* Re: nonzero mismatch_cnt with no earlier error
[not found] ` <17890.25524.465403.130119@notabene.brown>
@ 2007-02-26 8:18 ` Eyal Lebedinsky
2007-03-05 4:00 ` Tejun Heo
0 siblings, 1 reply; 6+ messages in thread
From: Eyal Lebedinsky @ 2007-02-26 8:18 UTC (permalink / raw)
To: Neil Brown; +Cc: linux-raid list, list linux-ide
I CC'ed linux-ide to see if they think the reported error was really innocent:
Question: does this error report suggest that a disk could be corrupted?
This SATA disk is part of an md raid and no error was reported by md.
[937567.332751] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4190002 action 0x2
[937567.354094] ata3.00: cmd b0/d5:01:09:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 512 in
[937567.354096] res 51/04:83:45:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[937568.120783] ata3: soft resetting port
[937568.282450] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[937568.306693] ata3.00: configured for UDMA/100
[937568.319733] ata3: EH complete
[937568.361223] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
[937568.397207] sdc: Write Protect is off
[937568.408620] sdc: Mode Sense: 00 3a 00 00
[937568.453522] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Neil Brown wrote:
> On Saturday February 24, eyal@eyal.emu.id.au wrote:
>
>>But is this not a good opportunity to repair the bad stripe for a very
>>low cost (no complete resync required)?
>
>
> In this case, 'md' knew nothing about an error. The SCSI layer
> detected something and thought it had fixed it itself. Nothing for md
> to do.
I expected this. So either the scsi layer incorrectly held back the error
report of the mismatch_cnt is due to something unrelated to the disk
i/o failure.
>>At time of error we actually know which disk failed and can re-write
>>it, something we do not know at resync time, so I assume we always
>>write to the parity disk.
Again, as I expected, resync cannot correct a problem, effectively
"blaming" the parity block. To know which block to correct one needs
a higher level parity code (can raid6 correct single bit/disk read
errors?).
> md only knows of a 'problem' if the lower level driver reports one.
> If it reports a problem for a write request, md will fail the device.
> If it reports a problem for a read request, md will try to over-write
> correct data on the failed block.
> But if the driver doesn't report the failure, there is nothing md can
> do.
>
> When performing a check/repair md looks for consistencies and fixes
> the 'arbitrarily'. For raid5/6, it just 'corrects' the parity. For
> raid1/10, it chooses one block and over-writes the other(s) with it.
>
> Mapping these corrections back to blocks in files in the filesystem is
> extremely non-trivial.
>
> NeilBrown
--
Eyal Lebedinsky (eyal@eyal.emu.id.au) <http://samba.org/eyal/>
attach .zip as .dat
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: nonzero mismatch_cnt with no earlier error
2007-02-26 8:18 ` nonzero mismatch_cnt with no earlier error Eyal Lebedinsky
@ 2007-03-05 4:00 ` Tejun Heo
2007-03-05 7:52 ` Eyal Lebedinsky
0 siblings, 1 reply; 6+ messages in thread
From: Tejun Heo @ 2007-03-05 4:00 UTC (permalink / raw)
To: Eyal Lebedinsky; +Cc: Neil Brown, linux-raid list, list linux-ide
Eyal Lebedinsky wrote:
> I CC'ed linux-ide to see if they think the reported error was really innocent:
>
> Question: does this error report suggest that a disk could be corrupted?
>
> This SATA disk is part of an md raid and no error was reported by md.
>
> [937567.332751] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4190002 action 0x2
> [937567.354094] ata3.00: cmd b0/d5:01:09:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 512 in
> [937567.354096] res 51/04:83:45:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
Command 0xb0 is SMART. The device failed some subcommand of SMART, so,
no, it isn't related to data integrity, but your link is reporting
recovered data transmission error and PHY ready status changed and some
other conditions making libata EH mark the failure as ATA bus error.
Care to post full dmesg?
--
tejun
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: nonzero mismatch_cnt with no earlier error
2007-03-05 4:00 ` Tejun Heo
@ 2007-03-05 7:52 ` Eyal Lebedinsky
2007-03-05 16:00 ` Tejun Heo
0 siblings, 1 reply; 6+ messages in thread
From: Eyal Lebedinsky @ 2007-03-05 7:52 UTC (permalink / raw)
To: Tejun Heo; +Cc: list linux-ide
Tejun Heo wrote:
> Eyal Lebedinsky wrote:
>
>>I CC'ed linux-ide to see if they think the reported error was really innocent:
>>
>>Question: does this error report suggest that a disk could be corrupted?
>>
>>This SATA disk is part of an md raid and no error was reported by md.
>>
>>[937567.332751] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4190002 action 0x2
>>[937567.354094] ata3.00: cmd b0/d5:01:09:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 512 in
>>[937567.354096] res 51/04:83:45:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
>
>
> Command 0xb0 is SMART. The device failed some subcommand of SMART, so,
> no, it isn't related to data integrity, but your link is reporting
> recovered data transmission error and PHY ready status changed and some
> other conditions making libata EH mark the failure as ATA bus error.
> Care to post full dmesg?
It is in the original thread on linux-raid, but here it is for this list.
This is the full dmesg. There were only MARKs in between.
I run a raid 'check' every Friday (cron). The last one reported some parity errors.
*** last week check start:
[927080.617744] md: data-check of RAID array md0
[927080.630783] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
[927080.648734] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[927080.678103] md: using 128k window, over a total of 312568576 blocks.
*** last week error:
[937567.332751] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4190002 action 0x2
[937567.354094] ata3.00: cmd b0/d5:01:09:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 512 in
[937567.354096] res 51/04:83:45:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[937568.120783] ata3: soft resetting port
[937568.282450] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[937568.306693] ata3.00: configured for UDMA/100
[937568.319733] ata3: EH complete
[937568.361223] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
[937568.397207] sdc: Write Protect is off
[937568.408620] sdc: Mode Sense: 00 3a 00 00
[937568.453522] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
*** last week check end:
[941696.843935] md: md0: data-check done.
[941697.246454] RAID5 conf printout:
[941697.256366] --- rd:6 wd:6
[941697.264718] disk 0, o:1, dev:sda1
[941697.275146] disk 1, o:1, dev:sdb1
[941697.285575] disk 2, o:1, dev:sdc1
[941697.296003] disk 3, o:1, dev:sdd1
[941697.306432] disk 4, o:1, dev:sde1
[941697.316862] disk 5, o:1, dev:sdf1
*** this week check start:
[1530647.746383] md: data-check of RAID array md0
[1530647.759677] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
[1530647.778041] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[1530647.807663] md: using 128k window, over a total of 312568576 blocks.
*** this week check end:
[1545248.680745] md: md0: data-check done.
[1545249.266727] RAID5 conf printout:
[1545249.276930] --- rd:6 wd:6
[1545249.285542] disk 0, o:1, dev:sda1
[1545249.296228] disk 1, o:1, dev:sdb1
[1545249.306923] disk 2, o:1, dev:sdc1
[1545249.317613] disk 3, o:1, dev:sdd1
[1545249.328292] disk 4, o:1, dev:sde1
[1545249.338981] disk 5, o:1, dev:sdf1
--
Eyal Lebedinsky (eyal@eyal.emu.id.au) <http://samba.org/eyal/>
attach .zip as .dat
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: nonzero mismatch_cnt with no earlier error
2007-03-05 7:52 ` Eyal Lebedinsky
@ 2007-03-05 16:00 ` Tejun Heo
2007-03-05 22:01 ` Eyal Lebedinsky
0 siblings, 1 reply; 6+ messages in thread
From: Tejun Heo @ 2007-03-05 16:00 UTC (permalink / raw)
To: Eyal Lebedinsky; +Cc: list linux-ide
Eyal Lebedinsky wrote:
> It is in the original thread on linux-raid, but here it is for this list.
> This is the full dmesg. There were only MARKs in between.
>
> I run a raid 'check' every Friday (cron). The last one reported some parity errors.
>
> *** last week check start:
> [927080.617744] md: data-check of RAID array md0
> [927080.630783] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
> [927080.648734] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
> [927080.678103] md: using 128k window, over a total of 312568576 blocks.
> *** last week error:
> [937567.332751] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4190002 action 0x2
> [937567.354094] ata3.00: cmd b0/d5:01:09:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 512 in
> [937567.354096] res 51/04:83:45:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
I need full kernel log including the boot messages so that I can tell
which controller/driver is involved here and also the result of 'hdparm
-I /dev/sdX' of your drives would be nice.
