* regression problem with Maxtor disk
@ 2007-08-12 14:14 Lieven Marchand
2007-08-14 9:50 ` Tejun Heo
0 siblings, 1 reply; 8+ messages in thread
From: Lieven Marchand @ 2007-08-12 14:14 UTC (permalink / raw)
To: jgarzik; +Cc: linux-ide
Hi,
the following drive
Aug 12 12:26:15 black kernel: Vendor: ATA Model: Maxtor 7H500F0 Rev:
HA43
Aug 12 12:26:15 black kernel: Type: Direct-Access ANSI
SCSI revision: 05
works fine under 2.6.18 and crashes the boot procedure under
2.6.22. Occasionally the boot continues but most of the times the
kernel crashes with an error message of a corrupt cpu context.
I've added the logs of a succesful boot here. When such a boot
succeeds, the system is noticeably slower than under 2.6.18.
Aug 11 10:27:51 black kernel: scsi 4:0:0:0: Direct-Access ATA Maxtor 7H
500F0 HA43 PQ: 0 ANSI: 5
Aug 11 10:27:51 black kernel: ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment bou
ndary 0xFFFFFFFF, hw segs 61
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x440
Aug 11 10:27:51 black kernel: res 51/04:00:00:00:00/04:00:00:00:00/40 E
mask 0x1 (device error)
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: EH complete
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x440
Aug 11 10:27:51 black kernel: res 51/04:00:00:00:00/04:00:00:00:00/40 E
mask 0x1 (device error)
Aug 11 10:27:51 black last message repeated 2 times
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: EH complete
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and ID
LE, stat=0x440
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 E
mask 0x4 (timeout)
Aug 11 10:27:51 black last message repeated 2 times
Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 E
mask 0x4 (timeout)
Aug 11 10:27:51 black kernel: ata2: soft resetting port
Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: EH complete
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and ID
LE, stat=0x400
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
Aug 11 10:27:51 black kernel: ata2.00: NCQ disabled due to excessive errors
Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 E
mask 0x4 (timeout)
Aug 11 10:27:51 black last message repeated 2 times
Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 E
mask 0x4 (timeout)
Aug 11 10:27:51 black kernel: ata2: soft resetting port
Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: EH complete
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and ID
LE, stat=0x400
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 E
mask 0x4 (timeout)
Aug 11 10:27:51 black kernel: ata2: soft resetting port
Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: EH complete
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: regression problem with Maxtor disk
@ 2007-08-12 23:36 babl
0 siblings, 0 replies; 8+ messages in thread
From: babl @ 2007-08-12 23:36 UTC (permalink / raw)
To: linux-ide
I think, it's sata_nv driver problem. I have same bug too.
MB: ASUS A8N SLI Deluxe (nforce4 sli + sil3114)
Power: FSP Epsilon 700W
/dev/disk/by-id/scsi-SATA_Maxtor_6B200M0_B404ZB9H
/dev/disk/by-id/scsi-SATA_SAMSUNG_HD401LJS0HVJ1CP105426
/dev/disk/by-id/scsi-SATA_WDC_WD3200JD-00_WD-WCAMR1623763
/dev/disk/by-id/scsi-SATA_WDC_WD3200JS-00_WD-WCAPD1127756
/dev/disk/by-id/scsi-SATA_WDC_WD3200JS-00_WD-WCAPD2176538
/dev/disk/by-id/scsi-SATA_WDC_WD3200JS-60_WD-WCAPD2515626
/dev/disk/by-id/scsi-SATA_WDC_WD3200KS-00_WD-WCAPD2510753
/dev/disk/by-id/scsi-SATA_WDC_WD3200KS-00_WD-WCAPD3248212
When I try to copy files from one HDD to another, i have freeses and low
speed. There are soft and hard resets here and regression from UDMA/133 to
PIO.
2.6.18 (HD400LJ):
Aug 13 03:16:52 bobr kernel: ata4.00: exception Emask 0x0 SAct 0x0 SErr
0x580000 action 0x2
Aug 13 03:16:52 bobr kernel: ata4.00: (BMDMA stat 0x20)
Aug 13 03:16:52 bobr kernel: ata4.00: tag 0 cmd 0x35 Emask 0x10 stat 0x51 err
0x84 (ATA bus error)
Aug 13 03:16:53 bobr kernel: ata4: soft resetting port
Aug 13 03:16:53 bobr kernel: ata4: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Aug 13 03:16:53 bobr kernel: ata4.00: configured for UDMA/100
Aug 13 03:16:53 bobr kernel: ata4: EH complete
Aug 13 03:16:53 bobr kernel: SCSI device sdd: 625142448 512-byte hdwr sectors
(320073 MB)
Aug 13 03:16:53 bobr kernel: sdd: Write Protect is off
Aug 13 03:16:54 bobr kernel: sdd: Mode Sense: 00 3a 00 00
Aug 13 03:16:54 bobr kernel: SCSI device sdd: drive cache: write back
Aug 13 03:17:28 bobr kernel: ata4.00: exception Emask 0x0 SAct 0x0 SErr
0x180000 action 0x2 frozen
Aug 13 03:17:28 bobr kernel: ata4.00: (BMDMA stat 0x21)
Aug 13 03:17:28 bobr kernel: ata4.00: tag 0 cmd 0x35 Emask 0x4 stat 0x40 err
0x0 (timeout)
Aug 13 03:17:35 bobr kernel: ata4: port is slow to respond, please be patient
Aug 13 03:17:59 bobr kernel: ata4: port failed to respond (30 secs)
Aug 13 03:17:59 bobr kernel: ata4: soft resetting port
Aug 13 03:17:59 bobr kernel: ata4: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Aug 13 03:17:59 bobr kernel: ata4.00: configured for UDMA/100
Aug 13 03:17:59 bobr kernel: ata4: EH complete
Aug 13 03:18:00 bobr kernel: SCSI device sdd: 625142448 512-byte hdwr sectors
(320073 MB)
Aug 13 03:18:00 bobr kernel: sdd: Write Protect is off
Aug 13 03:18:00 bobr kernel: sdd: Mode Sense: 00 3a 00 00
Aug 13 03:18:00 bobr kernel: SCSI device sdd: drive cache: write back
2.6.23-rc2 (HD401LJ NCQ BLACKLISTED!!!):
Aug 12 23:39:54 bobr kernel: ata5: timeout waiting for ADMA IDLE, stat=0x440
Aug 12 23:39:54 bobr kernel: ata5.00: exception Emask 0x1 SAct 0x0 SErr
0x380000 action 0x2
Aug 12 23:39:54 bobr kernel: ata5.00: CPB resp_flags 0x11: , CMD error
Aug 12 23:39:54 bobr kernel: ata5.00: cmd 25/00:d0:f9:6c:b9/00:01:17:00:00/e0
tag 0 cdb 0x0 data 237568 in
Aug 12 23:39:54 bobr kernel: res 51/84:df:ea:6d:b9/84:00:17:00:00/e0
Emask 0x10 (ATA bus error)
Aug 12 23:39:54 bobr kernel: ata5: soft resetting port
Aug 12 23:39:55 bobr kernel: ata5: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Aug 12 23:39:55 bobr kernel: ata5.00: configured for UDMA/133
Aug 12 23:39:55 bobr kernel: ata5: EH complete
Aug 12 23:39:55 bobr kernel: sd 4:0:0:0: [sde] 781422768 512-byte hardware
sectors (400088 MB)
Aug 12 23:39:55 bobr kernel: sd 4:0:0:0: [sde] Write Protect is off
Aug 12 23:39:55 bobr kernel: sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
Aug 12 23:39:56 bobr kernel: sd 4:0:0:0: [sde] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Aug 12 23:40:46 bobr kernel: t. Dev: usb-0000:00:02.0-6/input0, Type: 2, Code:
1, Value: 1
Aug 12 23:40:47 bobr kernel: ata5: EH in ADMA mode, notifier 0x0
notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x0 next cpb
idx 0x0
Aug 12 23:40:47 bobr kernel: ata5: CPB 0: ctl_flags 0xd, resp_flags 0x0
Aug 12 23:40:47 bobr kernel: ata5: timeout waiting for ADMA IDLE, stat=0x400
Aug 12 23:40:47 bobr kernel: ata5: timeout waiting for ADMA LEGACY, stat=0x400
Aug 12 23:40:47 bobr kernel: ata5: limiting SATA link speed to 1.5 Gbps
Aug 12 23:40:47 bobr kernel: ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x6 frozen
Aug 12 23:40:47 bobr kernel: ata5.00: cmd 25/00:00:79:76:a3/00:02:17:00:00/e0
tag 0 cdb 0x0 data 262144 in
Aug 12 23:40:47 bobr kernel: res 40/00:8f:ba:10:a0/84:01:17:00:00/e0
Emask 0x4 (timeout)
Aug 12 23:40:47 bobr kernel: ata5: hard resetting port
Aug 12 23:40:47 bobr kernel: ata5: SATA link up 1.5 Gbps (SStatus 113 SControl
310)
Aug 12 23:40:47 bobr kernel: ata5.00: configured for UDMA/133
Aug 12 23:40:47 bobr kernel: ata5: EH complete
Aug 12 23:40:47 bobr kernel: sd 4:0:0:0: [sde] 781422768 512-byte hardware
sectors (400088 MB)
Aug 12 23:40:48 bobr kernel: sd 4:0:0:0: [sde] Write Protect is off
Aug 12 23:40:48 bobr kernel: sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
Aug 12 23:40:48 bobr kernel: sd 4:0:0:0: [sde] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
There is no connectors and power errors, i try to use many cables and bug is
present. When I try to disable HD401LJ, I see the same bug on WD HDDs on
ata1,2,3,4.... =(
I think, it's a sata_nv or sil3114 driver bug, in this mailing lists there are
many same problems with this chipset.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: regression problem with Maxtor disk
2007-08-12 14:14 regression problem with Maxtor disk Lieven Marchand
@ 2007-08-14 9:50 ` Tejun Heo
2007-08-14 23:14 ` Robert Hancock
0 siblings, 1 reply; 8+ messages in thread
From: Tejun Heo @ 2007-08-14 9:50 UTC (permalink / raw)
To: Lieven Marchand; +Cc: jgarzik, linux-ide, Robert Hancock
[cc'ing Robert Hancock and quoting the whole message for him]
Lieven Marchand wrote:
> Hi,
>
> the following drive
>
> Aug 12 12:26:15 black kernel: Vendor: ATA Model: Maxtor 7H500F0 Rev:
> HA43
> Aug 12 12:26:15 black kernel: Type: Direct-Access ANSI
> SCSI revision: 05
>
> works fine under 2.6.18 and crashes the boot procedure under
> 2.6.22. Occasionally the boot continues but most of the times the
> kernel crashes with an error message of a corrupt cpu context.
