* Slow SATA detection on bootup
@ 2006-10-25 18:45 Stephen Hemminger
2006-10-25 19:06 ` Jeff Garzik
2006-12-16 17:02 ` Jeff Garzik
0 siblings, 2 replies; 4+ messages in thread
From: Stephen Hemminger @ 2006-10-25 18:45 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-ide
This laptop has long timeouts during bootup. Something is
wrong. This is a Sony VAIO NG170. On a positive note suspend works.
Here is the console log during the 40 seconds of dead time.
[ 2.942000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.942000] ata1: SATA max UDMA/133 cmd 0x18B0 ctl 0x18A6 bmdma 0x1890 irq 225
[ 2.942000] ata2: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 225
[ 2.942000] scsi0 : ata_piix
[ 3.094000] ata1.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32)
[ 3.094000] ata1.00: ata1: dev 0 multi count 16
[ 3.097000] ata1.00: configured for UDMA/100
[ 3.097000] scsi1 : ata_piix
[ 10.144000] ata2: port is slow to respond, please be patient
[ 33.104000] ata2: port failed to respond (30 secs)
[ 33.255000] ata2: SRST failed (status 0xFF)
[ 33.255000] ata2: SRST failed (err_mask=0x100)
[ 33.255000] ata2: softreset failed, retrying in 5 secs
[ 38.407000] ata2: SRST failed (status 0xFF)
[ 38.407000] ata2: SRST failed (err_mask=0x100)
[ 38.407000] ata2: softreset failed, retrying in 5 secs
[ 43.560000] ata2: SRST failed (status 0xFF)
[ 43.560000] ata2: SRST failed (err_mask=0x100)
[ 43.560000] ata2: reset failed, giving up
[ 43.560000] Vendor: ATA Model: FUJITSU MHV2120B Rev: 0000
[ 43.561000] Type: Direct-Access ANSI SCSI revision: 05
[ 43.567000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
Full log:
[ 0.000000] Linux version 2.6.18.1 (shemminger@sony-laptop) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Fri Oct 20 15:14:44 PDT 2006
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f690000 (usable)
[ 0.000000] BIOS-e820: 000000003f690000 - 000000003f698000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003f698000 - 000000003f700000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] Warning only 896MB will be used.
[ 0.000000] Use a HIGHMEM enabled kernel.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f71b0
[ 0.000000] On node 0 totalpages: 229376
[ 0.000000] DMA zone: 4096 pages, LIFO batch:0
[ 0.000000] Normal zone: 225280 pages, LIFO batch:31
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 PTLTD ) @ 0x000f70e0
[ 0.000000] ACPI: RSDT (v001 SONY J4 0x20060907 PTL 0x00000000) @ 0x3f6916ca
[ 0.000000] ACPI: FADT (v002 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697e48
[ 0.000000] ACPI: MADT (v001 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697ecc
[ 0.000000] ACPI: MCFG (v001 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697f34
[ 0.000000] ACPI: MADT (v001 SONY J4 0x20060907 PTL 0x00000000) @ 0x3f697f70
[ 0.000000] ACPI: BOOT (v001 SONY J4 0x20060907 PTL 0x00000001) @ 0x3f697fd8
[ 0.000000] ACPI: SSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x3f69210b
[ 0.000000] ACPI: SSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x3f69170a
[ 0.000000] ACPI: DSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: 2 duplicate APIC table ignored.
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:14 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 6:14 APIC version 20
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] Detected 1596.085 MHz processor.
[ 17.971836] Built 1 zonelists. Total pages: 229376
[ 17.971839] Kernel command line: root=/dev/sda1 ro
[ 17.972048] mapped APIC to ffffd000 (fee00000)
[ 17.972051] mapped IOAPIC to ffffc000 (fec00000)
[ 17.972054] Enabling fast FPU save and restore... done.
[ 17.972057] Enabling unmasked SIMD FPU exception support... done.
[ 17.972061] Initializing CPU#0
[ 17.972126] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 17.973647] Console: colour VGA+ 80x25
[ 17.976113] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 17.976569] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 17.994368] Memory: 902104k/917504k available (1408k kernel code, 14816k reserved, 559k data, 196k init, 0k highmem)
[ 17.994449] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 18.054045] Calibrating delay using timer specific routine.. 3194.44 BogoMIPS (lpj=1597223)
[ 18.054199] Mount-cache hash table entries: 512
[ 18.054351] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[ 18.054361] CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[ 18.054368] monitor/mwait feature present.
[ 18.054422] using mwait in idle threads.
[ 18.054476] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 18.054564] CPU: L2 cache: 2048K
[ 18.054616] CPU: Physical Processor ID: 0
[ 18.054668] CPU: Processor Core ID: 0
[ 18.054720] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
[ 18.054729] Compat vDSO mapped to ffffe000.
[ 18.054792] Checking 'hlt' instruction... OK.
[ 18.058140] SMP alternatives: switching to UP code
[ 18.058293] ACPI: Core revision 20060707
[ 18.091651] CPU0: Intel Genuine Intel(R) CPU T2050 @ 1.60GHz stepping 08
[ 18.091832] SMP alternatives: switching to SMP code
[ 18.092007] Booting processor 1/1 eip 3000
[ 18.102538] Initializing CPU#1
[ 18.162923] Calibrating delay using timer specific routine.. 3191.58 BogoMIPS (lpj=1595793)
[ 18.162930] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[ 18.162938] CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[ 18.162943] monitor/mwait feature present.
[ 18.162946] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 18.162949] CPU: L2 cache: 2048K
[ 18.162951] CPU: Physical Processor ID: 0
[ 18.162953] CPU: Processor Core ID: 1
[ 18.162955] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
[ 18.163353] CPU1: Intel Genuine Intel(R) CPU T2050 @ 1.60GHz stepping 08
[ 18.163934] Total of 2 processors activated (6386.03 BogoMIPS).
