From: Mark Paulus <mark.paulus@verizonbusiness.com>
To: Tejun Heo <htejun@gmail.com>
Cc: linux-ide@vger.kernel.org
Subject: Re: sata_sil issue on 2.6.22
Date: Fri, 30 Nov 2007 08:56:31 -0700 [thread overview]
Message-ID: <475032AF.6090001@verizonbusiness.com> (raw)
In-Reply-To: <474CC29E.8020102@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 7154 bytes --]
Tejun Heo wrote:
> Hello,
>
> Mark Paulus wrote:
>> sata_sil 0000:02:0b.0: version 2.2
>> ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 22 (level, low) -> IRQ 18
>> scsi0 : sata_sil
>> scsi1 : sata_sil
>> ata1: SATA max UDMA/100 cmd 0xe0812080 ctl 0xe081208a bmdma 0xe0812000
>> irq 18
>> ata2: SATA max UDMA/100 cmd 0xe08120c0 ctl 0xe08120ca bmdma 0xe0812008
>> irq 18
>> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>> ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
>> ata1.00: 19541088 sectors, multi 16: LBA ata1.00: applying bridge limits
>> ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
>> ata1.00: revalidation failed (errno=-5)
>> ata1: failed to recover some devices, retrying in 5 secs
>> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>> ata1.00: failed to set xfermode (err_mask=0x40)
>> ata1.00: limiting speed to UDMA/100:PIO3
>> ata1: failed to recover some devices, retrying in 5 secs
>> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
>> ata1.00: failed to set xfermode (err_mask=0x40)
>
> It looks like for some reason the port is being frozen repeatedly. Can
> you please apply the attached patch and post the dmesg?
>
> Thanks.
>
>
I applied the patch, and not much difference. Still the same issue, and here
is the new dmesg output.
SCSI subsystem initialized
libata version 2.21 loaded.
hda: Maxtor 34098H4, ATA DISK drive
hdb: WDC WD200BB-00DEA0, ATA DISK drive
hda: selected mode 0x45
hdb: selected mode 0x45
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: COMPAQ SC-148F, ATAPI CD/DVD-ROM drive
hdc: selected mode 0x22
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: UHCI Host Controller
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.4: irq 16, io base 0x00002440
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 17
e100: eth0: e100_probe: addr 0x41000000, irq 17, MAC addr 00:02:A5:10:5A:37
sata_sil 0000:02:0b.0: version 2.2
ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 22 (level, low) -> IRQ 18
scsi0 : sata_sil
scsi1 : sata_sil
ata1: SATA max UDMA/100 cmd 0xe0812080 ctl 0xe081208a bmdma 0xe0812000 irq 18
ata2: SATA max UDMA/100 cmd 0xe08120c0 ctl 0xe08120ca bmdma 0xe0812008 irq 18
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1: failed to recover some devices, retrying in 5 secs
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=4)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=3)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=2)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=1)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after 5 tries, giving up
ata1: EH complete
ata2: SATA link down (SStatus 0 SControl 310)
hda: max request size: 128KiB
hda: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 >
hdb: max request size: 128KiB
hdb: 39102336 sectors (20020 MB) w/8192KiB Cache, CHS=38792/16/63, UDMA(100)
hdb: cache flushes not supported
hdb: hdb1
hdc: ATAPI 48X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
--
Mark Paulus
2424 Garden of the Gods Rd | Phone: v622-5578 / 719-535-5578
0419/117 - LEC Access ; D5-1010 | FAX: 719-535-1665
Colo Springs, CO 80919 | 1800PageMCI / 1406052
AIM : mgpaulus1 / sametime : mark.paulus
[-- Attachment #2: mark_paulus.vcf --]
[-- Type: text/x-vcard, Size: 296 bytes --]
begin:vcard
fn:Mark Paulus
n:Paulus;Mark
org:MCI;Lec Interfaces / 40419
adr;dom:;;2424 Garden of the Gods Rd;Colorado Springs;CO;80919
email;internet:mark.paulus@verizonbusiness.com
title:Mark Paulus
tel;work:719-535-5578
tel;pager:800-pagemci / 1406052
tel;home:v622-5578
version:2.1
end:vcard
next prev parent reply other threads:[~2007-11-30 16:15 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-11-20 20:35 sata_sil issue on 2.6.22 Mark Paulus
2007-11-28 1:21 ` Tejun Heo
2007-11-30 15:56 ` Mark Paulus [this message]
2007-12-04 2:54 ` Tejun Heo
2007-12-05 14:29 ` Mark Paulus
2007-12-05 14:33 ` Tejun Heo
2007-12-05 14:49 ` Mark Paulus
2007-12-06 0:25 ` Tejun Heo
2007-12-06 2:10 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=475032AF.6090001@verizonbusiness.com \
--to=mark.paulus@verizonbusiness.com \
--cc=htejun@gmail.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).