>
> I've added the logs of a succesful boot here. When such a boot
> succeeds, the system is noticeably slower than under 2.6.18.
>
> Aug 11 10:27:51 black kernel: scsi 4:0:0:0: Direct-Access ATA Maxtor 7H
> 500F0 HA43 PQ: 0 ANSI: 5
> Aug 11 10:27:51 black kernel: ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment bou
> ndary 0xFFFFFFFF, hw segs 61
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x440
> Aug 11 10:27:51 black kernel: res 51/04:00:00:00:00/04:00:00:00:00/40 E
> mask 0x1 (device error)
> Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
> Aug 11 10:27:51 black kernel: ata2: EH complete
>
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x440
> Aug 11 10:27:51 black kernel: res 51/04:00:00:00:00/04:00:00:00:00/40 E
> mask 0x1 (device error)
> Aug 11 10:27:51 black last message repeated 2 times
> Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
> Aug 11 10:27:51 black kernel: ata2: EH complete
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and ID
> LE, stat=0x440
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
> Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 E
> mask 0x4 (timeout)
> Aug 11 10:27:51 black last message repeated 2 times
> Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 E
> mask 0x4 (timeout)
> Aug 11 10:27:51 black kernel: ata2: soft resetting port
> Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
> 300)
> Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
> Aug 11 10:27:51 black kernel: ata2: EH complete
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and ID
> LE, stat=0x400
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
> Aug 11 10:27:51 black kernel: ata2.00: NCQ disabled due to excessive errors
> Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 E
> mask 0x4 (timeout)
> Aug 11 10:27:51 black last message repeated 2 times
> Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 E
> mask 0x4 (timeout)
> Aug 11 10:27:51 black kernel: ata2: soft resetting port
> Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
> 300)
> Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
> Aug 11 10:27:51 black kernel: ata2: EH complete
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and ID
> LE, stat=0x400
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
> Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 E
> mask 0x4 (timeout)
> Aug 11 10:27:51 black kernel: ata2: soft resetting port
> Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
> 300)
> Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
> Aug 11 10:27:51 black kernel: ata2: EH complete
> -
> To unsubscribe from this list: send the line "unsubscribe linux-ide" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
tejun
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: regression problem with Maxtor disk
2007-08-14 9:50 ` Tejun Heo
@ 2007-08-14 23:14 ` Robert Hancock
2007-08-15 7:34 ` Lieven Marchand
0 siblings, 1 reply; 8+ messages in thread
From: Robert Hancock @ 2007-08-14 23:14 UTC (permalink / raw)
To: Tejun Heo; +Cc: Lieven Marchand, jgarzik, linux-ide
Tejun Heo wrote:
> [cc'ing Robert Hancock and quoting the whole message for him]
>
> Lieven Marchand wrote:
>> Hi,
>>
>> the following drive
>>
>> Aug 12 12:26:15 black kernel: Vendor: ATA Model: Maxtor 7H500F0 Rev:
>> HA43
>> Aug 12 12:26:15 black kernel: Type: Direct-Access ANSI
>> SCSI revision: 05
>>
>> works fine under 2.6.18 and crashes the boot procedure under
>> 2.6.22. Occasionally the boot continues but most of the times the
>> kernel crashes with an error message of a corrupt cpu context.
>>
>> I've added the logs of a succesful boot here. When such a boot
>> succeeds, the system is noticeably slower than under 2.6.18.
>>
>> Aug 11 10:27:51 black kernel: scsi 4:0:0:0: Direct-Access ATA Maxtor 7H
>> 500F0 HA43 PQ: 0 ANSI: 5
>> Aug 11 10:27:51 black kernel: ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment bou
>> ndary 0xFFFFFFFF, hw segs 61
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x440
>> Aug 11 10:27:51 black kernel: res 51/04:00:00:00:00/04:00:00:00:00/40 E
>> mask 0x1 (device error)
>> Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
>> Aug 11 10:27:51 black kernel: ata2: EH complete
>>
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x440
>> Aug 11 10:27:51 black kernel: res 51/04:00:00:00:00/04:00:00:00:00/40 E
>> mask 0x1 (device error)
>> Aug 11 10:27:51 black last message repeated 2 times
>> Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
>> Aug 11 10:27:51 black kernel: ata2: EH complete
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and ID
>> LE, stat=0x440
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
>> Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 E
>> mask 0x4 (timeout)
>> Aug 11 10:27:51 black last message repeated 2 times
>> Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 E
>> mask 0x4 (timeout)
>> Aug 11 10:27:51 black kernel: ata2: soft resetting port
>> Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
>> 300)
>> Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
>> Aug 11 10:27:51 black kernel: ata2: EH complete
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and ID
>> LE, stat=0x400
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
>> Aug 11 10:27:51 black kernel: ata2.00: NCQ disabled due to excessive errors
>> Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 E
>> mask 0x4 (timeout)
>> Aug 11 10:27:51 black last message repeated 2 times
>> Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 E
>> mask 0x4 (timeout)
>> Aug 11 10:27:51 black kernel: ata2: soft resetting port
>> Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
>> 300)
>> Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
>> Aug 11 10:27:51 black kernel: ata2: EH complete
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and ID
>> LE, stat=0x400
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
>> Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
>> Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 E
>> mask 0x4 (timeout)
>> Aug 11 10:27:51 black kernel: ata2: soft resetting port
>> Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
>> 300)
>> Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
>> Aug 11 10:27:51 black kernel: ata2: EH complete
It looks like there are some lines missing from this log, there should
be a line before the "res" lines indicating what the failed command was..
My guess, though, is that NCQ is somehow busted on this drive, as is
known to be the case with a number of other Maxtor disks..
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: regression problem with Maxtor disk
2007-08-14 23:14 ` Robert Hancock
@ 2007-08-15 7:34 ` Lieven Marchand
2007-08-15 7:53 ` Tejun Heo
0 siblings, 1 reply; 8+ messages in thread
From: Lieven Marchand @ 2007-08-15 7:34 UTC (permalink / raw)
To: Robert Hancock; +Cc: Tejun Heo, jgarzik, linux-ide
Robert Hancock <hancockr@shaw.ca> writes:
> It looks like there are some lines missing from this log, there should
> be a line before the "res" lines indicating what the failed command
> was..
There isn't. I snipped some irrelevant stuff but nothing about a
command. The full log is appended.
> My guess, though, is that NCQ is somehow busted on this drive, as is
> known to be the case with a number of other Maxtor disks..
Aug 11 10:27:51 black kernel: sata_nv 0000:00:07.0: Using ADMA mode
Aug 11 10:27:51 black kernel: scsi3 : sata_nv
Aug 11 10:27:51 black kernel: scsi4 : sata_nv
Aug 11 10:27:51 black kernel: ata1: SATA max UDMA/133 cmd 0xf8840480 ctl 0xf88404a0 bmdma 0x0001cc00 irq 19
Aug 11 10:27:51 black kernel: ata2: SATA max UDMA/133 cmd 0xf8840580 ctl 0xf88405a0 bmdma 0x0001cc08 irq 19
Aug 11 10:27:51 black kernel: hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Aug 11 10:27:51 black kernel: Uniform CD-ROM driver Revision: 3.20
Aug 11 10:27:51 black kernel: hdb: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66)
Aug 11 10:27:51 black kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 11 10:27:51 black kernel: ata1.00: ATA-7: MAXTOR STM3320820AS, 3.AAE, max UDMA/133
Aug 11 10:27:51 black kernel: ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 11 10:27:51 black kernel: ata1.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 11 10:27:51 black kernel: ata2.00: ATA-7: Maxtor 7H500F0, HA431DN0, max UDMA/133
Aug 11 10:27:51 black kernel: ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: scsi 3:0:0:0: Direct-Access ATA MAXTOR STM332082 3.AA PQ: 0 ANSI: 5
Aug 11 10:27:51 black kernel: ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
Aug 11 10:27:51 black kernel: scsi 4:0:0:0: Direct-Access ATA Maxtor 7H500F0 HA43 PQ: 0 ANSI: 5
Aug 11 10:27:51 black kernel: ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
Aug 11 10:27:51 black kernel: ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 23
Aug 11 10:27:51 black kernel: ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 23 (level, low) -> IRQ 16
Aug 11 10:27:51 black kernel: sata_nv 0000:00:08.0: Using ADMA mode
Aug 11 10:27:51 black kernel: scsi5 : sata_nv
Aug 11 10:27:51 black kernel: scsi6 : sata_nv
Aug 11 10:27:51 black kernel: ata3: SATA max UDMA/133 cmd 0xf88de480 ctl 0xf88de4a0 bmdma 0x0001b800 irq 16
Aug 11 10:27:51 black kernel: ata4: SATA max UDMA/133 cmd 0xf88de580 ctl 0xf88de5a0 bmdma 0x0001b808 irq 16
Aug 11 10:27:51 black kernel: ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 11 10:27:51 black kernel: ata3.00: ATA-7: Maxtor 6Y200M0, YAR51HW0, max UDMA/133
Aug 11 10:27:51 black kernel: ata3.00: 398297088 sectors, multi 16: LBA48
Aug 11 10:27:51 black kernel: ata3.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 11 10:27:51 black kernel: ata4.00: ATA-7: Maxtor 6B300S0, BANC1980, max UDMA/133
Aug 11 10:27:51 black kernel: ata4.00: 586114704 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 11 10:27:51 black kernel: ata4.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: scsi 5:0:0:0: Direct-Access ATA Maxtor 6Y200M0 YAR5 PQ: 0 ANSI: 5
Aug 11 10:27:51 black kernel: ata3: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
Aug 11 10:27:51 black kernel: scsi 6:0:0:0: Direct-Access ATA Maxtor 6B300S0 BANC PQ: 0 ANSI: 5
Aug 11 10:27:51 black kernel: ata4: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
Aug 11 10:27:51 black kernel: sd 3:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
Aug 11 10:27:51 black kernel: sd 3:0:0:0: [sda] Write Protect is off
Aug 11 10:27:51 black kernel: sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: sd 3:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
