* sata_via, 2.6.22-rc1, VT6421A
@ 2007-05-17 10:09 Tim Valenzuela
2007-05-17 11:37 ` [PATCH] sata_via: pcim_iomap_regions() conversion missed BAR5 Tejun Heo
0 siblings, 1 reply; 6+ messages in thread
From: Tim Valenzuela @ 2007-05-17 10:09 UTC (permalink / raw)
To: ", linux-ide
[-- Attachment #1: Type: text/plain, Size: 797 bytes --]
Recently, I acquired a
"SYBA SY-VIA-150 PCI SATA / IDE Combo Controller Card, Non Raid"
The physical chip reads "VT6421A 0651CD TAIWAN 21A0028971".
Each SATA channel has a drive plugged in, the PATA does not.
When using 2.6.22-rc1 I get some IO errors:
[ 32.177782] Bad IO access at port 8 (return inl(port))
[ 32.177866] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.177950] [<c02b7801>] ioread32+0x21/0x30
[ 32.178078] [<c038839c>] sata_scr_read+0x2c/0x50
Neither drive shows up in /dev.
When using earlier kernels (2.6.20, 2.6.21) the first SATA channel
seems to work, however the second channel has some IO errors:
"failed to IDENTIFY (I/O error, err_mask=0x1)"
Attached is a complete dmesg log of the 2.6.22-rc1 kernel and a partial
log from a 2.6.21.1 boot.
- Tim Valenzuela
[-- Attachment #2: dmesg_complete-2.6.22-rc1.txt --]
[-- Type: text/plain, Size: 46187 bytes --]
[ 0.000000] Linux version 2.6.22-rc1 (root@centauri) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #2 PREEMPT Thu May 17 02:25:09 MST 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[ 0.000000] BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 131056) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 131056
[ 0.000000] HighMem 131056 -> 131056
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 131056
[ 0.000000] On node 0 totalpages: 131056
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 991 pages used for memmap
[ 0.000000] Normal zone: 125969 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP 000F75E0, 0014 (r0 Nvidia)
[ 0.000000] ACPI: RSDT 1FFF3000, 002C (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP 1FFF3040, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT 1FFF30C0, 4561 (r1 NVIDIA AWRDACPI 1000 MSFT 100000E)
[ 0.000000] ACPI: FACS 1FFF0000, 0040
[ 0.000000] ACPI: APIC 1FFF7640, 006E (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:8 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[ 0.000000] Built 1 zonelists. Total pages: 130033
[ 0.000000] Kernel command line: root=/dev/hda2
[ 0.000000] Found and enabled local APIC!
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1997.061 MHz processor.
[ 28.065144] Console: colour VGA+ 80x25
[ 28.068445] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 28.068799] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 28.082176] Memory: 511996k/524224k available (3627k kernel code, 11672k reserved, 1072k data, 208k init, 0k highmem)
[ 28.082313] virtual kernel memory layout:
[ 28.082314] fixmap : 0xfffea000 - 0xfffff000 ( 84 kB)
[ 28.082315] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 28.082317] vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
[ 28.082318] lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
[ 28.082319] .init : 0xc059a000 - 0xc05ce000 ( 208 kB)
[ 28.082321] .data : 0xc048afc8 - 0xc059738c (1072 kB)
[ 28.082322] .text : 0xc0100000 - 0xc048afc8 (3627 kB)
[ 28.082986] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 28.163118] Calibrating delay using timer specific routine.. 3996.99 BogoMIPS (lpj=7993994)
[ 28.163319] Mount-cache hash table entries: 512
[ 28.163517] CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
[ 28.163525] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 28.163616] CPU: L2 Cache: 256K (64 bytes/line)
[ 28.163698] CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000
[ 28.163704] Intel machine check architecture supported.
[ 28.163788] Intel machine check reporting enabled on CPU#0.
[ 28.163877] Compat vDSO mapped to ffffe000.
[ 28.163966] CPU: AMD Athlon(tm) XP 2400+ stepping 01
[ 28.164130] Checking 'hlt' instruction... OK.
[ 28.179280] ACPI: Core revision 20070126
[ 28.181411] ACPI: setting ELCR to 0200 (from 1a20)
[ 28.287109] NET: Registered protocol family 16
[ 28.287300] ACPI: bus type pci registered
[ 28.319530] PCI: PCI BIOS revision 2.10 entry at 0xfb410, last bus=3
[ 28.319619] PCI: Using configuration type 1
[ 28.319699] Setting up standard PCI resources
[ 28.328961] ACPI: Interpreter enabled
[ 28.329047] ACPI: (supports S0 S1 S4 S5)
[ 28.329341] ACPI: Using PIC for interrupt routing
[ 28.338242] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 28.338341] PCI: Probing PCI hardware (bus 00)
[ 28.338422] PCI: nForce2 C1 Halt Disconnect fixup
[ 28.339468] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 28.339678] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 28.339947] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[ 28.390051] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 28.390930] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 28.391707] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 28.392486] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[ 28.393262] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 28.394120] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[ 28.394905] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 28.395683] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 28.396461] ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[ 28.397394] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 28.398169] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 28.399035] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 28.399816] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 28.400597] ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 28.401374] ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 28.402234] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 28.403081] ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
[ 28.403440] ACPI: PCI Interrupt Link [APC2] (IRQs *17)
[ 28.403756] ACPI: PCI Interrupt Link [APC3] (IRQs *18)
[ 28.404070] ACPI: PCI Interrupt Link [APC4] (IRQs *19)
[ 28.404383] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[ 28.404794] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0
[ 28.405281] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0
[ 28.405767] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0
[ 28.406253] ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0
[ 28.406740] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0
[ 28.407229] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
[ 28.407710] ACPI: PCI Interrupt Link [APCS] (IRQs *23)
[ 28.408074] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0
[ 28.408559] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0
[ 28.409045] ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
[ 28.409574] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
[ 28.410051] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 28.410148] pnp: PnP ACPI init
[ 28.410234] ACPI: bus type pnp registered
[ 28.415128] pnp: PnP ACPI: found 16 devices
[ 28.415212] ACPI: ACPI bus type pnp unregistered
[ 28.415405] SCSI subsystem initialized
[ 28.415511] libata version 2.20 loaded.
[ 28.415579] usbcore: registered new interface driver usbfs
[ 28.415695] usbcore: registered new interface driver hub
[ 28.415814] usbcore: registered new device driver usb
[ 28.415936] PCI: Using ACPI for IRQ routing
[ 28.416021] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 28.473768] pnp: 00:00: ioport range 0x4000-0x407f has been reserved
[ 28.473858] pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
[ 28.473946] pnp: 00:00: ioport range 0x4400-0x447f has been reserved
[ 28.474034] pnp: 00:00: ioport range 0x4480-0x44ff has been reserved
[ 28.474122] pnp: 00:00: ioport range 0x4200-0x427f has been reserved
[ 28.474210] pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
[ 28.474304] pnp: 00:01: ioport range 0x5000-0x503f has been reserved
[ 28.474392] pnp: 00:01: ioport range 0x5500-0x553f has been reserved
[ 28.474485] pnp: 00:02: iomem range 0xf0000-0xf3fff could not be reserved
[ 28.474574] pnp: 00:02: iomem range 0xf4000-0xf7fff could not be reserved
[ 28.474664] pnp: 00:02: iomem range 0xf8000-0xfbfff could not be reserved
[ 28.474754] Time: tsc clocksource has been installed.
