From: "Ole-Christian S. Hagenes" <ole@fjordn.net>
To: linux-ide@vger.kernel.org
Subject: Problems with the sata_promise driver while using smart.
Date: Mon, 13 Aug 2007 17:01:21 +0200 [thread overview]
Message-ID: <46C07241.7010605@fjordn.net> (raw)
I have experienced some problems with the sata_promise driver on a
FastTrak4000 card. Doing smart-requests, like munins hddtemp_smartctl
plugin, to the disks while under load, makes the drives randomly timeout.
ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.00: cmd c8/00:08:d7:b3:ce/00:00:00:00:00/e1 tag 0 cdb 0x0 data \
4096 in
res 40/00:01:01:4f:c2/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata3: soft resetting port
ata3.00: configured for UDMA/100
ata3: EH complete
sd 3:0:0:0: [sde] 361882080 512-byte hardware sectors (185284 MB)
sd 3:0:0:0: [sde] Write Protect is off
sd 3:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't\
support DPO or FUA
Turning off the hddtempt_smartctl plugin in munin makes this problem go
away. I am currently running 2.6.22.2 on debian stable compiled with
mostly everything as a module. I used the debian-config for 2.6.18 and
did make oldconfig.
I have made attempts to figure out if its disk og driver/card related by
swapping disks around, and the same error occurs with different disks on
the same card. But it doesnt follow the disks.
Is it expected behaviour that smart makes the drives timeout or is
something wrong?
As the machine doesnt hold any valuable data at the moment, I am more
then happy try out patches etc.
The complete dmesg:
klogd 1.4.1#18, log source = /proc/kmsg started.
Linux version 2.6.22.2 (ochagenes@litago) (gcc version 4.1.2 20061115
(prerelease) (Debian 4.1.1-21)) #1 SMP Sun Aug 12 02:55:57 BST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 0000000000100000 - 000000003ffe0000 (usable)
BIOS-e820: 000000003ffe0000 - 000000003ffefc00 (ACPI data)
BIOS-e820: 000000003ffefc00 - 000000003ffff000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262112
early_node_map[1] active PFN ranges
0: 0 -> 262112
DMI 2.3 present.
ACPI: RSDP 000FDC40, 0014 (r0 DELL )
ACPI: RSDT 000FDC54, 0030 (r1 DELL PE1600SC 1 MSFT 100000A)
ACPI: FACP 000FDC84, 0074 (r1 DELL PE1600SC 1 MSFT 100000A)
ACPI: DSDT 3FFE0000, 3121 (r1 DELL PE1600SC 1 MSFT 100000A)
ACPI: FACS 3FFEFC00, 0040
ACPI: APIC 000FDCF8, 0088 (r1 DELL PE1600SC 1 MSFT 100000A)
ACPI: SPCR 000FDD80, 0050 (r1 DELL PE1600SC 1 MSFT 100000A)
ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x06] enabled)
Processor #6 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x09] address[0xfec01000] gsi_base[16])
IOAPIC[1]: apic_id 9, version 17, address 0xfec01000, GSI 16-31
ACPI: IOAPIC (id[0x0a] address[0xfec02000] gsi_base[32])
IOAPIC[2]: apic_id 10, version 17, address 0xfec02000, GSI 32-47
Enabling APIC mode: Flat. Using 3 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3ffff000:bec01000)
Built 1 zonelists. Total pages: 260065
Kernel command line: auto BOOT_IMAGE=Linux ro root=900
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2790.945 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030536k/1048448k available (1668k kernel code, 17356k
reserved, 639k data, 224k init, 130944k highmem)
virtual kernel memory layout:
fixmap : 0xfff4f000 - 0xfffff000 ( 704 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0347000 - 0xc037f000 ( 224 kB)
.data : 0xc02a1039 - 0xc0340f44 ( 639 kB)
.text : 0xc0100000 - 0xc02a1039 (1668 kB)
Checking if this processor honours the WP bit even in supervisor
mode... Ok.
