* Fwd: Intel 82801G (ICH7) SATA port reset
[not found] <6b9952490708260411g22dede8ew6549acf0436b6e2e@mail.gmail.com>
@ 2007-08-26 11:14 ` Joris
2007-09-08 7:34 ` Tejun Heo
0 siblings, 1 reply; 2+ messages in thread
From: Joris @ 2007-08-26 11:14 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1: Type: text/plain, Size: 1855 bytes --]
Hello List,
I have a rather annoying problem.
On an Intel S3000AHLX
(http://www.intel.com/design/servers/boards/s3000ah/index.htm)
motherboard, I can't seem to utilize all SATA interfaces to the
maximum.
The first sata interface frequently resets every few seconds under
heavy IO, the net result being ridiculous slow transfers (attach:
dmesg_random_collection_of_errors)
Running debian unstable and it's version of 2.6.22. System contains a
xeon 3210 and an adaptec scsi controller from which I currently boot.
There is little logic in the symptoms:
* if there is no or light IO, no resets occur.
* it's always the sda port that resets (changing cables or disks
doesn't make a difference).
* only specific combinations of disk-usage on the sata disks (attach:
disk_combinations_causing_reset), just using sda alone does not cause
resets.
* reading is enough, writing is (subjectively) worse. dd
if=/dev/sd{a,b,c,d} of=/dev/null & guarantees trouble.
* when the port resets, the disk makes a clearly audible clicking noise
I tried numerous things:
* having the board exchanged with intel for the latest revision
(thanks to my hardware supplier), updating to the latest bios and to a
bios version 6 months old.
* booting with older versions of the linux kernel, 2.6.18 and 2.6.21.
* Using all possible combinations of the bios' matrix/lsi fakeraid and
non-raid modes (always ignoring the "raid" and using the disks
directly), and enable/disable the one PATA port in the bios.
* asked seagate for a drive firmware update, to no avail.
The only workable solution so far is to leave the first sata interface
unused (remove the disk), which is obviously not a very nice solution.
Any hints or suggestions would be welcome, I'd be more than happy to
try out new things.
things. I'm a bit at a loss on how to proceed at the moment.
Kind regards,
Joris
[-- Attachment #2: bootmessages --]
[-- Type: application/octet-stream, Size: 124480 bytes --]
Aug 24 04:44:55 tempname syslogd 1.4.1#20: restart.
Aug 24 04:44:55 tempname kernel: klogd 1.4.1#20, log source = /proc/kmsg started.
Aug 24 04:44:55 tempname kernel: Linux version 2.6.22-1-amd64 (Debian 2.6.22-2) (waldi@debian.org) (gcc version 4.1.3 20070718 (prerelease) (Debian 4.1.2-14)) #1 SMP Mon Jul 23 12:43:14 UTC 2007
Aug 24 04:44:55 tempname kernel: Command line: root=LABEL=soloscsi ro
Aug 24 04:44:55 tempname kernel: BIOS-provided physical RAM map:
Aug 24 04:44:55 tempname kernel: BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 000000000009d400 - 0000000000100000 (reserved)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 0000000000100000 - 00000000dfc0e000 (usable)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfc0e000 - 00000000dfc5f000 (reserved)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfc5f000 - 00000000dfce6000 (usable)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfce6000 - 00000000dfedf000 (ACPI NVS)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfedf000 - 00000000dfeed000 (usable)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfeed000 - 00000000dfeff000 (ACPI data)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfeff000 - 00000000dff00000 (usable)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000fffc0000 - 00000000fffd0000 (reserved)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
Aug 24 04:44:55 tempname kernel: end_pfn_map = 1179648
Aug 24 04:44:55 tempname kernel: DMI 2.4 present.
Aug 24 04:44:55 tempname kernel: ACPI: RSDP 000F0350, 0024 (r2 INTEL )
Aug 24 04:44:55 tempname kernel: ACPI: XSDT DFEFE120, 0074 (r1 INTEL S3000AHX 0 INTL 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: FACP DFEFB000, 00F4 (r3 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: DSDT DFEF6000, 4922 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: FACS DFE71000, 0040
Aug 24 04:44:55 tempname kernel: ACPI: APIC DFEF5000, 0084 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: WDDT DFEF4000, 0040 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: MCFG DFEF3000, 003C (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: ASF! DFEF2000, 009F (r32 INTEL S3000AHX 1 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: SSDT DFEF1000, 0175 (r1 INTEL Cpu0Ist 10 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: SSDT DFEF0000, 0175 (r1 INTEL Cpu1Ist 10 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: SSDT DFEEF000, 0175 (r1 INTEL Cpu2Ist 10 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: SSDT DFEEE000, 0175 (r1 INTEL Cpu3Ist 10 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: SSDT DFEED000, 01BC (r1 INTEL CpuPm 10 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: No NUMA configuration found
Aug 24 04:44:55 tempname kernel: Faking a node at 0000000000000000-0000000120000000
Aug 24 04:44:55 tempname kernel: Bootmem setup node 0 0000000000000000-0000000120000000
Aug 24 04:44:55 tempname kernel: Zone PFN ranges:
Aug 24 04:44:55 tempname kernel: DMA 0 -> 4096
Aug 24 04:44:55 tempname kernel: DMA32 4096 -> 1048576
Aug 24 04:44:55 tempname kernel: Normal 1048576 -> 1179648
Aug 24 04:44:55 tempname kernel: early_node_map[6] active PFN ranges
Aug 24 04:44:55 tempname kernel: 0: 0 -> 157
Aug 24 04:44:55 tempname kernel: 0: 256 -> 916494
Aug 24 04:44:55 tempname kernel: 0: 916575 -> 916710
Aug 24 04:44:55 tempname kernel: 0: 917215 -> 917229
Aug 24 04:44:55 tempname kernel: 0: 917247 -> 917248
Aug 24 04:44:55 tempname kernel: 0: 1048576 -> 1179648
Aug 24 04:44:55 tempname kernel: ACPI: PM-Timer IO Port: 0x408
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Aug 24 04:44:55 tempname kernel: Processor #0 (Bootup-CPU)
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Aug 24 04:44:55 tempname kernel: Processor #2
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Aug 24 04:44:55 tempname kernel: Processor #1
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Aug 24 04:44:55 tempname kernel: Processor #3
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
Aug 24 04:44:55 tempname kernel: ACPI: IOAPIC (id[0x05] address[0xfec00000] gsi_base[0])
Aug 24 04:44:55 tempname kernel: IOAPIC[0]: apic_id 5, address 0xfec00000, GSI 0-23
Aug 24 04:44:55 tempname kernel: ACPI: IOAPIC (id[0x06] address[0xfec10000] gsi_base[30])
Aug 24 04:44:55 tempname kernel: IOAPIC[1]: apic_id 6, address 0xfec10000, GSI 30-53
Aug 24 04:44:55 tempname kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Aug 24 04:44:55 tempname kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Aug 24 04:44:55 tempname kernel: Setting APIC routing to flat
Aug 24 04:44:55 tempname kernel: Using ACPI (MADT) for SMP configuration information
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 000000000009e000 - 0000000000100000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000dfc0e000 - 00000000dfc5f000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000dfce6000 - 00000000dfedf000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000dfeed000 - 00000000dfeff000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000dff00000 - 00000000fffc0000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000fffc0000 - 00000000fffd0000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000fffd0000 - 0000000100000000
Aug 24 04:44:55 tempname kernel: Allocating PCI resources starting at e0000000 (gap: dff00000:200c0000)
Aug 24 04:44:55 tempname kernel: SMP: Allowing 4 CPUs, 0 hotplug CPUs
Aug 24 04:44:55 tempname kernel: PERCPU: Allocating 37896 bytes of per cpu data
Aug 24 04:44:55 tempname kernel: Built 1 zonelists. Total pages: 1030465
Aug 24 04:44:55 tempname kernel: Kernel command line: root=LABEL=soloscsi ro
Aug 24 04:44:55 tempname kernel: Initializing CPU#0
Aug 24 04:44:55 tempname kernel: PID hash table entries: 4096 (order: 12, 32768 bytes)
Aug 24 04:44:55 tempname kernel: time.c: Detected 2133.467 MHz processor.
Aug 24 04:44:55 tempname kernel: Console: colour VGA+ 80x25
Aug 24 04:44:55 tempname kernel: Checking aperture...
Aug 24 04:44:55 tempname kernel: PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Aug 24 04:44:55 tempname kernel: Placing software IO TLB between 0x1050000 - 0x5050000
Aug 24 04:44:55 tempname kernel: Memory: 4049736k/4718592k available (2009k kernel code, 140732k reserved, 946k data, 296k init)
Aug 24 04:44:55 tempname kernel: Calibrating delay using timer specific routine.. 4270.08 BogoMIPS (lpj=8540176)
Aug 24 04:44:55 tempname kernel: Security Framework v1.0.0 initialized
Aug 24 04:44:55 tempname kernel: SELinux: Disabled at boot.
Aug 24 04:44:55 tempname kernel: Capability LSM initialized
Aug 24 04:44:55 tempname kernel: Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Aug 24 04:44:55 tempname kernel: Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Aug 24 04:44:55 tempname kernel: Mount-cache hash table entries: 256
Aug 24 04:44:55 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:44:55 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:44:55 tempname kernel: CPU 0/0 -> Node 0
Aug 24 04:44:55 tempname kernel: using mwait in idle threads.
Aug 24 04:44:55 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:44:55 tempname kernel: CPU: Processor Core ID: 0
Aug 24 04:44:55 tempname kernel: CPU0: Thermal monitoring enabled (TM2)
Aug 24 04:44:55 tempname kernel: SMP alternatives: switching to UP code
Aug 24 04:44:55 tempname kernel: ACPI: Core revision 20070126
Aug 24 04:44:55 tempname kernel: Using local APIC timer interrupts.
Aug 24 04:44:55 tempname kernel: result 16667710
Aug 24 04:44:55 tempname kernel: Detected 16.667 MHz APIC timer.
Aug 24 04:44:55 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:44:55 tempname kernel: Booting processor 1/4 APIC 0x2
Aug 24 04:44:55 tempname kernel: Initializing CPU#1
Aug 24 04:44:55 tempname kernel: Calibrating delay using timer specific routine.. 4267.16 BogoMIPS (lpj=8534335)
Aug 24 04:44:55 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:44:55 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:44:55 tempname kernel: CPU 1/2 -> Node 0
Aug 24 04:44:55 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:44:55 tempname kernel: CPU: Processor Core ID: 2
Aug 24 04:44:55 tempname kernel: CPU1: Thermal monitoring enabled (TM2)
Aug 24 04:44:55 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:44:55 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Aug 24 04:44:55 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:44:55 tempname kernel: Booting processor 2/4 APIC 0x1
Aug 24 04:44:55 tempname kernel: Initializing CPU#2
Aug 24 04:44:55 tempname kernel: Calibrating delay using timer specific routine.. 4267.09 BogoMIPS (lpj=8534184)
Aug 24 04:44:55 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:44:55 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:44:55 tempname kernel: CPU 2/1 -> Node 0
Aug 24 04:44:55 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:44:55 tempname kernel: CPU: Processor Core ID: 1
Aug 24 04:44:55 tempname kernel: CPU2: Thermal monitoring enabled (TM2)
Aug 24 04:44:55 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:44:55 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#2]: passed.
Aug 24 04:44:55 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:44:55 tempname kernel: Booting processor 3/4 APIC 0x3
Aug 24 04:44:55 tempname kernel: Initializing CPU#3
Aug 24 04:44:55 tempname kernel: Calibrating delay using timer specific routine.. 4267.14 BogoMIPS (lpj=8534284)
Aug 24 04:44:55 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:44:55 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:44:55 tempname kernel: CPU 3/3 -> Node 0
Aug 24 04:44:55 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:44:55 tempname kernel: CPU: Processor Core ID: 3
Aug 24 04:44:55 tempname kernel: CPU3: Thermal monitoring enabled (TM2)
Aug 24 04:44:55 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:44:55 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Aug 24 04:44:55 tempname kernel: Brought up 4 CPUs
Aug 24 04:44:55 tempname kernel: migration_cost=23,3090
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 16
Aug 24 04:44:55 tempname kernel: ACPI: bus type pci registered
Aug 24 04:44:55 tempname kernel: PCI: Using configuration type 1
Aug 24 04:44:55 tempname kernel: ACPI: Interpreter enabled
Aug 24 04:44:55 tempname kernel: ACPI: (supports S0 S1 S4 S5)
Aug 24 04:44:55 tempname kernel: ACPI: Using IOAPIC for interrupt routing
Aug 24 04:44:55 tempname kernel: ACPI: PCI Root Bridge [PCI0] (0000:00)
Aug 24 04:44:55 tempname kernel: PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
Aug 24 04:44:55 tempname kernel: PCI quirk: region 0500-053f claimed by ICH6 GPIO
Aug 24 04:44:55 tempname kernel: PCI: PXH quirk detected, disabling MSI for SHPC device
Aug 24 04:44:55 tempname kernel: PCI: Transparent bridge - 0000:00:1e.0
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12)
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12)
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:44:55 tempname kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
Aug 24 04:44:55 tempname kernel: pnp: PnP ACPI init
Aug 24 04:44:55 tempname kernel: ACPI: bus type pnp registered
Aug 24 04:44:55 tempname kernel: pnp: PnP ACPI: found 11 devices
Aug 24 04:44:55 tempname kernel: ACPI: ACPI bus type pnp unregistered
Aug 24 04:44:55 tempname kernel: usbcore: registered new interface driver usbfs
Aug 24 04:44:55 tempname kernel: usbcore: registered new interface driver hub
Aug 24 04:44:55 tempname kernel: usbcore: registered new device driver usb
Aug 24 04:44:55 tempname kernel: PCI: Using ACPI for IRQ routing
Aug 24 04:44:55 tempname kernel: PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 8
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 20
Aug 24 04:44:55 tempname kernel: PCI-GART: No AMD northbridge found.