[ 28.474840] pnp: 00:02: iomem range 0xfc000-0xfffff could not be reserved
[ 28.475570] ACPI: PCI Interrupt Link [LFIR] enabled at IRQ 9
[ 28.475659] PCI: setting IRQ 9 as level-triggered
[ 28.475662] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LFIR] -> GSI 9 (level, low) -> IRQ 9
[ 28.475867] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 28.527715] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[9] MMIO=[e8086000-e80867ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 28.562868] PCI: Bridge: 0000:00:08.0
[ 28.562948] IO window: 9000-bfff
[ 28.563028] MEM window: e4000000-e6ffffff
[ 28.563110] PREFETCH window: 30000000-300fffff
[ 28.563194] PCI: Bridge: 0000:00:1e.0
[ 28.563271] IO window: disabled.
[ 28.563350] MEM window: disabled.
[ 28.563429] PREFETCH window: disabled.
[ 28.563518] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 28.563558] NET: Registered protocol family 2
[ 28.598533] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 28.598696] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 28.599008] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 28.599197] TCP: Hash tables configured (established 16384 bind 16384)
[ 28.599286] TCP reno registered
[ 28.610733] Machine check exception polling timer started.
[ 28.610959] audit: initializing netlink socket (disabled)
[ 28.611053] audit(1179368785.420:1): initialized
[ 28.611322] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 28.611626] NTFS driver 2.1.28 [Flags: R/W].
[ 28.611728] fuse init (API version 7.8)
[ 28.611907] io scheduler noop registered
[ 28.611988] io scheduler anticipatory registered (default)
[ 28.612073] io scheduler deadline registered
[ 28.612166] io scheduler cfq registered
[ 28.666422] Boot video device is 0000:01:0a.0
[ 28.666744] input: Power Button (FF) as /class/input/input0
[ 28.666831] ACPI: Power Button (FF) [PWRF]
[ 28.666971] input: Power Button (CM) as /class/input/input1
[ 28.667057] ACPI: Power Button (CM) [PWRB]
[ 28.694108] lp: driver loaded but no devices found
[ 28.694262] Real Time Clock Driver v1.12ac
[ 28.694342] Linux agpgart interface v0.102 (c) Dave Jones
[ 28.694515] agpgart: Detected NVIDIA nForce2 chipset
[ 28.699238] agpgart: AGP aperture is 64M @ 0xe0000000
[ 28.699353] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 28.700388] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 28.702876] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 28.703561] parport_pc 00:0c: reported by Plug and Play ACPI
[ 28.703672] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
[ 28.704050] lp0: using parport0 (interrupt-driven).
[ 28.722014] FDC 0 is a post-1991 82077
[ 28.723503] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
[ 28.723622] loop: module loaded
[ 28.723753] sk98lin: driver has been replaced by the skge driver and is scheduled for removal
[ 28.724233] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 5
[ 28.724320] PCI: setting IRQ 5 as level-triggered
[ 28.724324] ACPI: PCI Interrupt 0000:01:04.0[A] -> Link [LNK2] -> GSI 5 (level, low) -> IRQ 5
[ 28.811747] eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
[ 28.811836] PrefPort:A RlmtMode:Check Link State
[ 28.812011] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 28.812419] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 5
[ 28.812506] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LMAC] -> GSI 5 (level, low) -> IRQ 5
[ 28.812710] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 29.329671] eth1: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0
[ 29.329777] Linux video capture interface: v2.00
[ 29.329876] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 29.329966] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 29.330146] NFORCE2: IDE controller at PCI slot 0000:00:09.0
[ 29.330245] NFORCE2: chipset revision 162
[ 29.330324] NFORCE2: not 100% native mode: will probe irqs later
[ 29.330413] NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
[ 29.330529] NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
[ 29.330649] NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
[ 29.330740] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[ 29.330945] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
[ 29.331149] Probing IDE interface ide0...
[ 29.617133] hda: WDC WD1000JB-00CRA1, ATA DISK drive
[ 29.738492] ohci1394: fw-host0: SelfID received outside of bus reset sequence
[ 29.960628] hdb: MAXTOR 6L080L4, ATA DISK drive
[ 30.008597] ieee1394: Host added: ID:BUS[0-00:1023] GUID[6e56696469610000]
[ 30.018414] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 30.018604] Probing IDE interface ide1...
[ 30.751469] hdc: LITE-ON LTR-48125W, ATAPI CD/DVD-ROM drive
[ 31.031059] hdd: MAXTOR 6L080J4, ATA DISK drive
[ 31.090564] ide1 at 0x170-0x177,0x376 on irq 15
[ 31.091009] hda: max request size: 128KiB
[ 31.103796] hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
[ 31.104078] hda: cache flushes not supported
[ 31.104194] hda: hda1 hda2 hda3
[ 31.107330] hdb: max request size: 128KiB
[ 31.108443] hdb: 156355584 sectors (80054 MB) w/1819KiB Cache, CHS=65535/16/63, UDMA(133)
[ 31.108865] hdb: cache flushes supported
[ 31.108959] hdb: hdb1
[ 31.112988] hdd: max request size: 128KiB
[ 31.114090] hdd: 156355584 sectors (80054 MB) w/1819KiB Cache, CHS=65535/16/63, UDMA(133)
[ 31.114516] hdd: cache flushes supported
[ 31.114608] hdd: hdd1
[ 31.127946] hdc: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 31.128317] Uniform CD-ROM driver Revision: 3.20
[ 31.167473] sata_sil 0000:01:0b.0: version 2.2
[ 31.167832] ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 11
[ 31.167920] PCI: setting IRQ 11 as level-triggered
[ 31.167924] ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNK3] -> GSI 11 (level, low) -> IRQ 11
[ 31.168212] scsi0 : sata_sil
[ 31.168356] scsi1 : sata_sil
[ 31.168475] ata1: SATA max UDMA/100 cmd 0xe0818080 ctl 0xe081808a bmdma 0xe0818000 irq 0
[ 31.168597] ata2: SATA max UDMA/100 cmd 0xe08180c0 ctl 0xe08180ca bmdma 0xe0818008 irq 0
[ 31.634076] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 31.661140] ata1.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
[ 31.661262] ata1.00: ATA-7: WDC WD3200AAKS-00SBA0, 12.01B01, max UDMA/133
[ 31.661351] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 31.667154] ata1.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
[ 31.667274] ata1.00: configured for UDMA/100
[ 32.133343] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 32.155927] ata2.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
[ 32.156047] ata2.00: ATA-7: WDC WD3200AAKS-00SBA0, 12.01B01, max UDMA/133
[ 32.156136] ata2.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 32.162278] ata2.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