[ 18.164188] ENABLING IO-APIC IRQs
[ 18.164426] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 18.275811] checking TSC synchronization across 2 CPUs: passed.
[ 0.000955] Brought up 2 CPUs
[ 0.284715] migration_cost=53
[ 0.284964] checking if image is initramfs... it is
[ 0.678499] Freeing initrd memory: 3914k freed
[ 0.678916] NET: Registered protocol family 16
[ 0.679050] ACPI: bus type pci registered
[ 0.679108] PCI: Using MMCONFIG
[ 0.680097] Setting up standard PCI resources
[ 0.699770] ACPI: Interpreter enabled
[ 0.699825] ACPI: Using IOAPIC for interrupt routing
[ 0.712680] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.712738] PCI: Probing PCI hardware (bus 00)
[ 0.719670] Boot video device is 0000:00:02.0
[ 0.720318] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[ 0.721506] PCI: Transparent bridge - 0000:00:1e.0
[ 0.721623] PCI: Bus #09 (-#0c) is hidden behind transparent bridge #08 (-#09) (try 'pci=assign-busses')
[ 0.721701] Please report the result to linux-kernel to fix this permanently
[ 0.721815] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.729700] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.729986] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.730273] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.731404] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.732533] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15)
[ 0.733247] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 *3 4 5 6 7 11 12 14 15)
[ 0.733932] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.734674] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.735432] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.736212] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.736976] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 *4 5 6 7 10 12 14 15)
[ 0.737672] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 11 12 14 15)
[ 0.738177] ACPI: Embedded Controller [EC] (gpe 23) interrupt mode.
[ 0.743243] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.743312] pnp: PnP ACPI init
[ 0.753240] pnp: PnP ACPI: found 9 devices
[ 0.753343] PCI: Using ACPI for IRQ routing
[ 0.753397] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.753969] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[ 0.754032] PCI: Bridge: 0000:00:1c.0
[ 0.754087] IO window: 2000-2fff
[ 0.754151] MEM window: d6000000-d7ffffff
[ 0.754207] PREFETCH window: d0000000-d1ffffff
[ 0.754266] PCI: Bridge: 0000:00:1c.1
[ 0.754321] IO window: 3000-3fff
[ 0.754376] MEM window: d8000000-d9ffffff
[ 0.754433] PREFETCH window: d2000000-d3ffffff
[ 0.754491] PCI: Bridge: 0000:00:1c.2
[ 0.754545] IO window: 4000-4fff
[ 0.754602] MEM window: da000000-dbffffff
[ 0.754658] PREFETCH window: d4000000-d5ffffff
[ 0.754725] PCI: Bus 9, cardbus bridge: 0000:08:03.0
[ 0.754781] IO window: 00005000-000050ff
[ 0.754839] IO window: 00005400-000054ff
[ 0.754896] PREFETCH window: 50000000-51ffffff
[ 0.754954] MEM window: 52000000-53ffffff
[ 0.755011] PCI: Bridge: 0000:00:1e.0
[ 0.755065] IO window: 5000-5fff
[ 0.755131] MEM window: dc000000-dc0fffff
[ 0.755187] PREFETCH window: 50000000-51ffffff
[ 0.755264] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
[ 0.755374] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.755396] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 177
[ 0.755504] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.755524] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185
[ 0.755632] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.755642] PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
[ 0.755703] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.755718] PCI: Enabling device 0000:08:03.0 (0000 -> 0003)
[ 0.755777] ACPI: PCI Interrupt 0000:08:03.0[A] -> GSI 16 (level, low) -> IRQ 177
[ 0.755888] PCI: Setting latency timer of device 0000:08:03.0 to 64
[ 0.755915] NET: Registered protocol family 2
[ 0.769144] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.769338] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 0.770560] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.771234] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.771295] TCP reno registered
[ 0.771542] Simple Boot Flag at 0x36 set to 0x1
[ 0.772608] Initializing Cryptographic API
[ 0.772670] io scheduler noop registered
[ 0.772759] io scheduler anticipatory registered (default)
[ 0.772885] io scheduler deadline registered
[ 0.772985] io scheduler cfq registered
[ 0.773309] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.773359] assign_interrupt_mode Found MSI capability
[ 0.773473] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.773515] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.773550] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.773594] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.773643] assign_interrupt_mode Found MSI capability
[ 0.773742] Allocate Port Service[0000:00:1c.1:pcie00]
[ 0.773783] Allocate Port Service[0000:00:1c.1:pcie02]
[ 0.773817] Allocate Port Service[0000:00:1c.1:pcie03]
[ 0.773863] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.773912] assign_interrupt_mode Found MSI capability
[ 0.774011] Allocate Port Service[0000:00:1c.2:pcie00]
[ 0.774048] Allocate Port Service[0000:00:1c.2:pcie02]
[ 0.774085] Allocate Port Service[0000:00:1c.2:pcie03]
[ 0.797628] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 0.798806] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 0.798983] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 0.799042] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 0.799372] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.802193] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.805641] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.806389] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.807395] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.809028] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.809985] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.810103] mice: PS/2 mouse device common for all mice
[ 0.810253] TCP bic registered
[ 0.810943] NET: Registered protocol family 1
[ 0.811008] Using IPI No-Shortcut mode
[ 0.811377] Time: tsc clocksource has been installed.
[ 0.811473] ACPI: (supports S0 S3 S4 S5)
[ 0.811856] Freeing unused kernel memory: 196k freed
[ 0.862634] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 0.863294] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 0.864590] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 0.864744] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 0.865429] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 0.865786] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 0.866254] ACPI: CPU1 (power states: C1[C1] C2[C2])
[ 0.866408] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 0.868132] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[ 0.869086] ACPI: Thermal Zone [TZ00] (36 C)
[ 0.870127] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[ 0.871051] ACPI: Thermal Zone [TZ01] (36 C)
[ 1.051000] Time: acpi_pm clocksource has been installed.