BTW, this is SMART read log for page 09 which is SMART self-test log.
The device aborted it. Dunno who issued it or why it got aborted. As I
wrote in the previous mail, EH discovered that SError has accumulated
link level errors and thus treated it as ATA bus error. All
transmissions over SATA are checksummed and link errors supposedly don't
cause data corruption, so, in theory, the above error message should be
irrelevant to your problem.
Ah.. please also post the result of 'smartctl -d ata -a /dev/sdX' for
your drives. That might reveal something.
--
tejun
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: nonzero mismatch_cnt with no earlier error
2007-03-05 16:00 ` Tejun Heo
@ 2007-03-05 22:01 ` Eyal Lebedinsky
2007-03-09 12:36 ` Tejun Heo
0 siblings, 1 reply; 6+ messages in thread
From: Eyal Lebedinsky @ 2007-03-05 22:01 UTC (permalink / raw)
To: Tejun Heo; +Cc: list linux-ide
[-- Attachment #1: Type: text/plain, Size: 1975 bytes --]
Tejun Heo wrote:
> Eyal Lebedinsky wrote:
>
>>It is in the original thread on linux-raid, but here it is for this list.
>>This is the full dmesg. There were only MARKs in between.
>>
>>I run a raid 'check' every Friday (cron). The last one reported some parity errors.
>>
>>*** last week check start:
>>[927080.617744] md: data-check of RAID array md0
>>[927080.630783] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
>>[927080.648734] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
>>[927080.678103] md: using 128k window, over a total of 312568576 blocks.
>> *** last week error:
>>[937567.332751] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4190002 action 0x2
>>[937567.354094] ata3.00: cmd b0/d5:01:09:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 512 in
>>[937567.354096] res 51/04:83:45:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
>
>
> I need full kernel log including the boot messages so that I can tell
> which controller/driver is involved here and also the result of 'hdparm
> -I /dev/sdX' of your drives would be nice.
>
> BTW, this is SMART read log for page 09 which is SMART self-test log.
> The device aborted it. Dunno who issued it or why it got aborted. As I
> wrote in the previous mail, EH discovered that SError has accumulated
> link level errors and thus treated it as ATA bus error. All
> transmissions over SATA are checksummed and link errors supposedly don't
> cause data corruption, so, in theory, the above error message should be
> irrelevant to your problem.
>
> Ah.. please also post the result of 'smartctl -d ata -a /dev/sdX' for
> your drives. That might reveal something.
sd[ab] are on the motherboard, sd[cdef] are on a Promise SATA-II-150-TX4.
In smartd.conf all the disks run a full selftest once a week which may have
coincided with the time of the reported error.
--
Eyal Lebedinsky (eyal@eyal.emu.id.au) <http://samba.org/eyal/>
attach .zip as .dat
[-- Attachment #2: dmesg --]
[-- Type: text/plain, Size: 47734 bytes --]
[ 0.000000] Linux version 2.6.20 (eyal@e7) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Mon Feb 5 22:08:32 EST 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000003fef0000 end: 000000003fff0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000003fff0000 size: 0000000000003000 end: 000000003fff3000 type: 4
[ 0.000000] copy_e820_map() start: 000000003fff3000 size: 000000000000d000 end: 0000000040000000 type: 3
[ 0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000001400000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
[ 0.000000] BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f5200
[ 0.000000] Entering add_active_range(0, 0, 262128) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 262128
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 262128
[ 0.000000] On node 0 totalpages: 262128
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 255 pages used for memmap
[ 0.000000] HighMem zone: 32497 pages, LIFO batch:7
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP (v000 GBT ) @ 0x000f6ca0
[ 0.000000] ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff3000
[ 0.000000] ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff3040
[ 0.000000] ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff7080
[ 0.000000] ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:2 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
[ 0.000000] Detected 3014.582 MHz processor.
[ 34.023123] Built 1 zonelists. Total pages: 260081
[ 34.023125] Kernel command line: BOOT_IMAGE=2.6.20 ro root=303 console=ttyS0,38400 console=tty0 single
[ 34.023286] mapped APIC to ffffd000 (fee00000)
[ 34.023288] mapped IOAPIC to ffffc000 (fec00000)
[ 34.023290] Enabling fast FPU save and restore... done.
[ 34.023293] Enabling unmasked SIMD FPU exception support... done.
[ 34.023300] Initializing CPU#0
[ 34.023354] CPU 0 irqstacks, hard=c03b9000 soft=c03b8000
[ 34.023356] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 34.025791] Console: colour VGA+ 80x50
[ 34.937135] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 34.958712] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 34.996037] Memory: 1035532k/1048512k available (1609k kernel code, 12344k reserved, 879k data, 268k init, 131008k highmem)
[ 35.029409] virtual kernel memory layout:
[ 35.029410] fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB)
[ 35.029411] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 35.029412] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 35.029413] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 35.029414] .init : 0xc0370000 - 0xc03b3000 ( 268 kB)
[ 35.029415] .data : 0xc0292708 - 0xc036e490 ( 879 kB)
[ 35.029416] .text : 0xc0100000 - 0xc0292708 (1609 kB)
[ 35.162043] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 35.245674] Calibrating delay using timer specific routine.. 6030.90 BogoMIPS (lpj=3015453)
[ 35.270840] Security Framework v1.0.0 initialized
[ 35.284972] Mount-cache hash table entries: 512
[ 35.298669] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[ 35.298678] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 35.314171] CPU: L2 cache: 512K
[ 35.323615] CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080 00004400 00000000 00000000
[ 35.323620] Intel machine check architecture supported.
[ 35.339314] Intel machine check reporting enabled on CPU#0.
[ 35.356045] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
[ 35.374076] CPU0: Thermal monitoring enabled
[ 35.386921] Compat vDSO mapped to ffffe000.
[ 35.399506] CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
[ 35.417142] Checking 'hlt' instruction... OK.
[ 35.433730] ACPI: Core revision 20060707
[ 35.678402] ENABLING IO-APIC IRQs
[ 35.688536] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 35.817614] NET: Registered protocol family 16
[ 35.831038] EISA bus registered
[ 35.840499] ACPI: bus type pci registered
[ 35.876470] PCI: PCI BIOS revision 2.10 entry at 0xfb500, last bus=3
[ 35.895519] PCI: Using configuration type 1
[ 35.908102] Setting up standard PCI resources
[ 35.937233] ACPI: Interpreter enabled
[ 35.948261] ACPI: Using IOAPIC for interrupt routing
[ 35.963695] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 35.978100] PCI: Probing PCI hardware (bus 00)
[ 35.978624] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[ 35.997958] PCI quirk: region 1080-10bf claimed by ICH4 GPIO
[ 36.015143] Boot video device is 0000:01:00.0
[ 36.015722] PCI: Transparent bridge - 0000:00:1e.0
[ 36.030134] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 36.037010] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 36.040728] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 36.063634] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 36.086517] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 36.109389] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 36.132268] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 36.158679] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 36.181556] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 36.204439] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 36.228698] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 36.245676] pnp: PnP ACPI init
[ 36.258805] pnp: PnP ACPI: found 16 devices
[ 36.271380] PnPBIOS: Disabled by ACPI PNP
[ 36.283478] PCI: Using ACPI for IRQ routing
[ 36.296048] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 36.349537] PCI: Bridge: 0000:00:01.0
[ 36.360543] IO window: disabled.
[ 36.370791] MEM window: d8000000-d9ffffff
[ 36.383372] PREFETCH window: c0000000-cfffffff
[ 36.397253] PCI: Bridge: 0000:00:03.0
[ 36.408276] IO window: a000-afff
[ 36.418500] MEM window: da000000-dbffffff
[ 36.431081] PREFETCH window: 50000000-500fffff
[ 36.444962] PCI: Bridge: 0000:00:1e.0
[ 36.455986] IO window: 8000-9fff
[ 36.466209] MEM window: dc000000-ddffffff
[ 36.478791] PREFETCH window: de000000-de0fffff
[ 36.492682] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 36.492703] NET: Registered protocol family 2
[ 36.514926] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 36.536458] TCP established hash table entries: 131072 (order: 7, 524288 bytes)
[ 36.558646] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 36.578662] TCP: Hash tables configured (established 131072 bind 65536)
[ 36.598487] TCP reno registered
[ 36.610925] Machine check exception polling timer started.
