* Re: question about sata-error on boot. [not found] <200711021934.21123.volker.armin.hemmann@tu-clausthal.de> @ 2007-11-07 6:15 ` Andrew Morton 2007-11-12 13:28 ` Tejun Heo 2007-12-07 13:32 ` Hemmann, Volker Armin 0 siblings, 2 replies; 4+ messages in thread From: Andrew Morton @ 2007-11-07 6:15 UTC (permalink / raw) To: Hemmann, Volker Armin; +Cc: linux-kernel, linux-ide > On Fri, 2 Nov 2007 19:34:20 +0100 "Hemmann, Volker Armin" <volker.armin.hemmann@tu-clausthal.de> wrote: > Hi, (cc linux-ide) > for some time (and I can't say for how long, but the board is less than a > month old) I get this error on boot: > > [ 42.116273] ahci 0000:00:0a.0: version 2.2 > [ 42.116482] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 > [ 42.116653] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 > (level, low) -> IRQ 23 > [ 43.119478] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf > impl IDE mode > [ 43.119778] ahci 0000:00:0a.0: flags: 64bit led clo pmp pio > [ 43.119943] PCI: Setting latency timer of device 0000:00:0a.0 to 64 > [ 43.120149] scsi0 : ahci > [ 43.120365] scsi1 : ahci > [ 43.120556] scsi2 : ahci > [ 43.120741] scsi3 : ahci > [ 43.120927] ata1: SATA max UDMA/133 cmd 0xffffc20000014100 ctl > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > [ 43.121227] ata2: SATA max UDMA/133 cmd 0xffffc20000014180 ctl > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > [ 43.121526] ata3: SATA max UDMA/133 cmd 0xffffc20000014200 ctl > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > [ 43.121826] ata4: SATA max UDMA/133 cmd 0xffffc20000014280 ctl > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > [ 43.934296] ata1: softreset failed (1st FIS failed) > [ 43.934461] ata1: reset failed (errno=-5), retrying in 10 secs > [ 53.885194] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > [ 53.885890] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 > [ 53.886056] ata1.00: 312581808 sectors, multi 16: LBA48 > [ 53.886804] ata1.00: configured for UDMA/133 > [ 54.201147] ata2: SATA link down (SStatus 0 SControl 300) > [ 54.517101] ata3: SATA link down (SStatus 0 SControl 300) > [ 54.833055] ata4: SATA link down (SStatus 0 SControl 300) > > The board has four ports and I use the first one. After that, the computer > boots and works fine. Harddisk-speed is normal. Kernel is 2.6.22.9 with > cfs&reiser4 patches. > > Is this something to worry about? > > Following is lspci -v and dmesg, config is attached. > lspci -v > 00:00.0 RAM memory: nVidia Corporation MCP65 Memory Controller (rev a1) > Subsystem: ASRock Incorporation Unknown device 0444 > Flags: bus master, 66MHz, fast devsel, latency 0 > Capabilities: [44] HyperTransport: Slave or Primary Interface > Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- > > 00:01.0 ISA bridge: nVidia Corporation MCP65 LPC Bridge (rev a2) > Subsystem: ASRock Incorporation Unknown device 0441 > Flags: bus master, 66MHz, fast devsel, latency 0 > I/O ports at 2f00 [size=256] > > 00:01.1 SMBus: nVidia Corporation MCP65 SMBus (rev a1) > Subsystem: ASRock Incorporation Unknown device 0446 > Flags: 66MHz, fast devsel, IRQ 11 > I/O ports at ac00 [size=64] > I/O ports at 2d00 [size=64] > I/O ports at 2e00 [size=64] > Capabilities: [44] Power Management version 2 > > 00:01.2 RAM memory: nVidia Corporation MCP65 Memory Controller (rev a1) > Subsystem: ASRock Incorporation Unknown device 0446 > Flags: 66MHz, fast devsel > > 00:02.0 USB Controller: nVidia Corporation MCP65 USB Controller (rev a1) > (prog-if 10 [OHCI]) > Subsystem: ASRock Incorporation Unknown device 0454 > Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 > Memory at f9dff000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [44] Power Management version 2 > > 00:02.1 USB Controller: nVidia Corporation MCP65 USB Controller (rev a1) > (prog-if 20 [EHCI]) > Subsystem: ASRock Incorporation Unknown device 0455 > Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 > Memory at f9dfec00 (32-bit, non-prefetchable) [size=256] > Capabilities: [44] Debug port > Capabilities: [80] Power Management version 2 > > 00:08.0 PCI bridge: nVidia Corporation MCP65 PCI bridge (rev a1) (prog-if 01 > [Subtractive decode]) > Flags: bus master, 66MHz, fast devsel, latency 0 > Bus: primary=00, secondary=02, subordinate=02, sec-latency=128 > I/O behind bridge: 0000c000-0000dfff > Memory behind bridge: f9f00000-f9ffffff > Prefetchable memory behind bridge: 88000000-880fffff > Capabilities: [b8] Subsystem: ASRock Incorporation Unknown device 0449 > Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- > > 00:09.0 IDE interface: nVidia Corporation MCP65 IDE (rev a1) (prog-if 8a > [Master SecP PriP]) > Subsystem: ASRock Incorporation Unknown device 0448 > Flags: bus master, 66MHz, fast devsel, latency 0 > [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] > [size=8] > [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] > [size=1] > [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] > [size=8] > [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] > [size=1] > I/O ports at ffa0 [size=16] > Capabilities: [44] Power Management version 2 > > 00:0a.0 IDE interface: nVidia Corporation MCP65 SATA Controller (rev a1) > (prog-if 85 [Master SecO PriO]) > Subsystem: ASRock Incorporation Unknown device 045d > Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 315 > I/O ports at 0e00 [size=8] > I/O ports at 0e20 [size=4] > I/O ports at 0e40 [size=8] > I/O ports at 0e60 [size=4] > I/O ports at 9800 [size=16] > Memory at f9dfc000 (32-bit, non-prefetchable) [size=8K] > Capabilities: [44] Power Management version 2 > Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ > Queue=0/3 Enable+ > Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ > > 00:0b.0 PCI bridge: nVidia Corporation Unknown device 045b (rev a1) (prog-if > 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 0000b000-0000bfff > Memory behind bridge: f9e00000-f9efffff > Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 045b > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ > Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- > Capabilities: [80] Express Root Port (Slot+), MSI 00 > > 00:0c.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1) > (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 045a > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ > Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- > Capabilities: [80] Express Root Port (Slot+), MSI 00 > > 00:0d.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1) > (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > I/O behind bridge: 0000e000-0000efff > Memory behind bridge: fa000000-febfffff > Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff > Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 0458 > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ > Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- > Capabilities: [80] Express Root Port (Slot+), MSI 00 > > 00:0e.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1) > (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 > Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 0459 > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ > Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- > Capabilities: [80] Express Root Port (Slot+), MSI 00 > > 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > HyperTransport Technology Configuration > Flags: fast devsel > Capabilities: [80] HyperTransport: Host or Secondary Interface > > 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Address Map > Flags: fast devsel > > 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM > Controller > Flags: fast devsel > > 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Miscellaneous Control > Flags: fast devsel > Capabilities: [f0] #0f [0010] > > 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI > Express Gigabit Ethernet controller (rev 01) > Subsystem: ASRock Incorporation Unknown device 8168 > Flags: bus master, fast devsel, latency 0, IRQ 19 > I/O ports at b800 [size=256] > Memory at f9eff000 (64-bit, non-prefetchable) [size=4K] > Expansion ROM at f9ec0000 [disabled] [size=128K] > Capabilities: [40] Power Management version 2 > Capabilities: [48] Vital Product Data > Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ > Queue=0/1 Enable- > Capabilities: [60] Express Endpoint, MSI 00 > Capabilities: [84] Vendor Specific Information > > 02:07.