* Still having problems with sata_promise on all late kernels
@ 2007-08-14 3:04 Brad Campbell
2007-08-14 4:37 ` Still having problems with sata_promise on all late kernels - shutdown too Brad Campbell
2007-08-14 10:20 ` Still having problems with sata_promise on all late kernels Tejun Heo
0 siblings, 2 replies; 15+ messages in thread
From: Brad Campbell @ 2007-08-14 3:04 UTC (permalink / raw)
To: linux-ide
G'day all,
This has been happening on a lightly loaded box for a while now. I have posted about it before.
The issue is now I've upgraded 3 drives from 250GB Maxtors to 750GB WD's, it's just getting worse,
particularly when the drives are loaded. I've jumpered the WD's to 1.5GB PHY speed (I had to do that
or the on-board via sata controller would not recognise one of the drives.
The box is a bit of a mish-mash of controllers. I have 3 Promise SATA150TX4, one SIL3112 (all on PCI
cards) and the on-board 2 port VIA driver.
I'm at a bit of a loss as to what to do really, short of replacing the Promise cards with something
else.
brad@srv:~$ dmesg | grep "hard resetting port" | wc -l
990
brad@srv:~$ uptime
06:55:04 up 8:14, 9 users, load average: 5.21, 5.27, 4.92
brad@srv:~$ uname -a
Linux srv 2.6.23-rc3 #3 Mon Aug 13 11:20:23 GST 2007 i686 GNU/Linux
brad@srv:~$ lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge (rev 80)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
00:09.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T [Marvell] (rev 12)
00:0b.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
00:0c.0 Mass storage controller: Silicon Image, Inc. SiI 3112 [SATALink/SATARaid] Serial ATA
Controller (rev 02)
00:0d.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 12)
00:0e.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master
IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller
(rev 60)
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
00:13.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 315PRO PCI/AGP VGA Display Adapter
brad@srv:~$ cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 10
model name : AMD Athlon(TM) XP 2600+
stepping : 0
cpu MHz : 1916.544
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr
sse syscall mmxext 3dnowext 3dnow ts
bogomips : 3835.54
clflush size : 32
brad@srv:~$ cat /proc/interrupts
CPU0
0: 71848 IO-APIC-edge timer
1: 17 IO-APIC-edge i8042
4: 62 IO-APIC-edge serial
8: 3 IO-APIC-edge rtc
9: 0 IO-APIC-fasteoi acpi
16: 1323517 IO-APIC-fasteoi sata_sil, sata_promise
17: 211665 IO-APIC-fasteoi sata_via
18: 272230 IO-APIC-fasteoi sata_promise
19: 4770431 IO-APIC-fasteoi sata_promise, eth0
20: 7353914 IO-APIC-fasteoi eth1
21: 4038815 IO-APIC-fasteoi uhci_hcd:usb1, uhci_hcd:usb2, uhci_hcd:usb3, uhci_hcd:usb4,
ehci_hcd:usb5
NMI: 0
LOC: 9811571
ERR: 0
MIS: 0
brad@srv:~$ cat /proc/mdstat
Personalities : [raid0] [raid1] [raid6] [raid5] [raid4]
md2 : active raid5 sdo[0] sdb[3] sdn[2]
1465148928 blocks level 5, 128k chunk, algorithm 2 [3/2] [U_U]
[===========>.........] recovery = 55.8% (409462104/732574464) finish=383.5min speed=14041K/sec
md0 : active raid5 sdd1[0] sdm1[9] sdl1[8] sdk1[7] sdj1[6] sdi1[5] sdh1[4] sdg1[3] sdf1[2] sde1[1]
2206003968 blocks level 5, 128k chunk, algorithm 0 [10/10] [UUUUUUUUUU]
md5 : active raid1 sdc4[0] sda4[1]
200217984 blocks [2/2] [UU]
md4 : active raid1 sdc3[0] sda3[1]
4891712 blocks [2/2] [UU]
md3 : active raid1 sdc2[0] sda2[1]
19542976 blocks [2/2] [UU]
md1 : active raid1 sdc1[0] sda1[1]
19542976 blocks [2/2] [UU]
unused devices: <none>
[ 28.626959] Freeing unused kernel memory: 192k freed
[ 28.685039] sata_sil 0000:00:0c.0: version 2.2
[ 28.685118] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 19 (level, low) -> IRQ 16
[ 28.685361] scsi0 : sata_sil
[ 28.685466] scsi1 : sata_sil
[ 28.685545] ata1: SATA max UDMA/100 cmd 0xf881e080 ctl 0xf881e08a bmdma 0xf881e000 irq 16
[ 28.685596] ata2: SATA max UDMA/100 cmd 0xf881e0c0 ctl 0xf881e0ca bmdma 0xf881e008 irq 16
[ 29.165502] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 29.185927] ata1.00: ATA-7: Maxtor 7Y250M0, YAR51HW0, max UDMA/133
[ 29.185968] ata1.00: 490234752 sectors, multi 16: LBA48
[ 29.225879] ata1.00: configured for UDMA/100
[ 29.715175] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 29.742761] ata2.00: ATA-7: WDC WD7500AAKS-00RBA0, 30.04G30, max UDMA/133
[ 29.742803] ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 29.776035] ata2.00: configured for UDMA/100
[ 29.776181] scsi 0:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 29.776333] sd 0:0:0:0: [sda] 490234752 512-byte hardware sectors (251000 MB)
[ 29.776387] sd 0:0:0:0: [sda] Write Protect is off
[ 29.776427] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 29.776444] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 29.776540] sd 0:0:0:0: [sda] 490234752 512-byte hardware sectors (251000 MB)
[ 29.776589] sd 0:0:0:0: [sda] Write Protect is off
[ 29.776629] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 29.776643] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 29.776694] sda: sda1 sda2 sda3 sda4
[ 29.790518] sd 0:0:0:0: [sda] Attached SCSI disk
[ 29.790620] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 29.790727] scsi 1:0:0:0: Direct-Access ATA WDC WD7500AAKS-0 30.0 PQ: 0 ANSI: 5
[ 29.790855] sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
[ 29.790911] sd 1:0:0:0: [sdb] Write Protect is off
[ 29.790950] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 29.790965] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 29.791053] sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
[ 29.791108] sd 1:0:0:0: [sdb] Write Protect is off
[ 29.791147] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 29.791161] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 29.791212] sdb: unknown partition table
[ 29.800633] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 29.800732] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 29.806178] sata_via 0000:00:0f.0: version 2.2
[ 29.806224] ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 17
[ 29.806376] sata_via 0000:00:0f.0: routed to hard irq line 0
[ 29.806472] scsi2 : sata_via
[ 29.806580] scsi3 : sata_via
[ 29.806667] ata3: SATA max UDMA/133 cmd 0x00017400 ctl 0x00017002 bmdma 0x00016000 irq 17
[ 29.806718] ata4: SATA max UDMA/133 cmd 0x00016800 ctl 0x00016402 bmdma 0x00016008 irq 17
[ 30.014986] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 30.215202] ata3.00: ATA-7: Maxtor 7Y250M0, YAR51HW0, max UDMA/133
[ 30.215243] ata3.00: 490234752 sectors, multi 0: LBA48
[ 30.255162] ata3.00: configured for UDMA/133
[ 30.464719] ata4: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 30.475365] scsi 2:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 30.475510] sd 2:0:0:0: [sdc] 490234752 512-byte hardware sectors (251000 MB)
[ 30.475563] sd 2:0:0:0: [sdc] Write Protect is off
[ 30.475603] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 30.475619] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.475715] sd 2:0:0:0: [sdc] 490234752 512-byte hardware sectors (251000 MB)
[ 30.475763] sd 2:0:0:0: [sdc] Write Protect is off
[ 30.475803] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 30.475816] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.475868] sdc: sdc1 sdc2 sdc3 sdc4
[ 30.483558] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 30.483662] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 30.488904] sata_promise 0000:00:0b.0: version 2.09
[ 30.488930] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 16
[ 30.504787] scsi4 : sata_promise
[ 30.504903] scsi5 : sata_promise
[ 30.504992] scsi6 : sata_promise
[ 30.505081] scsi7 : sata_promise
[ 30.505172] ata5: SATA max UDMA/133 cmd 0xf882c200 ctl 0xf882c238 bmdma 0x00000000 irq 16
[ 30.505223] ata6: SATA max UDMA/133 cmd 0xf882c280 ctl 0xf882c2b8 bmdma 0x00000000 irq 16
[ 30.505274] ata7: SATA max UDMA/133 cmd 0xf882c300 ctl 0xf882c338 bmdma 0x00000000 irq 16
[ 30.505324] ata8: SATA max UDMA/133 cmd 0xf882c380 ctl 0xf882c3b8 bmdma 0x00000000 irq 16
[ 30.994427] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 31.014865] ata5.00: ATA-7: Maxtor 7Y250M0, YAR51EW0, max UDMA/133
[ 31.014906] ata5.00: 490234752 sectors, multi 0: LBA48
[ 31.054821] ata5.00: configured for UDMA/133
[ 31.544099] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 31.564540] ata6.00: ATA-7: Maxtor 7Y250M0, YAR51EW0, max UDMA/133
[ 31.564581] ata6.00: 490234752 sectors, multi 0: LBA48
[ 31.604496] ata6.00: configured for UDMA/133
[ 32.093775] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 32.114196] ata7.00: ATA-7: Maxtor 7Y250M0, YAR51EW0, max UDMA/133
[ 32.114237] ata7.00: 490234752 sectors, multi 0: LBA48
[ 32.154173] ata7.00: configured for UDMA/133
[ 32.643450] ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 32.663870] ata8.00: ATA-7: Maxtor 7Y250M0, YAR51EW0, max UDMA/133
