From: Stephen Clark <Stephen.Clark@seclark.us>
To: linux-ide@vger.kernel.org
Subject: CD problems booting FC7 RC3
Date: Mon, 02 Apr 2007 15:58:19 -0400 [thread overview]
Message-ID: <4611605B.6060601@seclark.us> (raw)
Hi,
When trying to boot FC7 RC3 on my HP N5430 laptop I get the following:
...
Write protecting the kernel read-only data: 845k
input: PS/2 Generic Mouse as /class/input/input2
SCSI subsystem initialized
libata version 2.20 loaded.
ACPI: Unable to derive IRQ for device 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[A]: no GSI
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011000
irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011008
irq 15
scsi0 : pata_ali
PM: Adding info for No Bus:host0
ata1.00: ATA-5: HITACHI_DK23CA-20, 00H1A0A3, max UDMA/100
ata1.00: 39070080 sectors, multi 16: LBA
ata1.00: configured for UDMA/33
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
powernow: SGTC: 10000
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
powernow: SGTC: 10000
powernow: Minimum speed 300 MHz. Maximum speed 850 MHz.
powernow-k8: Processor cpuid 670 not supported
Using IPI No-Shortcut mode
Magic number: 3:342:541
Freeing unused kernel memory: 248k freed
Write protecting the kernel read-only data: 845k
input: PS/2 Generic Mouse as /class/input/input2
SCSI subsystem initialized
libata version 2.20 loaded.
ACPI: Unable to derive IRQ for device 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[A]: no GSI
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011000
irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011008
irq 15
scsi0 : pata_ali
PM: Adding info for No Bus:host0
ata1.00: ATA-5: HITACHI_DK23CA-20, 00H1A0A3, max UDMA/100
ata1.00: 39070080 sectors, multi 16: LBA
ata1.00: configured for UDMA/33
scsi1 : pata_ali
PM: Adding info for No Bus:host1
ata2.00: ATAPI, max UDMA/33
ata2.00: configured for UDMA/33
PM: Adding info for No Bus:target0:0:0
scsi 0:0:0:0: Direct-Access ATA HITACHI_DK23CA-2 00H1 PQ: 0 ANSI: 5
PM: Adding info for scsi:0:0:0:0
PM: Adding info for No Bus:target1:0:0
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x12 data 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata2: soft resetting port
ATA: abnormal status 0xD0 on port 0x00010177
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x2)
ata2.00: revalidation failed (errno=-5)
ata2: failed to recover some devices, retrying in 5 secs
ata2: port is slow to respond, please be patient (Status 0xd0)
ata2: port failed to respond (30 secs, Status 0xd0)
ata2: soft resetting port
ATA: abnormal status 0xD0 on port 0x00010177
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x2)
ata2.00: revalidation failed (errno=-5)
ata2.00: limiting speed to UDMA/33:PIO3
ata2: failed to recover some devices, retrying in 5 secs
ata2: port is slow to respond, please be patient (Status 0xd0)
ata2: port failed to respond (30 secs, Status 0xd0)
ata2: soft resetting port
ATA: abnormal status 0xD0 on port 0x00010177
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x2)
ata2.00: revalidation failed (errno=-5)
ata2.00: disabled
ata2: EH complete
PM: Removing info for No Bus:target1:0:0
SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO
or FUA
SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO
or FUA
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
--------------------------------------
WARNING: Cannot find root file system!
--------------------------------------
Create symlink /dev/root and then exit this shell to continue
the boot sequence.
bash: no job control in this shell
bash-3.2#
(END)
--
"They that give up essential liberty to obtain temporary safety,
deserve neither liberty nor safety." (Ben Franklin)
"The course of history shows that as a government grows, liberty
decreases." (Thomas Jefferson)
next reply other threads:[~2007-04-02 19:58 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-04-02 19:58 Stephen Clark [this message]
2007-04-03 2:40 ` CD problems booting FC7 RC3 Albert Lee
2007-04-03 13:37 ` Stephen Clark
-- strict thread matches above, loose matches on Subject: below --
2007-04-07 2:55 Vlad Codrea
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4611605B.6060601@seclark.us \
--to=stephen.clark@seclark.us \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).