From: "Lars Michael Jogbäck" <lm@jogback.se>
To: Tejun Heo <htejun@gmail.com>
Cc: linux-ide@vger.kernel.org
Subject: Re: Problems w/ Sil3124 + Port Multiplier
Date: Thu, 03 May 2007 13:04:59 +0200 [thread overview]
Message-ID: <4639C1DB.3030501@jogback.se> (raw)
In-Reply-To: <4639A6A3.20001@gmail.com>
Tejun Heo wrote:
> Lars Michael Jogbäck wrote:
>
>>> I think the disk attached to port 0 might be bad. Please report the
>>> result of 'smartctl -d ata -a /dev/sdX' where sdX is the device attached
>>> to the failing port.
>>>
>>>
>>>
>> SMART Error Log Version: 1
>> No Errors Logged
>>
>
> I was hoping to see some error logs but no. Hardware_ECC_Recovered
> count seems high (385707184) but I dunno whether the value is normal or
> not. Different manufacturers use different norms in counting them. If
> you have other disks of the same model, you can compare the values and
> see whether if it's unusually high.
>
I think that is normal for that kind of disk. This is another disk but
the same model (this one is attached to a 3ware 9500-controller)
and it shows the same.
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD501LJ
Serial Number: S0VVJ1NP300014
Firmware Version: CR100-10
User Capacity: 500,107,862,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Not recognized. Minor revision code: 0x52
Local Time is: Thu May 3 12:36:32 2007 CEST
==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for
details.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: (8852) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 151) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail
Always - 3
3 Spin_Up_Time 0x0007 100 100 015 Pre-fail
Always - 7104
4 Start_Stop_Count 0x0032 100 100 000 Old_age
Always - 7
5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0025 253 253 015 Pre-fail
Offline - 0
9 Power_On_Hours 0x0032 253 253 000 Old_age
Always - 97
10 Spin_Retry_Count 0x0033 253 253 051 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x0012 253 253 000 Old_age
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 7
187 Unknown_Attribute 0x0032 253 253 000 Old_age
Always - 0
188 Unknown_Attribute 0x0032 253 253 000 Old_age
Always - 0
190 Unknown_Attribute 0x0022 068 067 000 Old_age
Always - 32
194 Temperature_Celsius 0x0022 142 139 000 Old_age
Always - 32
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age
Always - 455228167
196 Reallocated_Event_Count 0x0032 253 253 000 Old_age
Always - 0
197 Current_Pending_Sector 0x0012 253 253 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0030 253 253 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age
Always - 0
201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age
Always - 0
202 TA_Increase_Count 0x0032 253 253 000 Old_age
Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00%
97 -
SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data
structure revision number = 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Also, something else happened with error after a while.
First it changed to show this instead:
May 1 23:52:25 cleopatra kernel: ata5.00: limiting SATA link speed to
1.5 Gbps
May 1 23:52:25 cleopatra kernel: ata5.00: exception Emask 0x0 SAct 0x0
SErr 0x0 action 0x6 frozen
May 1 23:52:25 cleopatra kernel: ata5.00: tag 2 cmd 0xea Emask 0x4 stat
0x40 err 0x0 (timeout)
May 1 23:52:25 cleopatra kernel: ata5.15: hard resetting port
May 1 23:52:27 cleopatra kernel: ata5.15: SATA link up 3.0 Gbps
(SStatus 123 SControl 300)
May 1 23:52:27 cleopatra kernel: ata5.00: hard resetting port