[ 32.663911] ata8.00: 490234752 sectors, multi 0: LBA48
[ 32.703859] ata8.00: configured for UDMA/133
[ 32.704007] scsi 4:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 32.704153] sd 4:0:0:0: [sdd] 490234752 512-byte hardware sectors (251000 MB)
[ 32.704207] sd 4:0:0:0: [sdd] Write Protect is off
[ 32.704247] sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 32.704264] sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.704367] sd 4:0:0:0: [sdd] 490234752 512-byte hardware sectors (251000 MB)
[ 32.704416] sd 4:0:0:0: [sdd] Write Protect is off
[ 32.704456] sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 32.704471] sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.704522] sdd: sdd1
[ 32.721933] sd 4:0:0:0: [sdd] Attached SCSI disk
[ 32.722035] sd 4:0:0:0: Attached scsi generic sg3 type 0
[ 32.722135] scsi 5:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 32.722270] sd 5:0:0:0: [sde] 490234752 512-byte hardware sectors (251000 MB)
[ 32.722320] sd 5:0:0:0: [sde] Write Protect is off
[ 32.722359] sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 32.722374] sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.722452] sd 5:0:0:0: [sde] 490234752 512-byte hardware sectors (251000 MB)
[ 32.722501] sd 5:0:0:0: [sde] Write Protect is off
[ 32.722541] sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 32.722555] sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.722605] sde: sde1
[ 32.741783] sd 5:0:0:0: [sde] Attached SCSI disk
[ 32.741880] sd 5:0:0:0: Attached scsi generic sg4 type 0
[ 32.741977] scsi 6:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 32.742111] sd 6:0:0:0: [sdf] 490234752 512-byte hardware sectors (251000 MB)
[ 32.742160] sd 6:0:0:0: [sdf] Write Protect is off
[ 32.742200] sd 6:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 32.742214] sd 6:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.742290] sd 6:0:0:0: [sdf] 490234752 512-byte hardware sectors (251000 MB)
[ 32.742339] sd 6:0:0:0: [sdf] Write Protect is off
[ 32.742378] sd 6:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 32.742392] sd 6:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.742443] sdf: sdf1
[ 32.787559] sd 6:0:0:0: [sdf] Attached SCSI disk
[ 32.787655] sd 6:0:0:0: Attached scsi generic sg5 type 0
[ 32.787757] scsi 7:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 32.787879] sd 7:0:0:0: [sdg] 490234752 512-byte hardware sectors (251000 MB)
[ 32.787929] sd 7:0:0:0: [sdg] Write Protect is off
[ 32.787969] sd 7:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 32.787983] sd 7:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.788060] sd 7:0:0:0: [sdg] 490234752 512-byte hardware sectors (251000 MB)
[ 32.788109] sd 7:0:0:0: [sdg] Write Protect is off
[ 32.788148] sd 7:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 32.788163] sd 7:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.788213] sdg: sdg1
[ 32.812064] sd 7:0:0:0: [sdg] Attached SCSI disk
[ 32.812157] sd 7:0:0:0: Attached scsi generic sg6 type 0
[ 32.812993] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 18
[ 32.823377] scsi8 : sata_promise
[ 32.823466] scsi9 : sata_promise
[ 32.823549] scsi10 : sata_promise
[ 32.823635] scsi11 : sata_promise
[ 32.823718] ata9: SATA max UDMA/133 cmd 0xf882e200 ctl 0xf882e238 bmdma 0x00000000 irq 18
[ 32.823769] ata10: SATA max UDMA/133 cmd 0xf882e280 ctl 0xf882e2b8 bmdma 0x00000000 irq 18
[ 32.823819] ata11: SATA max UDMA/133 cmd 0xf882e300 ctl 0xf882e338 bmdma 0x00000000 irq 18
[ 32.823869] ata12: SATA max UDMA/133 cmd 0xf882e380 ctl 0xf882e3b8 bmdma 0x00000000 irq 18
[ 33.313055] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 33.333475] ata9.00: ATA-7: Maxtor 7Y250M0, YAR51EW0, max UDMA/133
[ 33.333517] ata9.00: 490234752 sectors, multi 0: LBA48
[ 33.373459] ata9.00: configured for UDMA/133
[ 33.862730] ata10: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 33.883156] ata10.00: ATA-7: Maxtor 7Y250M0, YAR51EW0, max UDMA/133
[ 33.883197] ata10.00: 490234752 sectors, multi 0: LBA48
[ 33.923143] ata10.00: configured for UDMA/133
[ 34.412405] ata11: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 34.432835] ata11.00: ATA-7: Maxtor 7Y250M0, YAR51EW0, max UDMA/133
[ 34.432876] ata11.00: 490234752 sectors, multi 0: LBA48
[ 34.472799] ata11.00: configured for UDMA/133
[ 34.962080] ata12: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 34.982499] ata12.00: ATA-7: Maxtor 7Y250M0, YAR51EW0, max UDMA/133
[ 34.982540] ata12.00: 490234752 sectors, multi 0: LBA48
[ 35.022488] ata12.00: configured for UDMA/133
[ 35.022581] scsi 8:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 35.022713] sd 8:0:0:0: [sdh] 490234752 512-byte hardware sectors (251000 MB)
[ 35.022763] sd 8:0:0:0: [sdh] Write Protect is off
[ 35.022802] sd 8:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 35.022817] sd 8:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 35.022897] sd 8:0:0:0: [sdh] 490234752 512-byte hardware sectors (251000 MB)
[ 35.022946] sd 8:0:0:0: [sdh] Write Protect is off
[ 35.022985] sd 8:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 35.023000] sd 8:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 35.023051] sdh: sdh1
[ 35.042161] sd 8:0:0:0: [sdh] Attached SCSI disk
[ 35.042259] sd 8:0:0:0: Attached scsi generic sg7 type 0
[ 35.042364] scsi 9:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 35.042494] sd 9:0:0:0: [sdi] 490234752 512-byte hardware sectors (251000 MB)
[ 35.042544] sd 9:0:0:0: [sdi] Write Protect is off
[ 35.042584] sd 9:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[ 35.042598] sd 9:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 35.042676] sd 9:0:0:0: [sdi] 490234752 512-byte hardware sectors (251000 MB)
[ 35.042725] sd 9:0:0:0: [sdi] Write Protect is off
[ 35.042764] sd 9:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[ 35.042778] sd 9:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 35.042829] sdi: sdi1
[ 35.061735] sd 9:0:0:0: [sdi] Attached SCSI disk
[ 35.061842] sd 9:0:0:0: Attached scsi generic sg8 type 0
[ 35.061937] scsi 10:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 35.062073] sd 10:0:0:0: [sdj] 490234752 512-byte hardware sectors (251000 MB)
[ 35.062129] sd 10:0:0:0: [sdj] Write Protect is off
[ 35.062169] sd 10:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 35.062183] sd 10:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 35.062271] sd 10:0:0:0: [sdj] 490234752 512-byte hardware sectors (251000 MB)
[ 35.062326] sd 10:0:0:0: [sdj] Write Protect is off
[ 35.062365] sd 10:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 35.062379] sd 10:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 35.062430] sdj: sdj1
[ 35.083112] sd 10:0:0:0: [sdj] Attached SCSI disk
[ 35.083216] sd 10:0:0:0: Attached scsi generic sg9 type 0
[ 35.083312] scsi 11:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 35.083437] sd 11:0:0:0: [sdk] 490234752 512-byte hardware sectors (251000 MB)
[ 35.083492] sd 11:0:0:0: [sdk] Write Protect is off
[ 35.083532] sd 11:0:0:0: [sdk] Mode Sense: 00 3a 00 00
[ 35.083546] sd 11:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 35.083623] sd 11:0:0:0: [sdk] 490234752 512-byte hardware sectors (251000 MB)
[ 35.083678] sd 11:0:0:0: [sdk] Write Protect is off
[ 35.083718] sd 11:0:0:0: [sdk] Mode Sense: 00 3a 00 00
[ 35.083732] sd 11:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 35.083783] sdk: sdk1
[ 35.102151] sd 11:0:0:0: [sdk] Attached SCSI disk
[ 35.102247] sd 11:0:0:0: Attached scsi generic sg10 type 0
[ 35.102328] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 19
[ 35.122021] scsi12 : sata_promise
[ 35.122118] scsi13 : sata_promise
[ 35.122202] scsi14 : sata_promise
[ 35.122293] scsi15 : sata_promise
[ 35.122370] ata13: SATA max UDMA/133 cmd 0xf8830200 ctl 0xf8830238 bmdma 0x00000000 irq 19
[ 35.122421] ata14: SATA max UDMA/133 cmd 0xf8830280 ctl 0xf88302b8 bmdma 0x00000000 irq 19
[ 35.122472] ata15: SATA max UDMA/133 cmd 0xf8830300 ctl 0xf8830338 bmdma 0x00000000 irq 19
[ 35.122522] ata16: SATA max UDMA/133 cmd 0xf8830380 ctl 0xf88303b8 bmdma 0x00000000 irq 19
[ 35.611701] ata13: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 35.632191] ata13.00: ATA-7: Maxtor 7Y250M0, YAR51EW0, max UDMA/133
[ 35.632233] ata13.00: 490234752 sectors, multi 0: LBA48
[ 35.672183] ata13.00: configured for UDMA/133
[ 36.161376] ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 36.181863] ata14.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 36.181904] ata14.00: 490234752 sectors, multi 0: LBA48
[ 36.221848] ata14.00: configured for UDMA/133
[ 36.711051] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 36.731024] Switched to high resolution mode on CPU 0
[ 36.740905] ata15.00: ATA-7: WDC WD7500AAKS-00RBA0, 30.04G30, max UDMA/133