[ 32.162398] ata2.00: configured for UDMA/100
[ 32.162580] scsi 0:0:0:0: Direct-Access ATA WDC WD3200AAKS-0 12.0 PQ: 0 ANSI: 5
[ 32.162805] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 32.162906] sd 0:0:0:0: [sda] Write Protect is off
[ 32.162989] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 32.163003] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.163174] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 32.163271] sd 0:0:0:0: [sda] Write Protect is off
[ 32.163354] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 32.163366] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.163491] sda: unknown partition table
[ 32.172184] sd 0:0:0:0: [sda] Attached SCSI disk
[ 32.172328] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 32.172474] scsi 1:0:0:0: Direct-Access ATA WDC WD3200AAKS-0 12.0 PQ: 0 ANSI: 5
[ 32.172676] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 32.172773] sd 1:0:0:0: [sdb] Write Protect is off
[ 32.172856] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 32.172868] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.173016] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 32.173112] sd 1:0:0:0: [sdb] Write Protect is off
[ 32.173195] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 32.173206] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.173336] sdb: sdb1 sdb2
[ 32.176266] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 32.176405] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 32.176567] sata_via 0000:01:07.0: version 2.1
[ 32.176878] ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 12
[ 32.176966] PCI: setting IRQ 12 as level-triggered
[ 32.176970] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNK4] -> GSI 12 (level, low) -> IRQ 12
[ 32.177246] sata_via 0000:01:07.0: routed to hard irq line 12
[ 32.177404] scsi2 : sata_via
[ 32.177544] scsi3 : sata_via
[ 32.177667] scsi4 : sata_via
[ 32.177782] Bad IO access at port 8 (return inl(port))
[ 32.177866] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.177950] [<c02b7801>] ioread32+0x21/0x30
[ 32.178078] [<c038839c>] sata_scr_read+0x2c/0x50
[ 32.178202] [<c038f260>] ata_interrupt+0x0/0x250
[ 32.178327] [<c038e631>] ata_host_register+0x171/0x2d0
[ 32.178457] [<c038f260>] ata_interrupt+0x0/0x250
[ 32.178580] [<c0145a95>] request_irq+0xb5/0xd0
[ 32.178702] [<c0146f20>] devm_irq_release+0x0/0x10
[ 32.178827] [<c0147010>] devm_request_irq+0x70/0x90
[ 32.178950] [<c038f260>] ata_interrupt+0x0/0x250
[ 32.179073] [<c038e802>] ata_host_activate+0x72/0x90
[ 32.179197] [<c0398b06>] svia_init_one+0x396/0x540
[ 32.179323] [<c01a8cd6>] sysfs_dirent_exist+0x46/0x80
[ 32.179448] [<c01a8e3f>] sysfs_make_dirent+0x2f/0x50
[ 32.179572] [<c02b13b2>] kobject_get+0x12/0x20
[ 32.179698] [<c02c3636>] pci_device_probe+0x56/0x80
[ 32.179822] [<c0320c91>] driver_probe_device+0x91/0x1a0
[ 32.179949] [<c0487a4f>] klist_next+0x6f/0xd0
[ 32.180074] [<c0320edc>] __driver_attach+0x7c/0x80
[ 32.180197] [<c0320074>] bus_for_each_dev+0x44/0x70
[ 32.180321] [<c02b13b2>] kobject_get+0x12/0x20
[ 32.180443] [<c0320b06>] driver_attach+0x16/0x20
[ 32.180565] [<c0320e60>] __driver_attach+0x0/0x80
[ 32.180687] [<c032045a>] bus_add_driver+0x8a/0x1a0
[ 32.180811] [<c01a21df>] create_proc_entry+0x5f/0xd0
[ 32.180937] [<c02c37e9>] __pci_register_driver+0x49/0x90
[ 32.181063] [<c059a740>] kernel_init+0x90/0x260
[ 32.181186] [<c01166df>] schedule_tail+0x2f/0xa0
[ 32.181324] [<c0102de8>] __switch_to+0x28/0x1a0
[ 32.181448] [<c0103f6e>] ret_from_fork+0x6/0x1c
[ 32.181570] [<c059a6b0>] kernel_init+0x0/0x260
[ 32.181691] [<c059a6b0>] kernel_init+0x0/0x260
[ 32.181813] [<c010440f>] kernel_thread_helper+0x7/0x18
[ 32.181938] =======================
[ 32.182017] ata3: SATA max UDMA/133 cmd 0x00019400 ctl 0x0001940a bmdma 0x0001a400 irq 0
[ 32.182136] Bad IO access at port 48 (return inl(port))
[ 32.182220] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.182301] [<c02b7801>] ioread32+0x21/0x30
[ 32.182423] [<c038839c>] sata_scr_read+0x2c/0x50
[ 32.182545] [<c038e631>] ata_host_register+0x171/0x2d0
[ 32.182670] [<c0146f20>] devm_irq_release+0x0/0x10
[ 32.182792] [<c0147010>] devm_request_irq+0x70/0x90
[ 32.182915] [<c038f260>] ata_interrupt+0x0/0x250
[ 32.183038] [<c038e802>] ata_host_activate+0x72/0x90
[ 32.183161] [<c0398b06>] svia_init_one+0x396/0x540
[ 32.183286] [<c01a8cd6>] sysfs_dirent_exist+0x46/0x80
[ 32.183410] [<c01a8e3f>] sysfs_make_dirent+0x2f/0x50
[ 32.183534] [<c02b13b2>] kobject_get+0x12/0x20
[ 32.183656] [<c02c3636>] pci_device_probe+0x56/0x80
[ 32.183779] [<c0320c91>] driver_probe_device+0x91/0x1a0
[ 32.183904] [<c0487a4f>] klist_next+0x6f/0xd0
[ 32.184026] [<c0320edc>] __driver_attach+0x7c/0x80
[ 32.184149] [<c0320074>] bus_for_each_dev+0x44/0x70
[ 32.184273] [<c02b13b2>] kobject_get+0x12/0x20
[ 32.184395] [<c0320b06>] driver_attach+0x16/0x20
[ 32.184518] [<c0320e60>] __driver_attach+0x0/0x80
[ 32.184641] [<c032045a>] bus_add_driver+0x8a/0x1a0
[ 32.184764] [<c01a21df>] create_proc_entry+0x5f/0xd0
[ 32.184888] [<c02c37e9>] __pci_register_driver+0x49/0x90
[ 32.187075] [<c059a740>] kernel_init+0x90/0x260
[ 32.187197] [<c01166df>] schedule_tail+0x2f/0xa0
[ 32.187319] [<c0102de8>] __switch_to+0x28/0x1a0
[ 32.187442] [<c0103f6e>] ret_from_fork+0x6/0x1c
[ 32.187564] [<c059a6b0>] kernel_init+0x0/0x260
[ 32.187686] [<c059a6b0>] kernel_init+0x0/0x260
[ 32.187807] [<c010440f>] kernel_thread_helper+0x7/0x18
[ 32.187931] =======================
[ 32.188010] ata4: SATA max UDMA/133 cmd 0x00019800 ctl 0x0001980a bmdma 0x0001a408 irq 0
[ 32.188130] ata5: PATA max UDMA/133 cmd 0x00019c00 ctl 0x00019c0a bmdma 0x0001a410 irq 0
[ 32.188268] Bad IO access at port 8 (return inl(port))
[ 32.188351] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.188434] [<c02b7801>] ioread32+0x21/0x30
[ 32.188555] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.188681] [<c038839c>] sata_scr_read+0x2c/0x50
[ 32.188803] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.188926] [<c03883dd>] sata_set_spd_needed+0x1d/0x40
[ 32.189050] [<c0394cce>] ata_do_eh+0x84e/0x1aa0
[ 32.189173] [<c02b091f>] _atomic_dec_and_lock+0x2f/0x50
[ 32.189300] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.189424] [<c0172655>] link_path_walk+0x65/0xc0
[ 32.189548] [<c01728be>] do_path_lookup+0x8e/0x250
[ 32.189671] [<c01697df>] get_empty_filp+0x5f/0x120
[ 32.189796] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.189920] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.190043] [<c02b50ee>] vsnprintf+0x34e/0x5d0
[ 32.190168] [<c0102de8>] __switch_to+0x28/0x1a0
[ 32.190290] [<c03938e5>] ata_bmdma_irq_clear+0x15/0x30
[ 32.190415] [<c039379c>] ata_bmdma_drive_eh+0xac/0x140