Aug 24 04:44:55 tempname kernel: ACPI: RTC can wake from S4
Aug 24 04:44:55 tempname kernel: pnp: 00:01: ioport range 0x779-0x780 has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:06: ioport range 0x500-0x53f has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:06: ioport range 0x400-0x47f has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:06: ioport range 0x680-0x6ff has been reserved
Aug 24 04:44:55 tempname kernel: PCI: Bridge: 0000:01:00.0
Aug 24 04:44:55 tempname kernel: IO window: 3000-3fff
Aug 24 04:44:55 tempname kernel: MEM window: e8200000-e82fffff
Aug 24 04:44:55 tempname kernel: PREFETCH window: e8400000-e84fffff
Aug 24 04:44:55 tempname kernel: Time: tsc clocksource has been installed.
Aug 24 04:44:55 tempname kernel: PCI: Bridge: 0000:00:1c.0
Aug 24 04:44:55 tempname kernel: IO window: 3000-3fff
Aug 24 04:44:55 tempname kernel: MEM window: e8200000-e82fffff
Aug 24 04:44:55 tempname kernel: PREFETCH window: e8400000-e84fffff
Aug 24 04:44:55 tempname kernel: PCI: Bridge: 0000:00:1c.4
Aug 24 04:44:55 tempname kernel: IO window: disabled.
Aug 24 04:44:55 tempname kernel: MEM window: disabled.
Aug 24 04:44:55 tempname kernel: PREFETCH window: disabled.
Aug 24 04:44:55 tempname kernel: PCI: Bridge: 0000:00:1c.5
Aug 24 04:44:55 tempname kernel: IO window: 2000-2fff
Aug 24 04:44:55 tempname kernel: MEM window: e8100000-e81fffff
Aug 24 04:44:55 tempname kernel: PREFETCH window: disabled.
Aug 24 04:44:55 tempname kernel: PCI: Bridge: 0000:00:1e.0
Aug 24 04:44:55 tempname kernel: IO window: 1000-1fff
Aug 24 04:44:55 tempname kernel: MEM window: e8000000-e80fffff
Aug 24 04:44:55 tempname kernel: PREFETCH window: e0000000-e7ffffff
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 16
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 2
Aug 24 04:44:55 tempname kernel: IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
Aug 24 04:44:55 tempname kernel: TCP established hash table entries: 524288 (order: 11, 12582912 bytes)
Aug 24 04:44:55 tempname kernel: TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Aug 24 04:44:55 tempname kernel: TCP: Hash tables configured (established 524288 bind 65536)
Aug 24 04:44:55 tempname kernel: TCP reno registered
Aug 24 04:44:55 tempname kernel: checking if image is initramfs... it is
Aug 24 04:44:55 tempname kernel: Freeing initrd memory: 5837k freed
Aug 24 04:44:55 tempname kernel: audit: initializing netlink socket (disabled)
Aug 24 04:44:55 tempname kernel: audit(1187923442.852:1): initialized
Aug 24 04:44:55 tempname kernel: VFS: Disk quotas dquot_6.5.1
Aug 24 04:44:55 tempname kernel: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Aug 24 04:44:55 tempname kernel: io scheduler noop registered
Aug 24 04:44:55 tempname kernel: io scheduler anticipatory registered
Aug 24 04:44:55 tempname kernel: io scheduler deadline registered
Aug 24 04:44:55 tempname kernel: io scheduler cfq registered (default)
Aug 24 04:44:55 tempname kernel: 0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
Aug 24 04:44:55 tempname kernel: assign_interrupt_mode Found MSI capability
Aug 24 04:44:55 tempname last message repeated 2 times
Aug 24 04:44:55 tempname kernel: Real Time Clock Driver v1.12ac
Aug 24 04:44:55 tempname kernel: Linux agpgart interface v0.102 (c) Dave Jones
Aug 24 04:44:55 tempname kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Aug 24 04:44:55 tempname kernel: 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:04:00.3[C] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:44:55 tempname kernel: 0000:04:00.3: ttyS1 at I/O 0x2020 (irq = 19) is a 16550A
Aug 24 04:44:55 tempname kernel: RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
Aug 24 04:44:55 tempname kernel: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
Aug 24 04:44:55 tempname kernel: PNP: PS/2 controller doesn't have AUX irq; using default 12
Aug 24 04:44:55 tempname kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Aug 24 04:44:55 tempname kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
Aug 24 04:44:55 tempname kernel: mice: PS/2 mouse device common for all mice
Aug 24 04:44:55 tempname kernel: TCP bic registered
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 1
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 17
Aug 24 04:44:55 tempname kernel: Freeing unused kernel memory: 296k freed
Aug 24 04:44:55 tempname kernel: input: AT Translated Set 2 keyboard as /class/input/input0
Aug 24 04:44:55 tempname kernel: Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Aug 24 04:44:55 tempname kernel: Copyright (c) 1999-2006 Intel Corporation.
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:44:55 tempname kernel: SCSI subsystem initialized
Aug 24 04:44:55 tempname kernel: USB Universal Host Controller Interface driver v3.0
Aug 24 04:44:55 tempname kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Aug 24 04:44:55 tempname kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Aug 24 04:44:55 tempname kernel: FDC 0 is a post-1991 82077
Aug 24 04:44:55 tempname kernel: e1000: 0000:04:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:15:17:1b:d4:45
Aug 24 04:44:55 tempname kernel: e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:05:05.0[A] -> <6>ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.0: irq 23, io base 0x00004080
Aug 24 04:44:55 tempname kernel: usb usb1: configuration #1 chosen from 1 choice
Aug 24 04:44:55 tempname kernel: hub 1-0:1.0: USB hub found
Aug 24 04:44:55 tempname kernel: hub 1-0:1.0: 2 ports detected
Aug 24 04:44:55 tempname kernel: GSI 17 (level, low) -> IRQ 17
Aug 24 04:44:55 tempname kernel: e1000: 0000:05:05.0: e1000_probe: (PCI:33MHz:32-bit) 00:15:17:1b:d4:46
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.1: irq 19, io base 0x00004060
Aug 24 04:44:55 tempname kernel: usb usb2: configuration #1 chosen from 1 choice
Aug 24 04:44:55 tempname kernel: hub 2-0:1.0: USB hub found
Aug 24 04:44:55 tempname kernel: hub 2-0:1.0: 2 ports detected
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
Aug 24 04:44:55 tempname kernel: usb usb3: configuration #1 chosen from 1 choice
Aug 24 04:44:55 tempname kernel: hub 3-0:1.0: USB hub found
Aug 24 04:44:55 tempname kernel: hub 3-0:1.0: 2 ports detected
Aug 24 04:44:55 tempname kernel: e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.3: UHCI Host Controller
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.3: irq 16, io base 0x00004020
Aug 24 04:44:55 tempname kernel: usb usb4: configuration #1 chosen from 1 choice
Aug 24 04:44:55 tempname kernel: hub 4-0:1.0: USB hub found
Aug 24 04:44:55 tempname kernel: hub 4-0:1.0: 2 ports detected
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
Aug 24 04:44:55 tempname kernel: ehci_hcd 0000:00:1d.7: EHCI Host Controller
Aug 24 04:44:55 tempname kernel: ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
Aug 24 04:44:55 tempname kernel: ehci_hcd 0000:00:1d.7: debug port 1
Aug 24 04:44:55 tempname kernel: ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe8300400
Aug 24 04:44:55 tempname kernel: ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Aug 24 04:44:55 tempname kernel: usb usb5: configuration #1 chosen from 1 choice
Aug 24 04:44:55 tempname kernel: hub 5-0:1.0: USB hub found
Aug 24 04:44:55 tempname kernel: hub 5-0:1.0: 8 ports detected
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:44:55 tempname kernel: ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl RAID mode
Aug 24 04:44:55 tempname kernel: ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
Aug 24 04:44:55 tempname kernel: scsi0 : ahci
Aug 24 04:44:55 tempname kernel: scsi1 : ahci
Aug 24 04:44:55 tempname kernel: scsi2 : ahci
Aug 24 04:44:55 tempname kernel: scsi3 : ahci
Aug 24 04:44:55 tempname kernel: ata1: SATA max UDMA/133 cmd 0xffffc20001434100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:44:55 tempname kernel: ata2: SATA max UDMA/133 cmd 0xffffc20001434180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:44:55 tempname kernel: ata3: SATA max UDMA/133 cmd 0xffffc20001434200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:44:55 tempname kernel: ata4: SATA max UDMA/133 cmd 0xffffc20001434280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:44:55 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:44:55 tempname kernel: ata1.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:44:55 tempname kernel: ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:44:55 tempname kernel: ata1.00: configured for UDMA/133
Aug 24 04:44:55 tempname kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:44:55 tempname kernel: ata2.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:44:55 tempname kernel: ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:44:55 tempname kernel: ata2.00: configured for UDMA/133
Aug 24 04:44:55 tempname kernel: ata3: SATA link down (SStatus 0 SControl 300)
Aug 24 04:44:55 tempname kernel: ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:44:55 tempname kernel: ata4.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:44:55 tempname kernel: ata4.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:44:55 tempname kernel: ata4.00: configured for UDMA/133
Aug 24 04:44:55 tempname kernel: scsi 0:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:44:55 tempname kernel: scsi 1:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:44:55 tempname kernel: scsi 3:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 35 (level, low) -> IRQ 35
Aug 24 04:44:55 tempname kernel: ICH7: IDE controller at PCI slot 0000:00:1f.1
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
Aug 24 04:44:55 tempname kernel: ICH7: chipset revision 1
Aug 24 04:44:55 tempname kernel: ICH7: not 100%% native mode: will probe irqs later
Aug 24 04:44:55 tempname kernel: ide0: BM-DMA at 0x40b0-0x40b7, BIOS settings: hda:pio, hdb:pio
Aug 24 04:44:55 tempname kernel: ide1: BM-DMA at 0x40b8-0x40bf, BIOS settings: hdc:pio, hdd:pio
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sda: sda1
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sdb: sdb1
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sdc: sdc1
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: scsi4 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
Aug 24 04:44:55 tempname kernel: <Adaptec 3960D Ultra160 SCSI adapter>
Aug 24 04:44:55 tempname kernel: aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Aug 24 04:44:55 tempname kernel:
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:02:02.1[B] -> GSI 36 (level, low) -> IRQ 36
Aug 24 04:44:55 tempname kernel: scsi 4:0:1:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:44:55 tempname kernel: scsi4:A:1:0: Tagged Queuing enabled. Depth 8
Aug 24 04:44:55 tempname kernel: target4:0:1: Beginning Domain Validation
Aug 24 04:44:55 tempname kernel: target4:0:1: wide asynchronous
Aug 24 04:44:55 tempname kernel: target4:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:44:55 tempname kernel: target4:0:1: Ending Domain Validation
Aug 24 04:44:55 tempname kernel: scsi 4:0:2:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:44:55 tempname kernel: scsi4:A:2:0: Tagged Queuing enabled. Depth 8
Aug 24 04:44:55 tempname kernel: target4:0:2: Beginning Domain Validation
Aug 24 04:44:55 tempname kernel: target4:0:2: wide asynchronous
Aug 24 04:44:55 tempname kernel: target4:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:44:55 tempname kernel: target4:0:2: Ending Domain Validation
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sdd: sdd1
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sde: unknown partition table
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: scsi5 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
Aug 24 04:44:55 tempname kernel: <Adaptec 3960D Ultra160 SCSI adapter>
Aug 24 04:44:55 tempname kernel: aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
Aug 24 04:44:55 tempname kernel:
Aug 24 04:44:55 tempname kernel: scsi 5:0:0:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:44:55 tempname kernel: scsi5:A:0:0: Tagged Queuing enabled. Depth 8
Aug 24 04:44:55 tempname kernel: target5:0:0: Beginning Domain Validation
Aug 24 04:44:55 tempname kernel: target5:0:0: wide asynchronous
Aug 24 04:44:55 tempname kernel: target5:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:44:55 tempname kernel: target5:0:0: Ending Domain Validation
Aug 24 04:44:55 tempname kernel: scsi 5:0:2:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:44:55 tempname kernel: scsi5:A:2:0: Tagged Queuing enabled. Depth 8
Aug 24 04:44:55 tempname kernel: target5:0:2: Beginning Domain Validation
Aug 24 04:44:55 tempname kernel: target5:0:2: wide asynchronous
Aug 24 04:44:55 tempname kernel: target5:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:44:55 tempname kernel: target5:0:2: Ending Domain Validation
Aug 24 04:44:55 tempname kernel: raid5: automatically using best checksumming function: generic_sse
Aug 24 04:44:55 tempname kernel: generic_sse: 7609.000 MB/sec
Aug 24 04:44:55 tempname kernel: raid5: using function: generic_sse (7609.000 MB/sec)
Aug 24 04:44:55 tempname kernel: raid6: int64x1 2001 MB/s
Aug 24 04:44:55 tempname kernel: raid6: int64x2 2696 MB/s
Aug 24 04:44:55 tempname kernel: raid6: int64x4 2366 MB/s
Aug 24 04:44:55 tempname kernel: raid6: int64x8 1531 MB/s
Aug 24 04:44:55 tempname kernel: raid6: sse2x1 3419 MB/s
Aug 24 04:44:55 tempname kernel: raid6: sse2x2 4151 MB/s
Aug 24 04:44:55 tempname kernel: raid6: sse2x4 6450 MB/s
Aug 24 04:44:55 tempname kernel: raid6: using algorithm sse2x4 (6450 MB/s)
Aug 24 04:44:55 tempname kernel: md: raid6 personality registered for level 6
Aug 24 04:44:55 tempname kernel: md: raid5 personality registered for level 5
Aug 24 04:44:55 tempname kernel: md: raid4 personality registered for level 4
Aug 24 04:44:55 tempname kernel: md: md2 stopped.