Aug 11 10:27:51 black kernel: sd 3:0:0:0: [sda] Write Protect is off
Aug 11 10:27:51 black kernel: sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: sda: sda1
Aug 11 10:27:51 black kernel: sd 3:0:0:0: [sda] Attached SCSI disk
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write Protect is off
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write Protect is off
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: sdb: sdb1 sdb2 < sdb5 sdb6 >
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Attached SCSI disk
Aug 11 10:27:51 black kernel: sd 5:0:0:0: [sdc] 398297088 512-byte hardware sectors (203928 MB)
Aug 11 10:27:51 black kernel: sd 5:0:0:0: [sdc] Write Protect is off
Aug 11 10:27:51 black kernel: sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: sd 5:0:0:0: [sdc] 398297088 512-byte hardware sectors (203928 MB)
Aug 11 10:27:51 black kernel: sd 5:0:0:0: [sdc] Write Protect is off
Aug 11 10:27:51 black kernel: sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: sdc: sdc1 sdc2 sdc3 < sdc5 sdc6 >
Aug 11 10:27:51 black kernel: sd 5:0:0:0: [sdc] Attached SCSI disk
Aug 11 10:27:51 black kernel: sd 6:0:0:0: [sdd] 586114704 512-byte hardware sectors (300091 MB)
Aug 11 10:27:51 black kernel: sd 6:0:0:0: [sdd] Write Protect is off
Aug 11 10:27:51 black kernel: sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: sd 6:0:0:0: [sdd] 586114704 512-byte hardware sectors (300091 MB)
Aug 11 10:27:51 black kernel: sd 6:0:0:0: [sdd] Write Protect is off
Aug 11 10:27:51 black kernel: sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: sdd: sdd1 sdd2
Aug 11 10:27:51 black kernel: sd 6:0:0:0: [sdd] Attached SCSI disk
Aug 11 10:27:51 black kernel: device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Aug 11 10:27:51 black kernel: kjournald starting. Commit interval 5 seconds
Aug 11 10:27:51 black kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 11 10:27:51 black kernel: scsi 1:0:0:0: Direct-Access Seagate External Drive PQ: 0 ANSI: 0
Aug 11 10:27:51 black kernel: scsi 0:0:0:0: Direct-Access USB 2.0 Storage Device 0100 PQ: 0 ANSI: 0 CCS
Aug 11 10:27:51 black kernel: sd 0:0:0:0: [sde] 320173056 512-byte hardware sectors (163929 MB)
Aug 11 10:27:51 black kernel: sd 0:0:0:0: [sde] Write Protect is off
Aug 11 10:27:51 black kernel: sd 0:0:0:0: [sde] 320173056 512-byte hardware sectors (163929 MB)
Aug 11 10:27:51 black kernel: scsi 2:0:0:0: Direct-Access ST332082 0A 3.AA PQ: 0 ANSI: 0
Aug 11 10:27:51 black kernel: sd 0:0:0:0: [sde] Write Protect is off
Aug 11 10:27:51 black kernel: sde: sde1
Aug 11 10:27:51 black kernel: sd 0:0:0:0: [sde] Attached SCSI disk
Aug 11 10:27:51 black kernel: sd 2:0:0:0: [sdf] 625142448 512-byte hardware sectors (320073 MB)
Aug 11 10:27:51 black kernel: sd 2:0:0:0: [sdf] Write Protect is off
Aug 11 10:27:51 black kernel: sd 2:0:0:0: [sdf] 625142448 512-byte hardware sectors (320073 MB)
Aug 11 10:27:51 black kernel: sd 2:0:0:0: [sdf] Write Protect is off
Aug 11 10:27:51 black kernel: sdf:<6>i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
Aug 11 10:27:51 black kernel: i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
Aug 11 10:27:51 black kernel: input: PC Speaker as /class/input/input1
Aug 11 10:27:51 black kernel: Real Time Clock Driver v1.12ac
Aug 11 10:27:51 black kernel: ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
Aug 11 10:27:51 black kernel: ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, low) -> IRQ 17
Aug 11 10:27:51 black kernel: NET: Registered protocol family 23
Aug 11 10:27:51 black kernel: intel8x0_measure_ac97_clock: measured 54821 usecs
Aug 11 10:27:51 black kernel: intel8x0: clocking to 46989
Aug 11 10:27:51 black kernel: input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
Aug 11 10:27:51 black kernel: parport_pc 00:0a: reported by Plug and Play ACPI
Aug 11 10:27:51 black kernel: parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Aug 11 10:27:51 black kernel: sdf1
Aug 11 10:27:51 black kernel: sd 2:0:0:0: [sdf] Attached SCSI disk
Aug 11 10:27:51 black kernel: sd 1:0:0:0: [sdg] 312581808 512-byte hardware sectors (160042 MB)
Aug 11 10:27:51 black kernel: sd 1:0:0:0: [sdg] Write Protect is off
Aug 11 10:27:51 black kernel: sd 1:0:0:0: [sdg] 312581808 512-byte hardware sectors (160042 MB)
Aug 11 10:27:51 black kernel: sd 1:0:0:0: [sdg] Write Protect is off
Aug 11 10:27:51 black kernel: sdg: sdg1 sdg2 sdg3
Aug 11 10:27:51 black kernel: sd 1:0:0:0: [sdg] Attached SCSI disk
Aug 11 10:27:51 black kernel: Adding 3036244k swap on /dev/sdb5. Priority:-1 extents:1 across:3036244k
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x440
Aug 11 10:27:51 black kernel: res 51/04:00:00:00:00/04:00:00:00:00/40 Emask 0x1 (device error)
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: EH complete
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write Protect is off
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: EXT3 FS on dm-0, internal journal
Aug 11 10:27:51 black kernel: kjournald starting. Commit interval 5 seconds
Aug 11 10:27:51 black kernel: EXT3 FS on sdb1, internal journal
Aug 11 10:27:51 black kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 11 10:27:51 black kernel: kjournald starting. Commit interval 5 seconds
Aug 11 10:27:51 black kernel: EXT3 FS on dm-4, internal journal
Aug 11 10:27:51 black kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 11 10:27:51 black kernel: kjournald starting. Commit interval 5 seconds
Aug 11 10:27:51 black kernel: EXT3 FS on dm-3, internal journal
Aug 11 10:27:51 black kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 11 10:27:51 black kernel: kjournald starting. Commit interval 5 seconds
Aug 11 10:27:51 black kernel: EXT3 FS on dm-1, internal journal
Aug 11 10:27:51 black kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 11 10:27:51 black kernel: kjournald starting. Commit interval 5 seconds
Aug 11 10:27:51 black kernel: EXT3 FS on dm-2, internal journal
Aug 11 10:27:51 black kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 11 10:27:51 black kernel: kjournald starting. Commit interval 5 seconds
Aug 11 10:27:51 black kernel: EXT3 FS on sdd1, internal journal
Aug 11 10:27:51 black kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 11 10:27:51 black kernel: kjournald starting. Commit interval 5 seconds
Aug 11 10:27:51 black kernel: EXT3 FS on sda1, internal journal
Aug 11 10:27:51 black kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 11 10:27:51 black kernel: kjournald starting. Commit interval 5 seconds
Aug 11 10:27:51 black kernel: EXT3 FS on sdd2, internal journal
Aug 11 10:27:51 black kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x440
Aug 11 10:27:51 black kernel: res 51/04:00:00:00:00/04:00:00:00:00/40 Emask 0x1 (device error)
Aug 11 10:27:51 black last message repeated 2 times
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: EH complete
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x440
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write Protect is off
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 Emask 0x4 (timeout)
Aug 11 10:27:51 black last message repeated 2 times
Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Aug 11 10:27:51 black kernel: ata2: soft resetting port
Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: EH complete
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x400
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write Protect is off
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
Aug 11 10:27:51 black kernel: ata2.00: NCQ disabled due to excessive errors
Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 Emask 0x4 (timeout)
Aug 11 10:27:51 black last message repeated 2 times
Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Aug 11 10:27:51 black kernel: ata2: soft resetting port
Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: EH complete
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x400
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA IDLE, stat=0x400
Aug 11 10:27:51 black kernel: ata2: timeout waiting for ADMA LEGACY, stat=0x400
Aug 11 10:27:51 black kernel: res 40/00:00:00:00:00/04:00:00:00:00/40 Emask 0x4 (timeout)
Aug 11 10:27:51 black kernel: ata2: soft resetting port
Aug 11 10:27:51 black kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 11 10:27:51 black kernel: ata2.00: configured for UDMA/133
Aug 11 10:27:51 black kernel: ata2: EH complete
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write Protect is off
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write Protect is off
Aug 11 10:27:51 black kernel: sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Aug 11 10:27:51 black kernel: input: Power Button (FF) as /class/input/input3
Aug 11 10:27:51 black kernel: ACPI: Power Button (FF) [PWRF]
Aug 11 10:27:51 black kernel: input: Power Button (CM) as /class/input/input4
Aug 11 10:27:51 black kernel: ACPI: Power Button (CM) [PWRB]
Aug 11 10:27:53 black kernel: NET: Registered protocol family 10
Aug 11 10:27:53 black kernel: lo: Disabled Privacy Extensions
Aug 11 10:28:35 black kernel: Linux agpgart interface v0.102 (c) Dave Jones
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: regression problem with Maxtor disk
2007-08-15 7:34 ` Lieven Marchand
@ 2007-08-15 7:53 ` Tejun Heo
2007-08-15 21:22 ` Lieven Marchand
0 siblings, 1 reply; 8+ messages in thread
From: Tejun Heo @ 2007-08-15 7:53 UTC (permalink / raw)
To: Lieven Marchand; +Cc: Robert Hancock, jgarzik, linux-ide
Lieven Marchand wrote:
> Robert Hancock <hancockr@shaw.ca> writes:
>
>> It looks like there are some lines missing from this log, there should
>> be a line before the "res" lines indicating what the failed command
>> was..
>
> There isn't. I snipped some irrelevant stuff but nothing about a
> command. The full log is appended.
It seems klogd clipped some messages. Can you please turn on printk
timestamp, enlarge printk log buffersize and post the result of 'dmesg'
after errors?
--
tejun
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: regression problem with Maxtor disk
2007-08-15 7:53 ` Tejun Heo
@ 2007-08-15 21:22 ` Lieven Marchand
2007-08-15 23:31 ` Robert Hancock
0 siblings, 1 reply; 8+ messages in thread
From: Lieven Marchand @ 2007-08-15 21:22 UTC (permalink / raw)
To: Tejun Heo; +Cc: Robert Hancock, jgarzik, linux-ide
Tejun Heo <htejun@gmail.com> writes:
> It seems klogd clipped some messages. Can you please turn on printk
> timestamp, enlarge printk log buffersize and post the result of 'dmesg'
> after errors?
[ 33.587986] libata version 2.21 loaded.