[ 36.627525] highmem bounce pool size: 64 pages
[ 36.640879] Total HugeTLB memory allocated, 0
[ 36.654019] VFS: Disk quotas dquot_6.5.1
[ 36.665826] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 36.685644] io scheduler noop registered
[ 36.697510] io scheduler anticipatory registered (default)
[ 36.714110] io scheduler deadline registered
[ 36.727011] io scheduler cfq registered
[ 36.738970] isapnp: Scanning for PnP cards...
[ 37.107853] isapnp: No Plug & Play device found
[ 37.139266] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 37.162877] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 37.181059] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 37.199621] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 37.216568] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 37.233598] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 37.252667] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 37.276702] ICH5: IDE controller at PCI slot 0000:00:1f.1
[ 37.292904] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
[ 37.315212] ICH5: chipset revision 2
[ 37.325971] ICH5: not 100% native mode: will probe irqs later
[ 37.343230] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
[ 37.365071] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
[ 37.386911] Probing IDE interface ide0...
[ 37.649527] hda: WDC WD2500JB-00REA0, ATA DISK drive
[ 38.275129] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 38.288839] Probing IDE interface ide1...
[ 38.958653] hdc: ATAPI DVD RW 8XMax, ATAPI CD/DVD-ROM drive
[ 39.280987] ide1 at 0x170-0x177,0x376 on irq 15
[ 39.294770] hda: max request size: 512KiB
[ 39.322149] hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
[ 39.347572] hda: cache flushes supported
[ 39.359377] hda: hda1 hda2 hda3 hda4
[ 39.389031] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 39.414497] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 39.429402] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 39.444658] mice: PS/2 mouse device common for all mice
[ 39.460436] EISA: Probing bus 0 at eisa.0
[ 39.472500] Cannot allocate resource for EISA slot 1
[ 39.487433] Cannot allocate resource for EISA slot 8
[ 39.502354] EISA: Detected 0 cards.
[ 39.542862] TCP cubic registered
[ 39.552606] Using IPI Shortcut mode
[ 39.563191] Time: tsc clocksource has been installed.
[ 39.587707] input: AT Translated Set 2 keyboard as /class/input/input0
[ 39.711228] EXT2-fs warning (device hda3): ext2_fill_super: mounting ext3 filesystem as ext2
[ 39.736713] VFS: Mounted root (ext2 filesystem) readonly.
[ 39.753089] Freeing unused kernel memory: 268k freed
[ 40.329868] NET: Registered protocol family 1
[ 41.347430] Adding 2104504k swap on /dev/hda2. Priority:1 extents:1 across:2104504k
[ 45.753592] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 46.284862] kjournald starting. Commit interval 5 seconds
[ 46.301511] EXT3 FS on hda4, internal journal
[ 46.314655] EXT3-fs: mounted filesystem with ordered data mode.
[ 47.530305] Linux agpgart interface v0.101 (c) Dave Jones
[ 47.575186] agpgart: Detected an Intel 865 Chipset.
[ 47.605367] agpgart: AGP aperture is 128M @ 0xd0000000
[ 48.224088] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 48.273692] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 49.434533] usbcore: registered new interface driver usbfs
[ 49.459572] usbcore: registered new interface driver hub
[ 49.484100] usbcore: registered new device driver usb
[ 49.522676] USB Universal Host Controller Interface driver v3.0
[ 49.549120] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 49.571423] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 49.571427] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 49.596116] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 49.618354] uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000bc00
[ 49.642587] usb usb1: configuration #1 chosen from 1 choice
[ 49.659859] hub 1-0:1.0: USB hub found
[ 49.671154] hub 1-0:1.0: 2 ports detected
[ 50.171917] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
[ 50.194228] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 50.194231] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 50.212840] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 50.235081] uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000b000
[ 50.254029] usb usb2: configuration #1 chosen from 1 choice
[ 50.271128] hub 2-0:1.0: USB hub found
[ 50.283895] hub 2-0:1.0: 2 ports detected
[ 50.462323] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
[ 50.484634] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 50.484637] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 50.534170] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 50.556413] uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000b400
[ 50.792160] usb usb3: configuration #1 chosen from 1 choice
[ 50.809942] hub 3-0:1.0: USB hub found
[ 50.821251] hub 3-0:1.0: 2 ports detected
[ 51.735367] ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 17
[ 51.757664] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 51.757668] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 51.781907] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 51.804145] uhci_hcd 0000:00:1d.3: irq 17, io base 0x0000b800
[ 51.832859] usb usb4: configuration #1 chosen from 1 choice
[ 51.850102] hub 4-0:1.0: USB hub found
[ 51.861391] hub 4-0:1.0: 2 ports detected
[ 52.886898] ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 18 (level, low) -> IRQ 16
[ 52.909203] uhci_hcd 0000:03:04.0: UHCI Host Controller
[ 52.933575] uhci_hcd 0000:03:04.0: new USB bus registered, assigned bus number 5
[ 52.955817] uhci_hcd 0000:03:04.0: irq 16, io base 0x00008c00
[ 52.984545] usb usb5: configuration #1 chosen from 1 choice
[ 53.001788] hub 5-0:1.0: USB hub found
[ 53.013090] hub 5-0:1.0: 2 ports detected
[ 53.734460] ACPI: PCI Interrupt 0000:03:04.1[B] -> GSI 21 (level, low) -> IRQ 19
[ 53.756750] uhci_hcd 0000:03:04.1: UHCI Host Controller
[ 53.776027] uhci_hcd 0000:03:04.1: new USB bus registered, assigned bus number 6
[ 53.798276] uhci_hcd 0000:03:04.1: irq 19, io base 0x00009000
[ 53.818005] usb usb6: configuration #1 chosen from 1 choice
[ 53.835960] hub 6-0:1.0: USB hub found
[ 53.847240] hub 6-0:1.0: 2 ports detected
[ 54.050380] usb 5-1: new full speed USB device using uhci_hcd and address 2
[ 54.224345] usb 5-1: configuration #1 chosen from 1 choice
[ 60.832283] dib0700: loaded with support for 2 different device-types
[ 60.868572] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in cold state, will try to load a firmware
[ 60.954450] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-01.fw'
[ 62.411983] dib0700: firmware started successfully.
[ 62.664544] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 20
[ 62.686862] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 62.686866] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 62.702928] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[ 62.725171] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[ 62.725180] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xde100000
[ 62.746049] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 62.769313] usb usb7: configuration #1 chosen from 1 choice
[ 62.786438] hub 7-0:1.0: USB hub found
[ 62.797742] hub 7-0:1.0: 8 ports detected
[ 62.910706] ACPI: PCI Interrupt 0000:03:04.2[C] -> GSI 22 (level, low) -> IRQ 21
[ 62.933002] ehci_hcd 0000:03:04.2: EHCI Host Controller
[ 62.949106] ehci_hcd 0000:03:04.2: new USB bus registered, assigned bus number 8
[ 62.971350] ehci_hcd 0000:03:04.2: irq 21, io mem 0xdd025000
[ 62.988333] ehci_hcd 0000:03:04.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 63.011576] usb usb8: configuration #1 chosen from 1 choice
[ 63.028690] hub 8-0:1.0: USB hub found
[ 63.039988] hub 8-0:1.0: 4 ports detected
[ 63.186321] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in warm state.
[ 63.207732] **WARNING** I2C adapter driver [Hauppauge Nova-T 500 Dual DVB-T] forgot to specify physical device; fix it!
[ 63.240174] dvb-usb: This USB2.0 device cannot be run on a USB1.1 port. (it lacks a hardware PID filter)
[ 63.269349] dvb-usb: Hauppauge Nova-T 500 Dual DVB-T error while loading driver (-19)
[ 63.458715] usb 8-1: new high speed USB device using ehci_hcd and address 2
[ 63.595168] usb 8-1: configuration #1 chosen from 1 choice
[ 63.614016] usb 5-1: USB disconnect, address 2
[ 63.627508] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in warm state.
[ 63.648918] **WARNING** I2C adapter driver [Hauppauge Nova-T 500 Dual DVB-T] forgot to specify physical device; fix it!
[ 63.681950] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 63.707223] DVB: registering new adapter (Hauppauge Nova-T 500 Dual DVB-T).
[ 63.793318] **WARNING** I2C adapter driver [DiBX000 tuner I2C bus] forgot to specify physical device; fix it!
[ 63.824633] DVB: registering frontend 0 (DiBcom 3000MC/P)...