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 > Controller (PHY/Link) (prog-if 10 [OHCI]) > Subsystem: ASRock Incorporation Unknown device 8023 > Flags: bus master, medium devsel, latency 128, IRQ 11 > Memory at f9fff800 (32-bit, non-prefetchable) [size=2K] > Memory at f9ff8000 (32-bit, non-prefetchable) [size=16K] > Capabilities: [44] Power Management version 2 > > 02:08.0 SCSI storage controller: Adaptec AHA-2944UW / AIC-7884U (rev 01) > Subsystem: Adaptec Unknown device 7884 > Flags: bus master, medium devsel, latency 128, IRQ 5 > I/O ports at d800 [size=256] > Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K] > Expansion ROM at 88020000 [disabled] [size=64K] > Capabilities: [dc] Power Management version 1 > > 02:09.0 Multimedia audio controller: Creative Labs SB0400 Audigy2 Value > Subsystem: Creative Labs Unknown device 1001 > Flags: bus master, medium devsel, latency 128, IRQ 17 > I/O ports at dc00 [size=64] > Capabilities: [dc] Power Management version 2 > > 02:0a.0 Mass storage controller: HighPoint Technologies, Inc. > HPT366/368/370/370A/372/372N (rev 01) > Flags: bus master, medium devsel, latency 120, IRQ 18 > I/O ports at d480 [size=8] > I/O ports at d400 [size=4] > I/O ports at d000 [size=256] > Expansion ROM at 88000000 [disabled by cmd] [size=128K] > > 02:0a.1 Mass storage controller: HighPoint Technologies, Inc. > HPT366/368/370/370A/372/372N (rev 01) > Flags: bus master, medium devsel, latency 120, IRQ 18 > I/O ports at cc00 [size=8] > I/O ports at c880 [size=4] > I/O ports at c400 [size=256] > > 04:00.0 VGA compatible controller: nVidia Corporation GeForce 8600 GT (rev a1) > (prog-if 00 [VGA]) > Subsystem: nVidia Corporation Unknown device 0439 > Flags: bus master, fast devsel, latency 0, IRQ 16 > Memory at fd000000 (32-bit, non-prefetchable) [size=16M] > Memory at d0000000 (64-bit, prefetchable) [size=256M] > Memory at fa000000 (64-bit, non-prefetchable) [size=32M] > I/O ports at ec00 [size=128] > [virtual] Expansion ROM at febe0000 [disabled] [size=128K] > Capabilities: [60] Power Management version 2 > Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ > Queue=0/0 Enable- > Capabilities: [78] Express Endpoint, MSI 0 > > dmesg: > [ 0.000000] Linux version 2.6.22.9-cfs-v22reiser4 (root@energy) (gcc > version 4.2.2 (Gentoo 4.2.2 p1.0)) #5 SMP Thu Oct 25 14:39:54 CEST 2007 > [ 0.000000] Command line: root=/dev/sda3 nmi_watchdog=0 > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) > [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable) > [ 0.000000] BIOS-e820: 000000007ffb0000 - 000000007ffc0000 (ACPI data) > [ 0.000000] BIOS-e820: 000000007ffc0000 - 000000007fff0000 (ACPI NVS) > [ 0.000000] BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved) > [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) > [ 0.000000] BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved) > [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used > [ 0.000000] Entering add_active_range(0, 256, 524208) 1 entries of 256 used > [ 0.000000] end_pfn_map = 1048576 > [ 0.000000] DMI present. > [ 0.000000] ACPI: RSDP 000FA530, 0014 (r0 ACPIAM) > [ 0.000000] ACPI: RSDT 7FFB0000, 003C (r1 A M I OEMRSDT 9000720 MSFT > 97) > [ 0.000000] ACPI: FACP 7FFB0200, 0084 (r2 A_M_I OEMFACP 12000601 MSFT > 97) > [ 0.000000] ACPI: DSDT 7FFB0450, 4FFA (r1 ASR19 ASR1915A 15A INTL > 20051117) > [ 0.000000] ACPI: FACS 7FFC0000, 0040 > [ 0.000000] ACPI: APIC 7FFB0390, 0080 (r1 A M I OEMAPIC 9000720 MSFT > 97) > [ 0.000000] ACPI: MCFG 7FFB0410, 003C (r1 A M I OEMMCFG 9000720 MSFT > 97) > [ 0.000000] ACPI: OEMB 7FFC0040, 0060 (r1 A M I AMI_OEM 9000720 MSFT > 97) > [ 0.000000] ACPI: HPET 7FFB5450, 0038 (r1 A M I OEMHPET0 9000720 MSFT > 97) > [ 0.000000] ACPI: SSDT 7FFB5490, 030E (r1 A M I POWERNOW 1 AMD > 1) > [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used > [ 0.000000] Entering add_active_range(0, 256, 524208) 1 entries of 256 used > [ 0.000000] No mptable found. > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0 -> 4096 > [ 0.000000] DMA32 4096 -> 1048576 > [ 0.000000] Normal 1048576 -> 1048576 > [ 0.000000] early_node_map[2] active PFN ranges > [ 0.000000] 0: 0 -> 159 > [ 0.000000] 0: 256 -> 524208 > [ 0.000000] On node 0 totalpages: 524111 > [ 0.000000] DMA zone: 56 pages used for memmap > [ 0.000000] DMA zone: 905 pages reserved > [ 0.000000] DMA zone: 3038 pages, LIFO batch:0 > [ 0.000000] DMA32 zone: 7110 pages used for memmap > [ 0.000000] DMA32 zone: 513002 pages, LIFO batch:31 > [ 0.000000] Normal zone: 0 pages used for memmap > [ 0.000000] ACPI: PM-Timer IO Port: 0x2008 > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > [ 0.000000] Processor #0 (Bootup-CPU) > [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) > [ 0.000000] Processor #1 > [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) > [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) > [ 0.000000] ACPI: IRQ0 used by override. > [ 0.000000] ACPI: IRQ2 used by override. > [ 0.000000] ACPI: IRQ9 used by override. > [ 0.000000] ACPI: IRQ14 used by override. > [ 0.000000] ACPI: IRQ15 used by override. > [ 0.000000] Setting APIC routing to flat > [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000 > [ 0.000000] Using ACPI (MADT) for SMP configuration information > [ 0.000000] Allocating PCI resources starting at 88000000 (gap: > 80000000:7ec00000) > [ 0.000000] PERCPU: Allocating 29336 bytes of per cpu data > [ 0.000000] Built 1 zonelists. Total pages: 516040 > [ 0.000000] Kernel command line: root=/dev/sda3 nmi_watchdog=0 > [ 0.000000] Initializing CPU#0 > [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) > [ 0.000000] Marking TSC unstable due to TSCs unsynchronized > [ 40.731282] time.c: Detected 3013.892 MHz processor. > [ 40.735511] Console: colour VGA+ 80x25 > [ 40.745472] Dentry cache hash table entries: 262144 (order: 9, 2097152 > bytes) > [ 40.746781] Inode-cache hash table entries: 131072 (order: 8, 1048576 > bytes) > [ 40.747137] Checking aperture... > [ 40.747300] CPU 0: aperture @ ecc8000000 size 32 MB > [ 40.747464] Aperture too small (32 MB) > [ 40.753296] No AGP bridge found > [ 40.765569] Memory: 2060372k/2096832k available (2200k kernel code, 35792k > reserved, 669k data, 184k init) > [ 40.847841] Calibrating delay using timer specific routine.. 6034.57 > BogoMIPS (lpj=10053716) > [ 40.848202] Mount-cache hash table entries: 256 > [ 40.848437] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 > bytes/line) > [ 40.848602] CPU: L2 Cache: 1024K (64 bytes/line) > [ 40.848766] CPU: Physical Processor ID: 0 > [ 40.848928] CPU: Processor Core ID: 0 > [ 40.849103] Freeing SMP alternatives: 26k freed > [ 40.849613] ACPI: Core revision 20070126 > [ 40.884963] Using local APIC timer interrupts. > [ 40.918232] result 12557891 > [ 40.918393] Detected 12.557 MHz APIC timer. > [ 40.921062] Booting processor 1/2 APIC 0x1 > [ 40.931358] Initializing CPU#1 > [ 41.014213] Calibrating delay using timer specific routine.. 6030.95 > BogoMIPS (lpj=10046323) > [ 41.014218] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 > bytes/line) > [ 41.014219] CPU: L2 Cache: 1024K (64 bytes/line) > [ 41.014221] CPU: Physical Processor ID: 0 > [ 41.014222] CPU: Processor Core ID: 1 > [ 41.014303] AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ stepping 03 > [ 41.017460] Brought up 2 CPUs > [ 41.019044] NET: Registered protocol family 16 > [ 41.019258] ACPI: bus type pci registered > [ 41.019428] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved > [ 41.019592] PCI: Not using MMCONFIG. > [ 41.019755] PCI: Using configuration type 1 > [ 41.024096] ACPI: Interpreter enabled > [ 41.024259] ACPI: Using IOAPIC for interrupt routing > [ 41.024586] Error attaching device data > [ 41.024751] Error attaching device data > [ 41.024916] Error attaching device data > [ 41.025082] Error attaching device data > [ 41.031242] ACPI: PCI Root Bridge [PCI0] (0000:00) > [ 41.031413] PCI: Probing PCI hardware (bus 00) > [ 41.031942] PCI: Transparent bridge - 0000:00:08.0 > [ 41.032367] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > [ 41.032524] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] > [ 41.032638] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT] > [ 41.032705] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT] > [ 41.032771] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT] > [ 41.032836] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT] > [ 41.037361] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *5 > [ 41.037882] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10 > [ 41.038385] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *10 > [ 41.038888] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *11 > [ 41.039391] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, > disabled. > [ 41.039923] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10 > [ 41.040426] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, > disabled. > [ 41.040972] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *10 > [ 41.041475] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *5 > [ 41.041978] ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *0, > disabled. > [ 41.042510] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7 > [ 41.043012] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, > disabled. > [ 