Calibrating delay using timer specific routine.. 5585.91 BogoMIPS
(lpj=11171822)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
SMP alternatives: switching to SMP code
Booting processor 1/6 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5581.87 BogoMIPS
(lpj=11163752)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
Total of 2 processors activated (11167.78 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=1164
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfc68e, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Root Bridge [PCI1] (0000:01)
ACPI: PCI Root Bridge [PCI2] (0000:02)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNK6] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs *3 4 5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNK9] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN10] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN11] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN12] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN13] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN14] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN15] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN16] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN17] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN18] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN19] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN1A] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN1B] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN1C] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN1D] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN1E] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LN1F] (IRQs 3 4 5 6 7 9 10 11 12 14) *0,
disabled.
ACPI: PCI Interrupt Link [LUSB] (IRQs 3 4 5 6 7 *10 11 12 14)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post
a report
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: RTC can wake from S4
pnp: 00:09: ioport range 0x814-0x85b has been reserved
pnp: 00:09: ioport range 0x820-0x83f has been reserved
pnp: 00:09: ioport range 0x8a0-0x8af has been reserved
pnp: 00:09: ioport range 0xc00-0xcd7 has been reserved
pnp: 00:09: ioport range 0xf50-0xf58 has been reserved
pnp: 00:09: ioport range 0x800-0x819 could not be reserved
pnp: 00:09: ioport range 0x880-0x89f has been reserved
pnp: 00:09: ioport range 0x8c0-0x8c3 has been reserved
pnp: 00:0a: iomem range 0x0-0x0 could not be reserved
pnp: 00:0a: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0a: iomem range 0x100000-0x3fffffff could not be reserved
pnp: 00:0a: iomem range 0xf0000-0xfffff could not be reserved
Time: tsc clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5458k freed
audit: initializing netlink socket (disabled)
audit(1186919226.000:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: MSI quirk detected. MSI deactivated.
PCI: MSI quirk detected. MSI deactivated.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBD] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
Freeing unused kernel memory: 224k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device
is not present [20070126]
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device
is not present [20070126]
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
SCSI subsystem initialized
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
e1000: 0000:00:02.0: e1000_probe: (PCI:33MHz:32-bit) 00:11:43:d1:19:d8