[ 36.740946] ata15.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 36.771967] ata15.00: configured for UDMA/133
[ 37.260977] ata16: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 37.291678] ata16.00: ATA-7: WDC WD7500AAKS-00RBA0, 30.04G30, max UDMA/133
[ 37.291720] ata16.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 37.331930] ata16.00: configured for UDMA/133
[ 37.332018] scsi 12:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 37.332145] sd 12:0:0:0: [sdl] 490234752 512-byte hardware sectors (251000 MB)
[ 37.332201] sd 12:0:0:0: [sdl] Write Protect is off
[ 37.332240] sd 12:0:0:0: [sdl] Mode Sense: 00 3a 00 00
[ 37.332255] sd 12:0:0:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.332335] sd 12:0:0:0: [sdl] 490234752 512-byte hardware sectors (251000 MB)
[ 37.332390] sd 12:0:0:0: [sdl] Write Protect is off
[ 37.332430] sd 12:0:0:0: [sdl] Mode Sense: 00 3a 00 00
[ 37.332444] sd 12:0:0:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.332495] sdl: sdl1
[ 37.355681] sd 12:0:0:0: [sdl] Attached SCSI disk
[ 37.355776] sd 12:0:0:0: Attached scsi generic sg11 type 0
[ 37.355874] scsi 13:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 37.356000] sd 13:0:0:0: [sdm] 490234752 512-byte hardware sectors (251000 MB)
[ 37.356056] sd 13:0:0:0: [sdm] Write Protect is off
[ 37.356096] sd 13:0:0:0: [sdm] Mode Sense: 00 3a 00 00
[ 37.356110] sd 13:0:0:0: [sdm] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.356187] sd 13:0:0:0: [sdm] 490234752 512-byte hardware sectors (251000 MB)
[ 37.356242] sd 13:0:0:0: [sdm] Write Protect is off
[ 37.356282] sd 13:0:0:0: [sdm] Mode Sense: 00 3a 00 00
[ 37.356296] sd 13:0:0:0: [sdm] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.356347] sdm: sdm1
[ 37.366978] sd 13:0:0:0: [sdm] Attached SCSI disk
[ 37.367080] sd 13:0:0:0: Attached scsi generic sg12 type 0
[ 37.367176] scsi 14:0:0:0: Direct-Access ATA WDC WD7500AAKS-0 30.0 PQ: 0 ANSI: 5
[ 37.367303] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[ 37.367359] sd 14:0:0:0: [sdn] Write Protect is off
[ 37.367399] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[ 37.367413] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.367498] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[ 37.368305] sd 14:0:0:0: [sdn] Write Protect is off
[ 37.368345] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[ 37.368359] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.368409] sdn: unknown partition table
[ 37.371026] sd 14:0:0:0: [sdn] Attached SCSI disk
[ 37.371129] sd 14:0:0:0: Attached scsi generic sg13 type 0
[ 37.371225] scsi 15:0:0:0: Direct-Access ATA WDC WD7500AAKS-0 30.0 PQ: 0 ANSI: 5
[ 37.371355] sd 15:0:0:0: [sdo] 1465149168 512-byte hardware sectors (750156 MB)
[ 37.371411] sd 15:0:0:0: [sdo] Write Protect is off
[ 37.371450] sd 15:0:0:0: [sdo] Mode Sense: 00 3a 00 00
[ 37.371465] sd 15:0:0:0: [sdo] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.371550] sd 15:0:0:0: [sdo] 1465149168 512-byte hardware sectors (750156 MB)
[ 37.371606] sd 15:0:0:0: [sdo] Write Protect is off
[ 37.371645] sd 15:0:0:0: [sdo] Mode Sense: 00 3a 00 00
[ 37.371659] sd 15:0:0:0: [sdo] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.371710] sdo: unknown partition table
[ 37.374420] sd 15:0:0:0: [sdo] Attached SCSI disk
[ 37.374523] sd 15:0:0:0: Attached scsi generic sg14 type 0
<snip lots and lots of errors>
[28709.825489] ata15: hard resetting port
[28710.327227] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[28710.378398] ata15.00: configured for UDMA/33
[28710.378441] ata15: EH complete
[28710.460556] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[28710.499998] sd 14:0:0:0: [sdn] Write Protect is off
[28710.500028] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[28710.562799] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28741.832705] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[28741.832733] ata15.00: port_status 0x20200000
[28741.832751] ata15.00: cmd 25/00:00:00:b1:54/00:04:2f:00:00/e0 tag 0 cdb 0x0 data 524288 in
[28741.832753] res 51/0c:5f:a1:b1:54/0c:03:2f:00:00/e0 Emask 0x10 (ATA bus error)
[28741.832806] ata15: hard resetting port
[28742.358261] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[28742.413120] ata15.00: configured for UDMA/33
[28742.413163] ata15: EH complete
[28742.487607] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[28742.526602] sd 14:0:0:0: [sdn] Write Protect is off
[28742.526631] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[28742.591078] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28795.033648] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[28795.033675] ata15.00: port_status 0x20200000
[28795.033693] ata15.00: cmd 25/00:00:00:85:6b/00:04:2f:00:00/e0 tag 0 cdb 0x0 data 524288 in
[28795.033695] res 51/0c:2f:d1:85:6b/0c:03:2f:00:00/e0 Emask 0x10 (ATA bus error)
[28795.033747] ata15: hard resetting port
[28795.536735] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[28795.617197] ata15.00: configured for UDMA/33
[28795.617241] ata15: EH complete
[28795.703828] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[28795.752159] sd 14:0:0:0: [sdn] Write Protect is off
[28795.752190] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[28795.803082] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28940.313319] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[28940.313347] ata15.00: port_status 0x20200000
[28940.313365] ata15.00: cmd 25/00:00:a0:57:a0/00:04:2f:00:00/e0 tag 0 cdb 0x0 data 524288 in
[28940.313367] res 51/0c:5f:41:5a:a0/0c:01:2f:00:00/e0 Emask 0x10 (ATA bus error)
[28940.313423] ata15: hard resetting port
[28940.821227] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[28940.881930] ata15.00: configured for UDMA/33
[28940.881973] ata15: EH complete
[28940.960533] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[28940.968408] sd 14:0:0:0: [sdn] Write Protect is off
[28940.968427] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[28940.979329] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29193.654162] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29193.654193] ata15.00: port_status 0x20200000
[29193.654211] ata15.00: cmd 25/00:00:00:db:ec/00:04:2f:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29193.654213] res 51/0c:2f:d1:db:ec/0c:03:2f:00:00/e0 Emask 0x10 (ATA bus error)
[29193.654271] ata15: hard resetting port
[29194.160468] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29194.241583] ata15.00: configured for UDMA/33
[29194.241627] ata15: EH complete
[29194.410207] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29194.410746] sd 14:0:0:0: [sdn] Write Protect is off
[29194.410763] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29194.495828] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29195.659632] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29195.659659] ata15.00: port_status 0x20200000
[29195.659677] ata15.00: cmd 25/00:00:00:4b:ed/00:04:2f:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29195.659679] res 51/0c:bf:41:4d:ed/0c:01:2f:00:00/e0 Emask 0x10 (ATA bus error)
[29195.659732] ata15: hard resetting port
[29196.159157] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29196.240367] ata15.00: configured for UDMA/33
[29196.240410] ata15: EH complete
[29196.311812] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29196.312786] sd 14:0:0:0: [sdn] Write Protect is off
[29196.312805] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29196.327517] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29203.938497] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29203.938524] ata15.00: port_status 0x20200000
[29203.938542] ata15.00: cmd 25/00:00:b0:ea:ef/00:04:2f:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29203.938545] res 51/0c:7f:31:eb:ef/0c:03:2f:00:00/e0 Emask 0x10 (ATA bus error)
[29203.938598] ata15: hard resetting port
[29204.524234] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29204.595683] ata15.00: configured for UDMA/33
[29204.595726] ata15: EH complete
[29204.677730] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29204.718810] sd 14:0:0:0: [sdn] Write Protect is off
[29204.718841] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29204.781863] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29209.243050] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29209.243078] ata15.00: port_status 0x20200000
[29209.243096] ata15.00: cmd 25/00:00:d0:56:f1/00:04:2f:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29209.243098] res 51/0c:0f:c1:57:f1/0c:03:2f:00:00/e0 Emask 0x10 (ATA bus error)
[29209.243151] ata15: hard resetting port
[29209.801099] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29209.882794] ata15.00: configured for UDMA/33
[29209.882836] ata15: EH complete
[29209.968689] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29209.983562] sd 14:0:0:0: [sdn] Write Protect is off