41.043544] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *0, > disabled. > [ 41.044088] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11 > [ 41.044593] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, > disabled. > [ 41.045126] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15 > [ 41.045630] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, > disabled. > [ 41.046189] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, > disabled. > [ 41.046722] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *0, > disabled. > [ 41.047255] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *0, > disabled. > [ 41.047708] Linux Plug and Play Support v0.97 (c) Adam Belay > [ 41.047879] pnp: PnP ACPI init > [ 41.048045] ACPI: bus type pnp registered > [ 41.051043] pnp: PnP ACPI: found 13 devices > [ 41.051205] ACPI: ACPI bus type pnp unregistered > [ 41.051432] SCSI subsystem initialized > [ 41.051618] libata version 2.21 loaded. > [ 41.051654] usbcore: registered new interface driver usbfs > [ 41.051834] usbcore: registered new interface driver hub > [ 41.052016] usbcore: registered new device driver usb > [ 41.052197] PCI: Using ACPI for IRQ routing > [ 41.052360] PCI: If a device doesn't work, try "pci=routeirq". If it > helps, post a report > [ 41.052747] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31 > [ 41.053027] hpet0: 3 32-bit timers, 25000000 Hz > [ 41.054255] pnp: 00:05: iomem range 0x0-0x0 could not be reserved > [ 41.054421] pnp: 00:05: iomem range 0xfee01000-0xfeefffff has been reserved > [ 41.054589] pnp: 00:07: iomem range 0xfec00000-0xfec00fff could not be > reserved > [ 41.054886] pnp: 00:07: iomem range 0xfee00000-0xfee00fff could not be > reserved > [ 41.055185] pnp: 00:0a: ioport range 0x290-0x29f has been reserved > [ 41.055351] pnp: 00:0b: iomem range 0xe0000000-0xefffffff has been reserved > [ 41.055519] pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved > [ 41.055685] pnp: 00:0c: iomem range 0xc0000-0xcffff has been reserved > [ 41.055850] pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved > [ 41.056017] pnp: 00:0c: iomem range 0x100000-0x7fffffff could not be > reserved > [ 41.056338] PCI: Bridge: 0000:00:08.0 > [ 41.056501] IO window: c000-dfff > [ 41.056664] MEM window: f9f00000-f9ffffff > [ 41.056829] PREFETCH window: 88000000-880fffff > [ 41.056993] PCI: Bridge: 0000:00:0b.0 > [ 41.057156] IO window: b000-bfff > [ 41.057319] MEM window: f9e00000-f9efffff > [ 41.057451] Time: hpet clocksource has been installed. > [ 41.057645] PREFETCH window: disabled. > [ 41.057808] PCI: Bridge: 0000:00:0c.0 > [ 41.057970] IO window: disabled. > [ 41.058132] MEM window: disabled. > [ 41.058294] PREFETCH window: disabled. > [ 41.058457] PCI: Bridge: 0000:00:0d.0 > [ 41.058619] IO window: e000-efff > [ 41.058783] MEM window: fa000000-febfffff > [ 41.058946] PREFETCH window: d0000000-dfffffff > [ 41.059110] PCI: Bridge: 0000:00:0e.0 > [ 41.059272] IO window: disabled. > [ 41.059434] MEM window: disabled. > [ 41.059596] PREFETCH window: disabled. > [ 41.059765] PCI: Setting latency timer of device 0000:00:08.0 to 64 > [ 41.059770] PCI: Setting latency timer of device 0000:00:0b.0 to 64 > [ 41.059774] PCI: Setting latency timer of device 0000:00:0c.0 to 64 > [ 41.059778] PCI: Setting latency timer of device 0000:00:0d.0 to 64 > [ 41.059783] PCI: Setting latency timer of device 0000:00:0e.0 to 64 > [ 41.059801] NET: Registered protocol family 2 > [ 41.100619] IP route cache hash table entries: 65536 (order: 7, 524288 > bytes) > [ 41.101145] TCP established hash table entries: 131072 (order: 9, 3145728 > bytes) > [ 41.102591] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) > [ 41.103136] TCP: Hash tables configured (established 131072 bind 65536) > [ 41.103302] TCP reno registered > [ 41.114592] Total HugeTLB memory allocated, 0 > [ 41.114825] Loading Reiser4. See www.namesys.com for a description of > Reiser4. > [ 41.115182] io scheduler noop registered > [ 41.115352] io scheduler cfq registered (default) > [ 41.116320] Boot video device is 0000:04:00.0 > [ 41.116435] PCI: Setting latency timer of device 0000:00:0b.0 to 64 > [ 41.116450] assign_interrupt_mode Found MSI capability > [ 41.116629] Allocate Port Service[0000:00:0b.0:pcie00] > [ 41.116670] PCI: Setting latency timer of device 0000:00:0c.0 to 64 > [ 41.116685] assign_interrupt_mode Found MSI capability > [ 41.116857] Allocate Port Service[0000:00:0c.0:pcie00] > [ 41.116893] PCI: Setting latency timer of device 0000:00:0d.0 to 64 > [ 41.116908] assign_interrupt_mode Found MSI capability > [ 41.117080] Allocate Port Service[0000:00:0d.0:pcie00] > [ 41.117117] PCI: Setting latency timer of device 0000:00:0e.0 to 64 > [ 41.117135] assign_interrupt_mode Found MSI capability > [ 41.120561] Allocate Port Service[0000:00:0e.0:pcie00] > [ 41.120731] input: Power Button (FF) as /class/input/input0 > [ 41.120895] ACPI: Power Button (FF) [PWRF] > [ 41.121116] input: Power Button (CM) as /class/input/input1 > [ 41.121279] ACPI: Power Button (CM) [PWRB] > [ 41.140593] Real Time Clock Driver v1.12ac > [ 41.140939] hpet_resources: 0xfed00000 is busy > [ 41.140970] Linux agpgart interface v0.102 (c) Dave Jones > [ 41.141204] tun: Universal TUN/TAP device driver, 1.6 > [ 41.141367] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> > [ 41.141551] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > [ 41.141716] ide: Assuming 33MHz system bus speed for PIO modes; override > with idebus=xx > [ 41.142031] NFORCE-MCP65: IDE controller at PCI slot 0000:00:09.0 > [ 41.142207] NFORCE-MCP65: chipset revision 161 > [ 41.142371] NFORCE-MCP65: not 100% native mode: will probe irqs later > [ 41.142539] NFORCE-MCP65: 0000:00:09.0 (rev a1) UDMA133 controller > [ 41.142706] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, > hdb:pio > [ 41.143065] Probing IDE interface ide0... > [ 41.430036] hda: SAMSUNG SP1213N, ATA DISK drive > [ 42.071954] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > [ 42.074576] hda: max request size: 512KiB > [ 42.074789] hda: 234493056 sectors (120060 MB) w/8192KiB Cache, > CHS=16383/255/63, UDMA(100) > [ 42.075551] hda: cache flushes supported > [ 42.075734] hda: hda1 hda2 hda3 < hda5 hda6 hda7 > > [ 42.116273] ahci 0000:00:0a.0: version 2.2 > [ 42.116482] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 > [ 42.116653] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 > (level, low) -> IRQ 23 > [ 43.119478] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf > impl IDE mode > [ 43.119778] ahci 0000:00:0a.0: flags: 64bit led clo pmp pio > [ 43.119943] PCI: Setting latency timer of device 0000:00:0a.0 to 64 > [ 43.120149] scsi0 : ahci > [ 43.120365] scsi1 : ahci > [ 43.120556] scsi2 : ahci > [ 43.120741] scsi3 : ahci > [ 43.120927] ata1: SATA max UDMA/133 cmd 0xffffc20000014100 ctl > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > [ 43.121227] ata2: SATA max UDMA/133 cmd 0xffffc20000014180 ctl > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > [ 43.121526] ata3: SATA max UDMA/133 cmd 0xffffc20000014200 ctl > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > [ 43.121826] ata4: SATA max UDMA/133 cmd 0xffffc20000014280 ctl > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > [ 43.934296] ata1: softreset failed (1st FIS failed) > [ 43.934461] ata1: reset failed (errno=-5), retrying in 10 secs > [ 53.885194] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > [ 53.885890] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 > [ 53.886056] ata1.00: 312581808 sectors, multi 16: LBA48 > [ 53.886804] ata1.00: configured for UDMA/133 > [ 54.201147] ata2: SATA link down (SStatus 0 SControl 300) > [ 54.517101] ata3: SATA link down (SStatus 0 SControl 300) > [ 54.833055] ata4: SATA link down (SStatus 0 SControl 300) > [ 54.833271] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 > PQ: 0 ANSI: 5 > [ 54.833623] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 > MB) > [ 54.833793] sd 0:0:0:0: [sda] Write Protect is off > [ 54.833957] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 54.833965] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, > doesn't support DPO or FUA > [ 54.834287] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 > MB) > [ 54.834455] sd 0:0:0:0: [sda] Write Protect is off > [ 54.834619] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 54.834626] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, > doesn't support DPO or FUA > [ 54.834924] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > > [ 54.869055] sd 0:0:0:0: [sda] Attached SCSI disk > [ 54.869495] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22 > [ 54.869667] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 22 > (level, low) -> IRQ 22 > [ 54.870288] PCI: Setting latency timer of device 0000:00:02.1 to 64 > [ 