Fusion MPT SPI Host driver 3.04.04
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
scsi0 : pata_serverworks
scsi1 : pata_serverworks
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x000108b0
irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x000108b8
irq 15
ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 29 (level, low) -> IRQ 17
mptbase: Initiating ioc0 bringup
ACPI: PCI Interrupt Link [LUSB] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:0f.2[A] -> Link [LUSB] -> GSI 10 (level,
low) -> IRQ 10
ohci_hcd 0000:00:0f.2: OHCI Host Controller
ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0f.2: irq 10, io mem 0xfe120000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ioc0: 53C1030: Capabilities={Initiator,Target}
scsi2 : ioc0: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=255, IRQ=17
scsi 2:0:4:0: Direct-Access MAXTOR ATLAS10K4_73WLS DFV0 PQ: 0
ANSI: 3
target2:0:4: Beginning Domain Validation
target2:0:4: Ending Domain Validation
target2:0:4: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI (6.25 ns, offset
127)
scsi 2:0:6:0: Direct-Access MAXTOR ATLAS10K4_73WLS DFV0 PQ: 0
ANSI: 3
target2:0:6: Beginning Domain Validation
target2:0:6: Ending Domain Validation
target2:0:6: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI (6.25 ns, offset
127)
ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 21 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 17 (level, low) -> IRQ 19
scsi3 : sata_promise
scsi4 : sata_promise
scsi5 : sata_promise
scsi6 : sata_promise
ata3: PATA max UDMA/133 cmd 0xf8832200 ctl 0xf8832238 bmdma 0x00000000
irq 18
ata4: PATA max UDMA/133 cmd 0xf8832280 ctl 0xf88322b8 bmdma 0x00000000
irq 18
ata5: PATA max UDMA/133 cmd 0xf8832300 ctl 0xf8832338 bmdma 0x00000000
irq 18
ata6: PATA max UDMA/133 cmd 0xf8832380 ctl 0xf88323b8 bmdma 0x00000000
irq 18
pata_pdc2027x 0000:01:02.0: PLL input clock 33216 kHz
scsi7 : pata_pdc2027x
scsi8 : pata_pdc2027x
ata7: PATA max UDMA/133 cmd 0xf88c17c0 ctl 0xf88c1fda bmdma 0xf88c1000
irq 19
ata8: PATA max UDMA/133 cmd 0xf88c15c0 ctl 0xf88c1dda bmdma 0xf88c1008
irq 19
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
sd 2:0:4:0: [sda] 143666192 512-byte hardware sectors (73557 MB)
sd 2:0:4:0: [sda] Write Protect is off
sd 2:0:4:0: [sda] Write cache: enabled, read cache: enabled, supports
DPO and FUA
sd 2:0:4:0: [sda] 143666192 512-byte hardware sectors (73557 MB)
sd 2:0:4:0: [sda] Write Protect is off
sd 2:0:4:0: [sda] Write cache: enabled, read cache: enabled, supports
DPO and FUA
sda: sda1
sd 2:0:4:0: [sda] Attached SCSI disk
sd 2:0:6:0: [sdb] 143666192 512-byte hardware sectors (73557 MB)
sd 2:0:6:0: [sdb] Write Protect is off
sd 2:0:6:0: [sdb] Write cache: enabled, read cache: enabled, supports
DPO and FUA
sd 2:0:6:0: [sdb] 143666192 512-byte hardware sectors (73557 MB)
sd 2:0:6:0: [sdb] Write Protect is off
sd 2:0:6:0: [sdb] Write cache: enabled, read cache: enabled, supports
DPO and FUA
sdb: sdb1
sd 2:0:6:0: [sdb] Attached SCSI disk
ata3.00: ATA-6: IC35L180AVV207-1, V26OA66A, max UDMA/100
ata3.00: 361882080 sectors, multi 0: LBA48
ata3.00: configured for UDMA/100
ata7.01: ATA-7: Maxtor 6Y200P0, YAR41VW0, max UDMA/133
ata7.01: 398297088 sectors, multi 16: LBA48
ata7.01: configured for UDMA/133
ata4.00: ATA-6: IC35L180AVV207-1, V26OA66A, max UDMA/100
ata4.00: 361882080 sectors, multi 0: LBA48
ata4.00: configured for UDMA/100