[ 1.409000] ICH7: IDE controller at PCI slot 0000:00:1f.1
[ 1.409000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 185
[ 1.409000] ICH7: chipset revision 2
[ 1.409000] ICH7: not 100% native mode: will probe irqs later
[ 1.409000] ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio
[ 1.410000] Probing IDE interface ide0...
[ 1.600000] input: AT Translated Set 2 keyboard as /class/input/input0
[ 2.082000] hda: PIONEER DVD-RW DVR-K16D, ATAPI CD/DVD-ROM drive
[ 2.695000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 2.703000] hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
[ 2.704000] Uniform CD-ROM driver Revision: 3.20
[ 2.785000] SCSI subsystem initialized
[ 2.789000] libata version 2.00 loaded.
[ 2.791000] ata_piix 0000:00:1f.2: version 2.00
[ 2.791000] ata_piix 0000:00:1f.2: MAP [ P0 P2 XX XX ]
[ 2.791000] ata_piix 0000:00:1f.2: invalid MAP value 0
[ 2.942000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 225
[ 2.942000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.942000] ata1: SATA max UDMA/133 cmd 0x18B0 ctl 0x18A6 bmdma 0x1890 irq 225
[ 2.942000] ata2: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 225
[ 2.942000] scsi0 : ata_piix
[ 3.094000] ata1.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32)
[ 3.094000] ata1.00: ata1: dev 0 multi count 16
[ 3.097000] ata1.00: configured for UDMA/100
[ 3.097000] scsi1 : ata_piix
[ 10.144000] ata2: port is slow to respond, please be patient
[ 33.104000] ata2: port failed to respond (30 secs)
[ 33.255000] ata2: SRST failed (status 0xFF)
[ 33.255000] ata2: SRST failed (err_mask=0x100)
[ 33.255000] ata2: softreset failed, retrying in 5 secs
[ 38.407000] ata2: SRST failed (status 0xFF)
[ 38.407000] ata2: SRST failed (err_mask=0x100)
[ 38.407000] ata2: softreset failed, retrying in 5 secs
[ 43.560000] ata2: SRST failed (status 0xFF)
[ 43.560000] ata2: SRST failed (err_mask=0x100)
[ 43.560000] ata2: reset failed, giving up
[ 43.560000] Vendor: ATA Model: FUJITSU MHV2120B Rev: 0000
[ 43.561000] Type: Direct-Access ANSI SCSI revision: 05
[ 43.567000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 43.567000] sda: Write Protect is off
[ 43.567000] sda: Mode Sense: 00 3a 00 00
[ 43.567000] SCSI device sda: drive cache: write back
[ 43.568000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 43.568000] sda: Write Protect is off
[ 43.568000] sda: Mode Sense: 00 3a 00 00
[ 43.568000] SCSI device sda: drive cache: write back
[ 43.568000] sda: sda1 sda2 sda3
[ 43.924000] sd 0:0:0:0: Attached scsi disk sda
[ 44.182000] usbcore: registered new driver usbfs
[ 44.182000] usbcore: registered new driver hub
[ 44.188000] USB Universal Host Controller Interface driver v3.0
[ 44.188000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 233
[ 44.188000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 44.188000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 44.188000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 44.188000] uhci_hcd 0000:00:1d.0: irq 233, io base 0x00001820
[ 44.189000] usb usb1: configuration #1 chosen from 1 choice
[ 44.189000] hub 1-0:1.0: USB hub found
[ 44.189000] hub 1-0:1.0: 2 ports detected
[ 44.200000] ieee1394: Initialized config rom entry `ip1394'
[ 44.290000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 169
[ 44.291000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 44.291000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 44.291000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 44.291000] uhci_hcd 0000:00:1d.1: irq 169, io base 0x00001840
[ 44.291000] usb usb2: configuration #1 chosen from 1 choice
[ 44.291000] hub 2-0:1.0: USB hub found
[ 44.291000] hub 2-0:1.0: 2 ports detected
[ 44.392000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 233
[ 44.393000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 44.393000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 44.393000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
[ 44.393000] ehci_hcd 0000:00:1d.7: debug port 1
[ 44.393000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 44.393000] ehci_hcd 0000:00:1d.7: irq 233, io mem 0xdc444000
[ 44.397000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 44.397000] usb usb3: configuration #1 chosen from 1 choice
[ 44.397000] hub 3-0:1.0: USB hub found
[ 44.397000] hub 3-0:1.0: 6 ports detected
[ 44.499000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
[ 44.499000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 44.499000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 44.499000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 44.499000] uhci_hcd 0000:00:1d.2: irq 185, io base 0x00001860
[ 44.499000] usb usb4: configuration #1 chosen from 1 choice
[ 44.499000] hub 4-0:1.0: USB hub found
[ 44.499000] hub 4-0:1.0: 2 ports detected
[ 44.601000] PCI: Enabling device 0000:08:03.1 (0000 -> 0002)
[ 44.601000] ACPI: PCI Interrupt 0000:08:03.1[A] -> GSI 16 (level, low) -> IRQ 177
[ 44.601000] PCI: Setting latency timer of device 0000:08:03.1 to 64
[ 44.658000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[177] MMIO=[dc005000-dc0057ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 44.670000] Probing IDE interface ide1...
[ 45.211000] Attempting manual resume
[ 45.223000] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 45.223000] EXT3-fs: write access will be enabled during recovery.
[ 45.250000] kjournald starting. Commit interval 5 seconds
[ 45.250000] EXT3-fs: recovery complete.
[ 45.251000] EXT3-fs: mounted filesystem with ordered data mode.