Aug 24 04:44:55 tempname kernel: md: bind<sdc1>
Aug 24 04:44:55 tempname kernel: md: bind<sdb1>
Aug 24 04:44:55 tempname kernel: raid5: device sdb1 operational as raid disk 0
Aug 24 04:44:55 tempname kernel: raid5: device sdc1 operational as raid disk 2
Aug 24 04:44:55 tempname kernel: raid5: allocated 3212kB for md2
Aug 24 04:44:55 tempname kernel: RAID5 conf printout:
Aug 24 04:44:55 tempname kernel: --- rd:3 wd:2
Aug 24 04:44:55 tempname kernel: disk 0, o:1, dev:sdb1
Aug 24 04:44:55 tempname kernel: disk 2, o:1, dev:sdc1
Aug 24 04:44:55 tempname kernel: kjournald starting. Commit interval 5 seconds
Aug 24 04:44:55 tempname kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 24 04:44:55 tempname kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Aug 24 04:44:55 tempname kernel: shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Aug 24 04:44:55 tempname kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
Aug 24 04:44:55 tempname kernel: iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
Aug 24 04:44:55 tempname kernel: iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
Aug 24 04:44:55 tempname kernel: input: PC Speaker as /class/input/input1
Aug 24 04:44:55 tempname kernel: intel_rng: Firmware space is locked read-only. <4>intel_rng: If you can't or
Aug 24 04:44:55 tempname kernel: don't want to <4>intel_rng: disable this in firmware setup, and <4>intel_rng: if
Aug 24 04:44:55 tempname kernel: you are certain that your <4>intel_rng: system has a functional
Aug 24 04:44:55 tempname kernel: RNG, try<4>intel_rng: using the 'no_fwh_detect' option.
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sdf: unknown partition table
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sdg: unknown partition table
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: EXT3 FS on sdd1, internal journal
Aug 24 04:44:55 tempname kernel: loop: module loaded
Aug 24 04:44:55 tempname kernel: coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:44:55 tempname kernel: coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:44:55 tempname kernel: coretemp coretemp.2: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:44:55 tempname kernel: coretemp coretemp.3: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:44:55 tempname kernel: device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Aug 24 04:44:55 tempname kernel: md: bind<sda1>
Aug 24 04:44:55 tempname kernel: Ebtables v2.0 registered
Aug 24 04:44:55 tempname kernel: Bridge firewalling registered
Aug 24 04:44:56 tempname kernel: NET: Registered protocol family 10
Aug 24 04:44:56 tempname kernel: lo: Disabled Privacy Extensions
Aug 24 04:44:56 tempname hpiod: 1.6.10 accepting connections at 2208...
Aug 24 04:44:57 tempname kernel: input: Power Button (FF) as /class/input/input2
Aug 24 04:44:57 tempname kernel: ACPI: Power Button (FF) [PWRF]
Aug 24 04:44:57 tempname kernel: input: Sleep Button (CM) as /class/input/input3
Aug 24 04:44:57 tempname kernel: ACPI: Sleep Button (CM) [SLPB]
Aug 24 04:44:57 tempname kernel: lp: driver loaded but no devices found
Aug 24 04:44:57 tempname kernel: ppdev: user-space parallel port driver
Aug 24 04:44:59 tempname dhcdbd: Started up.
Aug 24 04:44:59 tempname kernel: mdadm[4321]: segfault at 0000000000000000 rip 000000000041248e rsp 00007fff10299580 error 4
Aug 24 04:48:29 tempname shutdown[4548]: shutting down for system halt
Aug 24 04:48:37 tempname kernel: Ebtables v2.0 unregistered
Aug 24 04:48:37 tempname kernel: Kernel logging (proc) stopped.
Aug 24 04:48:37 tempname kernel: Kernel log daemon terminating.
Aug 24 04:48:38 tempname exiting on signal 15
Aug 24 04:55:11 tempname syslogd 1.4.1#20: restart.
Aug 24 04:55:11 tempname kernel: klogd 1.4.1#20, log source = /proc/kmsg started.
Aug 24 04:55:11 tempname kernel: Linux version 2.6.22-1-amd64 (Debian 2.6.22-2) (waldi@debian.org) (gcc version 4.1.3 20070718 (prerelease) (Debian 4.1.2-14)) #1 SMP Mon Jul 23 12:43:14 UTC 2007
Aug 24 04:55:11 tempname kernel: Command line: root=LABEL=soloscsi ro
Aug 24 04:55:11 tempname kernel: BIOS-provided physical RAM map:
Aug 24 04:55:11 tempname kernel: BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 000000000009d400 - 0000000000100000 (reserved)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 0000000000100000 - 00000000dfc0e000 (usable)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfc0e000 - 00000000dfc5f000 (reserved)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfc5f000 - 00000000dfce6000 (usable)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfce6000 - 00000000dfedf000 (ACPI NVS)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfedf000 - 00000000dfeed000 (usable)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfeed000 - 00000000dfeff000 (ACPI data)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfeff000 - 00000000dff00000 (usable)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000fffc0000 - 00000000fffd0000 (reserved)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
Aug 24 04:55:11 tempname kernel: end_pfn_map = 1179648
Aug 24 04:55:11 tempname kernel: DMI 2.4 present.
Aug 24 04:55:11 tempname kernel: ACPI: RSDP 000F0350, 0024 (r2 INTEL )
Aug 24 04:55:11 tempname kernel: ACPI: XSDT DFEFE120, 0074 (r1 INTEL S3000AHX 0 INTL 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: FACP DFEFB000, 00F4 (r3 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: DSDT DFEF6000, 4922 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: FACS DFE71000, 0040
Aug 24 04:55:11 tempname kernel: ACPI: APIC DFEF5000, 0084 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: WDDT DFEF4000, 0040 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: MCFG DFEF3000, 003C (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: ASF! DFEF2000, 009F (r32 INTEL S3000AHX 1 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: SSDT DFEF1000, 0175 (r1 INTEL Cpu0Ist 10 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: SSDT DFEF0000, 0175 (r1 INTEL Cpu1Ist 10 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: SSDT DFEEF000, 0175 (r1 INTEL Cpu2Ist 10 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: SSDT DFEEE000, 0175 (r1 INTEL Cpu3Ist 10 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: SSDT DFEED000, 01BC (r1 INTEL CpuPm 10 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: No NUMA configuration found
Aug 24 04:55:11 tempname kernel: Faking a node at 0000000000000000-0000000120000000
Aug 24 04:55:11 tempname kernel: Bootmem setup node 0 0000000000000000-0000000120000000
Aug 24 04:55:11 tempname kernel: Zone PFN ranges:
Aug 24 04:55:11 tempname kernel: DMA 0 -> 4096
Aug 24 04:55:11 tempname kernel: DMA32 4096 -> 1048576
Aug 24 04:55:11 tempname kernel: Normal 1048576 -> 1179648
Aug 24 04:55:11 tempname kernel: early_node_map[6] active PFN ranges
Aug 24 04:55:11 tempname kernel: 0: 0 -> 157
Aug 24 04:55:11 tempname kernel: 0: 256 -> 916494
Aug 24 04:55:11 tempname kernel: 0: 916575 -> 916710
Aug 24 04:55:11 tempname kernel: 0: 917215 -> 917229
Aug 24 04:55:11 tempname kernel: 0: 917247 -> 917248
Aug 24 04:55:11 tempname kernel: 0: 1048576 -> 1179648
Aug 24 04:55:11 tempname kernel: ACPI: PM-Timer IO Port: 0x408
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Aug 24 04:55:11 tempname kernel: Processor #0 (Bootup-CPU)
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Aug 24 04:55:11 tempname kernel: Processor #2
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Aug 24 04:55:11 tempname kernel: Processor #1
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Aug 24 04:55:11 tempname kernel: Processor #3
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
Aug 24 04:55:11 tempname kernel: ACPI: IOAPIC (id[0x05] address[0xfec00000] gsi_base[0])
Aug 24 04:55:11 tempname kernel: IOAPIC[0]: apic_id 5, address 0xfec00000, GSI 0-23
Aug 24 04:55:11 tempname kernel: ACPI: IOAPIC (id[0x06] address[0xfec10000] gsi_base[30])
Aug 24 04:55:11 tempname kernel: IOAPIC[1]: apic_id 6, address 0xfec10000, GSI 30-53
Aug 24 04:55:11 tempname kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Aug 24 04:55:11 tempname kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Aug 24 04:55:11 tempname kernel: Setting APIC routing to flat
Aug 24 04:55:11 tempname kernel: Using ACPI (MADT) for SMP configuration information
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 000000000009e000 - 0000000000100000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000dfc0e000 - 00000000dfc5f000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000dfce6000 - 00000000dfedf000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000dfeed000 - 00000000dfeff000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000dff00000 - 00000000fffc0000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000fffc0000 - 00000000fffd0000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000fffd0000 - 0000000100000000
Aug 24 04:55:11 tempname kernel: Allocating PCI resources starting at e0000000 (gap: dff00000:200c0000)
Aug 24 04:55:11 tempname kernel: SMP: Allowing 4 CPUs, 0 hotplug CPUs
Aug 24 04:55:11 tempname kernel: PERCPU: Allocating 37896 bytes of per cpu data
Aug 24 04:55:11 tempname kernel: Built 1 zonelists. Total pages: 1030465
Aug 24 04:55:11 tempname kernel: Kernel command line: root=LABEL=soloscsi ro
Aug 24 04:55:11 tempname kernel: Initializing CPU#0
Aug 24 04:55:11 tempname kernel: PID hash table entries: 4096 (order: 12, 32768 bytes)
Aug 24 04:55:11 tempname kernel: time.c: Detected 2133.450 MHz processor.
Aug 24 04:55:11 tempname kernel: Console: colour VGA+ 80x25
Aug 24 04:55:11 tempname kernel: Checking aperture...
Aug 24 04:55:11 tempname kernel: PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Aug 24 04:55:11 tempname kernel: Placing software IO TLB between 0x1050000 - 0x5050000
Aug 24 04:55:11 tempname kernel: Memory: 4049736k/4718592k available (2009k kernel code, 140732k reserved, 946k data, 296k init)
Aug 24 04:55:11 tempname kernel: Calibrating delay using timer specific routine.. 4270.10 BogoMIPS (lpj=8540211)
Aug 24 04:55:11 tempname kernel: Security Framework v1.0.0 initialized
Aug 24 04:55:11 tempname kernel: SELinux: Disabled at boot.
Aug 24 04:55:11 tempname kernel: Capability LSM initialized
Aug 24 04:55:11 tempname kernel: Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Aug 24 04:55:11 tempname kernel: Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Aug 24 04:55:11 tempname kernel: Mount-cache hash table entries: 256
Aug 24 04:55:11 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:55:11 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:55:11 tempname kernel: CPU 0/0 -> Node 0
Aug 24 04:55:11 tempname kernel: using mwait in idle threads.