[ 33.592361] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
[ 33.592411] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 18
[ 33.592508] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 33.592516] forcedeth: using HIGHDMA
[ 33.633334] hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 33.633558] Uniform CD-ROM driver Revision: 3.20
[ 33.638683] hdb: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66)
[ 34.109811] eth0: forcedeth.c: subsystem: 01695:1010 bound to 0000:00:0a.0
[ 34.109949] sata_nv 0000:00:07.0: version 3.4
[ 34.110368] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20
[ 34.110414] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 20 (level, low) -> IRQ 19
[ 34.110509] sata_nv 0000:00:07.0: Using ADMA mode
[ 34.110587] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 34.110849] scsi0 : sata_nv
[ 34.110922] scsi1 : sata_nv
[ 34.110973] ata1: SATA max UDMA/133 cmd 0xf883e480 ctl 0xf883e4a0 bmdma 0x0001cc00 irq 19
[ 34.111026] ata2: SATA max UDMA/133 cmd 0xf883e580 ctl 0xf883e5a0 bmdma 0x0001cc08 irq 19
[ 34.129549] usb 2-1: new high speed USB device using ehci_hcd and address 2
[ 34.322380] usb 2-1: configuration #1 chosen from 1 choice
[ 34.336790] Initializing USB Mass Storage driver...
[ 34.560984] usb 2-2: new high speed USB device using ehci_hcd and address 3
[ 34.576963] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 34.586151] ata1.00: ATA-7: Maxtor 7H500F0, HA431DN0, max UDMA/133
[ 34.586191] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 34.602085] ata1.00: configured for UDMA/133
[ 34.695412] usb 2-2: configuration #1 chosen from 1 choice
[ 34.932499] usb 2-4: new high speed USB device using ehci_hcd and address 4
[ 35.068325] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 35.116969] ata2.00: ATA-7: MAXTOR STM3320820AS, 3.AAE, max UDMA/133
[ 35.117010] ata2.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 35.147355] usb 2-4: configuration #1 chosen from 1 choice
[ 35.149712] scsi2 : SCSI emulation for USB Mass Storage devices
[ 35.149993] usb-storage: device found at 2
[ 35.149995] usb-storage: waiting for device to settle before scanning
[ 35.150009] scsi3 : SCSI emulation for USB Mass Storage devices
[ 35.150201] usb-storage: device found at 3
[ 35.150203] usb-storage: waiting for device to settle before scanning
[ 35.150216] scsi4 : SCSI emulation for USB Mass Storage devices
[ 35.150406] usbcore: registered new interface driver usb-storage
[ 35.150447] USB Mass Storage support registered.
[ 35.150491] usb-storage: device found at 4
[ 35.150493] usb-storage: waiting for device to settle before scanning
[ 35.183534] ata2.00: configured for UDMA/133
[ 35.183676] scsi 0:0:0:0: Direct-Access ATA Maxtor 7H500F0 HA43 PQ: 0 ANSI: 5
[ 35.183734] ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
[ 35.184076] scsi 1:0:0:0: Direct-Access ATA MAXTOR STM332082 3.AA PQ: 0 ANSI: 5
[ 35.184130] ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
[ 35.184627] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 23
[ 35.184668] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 23 (level, low) -> IRQ 16
[ 35.184764] sata_nv 0000:00:08.0: Using ADMA mode
[ 35.184843] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 35.184933] scsi5 : sata_nv
[ 35.184996] scsi6 : sata_nv
[ 35.185050] ata3: SATA max UDMA/133 cmd 0xf88a0480 ctl 0xf88a04a0 bmdma 0x0001b800 irq 16
[ 35.185102] ata4: SATA max UDMA/133 cmd 0xf88a0580 ctl 0xf88a05a0 bmdma 0x0001b808 irq 16
[ 35.651571] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 35.660568] ata3.00: ATA-7: Maxtor 6B300S0, BANC1980, max UDMA/133
[ 35.660608] ata3.00: 586114704 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 35.676553] ata3.00: configured for UDMA/133
[ 35.987125] ata4: SATA link down (SStatus 0 SControl 300)
[ 35.987235] scsi 5:0:0:0: Direct-Access ATA Maxtor 6B300S0 BANC PQ: 0 ANSI: 5
[ 35.987289] ata3: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
[ 36.023244] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 36.023297] sd 0:0:0:0: [sda] Write Protect is off
[ 36.023336] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 36.023347] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 36.023439] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 36.023484] sd 0:0:0:0: [sda] Write Protect is off
[ 36.023522] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 36.023531] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 36.023584] sda: sda1 sda2 < sda5 sda6 sda7 >
[ 36.075908] sd 0:0:0:0: [sda] Attached SCSI disk
[ 36.076642] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 36.078107] sd 1:0:0:0: [sdb] Write Protect is off
[ 36.078145] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 36.078155] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 36.078230] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 36.078274] sd 1:0:0:0: [sdb] Write Protect is off
[ 36.078312] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 36.078322] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 36.078374] sdb: sdb1
[ 36.096793] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 36.097148] sd 5:0:0:0: [sdc] 586114704 512-byte hardware sectors (300091 MB)
[ 36.097193] sd 5:0:0:0: [sdc] Write Protect is off
[ 36.097231] sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 36.097241] sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 36.097318] sd 5:0:0:0: [sdc] 586114704 512-byte hardware sectors (300091 MB)
[ 36.097363] sd 5:0:0:0: [sdc] Write Protect is off
[ 36.097401] sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 36.097410] sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 36.097462] sdc: sdc1 sdc2
[ 36.116596] sd 5:0:0:0: [sdc] Attached SCSI disk
[ 36.488949] Probing IDE interface ide1...
[ 37.067405] md: raid1 personality registered for level 1
[ 37.082723] md: md0 stopped.
[ 37.112993] md: bind<sdc2>
[ 37.113130] md: bind<sda7>
[ 37.123391] raid1: raid set md0 active with 2 out of 2 mirrors
[ 37.302653] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 37.905627] kjournald starting. Commit interval 5 seconds
[ 37.905678] EXT3-fs: mounted filesystem with ordered data mode.
[ 39.355192] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
[ 39.355256] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
[ 40.023669] Real Time Clock Driver v1.12ac
[ 40.047120] input: PC Speaker as /class/input/input1
[ 40.079840] irda_init()
[ 40.079860] NET: Registered protocol family 23
[ 40.108430] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
[ 40.108475] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, low) -> IRQ 17
[ 40.108588] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 40.141895] usb-storage: device scan complete
[ 40.142136] usb-storage: device scan complete
[ 40.142171] usb-storage: device scan complete
[ 40.144889] scsi 3:0:0:0: Direct-Access Seagate External Drive PQ: 0 ANSI: 0
[ 40.157610] scsi 2:0:0:0: Direct-Access USB 2.0 Storage Device 0100 PQ: 0 ANSI: 0 CCS
[ 40.163346] sd 2:0:0:0: [sdd] 320173056 512-byte hardware sectors (163929 MB)
[ 40.165091] sd 2:0:0:0: [sdd] Write Protect is off
[ 40.165129] sd 2:0:0:0: [sdd] Mode Sense: 08 00 00 00
[ 40.165132] sd 2:0:0:0: [sdd] Assuming drive cache: write through
[ 40.170335] sd 2:0:0:0: [sdd] 320173056 512-byte hardware sectors (163929 MB)
[ 40.172150] sd 2:0:0:0: [sdd] Write Protect is off
[ 40.172188] sd 2:0:0:0: [sdd] Mode Sense: 08 00 00 00
[ 40.172190] sd 2:0:0:0: [sdd] Assuming drive cache: write through
[ 40.172230] sdd:<5>scsi 4:0:0:0: Direct-Access ST332082 0A 3.AA PQ: 0 ANSI: 0
[ 40.181832] sdd1
[ 40.181923] sd 2:0:0:0: [sdd] Attached SCSI disk
[ 40.184193] sd 4:0:0:0: [sde] 625142448 512-byte hardware sectors (320073 MB)
[ 40.187065] sd 4:0:0:0: [sde] Write Protect is off
[ 40.187103] sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
[ 40.187105] sd 4:0:0:0: [sde] Assuming drive cache: write through
[ 40.189186] sd 4:0:0:0: [sde] 625142448 512-byte hardware sectors (320073 MB)
[ 40.191059] sd 4:0:0:0: [sde] Write Protect is off
[ 40.191097] sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
[ 40.191099] sd 4:0:0:0: [sde] Assuming drive cache: write through
[ 40.191138] sde:<6>intel8x0_measure_ac97_clock: measured 54811 usecs
[ 40.429398] intel8x0: clocking to 46981
[ 40.919334] input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
[ 40.922844] parport_pc 00:0a: reported by Plug and Play ACPI
[ 40.922929] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 43.511331] Adding 3036244k swap on /dev/sda5. Priority:-1 extents:1 across:3036244k
[ 43.952498] EXT3 FS on dm-0, internal journal
[ 44.020016] sde1
[ 44.020140] sd 4:0:0:0: [sde] Attached SCSI disk
[ 44.025003] sd 3:0:0:0: [sdf] 312581808 512-byte hardware sectors (160042 MB)
[ 44.028710] sd 3:0:0:0: [sdf] Write Protect is off
[ 44.028756] sd 3:0:0:0: [sdf] Mode Sense: 27 00 00 00
[ 44.028759] sd 3:0:0:0: [sdf] Assuming drive cache: write through
[ 44.032707] sd 3:0:0:0: [sdf] 312581808 512-byte hardware sectors (160042 MB)
[ 44.035706] sd 3:0:0:0: [sdf] Write Protect is off
[ 44.035745] sd 3:0:0:0: [sdf] Mode Sense: 27 00 00 00
[ 44.035748] sd 3:0:0:0: [sdf] Assuming drive cache: write through
[ 44.035788] sdf: sdf1 sdf2 sdf3
[ 44.057279] sd 3:0:0:0: [sdf] Attached SCSI disk
[ 44.417152] f71805f: Found F71872F/FG chip at 0x290, revision 33
[ 48.251624] kjournald starting. Commit interval 5 seconds
[ 48.301077] EXT3 FS on dm-4, internal journal
[ 48.301138] EXT3-fs: mounted filesystem with ordered data mode.
[ 48.315828] kjournald starting. Commit interval 5 seconds
[ 48.324360] EXT3 FS on dm-3, internal journal
[ 48.324419] EXT3-fs: mounted filesystem with ordered data mode.
[ 48.351268] kjournald starting. Commit interval 5 seconds
[ 48.361585] EXT3 FS on dm-1, internal journal
[ 48.361644] EXT3-fs: mounted filesystem with ordered data mode.