[ 45.916000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0800460302320543]
[ 50.698000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 51.622000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 51.705000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 51.724000] Linux agpgart interface v0.101 (c) Dave Jones
[ 51.734000] agpgart: Detected an Intel 945GM Chipset.
[ 51.735000] agpgart: Detected 7932K stolen memory.
[ 51.753000] agpgart: AGP aperture is 256M @ 0xc0000000
[ 51.824000] input: PC Speaker as /class/input/input1
[ 51.931000] Real Time Clock Driver v1.12ac
[ 52.325000] input: PS/2 Mouse as /class/input/input2
[ 52.345000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
[ 52.387000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 177
[ 52.387000] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 52.387000] sky2 v1.5 addr 0xd6000000 irq 177 Yukon-FE (0xb7) rev 1
[ 52.388000] sky2 eth0: addr 00:13:a9:7d:aa:6f
[ 52.442000] ts: Compaq touchscreen protocol output
[ 52.649000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 58
[ 52.649000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 52.699000] sky2 eth0: enabling interface
[ 52.741000] hda_codec: Unknown model for ALC262, trying auto-probe from BIOS...
[ 52.967000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[ 52.967000] ieee1394: sbp2: Try serialize_io=0 for better performance
[ 53.023000] Adding 2104504k swap on /dev/sda2. Priority:-1 extents:1 across:2104504k
[ 53.067000] EXT3 FS on sda1, internal journal
[ 53.677000] kjournald starting. Commit interval 5 seconds
[ 53.678000] EXT3 FS on sda3, internal journal
[ 53.679000] EXT3-fs: mounted filesystem with ordered data mode.
[ 53.809000] NET: Registered protocol family 17
[ 54.587000] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control none
[ 57.064000] NET: Registered protocol family 10
[ 57.064000] lo: Disabled Privacy Extensions
[ 57.064000] IPv6 over IPv4 tunneling driver
[ 58.956000] ACPI: AC Adapter [ADP1] (on-line)
[ 59.006000] ACPI: Battery Slot [BAT0] (battery present)
[ 59.021000] ACPI: Lid Switch [LID0]
[ 59.022000] ACPI: Power Button (CM) [PWRB]
[ 59.067000] Using specific hotkey driver
[ 59.138000] ibm_acpi: ec object not found
[ 59.176000] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 59.186000] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 62.645000] [drm] Initialized drm 1.0.1 20051102
[ 62.660000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 177
[ 62.662000] [drm] Initialized i915 1.5.0 20060119 on minor 0
[ 63.033000] sonypi: Sony Programmable I/O Controller Driver v1.26.
[ 63.036000] sonypi: detected type3 model, verbose = 0, fnkeyinit = off, camera = off, compat = off, mask = 0xffffffff, useinput = on, acpi = on
[ 63.036000] sonypi: enabled at irq=11, port1=0x1080, port2=0x1084
[ 63.036000] sonypi: device allocated minor is 63
[ 63.037000] input: Sony Vaio Jogdial as /class/input/input4
[ 63.047000] input: Sony Vaio Keys as /class/input/input5
[ 63.176000] sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646)
[ 63.218000] sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 657)
[ 63.260000] sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 659)
[ 63.307000] sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646)
[ 67.132000] psmouse.c: GlidePoint at isa0060/serio4/input0 lost synchronization, throwing 1 bytes away.
[ 67.256000] eth0: no IPv6 routers present
[ 67.640000] psmouse.c: resync failed, issuing reconnect request
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Slow SATA detection on bootup
2006-10-25 18:45 Slow SATA detection on bootup Stephen Hemminger
@ 2006-10-25 19:06 ` Jeff Garzik
2006-10-25 21:07 ` Stephen Hemminger
2006-12-16 17:02 ` Jeff Garzik
1 sibling, 1 reply; 4+ messages in thread
From: Jeff Garzik @ 2006-10-25 19:06 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: linux-ide
On Wed, Oct 25, 2006 at 11:45:04AM -0700, Stephen Hemminger wrote:
> This laptop has long timeouts during bootup. Something is
> wrong. This is a Sony VAIO NG170. On a positive note suspend works.
>
> Here is the console log during the 40 seconds of dead time.
What are results from the latest 2.6.19-rcX-gitX, and from the latest -mm?
Jeff
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Slow SATA detection on bootup
2006-10-25 19:06 ` Jeff Garzik
@ 2006-10-25 21:07 ` Stephen Hemminger
0 siblings, 0 replies; 4+ messages in thread
From: Stephen Hemminger @ 2006-10-25 21:07 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-ide
On Wed, 25 Oct 2006 15:06:20 -0400
Jeff Garzik <jeff@garzik.org> wrote:
> On Wed, Oct 25, 2006 at 11:45:04AM -0700, Stephen Hemminger wrote:
> > This laptop has long timeouts during bootup. Something is
> > wrong. This is a Sony VAIO NG170. On a positive note suspend works.
> >
> > Here is the console log during the 40 seconds of dead time.
>
> What are results from the latest 2.6.19-rcX-gitX, and from the latest -mm?
>
> Jeff
>
Same problem with current git tree.