Aug 24 04:55:11 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:55:11 tempname kernel: CPU: Processor Core ID: 0
Aug 24 04:55:11 tempname kernel: CPU0: Thermal monitoring enabled (TM2)
Aug 24 04:55:11 tempname kernel: SMP alternatives: switching to UP code
Aug 24 04:55:11 tempname kernel: ACPI: Core revision 20070126
Aug 24 04:55:11 tempname kernel: Using local APIC timer interrupts.
Aug 24 04:55:11 tempname kernel: result 16667575
Aug 24 04:55:11 tempname kernel: Detected 16.667 MHz APIC timer.
Aug 24 04:55:11 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:55:11 tempname kernel: Booting processor 1/4 APIC 0x2
Aug 24 04:55:11 tempname kernel: Initializing CPU#1
Aug 24 04:55:11 tempname kernel: Calibrating delay using timer specific routine.. 4267.17 BogoMIPS (lpj=8534344)
Aug 24 04:55:11 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:55:11 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:55:11 tempname kernel: CPU 1/2 -> Node 0
Aug 24 04:55:11 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:55:11 tempname kernel: CPU: Processor Core ID: 2
Aug 24 04:55:11 tempname kernel: CPU1: Thermal monitoring enabled (TM2)
Aug 24 04:55:11 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:55:11 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Aug 24 04:55:11 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:55:11 tempname kernel: Booting processor 2/4 APIC 0x1
Aug 24 04:55:11 tempname kernel: Initializing CPU#2
Aug 24 04:55:11 tempname kernel: Calibrating delay using timer specific routine.. 4267.18 BogoMIPS (lpj=8534372)
Aug 24 04:55:11 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:55:11 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:55:11 tempname kernel: CPU 2/1 -> Node 0
Aug 24 04:55:11 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:55:11 tempname kernel: CPU: Processor Core ID: 1
Aug 24 04:55:11 tempname kernel: CPU2: Thermal monitoring enabled (TM2)
Aug 24 04:55:11 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:55:11 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#2]: passed.
Aug 24 04:55:11 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:55:11 tempname kernel: Booting processor 3/4 APIC 0x3
Aug 24 04:55:11 tempname kernel: Initializing CPU#3
Aug 24 04:55:11 tempname kernel: Calibrating delay using timer specific routine.. 4267.15 BogoMIPS (lpj=8534305)
Aug 24 04:55:11 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:55:11 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:55:11 tempname kernel: CPU 3/3 -> Node 0
Aug 24 04:55:11 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:55:11 tempname kernel: CPU: Processor Core ID: 3
Aug 24 04:55:11 tempname kernel: CPU3: Thermal monitoring enabled (TM2)
Aug 24 04:55:11 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:55:11 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Aug 24 04:55:11 tempname kernel: Brought up 4 CPUs
Aug 24 04:55:11 tempname kernel: migration_cost=17,3093
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 16
Aug 24 04:55:11 tempname kernel: ACPI: bus type pci registered
Aug 24 04:55:11 tempname kernel: PCI: Using configuration type 1
Aug 24 04:55:11 tempname kernel: ACPI: Interpreter enabled
Aug 24 04:55:11 tempname kernel: ACPI: (supports S0 S1 S4 S5)
Aug 24 04:55:11 tempname kernel: ACPI: Using IOAPIC for interrupt routing
Aug 24 04:55:11 tempname kernel: ACPI: PCI Root Bridge [PCI0] (0000:00)
Aug 24 04:55:11 tempname kernel: PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
Aug 24 04:55:11 tempname kernel: PCI quirk: region 0500-053f claimed by ICH6 GPIO
Aug 24 04:55:11 tempname kernel: PCI: PXH quirk detected, disabling MSI for SHPC device
Aug 24 04:55:11 tempname kernel: PCI: Transparent bridge - 0000:00:1e.0
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12)
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12)
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:55:11 tempname kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
Aug 24 04:55:11 tempname kernel: pnp: PnP ACPI init
Aug 24 04:55:11 tempname kernel: ACPI: bus type pnp registered
Aug 24 04:55:11 tempname kernel: pnp: PnP ACPI: found 11 devices
Aug 24 04:55:11 tempname kernel: ACPI: ACPI bus type pnp unregistered
Aug 24 04:55:11 tempname kernel: usbcore: registered new interface driver usbfs
Aug 24 04:55:11 tempname kernel: usbcore: registered new interface driver hub
Aug 24 04:55:11 tempname kernel: usbcore: registered new device driver usb
Aug 24 04:55:11 tempname kernel: PCI: Using ACPI for IRQ routing
Aug 24 04:55:11 tempname kernel: PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 8
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 20
Aug 24 04:55:11 tempname kernel: PCI-GART: No AMD northbridge found.
Aug 24 04:55:11 tempname kernel: ACPI: RTC can wake from S4
Aug 24 04:55:11 tempname kernel: pnp: 00:01: ioport range 0x779-0x780 has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:06: ioport range 0x500-0x53f has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:06: ioport range 0x400-0x47f has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:06: ioport range 0x680-0x6ff has been reserved
Aug 24 04:55:11 tempname kernel: PCI: Bridge: 0000:01:00.0
Aug 24 04:55:11 tempname kernel: IO window: 3000-3fff
Aug 24 04:55:11 tempname kernel: MEM window: e8200000-e82fffff
Aug 24 04:55:11 tempname kernel: PREFETCH window: e8400000-e84fffff
Aug 24 04:55:11 tempname kernel: Time: tsc clocksource has been installed.
Aug 24 04:55:11 tempname kernel: PCI: Bridge: 0000:00:1c.0
Aug 24 04:55:11 tempname kernel: IO window: 3000-3fff
Aug 24 04:55:11 tempname kernel: MEM window: e8200000-e82fffff
Aug 24 04:55:11 tempname kernel: PREFETCH window: e8400000-e84fffff
Aug 24 04:55:11 tempname kernel: PCI: Bridge: 0000:00:1c.4
Aug 24 04:55:11 tempname kernel: IO window: disabled.
Aug 24 04:55:11 tempname kernel: MEM window: disabled.
Aug 24 04:55:11 tempname kernel: PREFETCH window: disabled.
Aug 24 04:55:11 tempname kernel: PCI: Bridge: 0000:00:1c.5
Aug 24 04:55:11 tempname kernel: IO window: 2000-2fff
Aug 24 04:55:11 tempname kernel: MEM window: e8100000-e81fffff
Aug 24 04:55:11 tempname kernel: PREFETCH window: disabled.
Aug 24 04:55:11 tempname kernel: PCI: Bridge: 0000:00:1e.0
Aug 24 04:55:11 tempname kernel: IO window: 1000-1fff
Aug 24 04:55:11 tempname kernel: MEM window: e8000000-e80fffff
Aug 24 04:55:11 tempname kernel: PREFETCH window: e0000000-e7ffffff
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 16
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 2
Aug 24 04:55:11 tempname kernel: IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
Aug 24 04:55:11 tempname kernel: TCP established hash table entries: 524288 (order: 11, 12582912 bytes)
Aug 24 04:55:11 tempname kernel: TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Aug 24 04:55:11 tempname kernel: TCP: Hash tables configured (established 524288 bind 65536)
Aug 24 04:55:11 tempname kernel: TCP reno registered
Aug 24 04:55:11 tempname kernel: checking if image is initramfs... it is
Aug 24 04:55:11 tempname kernel: Freeing initrd memory: 5837k freed
Aug 24 04:55:11 tempname kernel: audit: initializing netlink socket (disabled)
Aug 24 04:55:11 tempname kernel: audit(1187924057.764:1): initialized
Aug 24 04:55:11 tempname kernel: VFS: Disk quotas dquot_6.5.1
Aug 24 04:55:11 tempname kernel: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Aug 24 04:55:11 tempname kernel: io scheduler noop registered
Aug 24 04:55:11 tempname kernel: io scheduler anticipatory registered
Aug 24 04:55:11 tempname kernel: io scheduler deadline registered
Aug 24 04:55:11 tempname kernel: io scheduler cfq registered (default)
Aug 24 04:55:11 tempname kernel: 0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
Aug 24 04:55:11 tempname kernel: assign_interrupt_mode Found MSI capability
Aug 24 04:55:11 tempname last message repeated 2 times
Aug 24 04:55:11 tempname kernel: Real Time Clock Driver v1.12ac
Aug 24 04:55:11 tempname kernel: Linux agpgart interface v0.102 (c) Dave Jones
Aug 24 04:55:11 tempname kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Aug 24 04:55:11 tempname kernel: 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:04:00.3[C] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:55:11 tempname kernel: 0000:04:00.3: ttyS1 at I/O 0x2020 (irq = 19) is a 16550A
Aug 24 04:55:11 tempname kernel: RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
Aug 24 04:55:11 tempname kernel: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
Aug 24 04:55:11 tempname kernel: PNP: PS/2 controller doesn't have AUX irq; using default 12
Aug 24 04:55:11 tempname kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Aug 24 04:55:11 tempname kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
Aug 24 04:55:11 tempname kernel: mice: PS/2 mouse device common for all mice
Aug 24 04:55:11 tempname kernel: TCP bic registered
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 1
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 17
Aug 24 04:55:11 tempname kernel: Freeing unused kernel memory: 296k freed
Aug 24 04:55:11 tempname kernel: input: AT Translated Set 2 keyboard as /class/input/input0
Aug 24 04:55:11 tempname kernel: USB Universal Host Controller Interface driver v3.0
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.0: irq 23, io base 0x00004080
Aug 24 04:55:11 tempname kernel: usb usb1: configuration #1 chosen from 1 choice
Aug 24 04:55:11 tempname kernel: hub 1-0:1.0: USB hub found
Aug 24 04:55:11 tempname kernel: hub 1-0:1.0: 2 ports detected
Aug 24 04:55:11 tempname kernel: Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Aug 24 04:55:11 tempname kernel: Copyright (c) 1999-2006 Intel Corporation.