[ 63.861561] MT2060: successfully identified (IF1 = 1220)
[ 64.302857] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 64.328158] DVB: registering new adapter (Hauppauge Nova-T 500 Dual DVB-T).
[ 64.351637] **WARNING** I2C adapter driver [DiBX000 tuner I2C bus] forgot to specify physical device; fix it!
[ 64.382579] DVB: registering frontend 1 (DiBcom 3000MC/P)...
[ 64.401666] MT2060: successfully identified (IF1 = 1220)
[ 64.733196] intel_rng: FWH not detected
[ 64.807042] iTCO_vendor_support: vendor-support=0
[ 64.824848] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
[ 64.846039] iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x1060)
[ 64.869166] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1)
[ 64.931292] dvb-usb: Hauppauge Nova-T 500 Dual DVB-T successfully initialized and connected.
[ 64.956680] usbcore: registered new interface driver dvb_usb_dib0700
[ 65.668661] SCSI subsystem initialized
[ 65.695351] libata version 2.00 loaded.
[ 65.752396] ata_piix 0000:00:1f.2: version 2.00ac7
[ 65.752402] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[ 65.768301] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16
[ 65.790610] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 65.790658] ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 16
[ 65.812095] ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 16
[ 65.833522] scsi0 : ata_piix
[ 65.996356] ata1.00: ATA-6, max UDMA/100, 625142448 sectors: LBA48
[ 66.015162] ata1.00: ata1: dev 0 multi count 16
[ 66.031277] ata1.00: configured for UDMA/100
[ 66.044115] scsi1 : ata_piix
[ 66.222858] ata2.00: ATA-6, max UDMA/100, 625142448 sectors: LBA48
[ 66.241666] ata2.00: ata2: dev 0 multi count 16
[ 66.257780] ata2.00: configured for UDMA/100
[ 66.270694] scsi 0:0:0:0: Direct-Access ATA WDC WD3200SD-01K 08.0 PQ: 0 ANSI: 5
[ 66.295863] scsi 1:0:0:0: Direct-Access ATA WDC WD3200JD-00K 08.0 PQ: 0 ANSI: 5
[ 67.457380] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 22
[ 68.057582] Intel 810 + AC97 Audio, version 1.01, 23:31:07 Feb 5 2007
[ 68.077602] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 22
[ 68.099940] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 68.099945] i810: Intel ICH5 found at IO 0xdc00 and 0xd800, MEM 0xde101000 and 0xde102000, IRQ 22
[ 68.126593] i810: Intel ICH5 mmio at 0xf89d2000 and 0xf89fe000
[ 68.642354] i810_audio: Primary codec has ID 2
[ 68.655743] i810_audio: Audio Controller supports 6 channels.
[ 68.672984] i810_audio: Defaulting to base 2 channel mode.
[ 68.689457] i810_audio: Resetting connection 0
[ 68.702854] i810_audio: Connection 0 with codec id 2
[ 68.718051] ac97_codec: AC97 Audio codec, id: ALG128 (Unknown)
[ 68.736201] i810_audio: AC'97 codec 2 Unable to map surround DAC's (or DAC's not present), total channels = 2
[ 69.487042] Intel(R) PRO/1000 Network Driver - version 7.3.15-k2
[ 69.505098] Copyright (c) 1999-2006 Intel Corporation.
[ 69.520930] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 16
[ 69.543269] PCI: Setting latency timer of device 0000:02:01.0 to 64
[ 69.874439] e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:0d:61:69:86:83
[ 70.119427] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 70.705027] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 70.724017] 8139cp 0000:03:00.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 70.749357] 8139cp 0000:03:00.0: Try the "8139too" driver instead.
[ 70.812131] 8139too Fast Ethernet driver 0.9.28
[ 70.826204] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16
[ 70.849433] eth1: RealTek RTL8139 at 0x8000, 00:40:f4:7c:01:da, IRQ 16
[ 70.869032] eth1: Identified 8139 chip type 'RTL-8100B/8139D'
[ 74.091716] sata_promise 0000:03:01.0: version 1.05
[ 74.091736] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 21 (level, low) -> IRQ 19
[ 74.114126] ata3: SATA max UDMA/133 cmd 0xF8CB2200 ctl 0xF8CB2238 bmdma 0x0 irq 19
[ 74.136918] ata4: SATA max UDMA/133 cmd 0xF8CB2280 ctl 0xF8CB22B8 bmdma 0x0 irq 19
[ 74.159695] ata5: SATA max UDMA/133 cmd 0xF8CB2300 ctl 0xF8CB2338 bmdma 0x0 irq 19
[ 74.182469] ata6: SATA max UDMA/133 cmd 0xF8CB2380 ctl 0xF8CB23B8 bmdma 0x0 irq 19
[ 74.205210] scsi2 : sata_promise
[ 74.499107] SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
[ 74.519243] sda: Write Protect is off
[ 74.530264] sda: Mode Sense: 00 3a 00 00
[ 74.530309] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 74.557268] SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
[ 74.577380] sda: Write Protect is off
[ 74.588400] sda: Mode Sense: 00 3a 00 00
[ 74.588425] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 74.615330] sda:<6>ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 74.801151] ata3.00: ATA-6, max UDMA/100, 625142448 sectors: LBA48
[ 74.819964] ata3.00: ata3: dev 0 multi count 0
[ 74.836071] ata3.00: configured for UDMA/100
[ 74.848944] scsi3 : sata_promise
[ 75.312714] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 75.333978] ata4.00: ATA-6, max UDMA/100, 625142448 sectors: LBA48
[ 75.352800] ata4.00: ata4: dev 0 multi count 0
[ 75.368900] ata4.00: configured for UDMA/100
[ 75.381762] scsi4 : sata_promise
[ 75.673652] sda1
[ 75.685917] sd 0:0:0:0: Attached scsi disk sda
[ 75.700714] SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
[ 75.720845] sdb: Write Protect is off
[ 75.731873] sdb: Mode Sense: 00 3a 00 00
[ 75.731917] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 75.758853] SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
[ 75.778963] sdb: Write Protect is off
[ 75.789984] sdb: Mode Sense: 00 3a 00 00
[ 75.790009] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 75.816915] sdb:<6>ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 75.996538] ata5.00: ATA-6, max UDMA/100, 625142448 sectors: LBA48
[ 76.015350] ata5.00: ata5: dev 0 multi count 0
[ 76.031445] ata5.00: configured for UDMA/100
[ 76.044330] scsi5 : sata_promise
[ 76.339534] sdb1
[ 76.348296] sd 1:0:0:0: Attached scsi disk sdb
[ 76.525053] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 76.546319] ata6.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/1)
[ 76.569069] ata6.00: ata6: dev 0 multi count 0
[ 76.585229] ata6.00: configured for UDMA/133
[ 76.598869] scsi 2:0:0:0: Direct-Access ATA WDC WD3200JD-00K 08.0 PQ: 0 ANSI: 5
[ 76.624810] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
[ 76.645279] sdc: Write Protect is off
[ 76.656316] sdc: Mode Sense: 00 3a 00 00
[ 76.657249] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 76.685185] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
[ 76.705621] sdc: Write Protect is off
[ 76.716655] sdc: Mode Sense: 00 3a 00 00
[ 76.717594] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 76.744494] sdc: sdc1
[ 76.759221] sd 2:0:0:0: Attached scsi disk sdc
[ 76.773499] scsi 3:0:0:0: Direct-Access ATA WDC WD3200JD-00K 08.0 PQ: 0 ANSI: 5
[ 76.799458] SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB)
[ 76.819883] sdd: Write Protect is off
[ 76.830916] sdd: Mode Sense: 00 3a 00 00
[ 76.831860] SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 76.859802] SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB)
[ 76.880239] sdd: Write Protect is off
[ 76.891285] sdd: Mode Sense: 00 3a 00 00
[ 76.892211] SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 76.919120] sdd: sdd1
[ 76.930419] sd 3:0:0:0: Attached scsi disk sdd
[ 76.945129] scsi 4:0:0:0: Direct-Access ATA WDC WD3200SD-01K 08.0 PQ: 0 ANSI: 5
[ 76.971059] SCSI device sde: 625142448 512-byte hdwr sectors (320073 MB)
[ 76.991500] sde: Write Protect is off
[ 77.002530] sde: Mode Sense: 00 3a 00 00
[ 77.003475] SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 77.031417] SCSI device sde: 625142448 512-byte hdwr sectors (320073 MB)
[ 77.051861] sde: Write Protect is off
[ 77.062902] sde: Mode Sense: 00 3a 00 00
[ 77.063835] SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 77.090723] sde: sde1
[ 77.107807] sd 4:0:0:0: Attached scsi disk sde
[ 77.122727] scsi 5:0:0:0: Direct-Access ATA WDC WD3200YS-01P 21.0 PQ: 0 ANSI: 5
[ 77.149653] SCSI device sdf: 625142448 512-byte hdwr sectors (320073 MB)
[ 77.170101] sdf: Write Protect is off
[ 77.181135] sdf: Mode Sense: 00 3a 00 00
[ 77.182074] SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 77.209514] SCSI device sdf: 625142448 512-byte hdwr sectors (320073 MB)
[ 77.229966] sdf: Write Protect is off
[ 77.240983] sdf: Mode Sense: 00 3a 00 00
[ 77.241939] SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 77.268846] sdf: sdf1
[ 77.281040] sd 5:0:0:0: Attached scsi disk sdf
[ 80.297720] Linux video capture interface: v2.00
[ 80.552483] bttv: driver version 0.9.16 loaded
[ 80.565851] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 80.594975] bttv: Bt8xx card found (0).