54.870293] ehci_hcd 0000:00:02.1: EHCI Host Controller > [ 54.870532] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus > number 1 > [ 54.870848] ehci_hcd 0000:00:02.1: debug port 1 > [ 54.871013] PCI: cache line size of 64 is not supported by device > 0000:00:02.1 > [ 54.871022] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf9dfec00 > [ 54.871191] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 > Dec 2004 > [ 54.871572] usb usb1: configuration #1 chosen from 1 choice > [ 54.871761] hub 1-0:1.0: USB hub found > [ 54.871927] hub 1-0:1.0: 10 ports detected > [ 54.976112] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) > Driver > [ 54.976353] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21 > [ 54.976523] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 21 > (level, low) -> IRQ 21 > [ 54.977020] PCI: Setting latency timer of device 0000:00:02.0 to 64 > [ 54.977025] ohci_hcd 0000:00:02.0: OHCI Host Controller > [ 54.977260] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus > number 2 > [ 54.977569] ohci_hcd 0000:00:02.0: irq 21, io mem 0xf9dff000 > [ 55.034680] usb usb2: configuration #1 chosen from 1 choice > [ 55.034869] hub 2-0:1.0: USB hub found > [ 55.035037] hub 2-0:1.0: 10 ports detected > [ 55.139122] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 > irq 1,12 > [ 55.142186] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 55.142352] serio: i8042 AUX port at 0x60,0x64 irq 12 > [ 55.142569] mice: PS/2 mouse device common for all mice > [ 55.169330] input: AT Translated Set 2 keyboard as /class/input/input2 > [ 55.431622] usb 1-5: new high speed USB device using ehci_hcd and address 3 > [ 55.566822] usb 1-5: configuration #1 chosen from 1 choice > [ 55.807525] usb 2-4: new full speed USB device using ohci_hcd and address 2 > [ 55.963577] usb 2-4: configuration #1 chosen from 1 choice > [ 55.969539] hub 2-4:1.0: USB hub found > [ 55.972507] hub 2-4:1.0: 4 ports detected > [ 56.314740] usb 2-4.1: new full speed USB device using ohci_hcd and address > 3 > [ 56.449493] usb 2-4.1: configuration #1 chosen from 1 choice > [ 56.669944] usb 2-4.3: new low speed USB device using ohci_hcd and address > 4 > [ 56.783741] usb 2-4.3: configuration #1 chosen from 1 choice > [ 56.802767] input: Logitech USB-PS/2 Optical Mouse as /class/input/input3 > [ 56.802968] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on > usb-0000:00:02.0-4.3 > [ 56.803327] usbcore: registered new interface driver usbhid > [ 56.803492] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver > [ 56.803690] TCP cubic registered > [ 56.803861] NET: Registered protocol family 1 > [ 56.804026] NET: Registered protocol family 17 > [ 56.804201] powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor > 6000+ processors (version 2.00.00) > [ 56.804448] powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x6 > [ 56.804613] powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0x8 > [ 56.804778] powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xa > [ 56.804943] powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xc > [ 56.805107] powernow-k8: 4 : fid 0xe (2200 MHz), vid 0xe > [ 56.805272] powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 > [ 56.805437] powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 > [ 56.805602] powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 > [ 56.826551] ReiserFS: sda3: found reiserfs format "3.6" with standard > journal > [ 56.826720] ReiserFS: sda3: using ordered data mode > [ 56.836124] ReiserFS: sda3: journal params: device sda3, size 8192, journal > first block 18, max trans len 1024, max batch 900, max commit age 30, max > trans age 30 > [ 56.837467] ReiserFS: sda3: checking transaction log (sda3) > [ 56.888740] ReiserFS: sda3: Using r5 hash to sort names > [ 56.888915] VFS: Mounted root (reiserfs filesystem) readonly. > [ 56.889092] Freeing unused kernel memory: 184k freed > [ 61.840593] ReiserFS: sda3: switching to journaled data mode > [ 62.230945] r8169 Gigabit Ethernet driver 2.2LK loaded > [ 62.231224] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19 > [ 62.231232] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19 > (level, low) -> IRQ 19 > [ 62.231250] PCI: Setting latency timer of device 0000:01:00.0 to 64 > [ 62.231430] eth0: RTL8168b/8111b at 0xffffc2000016c000, 00:19:66:47:f3:cb, > IRQ 19 > [ 62.284221] HPT366: IDE controller at PCI slot 0000:02:0a.0 > [ 62.284491] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18 > [ 62.284499] ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKC] -> GSI 18 > (level, low) -> IRQ 18 > [ 62.284508] HPT366: chipset revision 1 > [ 62.284514] HPT366: using 33 MHz PCI clock > [ 62.284516] HPT366: 100% native mode on irq 18 > [ 62.284524] ide1: BM-DMA at 0xd000-0xd007, BIOS settings: hdc:pio, > hdd:pio > [ 62.284536] ACPI: PCI Interrupt 0000:02:0a.1[A] -> Link [LNKC] -> GSI 18 > (level, low) -> IRQ 18 > [ 62.284544] HPT366: using 33 MHz PCI clock > [ 62.284546] HPT366: too many IDE interfaces, no room in table > [ 62.284548] HPT366: neither IDE port enabled (BIOS) > [ 62.284551] Probing IDE interface ide1... > [ 62.988343] hdc: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive > [ 63.630192] ide1 at 0xd480-0xd487,0xd402 on irq 18 > [ 63.632589] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache > [ 63.632594] Uniform CD-ROM driver Revision: 3.20 > [ 64.048482] reiser4: sda5: found disk format 4.0.0. > [ 69.431516] reiser4: sda6: found disk format 4.0.0. > [ 70.722395] reiser4: hda7: found disk format 4.0.0. > [ 71.428725] Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1 > across:1951888k > [ 74.227887] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17 > [ 74.227897] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 17 > (level, low) -> IRQ 17 > [ 74.230613] Audigy2 value: Special config. > [ 78.048887] r8169: eth0: link up > [ 78.049039] r8169: eth0: link up > [ 82.597555] nvidia: module license 'NVIDIA' taints kernel. > [ 82.767839] ACPI: PCI Interrupt Link [LNED] enabled at IRQ 16 > [ 82.767847] ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNED] -> GSI 16 > (level, low) -> IRQ 16 > [ 82.767853] PCI: Setting latency timer of device 0000:04:00.0 to 64 > [ 82.767943] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.23 Thu > Oct 4 10:27:34 PDT 2007 > > Glück Auf, > Volker > ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: question about sata-error on boot. 2007-11-07 6:15 ` question about sata-error on boot Andrew Morton @ 2007-11-12 13:28 ` Tejun Heo 2007-12-07 13:32 ` Hemmann, Volker Armin 1 sibling, 0 replies; 4+ messages in thread From: Tejun Heo @ 2007-11-12 13:28 UTC (permalink / raw) To: Andrew Morton; +Cc: Hemmann, Volker Armin, linux-kernel, linux-ide, hancockr (cc Robert Hancock, maybe we need ATA_LFLAG_HRST_TO_RESUME for these controllers?) Andrew Morton wrote: >> On Fri, 2 Nov 2007 19:34:20 +0100 "Hemmann, Volker Armin" <volker.armin.hemmann@tu-clausthal.de> wrote: >> Hi, > > (cc linux-ide) > >> for some time (and I can't say for how long, but the board is less than a >> month old) I get this error on boot: >> >> [ 42.116273] ahci 0000:00:0a.0: version 2.2 >> [ 42.116482] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 >> [ 42.116653] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 >> (level, low) -> IRQ 23 >> [ 43.119478] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf >> impl IDE mode >> [ 43.119778] ahci 0000:00:0a.0: flags: 64bit led clo pmp pio >> [ 43.119943] PCI: Setting latency timer of device 0000:00:0a.0 to 64 >> [ 43.120149] scsi0 : ahci >> [ 43.120365] scsi1 : ahci >> [ 43.120556] scsi2 : ahci >> [ 43.120741] scsi3 : ahci >> [ 43.120927] ata1: SATA max UDMA/133 cmd 0xffffc20000014100 ctl >> 0x0000000000000000 bmdma 0x0000000000000000 irq 315 >> [ 43.121227] ata2: SATA max UDMA/133 cmd 0xffffc20000014180 ctl >> 0x0000000000000000 bmdma 0x0000000000000000 irq 315 >> [ 43.121526] ata3: SATA max UDMA/133 cmd 0xffffc20000014200 ctl >> 0x0000000000000000 bmdma 0x0000000000000000 irq 315 >> [ 43.121826] ata4: SATA max UDMA/133 cmd 0xffffc20000014280 ctl >> 0x0000000000000000 bmdma 0x0000000000000000 irq 315 >> [ 43.934296] ata1: softreset failed (1st FIS failed) >> [ 43.934461] ata1: reset failed (errno=-5), retrying in 10 secs >> [ 53.885194] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >> [ 53.885890] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 >> [ 53.886056] ata1.00: 312581808 sectors, multi 16: LBA48 >> [ 53.886804] ata1.00: configured for UDMA/133 >> [ 54.201147] ata2: SATA link down (SStatus 0 SControl 300) >> [ 54.517101] ata3: SATA link down (SStatus 0 SControl 300) >> [ 54.833055] ata4: SATA link down (SStatus 0 SControl 300) >> >> The board has four ports and I use the first one. After that, the computer >> boots and works fine. Harddisk-speed is normal. Kernel