[ 48.393085] kjournald starting. Commit interval 5 seconds
[ 48.399449] EXT3 FS on dm-2, internal journal
[ 48.399508] EXT3-fs: mounted filesystem with ordered data mode.
[ 48.422368] kjournald starting. Commit interval 5 seconds
[ 48.432338] EXT3 FS on sda1, internal journal
[ 48.432397] EXT3-fs: mounted filesystem with ordered data mode.
[ 48.454943] kjournald starting. Commit interval 5 seconds
[ 48.455094] EXT3 FS on sdc1, internal journal
[ 48.455152] EXT3-fs: mounted filesystem with ordered data mode.
[ 48.470571] kjournald starting. Commit interval 5 seconds
[ 48.475025] EXT3 FS on sdb1, internal journal
[ 48.475083] EXT3-fs: mounted filesystem with ordered data mode.
[ 48.501723] kjournald starting. Commit interval 5 seconds
[ 48.510507] EXT3 FS on sda6, internal journal
[ 48.510567] EXT3-fs: mounted filesystem with ordered data mode.
[ 48.994556] ata1: timeout waiting for ADMA IDLE, stat=0x440
[ 49.147577] ata1: failed to read log page 10h (errno=-2)
[ 49.149046] ata1.00: exception Emask 0x1 SAct 0xff SErr 0x0 action 0x0
[ 49.149086] ata1.00: (CPB resp_flags 0x11: CMD error)
[ 49.149129] ata1.00: cmd 61/06:00:bc:bf:df/00:00:16:00:00/40 tag 0 cdb 0x0 data 3072 out
[ 49.149131] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
[ 49.149234] ata1.00: cmd 61/04:08:c4:bf:df/00:00:16:00:00/40 tag 1 cdb 0x0 data 2048 out
[ 49.149236] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
[ 49.149338] ata1.00: cmd 61/02:10:d6:bf:df/00:00:16:00:00/40 tag 2 cdb 0x0 data 1024 out
[ 49.149340] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
[ 49.149443] ata1.00: cmd 61/04:18:dc:bf:df/00:00:16:00:00/40 tag 3 cdb 0x0 data 2048 out
[ 49.149445] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
[ 49.149547] ata1.00: cmd 61/02:20:e8:bf:df/00:00:16:00:00/40 tag 4 cdb 0x0 data 1024 out
[ 49.149549] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
[ 49.149652] ata1.00: cmd 61/02:28:f2:bf:df/00:00:16:00:00/40 tag 5 cdb 0x0 data 1024 out
[ 49.149653] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
[ 49.149756] ata1.00: cmd 61/04:30:fa:bf:df/00:00:16:00:00/40 tag 6 cdb 0x0 data 2048 out
[ 49.149758] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
[ 49.149860] ata1.00: cmd 61/02:38:04:c0:df/00:00:16:00:00/40 tag 7 cdb 0x0 data 1024 out
[ 49.149862] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
[ 49.175045] ata1.00: configured for UDMA/133
[ 49.175095] ata1: EH complete
[ 49.175145] ata1: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x440
[ 49.175237] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 49.175285] sd 0:0:0:0: [sda] Write Protect is off
[ 49.175323] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 49.175334] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 79.155040] ata1: EH in ADMA mode, notifier 0x0 notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x17 next cpb idx 0x0
[ 79.155098] ata1: CPB 0: ctl_flags 0x1f, resp_flags 0x2
[ 79.155136] ata1: CPB 1: ctl_flags 0x1f, resp_flags 0x0
[ 79.155174] ata1: CPB 2: ctl_flags 0x1f, resp_flags 0x0
[ 79.155212] ata1: CPB 3: ctl_flags 0x1f, resp_flags 0x0
[ 79.155250] ata1: CPB 4: ctl_flags 0x1f, resp_flags 0x0
[ 79.155288] ata1: CPB 5: ctl_flags 0x1f, resp_flags 0x0
[ 79.155326] ata1: CPB 6: ctl_flags 0x1f, resp_flags 0x0
[ 79.155364] ata1: CPB 7: ctl_flags 0x1f, resp_flags 0x0
[ 79.155402] ata1: CPB 8: ctl_flags 0x1f, resp_flags 0x0
[ 79.155440] ata1: CPB 9: ctl_flags 0x1f, resp_flags 0x0
[ 79.155478] ata1: CPB 10: ctl_flags 0x1f, resp_flags 0x0
[ 79.155517] ata1: CPB 11: ctl_flags 0x1f, resp_flags 0x0
[ 79.155555] ata1: CPB 12: ctl_flags 0x1f, resp_flags 0x0
[ 79.155593] ata1: CPB 13: ctl_flags 0x1f, resp_flags 0x0
[ 79.155631] ata1: CPB 14: ctl_flags 0x1f, resp_flags 0x0
[ 79.155669] ata1: CPB 15: ctl_flags 0x1f, resp_flags 0x0
[ 79.155708] ata1: CPB 16: ctl_flags 0x1f, resp_flags 0x0
[ 79.155746] ata1: CPB 17: ctl_flags 0x1f, resp_flags 0x0
[ 79.155784] ata1: CPB 18: ctl_flags 0x1f, resp_flags 0x0
[ 79.155828] ata1: timeout waiting for ADMA IDLE, stat=0x400
[ 79.155873] ata1: timeout waiting for ADMA LEGACY, stat=0x400
[ 79.155917] ata1.00: exception Emask 0x0 SAct 0x7ffff SErr 0x0 action 0x2 frozen
[ 79.155971] ata1.00: cmd 61/02:00:02:c1:df/00:00:16:00:00/40 tag 0 cdb 0x0 data 1024 out
[ 79.155973] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 79.156075] ata1.00: cmd 61/04:08:fa:bf:df/00:00:16:00:00/40 tag 1 cdb 0x0 data 2048 out
[ 79.156077] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 79.156179] ata1.00: cmd 61/02:10:f2:bf:df/00:00:16:00:00/40 tag 2 cdb 0x0 data 1024 out
[ 79.156180] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 79.156282] ata1.00: cmd 61/02:18:e8:bf:df/00:00:16:00:00/40 tag 3 cdb 0x0 data 1024 out
[ 79.156284] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 79.156386] ata1.00: cmd 61/04:20:dc:bf:df/00:00:16:00:00/40 tag 4 cdb 0x0 data 2048 out
[ 79.156388] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 79.156490] ata1.00: cmd 61/02:28:d6:bf:df/00:00:16:00:00/40 tag 5 cdb 0x0 data 1024 out
[ 79.156492] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 79.156594] ata1.00: cmd 61/04:30:c4:bf:df/00:00:16:00:00/40 tag 6 cdb 0x0 data 2048 out
[ 79.156596] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 79.156698] ata1.00: cmd 61/06:38:bc:bf:df/00:00:16:00:00/40 tag 7 cdb 0x0 data 3072 out
[ 79.156699] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 79.156801] ata1.00: cmd 61/04:40:08:c0:df/00:00:16:00:00/40 tag 8 cdb 0x0 data 2048 out
[ 79.156803] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.156905] ata1.00: cmd 61/04:48:ca:c0:df/00:00:16:00:00/40 tag 9 cdb 0x0 data 2048 out
[ 79.156907] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.157009] ata1.00: cmd 61/06:50:d0:c0:df/00:00:16:00:00/40 tag 10 cdb 0x0 data 3072 out
[ 79.157011] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.157113] ata1.00: cmd 61/02:58:d8:c0:df/00:00:16:00:00/40 tag 11 cdb 0x0 data 1024 out
[ 79.157114] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.157216] ata1.00: cmd 61/02:60:e0:c0:df/00:00:16:00:00/40 tag 12 cdb 0x0 data 1024 out
[ 79.157218] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.157320] ata1.00: cmd 61/02:68:f0:c0:df/00:00:16:00:00/40 tag 13 cdb 0x0 data 1024 out
[ 79.157322] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.157424] ata1.00: cmd 61/02:70:f8:c0:df/00:00:16:00:00/40 tag 14 cdb 0x0 data 1024 out
[ 79.157426] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.157528] ata1.00: cmd 61/04:78:fc:c0:df/00:00:16:00:00/40 tag 15 cdb 0x0 data 2048 out
[ 79.157529] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.157631] ata1.00: cmd 61/02:80:06:c1:df/00:00:16:00:00/40 tag 16 cdb 0x0 data 1024 out
[ 79.157633] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.157735] ata1.00: cmd 61/06:88:0a:c1:df/00:00:16:00:00/40 tag 17 cdb 0x0 data 3072 out
[ 79.157737] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.157839] ata1.00: cmd 61/04:90:18:c1:df/00:00:16:00:00/40 tag 18 cdb 0x0 data 2048 out
[ 79.157841] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 79.466629] ata1: soft resetting port
[ 79.622437] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 79.647445] ata1.00: configured for UDMA/133
[ 79.647494] ata1: EH complete
[ 79.647538] ata1: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x400
[ 79.647602] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 79.647648] sd 0:0:0:0: [sda] Write Protect is off
[ 79.647686] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 79.647697] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 109.607481] ata1: EH in ADMA mode, notifier 0x0 notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x12 next cpb idx 0x0
[ 109.607538] ata1: CPB 0: ctl_flags 0x1f, resp_flags 0x2
[ 109.607576] ata1: CPB 1: ctl_flags 0x1f, resp_flags 0x0
[ 109.607614] ata1: CPB 2: ctl_flags 0x1f, resp_flags 0x0
[ 109.607652] ata1: CPB 3: ctl_flags 0x1f, resp_flags 0x0
[ 109.607690] ata1: CPB 4: ctl_flags 0x1f, resp_flags 0x0
[ 109.607728] ata1: CPB 5: ctl_flags 0x1f, resp_flags 0x0
[ 109.607766] ata1: CPB 6: ctl_flags 0x1f, resp_flags 0x0
[ 109.607804] ata1: CPB 7: ctl_flags 0x1f, resp_flags 0x0
[ 109.607842] ata1: CPB 8: ctl_flags 0x1f, resp_flags 0x0
[ 109.607880] ata1: CPB 9: ctl_flags 0x1f, resp_flags 0x0
[ 109.607919] ata1: CPB 10: ctl_flags 0x1f, resp_flags 0x0
[ 109.607957] ata1: CPB 11: ctl_flags 0x1f, resp_flags 0x0
[ 109.607995] ata1: CPB 12: ctl_flags 0x1f, resp_flags 0x0
[ 109.608033] ata1: CPB 13: ctl_flags 0x1f, resp_flags 0x0
[ 109.608071] ata1: CPB 14: ctl_flags 0x1f, resp_flags 0x0
[ 109.608110] ata1: CPB 15: ctl_flags 0x1f, resp_flags 0x0
[ 109.608148] ata1: CPB 16: ctl_flags 0x1f, resp_flags 0x0
[ 109.608186] ata1: CPB 17: ctl_flags 0x1f, resp_flags 0x0
[ 109.608224] ata1: CPB 18: ctl_flags 0x1f, resp_flags 0x0
[ 109.608268] ata1: timeout waiting for ADMA IDLE, stat=0x400
[ 109.608313] ata1: timeout waiting for ADMA LEGACY, stat=0x400
[ 109.608356] ata1.00: exception Emask 0x0 SAct 0x7ffff SErr 0x0 action 0x2 frozen
[ 109.608410] ata1.00: cmd 61/04:00:18:c1:df/00:00:16:00:00/40 tag 0 cdb 0x0 data 2048 out
[ 109.608412] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 109.609937] ata1.00: cmd 61/06:08:0a:c1:df/00:00:16:00:00/40 tag 1 cdb 0x0 data 3072 out
[ 109.609938] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 109.610041] ata1.00: cmd 61/02:10:06:c1:df/00:00:16:00:00/40 tag 2 cdb 0x0 data 1024 out