May 1 23:52:28 cleopatra kernel: ata5.00: SATA link up 1.5 Gbps
(SStatus 113 SControl 310)
May 1 23:52:28 cleopatra kernel: ata5.01: hard resetting port
May 1 23:52:28 cleopatra kernel: ata5.01: SATA link up 3.0 Gbps
(SStatus 123 SControl 300)
May 1 23:52:29 cleopatra kernel: ata5.02: hard resetting port
May 1 23:52:29 cleopatra kernel: ata5.02: SATA link up 1.5 Gbps
(SStatus 113 SControl 300)
May 1 23:52:29 cleopatra kernel: ata5.03: hard resetting port
May 1 23:52:30 cleopatra kernel: ata5.03: SATA link up 1.5 Gbps
(SStatus 113 SControl 300)
May 1 23:52:30 cleopatra kernel: ata5.04: hard resetting port
May 1 23:52:30 cleopatra kernel: ata5.04: SATA link up 1.5 Gbps
(SStatus 113 SControl 300)
May 1 23:52:30 cleopatra kernel: ata5.00: configured for UDMA/100
May 1 23:52:30 cleopatra kernel: ata5.01: configured for UDMA/100
May 1 23:52:30 cleopatra kernel: ata5.02: configured for UDMA/100
May 1 23:52:30 cleopatra kernel: ata5.03: configured for UDMA/100
May 1 23:52:30 cleopatra kernel: ata5.04: configured for UDMA/100
May 1 23:52:30 cleopatra kernel: ata5: EH complete
and later it showed this:
May 1 23:53:36 cleopatra kernel: ata5.00: limiting speed to UDMA/66
May 1 23:53:36 cleopatra kernel: ata5.00: exception Emask 0x0 SAct 0x0
SErr 0x0 action 0x2 frozen
May 1 23:53:36 cleopatra kernel: ata5.00: tag 0 cmd 0xea Emask 0x4 stat
0x40 err 0x0 (timeout)
May 1 23:53:36 cleopatra kernel: ata5.15: hard resetting port
May 1 23:53:38 cleopatra kernel: ata5.15: SATA link up 3.0 Gbps
(SStatus 123 SControl 300)
May 1 23:53:38 cleopatra kernel: ata5.00: hard resetting port
May 1 23:53:39 cleopatra kernel: ata5.00: SATA link up 1.5 Gbps
(SStatus 113 SControl 310)
May 1 23:53:39 cleopatra kernel: ata5.01: hard resetting port
May 1 23:53:40 cleopatra kernel: ata5.01: SATA link up 3.0 Gbps
(SStatus 123 SControl 300)
May 1 23:53:40 cleopatra kernel: ata5.02: hard resetting port
May 1 23:53:40 cleopatra kernel: ata5.02: SATA link up 1.5 Gbps
(SStatus 113 SControl 300)
May 1 23:53:40 cleopatra kernel: ata5.03: hard resetting port
May 1 23:53:41 cleopatra kernel: ata5.03: SATA link up 1.5 Gbps
(SStatus 113 SControl 300)
May 1 23:53:41 cleopatra kernel: ata5.04: hard resetting port
May 1 23:53:41 cleopatra kernel: ata5.04: SATA link up 1.5 Gbps
(SStatus 113 SControl 300)
May 1 23:53:41 cleopatra kernel: ata5.00: configured for UDMA/66
May 1 23:53:41 cleopatra kernel: ata5.01: configured for UDMA/100
May 1 23:53:41 cleopatra kernel: ata5.02: configured for UDMA/100
May 1 23:53:41 cleopatra kernel: ata5.03: configured for UDMA/100
May 1 23:53:41 cleopatra kernel: ata5.04: configured for UDMA/100
May 1 23:53:41 cleopatra kernel: ata5: EH complete
and then it continues with approx 1/hour of the above. So it seems
something is strange in the interface between the drive and the
computer. I can swap the drive (it's in an raid5-array) to another drive
of the same model if helps in any way; but I suspect that it will show
the same result.
Regards,
/LM
next prev parent reply other threads:[~2007-05-03 11:04 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-05-02 6:00 Problems w/ Sil3124 + Port Multiplier Lars Michael Jogbäck
2007-05-02 12:47 ` Tejun Heo
2007-05-02 13:30 ` Lars Michael Jogbäck
2007-05-02 13:34 ` Mark Lord
2007-05-03 9:08 ` Tejun Heo
2007-05-03 11:04 ` Lars Michael Jogbäck [this message]
2007-05-03 11:37 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4639C1DB.3030501@jogback.se \
--to=lm@jogback.se \
--cc=htejun@gmail.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).