[ 32.190541] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.190669] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.190793] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.190916] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.191039] [<c0393863>] ata_bmdma_error_handler+0x33/0x40
[ 32.191165] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.191289] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.191412] [<c03965a0>] ata_scsi_error+0x260/0x690
[ 32.191536] [<c0488123>] __sched_text_start+0x283/0x650
[ 32.191661] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.191785] [<c0379080>] scsi_error_handler+0xa0/0x310
[ 32.191911] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.192035] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.192160] [<c012ca82>] kthread+0x42/0x70
[ 32.192281] [<c012ca40>] kthread+0x0/0x70
[ 32.192402] [<c010440f>] kernel_thread_helper+0x7/0x18
[ 32.192526] =======================
[ 32.192604] Bad IO access at port 8 (return inl(port))
[ 32.192688] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.192770] [<c02b7801>] ioread32+0x21/0x30
[ 32.192891] [<c038839c>] sata_scr_read+0x2c/0x50
[ 32.193013] [<c038bab3>] sata_phy_resume+0x23/0x80
[ 32.193136] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.193269] [<c038839c>] sata_scr_read+0x2c/0x50
[ 32.193392] [<c038ede1>] ata_std_prereset+0xb1/0xe0
[ 32.193515] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.193640] [<c0394d18>] ata_do_eh+0x898/0x1aa0
[ 32.193762] [<c02b091f>] _atomic_dec_and_lock+0x2f/0x50
[ 32.193887] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.194011] [<c0172655>] link_path_walk+0x65/0xc0
[ 32.194134] [<c01728be>] do_path_lookup+0x8e/0x250
[ 32.194257] [<c01697df>] get_empty_filp+0x5f/0x120
[ 32.194380] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.194505] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.194628] [<c02b50ee>] vsnprintf+0x34e/0x5d0
[ 32.194750] [<c0102de8>] __switch_to+0x28/0x1a0
[ 32.194872] [<c03938e5>] ata_bmdma_irq_clear+0x15/0x30
[ 32.194996] [<c039379c>] ata_bmdma_drive_eh+0xac/0x140
[ 32.195121] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.195245] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.195368] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.195491] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.195614] [<c0393863>] ata_bmdma_error_handler+0x33/0x40
[ 32.195740] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.195864] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.195987] [<c03965a0>] ata_scsi_error+0x260/0x690
[ 32.196111] [<c0488123>] __sched_text_start+0x283/0x650
[ 32.196236] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.196361] [<c0379080>] scsi_error_handler+0xa0/0x310
[ 32.196487] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.196611] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.196735] [<c012ca82>] kthread+0x42/0x70
[ 32.196856] [<c012ca40>] kthread+0x0/0x70
[ 32.196976] [<c010440f>] kernel_thread_helper+0x7/0x18
[ 32.197102] =======================
[ 32.197180] Bad IO access at port 8 (outl(val,port))
[ 32.197263] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.197345] [<c0388433>] sata_scr_write+0x33/0x50
[ 32.197468] [<c038bae4>] sata_phy_resume+0x54/0x80
[ 32.197592] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.197716] [<c038ede1>] ata_std_prereset+0xb1/0xe0
[ 32.197840] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.197963] [<c0394d18>] ata_do_eh+0x898/0x1aa0
[ 32.198086] [<c02b091f>] _atomic_dec_and_lock+0x2f/0x50
[ 32.198212] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.198335] [<c0172655>] link_path_walk+0x65/0xc0
[ 32.198458] [<c01728be>] do_path_lookup+0x8e/0x250
[ 32.198583] [<c01697df>] get_empty_filp+0x5f/0x120
[ 32.198706] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.198831] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.198954] [<c02b50ee>] vsnprintf+0x34e/0x5d0
[ 32.199076] [<c0102de8>] __switch_to+0x28/0x1a0
[ 32.199198] [<c03938e5>] ata_bmdma_irq_clear+0x15/0x30
[ 32.199323] [<c039379c>] ata_bmdma_drive_eh+0xac/0x140
[ 32.199448] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.199573] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.199696] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.199819] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.199942] [<c0393863>] ata_bmdma_error_handler+0x33/0x40
[ 32.200068] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.200192] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.200315] [<c03965a0>] ata_scsi_error+0x260/0x690
[ 32.200439] [<c0488123>] __sched_text_start+0x283/0x650
[ 32.200564] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.200688] [<c0379080>] scsi_error_handler+0xa0/0x310
[ 32.200814] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.200939] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.201063] [<c012ca82>] kthread+0x42/0x70
[ 32.201184] [<c012ca40>] kthread+0x0/0x70
[ 32.201304] [<c010440f>] kernel_thread_helper+0x7/0x18
[ 32.201429] =======================
[ 32.404922] Bad IO access at port 0 (return inl(port))
[ 32.405006] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.405088] [<c02b7801>] ioread32+0x21/0x30
[ 32.405209] [<c038839c>] sata_scr_read+0x2c/0x50
[ 32.405331] [<c038b9ff>] sata_phy_debounce+0x4f/0xe0
[ 32.405455] [<c038bafa>] sata_phy_resume+0x6a/0x80
[ 32.405578] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.405701] [<c038ede1>] ata_std_prereset+0xb1/0xe0
[ 32.405827] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.405950] [<c0394d18>] ata_do_eh+0x898/0x1aa0
[ 32.406072] [<c02b091f>] _atomic_dec_and_lock+0x2f/0x50
[ 32.406198] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.406322] [<c0172655>] link_path_walk+0x65/0xc0
[ 32.406445] [<c01728be>] do_path_lookup+0x8e/0x250
[ 32.406568] [<c01697df>] get_empty_filp+0x5f/0x120
[ 32.406692] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.406816] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.406939] [<c02b50ee>] vsnprintf+0x34e/0x5d0
[ 32.407061] [<c0102de8>] __switch_to+0x28/0x1a0
[ 32.407183] [<c03938e5>] ata_bmdma_irq_clear+0x15/0x30
[ 32.407308] [<c039379c>] ata_bmdma_drive_eh+0xac/0x140
[ 32.407432] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.407557] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.407680] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.407804] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.407927] [<c0393863>] ata_bmdma_error_handler+0x33/0x40
[ 32.408054] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.408179] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.408302] [<c03965a0>] ata_scsi_error+0x260/0x690
[ 32.408426] [<c0488123>] __sched_text_start+0x283/0x650
[ 32.408551] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.408676] [<c0379080>] scsi_error_handler+0xa0/0x310