[ 80.606548] ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 22 (level, low) -> IRQ 21
[ 80.628890] bttv0: Bt878 (rev 17) at 0000:03:02.0, irq: 21, latency: 32, mmio: 0xde000000
[ 80.653631] bttv0: detected: AVermedia AverTV DVB-T 771 [card=123], PCI subsystem ID is 1461:0771
[ 80.680278] bttv0: using: AVerMedia AVerTV DVB-T 771 [card=123,autodetected]
[ 80.701453] bttv0: gpio: en=00000000, out=00000000 in=00f0ff0f [init]
[ 80.710307] bttv0: using tuner=4
[ 80.738000] bttv0: registered device video0
[ 80.761531] bttv0: registered device vbi0
[ 80.773620] bttv0: PLL: 28636363 => 35468950 .. ok
[ 80.817822] bttv0: add subdevice "dvb0"
[ 80.830446] input: bttv IR (card=123) as /class/input/input1
[ 80.847471] bttv: Bt8xx card found (1).
[ 80.859051] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 80.881365] bttv1: Bt878 (rev 17) at 0000:03:03.0, irq: 17, latency: 32, mmio: 0xde002000
[ 80.906086] bttv1: detected: AverMedia AverTV DVB-T 761 [card=124], PCI subsystem ID is 1461:0761
[ 80.932724] bttv1: using: AverMedia AverTV DVB-T 761 [card=124,autodetected]
[ 80.953898] bttv1: gpio: en=00000000, out=00000000 in=0098001d [init]
[ 80.981234] bttv1: using tuner=-1
[ 80.991709] bttv1: registered device video1
[ 81.004726] bttv1: registered device vbi1
[ 81.016845] bttv1: PLL: 28636363 => 35468950 .. ok
[ 81.062114] bttv1: add subdevice "dvb1"
[ 81.074211] input: bttv IR (card=124) as /class/input/input2
[ 81.668041] bt878: AUDIO driver version 0.0.0 loaded
[ 81.686728] bt878: Bt878 AUDIO function found (0).
[ 81.701164] ACPI: PCI Interrupt 0000:03:02.1[A] -> GSI 22 (level, low) -> IRQ 21
[ 81.725015] bt878_probe: card id=[0x7711461],[ AVermedia AverTV DVB-T 771 ] has DVB functions.
[ 81.750882] bt878(0): Bt878 (rev 17) at 03:02.1, irq: 21, latency: 32, memory: 0xde001000
[ 81.775688] bt878: Bt878 AUDIO function found (1).
[ 81.790116] ACPI: PCI Interrupt 0000:03:03.1[A] -> GSI 16 (level, low) -> IRQ 17
[ 81.812414] bt878_probe: card id=[0x7611461],[ AverMedia AverTV DVB-T 761 ] has DVB functions.
[ 81.838280] bt878(1): Bt878 (rev 17) at 03:03.1, irq: 17, latency: 32, memory: 0xde003000
[ 81.900780] btaudio: driver version 0.7 loaded [digital+analog]
[ 85.217444] ieee1394: Initialized config rom entry `ip1394'
[ 85.263009] ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 21 (level, low) -> IRQ 19
[ 85.337040] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[dd026000-dd0267ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 85.463229] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[ 85.965499] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 86.499177] gameport: NS558 PnP Gameport is pnp00:0f/gameport0, io 0x201, speed 701kHz
[ 86.606247] hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 86.628635] Uniform CD-ROM driver Revision: 3.20
[ 86.690574] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d61000069d6eb]
[ 86.816147] eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
[ 87.015794] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
[ 89.674197] md: md0 stopped.
[ 89.819759] md: bind<sdb1>
[ 89.828088] md: bind<sdc1>
[ 89.836415] md: bind<sdd1>
[ 89.844766] md: bind<sde1>
[ 89.853098] md: bind<sdf1>
[ 89.861456] md: bind<sda1>
[ 89.914296] raid5: automatically using best checksumming function: pIII_sse
[ 89.939552] pIII_sse : 3920.000 MB/sec
[ 89.952153] raid5: using function: pIII_sse (3920.000 MB/sec)
[ 89.993445] raid6: int32x1 988 MB/s
[ 90.021416] raid6: int32x2 1132 MB/s
[ 90.049369] raid6: int32x4 796 MB/s
[ 90.077326] raid6: int32x8 589 MB/s
[ 90.105191] raid6: mmxx1 2480 MB/s
[ 90.133135] raid6: mmxx2 3117 MB/s
[ 90.161079] raid6: sse1x1 1628 MB/s
[ 90.189003] raid6: sse1x2 2226 MB/s
[ 90.216958] raid6: sse2x1 2707 MB/s
[ 90.244899] raid6: sse2x2 3285 MB/s
[ 90.256198] raid6: using algorithm sse2x2 (3285 MB/s)
[ 90.271373] md: raid6 personality registered for level 6
[ 90.287328] md: raid5 personality registered for level 5
[ 90.303284] md: raid4 personality registered for level 4
[ 90.347889] raid5: device sda1 operational as raid disk 0
[ 90.364121] raid5: device sdf1 operational as raid disk 5
[ 90.380336] raid5: device sde1 operational as raid disk 4
[ 90.396548] raid5: device sdd1 operational as raid disk 3
[ 90.412761] raid5: device sdc1 operational as raid disk 2
[ 90.428974] raid5: device sdb1 operational as raid disk 1
[ 90.445627] raid5: allocated 6285kB for md0
[ 90.458220] raid5: raid level 5 set md0 active with 6 out of 6 devices, algorithm 2
[ 90.481224] RAID5 conf printout:
[ 90.490952] --- rd:6 wd:6
[ 90.499126] disk 0, o:1, dev:sda1
[ 90.509372] disk 1, o:1, dev:sdb1
[ 90.519619] disk 2, o:1, dev:sdc1
[ 90.529865] disk 3, o:1, dev:sdd1
[ 90.540112] disk 4, o:1, dev:sde1
[ 90.550361] disk 5, o:1, dev:sdf1
[ 90.649441] kjournald starting. Commit interval 5 seconds
[ 90.690035] EXT3 FS on md0, internal journal
[ 90.702982] EXT3-fs: mounted filesystem with ordered data mode.
[ 91.107326] i2c_adapter i2c-0: SMBus Quick command not supported, can't probe for chips
[ 91.131381] i2c_adapter i2c-1: SMBus Quick command not supported, can't probe for chips
[ 91.155422] i2c_adapter i2c-2: SMBus Quick command not supported, can't probe for chips
[ 91.283721] it87: Found IT8712F chip at 0x290, revision 5
[ 96.057580] Real Time Clock Driver v1.12ac
[ 96.205426] Intel 810 + AC97 Audio, version 1.01, 23:31:07 Feb 5 2007
[ 96.242132] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 96.242137] i810: Intel ICH5 found at IO 0xdc00 and 0xd800, MEM 0xde101000 and 0xde102000, IRQ 22
[ 96.268801] i810: Intel ICH5 mmio at 0xf89fe000 and 0xf8dbc000
[ 96.784549] i810_audio: Primary codec has ID 2
[ 96.797957] i810_audio: Audio Controller supports 6 channels.
[ 96.815223] i810_audio: Defaulting to base 2 channel mode.