ata8.01: ATA-7: Maxtor 6Y200P0, YAR41VW0, max UDMA/133
ata8.01: 398297088 sectors, multi 16: LBA48
ata8.01: configured for UDMA/133
scsi 7:0:1:0: Direct-Access ATA Maxtor 6Y200P0 YAR4 PQ: 0
ANSI: 5
sd 7:0:1:0: [sdc] 398297088 512-byte hardware sectors (203928 MB)
sd 7:0:1:0: [sdc] Write Protect is off
sd 7:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 7:0:1:0: [sdc] 398297088 512-byte hardware sectors (203928 MB)
sd 7:0:1:0: [sdc] Write Protect is off
sd 7:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdc: sdc1 sdc2
sd 7:0:1:0: [sdc] Attached SCSI disk
scsi 8:0:1:0: Direct-Access ATA Maxtor 6Y200P0 YAR4 PQ: 0
ANSI: 5
sd 8:0:1:0: [sdd] 398297088 512-byte hardware sectors (203928 MB)
sd 8:0:1:0: [sdd] Write Protect is off
sd 8:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 8:0:1:0: [sdd] 398297088 512-byte hardware sectors (203928 MB)
sd 8:0:1:0: [sdd] Write Protect is off
sd 8:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdd: sdd1 sdd2
sd 8:0:1:0: [sdd] Attached SCSI disk
ACPI: PCI Interrupt 0000:01:06.0[A] -> GSI 20 (level, low) -> IRQ 20
ata5.00: ATA-6: IC35L180AVV207-1, V26OA66A, max UDMA/100
ata5.00: 361882080 sectors, multi 0: LBA48
ata5.00: configured for UDMA/100
pata_pdc2027x 0000:01:06.0: PLL input clock 33216 kHz
scsi9 : pata_pdc2027x
scsi10 : pata_pdc2027x
ata9: PATA max UDMA/133 cmd 0xf89497c0 ctl 0xf8949fda bmdma 0xf8949000
irq 20
ata10: PATA max UDMA/133 cmd 0xf89495c0 ctl 0xf8949dda bmdma
0xf8949008 irq 20
ata6.00: ATA-6: IC35L180AVV207-1, V26OA66A, max UDMA/100
ata6.00: 361882080 sectors, multi 0: LBA48
ata6.00: configured for UDMA/100
scsi 3:0:0:0: Direct-Access ATA IC35L180AVV207-1 V26O PQ: 0
ANSI: 5
sd 3:0:0:0: [sde] 361882080 512-byte hardware sectors (185284 MB)
sd 3:0:0:0: [sde] Write Protect is off
sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 3:0:0:0: [sde] 361882080 512-byte hardware sectors (185284 MB)
sd 3:0:0:0: [sde] Write Protect is off
sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sde: sde1
sd 3:0:0:0: [sde] Attached SCSI disk
scsi 4:0:0:0: Direct-Access ATA IC35L180AVV207-1 V26O PQ: 0
ANSI: 5
sd 4:0:0:0: [sdf] 361882080 512-byte hardware sectors (185284 MB)
sd 4:0:0:0: [sdf] Write Protect is off
sd 4:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 4:0:0:0: [sdf] 361882080 512-byte hardware sectors (185284 MB)
sd 4:0:0:0: [sdf] Write Protect is off
sd 4:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdf: sdf1
sd 4:0:0:0: [sdf] Attached SCSI disk
scsi 5:0:0:0: Direct-Access ATA IC35L180AVV207-1 V26O PQ: 0
ANSI: 5
sd 5:0:0:0: [sdg] 361882080 512-byte hardware sectors (185284 MB)
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 5:0:0:0: [sdg] 361882080 512-byte hardware sectors (185284 MB)
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdg:<6>ata9.01: ATA-6: WDC WD2000BB-22GUA0, 08.02D08, max UDMA/100
ata9.01: 390721968 sectors, multi 16: LBA48
sdg1
sd 5:0:0:0: [sdg] Attached SCSI disk
scsi 6:0:0:0: Direct-Access ATA IC35L180AVV207-1 V26O PQ: 0
ANSI: 5
sd 6:0:0:0: [sdh] 361882080 512-byte hardware sectors (185284 MB)
sd 6:0:0:0: [sdh] Write Protect is off
sd 6:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 6:0:0:0: [sdh] 361882080 512-byte hardware sectors (185284 MB)
sd 6:0:0:0: [sdh] Write Protect is off
sd 6:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdh:<6>ata9.01: configured for UDMA/100
sdh1
sd 6:0:0:0: [sdh] Attached SCSI disk