[ 109.610042] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 109.610145] ata1.00: cmd 61/04:18:fc:c0:df/00:00:16:00:00/40 tag 3 cdb 0x0 data 2048 out
[ 109.610146] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 109.610249] ata1.00: cmd 61/02:20:f8:c0:df/00:00:16:00:00/40 tag 4 cdb 0x0 data 1024 out
[ 109.610250] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 109.610353] ata1.00: cmd 61/02:28:f0:c0:df/00:00:16:00:00/40 tag 5 cdb 0x0 data 1024 out
[ 109.610354] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 109.610456] ata1.00: cmd 61/02:30:e0:c0:df/00:00:16:00:00/40 tag 6 cdb 0x0 data 1024 out
[ 109.610458] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 109.610560] ata1.00: cmd 61/02:38:d8:c0:df/00:00:16:00:00/40 tag 7 cdb 0x0 data 1024 out
[ 109.610562] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 109.610664] ata1.00: cmd 61/06:40:d0:c0:df/00:00:16:00:00/40 tag 8 cdb 0x0 data 3072 out
[ 109.610666] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.610768] ata1.00: cmd 61/04:48:ca:c0:df/00:00:16:00:00/40 tag 9 cdb 0x0 data 2048 out
[ 109.610769] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.610871] ata1.00: cmd 61/04:50:08:c0:df/00:00:16:00:00/40 tag 10 cdb 0x0 data 2048 out
[ 109.610873] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.610975] ata1.00: cmd 61/06:58:bc:bf:df/00:00:16:00:00/40 tag 11 cdb 0x0 data 3072 out
[ 109.610977] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.611079] ata1.00: cmd 61/04:60:c4:bf:df/00:00:16:00:00/40 tag 12 cdb 0x0 data 2048 out
[ 109.611081] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.611183] ata1.00: cmd 61/02:68:d6:bf:df/00:00:16:00:00/40 tag 13 cdb 0x0 data 1024 out
[ 109.611185] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.611287] ata1.00: cmd 61/04:70:dc:bf:df/00:00:16:00:00/40 tag 14 cdb 0x0 data 2048 out
[ 109.611288] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.611391] ata1.00: cmd 61/02:78:e8:bf:df/00:00:16:00:00/40 tag 15 cdb 0x0 data 1024 out
[ 109.611392] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.611497] ata1.00: cmd 61/02:80:f2:bf:df/00:00:16:00:00/40 tag 16 cdb 0x0 data 1024 out
[ 109.611498] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.611601] ata1.00: cmd 61/04:88:fa:bf:df/00:00:16:00:00/40 tag 17 cdb 0x0 data 2048 out
[ 109.611602] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.611704] ata1.00: cmd 61/02:90:02:c1:df/00:00:16:00:00/40 tag 18 cdb 0x0 data 1024 out
[ 109.611706] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 109.923055] ata1: soft resetting port
[ 110.078863] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 110.104389] ata1.00: configured for UDMA/133
[ 110.104437] ata1: EH complete
[ 110.104480] ata1: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x400
[ 110.104543] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 110.104588] sd 0:0:0:0: [sda] Write Protect is off
[ 110.104625] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 110.104636] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 140.063908] ata1: EH in ADMA mode, notifier 0x0 notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x12 next cpb idx 0x0
[ 140.063965] ata1: CPB 0: ctl_flags 0x1f, resp_flags 0x2
[ 140.064003] ata1: CPB 1: ctl_flags 0x1f, resp_flags 0x0
[ 140.064041] ata1: CPB 2: ctl_flags 0x1f, resp_flags 0x0
[ 140.064079] ata1: CPB 3: ctl_flags 0x1f, resp_flags 0x0
[ 140.064117] ata1: CPB 4: ctl_flags 0x1f, resp_flags 0x0
[ 140.064156] ata1: CPB 5: ctl_flags 0x1f, resp_flags 0x0
[ 140.064194] ata1: CPB 6: ctl_flags 0x1f, resp_flags 0x0
[ 140.064232] ata1: CPB 7: ctl_flags 0x1f, resp_flags 0x0
[ 140.064270] ata1: CPB 8: ctl_flags 0x1f, resp_flags 0x0
[ 140.064308] ata1: CPB 9: ctl_flags 0x1f, resp_flags 0x0
[ 140.064346] ata1: CPB 10: ctl_flags 0x1f, resp_flags 0x0
[ 140.064384] ata1: CPB 11: ctl_flags 0x1f, resp_flags 0x0
[ 140.064422] ata1: CPB 12: ctl_flags 0x1f, resp_flags 0x0
[ 140.064460] ata1: CPB 13: ctl_flags 0x1f, resp_flags 0x0
[ 140.064498] ata1: CPB 14: ctl_flags 0x1f, resp_flags 0x0
[ 140.064537] ata1: CPB 15: ctl_flags 0x1f, resp_flags 0x0
[ 140.064575] ata1: CPB 16: ctl_flags 0x1f, resp_flags 0x0
[ 140.064613] ata1: CPB 17: ctl_flags 0x1f, resp_flags 0x0
[ 140.064651] ata1: CPB 18: ctl_flags 0x1f, resp_flags 0x0
[ 140.064695] ata1: timeout waiting for ADMA IDLE, stat=0x400
[ 140.064740] ata1: timeout waiting for ADMA LEGACY, stat=0x400
[ 140.064782] ata1.00: NCQ disabled due to excessive errors
[ 140.064821] ata1.00: exception Emask 0x0 SAct 0x7ffff SErr 0x0 action 0x2 frozen
[ 140.064875] ata1.00: cmd 61/02:00:02:c1:df/00:00:16:00:00/40 tag 0 cdb 0x0 data 1024 out
[ 140.064877] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 140.064979] ata1.00: cmd 61/04:08:fa:bf:df/00:00:16:00:00/40 tag 1 cdb 0x0 data 2048 out
[ 140.064981] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 140.065083] ata1.00: cmd 61/02:10:f2:bf:df/00:00:16:00:00/40 tag 2 cdb 0x0 data 1024 out
[ 140.065085] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 140.065187] ata1.00: cmd 61/02:18:e8:bf:df/00:00:16:00:00/40 tag 3 cdb 0x0 data 1024 out
[ 140.065188] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 140.065290] ata1.00: cmd 61/04:20:dc:bf:df/00:00:16:00:00/40 tag 4 cdb 0x0 data 2048 out
[ 140.065292] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 140.065394] ata1.00: cmd 61/02:28:d6:bf:df/00:00:16:00:00/40 tag 5 cdb 0x0 data 1024 out
[ 140.065396] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 140.065498] ata1.00: cmd 61/04:30:c4:bf:df/00:00:16:00:00/40 tag 6 cdb 0x0 data 2048 out
[ 140.065500] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 140.065602] ata1.00: cmd 61/06:38:bc:bf:df/00:00:16:00:00/40 tag 7 cdb 0x0 data 3072 out
[ 140.065603] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 140.065705] ata1.00: cmd 61/04:40:08:c0:df/00:00:16:00:00/40 tag 8 cdb 0x0 data 2048 out
[ 140.065707] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.065809] ata1.00: cmd 61/04:48:ca:c0:df/00:00:16:00:00/40 tag 9 cdb 0x0 data 2048 out
[ 140.065810] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.065912] ata1.00: cmd 61/06:50:d0:c0:df/00:00:16:00:00/40 tag 10 cdb 0x0 data 3072 out
[ 140.065914] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.066016] ata1.00: cmd 61/02:58:d8:c0:df/00:00:16:00:00/40 tag 11 cdb 0x0 data 1024 out
[ 140.066018] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.066120] ata1.00: cmd 61/02:60:e0:c0:df/00:00:16:00:00/40 tag 12 cdb 0x0 data 1024 out
[ 140.066121] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.066224] ata1.00: cmd 61/02:68:f0:c0:df/00:00:16:00:00/40 tag 13 cdb 0x0 data 1024 out
[ 140.066225] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.066327] ata1.00: cmd 61/02:70:f8:c0:df/00:00:16:00:00/40 tag 14 cdb 0x0 data 1024 out
[ 140.066329] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.066431] ata1.00: cmd 61/04:78:fc:c0:df/00:00:16:00:00/40 tag 15 cdb 0x0 data 2048 out
[ 140.066433] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.066535] ata1.00: cmd 61/02:80:06:c1:df/00:00:16:00:00/40 tag 16 cdb 0x0 data 1024 out
[ 140.066537] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.066639] ata1.00: cmd 61/06:88:0a:c1:df/00:00:16:00:00/40 tag 17 cdb 0x0 data 3072 out
[ 140.066641] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.066743] ata1.00: cmd 61/04:90:18:c1:df/00:00:16:00:00/40 tag 18 cdb 0x0 data 2048 out
[ 140.066744] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.379482] ata1: soft resetting port
[ 140.535289] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 140.560308] ata1.00: configured for UDMA/133
[ 140.560356] ata1: EH complete
[ 140.560400] ata1: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x400
[ 170.520332] ata1: EH in ADMA mode, notifier 0x0 notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x0 next cpb idx 0x0
[ 170.520389] ata1: CPB 0: ctl_flags 0xd, resp_flags 0x0
[ 170.520433] ata1: timeout waiting for ADMA IDLE, stat=0x400
[ 170.520477] ata1: timeout waiting for ADMA LEGACY, stat=0x400
[ 170.520521] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
[ 170.520565] ata1.00: cmd 35/00:04:18:c1:df/00:00:16:00:00/e0 tag 0 cdb 0x0 data 2048 out
[ 170.520567] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
[ 170.831913] ata1: soft resetting port
[ 170.987721] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 171.012723] ata1.00: configured for UDMA/133
[ 171.012762] ata1: EH complete
[ 171.162056] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 171.166591] sd 0:0:0:0: [sda] Write Protect is off
[ 171.166629] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 171.178390] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 171.195572] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 171.204351] sd 0:0:0:0: [sda] Write Protect is off
[ 171.204389] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 171.214556] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: regression problem with Maxtor disk
2007-08-15 21:22 ` Lieven Marchand
@ 2007-08-15 23:31 ` Robert Hancock
0 siblings, 0 replies; 8+ messages in thread
From: Robert Hancock @ 2007-08-15 23:31 UTC (permalink / raw)
To: Lieven Marchand; +Cc: Tejun Heo, jgarzik, linux-ide
Lieven Marchand wrote:
> Tejun Heo <htejun@gmail.com> writes:
>
>> It seems klogd clipped some messages. Can you please turn on printk
>> timestamp, enlarge printk log buffersize and post the result of 'dmesg'
>> after errors?