is 2.6.22.9 with >> cfs&reiser4 patches. >> >> Is this something to worry about? >> >> Following is lspci -v and dmesg, config is attached. >> lspci -v >> 00:00.0 RAM memory: nVidia Corporation MCP65 Memory Controller (rev a1) >> Subsystem: ASRock Incorporation Unknown device 0444 >> Flags: bus master, 66MHz, fast devsel, latency 0 >> Capabilities: [44] HyperTransport: Slave or Primary Interface >> Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- >> >> 00:01.0 ISA bridge: nVidia Corporation MCP65 LPC Bridge (rev a2) >> Subsystem: ASRock Incorporation Unknown device 0441 >> Flags: bus master, 66MHz, fast devsel, latency 0 >> I/O ports at 2f00 [size=256] >> >> 00:01.1 SMBus: nVidia Corporation MCP65 SMBus (rev a1) >> Subsystem: ASRock Incorporation Unknown device 0446 >> Flags: 66MHz, fast devsel, IRQ 11 >> I/O ports at ac00 [size=64] >> I/O ports at 2d00 [size=64] >> I/O ports at 2e00 [size=64] >> Capabilities: [44] Power Management version 2 >> >> 00:01.2 RAM memory: nVidia Corporation MCP65 Memory Controller (rev a1) >> Subsystem: ASRock Incorporation Unknown device 0446 >> Flags: 66MHz, fast devsel >> >> 00:02.0 USB Controller: nVidia Corporation MCP65 USB Controller (rev a1) >> (prog-if 10 [OHCI]) >> Subsystem: ASRock Incorporation Unknown device 0454 >> Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 >> Memory at f9dff000 (32-bit, non-prefetchable) [size=4K] >> Capabilities: [44] Power Management version 2 >> >> 00:02.1 USB Controller: nVidia Corporation MCP65 USB Controller (rev a1) >> (prog-if 20 [EHCI]) >> Subsystem: ASRock Incorporation Unknown device 0455 >> Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 >> Memory at f9dfec00 (32-bit, non-prefetchable) [size=256] >> Capabilities: [44] Debug port >> Capabilities: [80] Power Management version 2 >> >> 00:08.0 PCI bridge: nVidia Corporation MCP65 PCI bridge (rev a1) (prog-if 01 >> [Subtractive decode]) >> Flags: bus master, 66MHz, fast devsel, latency 0 >> Bus: primary=00, secondary=02, subordinate=02, sec-latency=128 >> I/O behind bridge: 0000c000-0000dfff >> Memory behind bridge: f9f00000-f9ffffff >> Prefetchable memory behind bridge: 88000000-880fffff >> Capabilities: [b8] Subsystem: ASRock Incorporation Unknown device 0449 >> Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- >> >> 00:09.0 IDE interface: nVidia Corporation MCP65 IDE (rev a1) (prog-if 8a >> [Master SecP PriP]) >> Subsystem: ASRock Incorporation Unknown device 0448 >> Flags: bus master, 66MHz, fast devsel, latency 0 >> [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] >> [size=8] >> [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] >> [size=1] >> [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] >> [size=8] >> [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] >> [size=1] >> I/O ports at ffa0 [size=16] >> Capabilities: [44] Power Management version 2 >> >> 00:0a.0 IDE interface: nVidia Corporation MCP65 SATA Controller (rev a1) >> (prog-if 85 [Master SecO PriO]) >> Subsystem: ASRock Incorporation Unknown device 045d >> Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 315 >> I/O ports at 0e00 [size=8] >> I/O ports at 0e20 [size=4] >> I/O ports at 0e40 [size=8] >> I/O ports at 0e60 [size=4] >> I/O ports at 9800 [size=16] >> Memory at f9dfc000 (32-bit, non-prefetchable) [size=8K] >> Capabilities: [44] Power Management version 2 >> Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ >> Queue=0/3 Enable+ >> Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ >> >> 00:0b.0 PCI bridge: nVidia Corporation Unknown device 045b (rev a1) (prog-if >> 00 [Normal decode]) >> Flags: bus master, fast devsel, latency 0 >> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 >> I/O behind bridge: 0000b000-0000bfff >> Memory behind bridge: f9e00000-f9efffff >> Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 045b >> Capabilities: [48] Power Management version 2 >> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ >> Queue=0/1 Enable+ >> Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- >> Capabilities: [80] Express Root Port (Slot+), MSI 00 >> >> 00:0c.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1) >> (prog-if 00 [Normal decode]) >> Flags: bus master, fast devsel, latency 0 >> Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 >> Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 045a >> Capabilities: [48] Power Management version 2 >> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ >> Queue=0/1 Enable+ >> Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- >> Capabilities: [80] Express Root Port (Slot+), MSI 00 >> >> 00:0d.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1) >> (prog-if 00 [Normal decode]) >> Flags: bus master, fast devsel, latency 0 >> Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 >> I/O behind bridge: 0000e000-0000efff >> Memory behind bridge: fa000000-febfffff >> Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff >> Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 0458 >> Capabilities: [48] Power Management version 2 >> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ >> Queue=0/1 Enable+ >> Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- >> Capabilities: [80] Express Root Port (Slot+), MSI 00 >> >> 00:0e.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1) >> (prog-if 00 [Normal decode]) >> Flags: bus master, fast devsel, latency 0 >> Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 >> Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 0459 >> Capabilities: [48] Power Management version 2 >> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ >> Queue=0/1 Enable+ >> Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- >> Capabilities: [80] Express Root Port (Slot+), MSI 00 >> >> 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] >> HyperTransport Technology Configuration >> Flags: fast devsel >> Capabilities: [80] HyperTransport: Host or Secondary Interface >> >> 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] >> Address Map >> Flags: fast devsel >> >> 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM >> Controller >> Flags: fast devsel >> >> 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] >> Miscellaneous Control >> Flags: fast devsel >> Capabilities: [f0] #0f [0010] >> >> 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI >> Express Gigabit Ethernet controller (rev 01) >> Subsystem: ASRock Incorporation Unknown device 8168 >> Flags: bus master, fast devsel, latency 0, IRQ 19 >> I/O ports at b800 [size=256] >> Memory at f9eff000 (64-bit, non-prefetchable) [size=4K] >> Expansion ROM at f9ec0000 [disabled] [size=128K] >> Capabilities: [40] Power Management version 2 >> Capabilities: [48] Vital Product Data >> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ >> Queue=0/1 Enable- >> Capabilities: [60] Express Endpoint, MSI 00 >> Capabilities: [84] Vendor Specific Information >> >> 02:07.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 >> Controller (PHY/Link) (prog-if 10 [OHCI]) >> Subsystem: ASRock Incorporation Unknown device 8023 >> Flags: bus master, medium devsel, latency 128, IRQ 11 >> Memory at f9fff800 (32-bit, non-prefetchable) [size=2K] >> Memory at f9ff8000 (32-bit, non-prefetchable) [size=16K] >> Capabilities: [44] Power Management version 2 >> >> 02:08.0 SCSI storage controller: Adaptec AHA-2944UW / AIC-7884U (rev 01) >> Subsystem: Adaptec Unknown device 7884 >> Flags: bus master, medium devsel, latency 128, IRQ 5 >> I/O ports at d800 [size=256] >> Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K] >> Expansion ROM at 88020000 [disabled] [size=64K] >> Capabilities: [dc] Power Management version 1 >> >> 02:09.0 Multimedia audio controller: Creative Labs SB0400 Audigy2 Value >> Subsystem: Creative Labs Unknown device 1001 >> Flags: bus master, medium devsel, latency 128, IRQ 17 >> I/O ports at dc00 [size=64] >> Capabilities: [dc] Power Management version 2 >> >> 02:0a.0 Mass storage controller: HighPoint Technologies, Inc. >> HPT366/368/370/370A/372/372N (rev 01) >> Flags: bus master, medium devsel, latency 120, IRQ 18 >> I/O ports at d480 [size=8] >> I/O ports at d400 [size=4] >> I/O ports at d000 [size=256] >> Expansion ROM at 88000000 [disabled by cmd] [size=128K] >> >> 02:0a.1 Mass storage controller: HighPoint Technologies, Inc. >> HPT366/368/370/370A/372/372N (rev 01) >> Flags: bus master, medium devsel, latency 120, IRQ 18 >> I/O ports at cc00 [size=8] >> I/O ports at c880 [size=4] >> I/O ports at c400 [size=256] >> >> 04:00.0 VGA compatible controller: nVidia Corporation GeForce 8600 GT (rev a1) >> (prog-if 00 [VGA]) >> Subsystem: nVidia Corporation Unknown device 0439 >> Flags: bus master, fast devsel, latency 0, IRQ 16 >> Memory at fd000000 (32-bit, non-prefetchable) [size=16M] >> Memory at d0000000 (64-bit, prefetchable) [size=256M] >> Memory at fa000000 (64-bit, non-prefetchable) [size=32M] >> I/O