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 24 (level, low) -> IRQ 21
scsi11 : sata_promise
scsi12 : sata_promise
scsi13 : sata_promise
scsi14 : sata_promise
ata11: PATA max UDMA/133 cmd 0xf883a200 ctl 0xf883a238 bmdma
0x00000000 irq 21
ata12: PATA max UDMA/133 cmd 0xf883a280 ctl 0xf883a2b8 bmdma
0x00000000 irq 21
ata13: PATA max UDMA/133 cmd 0xf883a300 ctl 0xf883a338 bmdma
0x00000000 irq 21
ata14: PATA max UDMA/133 cmd 0xf883a380 ctl 0xf883a3b8 bmdma
0x00000000 irq 21
ata10.01: ATA-6: WDC WD2000BB-22GUA0, 08.02D08, max UDMA/100
ata10.01: 390721968 sectors, multi 16: LBA48
ata11.00: ATA-6: HDS722525VLAT80, V36OA6MA, max UDMA/100
ata11.00: 488397168 sectors, multi 0: LBA48
ata10.01: configured for UDMA/100
scsi 9:0:1:0: Direct-Access ATA WDC WD2000BB-22G 08.0 PQ: 0
ANSI: 5
sd 9:0:1:0: [sdi] 390721968 512-byte hardware sectors (200050 MB)
sd 9:0:1:0: [sdi] Write Protect is off
sd 9:0:1:0: [sdi] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 9:0:1:0: [sdi] 390721968 512-byte hardware sectors (200050 MB)
sd 9:0:1:0: [sdi] Write Protect is off
sd 9:0:1:0: [sdi] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdi: sdi1 sdi2
sd 9:0:1:0: [sdi] Attached SCSI disk
scsi 10:0:1:0: Direct-Access ATA WDC WD2000BB-22G 08.0 PQ: 0
ANSI: 5
sd 10:0:1:0: [sdj] 390721968 512-byte hardware sectors (200050 MB)
sd 10:0:1:0: [sdj] Write Protect is off
sd 10:0:1:0: [sdj] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 10:0:1:0: [sdj] 390721968 512-byte hardware sectors (200050 MB)
sd 10:0:1:0: [sdj] Write Protect is off
sd 10:0:1:0: [sdj] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdj:<6>ata11.00: configured for UDMA/100
sdj1 sdj2
sd 10:0:1:0: [sdj] Attached SCSI disk
ata12.00: ATA-6: HDS722525VLAT80, V36OA6MA, max UDMA/100
ata12.00: 488397168 sectors, multi 0: LBA48
ata12.00: configured for UDMA/100
ata13.00: ATA-6: HDS722525VLAT80, V36OA6MA, max UDMA/100
ata13.00: 488397168 sectors, multi 0: LBA48
ata13.00: configured for UDMA/100
ata14.00: ATA-6: HDS722525VLAT80, V36OA6MA, max UDMA/100
ata14.00: 488397168 sectors, multi 0: LBA48
ata14.00: configured for UDMA/100
scsi 11:0:0:0: Direct-Access ATA HDS722525VLAT80 V36O PQ: 0
ANSI: 5
sd 11:0:0:0: [sdk] 488397168 512-byte hardware sectors (250059 MB)
sd 11:0:0:0: [sdk] Write Protect is off
sd 11:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 11:0:0:0: [sdk] 488397168 512-byte hardware sectors (250059 MB)
sd 11:0:0:0: [sdk] Write Protect is off
sd 11:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdk: unknown partition table
sd 11:0:0:0: [sdk] Attached SCSI disk
scsi 12:0:0:0: Direct-Access ATA HDS722525VLAT80 V36O PQ: 0
ANSI: 5
sd 12:0:0:0: [sdl] 488397168 512-byte hardware sectors (250059 MB)
sd 12:0:0:0: [sdl] Write Protect is off
sd 12:0:0:0: [sdl] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 12:0:0:0: [sdl] 488397168 512-byte hardware sectors (250059 MB)
sd 12:0:0:0: [sdl] Write Protect is off
sd 12:0:0:0: [sdl] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdl: unknown partition table
sd 12:0:0:0: [sdl] Attached SCSI disk
scsi 13:0:0:0: Direct-Access ATA HDS722525VLAT80 V36O PQ: 0
ANSI: 5
sd 13:0:0:0: [sdm] 488397168 512-byte hardware sectors (250059 MB)
sd 13:0:0:0: [sdm] Write Protect is off
sd 13:0:0:0: [sdm] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 13:0:0:0: [sdm] 488397168 512-byte hardware sectors (250059 MB)
sd 13:0:0:0: [sdm] Write Protect is off