Aug 24 04:55:11 tempname kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Aug 24 04:55:11 tempname kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Aug 24 04:55:11 tempname kernel: SCSI subsystem initialized
Aug 24 04:55:11 tempname kernel: FDC 0 is a post-1991 82077
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.1: irq 19, io base 0x00004060
Aug 24 04:55:11 tempname kernel: usb usb2: configuration #1 chosen from 1 choice
Aug 24 04:55:11 tempname kernel: hub 2-0:1.0: USB hub found
Aug 24 04:55:11 tempname kernel: hub 2-0:1.0: 2 ports detected
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
Aug 24 04:55:11 tempname kernel: usb usb3: configuration #1 chosen from 1 choice
Aug 24 04:55:11 tempname kernel: hub 3-0:1.0: USB hub found
Aug 24 04:55:11 tempname kernel: hub 3-0:1.0: 2 ports detected
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.3: UHCI Host Controller
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.3: irq 16, io base 0x00004020
Aug 24 04:55:11 tempname kernel: usb usb4: configuration #1 chosen from 1 choice
Aug 24 04:55:11 tempname kernel: hub 4-0:1.0: USB hub found
Aug 24 04:55:11 tempname kernel: hub 4-0:1.0: 2 ports detected
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:55:11 tempname kernel: ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl RAID mode
Aug 24 04:55:11 tempname kernel: ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
Aug 24 04:55:11 tempname kernel: scsi0 : ahci
Aug 24 04:55:11 tempname kernel: scsi1 : ahci
Aug 24 04:55:11 tempname kernel: scsi2 : ahci
Aug 24 04:55:11 tempname kernel: scsi3 : ahci
Aug 24 04:55:11 tempname kernel: ata1: SATA max UDMA/133 cmd 0xffffc20001432100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:55:11 tempname kernel: ata2: SATA max UDMA/133 cmd 0xffffc20001432180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:55:11 tempname kernel: ata3: SATA max UDMA/133 cmd 0xffffc20001432200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:55:11 tempname kernel: ata4: SATA max UDMA/133 cmd 0xffffc20001432280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:55:11 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:55:11 tempname kernel: ata1.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:55:11 tempname kernel: ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:55:11 tempname kernel: ata1.00: configured for UDMA/133
Aug 24 04:55:11 tempname kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:55:11 tempname kernel: ata2.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:55:11 tempname kernel: ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:55:11 tempname kernel: ata2.00: configured for UDMA/133
Aug 24 04:55:11 tempname kernel: ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:55:11 tempname kernel: ata3.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:55:11 tempname kernel: ata3.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:55:11 tempname kernel: ata3.00: configured for UDMA/133
Aug 24 04:55:11 tempname kernel: ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:55:11 tempname kernel: ata4.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:55:11 tempname kernel: ata4.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:55:11 tempname kernel: ata4.00: configured for UDMA/133
Aug 24 04:55:11 tempname kernel: scsi 0:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:55:11 tempname kernel: scsi 1:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:55:11 tempname kernel: scsi 2:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:55:11 tempname kernel: scsi 3:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
Aug 24 04:55:11 tempname kernel: ehci_hcd 0000:00:1d.7: EHCI Host Controller
Aug 24 04:55:11 tempname kernel: ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
Aug 24 04:55:11 tempname kernel: ehci_hcd 0000:00:1d.7: debug port 1
Aug 24 04:55:11 tempname kernel: ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe8300400
Aug 24 04:55:11 tempname kernel: ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Aug 24 04:55:11 tempname kernel: usb usb5: configuration #1 chosen from 1 choice
Aug 24 04:55:11 tempname kernel: hub 5-0:1.0: USB hub found
Aug 24 04:55:11 tempname kernel: hub 5-0:1.0: 8 ports detected
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sda: sda1
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sdb: sdb1
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sdc:<6>e1000: 0000:04:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:15:17:1b:d4:45
Aug 24 04:55:11 tempname kernel: sdc1
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sdd: sdd1
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:05:05.0[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:55:11 tempname kernel: e1000: 0000:05:05.0: e1000_probe: (PCI:33MHz:32-bit) 00:15:17:1b:d4:46
Aug 24 04:55:11 tempname kernel: e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 35 (level, low) -> IRQ 35
Aug 24 04:55:11 tempname kernel: scsi4 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
Aug 24 04:55:11 tempname kernel: <Adaptec 3960D Ultra160 SCSI adapter>
Aug 24 04:55:11 tempname kernel: aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Aug 24 04:55:11 tempname kernel:
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:02:02.1[B] -> GSI 36 (level, low) -> IRQ 36
Aug 24 04:55:11 tempname kernel: scsi 4:0:1:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:55:11 tempname kernel: scsi4:A:1:0: Tagged Queuing enabled. Depth 8
Aug 24 04:55:11 tempname kernel: target4:0:1: Beginning Domain Validation
Aug 24 04:55:11 tempname kernel: target4:0:1: wide asynchronous
Aug 24 04:55:11 tempname kernel: target4:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:55:11 tempname kernel: target4:0:1: Ending Domain Validation
Aug 24 04:55:11 tempname kernel: scsi 4:0:2:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:55:11 tempname kernel: scsi4:A:2:0: Tagged Queuing enabled. Depth 8
Aug 24 04:55:11 tempname kernel: target4:0:2: Beginning Domain Validation
Aug 24 04:55:11 tempname kernel: target4:0:2: wide asynchronous
Aug 24 04:55:11 tempname kernel: target4:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:55:11 tempname kernel: target4:0:2: Ending Domain Validation
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sde: sde1
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sdf: unknown partition table
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: scsi5 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
Aug 24 04:55:11 tempname kernel: <Adaptec 3960D Ultra160 SCSI adapter>
Aug 24 04:55:11 tempname kernel: aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
Aug 24 04:55:11 tempname kernel:
Aug 24 04:55:11 tempname kernel: ICH7: IDE controller at PCI slot 0000:00:1f.1
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
Aug 24 04:55:11 tempname kernel: ICH7: chipset revision 1
Aug 24 04:55:11 tempname kernel: ICH7: not 100%% native mode: will probe irqs later
Aug 24 04:55:11 tempname kernel: ide0: BM-DMA at 0x40b0-0x40b7, BIOS settings: hda:pio, hdb:pio
Aug 24 04:55:11 tempname kernel: ide1: BM-DMA at 0x40b8-0x40bf, BIOS settings: hdc:pio, hdd:pio
Aug 24 04:55:11 tempname kernel: scsi 5:0:0:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:55:11 tempname kernel: scsi5:A:0:0: Tagged Queuing enabled. Depth 8
Aug 24 04:55:11 tempname kernel: target5:0:0: Beginning Domain Validation
Aug 24 04:55:11 tempname kernel: target5:0:0: wide asynchronous
Aug 24 04:55:11 tempname kernel: target5:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:55:11 tempname kernel: target5:0:0: Ending Domain Validation
Aug 24 04:55:11 tempname kernel: scsi 5:0:2:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:55:11 tempname kernel: scsi5:A:2:0: Tagged Queuing enabled. Depth 8
Aug 24 04:55:11 tempname kernel: target5:0:2: Beginning Domain Validation
Aug 24 04:55:11 tempname kernel: target5:0:2: wide asynchronous
Aug 24 04:55:11 tempname kernel: target5:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:55:11 tempname kernel: target5:0:2: Ending Domain Validation
Aug 24 04:55:11 tempname kernel: raid5: automatically using best checksumming function: generic_sse
Aug 24 04:55:11 tempname kernel: generic_sse: 7611.000 MB/sec
Aug 24 04:55:11 tempname kernel: raid5: using function: generic_sse (7611.000 MB/sec)
Aug 24 04:55:11 tempname kernel: raid6: int64x1 2000 MB/s
Aug 24 04:55:11 tempname kernel: raid6: int64x2 2677 MB/s
Aug 24 04:55:11 tempname kernel: raid6: int64x4 2373 MB/s
Aug 24 04:55:11 tempname kernel: raid6: int64x8 1534 MB/s
Aug 24 04:55:11 tempname kernel: raid6: sse2x1 3419 MB/s
Aug 24 04:55:11 tempname kernel: raid6: sse2x2 4532 MB/s
Aug 24 04:55:11 tempname kernel: raid6: sse2x4 6506 MB/s
Aug 24 04:55:11 tempname kernel: raid6: using algorithm sse2x4 (6506 MB/s)
Aug 24 04:55:11 tempname kernel: md: raid6 personality registered for level 6
Aug 24 04:55:11 tempname kernel: md: raid5 personality registered for level 5
Aug 24 04:55:11 tempname kernel: md: raid4 personality registered for level 4
Aug 24 04:55:11 tempname kernel: md: md2 stopped.
Aug 24 04:55:11 tempname kernel: md: bind<sdc1>
Aug 24 04:55:11 tempname kernel: md: bind<sdd1>
Aug 24 04:55:11 tempname kernel: md: bind<sdb1>
Aug 24 04:55:11 tempname kernel: raid5: device sdb1 operational as raid disk 0
Aug 24 04:55:11 tempname kernel: raid5: device sdd1 operational as raid disk 2
Aug 24 04:55:11 tempname kernel: raid5: device sdc1 operational as raid disk 1
Aug 24 04:55:11 tempname kernel: raid5: allocated 3212kB for md2
Aug 24 04:55:11 tempname kernel: raid5: raid level 5 set md2 active with 3 out of 3 devices, algorithm 2
Aug 24 04:55:11 tempname kernel: RAID5 conf printout:
Aug 24 04:55:11 tempname kernel: --- rd:3 wd:3
Aug 24 04:55:11 tempname kernel: disk 0, o:1, dev:sdb1
Aug 24 04:55:11 tempname kernel: disk 1, o:1, dev:sdc1
Aug 24 04:55:11 tempname kernel: disk 2, o:1, dev:sdd1
Aug 24 04:55:11 tempname kernel: kjournald starting. Commit interval 5 seconds
Aug 24 04:55:11 tempname kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sdg: unknown partition table
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sdh: unknown partition table
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Aug 24 04:55:11 tempname kernel: shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Aug 24 04:55:11 tempname kernel: input: PC Speaker as /class/input/input1
Aug 24 04:55:11 tempname kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
Aug 24 04:55:11 tempname kernel: iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
Aug 24 04:55:11 tempname kernel: iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:55:11 tempname kernel: intel_rng: Firmware space is locked read-only. <4>intel_rng: If you can't or
Aug 24 04:55:11 tempname kernel: don't want to <4>intel_rng: disable this in firmware setup, and <4>intel_rng: if
Aug 24 04:55:11 tempname kernel: you are certain that your <4>intel_rng: system has a functional
Aug 24 04:55:11 tempname kernel: RNG, try<4>intel_rng: using the 'no_fwh_detect' option.
Aug 24 04:55:11 tempname kernel: EXT3 FS on sde1, internal journal
Aug 24 04:55:11 tempname kernel: loop: module loaded
Aug 24 04:55:11 tempname kernel: coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:55:11 tempname kernel: coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:55:11 tempname kernel: coretemp coretemp.2: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:55:11 tempname kernel: coretemp coretemp.3: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:55:11 tempname kernel: device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Aug 24 04:55:11 tempname kernel: md: bind<sda1>
Aug 24 04:55:11 tempname kernel: Ebtables v2.0 registered
Aug 24 04:55:11 tempname kernel: Bridge firewalling registered
Aug 24 04:55:11 tempname kernel: e1000: eth3: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 10
Aug 24 04:55:11 tempname kernel: lo: Disabled Privacy Extensions
Aug 24 04:55:12 tempname hpiod: 1.6.10 accepting connections at 2208...
Aug 24 04:55:13 tempname kernel: input: Power Button (FF) as /class/input/input2
Aug 24 04:55:13 tempname kernel: ACPI: Power Button (FF) [PWRF]
Aug 24 04:55:13 tempname kernel: input: Sleep Button (CM) as /class/input/input3
Aug 24 04:55:13 tempname kernel: ACPI: Sleep Button (CM) [SLPB]
Aug 24 04:55:13 tempname kernel: lp: driver loaded but no devices found
Aug 24 04:55:13 tempname kernel: ppdev: user-space parallel port driver
Aug 24 04:55:14 tempname dhcdbd: Started up.
Aug 24 04:55:15 tempname kernel: mdadm[4375]: segfault at 0000000000000000 rip 000000000041248e rsp 00007fffa2b38e20 error 4
Aug 23 20:57:38 tempname kernel: md: md2 stopped.
Aug 23 20:57:38 tempname kernel: md: unbind<sdb1>
Aug 23 20:57:38 tempname kernel: md: export_rdev(sdb1)
Aug 23 20:57:38 tempname kernel: md: unbind<sdd1>
Aug 23 20:57:38 tempname kernel: md: export_rdev(sdd1)
Aug 23 20:57:38 tempname kernel: md: unbind<sdc1>
Aug 23 20:57:38 tempname kernel: md: export_rdev(sdc1)
Aug 23 20:59:23 tempname kernel: md: md1 stopped.
Aug 23 20:59:23 tempname kernel: md: unbind<sda1>
Aug 23 20:59:23 tempname kernel: md: export_rdev(sda1)
Aug 23 20:59:23 tempname kernel: md: bind<sdc1>
Aug 23 20:59:23 tempname kernel: md: bind<sdd1>
Aug 23 20:59:23 tempname kernel: md: bind<sdb1>
Aug 23 20:59:23 tempname kernel: raid5: device sdb1 operational as raid disk 0
Aug 23 20:59:23 tempname kernel: raid5: device sdd1 operational as raid disk 2
Aug 23 20:59:23 tempname kernel: raid5: device sdc1 operational as raid disk 1
Aug 23 20:59:23 tempname kernel: raid5: allocated 3212kB for md2
Aug 23 20:59:23 tempname kernel: raid5: raid level 5 set md2 active with 3 out of 3 devices, algorithm 2
Aug 23 20:59:23 tempname kernel: RAID5 conf printout:
Aug 23 20:59:23 tempname kernel: --- rd:3 wd:3
Aug 23 20:59:23 tempname kernel: disk 0, o:1, dev:sdb1
Aug 23 20:59:23 tempname kernel: disk 1, o:1, dev:sdc1
Aug 23 20:59:23 tempname kernel: disk 2, o:1, dev:sdd1
Aug 23 20:59:23 tempname kernel: mdadm[4567]: segfault at 0000000000000000 rip 000000000041248e rsp 00007fff39111510 error 4
Aug 23 20:59:23 tempname kernel: md: bind<sda1>
Aug 23 20:59:47 tempname kernel: md: md2 stopped.