[ 1.339696] ata4: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 19
[ 1.339766] scsi2 : ata_piix
[ 1.492243] ata3.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32)
[ 1.492325] ata3.00: ata3: dev 0 multi count 16
[ 1.495405] ata3.00: configured for UDMA/100
[ 1.495461] scsi3 : ata_piix
[ 8.530407] ata4: port is slow to respond, please be patient (Status 0xff)
[ 31.505574] ata4: port failed to respond (30 secs, Status 0xff)
[ 31.656404] ata4: SRST failed (status 0xFF)
[ 31.656459] ata4: SRST failed (err_mask=0x100)
[ 31.656514] ata4: softreset failed, retrying in 5 secs
[ 36.804622] ata4: SRST failed (status 0xFF)
[ 36.804681] ata4: SRST failed (err_mask=0x100)
[ 36.804737] ata4: softreset failed, retrying in 5 secs
[ 41.951843] ata4: SRST failed (status 0xFF)
[ 41.951898] ata4: SRST failed (err_mask=0x100)
[ 41.951952] ata4: reset failed, giving up
It is Intel ICH7 chips, here are the relevant portions of lspci
0000:00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Sony Corporation: Unknown device 8212
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 1810 [size=16]
00: 86 80 df 27 05 00 80 02 02 8a 01 01 00 00 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: 11 18 00 00 00 00 00 00 00 00 00 00 4d 10 12 82
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00
0000:00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controllers cc=IDE (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Sony Corporation: Unknown device 8212
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 18b0 [size=8]
Region 1: I/O ports at 18a4 [size=4]
Region 2: I/O ports at 18a8 [size=8]
Region 3: I/O ports at 18a0 [size=4]
Region 4: I/O ports at 1890 [size=16]
Region 5: Memory at dc444400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 c4 27 07 00 b0 02 02 8f 01 01 00 00 00 00
10: b1 18 00 00 a5 18 00 00 a9 18 00 00 a1 18 00 00
20: 91 18 00 00 00 44 44 dc 00 00 00 00 4d 10 12 82
30: 00 00 00 00 70 00 00 00 00 00 00 00 0a 02 00 00
Full log.
[ 0.000000] Linux version 2.6.19-rc3 (shemminger@sony-laptop) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #3 SMP PREEMPT Wed Oct 25 13:47:23 PDT 2006
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f690000 (usable)
[ 0.000000] BIOS-e820: 000000003f690000 - 000000003f698000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003f698000 - 000000003f700000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] 118MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f71b0
[ 0.000000] Entering add_active_range(0, 0, 259728) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 259728
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 259728
[ 0.000000] On node 0 totalpages: 259728
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 237 pages used for memmap
[ 0.000000] HighMem zone: 30115 pages, LIFO batch:7
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 PTLTD ) @ 0x000f70e0
[ 0.000000] ACPI: RSDT (v001 SONY J4 0x20060907 PTL 0x00000000) @ 0x3f6916ca
[ 0.000000] ACPI: FADT (v002 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697e48
[ 0.000000] ACPI: MADT (v001 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697ecc
[ 0.000000] ACPI: MCFG (v001 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697f34
[ 0.000000] ACPI: MADT (v001 SONY J4 0x20060907 PTL 0x00000000) @ 0x3f697f70
[ 0.000000] ACPI: BOOT (v001 SONY J4 0x20060907 PTL 0x00000001) @ 0x3f697fd8
[ 0.000000] ACPI: SSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x3f69210b
[ 0.000000] ACPI: SSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x3f69170a
[ 0.000000] ACPI: DSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: 2 duplicate APIC table ignored.
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:14 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 6:14 APIC version 20
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] Detected 1596.091 MHz processor.
[ 13.409916] Built 1 zonelists. Total pages: 257699
[ 13.409921] Kernel command line: root=/dev/sda1 ro
[ 13.410111] mapped APIC to ffffd000 (fee00000)
[ 13.410114] mapped IOAPIC to ffffc000 (fec00000)
[ 13.410117] Enabling fast FPU save and restore... done.
[ 13.410120] Enabling unmasked SIMD FPU exception support... done.
[ 13.410123] Initializing CPU#0
[ 13.410191] CPU 0 irqstacks, hard=c03a4000 soft=c03ac000
[ 13.410195] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 13.411710] Console: colour VGA+ 80x25
[ 13.414446] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 13.414874] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 13.441204] Memory: 1022472k/1038912k available (1567k kernel code, 15808k reserved, 611k data, 204k init, 121408k highmem)
[ 13.441294] virtual kernel memory layout:
[ 13.441296] fixmap : 0xfff4f000 - 0xfffff000 ( 704 kB)
[ 13.441297] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 13.441299] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 13.441300] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 13.441302] .init : 0xc036c000 - 0xc039f000 ( 204 kB)
[ 13.441304] .data : 0xc0287d89 - 0xc0320b30 ( 611 kB)
[ 13.441305] .text : 0xc0100000 - 0xc0287d89 (1567 kB)
[ 13.441738] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 13.501101] Calibrating delay using timer specific routine.. 3194.47 BogoMIPS (lpj=1597238)
[ 13.501257] Mount-cache hash table entries: 512
[ 13.501413] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[ 13.501421] monitor/mwait feature present.
[ 13.501475] using mwait in idle threads.
[ 13.501531] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 13.501617] CPU: L2 cache: 2048K
[ 13.501668] CPU: Physical Processor ID: 0
[ 13.501720] CPU: Processor Core ID: 0
[ 13.501773] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
[ 13.501783] Compat vDSO mapped to ffffe000.
[ 13.501846] Checking 'hlt' instruction... OK.
[ 13.505201] SMP alternatives: switching to UP code
[ 13.505353] ACPI: Core revision 20060707
[ 13.544920] CPU0: Intel Genuine Intel(R) CPU T2050 @ 1.60GHz stepping 08
[ 13.545109] SMP alternatives: switching to SMP code
[ 13.545271] Booting processor 1/1 eip 3000
[ 13.545326] CPU 1 irqstacks, hard=c03a5000 soft=c03ad000
[ 13.555858] Initializing CPU#1
[ 13.615972] Calibrating delay using timer specific routine.. 3191.59 BogoMIPS (lpj=1595795)
[ 13.615979] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[ 13.615985] monitor/mwait feature present.