[ 32.408801] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.408927] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.409051] [<c012ca82>] kthread+0x42/0x70
[ 32.409172] [<c012ca40>] kthread+0x0/0x70
[ 32.409292] [<c010440f>] kernel_thread_helper+0x7/0x18
[ 32.409417] =======================
[ 32.420898] Bad IO access at port 0 (return inl(port))
[ 32.420981] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.421062] [<c01226b0>] process_timeout+0x0/0x10
[ 32.421185] [<c02b7801>] ioread32+0x21/0x30
[ 32.421308] [<c038839c>] sata_scr_read+0x2c/0x50
[ 32.421430] [<c038ba45>] sata_phy_debounce+0x95/0xe0
[ 32.421553] [<c038bafa>] sata_phy_resume+0x6a/0x80
[ 32.421676] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.421799] [<c038ede1>] ata_std_prereset+0xb1/0xe0
[ 32.421923] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.422048] [<c0394d18>] ata_do_eh+0x898/0x1aa0
[ 32.422171] [<c02b091f>] _atomic_dec_and_lock+0x2f/0x50
[ 32.422295] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.422419] [<c0172655>] link_path_walk+0x65/0xc0
[ 32.422542] [<c01728be>] do_path_lookup+0x8e/0x250
[ 32.422665] [<c01697df>] get_empty_filp+0x5f/0x120
[ 32.422788] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.422912] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.423035] [<c02b50ee>] vsnprintf+0x34e/0x5d0
[ 32.423158] [<c0102de8>] __switch_to+0x28/0x1a0
[ 32.425335] [<c03938e5>] ata_bmdma_irq_clear+0x15/0x30
[ 32.425459] [<c039379c>] ata_bmdma_drive_eh+0xac/0x140
[ 32.425584] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.425709] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.425833] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.425956] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.426079] [<c0393863>] ata_bmdma_error_handler+0x33/0x40
[ 32.426205] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.426329] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.426452] [<c03965a0>] ata_scsi_error+0x260/0x690
[ 32.426576] [<c0488123>] __sched_text_start+0x283/0x650
[ 32.426701] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.426826] [<c0379080>] scsi_error_handler+0xa0/0x310
[ 32.426951] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.427075] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.427200] [<c012ca82>] kthread+0x42/0x70
[ 32.427320] [<c012ca40>] kthread+0x0/0x70
[ 32.427441] [<c010440f>] kernel_thread_helper+0x7/0x18
[ 32.427565] =======================
[ 32.436875] Bad IO access at port 0 (return inl(port))
[ 32.436958] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.437040] [<c01226b0>] process_timeout+0x0/0x10
[ 32.437162] [<c02b7801>] ioread32+0x21/0x30
[ 32.437283] [<c038839c>] sata_scr_read+0x2c/0x50
[ 32.437406] [<c038ba45>] sata_phy_debounce+0x95/0xe0
[ 32.437530] [<c038bafa>] sata_phy_resume+0x6a/0x80
[ 32.437653] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.437776] [<c038ede1>] ata_std_prereset+0xb1/0xe0
[ 32.437900] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.438023] [<c0394d18>] ata_do_eh+0x898/0x1aa0
[ 32.438145] [<c02b091f>] _atomic_dec_and_lock+0x2f/0x50
[ 32.438270] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.438393] [<c0172655>] link_path_walk+0x65/0xc0
[ 32.438519] [<c01728be>] do_path_lookup+0x8e/0x250
[ 32.438642] [<c01697df>] get_empty_filp+0x5f/0x120
[ 32.438766] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.438889] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.439013] [<c02b50ee>] vsnprintf+0x34e/0x5d0
[ 32.439135] [<c0102de8>] __switch_to+0x28/0x1a0
[ 32.439257] [<c03938e5>] ata_bmdma_irq_clear+0x15/0x30
[ 32.439382] [<c039379c>] ata_bmdma_drive_eh+0xac/0x140
[ 32.439507] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.439631] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.439755] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.439879] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.440002] [<c0393863>] ata_bmdma_error_handler+0x33/0x40
[ 32.440128] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.440252] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.440375] [<c03965a0>] ata_scsi_error+0x260/0x690
[ 32.440499] [<c0488123>] __sched_text_start+0x283/0x650
[ 32.440624] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.440749] [<c0379080>] scsi_error_handler+0xa0/0x310
[ 32.440876] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.441000] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.441124] [<c012ca82>] kthread+0x42/0x70
[ 32.441245] [<c012ca40>] kthread+0x0/0x70
[ 32.441365] [<c010440f>] kernel_thread_helper+0x7/0x18
[ 32.441489] =======================
[ 32.452851] Bad IO access at port 0 (return inl(port))
[ 32.452934] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.453016] [<c01226b0>] process_timeout+0x0/0x10
[ 32.453139] [<c02b7801>] ioread32+0x21/0x30
[ 32.453260] [<c038839c>] sata_scr_read+0x2c/0x50
[ 32.453383] [<c038ba45>] sata_phy_debounce+0x95/0xe0
[ 32.453506] [<c038bafa>] sata_phy_resume+0x6a/0x80
[ 32.453629] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.453754] [<c038ede1>] ata_std_prereset+0xb1/0xe0
[ 32.453878] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.454002] [<c0394d18>] ata_do_eh+0x898/0x1aa0
[ 32.454125] [<c02b091f>] _atomic_dec_and_lock+0x2f/0x50
[ 32.454250] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.454373] [<c0172655>] link_path_walk+0x65/0xc0
[ 32.454496] [<c01728be>] do_path_lookup+0x8e/0x250
[ 32.454620] [<c01697df>] get_empty_filp+0x5f/0x120
[ 32.454743] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.454867] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.454990] [<c02b50ee>] vsnprintf+0x34e/0x5d0
[ 32.455113] [<c0102de8>] __switch_to+0x28/0x1a0
[ 32.455234] [<c03938e5>] ata_bmdma_irq_clear+0x15/0x30
[ 32.455359] [<c039379c>] ata_bmdma_drive_eh+0xac/0x140
[ 32.455484] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.455608] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.455731] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.455855] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.455979] [<c0393863>] ata_bmdma_error_handler+0x33/0x40
[ 32.456104] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.456228] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.456351] [<c03965a0>] ata_scsi_error+0x260/0x690
[ 32.456476] [<c0488123>] __sched_text_start+0x283/0x650
[ 32.456601] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.456725] [<c0379080>] scsi_error_handler+0xa0/0x310
[ 32.456851] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.456976] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.457101] [<c012ca82>] kthread+0x42/0x70
[ 32.457221] [<c012ca40>] kthread+0x0/0x70
[ 32.457341] [<c010440f>] kernel_thread_helper+0x7/0x18
[ 32.457465] =======================
[ 32.468828] Bad IO access at port 0 (return inl(port))