[29209.983592] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29209.987341] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29264.619705] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29264.619734] ata15.00: port_status 0x20200000
[29264.619752] ata15.00: cmd 25/00:00:00:1b:02/00:04:30:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29264.619754] res 51/0c:00:ff:1e:02/0c:00:30:00:00/e0 Emask 0x10 (ATA bus error)
[29264.619808] ata15: hard resetting port
[29265.199696] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29265.248788] ata15.00: configured for UDMA/33
[29265.248832] ata15: EH complete
[29265.328952] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29265.369406] sd 14:0:0:0: [sdn] Write Protect is off
[29265.369436] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29265.432610] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29309.946702] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29309.946730] ata15.00: port_status 0x20200000
[29309.946748] ata15.00: cmd 25/00:00:00:6b:15/00:04:30:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29309.946750] res 51/0c:9f:61:6e:15/0c:00:30:00:00/e0 Emask 0x10 (ATA bus error)
[29309.946811] ata15: hard resetting port
[29310.491333] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29310.572766] ata15.00: configured for UDMA/33
[29310.572808] ata15: EH complete
[29310.655530] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29310.695178] sd 14:0:0:0: [sdn] Write Protect is off
[29310.695208] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29310.763870] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29312.542555] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29312.542582] ata15.00: port_status 0x20200000
[29312.542600] ata15.00: cmd 25/00:00:00:47:16/00:04:30:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29312.542602] res 51/0c:ff:01:48:16/0c:02:30:00:00/e0 Emask 0x10 (ATA bus error)
[29312.542655] ata15: hard resetting port
[29313.049971] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29313.100785] ata15.00: configured for UDMA/33
[29313.100820] ata15: EH complete
[29313.248726] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29313.319242] sd 14:0:0:0: [sdn] Write Protect is off
[29313.319272] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29313.389715] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29317.568100] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29317.568128] ata15.00: port_status 0x20200000
[29317.568146] ata15.00: cmd 25/00:00:30:4d:18/00:04:30:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29317.568148] res 51/0c:7f:b1:4e:18/0c:02:30:00:00/e0 Emask 0x10 (ATA bus error)
[29317.568201] ata15: hard resetting port
[29318.077123] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29318.137807] ata15.00: configured for UDMA/33
[29318.137850] ata15: EH complete
[29318.216414] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29318.256434] sd 14:0:0:0: [sdn] Write Protect is off
[29318.256491] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29318.394857] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29470.310985] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29470.311012] ata15.00: port_status 0x20200000
[29470.311030] ata15.00: cmd 25/00:00:00:ea:56/00:04:30:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29470.311032] res 51/0c:7f:81:ea:56/0c:03:30:00:00/e0 Emask 0x10 (ATA bus error)
[29470.311085] ata15: hard resetting port
[29470.816829] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29470.897960] ata15.00: configured for UDMA/33
[29470.898034] ata15: EH complete
[29470.980584] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29471.022850] sd 14:0:0:0: [sdn] Write Protect is off
[29471.022879] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29471.086914] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29506.727933] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29506.727961] ata15.00: port_status 0x20200000
[29506.727979] ata15.00: cmd 25/00:00:00:71:64/00:04:30:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29506.727981] res 51/0c:4f:b1:72:64/0c:02:30:00:00/e0 Emask 0x10 (ATA bus error)
[29506.728034] ata15: hard resetting port
[29507.234647] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29507.296034] ata15.00: configured for UDMA/33
[29507.296071] ata15: EH complete
[29507.373399] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29507.545398] sd 14:0:0:0: [sdn] Write Protect is off
[29507.545430] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29507.622395] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29555.709386] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29555.709414] ata15.00: port_status 0x20200000
[29555.709432] ata15.00: cmd 25/00:00:00:bd:75/00:04:30:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29555.709434] res 51/0c:ef:11:c0:75/0c:00:30:00:00/e0 Emask 0x10 (ATA bus error)
[29555.709488] ata15: hard resetting port
[29556.235991] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29556.306323] ata15.00: configured for UDMA/33
[29556.306360] ata15: EH complete
[29556.378394] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29556.549202] sd 14:0:0:0: [sdn] Write Protect is off
[29556.549232] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29556.609265] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[29559.807528] ata15.00: exception Emask 0x10 SAct 0x0 SErr 0x100 action 0x2
[29559.807555] ata15.00: port_status 0x20200000
[29559.807573] ata15.00: cmd 25/00:00:00:51:77/00:04:30:00:00/e0 tag 0 cdb 0x0 data 524288 in
[29559.807575] res 51/0c:9f:61:52:77/0c:02:30:00:00/e0 Emask 0x10 (ATA bus error)
[29559.807654] ata15: hard resetting port
[29560.313376] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[29560.394924] ata15.00: configured for UDMA/33
[29560.394961] ata15: EH complete
[29560.543396] sd 14:0:0:0: [sdn] 1465149168 512-byte hardware sectors (750156 MB)
[29560.573796] sd 14:0:0:0: [sdn] Write Protect is off
[29560.573825] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[29560.657737] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Regards,
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
^ permalink raw reply [flat|nested] 15+ messages in thread* Re: Still having problems with sata_promise on all late kernels - shutdown too
2007-08-14 3:04 Still having problems with sata_promise on all late kernels Brad Campbell
@ 2007-08-14 4:37 ` Brad Campbell
2007-08-14 16:42 ` Still having problems with sata_promise on all late kernels - shutdown too - BISECTED Brad Campbell
2007-08-14 10:20 ` Still having problems with sata_promise on all late kernels Tejun Heo
1 sibling, 1 reply; 15+ messages in thread
From: Brad Campbell @ 2007-08-14 4:37 UTC (permalink / raw)
To: linux-ide
Brad Campbell wrote:
> G'day all,
>
> This has been happening on a lightly loaded box for a while now. I have
> posted about it before.
> The issue is now I've upgraded 3 drives from 250GB Maxtors to 750GB
> WD's, it's just getting worse, particularly when the drives are loaded.
>
Oh, I forgot, I still have the problem where I can't shut the box down. The SCSI layer tries to sync
cache on the drives, the 1st one errors out, and when the controller tries a hard reset on the port
the box locks hard requiring a hard poweroff or a hard reset. (No serial console, sysrq, NMI oopser
or anything else works)
I have 2 boxes with sata_promise controllers and they both do this. Not surprising given they are
both running late kernels (> 2.6.20) and both have almost exactly the same hardware in them.
http://www.fnarfbargle.com/CIMG1029.JPG (I have posted this screen shot previously. It's still doing
exactly the same thing on both boxes).
I've played with options to halt and all the other things I can think of. I just can't get it to
shut down cleanly and all 15 drives go *clunk* when I have to hard power off the box. Normally this
is not an issue as it happens once or twice a year at most, but recently I've been doing some server
room reconfiguration and have had to do a number of power cycles. Nothing like 30 drives across 2
machines going *clunk* to make your stomach turn.
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels - shutdown too - BISECTED
2007-08-14 4:37 ` Still having problems with sata_promise on all late kernels - shutdown too Brad Campbell
@ 2007-08-14 16:42 ` Brad Campbell
2007-08-15 7:50 ` Tejun Heo
0 siblings, 1 reply; 15+ messages in thread
From: Brad Campbell @ 2007-08-14 16:42 UTC (permalink / raw)
To: linux-ide
Brad Campbell wrote:
> http://www.fnarfbargle.com/CIMG1029.JPG (I have posted this screen shot
> previously. It's still doing exactly the same thing on both boxes).
>
git-bisect shows up this commit as the guilty party. I can't just revert it on a recent tree though.