[ 13.615989] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 13.615991] CPU: L2 cache: 2048K
[ 13.615993] CPU: Physical Processor ID: 0
[ 13.615995] CPU: Processor Core ID: 1
[ 13.615997] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
[ 13.616464] CPU1: Intel Genuine Intel(R) CPU T2050 @ 1.60GHz stepping 08
[ 13.617044] Total of 2 processors activated (6386.06 BogoMIPS).
[ 13.617298] ENABLING IO-APIC IRQs
[ 13.617548] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 13.728856] checking TSC synchronization across 2 CPUs: passed.
[ 0.000962] Brought up 2 CPUs
[ 0.207488] migration_cost=73
[ 0.207750] checking if image is initramfs... it is
[ 0.570873] Freeing initrd memory: 3604k freed
[ 0.571302] NET: Registered protocol family 16
[ 0.571451] ACPI: bus type pci registered
[ 0.571513] PCI: Using MMCONFIG
[ 0.572501] Setting up standard PCI resources
[ 0.593906] ACPI: Interpreter enabled
[ 0.593961] ACPI: Using IOAPIC for interrupt routing
[ 0.606808] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.606869] PCI: Probing PCI hardware (bus 00)
[ 0.613788] Boot video device is 0000:00:02.0
[ 0.614281] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.614341] PCI quirk: region 1180-11bf claimed by ICH6 GPIO
[ 0.614443] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[ 0.615480] PCI: Transparent bridge - 0000:00:1e.0
[ 0.615597] PCI: Bus #09 (-#0c) is hidden behind transparent bridge #08 (-#09) (try 'pci=assign-busses')
[ 0.615676] Please report the result to linux-kernel to fix this permanently
[ 0.615788] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.623927] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.624216] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.624503] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.625666] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.626809] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15)
[ 0.627515] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 *3 4 5 6 7 11 12 14 15)
[ 0.628207] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.628954] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.629694] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.630467] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.631238] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 *4 5 6 7 10 12 14 15)
[ 0.631934] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 11 12 14 15)
[ 0.636478] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.636541] pnp: PnP ACPI init
[ 0.645610] pnp: PnP ACPI: found 9 devices
[ 0.645694] intel_rng: FWH not detected
[ 0.645889] SCSI subsystem initialized
[ 0.645966] PCI: Using ACPI for IRQ routing
[ 0.646021] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.646602] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[ 0.646664] PCI: Bridge: 0000:00:1c.0
[ 0.646719] IO window: 2000-2fff
[ 0.646776] MEM window: d6000000-d7ffffff
[ 0.646832] PREFETCH window: d0000000-d1ffffff
[ 0.646890] PCI: Bridge: 0000:00:1c.1
[ 0.646943] IO window: 3000-3fff
[ 0.646999] MEM window: d8000000-d9ffffff
[ 0.647056] PREFETCH window: d2000000-d3ffffff
[ 0.647114] PCI: Bridge: 0000:00:1c.2
[ 0.647169] IO window: 4000-4fff
[ 0.647230] MEM window: da000000-dbffffff
[ 0.647292] PREFETCH window: d4000000-d5ffffff
[ 0.647356] PCI: Bus 9, cardbus bridge: 0000:08:03.0
[ 0.647412] IO window: 00005000-000050ff
[ 0.647469] IO window: 00005400-000054ff
[ 0.647526] PREFETCH window: 50000000-51ffffff
[ 0.647584] MEM window: 52000000-53ffffff
[ 0.647641] PCI: Bridge: 0000:00:1e.0
[ 0.647696] IO window: 5000-5fff
[ 0.647751] MEM window: dc000000-dc0fffff
[ 0.647807] PREFETCH window: 50000000-51ffffff
[ 0.647885] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
[ 0.647994] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.648015] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 17
[ 0.648124] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.648144] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 0.648258] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.648268] PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
[ 0.648328] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.648343] PCI: Enabling device 0000:08:03.0 (0000 -> 0003)
[ 0.648402] ACPI: PCI Interrupt 0000:08:03.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 0.648513] PCI: Setting latency timer of device 0000:08:03.0 to 64
[ 0.648542] NET: Registered protocol family 2
[ 0.658276] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.658476] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 0.659696] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.660356] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.660415] TCP reno registered
[ 0.660686] Simple Boot Flag at 0x36 set to 0x1
[ 0.661253] highmem bounce pool size: 64 pages
[ 0.661456] io scheduler noop registered
[ 0.661543] io scheduler anticipatory registered (default)
[ 0.661665] io scheduler deadline registered
[ 0.661760] io scheduler cfq registered
[ 0.662077] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.662127] assign_interrupt_mode Found MSI capability
[ 0.662239] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.662276] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.662307] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.662409] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.662457] assign_interrupt_mode Found MSI capability
[ 0.662550] Allocate Port Service[0000:00:1c.1:pcie00]
[ 0.662584] Allocate Port Service[0000:00:1c.1:pcie02]
[ 0.662615] Allocate Port Service[0000:00:1c.1:pcie03]
[ 0.662710] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.662759] assign_interrupt_mode Found MSI capability
[ 0.662853] Allocate Port Service[0000:00:1c.2:pcie00]
[ 0.662886] Allocate Port Service[0000:00:1c.2:pcie02]
[ 0.662922] Allocate Port Service[0000:00:1c.2:pcie03]
[ 0.685392] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 0.686530] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 0.686708] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 0.686768] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 0.687072] libata version 2.00 loaded.
[ 0.687143] ata_piix 0000:00:1f.1: version 2.00ac6
[ 0.687157] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 0.687280] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 0.687328] ata1: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1810 irq 14
[ 0.688305] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[ 0.688385] scsi0 : ata_piix
[ 1.002858] ata1.00: ATAPI, max UDMA/33
[ 1.166641] ata1.00: configured for UDMA/33
[ 1.166705] scsi1 : ata_piix
[ 1.166813] ata2: port disabled. ignoring.