[ 96.831697] i810_audio: Resetting connection 0
[ 96.845089] i810_audio: Connection 0 with codec id 2
[ 96.860307] ac97_codec: AC97 Audio codec, id: ALG128 (Unknown)
[ 96.878457] i810_audio: AC'97 codec 2 Unable to map surround DAC's (or DAC's not present), total channels = 2
[ 97.008529] DVB: registering new adapter (bttv0).
[ 97.050811] DVB: registering frontend 2 (Zarlink MT352 DVB-T)...
[ 97.069515] DVB: registering new adapter (bttv1).
[ 97.108013] DVB: registering frontend 3 (Spase SP887x DVB-T)...
[ 97.393021] loop: loaded (max 8 devices)
[ 97.544417] lp0: using parport0 (interrupt-driven).
[ 97.559088] lp0: console ready
[ 97.905756] input: ImPS/2 Generic Wheel Mouse as /class/input/input3
[ 1047.952036] nvidia: module license 'NVIDIA' taints kernel.
[ 1048.231688] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 1048.231877] NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9746 Fri Dec 15 09:54:45 PST 2006
[ 1112.407498] NET: Registered protocol family 17
[ 1119.475697] sp887x: waiting for firmware upload (dvb-fe-sp887x.fw)...
[ 1119.534157] i2c_adapter i2c-5: sendbytes: error - bailout.
[ 1119.553329] sp887x_initial_setup: firmware upload... sp887x: firmware upload complete
[ 1130.779962] NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9746 Fri Dec 15 09:54:45 PST 2006
[ 1130.945451] NVRM: not using NVAGP, an AGPGART backend is loaded!
[ 1131.268568] **WARNING** I2C adapter driver [NVIDIA i2c adapter 0 at 1:00.0] forgot to specify physical device; fix it!
[ 1131.301054] **WARNING** I2C adapter driver [NVIDIA i2c adapter 1 at 1:00.0] forgot to specify physical device; fix it!
[ 1131.333422] **WARNING** I2C adapter driver [NVIDIA i2c adapter 2 at 1:00.0] forgot to specify physical device; fix it!
[49609.535770] eth1: link down
[50409.031625] eth1: link down
[50458.173775] ACPI: PCI interrupt for device 0000:03:00.0 disabled
[50462.568588] 8139too Fast Ethernet driver 0.9.28
[50462.582909] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16
[50462.606650] eth1: RealTek RTL8139 at 0x8000, 00:40:f4:7c:01:da, IRQ 16
[50462.626254] eth1: Identified 8139 chip type 'RTL-8100B/8139D'
[50472.425379] eth1: link down
[50838.942315] ISO 9660 Extensions: Microsoft Joliet Level 3
[50838.995065] ISOFS: changing to secondary root
[51198.435469] Floppy drive(s): fd0 is 1.44M
[51198.462259] FDC 0 is a post-1991 82077
[51652.134564] ACPI: PCI interrupt for device 0000:03:00.0 disabled
[51654.752441] 8139too Fast Ethernet driver 0.9.28
[51654.766798] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16
[51654.790615] eth1: RealTek RTL8139 at 0x8000, 00:40:f4:7c:01:da, IRQ 16
[51654.810238] eth1: Identified 8139 chip type 'RTL-8100B/8139D'
[51732.573984] eth1: link down
[51869.230362] ACPI: PCI interrupt for device 0000:03:00.0 disabled
[51882.055418] 8139too Fast Ethernet driver 0.9.28
[51882.069632] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16
[51882.093148] eth1: RealTek RTL8139 at 0x8000, 00:40:f4:7c:01:da, IRQ 16
[51882.112753] eth1: Identified 8139 chip type 'RTL-8100B/8139D'
[51895.092156] eth1: link down
[52712.676450] ACPI: PCI interrupt for device 0000:03:00.0 disabled
[52746.611231] 8139too Fast Ethernet driver 0.9.28
[52746.625819] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16
[52746.649500] eth1: RealTek RTL8139 at 0x8000, 00:40:f4:7c:01:da, IRQ 16
[52746.669126] eth1: Identified 8139 chip type 'RTL-8100B/8139D'
[52777.548838] eth1: link up, 10Mbps, half-duplex, lpa 0x0000
[55943.661256] eth1: link down
[55952.778841] eth1: link up, 10Mbps, half-duplex, lpa 0x0000
[59314.398192] eth1: link down
[296878.789042] ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[296878.809072] ata6.00: cmd 25/00:b8:3f:c4:b6/00:00:20:00:00/e0 tag 0 cdb 0x0 data 94208 in
[296878.809074] res 50/00:00:f6:c4:b6/00:00:00:00:00/e0 Emask 0x1 (device error)
[296878.863463] ata6.00: configured for UDMA/133
[296878.876719] ata6: EH complete
[296878.887916] SCSI device sdf: 625142448 512-byte hdwr sectors (320073 MB)
[296878.908701] sdf: Write Protect is off
[296878.920049] sdf: Mode Sense: 00 3a 00 00
[296878.920677] SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[372228.827897] md: data-check of RAID array md0
[372228.841009] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[372228.858753] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[372228.888177] md: using 128k window, over a total of 312568576 blocks.
[373421.090148] md: md_do_sync() got signal ... exiting
[373900.027346] md: data-check of RAID array md0
[373900.040476] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[373900.058225] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[373900.087655] md: using 128k window, over a total of 312568576 blocks.
[373929.661179] md: md_do_sync() got signal ... exiting
[373969.047667] md: data-check of RAID array md0
[373969.060784] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[373969.078514] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[373969.107934] md: using 128k window, over a total of 312568576 blocks.
[373997.679790] md: md_do_sync() got signal ... exiting
[374111.455742] md: data-check of RAID array md0
[374111.468859] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[374111.486591] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[374111.516027] md: using 128k window, over a total of 312568576 blocks.
[374145.613884] md: md_do_sync() got signal ... exiting
[375467.714751] md: data-check of RAID array md0
[375467.727800] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[375467.745564] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[375467.774975] md: using 128k window, over a total of 312568576 blocks.
[375498.851782] md: md_do_sync() got signal ... exiting
[389928.941718] md: data-check of RAID array md0
[389928.954836] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[389928.972583] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[389929.001997] md: using 128k window, over a total of 312568576 blocks.
[390130.004529] md: md_do_sync() got signal ... exiting
[391181.917633] md: data-check of RAID array md0
[391181.930751] md: minimum _guaranteed_ speed: 10000 KB/sec/disk.
[391181.948746] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[391181.978165] md: using 128k window, over a total of 312568576 blocks.
[391205.275923] md: md_do_sync() got signal ... exiting
[391213.664075] md: data-check of RAID array md0
[391213.677230] md: minimum _guaranteed_ speed: 20000 KB/sec/disk.
[391213.695230] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[391213.724652] md: using 128k window, over a total of 312568576 blocks.
[391340.799459] md: md0: data-check done.
[391348.542935] md: data-check of RAID array md0
[391348.556051] md: minimum _guaranteed_ speed: 30000 KB/sec/disk.
[391348.574045] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[391348.603463] md: using 128k window, over a total of 312568576 blocks.
[391439.310203] md: md0: data-check done.
[391562.862444] md: data-check of RAID array md0
[391562.875572] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
[391562.893564] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[391562.922991] md: using 128k window, over a total of 312568576 blocks.
[391603.742930] md: md0: data-check done.
[411544.708182] md: data-check of RAID array md0
[411544.721215] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
[411544.739160] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[411544.768533] md: using 128k window, over a total of 312568576 blocks.
[426348.923156] md: md0: data-check done.
[426349.453805] RAID5 conf printout:
[426349.463741] --- rd:6 wd:6
[426349.472101] disk 0, o:1, dev:sda1
[426349.482528] disk 1, o:1, dev:sdb1
[426349.492958] disk 2, o:1, dev:sdc1
[426349.503386] disk 3, o:1, dev:sdd1
[426349.513819] disk 4, o:1, dev:sde1
[426349.524257] disk 5, o:1, dev:sdf1
[927080.617744] md: data-check of RAID array md0
[927080.630783] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
[927080.648734] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[927080.678103] md: using 128k window, over a total of 312568576 blocks.
[937567.332751] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4190002 action 0x2
[937567.354094] ata3.00: cmd b0/d5:01:09:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 512 in
[937567.354096] res 51/04:83:45:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[937568.120783] ata3: soft resetting port
[937568.282450] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[937568.306693] ata3.00: configured for UDMA/100
[937568.319733] ata3: EH complete
[937568.361223] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
[937568.397207] sdc: Write Protect is off
[937568.408620] sdc: Mode Sense: 00 3a 00 00
[937568.453522] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[941696.843935] md: md0: data-check done.