>
> [ 34.576963] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> [ 34.586151] ata1.00: ATA-7: Maxtor 7H500F0, HA431DN0, max UDMA/133
> [ 34.586191] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
> [ 34.602085] ata1.00: configured for UDMA/133
..
> [ 48.994556] ata1: timeout waiting for ADMA IDLE, stat=0x440
> [ 49.147577] ata1: failed to read log page 10h (errno=-2)
> [ 49.149046] ata1.00: exception Emask 0x1 SAct 0xff SErr 0x0 action 0x0
> [ 49.149086] ata1.00: (CPB resp_flags 0x11: CMD error)
> [ 49.149129] ata1.00: cmd 61/06:00:bc:bf:df/00:00:16:00:00/40 tag 0 cdb 0x0 data 3072 out
> [ 49.149131] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
> [ 49.149234] ata1.00: cmd 61/04:08:c4:bf:df/00:00:16:00:00/40 tag 1 cdb 0x0 data 2048 out
> [ 49.149236] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
> [ 49.149338] ata1.00: cmd 61/02:10:d6:bf:df/00:00:16:00:00/40 tag 2 cdb 0x0 data 1024 out
> [ 49.149340] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
> [ 49.149443] ata1.00: cmd 61/04:18:dc:bf:df/00:00:16:00:00/40 tag 3 cdb 0x0 data 2048 out
> [ 49.149445] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
> [ 49.149547] ata1.00: cmd 61/02:20:e8:bf:df/00:00:16:00:00/40 tag 4 cdb 0x0 data 1024 out
> [ 49.149549] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
> [ 49.149652] ata1.00: cmd 61/02:28:f2:bf:df/00:00:16:00:00/40 tag 5 cdb 0x0 data 1024 out
> [ 49.149653] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
> [ 49.149756] ata1.00: cmd 61/04:30:fa:bf:df/00:00:16:00:00/40 tag 6 cdb 0x0 data 2048 out
> [ 49.149758] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
> [ 49.149860] ata1.00: cmd 61/02:38:04:c0:df/00:00:16:00:00/40 tag 7 cdb 0x0 data 1024 out
> [ 49.149862] res 51/04:00:16:00:00/04:00:16:00:00/40 Emask 0x1 (device error)
> [ 49.175045] ata1.00: configured for UDMA/133
> [ 49.175095] ata1: EH complete
> [ 49.175145] ata1: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x440
> [ 49.175237] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
> [ 49.175285] sd 0:0:0:0: [sda] Write Protect is off
> [ 49.175323] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 49.175334] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
I'm not sure exactly what the controller asserting CMD error on the CPB
means (I don't think either Jeff or NVIDIA ever let out that particular
bit of info), but presumably some kind of FIS error. It seems like the
drive is not responding after this point, everything times out. Likely
model "Maxtor 7H500F0" and firmware "HA431DN0" needs to be added to the
NCQ blacklist. I think this is a similar symptom to some other Maxtor
disks which seem to wedge up when NCQ is used..
> [ 79.155040] ata1: EH in ADMA mode, notifier 0x0 notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x17 next cpb idx 0x0
> [ 79.155098] ata1: CPB 0: ctl_flags 0x1f, resp_flags 0x2
> [ 79.155136] ata1: CPB 1: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155174] ata1: CPB 2: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155212] ata1: CPB 3: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155250] ata1: CPB 4: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155288] ata1: CPB 5: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155326] ata1: CPB 6: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155364] ata1: CPB 7: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155402] ata1: CPB 8: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155440] ata1: CPB 9: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155478] ata1: CPB 10: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155517] ata1: CPB 11: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155555] ata1: CPB 12: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155593] ata1: CPB 13: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155631] ata1: CPB 14: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155669] ata1: CPB 15: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155708] ata1: CPB 16: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155746] ata1: CPB 17: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155784] ata1: CPB 18: ctl_flags 0x1f, resp_flags 0x0
> [ 79.155828] ata1: timeout waiting for ADMA IDLE, stat=0x400
> [ 79.155873] ata1: timeout waiting for ADMA LEGACY, stat=0x400
> [ 79.155917] ata1.00: exception Emask 0x0 SAct 0x7ffff SErr 0x0 action 0x2 frozen
> [ 79.155971] ata1.00: cmd 61/02:00:02:c1:df/00:00:16:00:00/40 tag 0 cdb 0x0 data 1024 out
> [ 79.155973] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 79.156075] ata1.00: cmd 61/04:08:fa:bf:df/00:00:16:00:00/40 tag 1 cdb 0x0 data 2048 out
> [ 79.156077] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 79.156179] ata1.00: cmd 61/02:10:f2:bf:df/00:00:16:00:00/40 tag 2 cdb 0x0 data 1024 out
> [ 79.156180] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 79.156282] ata1.00: cmd 61/02:18:e8:bf:df/00:00:16:00:00/40 tag 3 cdb 0x0 data 1024 out
> [ 79.156284] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 79.156386] ata1.00: cmd 61/04:20:dc:bf:df/00:00:16:00:00/40 tag 4 cdb 0x0 data 2048 out
> [ 79.156388] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 79.156490] ata1.00: cmd 61/02:28:d6:bf:df/00:00:16:00:00/40 tag 5 cdb 0x0 data 1024 out
> [ 79.156492] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 79.156594] ata1.00: cmd 61/04:30:c4:bf:df/00:00:16:00:00/40 tag 6 cdb 0x0 data 2048 out
> [ 79.156596] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 79.156698] ata1.00: cmd 61/06:38:bc:bf:df/00:00:16:00:00/40 tag 7 cdb 0x0 data 3072 out
> [ 79.156699] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 79.156801] ata1.00: cmd 61/04:40:08:c0:df/00:00:16:00:00/40 tag 8 cdb 0x0 data 2048 out
> [ 79.156803] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.156905] ata1.00: cmd 61/04:48:ca:c0:df/00:00:16:00:00/40 tag 9 cdb 0x0 data 2048 out
> [ 79.156907] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.157009] ata1.00: cmd 61/06:50:d0:c0:df/00:00:16:00:00/40 tag 10 cdb 0x0 data 3072 out
> [ 79.157011] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.157113] ata1.00: cmd 61/02:58:d8:c0:df/00:00:16:00:00/40 tag 11 cdb 0x0 data 1024 out
> [ 79.157114] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.157216] ata1.00: cmd 61/02:60:e0:c0:df/00:00:16:00:00/40 tag 12 cdb 0x0 data 1024 out
> [ 79.157218] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.157320] ata1.00: cmd 61/02:68:f0:c0:df/00:00:16:00:00/40 tag 13 cdb 0x0 data 1024 out
> [ 79.157322] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.157424] ata1.00: cmd 61/02:70:f8:c0:df/00:00:16:00:00/40 tag 14 cdb 0x0 data 1024 out
> [ 79.157426] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.157528] ata1.00: cmd 61/04:78:fc:c0:df/00:00:16:00:00/40 tag 15 cdb 0x0 data 2048 out
> [ 79.157529] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.157631] ata1.00: cmd 61/02:80:06:c1:df/00:00:16:00:00/40 tag 16 cdb 0x0 data 1024 out
> [ 79.157633] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.157735] ata1.00: cmd 61/06:88:0a:c1:df/00:00:16:00:00/40 tag 17 cdb 0x0 data 3072 out
> [ 79.157737] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.157839] ata1.00: cmd 61/04:90:18:c1:df/00:00:16:00:00/40 tag 18 cdb 0x0 data 2048 out
> [ 79.157841] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 79.466629] ata1: soft resetting port
> [ 79.622437] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> [ 79.647445] ata1.00: configured for UDMA/133
> [ 79.647494] ata1: EH complete
> [ 79.647538] ata1: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x400
> [ 79.647602] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
> [ 79.647648] sd 0:0:0:0: [sda] Write Protect is off
> [ 79.647686] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 79.647697] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
> [ 109.607481] ata1: EH in ADMA mode, notifier 0x0 notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x12 next cpb idx 0x0
> [ 109.607538] ata1: CPB 0: ctl_flags 0x1f, resp_flags 0x2
> [ 109.607576] ata1: CPB 1: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607614] ata1: CPB 2: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607652] ata1: CPB 3: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607690] ata1: CPB 4: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607728] ata1: CPB 5: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607766] ata1: CPB 6: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607804] ata1: CPB 7: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607842] ata1: CPB 8: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607880] ata1: CPB 9: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607919] ata1: CPB 10: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607957] ata1: CPB 11: ctl_flags 0x1f, resp_flags 0x0
> [ 109.607995] ata1: CPB 12: ctl_flags 0x1f, resp_flags 0x0
> [ 109.608033] ata1: CPB 13: ctl_flags 0x1f, resp_flags 0x0
> [ 109.608071] ata1: CPB 14: ctl_flags 0x1f, resp_flags 0x0
> [ 109.608110] ata1: CPB 15: ctl_flags 0x1f, resp_flags 0x0
> [ 109.608148] ata1: CPB 16: ctl_flags 0x1f, resp_flags 0x0
> [ 109.608186] ata1: CPB 17: ctl_flags 0x1f, resp_flags 0x0
> [ 109.608224] ata1: CPB 18: ctl_flags 0x1f, resp_flags 0x0
> [ 109.608268] ata1: timeout waiting for ADMA IDLE, stat=0x400
> [ 109.608313] ata1: timeout waiting for ADMA LEGACY, stat=0x400
> [ 109.608356] ata1.00: exception Emask 0x0 SAct 0x7ffff SErr 0x0 action 0x2 frozen
> [ 109.608410] ata1.00: cmd 61/04:00:18:c1:df/00:00:16:00:00/40 tag 0 cdb 0x0 data 2048 out
> [ 109.608412] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 109.609937] ata1.00: cmd 61/06:08:0a:c1:df/00:00:16:00:00/40 tag 1 cdb 0x0 data 3072 out
> [ 109.609938] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 109.610041] ata1.00: cmd 61/02:10:06:c1:df/00:00:16:00:00/40 tag 2 cdb 0x0 data 1024 out