Aug 23 20:59:47 tempname kernel: md: unbind<sdb1>
Aug 23 20:59:47 tempname kernel: md: export_rdev(sdb1)
Aug 23 20:59:47 tempname kernel: md: unbind<sdd1>
Aug 23 20:59:47 tempname kernel: md: export_rdev(sdd1)
Aug 23 20:59:47 tempname kernel: md: unbind<sdc1>
Aug 23 20:59:47 tempname kernel: md: export_rdev(sdc1)
Aug 23 21:00:24 tempname kernel: res 40/00:10:30:08:05/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
Aug 23 21:00:24 tempname last message repeated 16 times
Aug 23 21:00:24 tempname kernel: ata1: soft resetting port
Aug 23 21:00:28 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:00:28 tempname kernel: ata1.00: configured for UDMA/133
Aug 23 21:00:28 tempname kernel: ata1: EH complete
Aug 23 21:00:28 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:00:28 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:00:28 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:00:44 tempname kernel: res 40/00:20:60:e7:0a/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
Aug 23 21:00:44 tempname last message repeated 4 times
Aug 23 21:00:45 tempname kernel: ata1: soft resetting port
Aug 23 21:00:48 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:00:49 tempname kernel: ata1.00: configured for UDMA/133
Aug 23 21:00:49 tempname kernel: ata1: EH complete
Aug 23 21:00:49 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:00:49 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:00:49 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:00:50 tempname kernel: res 40/00:08:18:29:0b/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
Aug 23 21:00:50 tempname last message repeated 12 times
Aug 23 21:00:50 tempname kernel: ata1: soft resetting port
Aug 23 21:00:54 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:00:54 tempname kernel: ata1.00: configured for UDMA/133
Aug 23 21:00:54 tempname kernel: ata1: EH complete
Aug 23 21:00:54 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:00:54 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:00:54 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:00:55 tempname kernel: ata1.00: limiting speed to UDMA/100:PIO4
Aug 23 21:00:55 tempname kernel: res 40/00:08:a8:b6:0b/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
Aug 23 21:00:55 tempname last message repeated 3 times
Aug 23 21:00:56 tempname kernel: ata1: soft resetting port
Aug 23 21:00:59 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:00:59 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:00:59 tempname kernel: ata1: EH complete
Aug 23 21:00:59 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:00:59 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:00:59 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:01:01 tempname kernel: res 40/00:08:08:02:0c/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
Aug 23 21:01:01 tempname last message repeated 10 times
Aug 23 21:01:01 tempname kernel: ata1: soft resetting port
Aug 23 21:01:05 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:01:05 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:01:05 tempname kernel: ata1: EH complete
Aug 23 21:01:05 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:01:05 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:01:05 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:02:07 tempname syslogd 1.4.1#20: restart.
Aug 23 21:07:18 tempname kernel: ata1: hard resetting port
Aug 23 21:07:24 tempname kernel: ata1: port is slow to respond, please be patient (Status 0x80)
Aug 23 21:07:28 tempname kernel: ata1: hard resetting port
Aug 23 21:07:29 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:07:29 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:07:29 tempname kernel: ata1: EH complete
Aug 23 21:07:29 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:07:29 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:07:29 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:13:41 tempname kernel: ata1: soft resetting port
Aug 23 21:13:44 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:13:44 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:13:44 tempname kernel: ata1: EH complete
Aug 23 21:13:44 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:13:44 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:13:44 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:19:56 tempname kernel: ata1: soft resetting port
Aug 23 21:19:59 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:19:59 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:19:59 tempname kernel: ata1: EH complete
Aug 23 21:19:59 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:19:59 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:19:59 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:26:11 tempname kernel: ata1: soft resetting port
Aug 23 21:26:15 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:26:15 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:26:15 tempname kernel: ata1: EH complete
Aug 23 21:26:15 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:26:15 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:26:15 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:32:27 tempname kernel: ata1: soft resetting port
Aug 23 21:32:31 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:32:31 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:32:31 tempname kernel: ata1: EH complete
Aug 23 21:32:31 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:32:31 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:32:31 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:38:42 tempname kernel: ata1: soft resetting port
Aug 23 21:38:46 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:38:46 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:38:46 tempname kernel: ata1: EH complete
Aug 23 21:38:46 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:38:46 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:38:46 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:39:49 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:39:49 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 23 21:39:49 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:39:49 tempname kernel: sdb: sdb1
Aug 23 21:40:31 tempname kernel: sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:40:31 tempname kernel: sd 2:0:0:0: [sdc] Write Protect is off
Aug 23 21:40:31 tempname kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:40:31 tempname kernel: sdc: sdc1
Aug 23 21:44:57 tempname kernel: ata1: soft resetting port
Aug 23 21:45:01 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:45:01 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:45:01 tempname kernel: ata1: EH complete
Aug 23 21:45:01 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:45:01 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:45:01 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:47:03 tempname kernel: sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:47:03 tempname kernel: sd 2:0:0:0: [sdc] Write Protect is off
Aug 23 21:47:03 tempname kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:47:04 tempname kernel: sdc: sdc1
Aug 23 21:48:13 tempname kernel: sd 3:0:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:48:13 tempname kernel: sd 3:0:0:0: [sdd] Write Protect is off
Aug 23 21:48:13 tempname kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:48:13 tempname kernel: sdd: sdd1
Aug 23 21:54:40 tempname kernel: ata1: soft resetting port
Aug 23 21:54:44 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:54:44 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:54:44 tempname kernel: ata1: EH complete
Aug 23 21:54:44 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:54:44 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:54:44 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:00:57 tempname kernel: ata1: hard resetting port
Aug 23 22:01:02 tempname kernel: ata1: port is slow to respond, please be patient (Status 0x80)
Aug 23 22:01:07 tempname kernel: ata1: hard resetting port
Aug 23 22:01:07 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:01:08 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:01:08 tempname kernel: ata1: EH complete
Aug 23 22:01:08 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:01:08 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:01:08 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:07:18 tempname kernel: ata1: soft resetting port
Aug 23 22:07:22 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:07:22 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:07:22 tempname kernel: ata1: EH complete
Aug 23 22:07:22 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:07:22 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:07:22 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:08:01 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:08:01 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 23 22:08:01 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:08:01 tempname kernel: sdb: sdb1
Aug 23 22:13:35 tempname kernel: ata1: soft resetting port
Aug 23 22:13:39 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:13:39 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:13:39 tempname kernel: ata1: EH complete
Aug 23 22:13:39 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:13:39 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:13:39 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:15:31 tempname kernel: md: bind<sdb1>
Aug 23 22:15:33 tempname kernel: md: bind<sdc1>
Aug 23 22:15:34 tempname kernel: md: bind<sdd1>
Aug 23 22:15:35 tempname kernel: raid5: device sdd1 operational as raid disk 3
Aug 23 22:15:35 tempname kernel: raid5: device sdc1 operational as raid disk 2
Aug 23 22:15:35 tempname kernel: raid5: device sdb1 operational as raid disk 1
Aug 23 22:15:35 tempname kernel: RAID5 conf printout:
Aug 23 22:15:35 tempname kernel: --- rd:4 wd:3
Aug 23 22:15:35 tempname kernel: disk 1, o:1, dev:sdb1
Aug 23 22:15:35 tempname kernel: disk 2, o:1, dev:sdc1
Aug 23 22:15:35 tempname kernel: disk 3, o:1, dev:sdd1
Aug 23 22:15:35 tempname kernel: md: md2 stopped.
Aug 23 22:15:35 tempname kernel: md: unbind<sdd1>
Aug 23 22:15:35 tempname kernel: md: export_rdev(sdd1)
Aug 23 22:15:35 tempname kernel: md: unbind<sdc1>
Aug 23 22:15:35 tempname kernel: md: export_rdev(sdc1)
Aug 23 22:15:35 tempname kernel: md: unbind<sdb1>
Aug 23 22:15:35 tempname kernel: md: export_rdev(sdb1)
Aug 23 22:16:55 tempname kernel: md: bind<sdb1>
Aug 23 22:16:56 tempname kernel: md: bind<sdc1>
Aug 23 22:16:58 tempname kernel: md: bind<sdd1>
Aug 23 22:16:58 tempname kernel: raid5: device sdd1 operational as raid disk 3
Aug 23 22:16:58 tempname kernel: raid5: device sdc1 operational as raid disk 2
Aug 23 22:16:58 tempname kernel: raid5: device sdb1 operational as raid disk 1
Aug 23 22:16:58 tempname kernel: RAID5 conf printout:
Aug 23 22:16:58 tempname kernel: --- rd:4 wd:3
Aug 23 22:16:58 tempname kernel: disk 1, o:1, dev:sdb1
Aug 23 22:16:58 tempname kernel: disk 2, o:1, dev:sdc1
Aug 23 22:16:58 tempname kernel: disk 3, o:1, dev:sdd1
Aug 23 22:16:58 tempname kernel: md: md3 stopped.
Aug 23 22:16:58 tempname kernel: md: unbind<sdd1>
Aug 23 22:16:58 tempname kernel: md: export_rdev(sdd1)
Aug 23 22:16:58 tempname kernel: md: unbind<sdc1>
Aug 23 22:16:58 tempname kernel: md: export_rdev(sdc1)
Aug 23 22:16:58 tempname kernel: md: unbind<sdb1>
Aug 23 22:16:58 tempname kernel: md: export_rdev(sdb1)
Aug 23 22:19:52 tempname kernel: ata1: soft resetting port
Aug 23 22:19:55 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:19:55 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:19:55 tempname kernel: ata1: EH complete
Aug 23 22:19:55 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:19:55 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:19:55 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:26:06 tempname kernel: ata1: soft resetting port
Aug 23 22:26:10 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:26:10 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:26:10 tempname kernel: ata1: EH complete
Aug 23 22:26:10 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:26:10 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:26:10 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:32:22 tempname kernel: ata1: soft resetting port
Aug 23 22:32:25 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:32:25 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:32:25 tempname kernel: ata1: EH complete
Aug 23 22:32:25 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:32:25 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:32:25 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:38:36 tempname kernel: ata1: soft resetting port
Aug 23 22:38:40 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:38:40 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:38:40 tempname kernel: ata1: EH complete
Aug 23 22:38:40 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:38:40 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:38:40 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:44:53 tempname kernel: ata1: soft resetting port
Aug 23 22:44:56 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:44:56 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:44:56 tempname kernel: ata1: EH complete
Aug 23 22:44:56 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:44:56 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:44:56 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:51:07 tempname kernel: ata1: soft resetting port
Aug 23 22:51:11 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:51:11 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:51:11 tempname kernel: ata1: EH complete
Aug 23 22:51:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:51:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:51:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:55:10 tempname kernel: Kernel logging (proc) stopped.
Aug 23 22:55:10 tempname kernel: Kernel log daemon terminating.
Aug 23 22:55:11 tempname kernel: klogd 1.5.0#1, log source = /proc/kmsg started.
Aug 23 22:55:12 tempname exiting on signal 15
Aug 23 22:55:12 tempname syslogd 1.5.0#1: restart.