[941697.246454] RAID5 conf printout:
[941697.256366] --- rd:6 wd:6
[941697.264718] disk 0, o:1, dev:sda1
[941697.275146] disk 1, o:1, dev:sdb1
[941697.285575] disk 2, o:1, dev:sdc1
[941697.296003] disk 3, o:1, dev:sdd1
[941697.306432] disk 4, o:1, dev:sde1
[941697.316862] disk 5, o:1, dev:sdf1
[1530647.746383] md: data-check of RAID array md0
[1530647.759677] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
[1530647.778041] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[1530647.807663] md: using 128k window, over a total of 312568576 blocks.
[1545248.680745] md: md0: data-check done.
[1545249.266727] RAID5 conf printout:
[1545249.276930] --- rd:6 wd:6
[1545249.285542] disk 0, o:1, dev:sda1
[1545249.296228] disk 1, o:1, dev:sdb1
[1545249.306923] disk 2, o:1, dev:sdc1
[1545249.317613] disk 3, o:1, dev:sdd1
[1545249.328292] disk 4, o:1, dev:sde1
[1545249.338981] disk 5, o:1, dev:sdf1
[1561452.735032] EXT3 FS on md0, internal journal
[1565135.454597] md: requested-resync of RAID array md0
[1565135.469550] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
[1565135.487809] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for requested-resync.
[1565135.519058] md: using 128k window, over a total of 312568576 blocks.
[1571049.926138] CIFS VFS: server not responding
[1571049.939827] CIFS VFS: No response for cmd 114 mid 2686
[1579922.620488] md: md0: requested-resync done.
[1579923.081359] RAID5 conf printout:
[1579923.091529] --- rd:6 wd:6
[1579923.100144] disk 0, o:1, dev:sda1
[1579923.110833] disk 1, o:1, dev:sdb1
[1579923.121517] disk 2, o:1, dev:sdc1
[1579923.132206] disk 3, o:1, dev:sdd1
[1579923.142894] disk 4, o:1, dev:sde1
[1579923.153582] disk 5, o:1, dev:sdf1
[1587189.769116] EXT3 FS on md0, internal journal
[1601734.884903] md: data-check of RAID array md0
[1601734.898203] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
[1601734.916490] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[1601734.946174] md: using 128k window, over a total of 312568576 blocks.
[1616496.836088] md: md0: data-check done.
[1616497.290429] RAID5 conf printout:
[1616497.300607] --- rd:6 wd:6
[1616497.309218] disk 0, o:1, dev:sda1
[1616497.319909] disk 1, o:1, dev:sdb1
[1616497.330595] disk 2, o:1, dev:sdc1
[1616497.341281] disk 3, o:1, dev:sdd1
[1616497.351971] disk 4, o:1, dev:sde1
[1616497.362658] disk 5, o:1, dev:sdf1
[2134215.520301] md: data-check of RAID array md0
[2134215.533598] md: minimum _guaranteed_ speed: 24000 KB/sec/disk.
[2134215.551817] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[2134215.581438] md: using 128k window, over a total of 312568576 blocks.
[2148832.606937] md: md0: data-check done.
[2148833.104971] RAID5 conf printout:
[2148833.115150] --- rd:6 wd:6
[2148833.123777] disk 0, o:1, dev:sda1
[2148833.134474] disk 1, o:1, dev:sdb1
[2148833.145157] disk 2, o:1, dev:sdc1
[2148833.155845] disk 3, o:1, dev:sdd1
[2148833.166537] disk 4, o:1, dev:sde1
[2148833.177220] disk 5, o:1, dev:sdf1
[2277927.597019] CIFS VFS: No response for cmd 114 mid 2688
[-- Attachment #3: hdparm --]
[-- Type: text/plain, Size: 10791 bytes --]
/dev/sda:
ATA device, with non-removable media
Model Number: WDC WD3200SD-01KNB0
Serial Number: WD-WCAMR1466102
Firmware Revision: 08.05J08
Standards:
Supported: 6 5 4 3
Likely used: 6
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 625142448
device size with M = 1024*1024: 305245 MBytes
device size with M = 1000*1000: 320072 MBytes (320 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
Automatic Acoustic Management feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
/dev/sdb:
ATA device, with non-removable media
Model Number: WDC WD3200JD-00KLB0
Serial Number: WD-WMAMR1305763
Firmware Revision: 08.05J08
Standards:
Supported: 6 5 4 3
Likely used: 6
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 625142448
device size with M = 1024*1024: 305245 MBytes
device size with M = 1000*1000: 320072 MBytes (320 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
Automatic Acoustic Management feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
/dev/sdc:
ATA device, with non-removable media
Model Number: WDC WD3200JD-00KLB0
Serial Number: WD-WCAMR1427570
Firmware Revision: 08.05J08
Standards:
Supported: 6 5 4 3
Likely used: 6
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 625142448
device size with M = 1024*1024: 305245 MBytes
device size with M = 1000*1000: 320072 MBytes (320 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
Automatic Acoustic Management feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
/dev/sdd:
ATA device, with non-removable media
Model Number: WDC WD3200JD-00KLB0
Serial Number: WD-WMAMR1628424
Firmware Revision: 08.05J08
Standards:
Supported: 6 5 4 3
Likely used: 6
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 625142448
device size with M = 1024*1024: 305245 MBytes
device size with M = 1000*1000: 320072 MBytes (320 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
Automatic Acoustic Management feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
/dev/sde:
ATA device, with non-removable media
Model Number: WDC WD3200SD-01KNB0
Serial Number: WD-WCAMR1470395
Firmware Revision: 08.05J08
Standards:
Supported: 6 5 4 3
Likely used: 6
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 625142448
device size with M = 1024*1024: 305245 MBytes
device size with M = 1000*1000: 320072 MBytes (320 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
Automatic Acoustic Management feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
/dev/sdf:
ATA device, with non-removable media
Model Number: WDC WD3200YS-01PGB0
Serial Number: WD-WCAPD3621822
Firmware Revision: 21.00M21
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 625142448
device size with M = 1024*1024: 305245 MBytes
device size with M = 1000*1000: 320072 MBytes (320 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 1
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
Automatic Acoustic Management feature set
SET MAX security extension
* SET FEATURES subcommand required to spinup after power up
Power-Up In Standby feature set
* DOWNLOAD MICROCODE cmd
* General Purpose Logging feature set
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
[-- Attachment #4: smartctl --]
[-- Type: text/plain, Size: 32764 bytes --]
/dev/sda:
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3200SD-01KNB0
Serial Number: WD-WCAMR1466102
Firmware Version: 08.05J08
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Mar 6 08:37:46 2007 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (9600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 116) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 185 185 021 Pre-fail Always - 5725
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 31
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 10957
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 31
194 Temperature_Celsius 0x0022 112 096 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 10884 -
# 2 Extended offline Completed without error 00% 10717 -
# 3 Extended offline Completed without error 00% 10548 -
# 4 Extended offline Completed without error 00% 10377 -
# 5 Extended offline Completed without error 00% 10209 -
# 6 Extended offline Completed without error 00% 10041 -
# 7 Extended offline Completed without error 00% 9874 -
# 8 Extended offline Completed without error 00% 9706 -
# 9 Extended offline Completed without error 00% 9538 -
#10 Extended offline Completed without error 00% 9370 -
#11 Extended offline Completed without error 00% 9202 -
#12 Extended offline Completed without error 00% 9035 -
#13 Extended offline Completed without error 00% 8867 -
#14 Extended offline Completed without error 00% 8700 -
#15 Extended offline Completed without error 00% 8532 -
#16 Extended offline Completed without error 00% 8364 -
#17 Extended offline Completed without error 00% 8196 -
#18 Extended offline Completed without error 00% 8028 -
#19 Extended offline Completed without error 00% 7861 -
#20 Extended offline Completed without error 00% 241 -
#21 Short offline Completed without error 00% 239 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
/dev/sdb:
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3200JD-00KLB0
Serial Number: WD-WMAMR1305763
Firmware Version: 08.05J08
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Mar 6 08:37:46 2007 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (9600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 116) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 186 185 021 Pre-fail Always - 5700
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 100
5 Reallocated_Sector_Ct 0x0033 195 195 140 Pre-fail Always - 35
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 12292
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 100
194 Temperature_Celsius 0x0022 110 089 000 Old_age Always - 40
196 Reallocated_Event_Count 0x0032 198 198 000 Old_age Always - 2
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 12220 -
# 2 Extended offline Completed without error 00% 12052 -
# 3 Extended offline Completed without error 00% 11884 -
# 4 Extended offline Completed without error 00% 11712 -
# 5 Extended offline Completed without error 00% 11545 -
# 6 Extended offline Completed without error 00% 11377 -
# 7 Extended offline Completed without error 00% 11209 -
# 8 Extended offline Completed without error 00% 11041 -
# 9 Extended offline Completed without error 00% 10874 -
#10 Extended offline Completed without error 00% 10706 -