[ 32.468911] BUG: at lib/iomap.c:44 bad_io_access()
[ 32.468993] [<c01226b0>] process_timeout+0x0/0x10
[ 32.469117] [<c02b7801>] ioread32+0x21/0x30
[ 32.469238] [<c038839c>] sata_scr_read+0x2c/0x50
[ 32.469362] [<c038ba45>] sata_phy_debounce+0x95/0xe0
[ 32.469486] [<c038bafa>] sata_phy_resume+0x6a/0x80
[ 32.469609] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.469733] [<c038ede1>] ata_std_prereset+0xb1/0xe0
[ 32.469857] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.469981] [<c0394d18>] ata_do_eh+0x898/0x1aa0
[ 32.470104] [<c02b091f>] _atomic_dec_and_lock+0x2f/0x50
[ 32.470228] [<c017f9c6>] mntput_no_expire+0x16/0xa0
[ 32.470352] [<c0172655>] link_path_walk+0x65/0xc0
[ 32.470475] [<c01728be>] do_path_lookup+0x8e/0x250
[ 32.470598] [<c01697df>] get_empty_filp+0x5f/0x120
[ 32.470720] [<c038b710>] ata_std_softreset+0x0/0x110
[ 32.470844] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.470967] [<c02b50ee>] vsnprintf+0x34e/0x5d0
[ 32.471090] [<c0102de8>] __switch_to+0x28/0x1a0
[ 32.471211] [<c03938e5>] ata_bmdma_irq_clear+0x15/0x30
[ 32.471336] [<c039379c>] ata_bmdma_drive_eh+0xac/0x140
[ 32.471460] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.471585] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.471709] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.471832] [<c038ed30>] ata_std_prereset+0x0/0xe0
[ 32.471955] [<c0393863>] ata_bmdma_error_handler+0x33/0x40
[ 32.472082] [<c038bbe0>] sata_std_hardreset+0x0/0xc0
[ 32.472205] [<c038b430>] ata_std_postreset+0x0/0xb0
[ 32.472328] [<c03965a0>] ata_scsi_error+0x260/0x690
[ 32.472453] [<c0488123>] __sched_text_start+0x283/0x650
[ 32.472577] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.472702] [<c0379080>] scsi_error_handler+0xa0/0x310
[ 32.472828] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.472954] [<c0378fe0>] scsi_error_handler+0x0/0x310
[ 32.473079] [<c012ca82>] kthread+0x42/0x70
[ 32.473199] [<c012ca40>] kthread+0x0/0x70
[ 32.473319] [<c010440f>] kernel_thread_helper+0x7/0x18
[ 32.473444] =======================
[ 32.520755] ata3: SATA link down (SStatus FFFFFFFF SControl FFFFFFFF)
[ 32.832296] ata4: SATA link down (SStatus FFFFFFFF SControl FFFFFFFF)
[ 32.999603] ATA: abnormal status 0x8 on port 0x00019c07
[ 32.999745] ieee1394: raw1394: /dev/raw1394 device initialized
[ 32.999986] eth1394: eth2: IPv4 over IEEE 1394 (fw-host0)
[ 33.000555] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 9
[ 33.000643] ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUB2] -> GSI 9 (level, low) -> IRQ 9
[ 33.000854] PCI: Setting latency timer of device 0000:00:02.2 to 64
[ 33.000858] ehci_hcd 0000:00:02.2: EHCI Host Controller
[ 33.001004] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
[ 33.001161] ehci_hcd 0000:00:02.2: debug port 1
[ 33.001245] PCI: cache line size of 64 is not supported by device 0000:00:02.2
[ 33.001254] ehci_hcd 0000:00:02.2: irq 9, io mem 0xe8085000
[ 33.001345] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 33.001618] usb usb1: configuration #1 chosen from 1 choice
[ 33.001747] hub 1-0:1.0: USB hub found
[ 33.001837] hub 1-0:1.0: 6 ports detected
[ 33.103961] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 33.104247] ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 12
[ 33.104334] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUBA] -> GSI 12 (level, low) -> IRQ 12
[ 33.104544] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 33.104548] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 33.104667] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 33.104796] ohci_hcd 0000:00:02.0: irq 12, io mem 0xe8081000
[ 33.161904] usb usb2: configuration #1 chosen from 1 choice
[ 33.162024] hub 2-0:1.0: USB hub found
[ 33.162114] hub 2-0:1.0: 3 ports detected
[ 33.263929] ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 11
[ 33.264016] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUBB] -> GSI 11 (level, low) -> IRQ 11
[ 33.264224] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 33.264227] ohci_hcd 0000:00:02.1: OHCI Host Controller
[ 33.264347] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
[ 33.264473] ohci_hcd 0000:00:02.1: irq 11, io mem 0xe8084000
[ 33.321677] usb usb3: configuration #1 chosen from 1 choice
[ 33.321803] hub 3-0:1.0: USB hub found
[ 33.321892] hub 3-0:1.0: 3 ports detected
[ 33.423489] USB Universal Host Controller Interface driver v3.0
[ 33.782903] usb 3-1: new low speed USB device using ohci_hcd and address 2
[ 33.949621] usb 3-1: configuration #1 chosen from 1 choice
[ 34.108086] ohci1394: fw-host0: SelfID received outside of bus reset sequence
[ 34.298147] usb 3-2: new full speed USB device using ohci_hcd and address 3
[ 34.465758] usb 3-2: configuration #1 chosen from 1 choice
[ 34.475708] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04E8 pid 0x326C
[ 34.475850] usbcore: registered new interface driver usblp
[ 34.475936] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 34.476027] Initializing USB Mass Storage driver...
[ 34.476148] usbcore: registered new interface driver usb-storage
[ 34.476235] USB Mass Storage support registered.
[ 34.476388] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 34.476476] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 34.725901] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 34.726079] mice: PS/2 mouse device common for all mice
[ 34.752830] input: AT Translated Set 2 keyboard as /class/input/input2
[ 34.752935] md: raid0 personality registered for level 0
[ 34.753086] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 34.760441] input: Logitech USB-PS/2 Mouse as /class/input/input3
[ 34.760564] input: USB HID v1.00 Mouse [Logitech USB-PS/2 Mouse] on usb-0000:00:02.1-1
[ 34.760779] usbcore: registered new interface driver usbhid
[ 34.760866] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 34.760981] Advanced Linux Sound Architecture Driver Version 1.0.14rc4 (Wed May 09 09:51:39 2007 UTC).
[ 34.761105] ALSA device list:
[ 34.761193] No soundcards found.
[ 34.761292] IPv4 over IPv4 tunneling driver
[ 34.761445] GRE over IPv4 tunneling driver
[ 34.761604] TCP cubic registered
[ 34.761688] NET: Registered protocol family 1
[ 34.761771] NET: Registered protocol family 17
[ 34.761889] Testing NMI watchdog ... OK.
[ 34.841339] Using IPI Shortcut mode
[ 34.841716] md: Autodetecting RAID arrays.
[ 34.841798] md: autorun ...
[ 34.841873] md: ... autorun DONE.
[ 34.858241] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 34.858339] ReiserFS: hda2: using ordered data mode
[ 34.863578] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 34.865233] ReiserFS: hda2: checking transaction log (hda2)
[ 34.910846] ReiserFS: hda2: Using r5 hash to sort names
[ 34.910956] VFS: Mounted root (reiserfs filesystem) readonly.