ports at ec00 [size=128] >> [virtual] Expansion ROM at febe0000 [disabled] [size=128K] >> Capabilities: [60] Power Management version 2 >> Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ >> Queue=0/0 Enable- >> Capabilities: [78] Express Endpoint, MSI 0 >> >> dmesg: >> [ 0.000000] Linux version 2.6.22.9-cfs-v22reiser4 (root@energy) (gcc >> version 4.2.2 (Gentoo 4.2.2 p1.0)) #5 SMP Thu Oct 25 14:39:54 CEST 2007 >> [ 0.000000] Command line: root=/dev/sda3 nmi_watchdog=0 >> [ 0.000000] BIOS-provided physical RAM map: >> [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) >> [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) >> [ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) >> [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable) >> [ 0.000000] BIOS-e820: 000000007ffb0000 - 000000007ffc0000 (ACPI data) >> [ 0.000000] BIOS-e820: 000000007ffc0000 - 000000007fff0000 (ACPI NVS) >> [ 0.000000] BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved) >> [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) >> [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) >> [ 0.000000] BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved) >> [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used >> [ 0.000000] Entering add_active_range(0, 256, 524208) 1 entries of 256 used >> [ 0.000000] end_pfn_map = 1048576 >> [ 0.000000] DMI present. >> [ 0.000000] ACPI: RSDP 000FA530, 0014 (r0 ACPIAM) >> [ 0.000000] ACPI: RSDT 7FFB0000, 003C (r1 A M I OEMRSDT 9000720 MSFT >> 97) >> [ 0.000000] ACPI: FACP 7FFB0200, 0084 (r2 A_M_I OEMFACP 12000601 MSFT >> 97) >> [ 0.000000] ACPI: DSDT 7FFB0450, 4FFA (r1 ASR19 ASR1915A 15A INTL >> 20051117) >> [ 0.000000] ACPI: FACS 7FFC0000, 0040 >> [ 0.000000] ACPI: APIC 7FFB0390, 0080 (r1 A M I OEMAPIC 9000720 MSFT >> 97) >> [ 0.000000] ACPI: MCFG 7FFB0410, 003C (r1 A M I OEMMCFG 9000720 MSFT >> 97) >> [ 0.000000] ACPI: OEMB 7FFC0040, 0060 (r1 A M I AMI_OEM 9000720 MSFT >> 97) >> [ 0.000000] ACPI: HPET 7FFB5450, 0038 (r1 A M I OEMHPET0 9000720 MSFT >> 97) >> [ 0.000000] ACPI: SSDT 7FFB5490, 030E (r1 A M I POWERNOW 1 AMD >> 1) >> [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used >> [ 0.000000] Entering add_active_range(0, 256, 524208) 1 entries of 256 used >> [ 0.000000] No mptable found. >> [ 0.000000] Zone PFN ranges: >> [ 0.000000] DMA 0 -> 4096 >> [ 0.000000] DMA32 4096 -> 1048576 >> [ 0.000000] Normal 1048576 -> 1048576 >> [ 0.000000] early_node_map[2] active PFN ranges >> [ 0.000000] 0: 0 -> 159 >> [ 0.000000] 0: 256 -> 524208 >> [ 0.000000] On node 0 totalpages: 524111 >> [ 0.000000] DMA zone: 56 pages used for memmap >> [ 0.000000] DMA zone: 905 pages reserved >> [ 0.000000] DMA zone: 3038 pages, LIFO batch:0 >> [ 0.000000] DMA32 zone: 7110 pages used for memmap >> [ 0.000000] DMA32 zone: 513002 pages, LIFO batch:31 >> [ 0.000000] Normal zone: 0 pages used for memmap >> [ 0.000000] ACPI: PM-Timer IO Port: 0x2008 >> [ 0.000000] ACPI: Local APIC address 0xfee00000 >> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) >> [ 0.000000] Processor #0 (Bootup-CPU) >> [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) >> [ 0.000000] Processor #1 >> [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) >> [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) >> [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) >> [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 >> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) >> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) >> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) >> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) >> [ 0.000000] ACPI: IRQ0 used by override. >> [ 0.000000] ACPI: IRQ2 used by override. >> [ 0.000000] ACPI: IRQ9 used by override. >> [ 0.000000] ACPI: IRQ14 used by override. >> [ 0.000000] ACPI: IRQ15 used by override. >> [ 0.000000] Setting APIC routing to flat >> [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000 >> [ 0.000000] Using ACPI (MADT) for SMP configuration information >> [ 0.000000] Allocating PCI resources starting at 88000000 (gap: >> 80000000:7ec00000) >> [ 0.000000] PERCPU: Allocating 29336 bytes of per cpu data >> [ 0.000000] Built 1 zonelists. Total pages: 516040 >> [ 0.000000] Kernel command line: root=/dev/sda3 nmi_watchdog=0 >> [ 0.000000] Initializing CPU#0 >> [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) >> [ 0.000000] Marking TSC unstable due to TSCs unsynchronized >> [ 40.731282] time.c: Detected 3013.892 MHz processor. >> [ 40.735511] Console: colour VGA+ 80x25 >> [ 40.745472] Dentry cache hash table entries: 262144 (order: 9, 2097152 >> bytes) >> [ 40.746781] Inode-cache hash table entries: 131072 (order: 8, 1048576 >> bytes) >> [ 40.747137] Checking aperture... >> [ 40.747300] CPU 0: aperture @ ecc8000000 size 32 MB >> [ 40.747464] Aperture too small (32 MB) >> [ 40.753296] No AGP bridge found >> [ 40.765569] Memory: 2060372k/2096832k available (2200k kernel code, 35792k >> reserved, 669k data, 184k init) >> [ 40.847841] Calibrating delay using timer specific routine.. 6034.57 >> BogoMIPS (lpj=10053716) >> [ 40.848202] Mount-cache hash table entries: 256 >> [ 40.848437] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 >> bytes/line) >> [ 40.848602] CPU: L2 Cache: 1024K (64 bytes/line) >> [ 40.848766] CPU: Physical Processor ID: 0 >> [ 40.848928] CPU: Processor Core ID: 0 >> [ 40.849103] Freeing SMP alternatives: 26k freed >> [ 40.849613] ACPI: Core revision 20070126 >> [ 40.884963] Using local APIC timer interrupts. >> [ 40.918232] result 12557891 >> [ 40.918393] Detected 12.557 MHz APIC timer. >> [ 40.921062] Booting processor 1/2 APIC 0x1 >> [ 40.931358] Initializing CPU#1 >> [ 41.014213] Calibrating delay using timer specific routine.. 6030.95 >> BogoMIPS (lpj=10046323) >> [ 41.014218] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 >> bytes/line) >> [ 41.014219] CPU: L2 Cache: 1024K (64 bytes/line) >> [ 41.014221] CPU: Physical Processor ID: 0 >> [ 41.014222] CPU: Processor Core ID: 1 >> [ 41.014303] AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ stepping 03 >> [ 41.017460] Brought up 2 CPUs >> [ 41.019044] NET: Registered protocol family 16 >> [ 41.019258] ACPI: bus type pci registered >> [ 41.019428] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved >> [ 41.019592] PCI: Not using MMCONFIG. >> [ 41.019755] PCI: Using configuration type 1 >> [ 41.024096] ACPI: Interpreter enabled >> [ 41.024259] ACPI: Using IOAPIC for interrupt routing >> [ 41.024586] Error attaching device data >> [ 41.024751] Error attaching device data >> [ 41.024916] Error attaching device data >> [ 41.025082] Error attaching device data >> [ 41.031242] ACPI: PCI Root Bridge [PCI0] (0000:00) >> [ 41.031413] PCI: Probing PCI hardware (bus 00) >> [ 41.031942] PCI: Transparent bridge - 0000:00:08.0 >> [ 41.032367] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] >> [ 41.032524] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] >> [ 41.032638] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT] >> [ 41.032705] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT] >> [ 41.032771] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT] >> [ 41.032836] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT] >> [ 41.037361] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *5 >> [ 41.037882] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10 >> [ 41.038385] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *10 >> [ 41.038888] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *11 >> [ 41.039391] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, >> disabled. >> [ 41.039923] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10 >> [ 41.040426] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, >> disabled. >> [ 41.040972] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *10 >> [ 41.041475] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *5 >> [ 41.041978] ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *0, >> disabled. >> [ 41.042510] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7 >> [ 41.043012] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, >> disabled. >> [ 41.043544] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *0, >> disabled. >> [ 41.044088] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11 >> [ 41.044593] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, >> disabled. >> [ 41.045126] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15 >> [ 41.045630] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, >> disabled. >> [ 41.046189] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, >> disabled. >> [ 41.046722] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *0, >> disabled. >> [ 41.047255] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *0, >> disabled. >> [ 41.047708] Linux Plug