#11 Extended offline Completed without error 00% 10538 -
#12 Extended offline Completed without error 00% 10371 -
#13 Extended offline Completed without error 00% 10203 -
#14 Extended offline Completed without error 00% 10035 -
#15 Extended offline Completed without error 00% 9867 -
#16 Extended offline Completed without error 00% 9699 -
#17 Extended offline Completed without error 00% 9531 -
#18 Extended offline Completed without error 00% 9364 -
#19 Extended offline Completed without error 00% 9196 -
#20 Extended offline Completed without error 00% 1576 -
#21 Conveyance offline Interrupted (host reset) 40% 1014 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
/dev/sdc:
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3200JD-00KLB0
Serial Number: WD-WCAMR1427570
Firmware Version: 08.05J08
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Mar 6 08:37:47 2007 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (9600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 116) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 195 186 021 Pre-fail Always - 5225
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 52
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 11180
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 52
194 Temperature_Celsius 0x0022 110 095 000 Old_age Always - 40
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 665
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 11107 -
# 2 Extended offline Completed without error 00% 10939 -
# 3 Extended offline Completed without error 00% 10600 -
# 4 Extended offline Completed without error 00% 10432 -
# 5 Extended offline Completed without error 00% 10264 -
# 6 Extended offline Completed without error 00% 10096 -
# 7 Extended offline Completed without error 00% 9929 -
# 8 Extended offline Completed without error 00% 9761 -
# 9 Extended offline Completed without error 00% 9593 -
#10 Extended offline Completed without error 00% 9425 -
#11 Extended offline Completed without error 00% 9258 -
#12 Extended offline Completed without error 00% 9090 -
#13 Extended offline Completed without error 00% 8922 -
#14 Extended offline Completed without error 00% 8755 -
#15 Extended offline Completed without error 00% 8587 -
#16 Extended offline Completed without error 00% 8419 -
#17 Extended offline Completed without error 00% 8251 -
#18 Conveyance offline Completed without error 00% 8098 -
#19 Extended offline Completed without error 00% 8084 -
#20 Extended offline Completed without error 00% 463 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
/dev/sdd:
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3200JD-00KLB0
Serial Number: WD-WMAMR1628424
Firmware Version: 08.05J08
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Mar 6 08:37:47 2007 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (9600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 116) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 191 190 021 Pre-fail Always - 5450
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 85
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 11915
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 85
194 Temperature_Celsius 0x0022 109 095 000 Old_age Always - 41
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 283
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 11842 -
# 2 Extended offline Completed without error 00% 11674 -
# 3 Extended offline Completed without error 00% 11506 -
# 4 Extended offline Completed without error 00% 11335 -
# 5 Extended offline Completed without error 00% 11167 -
# 6 Extended offline Completed without error 00% 10999 -
# 7 Extended offline Completed without error 00% 10831 -
# 8 Extended offline Completed without error 00% 10664 -
# 9 Extended offline Completed without error 00% 10495 -
#10 Extended offline Completed without error 00% 10328 -
#11 Extended offline Completed without error 00% 10160 -
#12 Extended offline Completed without error 00% 9993 -
#13 Extended offline Completed without error 00% 9825 -
#14 Extended offline Completed without error 00% 9657 -
#15 Extended offline Completed without error 00% 9490 -
#16 Extended offline Completed without error 00% 9322 -
#17 Extended offline Completed without error 00% 9154 -
#18 Extended offline Completed without error 00% 8986 -
#19 Conveyance offline Completed without error 00% 8833 -
#20 Extended offline Completed without error 00% 8819 -
#21 Extended offline Completed without error 00% 1198 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
/dev/sde:
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3200SD-01KNB0
Serial Number: WD-WCAMR1470395
Firmware Version: 08.05J08
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Mar 6 08:37:47 2007 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (9600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 116) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 188 188 021 Pre-fail Always - 5558
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 38
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 086 086 000 Old_age Always - 10269
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 38
194 Temperature_Celsius 0x0022 111 090 000 Old_age Always - 39
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 10196 -
# 2 Extended offline Completed without error 00% 10028 -
# 3 Extended offline Completed without error 00% 9861 -
# 4 Extended offline Completed without error 00% 9689 -
# 5 Extended offline Completed without error 00% 9521 -
# 6 Extended offline Completed without error 00% 9353 -
# 7 Extended offline Completed without error 00% 9186 -
# 8 Extended offline Completed without error 00% 9018 -
# 9 Extended offline Completed without error 00% 8850 -
#10 Extended offline Completed without error 00% 8682 -
#11 Extended offline Completed without error 00% 8514 -
#12 Extended offline Completed without error 00% 8347 -
#13 Extended offline Completed without error 00% 8179 -
#14 Extended offline Completed without error 00% 8011 -
#15 Extended offline Completed without error 00% 7844 -
#16 Extended offline Completed without error 00% 7676 -
#17 Extended offline Completed without error 00% 7508 -
#18 Extended offline Completed without error 00% 7340 -
#19 Extended offline Completed without error 00% 7173 -
#20 Extended offline Completed without error 00% 241 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
/dev/sdf:
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3200YS-01PGB0
Serial Number: WD-WCAPD3621822
Firmware Version: 21.00M21
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Mar 6 08:37:47 2007 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (9600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 111) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 100 253 021 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 4
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 712
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3
190 Unknown_Attribute 0x0022 062 044 000 Old_age Always - 38
194 Temperature_Celsius 0x0022 112 095 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 640 -
# 2 Extended offline Completed without error 00% 472 -
# 3 Extended offline Completed without error 00% 304 -
# 4 Extended offline Completed without error 00% 133 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: nonzero mismatch_cnt with no earlier error
2007-03-05 22:01 ` Eyal Lebedinsky
@ 2007-03-09 12:36 ` Tejun Heo
0 siblings, 0 replies; 6+ messages in thread
From: Tejun Heo @ 2007-03-09 12:36 UTC (permalink / raw)
To: Eyal Lebedinsky; +Cc: list linux-ide
Hello, sorry about the long delay.
Eyal Lebedinsky wrote:
>> BTW, this is SMART read log for page 09 which is SMART self-test log.
>> The device aborted it. Dunno who issued it or why it got aborted. As I
>> wrote in the previous mail, EH discovered that SError has accumulated
>> link level errors and thus treated it as ATA bus error. All
>> transmissions over SATA are checksummed and link errors supposedly don't
>> cause data corruption, so, in theory, the above error message should be
>> irrelevant to your problem.
>>
>> Ah.. please also post the result of 'smartctl -d ata -a /dev/sdX' for
>> your drives. That might reveal something.
>
> sd[ab] are on the motherboard, sd[cdef] are on a Promise SATA-II-150-TX4.
>
> In smartd.conf all the disks run a full selftest once a week which may have
> coincided with the time of the reported error.
All the logs look fine. No driver recorded any error condition in smart
logs. The SMART command abort is really fishy. There is no reason the
device would abort that command unless something weird is going on. I'm
afraid I can't tell much at this point. It might be a good idea to
schedule SMART self test and RAID checksumming at different time slot.
--
tejun
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2007-03-09 12:36 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <45DF859B.2050108@eyal.emu.id.au>
[not found] ` <Pine.LNX.4.64.0702231929380.31611@p34.internal.lan>
[not found] ` <45DF8DE3.2050903@eyal.emu.id.au>
[not found] ` <17890.25524.465403.130119@notabene.brown>
2007-02-26 8:18 ` nonzero mismatch_cnt with no earlier error Eyal Lebedinsky
2007-03-05 4:00 ` Tejun Heo
2007-03-05 7:52 ` Eyal Lebedinsky
2007-03-05 16:00 ` Tejun Heo
2007-03-05 22:01 ` Eyal Lebedinsky
2007-03-09 12:36 ` Tejun Heo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).