[ 34.911341] Freeing unused kernel memory: 208k freed
[ 37.908491] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000
[ 37.908514] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5500
[ 38.441337] ACPI: PCI Interrupt Link [LACI] enabled at IRQ 11
[ 38.441343] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LACI] -> GSI 11 (level, low) -> IRQ 11
[ 38.441372] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 38.759638] intel8x0_measure_ac97_clock: measured 52781 usecs
[ 38.759644] intel8x0: clocking to 47503
[ 56.760486] ReiserFS: dm-0: found reiserfs format "3.6" with standard journal
[ 56.760507] ReiserFS: dm-0: using ordered data mode
[ 56.760684] ReiserFS: dm-0: journal params: device dm-0, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 56.762260] ReiserFS: dm-0: checking transaction log (dm-0)
[ 56.779528] ReiserFS: dm-0: Using r5 hash to sort names
[ 60.316791] Adding 2097144k swap on /mnt/raidchunk/swapfile.bin. Priority:-1 extents:457 across:2100884k
[ 65.504930] eth1: no link during initialization.
[ 91.651175] eth0: network connection up using port A
[ 91.651182] speed: 1000
[ 91.651184] autonegotiation: yes
[ 91.651185] duplex mode: full
[ 91.651187] flowctrl: symmetric
[ 91.651189] role: slave
[ 91.651190] irq moderation: disabled
[ 91.651192] scatter-gather: disabled
[ 91.651194] tx-checksum: disabled
[ 91.651195] rx-checksum: disabled
[-- Attachment #3: dmesg_subsection-2.6.21.1.txt --]
[-- Type: text/plain, Size: 2809 bytes --]
[ 30.980942] sata_via 0000:01:07.0: version 2.1
[ 30.981275] ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 12
[ 30.981279] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNK4] -> GSI 12 (level, low) -> IRQ 12
[ 30.981298] sata_via 0000:01:07.0: routed to hard irq line 12
[ 30.981367] ata3: SATA max UDMA/133 cmd 0x00019400 ctl 0x0001940a bmdma 0x0001a400 irq 12
[ 30.981403] ata4: SATA max UDMA/133 cmd 0x00019800 ctl 0x0001980a bmdma 0x0001a408 irq 12
[ 30.981437] ata5: PATA max UDMA/133 cmd 0x00019c00 ctl 0x00019c0a bmdma 0x0001a410 irq 12
[ 30.981454] scsi2 : sata_via
[ 31.120479] ACPI: PCI Interrupt Link [LACI] enabled at IRQ 11
[ 31.120486] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LACI] -> GSI 11 (level, low) -> IRQ 11
[ 31.120520] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 31.135776] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 31.144016] ata3.00: ATA-7: WDC WD3200AAKS-00SBA0, 12.01B01, max UDMA/133
[ 31.144021] ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 31.152025] ata3.00: configured for UDMA/133
[ 31.152047] scsi3 : sata_via
[ 31.307512] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 31.324869] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[ 31.443258] intel8x0_measure_ac97_clock: measured 52722 usecs
[ 31.443264] intel8x0: clocking to 47450
[ 31.982496] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 31.995489] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[ 31.995495] ata4.00: limiting speed to UDMA7:PIO5
[ 32.653509] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 32.666118] ata4.00: ATA-7: WDC WD3200AAKS-00SBA0, 12.01B01, max UDMA/133
[ 32.666122] ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 32.680112] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[ 32.680115] ata4.00: revalidation failed (errno=-5)
[ 32.680117] ata4.00: disabled
[ 33.180715] scsi4 : sata_via
[ 33.348013] ATA: abnormal status 0x8 on port 0x00019c07
[ 33.348122] scsi 2:0:0:0: Direct-Access ATA WDC WD3200AAKS-0 12.0 PQ: 0 ANSI: 5
[ 33.348313] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
[ 33.348327] sdc: Write Protect is off
[ 33.348329] sdc: Mode Sense: 00 3a 00 00
[ 33.348344] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.348412] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
[ 33.348422] sdc: Write Protect is off
[ 33.348424] sdc: Mode Sense: 00 3a 00 00
[ 33.348438] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.348442] sdc: unknown partition table
[ 33.364613] sd 2:0:0:0: Attached scsi disk sdc
[ 33.364769] sd 2:0:0:0: Attached scsi generic sg2 type 0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH] sata_via: pcim_iomap_regions() conversion missed BAR5
2007-05-17 10:09 sata_via, 2.6.22-rc1, VT6421A Tim Valenzuela
@ 2007-05-17 11:37 ` Tejun Heo
2007-05-17 13:40 ` Tim Valenzuela
2007-05-18 0:59 ` Jeff Garzik
0 siblings, 2 replies; 6+ messages in thread
From: Tejun Heo @ 2007-05-17 11:37 UTC (permalink / raw)
To: Tim Valenzuela, Jeff Garzik; +Cc: IDE/ATA development list
pcim_iomap_regions() conversion missed BAR5. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
---
Sorry, dunno how I missed that during testing. :-( Please verify this
fixes your problem.
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index d105d2c..ac4f43c 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -441,7 +441,7 @@ static int vt6421_prepare_host(struct pc
return -ENOMEM;
}
- rc = pcim_iomap_regions(pdev, 0x1f, DRV_NAME);
+ rc = pcim_iomap_regions(pdev, 0x3f, DRV_NAME);
if (rc) {
dev_printk(KERN_ERR, &pdev->dev, "failed to request/iomap "
"PCI BARs (errno=%d)\n", rc);
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH] sata_via: pcim_iomap_regions() conversion missed BAR5
2007-05-17 11:37 ` [PATCH] sata_via: pcim_iomap_regions() conversion missed BAR5 Tejun Heo
@ 2007-05-17 13:40 ` Tim Valenzuela
2007-05-17 13:49 ` Tejun Heo
2007-05-18 0:59 ` Jeff Garzik
1 sibling, 1 reply; 6+ messages in thread
From: Tim Valenzuela @ 2007-05-17 13:40 UTC (permalink / raw)
To: Tejun Heo; +Cc: Jeff Garzik, IDE/ATA development list
Good news: This patch does correct the IO access errors.
Bad news: The sata driver now performs exactly like previous kernels, my
sata3 works, sata4 has IDENTIFY errors.
[ 26.927349] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 26.961636] ata4.00: ata_hpa_resize 1: sectors = 625142448,
hpa_sectors = 625142448
[ 26.961754] ata4.00: ATA-7: WDC WD3200AAKS-00SBA0, 12.01B01, max UDMA/133
[ 26.961843] ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 26.979289] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[ 26.979376] ata4.00: revalidation failed (errno=-5)
[ 26.979458] ata4: failed to recover some devices, retrying in 5 secs
[ 32.451247] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 32.475231] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[ 32.475317] ata4.00: revalidation failed (errno=-5)
[ 32.475401] ata4.00: limiting speed to UDMA/133:PIO3
[ 32.475483] ata4: failed to recover some devices, retrying in 5 secs
[ 37.947188] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 37.971173] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[ 37.971259] ata4.00: revalidation failed (errno=-5)
[ 37.971341] ata4.00: disabled
Is the VT6421A supported with both sata channels? In an earlier
revision, this card used to come with a VT6421L instead (based on
information I find on the Google).