> [ 109.610042] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 109.610145] ata1.00: cmd 61/04:18:fc:c0:df/00:00:16:00:00/40 tag 3 cdb 0x0 data 2048 out
> [ 109.610146] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 109.610249] ata1.00: cmd 61/02:20:f8:c0:df/00:00:16:00:00/40 tag 4 cdb 0x0 data 1024 out
> [ 109.610250] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 109.610353] ata1.00: cmd 61/02:28:f0:c0:df/00:00:16:00:00/40 tag 5 cdb 0x0 data 1024 out
> [ 109.610354] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 109.610456] ata1.00: cmd 61/02:30:e0:c0:df/00:00:16:00:00/40 tag 6 cdb 0x0 data 1024 out
> [ 109.610458] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 109.610560] ata1.00: cmd 61/02:38:d8:c0:df/00:00:16:00:00/40 tag 7 cdb 0x0 data 1024 out
> [ 109.610562] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 109.610664] ata1.00: cmd 61/06:40:d0:c0:df/00:00:16:00:00/40 tag 8 cdb 0x0 data 3072 out
> [ 109.610666] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.610768] ata1.00: cmd 61/04:48:ca:c0:df/00:00:16:00:00/40 tag 9 cdb 0x0 data 2048 out
> [ 109.610769] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.610871] ata1.00: cmd 61/04:50:08:c0:df/00:00:16:00:00/40 tag 10 cdb 0x0 data 2048 out
> [ 109.610873] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.610975] ata1.00: cmd 61/06:58:bc:bf:df/00:00:16:00:00/40 tag 11 cdb 0x0 data 3072 out
> [ 109.610977] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.611079] ata1.00: cmd 61/04:60:c4:bf:df/00:00:16:00:00/40 tag 12 cdb 0x0 data 2048 out
> [ 109.611081] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.611183] ata1.00: cmd 61/02:68:d6:bf:df/00:00:16:00:00/40 tag 13 cdb 0x0 data 1024 out
> [ 109.611185] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.611287] ata1.00: cmd 61/04:70:dc:bf:df/00:00:16:00:00/40 tag 14 cdb 0x0 data 2048 out
> [ 109.611288] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.611391] ata1.00: cmd 61/02:78:e8:bf:df/00:00:16:00:00/40 tag 15 cdb 0x0 data 1024 out
> [ 109.611392] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.611497] ata1.00: cmd 61/02:80:f2:bf:df/00:00:16:00:00/40 tag 16 cdb 0x0 data 1024 out
> [ 109.611498] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.611601] ata1.00: cmd 61/04:88:fa:bf:df/00:00:16:00:00/40 tag 17 cdb 0x0 data 2048 out
> [ 109.611602] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.611704] ata1.00: cmd 61/02:90:02:c1:df/00:00:16:00:00/40 tag 18 cdb 0x0 data 1024 out
> [ 109.611706] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 109.923055] ata1: soft resetting port
> [ 110.078863] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> [ 110.104389] ata1.00: configured for UDMA/133
> [ 110.104437] ata1: EH complete
> [ 110.104480] ata1: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x400
> [ 110.104543] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
> [ 110.104588] sd 0:0:0:0: [sda] Write Protect is off
> [ 110.104625] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 110.104636] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
> [ 140.063908] ata1: EH in ADMA mode, notifier 0x0 notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x12 next cpb idx 0x0
> [ 140.063965] ata1: CPB 0: ctl_flags 0x1f, resp_flags 0x2
> [ 140.064003] ata1: CPB 1: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064041] ata1: CPB 2: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064079] ata1: CPB 3: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064117] ata1: CPB 4: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064156] ata1: CPB 5: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064194] ata1: CPB 6: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064232] ata1: CPB 7: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064270] ata1: CPB 8: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064308] ata1: CPB 9: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064346] ata1: CPB 10: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064384] ata1: CPB 11: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064422] ata1: CPB 12: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064460] ata1: CPB 13: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064498] ata1: CPB 14: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064537] ata1: CPB 15: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064575] ata1: CPB 16: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064613] ata1: CPB 17: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064651] ata1: CPB 18: ctl_flags 0x1f, resp_flags 0x0
> [ 140.064695] ata1: timeout waiting for ADMA IDLE, stat=0x400
> [ 140.064740] ata1: timeout waiting for ADMA LEGACY, stat=0x400
> [ 140.064782] ata1.00: NCQ disabled due to excessive errors
> [ 140.064821] ata1.00: exception Emask 0x0 SAct 0x7ffff SErr 0x0 action 0x2 frozen
> [ 140.064875] ata1.00: cmd 61/02:00:02:c1:df/00:00:16:00:00/40 tag 0 cdb 0x0 data 1024 out
> [ 140.064877] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 140.064979] ata1.00: cmd 61/04:08:fa:bf:df/00:00:16:00:00/40 tag 1 cdb 0x0 data 2048 out
> [ 140.064981] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 140.065083] ata1.00: cmd 61/02:10:f2:bf:df/00:00:16:00:00/40 tag 2 cdb 0x0 data 1024 out
> [ 140.065085] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 140.065187] ata1.00: cmd 61/02:18:e8:bf:df/00:00:16:00:00/40 tag 3 cdb 0x0 data 1024 out
> [ 140.065188] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 140.065290] ata1.00: cmd 61/04:20:dc:bf:df/00:00:16:00:00/40 tag 4 cdb 0x0 data 2048 out
> [ 140.065292] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 140.065394] ata1.00: cmd 61/02:28:d6:bf:df/00:00:16:00:00/40 tag 5 cdb 0x0 data 1024 out
> [ 140.065396] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 140.065498] ata1.00: cmd 61/04:30:c4:bf:df/00:00:16:00:00/40 tag 6 cdb 0x0 data 2048 out
> [ 140.065500] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 140.065602] ata1.00: cmd 61/06:38:bc:bf:df/00:00:16:00:00/40 tag 7 cdb 0x0 data 3072 out
> [ 140.065603] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 140.065705] ata1.00: cmd 61/04:40:08:c0:df/00:00:16:00:00/40 tag 8 cdb 0x0 data 2048 out
> [ 140.065707] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.065809] ata1.00: cmd 61/04:48:ca:c0:df/00:00:16:00:00/40 tag 9 cdb 0x0 data 2048 out
> [ 140.065810] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.065912] ata1.00: cmd 61/06:50:d0:c0:df/00:00:16:00:00/40 tag 10 cdb 0x0 data 3072 out
> [ 140.065914] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.066016] ata1.00: cmd 61/02:58:d8:c0:df/00:00:16:00:00/40 tag 11 cdb 0x0 data 1024 out
> [ 140.066018] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.066120] ata1.00: cmd 61/02:60:e0:c0:df/00:00:16:00:00/40 tag 12 cdb 0x0 data 1024 out
> [ 140.066121] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.066224] ata1.00: cmd 61/02:68:f0:c0:df/00:00:16:00:00/40 tag 13 cdb 0x0 data 1024 out
> [ 140.066225] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.066327] ata1.00: cmd 61/02:70:f8:c0:df/00:00:16:00:00/40 tag 14 cdb 0x0 data 1024 out
> [ 140.066329] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.066431] ata1.00: cmd 61/04:78:fc:c0:df/00:00:16:00:00/40 tag 15 cdb 0x0 data 2048 out
> [ 140.066433] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.066535] ata1.00: cmd 61/02:80:06:c1:df/00:00:16:00:00/40 tag 16 cdb 0x0 data 1024 out
> [ 140.066537] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.066639] ata1.00: cmd 61/06:88:0a:c1:df/00:00:16:00:00/40 tag 17 cdb 0x0 data 3072 out
> [ 140.066641] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.066743] ata1.00: cmd 61/04:90:18:c1:df/00:00:16:00:00/40 tag 18 cdb 0x0 data 2048 out
> [ 140.066744] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 140.379482] ata1: soft resetting port
> [ 140.535289] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> [ 140.560308] ata1.00: configured for UDMA/133
> [ 140.560356] ata1: EH complete
> [ 140.560400] ata1: timeout waiting for ADMA LEGACY clear and IDLE, stat=0x400
> [ 170.520332] ata1: EH in ADMA mode, notifier 0x0 notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x0 next cpb idx 0x0
> [ 170.520389] ata1: CPB 0: ctl_flags 0xd, resp_flags 0x0
> [ 170.520433] ata1: timeout waiting for ADMA IDLE, stat=0x400
> [ 170.520477] ata1: timeout waiting for ADMA LEGACY, stat=0x400
> [ 170.520521] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> [ 170.520565] ata1.00: cmd 35/00:04:18:c1:df/00:00:16:00:00/e0 tag 0 cdb 0x0 data 2048 out
> [ 170.520567] res 40/00:00:16:00:00/04:00:16:00:00/40 Emask 0x4 (timeout)
> [ 170.831913] ata1: soft resetting port
> [ 170.987721] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> [ 171.012723] ata1.00: configured for UDMA/133
> [ 171.012762] ata1: EH complete
> [ 171.162056] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
> [ 171.166591] sd 0:0:0:0: [sda] Write Protect is off
> [ 171.166629] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 171.178390] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
> [ 171.195572] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
> [ 171.204351] sd 0:0:0:0: [sda] Write Protect is off
> [ 171.204389] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 171.214556] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
>
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2007-08-15 23:31 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-08-12 14:14 regression problem with Maxtor disk Lieven Marchand
2007-08-14 9:50 ` Tejun Heo
2007-08-14 23:14 ` Robert Hancock
2007-08-15 7:34 ` Lieven Marchand
2007-08-15 7:53 ` Tejun Heo
2007-08-15 21:22 ` Lieven Marchand
2007-08-15 23:31 ` Robert Hancock
-- strict thread matches above, loose matches on Subject: below --
2007-08-12 23:36 babl
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).