver [4294691.367000] ibm_acpi: ec object not found [4294925.115000] ACPI Error (evevent-0312): No installed handler for fixed event [00000000] [20060127] [4296109.762000] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x3 frozen [4296109.762000] ata1.00: (BMDMA stat 0x21) [4296109.762000] ata1.00: tag 0 cmd 0xc8 Emask 0x4 stat 0x40 err 0x0 (timeout) [4296109.763000] ata1: soft resetting port [4296109.914000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [4296109.919000] ata1.00: configured for UDMA/100 [4296109.919000] ata1: EH complete [4296451.308000] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x3 frozen [4296451.308000] ata1.00: (BMDMA stat 0x21) [4296451.308000] ata1.00: tag 0 cmd 0xc8 Emask 0x4 stat 0x40 err 0x0 (timeout) [4296451.308000] ata1: soft resetting port [4296451.459000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [4296451.463000] ata1.00: configured for UDMA/100 [4296451.463000] ata1: EH complete [4296764.739000] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x3 frozen [4296764.739000] ata1.00: (BMDMA stat 0x21) [4296764.739000] ata1.00: tag 0 cmd 0xc8 Emask 0x4 stat 0x40 err 0x0 (timeout) [4296764.739000] ata1: soft resetting port [4296764.890000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [4296764.894000] ata1.00: configured for UDMA/100 [4296764.894000] ata1: EH complete ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2006-05-28 12:41 UTC | newest] Thread overview: 7+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2006-04-13 15:17 [sata_sil]Random timeout error (data loss) Martin Ammermüller 2006-04-13 17:59 ` Tejun Heo 2006-04-13 17:56 ` Martin Ammermüller 2006-05-16 16:07 ` [FYI] Update on sata_sil problem with timeouts (was: Re: [sata_sil]Random timeout error (data loss)) Martin Ammermüller 2006-05-27 0:22 ` [FYI] Update on sata_sil problem with timeouts Jeff Garzik 2006-05-28 12:41 ` Martin Ammermüller 2006-05-24 16:03 ` [sata_sil]Random timeout error (data loss) Martin Ammermüller
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).