Aug 23 23:00:52 tempname kernel: ata1: soft resetting port
Aug 23 23:00:56 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:00:56 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:00:56 tempname kernel: ata1: EH complete
Aug 23 23:00:56 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:00:56 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:00:56 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:07:08 tempname kernel: ata1: soft resetting port
Aug 23 23:07:11 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:07:11 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:07:11 tempname kernel: ata1: EH complete
Aug 23 23:07:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:07:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:07:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:13:22 tempname kernel: ata1: soft resetting port
Aug 23 23:13:26 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:13:26 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:13:26 tempname kernel: ata1: EH complete
Aug 23 23:13:26 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:13:26 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:13:26 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:19:38 tempname kernel: ata1: soft resetting port
Aug 23 23:19:41 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:19:42 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:19:42 tempname kernel: ata1: EH complete
Aug 23 23:19:42 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:19:42 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:19:42 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:25:53 tempname kernel: ata1: soft resetting port
Aug 23 23:25:57 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:25:57 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:25:57 tempname kernel: ata1: EH complete
Aug 23 23:25:57 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:25:57 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:25:57 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:32:08 tempname kernel: ata1: soft resetting port
Aug 23 23:32:12 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:32:12 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:32:12 tempname kernel: ata1: EH complete
Aug 23 23:32:12 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:32:12 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:32:12 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:38:24 tempname kernel: ata1: soft resetting port
Aug 23 23:38:27 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:38:28 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:38:28 tempname kernel: ata1: EH complete
Aug 23 23:38:28 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:38:28 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:38:28 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:44:38 tempname kernel: ata1: hard resetting port
Aug 23 23:44:44 tempname kernel: ata1: port is slow to respond, please be patient (Status 0x80)
Aug 23 23:44:48 tempname kernel: ata1: hard resetting port
Aug 23 23:44:49 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:44:49 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:44:49 tempname kernel: ata1: EH complete
Aug 23 23:44:49 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:44:49 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:44:49 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:51:01 tempname kernel: ata1: soft resetting port
Aug 23 23:51:05 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:51:05 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:51:05 tempname kernel: ata1: EH complete
Aug 23 23:51:05 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:51:05 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:51:05 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:57:16 tempname kernel: ata1: soft resetting port
Aug 23 23:57:20 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:57:20 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:57:20 tempname kernel: ata1: EH complete
Aug 23 23:57:20 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:57:20 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:57:20 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:03:31 tempname kernel: ata1: soft resetting port
Aug 24 00:03:34 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:03:34 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:03:34 tempname kernel: ata1: EH complete
Aug 24 00:03:34 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:03:34 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:03:34 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:09:46 tempname kernel: ata1: soft resetting port
Aug 24 00:09:50 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:09:50 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:09:50 tempname kernel: ata1: EH complete
Aug 24 00:09:50 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:09:50 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:09:50 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:16:03 tempname kernel: ata1: soft resetting port
Aug 24 00:16:06 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:16:06 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:16:06 tempname kernel: ata1: EH complete
Aug 24 00:16:06 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:16:06 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:16:06 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:22:18 tempname kernel: ata1: soft resetting port
Aug 24 00:22:22 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:22:22 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:22:22 tempname kernel: ata1: EH complete
Aug 24 00:22:22 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:22:22 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:22:22 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:28:34 tempname kernel: ata1: soft resetting port
Aug 24 00:28:37 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:28:37 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:28:37 tempname kernel: ata1: EH complete
Aug 24 00:28:37 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:28:37 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:28:37 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:34:49 tempname kernel: ata1: soft resetting port
Aug 24 00:34:53 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:34:53 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:34:53 tempname kernel: ata1: EH complete
Aug 24 00:34:53 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:34:53 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:34:53 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:41:04 tempname kernel: ata1: soft resetting port
Aug 24 00:41:07 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:41:07 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:41:07 tempname kernel: ata1: EH complete
Aug 24 00:41:07 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:41:07 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:41:07 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:47:19 tempname kernel: ata1: soft resetting port
Aug 24 00:47:22 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:47:22 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:47:22 tempname kernel: ata1: EH complete
Aug 24 00:47:22 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:47:22 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:47:22 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:53:34 tempname kernel: ata1: soft resetting port
Aug 24 00:53:38 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:53:38 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:53:38 tempname kernel: ata1: EH complete
Aug 24 00:53:38 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:53:38 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:53:38 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:59:50 tempname kernel: ata1: soft resetting port
Aug 24 00:59:54 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:59:54 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:59:54 tempname kernel: ata1: EH complete
Aug 24 00:59:54 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:59:54 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:59:54 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:06:06 tempname kernel: ata1: soft resetting port
Aug 24 01:06:09 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:06:09 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:06:09 tempname kernel: ata1: EH complete
Aug 24 01:06:09 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:06:09 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:06:09 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:12:21 tempname kernel: ata1: soft resetting port
Aug 24 01:12:25 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:12:25 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:12:25 tempname kernel: ata1: EH complete
Aug 24 01:12:25 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:12:25 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:12:25 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:18:36 tempname kernel: ata1: soft resetting port
Aug 24 01:18:40 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:18:40 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:18:40 tempname kernel: ata1: EH complete
Aug 24 01:18:40 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:18:40 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:18:40 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:24:52 tempname kernel: ata1: soft resetting port
Aug 24 01:24:55 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:24:55 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:24:55 tempname kernel: ata1: EH complete
Aug 24 01:24:55 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:24:55 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:24:55 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:31:07 tempname kernel: ata1: soft resetting port
Aug 24 01:31:11 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:31:11 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:31:11 tempname kernel: ata1: EH complete
Aug 24 01:31:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:31:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:31:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:37:23 tempname kernel: ata1: soft resetting port
Aug 24 01:37:26 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:37:26 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:37:26 tempname kernel: ata1: EH complete
Aug 24 01:37:26 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:37:26 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:37:26 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:43:39 tempname kernel: ata1: soft resetting port
Aug 24 01:43:43 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:43:43 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:43:43 tempname kernel: ata1: EH complete
Aug 24 01:43:43 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:43:43 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:43:43 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:49:58 tempname kernel: ata1: soft resetting port
Aug 24 01:50:01 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:50:01 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:50:01 tempname kernel: ata1: EH complete
Aug 24 01:50:01 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:50:01 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:50:01 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:56:17 tempname kernel: ata1: soft resetting port
Aug 24 01:56:20 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:56:20 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:56:20 tempname kernel: ata1: EH complete
Aug 24 01:56:20 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:56:20 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:56:20 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:02:32 tempname kernel: ata1: soft resetting port
Aug 24 02:02:36 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:02:36 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:02:36 tempname kernel: ata1: EH complete
Aug 24 02:02:36 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:02:36 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:02:36 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:08:55 tempname kernel: ata1: hard resetting port
Aug 24 02:09:01 tempname kernel: ata1: port is slow to respond, please be patient (Status 0x80)
Aug 24 02:09:05 tempname kernel: ata1: hard resetting port
Aug 24 02:09:06 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:09:06 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:09:06 tempname kernel: ata1: EH complete
Aug 24 02:09:06 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:09:06 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:09:06 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:15:19 tempname kernel: ata1: soft resetting port
Aug 24 02:15:23 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:15:23 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:15:23 tempname kernel: ata1: EH complete
Aug 24 02:15:23 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:15:23 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:15:23 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:21:35 tempname kernel: ata1: soft resetting port
Aug 24 02:21:38 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:21:38 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:21:38 tempname kernel: ata1: EH complete
Aug 24 02:21:38 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:21:38 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:21:38 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:27:50 tempname kernel: ata1: soft resetting port
Aug 24 02:27:54 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:27:54 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:27:54 tempname kernel: ata1: EH complete
Aug 24 02:27:54 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:27:54 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:27:54 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:34:08 tempname kernel: ata1: soft resetting port
Aug 24 02:34:11 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:34:11 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:34:11 tempname kernel: ata1: EH complete
Aug 24 02:34:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:34:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:34:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:40:24 tempname kernel: ata1: soft resetting port
Aug 24 02:40:27 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:40:27 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:40:27 tempname kernel: ata1: EH complete
Aug 24 02:40:27 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:40:27 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:40:27 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:46:47 tempname kernel: ata1: soft resetting port
Aug 24 02:46:51 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:46:51 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:46:51 tempname kernel: ata1: EH complete
Aug 24 02:46:51 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:46:51 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:46:51 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:53:11 tempname kernel: ata1: soft resetting port
Aug 24 02:53:14 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:53:15 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:53:15 tempname kernel: ata1: EH complete
Aug 24 02:53:15 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:53:15 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:53:15 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:59:30 tempname kernel: ata1: soft resetting port
Aug 24 02:59:34 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:59:34 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:59:34 tempname kernel: ata1: EH complete
Aug 24 02:59:34 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:59:34 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:59:34 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:06:22 tempname kernel: ata1: soft resetting port
Aug 24 03:06:26 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:06:26 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:06:26 tempname kernel: ata1: EH complete
Aug 24 03:06:26 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:06:26 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:06:26 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:12:44 tempname kernel: ata1: soft resetting port
Aug 24 03:12:47 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:12:47 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:12:47 tempname kernel: ata1: EH complete
Aug 24 03:12:47 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:12:47 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:12:47 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:33:26 tempname kernel: ata1: soft resetting port
Aug 24 03:33:29 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:33:29 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:33:29 tempname kernel: ata1: EH complete
Aug 24 03:33:29 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:33:29 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:33:29 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:39:44 tempname kernel: ata1: soft resetting port
Aug 24 03:39:47 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:39:47 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:39:47 tempname kernel: ata1: EH complete
Aug 24 03:39:47 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:39:47 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:39:47 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:46:00 tempname kernel: ata1: soft resetting port
Aug 24 03:46:04 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:46:04 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:46:04 tempname kernel: ata1: EH complete
Aug 24 03:46:04 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:46:04 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:46:04 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:52:23 tempname kernel: ata1: soft resetting port
Aug 24 03:52:26 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:52:26 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:52:26 tempname kernel: ata1: EH complete
Aug 24 03:52:26 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:52:26 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:52:26 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:05:55 tempname kernel: ata1: soft resetting port
Aug 24 04:05:59 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:05:59 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 04:05:59 tempname kernel: ata1: EH complete
Aug 24 04:05:59 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:05:59 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:05:59 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:26:32 tempname kernel: ata1: hard resetting port
Aug 24 04:26:38 tempname kernel: ata1: port is slow to respond, please be patient (Status 0x80)
Aug 24 04:26:42 tempname kernel: ata1: hard resetting port
Aug 24 04:26:43 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:26:43 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 04:26:43 tempname kernel: ata1: EH complete
Aug 24 04:26:43 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:26:43 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:26:43 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:16 tempname -- MARK --
[-- Attachment #3: disk_combinations_causing_reset --]
[-- Type: application/octet-stream, Size: 315 bytes --]
READ: dd if=/dev/sdx of=/dev/null
/dev/sda: reset sda
/dev/sdb: ok
/dev/sdc: ok
/dev/sdd: ok
sdb+sdc: reset sda
sdc+sdd: ok
sdb+sdd: ok
sda+sdb: reset sda (but a lot less frequent)
sda+sdc: reset sda
sda+sdd: reset sda
sda+sdb+sdc: reset sda
sda+sdb+sdd: reset sda
sda+sdc+sdd: reset sda
sdb+sdc+sdd: reset sda
[-- Attachment #4: dmesg_random_collection_of_errors --]
[-- Type: application/octet-stream, Size: 62233 bytes --]
>ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:7d:c7/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:7d:c7/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:7e:c7/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:7e:c7/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:7e:c7/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:7e:c7/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:7d:c7/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:7d:c7/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:7d:c7/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:7d:c7/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:7e:c7/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:7e:c7/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 c7 7e e8
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 29851112
printk: 21 messages suppressed.
Buffer I/O error on device sda, logical block 3731389
Buffer I/O error on device sda, logical block 3731390
Buffer I/O error on device sda, logical block 3731391
Buffer I/O error on device sda, logical block 3731392
Buffer I/O error on device sda, logical block 3731393
Buffer I/O error on device sda, logical block 3731394
Buffer I/O error on device sda, logical block 3731395
Buffer I/O error on device sda, logical block 3731396
Buffer I/O error on device sda, logical block 3731397
Buffer I/O error on device sda, logical block 3731398
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 c7 7e e8
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 29851104
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 c7 7e e8
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 29851360
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x3 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:7e:c7/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:08:e0:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:7d:c7/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:08:e0:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 c7 7d e0
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 29851368
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:7d:c7/00:00:01:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:00:e0:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:a0:39/00:00:03:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:9f:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:a0:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:9f:39/00:00:03:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:9f:39/00:00:03:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:a0:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:9f:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:18:e0:a0:39/00:00:03:00:00/40 tag 3 cdb 0x0 data 4096 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:a0:39/00:00:03:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:9f:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:a0:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:9f:39/00:00:03:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:9f:39/00:00:03:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:a0:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:9f:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:18:e0:a0:39/00:00:03:00:00/40 tag 3 cdb 0x0 data 4096 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xe SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/08:08:e0:9f:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:a0:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:9f:39/00:00:03:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x6 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:08:e8:a0:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:10:e0:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:9f:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:10:e0:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
03 39 9f e0
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 54108392
printk: 54 messages suppressed.
Buffer I/O error on device sda, logical block 6763549
Buffer I/O error on device sda, logical block 6763550
Buffer I/O error on device sda, logical block 6763551
Buffer I/O error on device sda, logical block 6763552
Buffer I/O error on device sda, logical block 6763553
Buffer I/O error on device sda, logical block 6763554
Buffer I/O error on device sda, logical block 6763555
Buffer I/O error on device sda, logical block 6763556
Buffer I/O error on device sda, logical block 6763557
Buffer I/O error on device sda, logical block 6763558
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
03 39 9f e0
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 54108128
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x50 SAct 0x0 SErr 0x10800 action 0x6 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: hard resetting port
ata1: port is slow to respond, please be patient (Status 0x80)
ata1: COMRESET failed (errno=-16)
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:3e:da/00:00:02:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:3d:da/00:00:02:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:3d:da/00:00:02:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:3e:da/00:00:02:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xe SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:08:e8:3d:da/00:00:02:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:18:e0:3e:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:3d:da/00:00:02:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e0:3e:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:18:e0:3e:da/00:00:02:00:00/40 tag 3 cdb 0x0 data 4096 in
res 40/00:18:e0:3e:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x6 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/08:08:e0:3d:da/00:00:02:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:3d:da/00:00:02:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x3 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:3d:da/00:00:02:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:08:e0:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:3d:da/00:00:02:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:08:e0:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x2 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:08:e8:3d:da/00:00:02:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:08:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:3d:da/00:00:02:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:00:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
02 da 3d e8
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 47857128
printk: 22 messages suppressed.
