From: "Berck E. Nash" <flyboy@gmail.com>
To: "linux-ide@vger.kernel.org" <linux-ide@vger.kernel.org>
Subject: libata Intel PIIX/ICH fails to detect both PATA drives, spews ACPI errors
Date: Fri, 01 Dec 2006 09:19:36 -0700 [thread overview]
Message-ID: <45705618.2020608@gmail.com> (raw)
Testing the new libata ICH PATA drivers. There's one PATA port on this
chip, and I've got two optical drives connected to it. The master drive
fails to detect. The slave detects and works properly.
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE
Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
[ 128.400965] ata5: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0
irq 14
[ 128.407976] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xFFA8
irq 15
[ 128.414982] scsi5 : ata_piix
[ 128.723123] ACPI Error (dsopcode-0481): Attempt to CreateField of
length zero [20060707]
[ 128.731348] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.RATA] (Node ffff810001ff74d0), AE_AML_OPERAND_VALUE
[ 128.743887] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.CHN0.DRV0._GTF] (Node ffff810001ff7830),
AE_AML_OPERAND_VALUE
[ 128.757290] ata5.00: ATAPI, max UDMA/33
[ 128.915451] ACPI Error (dsopcode-0481): Attempt to CreateField of
length zero [20060707]
[ 128.923670] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.RATA] (Node ffff810001ff74d0), AE_AML_OPERAND_VALUE
[ 128.936209] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.CHN0.DRV0._GTF] (Node ffff810001ff7830),
AE_AML_OPERAND_VALUE
[ 128.949614] ata5.01: ATAPI, max UDMA/33
[ 158.925558] ata5.00: qc timeout (cmd 0xef)
[ 158.929692] ata5.00: failed to set xfermode (err_mask=0x4)
[ 158.935207] ata5.00: limiting speed to UDMA/25
[ 158.939682] ata5: failed to recover some devices, retrying in 5 secs
[ 164.247317] ACPI Error (dsopcode-0481): Attempt to CreateField of
length zero [20060707]
[ 164.255540] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.RATA] (Node ffff810001ff74d0), AE_AML_OPERAND_VALUE
[ 164.268079] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.CHN0.DRV0._GTF] (Node ffff810001ff7830),
AE_AML_OPERAND_VALUE
[ 164.433250] ACPI Error (dsopcode-0481): Attempt to CreateField of
length zero [20060707]
[ 164.441472] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.RATA] (Node ffff810001ff74d0), AE_AML_OPERAND_VALUE
[ 164.454010] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.CHN0.DRV0._GTF] (Node ffff810001ff7830),
AE_AML_OPERAND_VALUE
[ 194.440214] ata5.00: qc timeout (cmd 0xef)
[ 194.444350] ata5.00: failed to set xfermode (err_mask=0x4)
[ 194.455118] ata5.00: limiting speed to PIO0
[ 194.459336] ata5: failed to recover some devices, retrying in 5 secs
[ 199.766792] ACPI Error (dsopcode-0481): Attempt to CreateField of
length zero [20060707]
[ 199.775020] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.RATA] (Node ffff810001ff74d0), AE_AML_OPERAND_VALUE
[ 199.787558] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.CHN0.DRV0._GTF] (Node ffff810001ff7830),
AE_AML_OPERAND_VALUE
[ 199.952400] ACPI Error (dsopcode-0481): Attempt to CreateField of
length zero [20060707]
[ 199.960624] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.RATA] (Node ffff810001ff74d0), AE_AML_OPERAND_VALUE
[ 199.973161] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.CHN0.DRV0._GTF] (Node ffff810001ff7830),
AE_AML_OPERAND_VALUE
[ 229.958667] ata5.00: qc timeout (cmd 0xef)
[ 229.962801] ata5.00: failed to set xfermode (err_mask=0x4)
[ 229.968322] ata5.00: disabled
[ 229.971325] ata5: failed to recover some devices, retrying in 5 secs
[ 234.974450] ata5.01: failed to set xfermode (err_mask=0x40)
[ 234.980058] ata5.01: limiting speed to UDMA/25
[ 234.984531] ata5: failed to recover some devices, retrying in 5 secs
[ 240.289500] ACPI Error (dsopcode-0481): Attempt to CreateField of
length zero [20060707]
[ 240.297721] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.RATA] (Node ffff810001ff74d0), AE_AML_OPERAND_VALUE
[ 240.310260] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.CHN0.DRV1._GTF] (Node ffff810001ff77d0),
AE_AML_OPERAND_VALUE
[ 240.475708] ACPI Error (dsopcode-0481): Attempt to CreateField of
length zero [20060707]
[ 240.483930] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.RATA] (Node ffff810001ff74d0), AE_AML_OPERAND_VALUE
[ 240.496469] ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.IDE0.CHN0.DRV1._GTF] (Node ffff810001ff77d0),
AE_AML_OPERAND_VALUE
[ 240.509872] ata5.01: configured for UDMA/25
[ 240.514094] scsi6 : ata_piix
[ 241.733617] ATA: abnormal status 0x7F on port 0x177
[ 241.739526] scsi 5:0:1:0: CD-ROM _NEC DVD_RW ND-3520AW
3.04 PQ: 0 ANSI: 5
[ 241.751812] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 241.758640] Uniform CD-ROM driver Revision: 3.20
[ 241.763352] sr 5:0:1:0: Attached scsi generic sg5 type 5
next reply other threads:[~2006-12-01 16:19 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-12-01 16:19 Berck E. Nash [this message]
2007-02-27 15:01 ` libata Intel PIIX/ICH fails to detect both PATA drives, spews ACPI errors Tejun Heo
2007-03-11 12:40 ` Berck E. Nash
2007-03-12 7:09 ` Tejun Heo
2007-03-12 12:02 ` Berck E. Nash
2007-03-12 12:25 ` Tejun Heo
2007-03-12 23:40 ` Berck E. Nash
2007-03-13 1:53 ` Mark Lord
2007-04-28 16:20 ` Berck E. Nash
2007-03-14 1:46 ` Berck E. Nash
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=45705618.2020608@gmail.com \
--to=flyboy@gmail.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).