and Play Support v0.97 (c) Adam Belay >> [ 41.047879] pnp: PnP ACPI init >> [ 41.048045] ACPI: bus type pnp registered >> [ 41.051043] pnp: PnP ACPI: found 13 devices >> [ 41.051205] ACPI: ACPI bus type pnp unregistered >> [ 41.051432] SCSI subsystem initialized >> [ 41.051618] libata version 2.21 loaded. >> [ 41.051654] usbcore: registered new interface driver usbfs >> [ 41.051834] usbcore: registered new interface driver hub >> [ 41.052016] usbcore: registered new device driver usb >> [ 41.052197] PCI: Using ACPI for IRQ routing >> [ 41.052360] PCI: If a device doesn't work, try "pci=routeirq". If it >> helps, post a report >> [ 41.052747] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31 >> [ 41.053027] hpet0: 3 32-bit timers, 25000000 Hz >> [ 41.054255] pnp: 00:05: iomem range 0x0-0x0 could not be reserved >> [ 41.054421] pnp: 00:05: iomem range 0xfee01000-0xfeefffff has been reserved >> [ 41.054589] pnp: 00:07: iomem range 0xfec00000-0xfec00fff could not be >> reserved >> [ 41.054886] pnp: 00:07: iomem range 0xfee00000-0xfee00fff could not be >> reserved >> [ 41.055185] pnp: 00:0a: ioport range 0x290-0x29f has been reserved >> [ 41.055351] pnp: 00:0b: iomem range 0xe0000000-0xefffffff has been reserved >> [ 41.055519] pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved >> [ 41.055685] pnp: 00:0c: iomem range 0xc0000-0xcffff has been reserved >> [ 41.055850] pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved >> [ 41.056017] pnp: 00:0c: iomem range 0x100000-0x7fffffff could not be >> reserved >> [ 41.056338] PCI: Bridge: 0000:00:08.0 >> [ 41.056501] IO window: c000-dfff >> [ 41.056664] MEM window: f9f00000-f9ffffff >> [ 41.056829] PREFETCH window: 88000000-880fffff >> [ 41.056993] PCI: Bridge: 0000:00:0b.0 >> [ 41.057156] IO window: b000-bfff >> [ 41.057319] MEM window: f9e00000-f9efffff >> [ 41.057451] Time: hpet clocksource has been installed. >> [ 41.057645] PREFETCH window: disabled. >> [ 41.057808] PCI: Bridge: 0000:00:0c.0 >> [ 41.057970] IO window: disabled. >> [ 41.058132] MEM window: disabled. >> [ 41.058294] PREFETCH window: disabled. >> [ 41.058457] PCI: Bridge: 0000:00:0d.0 >> [ 41.058619] IO window: e000-efff >> [ 41.058783] MEM window: fa000000-febfffff >> [ 41.058946] PREFETCH window: d0000000-dfffffff >> [ 41.059110] PCI: Bridge: 0000:00:0e.0 >> [ 41.059272] IO window: disabled. >> [ 41.059434] MEM window: disabled. >> [ 41.059596] PREFETCH window: disabled. >> [ 41.059765] PCI: Setting latency timer of device 0000:00:08.0 to 64 >> [ 41.059770] PCI: Setting latency timer of device 0000:00:0b.0 to 64 >> [ 41.059774] PCI: Setting latency timer of device 0000:00:0c.0 to 64 >> [ 41.059778] PCI: Setting latency timer of device 0000:00:0d.0 to 64 >> [ 41.059783] PCI: Setting latency timer of device 0000:00:0e.0 to 64 >> [ 41.059801] NET: Registered protocol family 2 >> [ 41.100619] IP route cache hash table entries: 65536 (order: 7, 524288 >> bytes) >> [ 41.101145] TCP established hash table entries: 131072 (order: 9, 3145728 >> bytes) >> [ 41.102591] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) >> [ 41.103136] TCP: Hash tables configured (established 131072 bind 65536) >> [ 41.103302] TCP reno registered >> [ 41.114592] Total HugeTLB memory allocated, 0 >> [ 41.114825] Loading Reiser4. See www.namesys.com for a description of >> Reiser4. >> [ 41.115182] io scheduler noop registered >> [ 41.115352] io scheduler cfq registered (default) >> [ 41.116320] Boot video device is 0000:04:00.0 >> [ 41.116435] PCI: Setting latency timer of device 0000:00:0b.0 to 64 >> [ 41.116450] assign_interrupt_mode Found MSI capability >> [ 41.116629] Allocate Port Service[0000:00:0b.0:pcie00] >> [ 41.116670] PCI: Setting latency timer of device 0000:00:0c.0 to 64 >> [ 41.116685] assign_interrupt_mode Found MSI capability >> [ 41.116857] Allocate Port Service[0000:00:0c.0:pcie00] >> [ 41.116893] PCI: Setting latency timer of device 0000:00:0d.0 to 64 >> [ 41.116908] assign_interrupt_mode Found MSI capability >> [ 41.117080] Allocate Port Service[0000:00:0d.0:pcie00] >> [ 41.117117] PCI: Setting latency timer of device 0000:00:0e.0 to 64 >> [ 41.117135] assign_interrupt_mode Found MSI capability >> [ 41.120561] Allocate Port Service[0000:00:0e.0:pcie00] >> [ 41.120731] input: Power Button (FF) as /class/input/input0 >> [ 41.120895] ACPI: Power Button (FF) [PWRF] >> [ 41.121116] input: Power Button (CM) as /class/input/input1 >> [ 41.121279] ACPI: Power Button (CM) [PWRB] >> [ 41.140593] Real Time Clock Driver v1.12ac >> [ 41.140939] hpet_resources: 0xfed00000 is busy >> [ 41.140970] Linux agpgart interface v0.102 (c) Dave Jones >> [ 41.141204] tun: Universal TUN/TAP device driver, 1.6 >> [ 41.141367] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> >> [ 41.141551] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 >> [ 41.141716] ide: Assuming 33MHz system bus speed for PIO modes; override >> with idebus=xx >> [ 41.142031] NFORCE-MCP65: IDE controller at PCI slot 0000:00:09.0 >> [ 41.142207] NFORCE-MCP65: chipset revision 161 >> [ 41.142371] NFORCE-MCP65: not 100% native mode: will probe irqs later >> [ 41.142539] NFORCE-MCP65: 0000:00:09.0 (rev a1) UDMA133 controller >> [ 41.142706] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, >> hdb:pio >> [ 41.143065] Probing IDE interface ide0... >> [ 41.430036] hda: SAMSUNG SP1213N, ATA DISK drive >> [ 42.071954] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 >> [ 42.074576] hda: max request size: 512KiB >> [ 42.074789] hda: 234493056 sectors (120060 MB) w/8192KiB Cache, >> CHS=16383/255/63, UDMA(100) >> [ 42.075551] hda: cache flushes supported >> [ 42.075734] hda: hda1 hda2 hda3 < hda5 hda6 hda7 > >> [ 42.116273] ahci 0000:00:0a.0: version 2.2 >> [ 42.116482] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 >> [ 42.116653] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 >> (level, low) -> IRQ 23 >> [ 43.119478] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf >> impl IDE mode >> [ 43.119778] ahci 0000:00:0a.0: flags: 64bit led clo pmp pio >> [ 43.119943] PCI: Setting latency timer of device 0000:00:0a.0 to 64 >> [ 43.120149] scsi0 : ahci >> [ 43.120365] scsi1 : ahci >> [ 43.120556] scsi2 : ahci >> [ 43.120741] scsi3 : ahci >> [ 43.120927] ata1: SATA max UDMA/133 cmd 0xffffc20000014100 ctl >> 0x0000000000000000 bmdma 0x0000000000000000 irq 315 >> [ 43.121227] ata2: SATA max UDMA/133 cmd 0xffffc20000014180 ctl >> 0x0000000000000000 bmdma 0x0000000000000000 irq 315 >> [ 43.121526] ata3: SATA max UDMA/133 cmd 0xffffc20000014200 ctl >> 0x0000000000000000 bmdma 0x0000000000000000 irq 315 >> [ 43.121826] ata4: SATA max UDMA/133 cmd 0xffffc20000014280 ctl >> 0x0000000000000000 bmdma 0x0000000000000000 irq 315 >> [ 43.934296] ata1: softreset failed (1st FIS failed) >> [ 43.934461] ata1: reset failed (errno=-5), retrying in 10 secs >> [ 53.885194] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >> [ 53.885890] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 >> [ 53.886056] ata1.00: 312581808 sectors, multi 16: LBA48 >> [ 53.886804] ata1.00: configured for UDMA/133 >> [ 54.201147] ata2: SATA link down (SStatus 0 SControl 300) >> [ 54.517101] ata3: SATA link down (SStatus 0 SControl 300) >> [ 54.833055] ata4: SATA link down (SStatus 0 SControl 300) >> [ 54.833271] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 >> PQ: 0 ANSI: 5 >> [ 54.833623] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 >> MB) >> [ 54.833793] sd 0:0:0:0: [sda] Write Protect is off >> [ 54.833957] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 >> [ 54.833965] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, >> doesn't support DPO or FUA >> [ 54.834287] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 >> MB) >> [ 54.834455] sd 0:0:0:0: [sda] Write Protect is off >> [ 54.834619] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 >> [ 54.834626] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, >> doesn't support DPO or FUA >> [ 54.834924] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > >> [ 54.869055] sd 0:0:0:0: [sda] Attached SCSI disk >> [ 54.869495] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22 >> [ 54.869667] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 22 >> (level, low) -> IRQ 22 >> [ 54.870288] PCI: Setting latency timer of device 0000:00:02.1 to 64 >> [ 54.870293] ehci_hcd 0000:00:02.1: EHCI Host Controller >> [ 54.870532] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus >> number 1 >> [ 54.870848] ehci_hcd 0000:00:02.1: debug port 1 >> [ 54.871013] PCI: cache line size of 64 is not supported by device >> 0000:00:02.1 >> [ 54.871022] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf9dfec00 >> [ 54.871191] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 >> Dec 2004 >> [ 54.871572] usb usb1: configuration #1 chosen from 1 choice >> [ 54.871761] hub 