From: Jeff Garzik <jeff@garzik.org>
To: IDE/ATA development list <linux-ide@vger.kernel.org>
Subject: linux-2.6.git error messages
Date: Tue, 16 Oct 2007 01:06:28 -0400 [thread overview]
Message-ID: <471446D4.6050803@garzik.org> (raw)
I get this on ICH5, modular kernel build:
libata version 3.00 loaded.
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata4294967295: failed to start port (errno=-19)
^^^^^^^^^^^^^
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata4294967295: failed to start port (errno=-19)
^^^^^^^^^^^^^
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ata_piix 0000:00:1f.1: version 2.12
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x24c0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x24c8 irq 15
ata1.00: ATA-5: MAXTOR 6L080J4, A93.0500, max UDMA/133
ata1.00: 156301488 sectors, multi 16: LBA
ata1.00: configured for UDMA/100
ata2.00: ATAPI: HL-DT-ST CD-ROM GCR-8480B, 1.00, max MWDMA2
ata2.00: configured for MWDMA2
scsi 0:0:0:0: Direct-Access ATA MAXTOR 6L080J4 A93. PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO
or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO
or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: CD-ROM HL-DT-ST CD-ROM GCR-8480B 1.00 PQ: 0 ANSI: 5
scsi 1:0:0:0: Attached scsi generic sg1 type 5
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0x24f0 ctl 0x2808 bmdma 0x24d0 irq 18
ata4: SATA max UDMA/133 cmd 0x24f8 ctl 0x280c bmdma 0x24d8 irq 18
ata4.00: ATA-6: ST380013AS, 3.05, max UDMA/133
ata4.00: 156301488 sectors, multi 16: LBA48
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access ATA ST380013AS 3.05 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO
or FUA
sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO
or FUA
sdb: sdb1 sdb2
sd 3:0:0:0: [sdb] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg2 type 0
sata_sil 0000:05:09.0: version 2.3
ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 18 (level, low) -> IRQ 18
scsi4 : sata_sil
scsi5 : sata_sil
ata5: SATA max UDMA/100 mmio m512@0xf0410000 tf 0xf0410080 irq 18
ata6: SATA max UDMA/100 mmio m512@0xf0410000 tf 0xf04100c0 irq 18
ata5: SATA link down (SStatus 0 SControl 310)
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: ATA-6: HDS722580VLSA80, V32OA60A, max UDMA/100
ata6.00: 160836480 sectors, multi 16: LBA48
ata6.00: configured for UDMA/100
scsi 5:0:0:0: Direct-Access ATA HDS722580VLSA80 V32O PQ: 0 ANSI: 5
sd 5:0:0:0: [sdc] 160836480 512-byte hardware sectors (82348 MB)
sd 5:0:0:0: [sdc] Write Protect is off
sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
support DPO
or FUA
sd 5:0:0:0: [sdc] 160836480 512-byte hardware sectors (82348 MB)
sd 5:0:0:0: [sdc] Write Protect is off
sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
support DPO
or FUA
sdc: sdc1 sdc2
sd 5:0:0:0: [sdc] Attached SCSI disk
sd 5:0:0:0: Attached scsi generic sg3 type 0
reply other threads:[~2007-10-16 5:06 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=471446D4.6050803@garzik.org \
--to=jeff@garzik.org \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).