Buffer I/O error on device sda, logical block 5982141
Buffer I/O error on device sda, logical block 5982142
Buffer I/O error on device sda, logical block 5982143
Buffer I/O error on device sda, logical block 5982144
Buffer I/O error on device sda, logical block 5982145
Buffer I/O error on device sda, logical block 5982146
Buffer I/O error on device sda, logical block 5982147
Buffer I/O error on device sda, logical block 5982148
Buffer I/O error on device sda, logical block 5982149
Buffer I/O error on device sda, logical block 5982150
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xa SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:08:e0:b7:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:b7:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:b7:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:b8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:b7:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:b8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:b8:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:b8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:b8:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:b8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:b8:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:b8:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:b7:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:b7:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x3 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:b9:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:08:e8:b9:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:b9:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:08:e8:b9:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xc SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:10:e0:c2:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:c2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:c2:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:c2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xc SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:10:e0:c5:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:c5:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:c5:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:c5:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:c7:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:08:e8:c7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:c7:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:08:e8:c7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:c6:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:08:e8:c7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:c6:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:08:e8:c7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xd SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/00:00:e0:c8:19/01:00:01:00:00/40 tag 0 cdb 0x0 data 131072 in
res 40/00:00:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:c7:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:00:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:18:e0:c7:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 4096 in
res 40/00:00:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x7 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:c9:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:c9:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:10:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/00:10:e0:c8:19/01:00:01:00:00/40 tag 2 cdb 0x0 data 131072 in
res 40/00:10:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x7 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/00:00:e0:c8:19/01:00:01:00:00/40 tag 0 cdb 0x0 data 131072 in
res 40/00:10:e0:c9:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:c9:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:10:e0:c9:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:c9:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:10:e0:c9:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:cc:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:00:e8:cc:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x2 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/00:08:e0:cd:19/01:00:01:00:00/40 tag 1 cdb 0x0 data 131072 in
res 40/00:08:e0:cd:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xa SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:08:e0:d2:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:08:e0:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:d2:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:08:e0:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:d2:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:d2:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:d3:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:d3:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:d3:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:d3:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:d2:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:d2:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:d4:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:d4:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:d3:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:d3:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x5 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:17:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:17:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:17:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:18:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:17:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:18:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:18:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:18:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:18:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:18:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:18:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:18:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:17:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:17:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x3 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:19:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:08:e8:19:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:19:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:08:e8:19:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xd SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:1b:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:18:e8:1a:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:1a:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:1a:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:1a:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:1a:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xd SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/00:00:e0:1c:64/01:00:04:00:00/40 tag 0 cdb 0x0 data 131072 in
res 40/00:00:e0:1c:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:1b:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:00:e0:1c:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:1b:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:00:e0:1c:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x50 SAct 0xf SErr 0x10800 action 0x6 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:21:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:08:e8:21:64/00:00:04:00:00/40 Emask 0x50 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:21:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:08:e8:21:64/00:00:04:00:00/40 Emask 0x50 (ATA bus error)
ata1.00: cmd 60/08:10:e0:22:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:08:e8:21:64/00:00:04:00:00/40 Emask 0x50 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:22:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:08:e8:21:64/00:00:04:00:00/40 Emask 0x50 (ATA bus error)
ata1: hard resetting port
ata1: port is slow to respond, please be patient (Status 0x80)
ata1: COMRESET failed (errno=-16)
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:2d:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e8:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:2e:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:10:e8:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:2d:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:2e:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:10:e8:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xe SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:08:e8:2d:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:18:e0:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:2e:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e0:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:18:e0:2d:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 4096 in
res 40/00:18:e0:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:31:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:00:e8:31:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:4d:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:00:e0:4d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:4e:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:00:e0:4d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:4e:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:00:e0:4d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:4d:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:00:e0:4d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x5 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:77:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e8:77:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:77:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:77:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xc SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:10:e0:7a:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:7a:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:7a:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:7a:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xc SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:10:e0:7b:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:7b:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:7b:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:7b:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x6 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:08:e0:21:cd/00:00:04:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:10:e8:21:cd/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:21:cd/00:00:04:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:21:cd/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x5 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:26:b7/00:00:08:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e8:26:b7/00:00:08:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:26:b7/00:00:08:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:26:b7/00:00:08:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[-- Attachment #5: lsmod --]
[-- Type: application/octet-stream, Size: 2402 bytes --]
Module Size Used by
ppdev 13704 0
parport_pc 42664 0
lp 17352 0
parport 44428 3 ppdev,parport_pc,lp
button 13472 0
ac 10376 0
battery 15496 0
acpi_cpufreq 13704 0
cpufreq_ondemand 13328 4
cpufreq_stats 10400 0
freq_table 9600 3 acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
cpufreq_conservative 12424 0
cpufreq_powersave 6272 0
cpufreq_userspace 9472 0
ipv6 296840 22
ebtable_broute 6656 0
bridge 62760 1 ebtable_broute
ebtable_nat 7040 0
ebtable_filter 6912 0
ebtables 23936 3 ebtable_broute,ebtable_nat,ebtable_filter
dm_snapshot 21320 0
dm_mirror 26240 0
dm_mod 63984 2 dm_snapshot,dm_mirror
coretemp 12544 0
eeprom 12432 0
lm85 39332 0
hwmon_vid 7296 1 lm85
kvm_intel 25232 0
kvm 68688 1 kvm_intel
loop 23044 0
psmouse 45468 0
i2c_i801 13468 0
serio_raw 11780 0
i2c_core 31488 3 eeprom,lm85,i2c_i801
iTCO_wdt 15824 1
pcspkr 7680 0
shpchp 38428 0
pci_hotplug 37252 1 shpchp
evdev 15232 0
ext3 137232 1
jbd 68080 1 ext3
mbcache 13832 1 ext3
raid456 126240 0
md_mod 83996 1 raid456
xor 10256 1 raid456
ata_generic 13188 0
piix 14980 0 [permanent]
sd_mod 33280 4
ahci 28676 2
libata 132016 2 ata_generic,ahci
aic7xxx 162908 1
scsi_transport_spi 31744 1 aic7xxx
ehci_hcd 37900 0
scsi_mod 164536 4 sd_mod,libata,aic7xxx,scsi_transport_spi
generic 10372 0 [permanent]
ide_core 147728 2 piix,generic
floppy 67560 0
e1000 127552 0
uhci_hcd 29856 0
thermal 19600 0
processor 39784 2 acpi_cpufreq,thermal
fan 9992 0
[-- Attachment #6: lspci --]
[-- Type: application/octet-stream, Size: 1912 bytes --]
00:00.0 Host bridge: Intel Corporation E7230/3000/3010 Memory Controller Hub
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01)
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 RAID bus controller: Intel Corporation 82801GR/GH (ICH7 Family) Serial ATA Storage Controller RAID (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 PCI bridge: Intel Corporation 6702PXH PCI Express-to-PCI Bridge A (rev 09)
02:02.0 SCSI storage controller: Adaptec AHA-3960D / AIC-7899A U160/m (rev 01)
02:02.1 SCSI storage controller: Adaptec AHA-3960D / AIC-7899A U160/m (rev 01)
04:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet Controller (Copper) (rev 03)
04:00.3 Serial controller: Intel Corporation Active Management Technology - SOL (rev 03)
04:00.4 Serial bus controller [0c07]: Intel Corporation 82573E KCS (Active Management) (rev 03)
05:04.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)
05:05.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05)
[-- Attachment #7: lspci-v-v --]
[-- Type: application/octet-stream, Size: 20550 bytes --]
00:00.0 Host bridge: Intel Corporation E7230/3000/3010 Memory Controller Hub
Subsystem: Intel Corporation Unknown device 348d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e8200000-e82fffff
Prefetchable memory behind bridge: 00000000e8400000-00000000e84fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 1, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4159
Capabilities: [90] Subsystem: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 5, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4161
Capabilities: [90] Subsystem: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: e8100000-e81fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 6
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 6, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4169
Capabilities: [90] Subsystem: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 4080 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 4060 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 4040 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 4020 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at e8300400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: e8000000-e80fffff
Prefetchable memory behind bridge: 00000000e0000000-00000000e7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Intel Corporation Unknown device 348d
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 40b0 [size=16]
00:1f.2 RAID bus controller: Intel Corporation 82801GR/GH (ICH7 Family) Serial ATA Storage Controller RAID (rev 01)
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 1276
Region 0: I/O ports at 40c8 [size=8]
Region 1: I/O ports at 40e4 [size=4]
Region 2: I/O ports at 40c0 [size=8]
Region 3: I/O ports at 40e0 [size=4]
Region 4: I/O ports at 40a0 [size=16]
Region 5: Memory at e8300000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4189
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 4000 [size=32]
01:00.0 PCI bridge: Intel Corporation 6702PXH PCI Express-to-PCI Bridge A (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=02, subordinate=02, sec-latency=48
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e8200000-e82fffff
Prefetchable memory behind bridge: 00000000e8400000-00000000e84fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
Status: Dev=01:00.0 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=65535 CommitmentLimit=65535
Downstream: Capacity=65535 CommitmentLimit=65535
02:02.0 SCSI storage controller: Adaptec AHA-3960D / AIC-7899A U160/m (rev 01)
Subsystem: Adaptec AHA-3960D U160/m
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 35
BIST result: 00
Region 0: I/O ports at 3200 [disabled] [size=256]
Region 1: Memory at e8200000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at e8400000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:02.1 SCSI storage controller: Adaptec AHA-3960D / AIC-7899A U160/m (rev 01)
Subsystem: Adaptec AHA-3960D U160/m
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 36
BIST result: 00
Region 0: I/O ports at 3000 [disabled] [size=256]
Region 1: Memory at e8201000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at e8420000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet Controller (Copper) (rev 03)
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e8180000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at e8100000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at 2000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
04:00.3 Serial controller: Intel Corporation Active Management Technology - SOL (rev 03) (prog-if 02 [16550])
Subsystem: Intel Corporation Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 19
Region 0: I/O ports at 2020 [size=8]
Region 1: Memory at e81a1000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
04:00.4 Serial bus controller [0c07]: Intel Corporation 82573E KCS (Active Management) (rev 03) (prog-if 01)
Subsystem: Intel Corporation Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 11
Region 0: Memory at e81a0000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2028 [size=4]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
05:04.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) (prog-if 00 [VGA])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 1000 [size=256]
Region 2: Memory at e8040000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fffe0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:05.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05)
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e8020000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 1100 [size=64]
Expansion ROM at e8060000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: Fwd: Intel 82801G (ICH7) SATA port reset
2007-08-26 11:14 ` Fwd: Intel 82801G (ICH7) SATA port reset Joris
@ 2007-09-08 7:34 ` Tejun Heo
0 siblings, 0 replies; 2+ messages in thread
From: Tejun Heo @ 2007-09-08 7:34 UTC (permalink / raw)
To: Joris; +Cc: linux-ide
Joris wrote:
> Hello List,
>
>
> I have a rather annoying problem.
> On an Intel S3000AHLX
> (http://www.intel.com/design/servers/boards/s3000ah/index.htm)
> motherboard, I can't seem to utilize all SATA interfaces to the
> maximum.
> The first sata interface frequently resets every few seconds under
> heavy IO, the net result being ridiculous slow transfers (attach:
> dmesg_random_collection_of_errors)
>
> Running debian unstable and it's version of 2.6.22. System contains a
> xeon 3210 and an adaptec scsi controller from which I currently boot.
>
> There is little logic in the symptoms:
> * if there is no or light IO, no resets occur.
> * it's always the sda port that resets (changing cables or disks
> doesn't make a difference).
> * only specific combinations of disk-usage on the sata disks (attach:
> disk_combinations_causing_reset), just using sda alone does not cause
> resets.
> * reading is enough, writing is (subjectively) worse. dd
> if=/dev/sd{a,b,c,d} of=/dev/null & guarantees trouble.
> * when the port resets, the disk makes a clearly audible clicking noise
>
> I tried numerous things:
> * having the board exchanged with intel for the latest revision
> (thanks to my hardware supplier), updating to the latest bios and to a
> bios version 6 months old.
> * booting with older versions of the linux kernel, 2.6.18 and 2.6.21.
> * Using all possible combinations of the bios' matrix/lsi fakeraid and
> non-raid modes (always ignoring the "raid" and using the disks
> directly), and enable/disable the one PATA port in the bios.
> * asked seagate for a drive firmware update, to no avail.
>
>
> The only workable solution so far is to leave the first sata interface
> unused (remove the disk), which is obviously not a very nice solution.
>
> Any hints or suggestions would be welcome, I'd be more than happy to
> try out new things.
> things. I'm a bit at a loss on how to proceed at the moment.
Wheee... the link to sda is going up and down (PHY RDY changed) even
when sda itself isn't being accessed. I bet the clunking sound is head
doing emergency unloading. There are two possibilities: 1. the harddisk
is dying or 2. the power which gets fed to the drive sucks (ie.
fluctuates too much when other drives suck more power causing sda to do
emergency unload and PHY link loss.)
You can rule out #1 by exchanging disk positions. You can rule out #2
by connecting the harddrive to a separate PSU or exchanging power
connectors to different disks.
--
tejun
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2007-09-08 17:07 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <6b9952490708260411g22dede8ew6549acf0436b6e2e@mail.gmail.com>
2007-08-26 11:14 ` Fwd: Intel 82801G (ICH7) SATA port reset Joris
2007-09-08 7:34 ` Tejun Heo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).