[ 1.178390] ATA: abnormal status 0xFF on port 0x177
[ 1.187849] scsi 0:0:0:0: CD-ROM PIONEER DVD-RW DVR-K16D 1.00 PQ: 0 ANSI: 5
[ 1.188008] ata_piix 0000:00:1f.2: MAP [ P0 P2 XX XX ]
[ 1.188224] ata_piix 0000:00:1f.2: invalid MAP value 0
[ 1.339464] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 1.339584] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 1.339610] ata3: SATA max UDMA/133 cmd 0x18B0 ctl 0x18A6 bmdma 0x1890 irq 19
[ 1.339696] ata4: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 19
[ 1.339766] scsi2 : ata_piix
[ 1.492243] ata3.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32)
[ 1.492325] ata3.00: ata3: dev 0 multi count 16
[ 1.495405] ata3.00: configured for UDMA/100
[ 1.495461] scsi3 : ata_piix
[ 8.530407] ata4: port is slow to respond, please be patient (Status 0xff)
[ 31.505574] ata4: port failed to respond (30 secs, Status 0xff)
[ 31.656404] ata4: SRST failed (status 0xFF)
[ 31.656459] ata4: SRST failed (err_mask=0x100)
[ 31.656514] ata4: softreset failed, retrying in 5 secs
[ 36.804622] ata4: SRST failed (status 0xFF)
[ 36.804681] ata4: SRST failed (err_mask=0x100)
[ 36.804737] ata4: softreset failed, retrying in 5 secs
[ 41.951843] ata4: SRST failed (status 0xFF)
[ 41.951898] ata4: SRST failed (err_mask=0x100)
[ 41.951952] ata4: reset failed, giving up
[ 41.952074] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHV2120B 0000 PQ: 0 ANSI: 5
[ 41.952301] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 41.956101] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 41.961208] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 41.961269] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 41.961328] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 41.961387] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 41.961446] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 41.961584] mice: PS/2 mouse device common for all mice
[ 41.961731] TCP cubic registered
[ 41.961789] NET: Registered protocol family 1
[ 41.961857] Using IPI No-Shortcut mode
[ 41.961971] ACPI: (supports<6>Time: tsc clocksource has been installed.
[ 41.962067] S0 S3 S4 S5)
[ 41.962404] Freeing unused kernel memory: 204k freed
[ 42.011608] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 42.012264] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 42.012682] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 42.012839] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 42.013518] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 42.013874] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 42.014344] ACPI: CPU1 (power states: C1[C1] C2[C2])
[ 42.014496] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 42.016427] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[ 42.017311] ACPI: Thermal Zone [TZ00] (54 C)
[ 42.018667] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[ 42.019543] ACPI: Thermal Zone [TZ01] (54 C)
[ 42.241000] Time: acpi_pm clocksource has been installed.
[ 42.381000] input: AT Translated Set 2 keyboard as /class/input/input0
[ 42.390000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 42.390000] sda: Write Protect is off
[ 42.390000] sda: Mode Sense: 00 3a 00 00
[ 42.390000] SCSI device sda: drive cache: write back
[ 42.390000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 42.390000] sda: Write Protect is off
[ 42.390000] sda: Mode Sense: 00 3a 00 00
[ 42.390000] SCSI device sda: drive cache: write back
[ 42.391000] sda: sda1 sda2 sda3
[ 42.732000] sd 2:0:0:0: Attached scsi disk sda
[ 43.057000] usbcore: registered new interface driver usbfs
[ 43.057000] usbcore: registered new interface driver hub
[ 43.058000] usbcore: registered new device driver usb
[ 43.060000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
[ 43.060000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 43.060000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 43.060000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 43.060000] ehci_hcd 0000:00:1d.7: debug port 1
[ 43.060000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 43.060000] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xdc444000
[ 43.064000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 43.064000] usb usb1: configuration #1 chosen from 1 choice
[ 43.064000] hub 1-0:1.0: USB hub found
[ 43.065000] hub 1-0:1.0: 6 ports detected
[ 43.065000] USB Universal Host Controller Interface driver v3.0
[ 43.166000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
[ 43.166000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 43.166000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 43.167000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 43.167000] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001820
[ 43.167000] usb usb2: configuration #1 chosen from 1 choice
[ 43.167000] hub 2-0:1.0: USB hub found
[ 43.167000] hub 2-0:1.0: 2 ports detected
[ 43.268000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 16
[ 43.268000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 43.268000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 43.268000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 43.268000] uhci_hcd 0000:00:1d.1: irq 16, io base 0x00001840
[ 43.268000] usb usb3: configuration #1 chosen from 1 choice
[ 43.268000] hub 3-0:1.0: USB hub found
[ 43.268000] hub 3-0:1.0: 2 ports detected
[ 43.369000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 43.369000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 43.369000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 43.369000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 43.369000] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[ 43.369000] usb usb4: configuration #1 chosen from 1 choice
[ 43.369000] hub 4-0:1.0: USB hub found
[ 43.369000] hub 4-0:1.0: 2 ports detected
[ 43.495000] ide0: I/O resource 0x1F0-0x1F7 not free.
[ 43.496000] ide0: ports already in use, skipping probe
[ 43.496000] ide1: I/O resource 0x170-0x177 not free.
[ 43.496000] ide1: ports already in use, skipping probe
[ 43.525000] Attempting manual resume
[ 43.570000] kjournald starting. Commit interval 5 seconds
[ 43.570000] EXT3-fs: mounted filesystem with ordered data mode.