Will investigate further.
brad@bkmac:~/git/linux-2.6$ git-bisect good
13b8d09f5de0aaa3153bbccc98baf247387823dc is first bad commit
commit 13b8d09f5de0aaa3153bbccc98baf247387823dc
Author: Tejun Heo <htejun@gmail.com>
Date: Tue May 15 12:29:22 2007 +0200
libata: track spindown status and skip spindown_compat if possible
Our assumption that most distros issue STANDBYNOW seems wrong. The
upstream sysvinit and thus many distros including gentoo and opensuse
don't take any action for libata disks on spindown. We can skip
compat handling for these distros so that they don't need to update
anything to take advantage of kernel-side shutdown.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
:040000 040000 6084e11e2d53daf2506d16896d0aa5635f95a9af cd30a7aad2a6a6af63779797889d4d9eed52e473 M
drivers
:040000 040000 75e3a561488e2902eed8f197da960e55fbd88f27 a7f586a83645bedbce4b4286c2e9dbcfd69f8f86 M
include
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
^ permalink raw reply [flat|nested] 15+ messages in thread* Re: Still having problems with sata_promise on all late kernels - shutdown too - BISECTED
2007-08-14 16:42 ` Still having problems with sata_promise on all late kernels - shutdown too - BISECTED Brad Campbell
@ 2007-08-15 7:50 ` Tejun Heo
2007-08-15 16:18 ` Brad Campbell
0 siblings, 1 reply; 15+ messages in thread
From: Tejun Heo @ 2007-08-15 7:50 UTC (permalink / raw)
To: Brad Campbell; +Cc: linux-ide
Brad Campbell wrote:
> Brad Campbell wrote:
>
>> http://www.fnarfbargle.com/CIMG1029.JPG (I have posted this screen
>> shot previously. It's still doing exactly the same thing on both boxes).
>>
>
> git-bisect shows up this commit as the guilty party. I can't just revert
> it on a recent tree though.
> Will investigate further.
Weird. Does 'hdparm -y /dev/sdX' work?
--
tejun
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels - shutdown too - BISECTED
2007-08-15 7:50 ` Tejun Heo
@ 2007-08-15 16:18 ` Brad Campbell
2007-08-16 5:43 ` Tejun Heo
0 siblings, 1 reply; 15+ messages in thread
From: Brad Campbell @ 2007-08-15 16:18 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-ide
Tejun Heo wrote:
> Brad Campbell wrote:
>> Brad Campbell wrote:
>>
>>> http://www.fnarfbargle.com/CIMG1029.JPG (I have posted this screen
>>> shot previously. It's still doing exactly the same thing on both boxes).
>>>
>> git-bisect shows up this commit as the guilty party. I can't just revert
>> it on a recent tree though.
>> Will investigate further.
>
> Weird. Does 'hdparm -y /dev/sdX' work?
Very interesting indeed..
for i in /dev/sd* ; do echo $i ; hdparm -y $i ; done
sda-sdh worked fine.. sdi locked the box.
So it's dying on the 3rd or 4th controller.
Now that I think about it, on the other side of the git bisect I probably only heard 8 clicks as the
kernel shut down the 1st 8 drives, then the remainder powered off when the machine powered off.
So even prior to this it was probably only shutting down the 1st 8 drives properly.
brad@storage1:~$ lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge (rev 80)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
00:09.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T [Marvell] (rev 12)
00:0b.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
00:0d.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
00:0e.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master
IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller
(rev 60)
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
00:13.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 315PRO PCI/AGP VGA Display Adapter
[ 46.624922] sata_promise 0000:00:0b.0: version 2.07
[ 46.624937] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 17
[ 46.641073] scsi0 : sata_promise
[ 46.641301] scsi1 : sata_promise
[ 46.641471] scsi2 : sata_promise
[ 46.648281] scsi3 : sata_promise
[ 46.654924] ata1: SATA max UDMA/133 cmd 0xf8816200 ctl 0xf8816238 bmdma 0x00000000 irq 0
[ 46.661784] ata2: SATA max UDMA/133 cmd 0xf8816280 ctl 0xf88162b8 bmdma 0x00000000 irq 0
[ 46.668432] ata3: SATA max UDMA/133 cmd 0xf8816300 ctl 0xf8816338 bmdma 0x00000000 irq 0
[ 46.674895] ata4: SATA max UDMA/133 cmd 0xf8816380 ctl 0xf88163b8 bmdma 0x00000000 irq 0
[ 47.170019] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 47.190471] ata1.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 47.197090] ata1.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 47.203704] ata1.00: 490234752 sectors, multi 0: LBA48
[ 47.230410] ata1.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 47.237100] ata1.00: configured for UDMA/133
[ 47.729427] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 47.749866] ata2.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 47.756760] ata2.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 47.763727] ata2.00: 490234752 sectors, multi 0: LBA48
[ 47.789820] ata2.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 47.796966] ata2.00: configured for UDMA/133
[ 48.288835] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 48.309277] ata3.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 48.316381] ata3.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 48.323494] ata3.00: 490234752 sectors, multi 0: LBA48
[ 48.349233] ata3.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 48.356411] ata3.00: configured for UDMA/133
[ 48.848245] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 48.868684] ata4.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 48.875960] ata4.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 48.883230] ata4.00: 490234752 sectors, multi 0: LBA48
[ 48.908634] ata4.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 48.916000] ata4.00: configured for UDMA/133
[ 48.923402] scsi 0:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 48.931040] sd 0:0:0:0: [sda] 490234752 512-byte hardware sectors (251000 MB)
[ 48.938540] sd 0:0:0:0: [sda] Write Protect is off
[ 48.945849] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 48.945865] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 48.953425] sd 0:0:0:0: [sda] 490234752 512-byte hardware sectors (251000 MB)
[ 48.960907] sd 0:0:0:0: [sda] Write Protect is off
[ 48.968251] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 48.968265] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 48.975808] sda: unknown partition table
[ 55.984630] sd 0:0:0:0: [sda] Attached SCSI disk
[ 55.992218] scsi 1:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 55.999870] sd 1:0:0:0: [sdb] 490234752 512-byte hardware sectors (251000 MB)
[ 56.007421] sd 1:0:0:0: [sdb] Write Protect is off
[ 56.015029] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 56.015045] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.023013] sd 1:0:0:0: [sdb] 490234752 512-byte hardware sectors (251000 MB)
[ 56.031098] sd 1:0:0:0: [sdb] Write Protect is off
[ 56.039005] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 56.039019] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.047244] sdb: unknown partition table
[ 63.431266] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 63.439764] scsi 2:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 63.448337] sd 2:0:0:0: [sdc] 490234752 512-byte hardware sectors (251000 MB)
[ 63.456799] sd 2:0:0:0: [sdc] Write Protect is off
[ 63.465117] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 63.465133] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 63.473672] sd 2:0:0:0: [sdc] 490234752 512-byte hardware sectors (251000 MB)
[ 63.482133] sd 2:0:0:0: [sdc] Write Protect is off
[ 63.490472] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 63.490486] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 63.498998] sdc: unknown partition table
[ 70.770909] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 70.779326] scsi 3:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 70.787888] sd 3:0:0:0: [sdd] 490234752 512-byte hardware sectors (251000 MB)
[ 70.796358] sd 3:0:0:0: [sdd] Write Protect is off
[ 70.804686] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.804700] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.813235] sd 3:0:0:0: [sdd] 490234752 512-byte hardware sectors (251000 MB)
[ 70.821679] sd 3:0:0:0: [sdd] Write Protect is off
[ 70.829976] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.829991] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.838476] sdd: unknown partition table
[ 78.098488] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 78.106864] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 18
[ 78.127345] scsi4 : sata_promise
[ 78.135687] scsi5 : sata_promise
[ 78.143830] scsi6 : sata_promise
[ 78.151848] scsi7 : sata_promise
[ 78.159669] ata5: SATA max UDMA/133 cmd 0xf881e200 ctl 0xf881e238 bmdma 0x00000000 irq 0
[ 78.167664] ata6: SATA max UDMA/133 cmd 0xf881e280 ctl 0xf881e2b8 bmdma 0x00000000 irq 0
[ 78.175472] ata7: SATA max UDMA/133 cmd 0xf881e300 ctl 0xf881e338 bmdma 0x00000000 irq 0
[ 78.183099] ata8: SATA max UDMA/133 cmd 0xf881e380 ctl 0xf881e3b8 bmdma 0x00000000 irq 0
[ 78.676722] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 78.697172] ata5.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 78.704683] ata5.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 78.712191] ata5.00: 490234752 sectors, multi 0: LBA48
[ 78.737112] ata5.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 78.744592] ata5.00: configured for UDMA/133