sd 13:0:0:0: [sdm] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdm: unknown partition table
sd 13:0:0:0: [sdm] Attached SCSI disk
scsi 14:0:0:0: Direct-Access ATA HDS722525VLAT80 V36O PQ: 0
ANSI: 5
sd 14:0:0:0: [sdn] 488397168 512-byte hardware sectors (250059 MB)
sd 14:0:0:0: [sdn] Write Protect is off
sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 14:0:0:0: [sdn] 488397168 512-byte hardware sectors (250059 MB)
sd 14:0:0:0: [sdn] Write Protect is off
sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdn: unknown partition table
sd 14:0:0:0: [sdn] Attached SCSI disk
md: raid1 personality registered for level 1
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 3617.000 MB/sec
raid5: using function: pIII_sse (3617.000 MB/sec)
raid6: int32x1 857 MB/s
raid6: int32x2 860 MB/s
raid6: int32x4 732 MB/s
raid6: int32x8 519 MB/s
raid6: mmxx1 2247 MB/s
raid6: mmxx2 2453 MB/s
raid6: sse1x1 1160 MB/s
raid6: sse1x2 1960 MB/s
raid6: sse2x1 2083 MB/s
raid6: sse2x2 2832 MB/s
raid6: using algorithm sse2x2 (2832 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: md2 stopped.
md: bind<sdk>
md: bind<sdn>
md: bind<sdl>
md: bind<sdm>
raid5: device sdm operational as raid disk 0
raid5: device sdl operational as raid disk 3
raid5: device sdn operational as raid disk 2
raid5: device sdk operational as raid disk 1
raid5: allocated 4204kB for md2
raid5: raid level 5 set md2 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
--- rd:4 wd:4
disk 0, o:1, dev:sdm
disk 1, o:1, dev:sdk
disk 2, o:1, dev:sdn
disk 3, o:1, dev:sdl
md: md1 stopped.
md: bind<sdh1>
md: bind<sdg1>
md: bind<sde1>
md: bind<sdj1>
md: bind<sdi1>
md: bind<sdc1>
md: bind<sdd1>
md: bind<sdf1>
raid5: device sdf1 operational as raid disk 0
raid5: device sdc1 operational as raid disk 7
raid5: device sdi1 operational as raid disk 5
raid5: device sdj1 operational as raid disk 4
raid5: device sde1 operational as raid disk 3
raid5: device sdg1 operational as raid disk 2
raid5: device sdh1 operational as raid disk 1
raid5: allocated 8368kB for md1
RAID5 conf printout:
--- rd:8 wd:7
disk 0, o:1, dev:sdf1
disk 1, o:1, dev:sdh1
disk 2, o:1, dev:sdg1
disk 3, o:1, dev:sde1
disk 4, o:1, dev:sdj1
disk 5, o:1, dev:sdi1
disk 7, o:1, dev:sdc1
RAID5 conf printout:
--- rd:8 wd:7
disk 0, o:1, dev:sdf1
disk 1, o:1, dev:sdh1
disk 2, o:1, dev:sdg1
disk 3, o:1, dev:sde1
disk 4, o:1, dev:sdj1
disk 5, o:1, dev:sdi1
disk 6, o:1, dev:sdd1
disk 7, o:1, dev:sdc1
md: recovery of RAID array md1
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than
200000 KB/sec) for recovery.
md: using 128k window, over a total of 180939968 blocks.
md: md0 stopped.
md: bind<sdb1>
md: bind<sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input1
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 1
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
Linux agpgart interface v0.102 (c) Dave Jones
Real Time Clock Driver v1.12ac
piix4_smbus 0000:00:0f.0: Found 0000:00:0f.0 device
FDC 0 is a National Semiconductor PC87306
EXT3 FS on md0, internal journal
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_tables: (C) 2000-2006 Netfilter Core Team
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex,
Flow Control: RX/TX
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
reply other threads:[~2007-08-13 15:37 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=46C07241.7010605@fjordn.net \
--to=ole@fjordn.net \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).