Thanks,
Tim Valenzuela
Tejun Heo wrote:
> pcim_iomap_regions() conversion missed BAR5. Fix it.
>
> Signed-off-by: Tejun Heo <htejun@gmail.com>
> ---
> Sorry, dunno how I missed that during testing. :-( Please verify this
> fixes your problem.
>
> diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
> index d105d2c..ac4f43c 100644
> --- a/drivers/ata/sata_via.c
> +++ b/drivers/ata/sata_via.c
> @@ -441,7 +441,7 @@ static int vt6421_prepare_host(struct pc
> return -ENOMEM;
> }
>
> - rc = pcim_iomap_regions(pdev, 0x1f, DRV_NAME);
> + rc = pcim_iomap_regions(pdev, 0x3f, DRV_NAME);
> if (rc) {
> dev_printk(KERN_ERR, &pdev->dev, "failed to request/iomap "
> "PCI BARs (errno=%d)\n", rc);
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] sata_via: pcim_iomap_regions() conversion missed BAR5
2007-05-17 13:40 ` Tim Valenzuela
@ 2007-05-17 13:49 ` Tejun Heo
2007-05-17 15:37 ` Tim Valenzuela
0 siblings, 1 reply; 6+ messages in thread
From: Tejun Heo @ 2007-05-17 13:49 UTC (permalink / raw)
To: Tim Valenzuela; +Cc: Jeff Garzik, IDE/ATA development list
Tim Valenzuela wrote:
> Good news: This patch does correct the IO access errors.
> Bad news: The sata driver now performs exactly like previous kernels, my
> sata3 works, sata4 has IDENTIFY errors.
The patch doesn't do anything about that problem, so it's expected.
> [ 26.927349] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 26.961636] ata4.00: ata_hpa_resize 1: sectors = 625142448,
> hpa_sectors = 625142448
> [ 26.961754] ata4.00: ATA-7: WDC WD3200AAKS-00SBA0, 12.01B01, max
> UDMA/133
> [ 26.961843] ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
> [ 26.979289] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
> [ 26.979376] ata4.00: revalidation failed (errno=-5)
> [ 26.979458] ata4: failed to recover some devices, retrying in 5 secs
> [ 32.451247] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 32.475231] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
> [ 32.475317] ata4.00: revalidation failed (errno=-5)
> [ 32.475401] ata4.00: limiting speed to UDMA/133:PIO3
> [ 32.475483] ata4: failed to recover some devices, retrying in 5 secs
> [ 37.947188] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 37.971173] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
> [ 37.971259] ata4.00: revalidation failed (errno=-5)
> [ 37.971341] ata4.00: disabled
Can you swap the two disks and see what happens? It seems the second
IDENTIFY after configuring transfer mode fails. I'm curious whether
that's caused by the disk or the controller.
--
tejun
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] sata_via: pcim_iomap_regions() conversion missed BAR5
2007-05-17 13:49 ` Tejun Heo
@ 2007-05-17 15:37 ` Tim Valenzuela
0 siblings, 0 replies; 6+ messages in thread
From: Tim Valenzuela @ 2007-05-17 15:37 UTC (permalink / raw)
To: Tejun Heo; +Cc: Jeff Garzik, IDE/ATA development list
[-- Attachment #1: Type: text/plain, Size: 1953 bytes --]
I swapped the drives out and I got identical results, which means the
problem lies in the driver or the card itself....
I moved the card to a win32 machine to see what the official driver
would do. It failed on the 2nd sata channel too. So I'm gonna conclude
its physically broken. Sorry for the trouble.
Tim Valenzuela
Tejun Heo wrote:
> Tim Valenzuela wrote:
>
>> Good news: This patch does correct the IO access errors.
>> Bad news: The sata driver now performs exactly like previous kernels, my
>> sata3 works, sata4 has IDENTIFY errors.
>>
>
> The patch doesn't do anything about that problem, so it's expected.
>
>
>> [ 26.927349] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>> [ 26.961636] ata4.00: ata_hpa_resize 1: sectors = 625142448,
>> hpa_sectors = 625142448
>> [ 26.961754] ata4.00: ATA-7: WDC WD3200AAKS-00SBA0, 12.01B01, max
>> UDMA/133
>> [ 26.961843] ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
>> [ 26.979289] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
>> [ 26.979376] ata4.00: revalidation failed (errno=-5)
>> [ 26.979458] ata4: failed to recover some devices, retrying in 5 secs
>> [ 32.451247] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>> [ 32.475231] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
>> [ 32.475317] ata4.00: revalidation failed (errno=-5)
>> [ 32.475401] ata4.00: limiting speed to UDMA/133:PIO3
>> [ 32.475483] ata4: failed to recover some devices, retrying in 5 secs
>> [ 37.947188] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>> [ 37.971173] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x1)
>> [ 37.971259] ata4.00: revalidation failed (errno=-5)
>> [ 37.971341] ata4.00: disabled
>>
>
> Can you swap the two disks and see what happens? It seems the second
> IDENTIFY after configuring transfer mode fails. I'm curious whether
> that's caused by the disk or the controller.
>
>
[-- Attachment #2: in_windows_too.png --]
[-- Type: image/png, Size: 30004 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] sata_via: pcim_iomap_regions() conversion missed BAR5
2007-05-17 11:37 ` [PATCH] sata_via: pcim_iomap_regions() conversion missed BAR5 Tejun Heo
2007-05-17 13:40 ` Tim Valenzuela
@ 2007-05-18 0:59 ` Jeff Garzik
1 sibling, 0 replies; 6+ messages in thread
From: Jeff Garzik @ 2007-05-18 0:59 UTC (permalink / raw)
To: Tejun Heo; +Cc: Tim Valenzuela, IDE/ATA development list
Tejun Heo wrote:
> pcim_iomap_regions() conversion missed BAR5. Fix it.
>
> Signed-off-by: Tejun Heo <htejun@gmail.com>
> ---
> Sorry, dunno how I missed that during testing. :-( Please verify this
> fixes your problem.
>
> diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
> index d105d2c..ac4f43c 100644
> --- a/drivers/ata/sata_via.c
> +++ b/drivers/ata/sata_via.c
> @@ -441,7 +441,7 @@ static int vt6421_prepare_host(struct pc
> return -ENOMEM;
> }
>
> - rc = pcim_iomap_regions(pdev, 0x1f, DRV_NAME);
> + rc = pcim_iomap_regions(pdev, 0x3f, DRV_NAME);
> if (rc) {
> dev_printk(KERN_ERR, &pdev->dev, "failed to request/iomap "
> "PCI BARs (errno=%d)\n", rc);
applied.
Please figure out a better method than raw hex numbers for the mask...
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2007-05-18 0:59 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-05-17 10:09 sata_via, 2.6.22-rc1, VT6421A Tim Valenzuela
2007-05-17 11:37 ` [PATCH] sata_via: pcim_iomap_regions() conversion missed BAR5 Tejun Heo
2007-05-17 13:40 ` Tim Valenzuela
2007-05-17 13:49 ` Tejun Heo
2007-05-17 15:37 ` Tim Valenzuela
2007-05-18 0:59 ` Jeff Garzik
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).