[ 79.236129] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 79.256570] ata6.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 79.264101] ata6.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 79.271619] ata6.00: 490234752 sectors, multi 0: LBA48
[ 79.296521] ata6.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 79.304040] ata6.00: configured for UDMA/133
[ 79.795538] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 79.815978] ata7.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 79.823495] ata7.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 79.831032] ata7.00: 490234752 sectors, multi 0: LBA48
[ 79.855930] ata7.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 79.863472] ata7.00: configured for UDMA/133
[ 80.354946] ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 80.375384] ata8.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 80.382952] ata8.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 80.390513] ata8.00: 490234752 sectors, multi 0: LBA48
[ 80.415342] ata8.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 80.422877] ata8.00: configured for UDMA/133
[ 80.430470] scsi 4:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 80.438232] sd 4:0:0:0: [sde] 490234752 512-byte hardware sectors (251000 MB)
[ 80.445848] sd 4:0:0:0: [sde] Write Protect is off
[ 80.453366] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 80.453383] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 80.461109] sd 4:0:0:0: [sde] 490234752 512-byte hardware sectors (251000 MB)
[ 80.468723] sd 4:0:0:0: [sde] Write Protect is off
[ 80.476237] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 80.476252] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 80.483922] sde: unknown partition table
[ 87.806745] sd 4:0:0:0: [sde] Attached SCSI disk
[ 87.814366] scsi 5:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 87.822071] sd 5:0:0:0: [sdf] 490234752 512-byte hardware sectors (251000 MB)
[ 87.829682] sd 5:0:0:0: [sdf] Write Protect is off
[ 87.837329] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 87.837344] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 87.845348] sd 5:0:0:0: [sdf] 490234752 512-byte hardware sectors (251000 MB)
[ 87.853458] sd 5:0:0:0: [sdf] Write Protect is off
[ 87.861397] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 87.861412] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 87.869672] sdf: unknown partition table
[ 95.284548] sd 5:0:0:0: [sdf] Attached SCSI disk
[ 95.293075] scsi 6:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 95.301680] sd 6:0:0:0: [sdg] 490234752 512-byte hardware sectors (251000 MB)
[ 95.310178] sd 6:0:0:0: [sdg] Write Protect is off
[ 95.318525] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 95.318539] sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 95.327110] sd 6:0:0:0: [sdg] 490234752 512-byte hardware sectors (251000 MB)
[ 95.335614] sd 6:0:0:0: [sdg] Write Protect is off
[ 95.343981] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 95.343995] sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 95.352533] sdg: unknown partition table
[ 102.740714] sd 6:0:0:0: [sdg] Attached SCSI disk
[ 102.749171] scsi 7:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 102.757758] sd 7:0:0:0: [sdh] 490234752 512-byte hardware sectors (251000 MB)
[ 102.766256] sd 7:0:0:0: [sdh] Write Protect is off
[ 102.774610] sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 102.774626] sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 102.783186] sd 7:0:0:0: [sdh] 490234752 512-byte hardware sectors (251000 MB)
[ 102.791650] sd 7:0:0:0: [sdh] Write Protect is off
[ 102.799970] sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 102.799984] sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 102.808492] sdh: unknown partition table
[ 110.116127] sd 7:0:0:0: [sdh] Attached SCSI disk
[ 110.124553] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 19
[ 110.143509] scsi8 : sata_promise
[ 110.151883] scsi9 : sata_promise
[ 110.160052] scsi10 : sata_promise
[ 110.168136] scsi11 : sata_promise
[ 110.176031] ata9: SATA max UDMA/133 cmd 0xf8820200 ctl 0xf8820238 bmdma 0x00000000 irq 0
[ 110.184099] ata10: SATA max UDMA/133 cmd 0xf8820280 ctl 0xf88202b8 bmdma 0x00000000 irq 0
[ 110.192172] ata11: SATA max UDMA/133 cmd 0xf8820300 ctl 0xf8820338 bmdma 0x00000000 irq 0
[ 110.200062] ata12: SATA max UDMA/133 cmd 0xf8820380 ctl 0xf88203b8 bmdma 0x00000000 irq 0
[ 110.692889] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 110.713389] ata9.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 110.721175] ata9.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 110.728956] ata9.00: 490234752 sectors, multi 0: LBA48
[ 110.753329] ata9.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 110.761077] ata9.00: configured for UDMA/133
[ 111.252296] ata10: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 111.272785] ata10.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 111.280580] ata10.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 111.288370] ata10.00: 490234752 sectors, multi 0: LBA48
[ 111.312741] ata10.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 111.320533] ata10.00: configured for UDMA/133
[ 111.811705] ata11: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 111.832188] ata11.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 111.839981] ata11.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 111.847786] ata11.00: 490234752 sectors, multi 0: LBA48
[ 111.872156] ata11.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 111.879951] ata11.00: configured for UDMA/133
[ 112.371114] ata12: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 112.391607] ata12.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 112.399417] ata12.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 112.407218] ata12.00: 490234752 sectors, multi 0: LBA48
[ 112.431552] ata12.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 112.439320] ata12.00: configured for UDMA/133
[ 112.447134] scsi 8:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 112.455125] sd 8:0:0:0: [sdi] 490234752 512-byte hardware sectors (251000 MB)
[ 112.462964] sd 8:0:0:0: [sdi] Write Protect is off
[ 112.470702] sd 8:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[ 112.470717] sd 8:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.478673] sd 8:0:0:0: [sdi] 490234752 512-byte hardware sectors (251000 MB)
[ 112.486513] sd 8:0:0:0: [sdi] Write Protect is off
[ 112.494254] sd 8:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[ 112.494268] sd 8:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.502167] sdi: unknown partition table
[ 112.529588] sd 8:0:0:0: [sdi] Attached SCSI disk
[ 112.537413] scsi 9:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 112.545323] sd 9:0:0:0: [sdj] 490234752 512-byte hardware sectors (251000 MB)
[ 112.553145] sd 9:0:0:0: [sdj] Write Protect is off
[ 112.561007] sd 9:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 112.561021] sd 9:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.569190] sd 9:0:0:0: [sdj] 490234752 512-byte hardware sectors (251000 MB)
[ 112.577468] sd 9:0:0:0: [sdj] Write Protect is off
[ 112.585577] sd 9:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 112.585591] sd 9:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.593829] sdj: unknown partition table
[ 112.617892] sd 9:0:0:0: [sdj] Attached SCSI disk
[ 112.626370] scsi 10:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 112.634936] sd 10:0:0:0: [sdk] 490234752 512-byte hardware sectors (251000 MB)
[ 112.643405] sd 10:0:0:0: [sdk] Write Protect is off
[ 112.651729] sd 10:0:0:0: [sdk] Mode Sense: 00 3a 00 00
[ 112.651744] sd 10:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.660296] sd 10:0:0:0: [sdk] 490234752 512-byte hardware sectors (251000 MB)
[ 112.668776] sd 10:0:0:0: [sdk] Write Protect is off
[ 112.677116] sd 10:0:0:0: [sdk] Mode Sense: 00 3a 00 00
[ 112.677136] sd 10:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.685648] sdk: unknown partition table
[ 112.717384] sd 10:0:0:0: [sdk] Attached SCSI disk
[ 112.725810] scsi 11:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 112.734392] sd 11:0:0:0: [sdl] 490234752 512-byte hardware sectors (251000 MB)
[ 112.742893] sd 11:0:0:0: [sdl] Write Protect is off
[ 112.751255] sd 11:0:0:0: [sdl] Mode Sense: 00 3a 00 00
[ 112.751269] sd 11:0:0:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.759834] sd 11:0:0:0: [sdl] 490234752 512-byte hardware sectors (251000 MB)
[ 112.768308] sd 11:0:0:0: [sdl] Write Protect is off
[ 112.776644] sd 11:0:0:0: [sdl] Mode Sense: 00 3a 00 00
[ 112.776657] sd 11:0:0:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.785186] sdl: unknown partition table
[ 112.815809] sd 11:0:0:0: [sdl] Attached SCSI disk
[ 112.824267] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 16
[ 112.850639] scsi12 : sata_promise
[ 112.859064] scsi13 : sata_promise
[ 112.867290] scsi14 : sata_promise
[ 112.875389] scsi15 : sata_promise
[ 112.883301] ata13: SATA max UDMA/133 cmd 0xf8822200 ctl 0xf8822238 bmdma 0x00000000 irq 0
[ 112.891386] ata14: SATA max UDMA/133 cmd 0xf8822280 ctl 0xf88222b8 bmdma 0x00000000 irq 0
[ 112.899281] ata15: SATA max UDMA/133 cmd 0xf8822300 ctl 0xf8822338 bmdma 0x00000000 irq 0
[ 112.906993] ata16: SATA max UDMA/133 cmd 0xf8822380 ctl 0xf88223b8 bmdma 0x00000000 irq 0