[ 43.575000] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 43.739000] usb 3-1: configuration #1 chosen from 1 choice
[ 48.586000] warning: process `ls' used the removed sysctl system call
[ 48.888000] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[ 48.888000] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 49.036000] Adding 2104504k swap on /dev/sda2. Priority:-1 extents:1 across:2104504k
[ 49.101000] EXT3 FS on sda1, internal journal
[ 49.103000] warning: process `touch' used the removed sysctl system call
[ 49.166000] warning: process `touch' used the removed sysctl system call
[ 49.422000] input: PS/2 Mouse as /class/input/input1
[ 49.441000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
[ 49.462000] warning: process `evms_activate' used the removed sysctl system call
[ 49.933000] Linux agpgart interface v0.101 (c) Dave Jones
[ 49.949000] agpgart: Detected an Intel 945GM Chipset.
[ 49.950000] agpgart: Detected 7932K stolen memory.
[ 49.965000] Real Time Clock Driver v1.12ac
[ 49.968000] agpgart: AGP aperture is 256M @ 0xc0000000
[ 49.990000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 49.993000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 50.025000] input: PC Speaker as /class/input/input3
[ 50.394000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 50.409000] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 50.409000] sky2 v1.10 addr 0xd6000000 irq 17 Yukon-FE (0xb7) rev 1
[ 50.409000] sky2 eth0: addr 00:13:a9:7d:aa:6f
[ 50.482000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21
[ 50.482000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 50.536000] hda_codec: Unknown model for ALC262, trying auto-probe from BIOS...
[ 50.555000] usbcore: registered new interface driver hiddev
[ 50.580000] input: KYE Genius USB Wheel Mouse as /class/input/input4
[ 50.580000] input: USB HID v1.00 Mouse [KYE Genius USB Wheel Mouse] on usb-0000:00:1d.1-1
[ 50.580000] usbcore: registered new interface driver usbhid
[ 50.581000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 50.739000] warning: process `alsactl' used the removed sysctl system call
[ 50.872000] kjournald starting. Commit interval 5 seconds
[ 50.895000] EXT3 FS on sda3, internal journal
[ 50.895000] EXT3-fs: mounted filesystem with ordered data mode.
[ 52.290000] NET: Registered protocol family 17
[ 55.168000] ACPI: AC Adapter [ADP1] (on-line)
[ 55.223000] ACPI: Battery Slot [BAT0] (battery present)
[ 55.242000] ACPI: Lid Switch [LID0]
[ 55.242000] ACPI: Power Button (CM) [PWRB]
[ 55.287000] Using specific hotkey driver
[ 55.342000] ibm_acpi: ec object not found
[ 55.390000] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 55.400000] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 58.544000] [drm] Initialized drm 1.0.1 20051102
[ 58.560000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 58.565000] [drm] Initialized i915 1.5.0 20060119 on minor 0
[ 59.117000] sky2 eth0: enabling interface
[ 59.221000] sonypi: Sony Programmable I/O Controller Driver v1.26.
[ 59.222000] sonypi: detected type3 model, verbose = 0, fnkeyinit = off, camera = off, compat = off, mask = 0xffffffff, useinput = on, acpi = on
[ 59.222000] sonypi: enabled at irq=11, port1=0x1080, port2=0x1084
[ 59.222000] sonypi: device allocated minor is 63
[ 59.251000] input: Sony Vaio Jogdial as /class/input/input5
[ 59.251000] input: Sony Vaio Keys as /class/input/input6
[ 59.351000] sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646)
[ 59.391000] sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 657)
[ 59.431000] sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 659)
[ 59.472000] sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646)
[ 60.785000] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Slow SATA detection on bootup
2006-10-25 18:45 Slow SATA detection on bootup Stephen Hemminger
2006-10-25 19:06 ` Jeff Garzik
@ 2006-12-16 17:02 ` Jeff Garzik
1 sibling, 0 replies; 4+ messages in thread
From: Jeff Garzik @ 2006-12-16 17:02 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: linux-ide
Stephen Hemminger wrote:
> This laptop has long timeouts during bootup. Something is
> wrong. This is a Sony VAIO NG170. On a positive note suspend works.
>
> Here is the console log during the 40 seconds of dead time.
>
> [ 2.942000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
> [ 2.942000] ata1: SATA max UDMA/133 cmd 0x18B0 ctl 0x18A6 bmdma 0x1890 irq 225
> [ 2.942000] ata2: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 225
> [ 2.942000] scsi0 : ata_piix
> [ 3.094000] ata1.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32)
> [ 3.094000] ata1.00: ata1: dev 0 multi count 16
> [ 3.097000] ata1.00: configured for UDMA/100
> [ 3.097000] scsi1 : ata_piix
> [ 10.144000] ata2: port is slow to respond, please be patient
> [ 33.104000] ata2: port failed to respond (30 secs)
> [ 33.255000] ata2: SRST failed (status 0xFF)
> [ 33.255000] ata2: SRST failed (err_mask=0x100)
> [ 33.255000] ata2: softreset failed, retrying in 5 secs
> [ 38.407000] ata2: SRST failed (status 0xFF)
> [ 38.407000] ata2: SRST failed (err_mask=0x100)
> [ 38.407000] ata2: softreset failed, retrying in 5 secs
> [ 43.560000] ata2: SRST failed (status 0xFF)
> [ 43.560000] ata2: SRST failed (err_mask=0x100)
> [ 43.560000] ata2: reset failed, giving up
> [ 43.560000] Vendor: ATA Model: FUJITSU MHV2120B Rev: 0000
> [ 43.561000] Type: Direct-Access ANSI SCSI revision: 05
> [ 43.567000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
ACK or NAK -- does 2.6.20-rc1 fix this?
Jeff
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2006-12-16 17:02 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2006-10-25 18:45 Slow SATA detection on bootup Stephen Hemminger
2006-10-25 19:06 ` Jeff Garzik
2006-10-25 21:07 ` Stephen Hemminger
2006-12-16 17:02 ` Jeff Garzik
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).