[ 113.400028] ata13: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 113.420538] ata13.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 113.428125] ata13.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 113.435704] ata13.00: 490234752 sectors, multi 0: LBA48
[ 113.460465] ata13.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 113.468012] ata13.00: configured for UDMA/133
[ 113.959436] ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 113.979922] ata14.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 113.987525] ata14.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 113.995118] ata14.00: 490234752 sectors, multi 0: LBA48
[ 114.019875] ata14.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 114.027476] ata14.00: configured for UDMA/133
[ 114.518843] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 114.539331] ata15.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 114.546918] ata15.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 114.554531] ata15.00: 490234752 sectors, multi 0: LBA48
[ 114.579302] ata15.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 114.586895] ata15.00: configured for UDMA/133
[ 114.918403] ata16: SATA link down (SStatus 0 SControl 0)
[ 114.926018] scsi 12:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 114.933755] sd 12:0:0:0: [sdm] 490234752 512-byte hardware sectors (251000 MB)
[ 114.941420] sd 12:0:0:0: [sdm] Write Protect is off
[ 114.948955] sd 12:0:0:0: [sdm] Mode Sense: 00 3a 00 00
[ 114.948971] sd 12:0:0:0: [sdm] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 114.956622] sd 12:0:0:0: [sdm] 490234752 512-byte hardware sectors (251000 MB)
[ 114.964258] sd 12:0:0:0: [sdm] Write Protect is off
[ 114.971763] sd 12:0:0:0: [sdm] Mode Sense: 00 3a 00 00
[ 114.971777] sd 12:0:0:0: [sdm] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 114.979404] sdm: unknown partition table
[ 115.004878] sd 12:0:0:0: [sdm] Attached SCSI disk
[ 115.012514] scsi 13:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 115.020224] sd 13:0:0:0: [sdn] 490234752 512-byte hardware sectors (251000 MB)
[ 115.027883] sd 13:0:0:0: [sdn] Write Protect is off
[ 115.035414] sd 13:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[ 115.035430] sd 13:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 115.043070] sd 13:0:0:0: [sdn] 490234752 512-byte hardware sectors (251000 MB)
[ 115.050705] sd 13:0:0:0: [sdn] Write Protect is off
[ 115.058187] sd 13:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[ 115.058200] sd 13:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 115.065817] sdn: unknown partition table
[ 115.092809] sd 13:0:0:0: [sdn] Attached SCSI disk
[ 115.100723] scsi 14:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 115.108931] sd 14:0:0:0: [sdo] 490234752 512-byte hardware sectors (251000 MB)
[ 115.117005] sd 14:0:0:0: [sdo] Write Protect is off
[ 115.125124] sd 14:0:0:0: [sdo] Mode Sense: 00 3a 00 00
[ 115.125139] sd 14:0:0:0: [sdo] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 115.133606] sd 14:0:0:0: [sdo] 490234752 512-byte hardware sectors (251000 MB)
[ 115.142171] sd 14:0:0:0: [sdo] Write Protect is off
[ 115.150580] sd 14:0:0:0: [sdo] Mode Sense: 00 3a 00 00
[ 115.150595] sd 14:0:0:0: [sdo] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 115.159136] sdo: unknown partition table
[ 115.185583] sd 14:0:0:0: [sdo] Attached SCSI disk
[ 115.194181] pata_via 0000:00:0f.1: version 0.3.1
[ 115.194253] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 20
[ 115.202806] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 115.211316] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels - shutdown too - BISECTED
2007-08-15 16:18 ` Brad Campbell
@ 2007-08-16 5:43 ` Tejun Heo
2007-08-16 7:54 ` Brad Campbell
0 siblings, 1 reply; 15+ messages in thread
From: Tejun Heo @ 2007-08-16 5:43 UTC (permalink / raw)
To: Brad Campbell; +Cc: linux-ide
Brad Campbell wrote:
> Tejun Heo wrote:
>> Brad Campbell wrote:
>>> Brad Campbell wrote:
>>>
>>>> http://www.fnarfbargle.com/CIMG1029.JPG (I have posted this screen
>>>> shot previously. It's still doing exactly the same thing on both
>>>> boxes).
>>>>
>>> git-bisect shows up this commit as the guilty party. I can't just revert
>>> it on a recent tree though.
>>> Will investigate further.
>>
>> Weird. Does 'hdparm -y /dev/sdX' work?
>
> Very interesting indeed..
>
> for i in /dev/sd* ; do echo $i ; hdparm -y $i ; done
>
> sda-sdh worked fine.. sdi locked the box.
>
> So it's dying on the 3rd or 4th controller.
That's weird. You seem to have the same controllers and drives. What
happens if you spin down from hdi upwards?
--
tejun
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels - shutdown too - BISECTED
2007-08-16 5:43 ` Tejun Heo
@ 2007-08-16 7:54 ` Brad Campbell
2007-08-16 11:10 ` Tejun Heo
0 siblings, 1 reply; 15+ messages in thread
From: Brad Campbell @ 2007-08-16 7:54 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-ide
Tejun Heo wrote:
> Brad Campbell wrote:
>> Tejun Heo wrote:
>>> Brad Campbell wrote:
>>>> Brad Campbell wrote:
>>>>
>>>>> http://www.fnarfbargle.com/CIMG1029.JPG (I have posted this screen
>>>>> shot previously. It's still doing exactly the same thing on both
>>>>> boxes).
>>>>>
>>>> git-bisect shows up this commit as the guilty party. I can't just revert
>>>> it on a recent tree though.
>>>> Will investigate further.
>>> Weird. Does 'hdparm -y /dev/sdX' work?
>> Very interesting indeed..
>>
>> for i in /dev/sd* ; do echo $i ; hdparm -y $i ; done
>>
>> sda-sdh worked fine.. sdi locked the box.
>>
>> So it's dying on the 3rd or 4th controller.
>
> That's weird. You seem to have the same controllers and drives. What
> happens if you spin down from hdi upwards?
>
Any attempt to spin down sdi-sdo in any order locks hard. Any attempt to spin down sda-sdh works in
any combination/permutation.
Yes, all controllers and drives are identical.
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels - shutdown too - BISECTED
2007-08-16 7:54 ` Brad Campbell
@ 2007-08-16 11:10 ` Tejun Heo
2007-08-16 11:22 ` Brad Campbell
0 siblings, 1 reply; 15+ messages in thread
From: Tejun Heo @ 2007-08-16 11:10 UTC (permalink / raw)
To: Brad Campbell; +Cc: linux-ide
Brad Campbell wrote:
> Tejun Heo wrote:
>> Brad Campbell wrote:
>>> Tejun Heo wrote:
>>>> Brad Campbell wrote:
>>>>> Brad Campbell wrote:
>>>>>
>>>>>> http://www.fnarfbargle.com/CIMG1029.JPG (I have posted this screen
>>>>>> shot previously. It's still doing exactly the same thing on both
>>>>>> boxes).
>>>>>>
>>>>> git-bisect shows up this commit as the guilty party. I can't just
>>>>> revert
>>>>> it on a recent tree though.
>>>>> Will investigate further.
>>>> Weird. Does 'hdparm -y /dev/sdX' work?
>>> Very interesting indeed..
>>>
>>> for i in /dev/sd* ; do echo $i ; hdparm -y $i ; done
>>>
>>> sda-sdh worked fine.. sdi locked the box.
>>>
>>> So it's dying on the 3rd or 4th controller.
>>
>> That's weird. You seem to have the same controllers and drives. What
>> happens if you spin down from hdi upwards?
>>
>
> Any attempt to spin down sdi-sdo in any order locks hard. Any attempt to
> spin down sda-sdh works in any combination/permutation.
Hmmm... I'm out of ideas. It definitely sounds like some sort of
hardware problem to me. I think the best way to diagnose the problem is
playing the tedious but often rewarding add-remove-swap game with the
hardware and see to which piece or combination of pieces the problem is
attached.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels - shutdown too - BISECTED
2007-08-16 11:10 ` Tejun Heo
@ 2007-08-16 11:22 ` Brad Campbell
0 siblings, 0 replies; 15+ messages in thread
From: Brad Campbell @ 2007-08-16 11:22 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-ide
Tejun Heo wrote:
>> Any attempt to spin down sdi-sdo in any order locks hard. Any attempt to
>> spin down sda-sdh works in any combination/permutation.
>
> Hmmm... I'm out of ideas. It definitely sounds like some sort of
> hardware problem to me. I think the best way to diagnose the problem is
> playing the tedious but often rewarding add-remove-swap game with the
> hardware and see to which piece or combination of pieces the problem is
> attached.
The problem appears to be having more than 2 Promise cards in the system. Both machines have >2
cards (one has 3 and the other has 4) and they both lock up on shutdown in the same fashion (first 8
drives are ok, then it locks).
Between this and the intermittent BUS Errors under load, perhaps I toss the promise cards and
upgrade to some 4 port SIL cards instead.
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels
2007-08-14 3:04 Still having problems with sata_promise on all late kernels Brad Campbell
2007-08-14 4:37 ` Still having problems with sata_promise on all late kernels - shutdown too Brad Campbell
@ 2007-08-14 10:20 ` Tejun Heo
2007-08-14 10:42 ` Brad Campbell
2007-08-14 13:52 ` Brad Campbell
1 sibling, 2 replies; 15+ messages in thread
From: Tejun Heo @ 2007-08-14 10:20 UTC (permalink / raw)
To: Brad Campbell; +Cc: linux-ide
Brad Campbell wrote:
> G'day all,
>
> This has been happening on a lightly loaded box for a while now. I have
> posted about it before.
> The issue is now I've upgraded 3 drives from 250GB Maxtors to 750GB
> WD's, it's just getting worse, particularly when the drives are loaded.
> I've jumpered the WD's to 1.5GB PHY speed (I had to do that or the
> on-board via sata controller would not recognise one of the drives.
> The box is a bit of a mish-mash of controllers. I have 3 Promise
> SATA150TX4, one SIL3112 (all on PCI cards) and the on-board 2 port VIA
> driver.
>
> I'm at a bit of a loss as to what to do really, short of replacing the
> Promise cards with something else.
ATA bus error is a strong indicator for hardware problem. Please get a
separate power supply (doesn't have to be an expensive one), power it up
[1], and connect some of the drives to the power supply and see whether
errors persist on those drives.
--
tejun
[1] http://modtown.co.uk/mt/article2.php?id=psumod
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels
2007-08-14 10:20 ` Still having problems with sata_promise on all late kernels Tejun Heo
@ 2007-08-14 10:42 ` Brad Campbell
2007-08-14 13:52 ` Brad Campbell
1 sibling, 0 replies; 15+ messages in thread
From: Brad Campbell @ 2007-08-14 10:42 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-ide
Tejun Heo wrote:
> Brad Campbell wrote:
>> G'day all,
>>
>> This has been happening on a lightly loaded box for a while now. I have
>> posted about it before.
>> The issue is now I've upgraded 3 drives from 250GB Maxtors to 750GB
>> WD's, it's just getting worse, particularly when the drives are loaded.
>> I've jumpered the WD's to 1.5GB PHY speed (I had to do that or the
>> on-board via sata controller would not recognise one of the drives.
>> The box is a bit of a mish-mash of controllers. I have 3 Promise
>> SATA150TX4, one SIL3112 (all on PCI cards) and the on-board 2 port VIA
>> driver.
>>
>> I'm at a bit of a loss as to what to do really, short of replacing the
>> Promise cards with something else.
>
> ATA bus error is a strong indicator for hardware problem. Please get a
> separate power supply (doesn't have to be an expensive one), power it up
> [1], and connect some of the drives to the power supply and see whether
> errors persist on those drives.
>
Hrm, I did try that a while back. I'll give that a bash again tonight.
This is only happening on the Promise cards. The drives on the SIL and VIA controllers will work as
hard as I care to work them and never fault.
I'll try and do a GIT bisection this evening, If I go back to 2.6.16 I get no errors and the system
works perfectly well. Same can be said for the failure to shut down actually. 2.6.16 worked flawlessly.
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels
2007-08-14 10:20 ` Still having problems with sata_promise on all late kernels Tejun Heo
2007-08-14 10:42 ` Brad Campbell
@ 2007-08-14 13:52 ` Brad Campbell
2007-08-15 7:54 ` Tejun Heo
1 sibling, 1 reply; 15+ messages in thread
From: Brad Campbell @ 2007-08-14 13:52 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-ide
Tejun Heo wrote:
> ATA bus error is a strong indicator for hardware problem. Please get a
> separate power supply (doesn't have to be an expensive one), power it up
> [1], and connect some of the drives to the power supply and see whether
> errors persist on those drives.
>
2 separate tests with the 2 troublesome drives, each time with both drives on a different power
supply unit. Also tried new cables from a different manufacturer.
It ain't the cables and it ain't the power.
Regards,
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels
2007-08-14 13:52 ` Brad Campbell
@ 2007-08-15 7:54 ` Tejun Heo
0 siblings, 0 replies; 15+ messages in thread
From: Tejun Heo @ 2007-08-15 7:54 UTC (permalink / raw)
To: Brad Campbell; +Cc: linux-ide, Mikael Pettersson
[cc'ing Mikael Pettersson]
Brad Campbell wrote:
> Tejun Heo wrote:
>
>> ATA bus error is a strong indicator for hardware problem. Please get a
>> separate power supply (doesn't have to be an expensive one), power it up
>> [1], and connect some of the drives to the power supply and see whether
>> errors persist on those drives.
>>
>
> 2 separate tests with the 2 troublesome drives, each time with both
> drives on a different power supply unit. Also tried new cables from a
> different manufacturer.
>
> It ain't the cables and it ain't the power.
I see. Thanks. I'm pretty much out of ideas at this point. Mikael?
--
tejun
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels
@ 2007-08-15 15:39 Mikael Pettersson
2007-08-15 16:36 ` Brad Campbell
0 siblings, 1 reply; 15+ messages in thread
From: Mikael Pettersson @ 2007-08-15 15:39 UTC (permalink / raw)
To: brad, htejun; +Cc: linux-ide, mikpe
On Wed, 15 Aug 2007 16:54:52 +0900, Tejun Heo wrote:
>Brad Campbell wrote:
>> Tejun Heo wrote:
>>
>>> ATA bus error is a strong indicator for hardware problem. Please get a
>>> separate power supply (doesn't have to be an expensive one), power it up
>>> [1], and connect some of the drives to the power supply and see whether
>>> errors persist on those drives.
>>>
>>
>> 2 separate tests with the 2 troublesome drives, each time with both
>> drives on a different power supply unit. Also tried new cables from a
>> different manufacturer.
>>
>> It ain't the cables and it ain't the power.
>
>I see. Thanks. I'm pretty much out of ideas at this point. Mikael?
The box was described as a KT600 chipset era machine
with 3 Promise SATA150TX4 cards, a SIL3112 card, and
an on-board VIA controller. According to the `lspci'
posted the box probably also has an AGP card and at
least one gigaether card (there's two, I guess one might
be built-in).
All in all, a rather heavily loaded (in terms of power,
cooling, and the PCI bus) box (for a desktop chipset).
I've never seen the SATA150-generation cards misbehave,
so at this point I have to assume that it's a system
limit issue, be it PCI, power, or cooling.
/Mikael
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Still having problems with sata_promise on all late kernels
2007-08-15 15:39 Mikael Pettersson
@ 2007-08-15 16:36 ` Brad Campbell
0 siblings, 0 replies; 15+ messages in thread
From: Brad Campbell @ 2007-08-15 16:36 UTC (permalink / raw)
To: Mikael Pettersson; +Cc: htejun, linux-ide
Mikael Pettersson wrote:
> The box was described as a KT600 chipset era machine
> with 3 Promise SATA150TX4 cards, a SIL3112 card, and
> an on-board VIA controller. According to the `lspci'
> posted the box probably also has an AGP card and at
> least one gigaether card (there's two, I guess one might
> be built-in).
One PCI and one on-board. Otherwise quite an accurate assessment.
> All in all, a rather heavily loaded (in terms of power,
> cooling, and the PCI bus) box (for a desktop chipset).
Yes, cooling is not an issue. The motherboard reports 28-29C, the processor is 32-34C and the drives
all report between 32-38C. The machine has an excessive number of fans in it and the drives live in
Supermicro hotswap bays with 90mm high speed noise makers strapped to the back. The machines live in
a separate air conditioned and UPS'd environment which is regulated at 20C. I've put a thermocouple
in the machine and I never see temperatures on any of the hardware exceeding 40C (Graphics card
heatsink)
The PSU is a 4 x 12v rail Thermaltake 600W jobbie with the 12v rails re-wired to feed mainly the
drives (as one 18A rail would not do 15 drives all spinning up together). The PSU is now identical
to the one fitted to its sister box. I've measured the voltages all within tolerance and the fully
loaded ripple is less than 50mv on +5 and all +12 rails. That looks pretty good to me.
This is the second PSU the box has seen as I just upgraded it from the old 420W that was in there.
I have tried splitting the drives over 2 PSU's (several different combinations of drives and PSU's)
and the problem still exists.
> I've never seen the SATA150-generation cards misbehave,
> so at this point I have to assume that it's a system
> limit issue, be it PCI, power, or cooling.
It may well be a PCI bus issue however it's sister box which is exactly the same mainboard has 15
drives on 4 SATA150 cards and it has never had such a problem. It just locks up on shutdown :)
I will note that this machine has run (except for the lower wattage PSU) in this configuration since
about 2.6.9 and sat perfectly happy with 2.6.16 until I needed to upgrade for some reason around
2.6.21-rc (which is when the bus errors started).
I'll try some more conservative PCI settings in the BIOS and see what happens.
Thanks for the pointers anyway.
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2007-08-16 11:22 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-08-14 3:04 Still having problems with sata_promise on all late kernels Brad Campbell
2007-08-14 4:37 ` Still having problems with sata_promise on all late kernels - shutdown too Brad Campbell
2007-08-14 16:42 ` Still having problems with sata_promise on all late kernels - shutdown too - BISECTED Brad Campbell
2007-08-15 7:50 ` Tejun Heo
2007-08-15 16:18 ` Brad Campbell
2007-08-16 5:43 ` Tejun Heo
2007-08-16 7:54 ` Brad Campbell
2007-08-16 11:10 ` Tejun Heo
2007-08-16 11:22 ` Brad Campbell
2007-08-14 10:20 ` Still having problems with sata_promise on all late kernels Tejun Heo
2007-08-14 10:42 ` Brad Campbell
2007-08-14 13:52 ` Brad Campbell
2007-08-15 7:54 ` Tejun Heo
-- strict thread matches above, loose matches on Subject: below --
2007-08-15 15:39 Mikael Pettersson
2007-08-15 16:36 ` Brad Campbell
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).