1-0:1.0: USB hub found >> [ 54.871927] hub 1-0:1.0: 10 ports detected >> [ 54.976112] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) >> Driver >> [ 54.976353] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21 >> [ 54.976523] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 21 >> (level, low) -> IRQ 21 >> [ 54.977020] PCI: Setting latency timer of device 0000:00:02.0 to 64 >> [ 54.977025] ohci_hcd 0000:00:02.0: OHCI Host Controller >> [ 54.977260] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus >> number 2 >> [ 54.977569] ohci_hcd 0000:00:02.0: irq 21, io mem 0xf9dff000 >> [ 55.034680] usb usb2: configuration #1 chosen from 1 choice >> [ 55.034869] hub 2-0:1.0: USB hub found >> [ 55.035037] hub 2-0:1.0: 10 ports detected >> [ 55.139122] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 >> irq 1,12 >> [ 55.142186] serio: i8042 KBD port at 0x60,0x64 irq 1 >> [ 55.142352] serio: i8042 AUX port at 0x60,0x64 irq 12 >> [ 55.142569] mice: PS/2 mouse device common for all mice >> [ 55.169330] input: AT Translated Set 2 keyboard as /class/input/input2 >> [ 55.431622] usb 1-5: new high speed USB device using ehci_hcd and address 3 >> [ 55.566822] usb 1-5: configuration #1 chosen from 1 choice >> [ 55.807525] usb 2-4: new full speed USB device using ohci_hcd and address 2 >> [ 55.963577] usb 2-4: configuration #1 chosen from 1 choice >> [ 55.969539] hub 2-4:1.0: USB hub found >> [ 55.972507] hub 2-4:1.0: 4 ports detected >> [ 56.314740] usb 2-4.1: new full speed USB device using ohci_hcd and address >> 3 >> [ 56.449493] usb 2-4.1: configuration #1 chosen from 1 choice >> [ 56.669944] usb 2-4.3: new low speed USB device using ohci_hcd and address >> 4 >> [ 56.783741] usb 2-4.3: configuration #1 chosen from 1 choice >> [ 56.802767] input: Logitech USB-PS/2 Optical Mouse as /class/input/input3 >> [ 56.802968] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on >> usb-0000:00:02.0-4.3 >> [ 56.803327] usbcore: registered new interface driver usbhid >> [ 56.803492] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver >> [ 56.803690] TCP cubic registered >> [ 56.803861] NET: Registered protocol family 1 >> [ 56.804026] NET: Registered protocol family 17 >> [ 56.804201] powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor >> 6000+ processors (version 2.00.00) >> [ 56.804448] powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x6 >> [ 56.804613] powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0x8 >> [ 56.804778] powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xa >> [ 56.804943] powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xc >> [ 56.805107] powernow-k8: 4 : fid 0xe (2200 MHz), vid 0xe >> [ 56.805272] powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 >> [ 56.805437] powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 >> [ 56.805602] powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 >> [ 56.826551] ReiserFS: sda3: found reiserfs format "3.6" with standard >> journal >> [ 56.826720] ReiserFS: sda3: using ordered data mode >> [ 56.836124] ReiserFS: sda3: journal params: device sda3, size 8192, journal >> first block 18, max trans len 1024, max batch 900, max commit age 30, max >> trans age 30 >> [ 56.837467] ReiserFS: sda3: checking transaction log (sda3) >> [ 56.888740] ReiserFS: sda3: Using r5 hash to sort names >> [ 56.888915] VFS: Mounted root (reiserfs filesystem) readonly. >> [ 56.889092] Freeing unused kernel memory: 184k freed >> [ 61.840593] ReiserFS: sda3: switching to journaled data mode >> [ 62.230945] r8169 Gigabit Ethernet driver 2.2LK loaded >> [ 62.231224] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19 >> [ 62.231232] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19 >> (level, low) -> IRQ 19 >> [ 62.231250] PCI: Setting latency timer of device 0000:01:00.0 to 64 >> [ 62.231430] eth0: RTL8168b/8111b at 0xffffc2000016c000, 00:19:66:47:f3:cb, >> IRQ 19 >> [ 62.284221] HPT366: IDE controller at PCI slot 0000:02:0a.0 >> [ 62.284491] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18 >> [ 62.284499] ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKC] -> GSI 18 >> (level, low) -> IRQ 18 >> [ 62.284508] HPT366: chipset revision 1 >> [ 62.284514] HPT366: using 33 MHz PCI clock >> [ 62.284516] HPT366: 100% native mode on irq 18 >> [ 62.284524] ide1: BM-DMA at 0xd000-0xd007, BIOS settings: hdc:pio, >> hdd:pio >> [ 62.284536] ACPI: PCI Interrupt 0000:02:0a.1[A] -> Link [LNKC] -> GSI 18 >> (level, low) -> IRQ 18 >> [ 62.284544] HPT366: using 33 MHz PCI clock >> [ 62.284546] HPT366: too many IDE interfaces, no room in table >> [ 62.284548] HPT366: neither IDE port enabled (BIOS) >> [ 62.284551] Probing IDE interface ide1... >> [ 62.988343] hdc: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive >> [ 63.630192] ide1 at 0xd480-0xd487,0xd402 on irq 18 >> [ 63.632589] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache >> [ 63.632594] Uniform CD-ROM driver Revision: 3.20 >> [ 64.048482] reiser4: sda5: found disk format 4.0.0. >> [ 69.431516] reiser4: sda6: found disk format 4.0.0. >> [ 70.722395] reiser4: hda7: found disk format 4.0.0. >> [ 71.428725] Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1 >> across:1951888k >> [ 74.227887] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17 >> [ 74.227897] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 17 >> (level, low) -> IRQ 17 >> [ 74.230613] Audigy2 value: Special config. >> [ 78.048887] r8169: eth0: link up >> [ 78.049039] r8169: eth0: link up >> [ 82.597555] nvidia: module license 'NVIDIA' taints kernel. >> [ 82.767839] ACPI: PCI Interrupt Link [LNED] enabled at IRQ 16 >> [ 82.767847] ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNED] -> GSI 16 >> (level, low) -> IRQ 16 >> [ 82.767853] PCI: Setting latency timer of device 0000:04:00.0 to 64 >> [ 82.767943] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.23 Thu >> Oct 4 10:27:34 PDT 2007 >> >> Glück Auf, >> Volker >> > - > To unsubscribe from this list: send the line "unsubscribe linux-ide" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- tejun ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: question about sata-error on boot. 2007-11-07 6:15 ` question about sata-error on boot Andrew Morton 2007-11-12 13:28 ` Tejun Heo @ 2007-12-07 13:32 ` Hemmann, Volker Armin 2007-12-07 23:20 ` Tejun Heo 1 sibling, 1 reply; 4+ messages in thread From: Hemmann, Volker Armin @ 2007-12-07 13:32 UTC (permalink / raw) To: Andrew Morton; +Cc: linux-kernel, linux-ide Hi, On Mittwoch, 7. November 2007, Andrew Morton wrote: > > On Fri, 2 Nov 2007 19:34:20 +0100 "Hemmann, Volker Armin" > > <volker.armin.hemmann@tu-clausthal.de> wrote: Hi, > > (cc linux-ide) > > > for some time (and I can't say for how long, but the board is less than a > > month old) I get this error on boot: > > > > [ 42.116273] ahci 0000:00:0a.0: version 2.2 > > [ 42.116482] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 > > [ 42.116653] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI > > 23 (level, low) -> IRQ 23 > > [ 43.119478] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps > > 0xf impl IDE mode > > [ 43.119778] ahci 0000:00:0a.0: flags: 64bit led clo pmp pio > > [ 43.119943] PCI: Setting latency timer of device 0000:00:0a.0 to 64 > > [ 43.120149] scsi0 : ahci > > [ 43.120365] scsi1 : ahci > > [ 43.120556] scsi2 : ahci > > [ 43.120741] scsi3 : ahci > > [ 43.120927] ata1: SATA max UDMA/133 cmd 0xffffc20000014100 ctl > > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > > [ 43.121227] ata2: SATA max UDMA/133 cmd 0xffffc20000014180 ctl > > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > > [ 43.121526] ata3: SATA max UDMA/133 cmd 0xffffc20000014200 ctl > > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > > [ 43.121826] ata4: SATA max UDMA/133 cmd 0xffffc20000014280 ctl > > 0x0000000000000000 bmdma 0x0000000000000000 irq 315 > > [ 43.934296] ata1: softreset failed (1st FIS failed) > > [ 43.934461] ata1: reset failed (errno=-5), retrying in 10 secs > > [ 53.885194] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > > [ 53.885890] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max > > UDMA/133 [ 53.886056] ata1.00: 312581808 sectors, multi 16: LBA48 > > [ 53.886804] ata1.00: configured for UDMA/133 > > [ 54.201147] ata2: SATA link down (SStatus 0 SControl 300) > > [ 54.517101] ata3: SATA link down (SStatus 0 SControl 300) > > [ 54.833055] ata4: SATA link down (SStatus 0 SControl 300) this is gone with 2.6.22.13 an 2.6.23.9: [ 33.277039] scsi0 : ahci [ 33.277262] scsi1 : ahci [ 33.277454] scsi2 : ahci [ 33.277645] scsi3 : ahci [ 33.277826] ata1: SATA max UDMA/133 cmd 0xffffc20000020100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 315 [ 33.278120] ata2: SATA max UDMA/133 cmd 0xffffc20000020180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 315 [ 33.278414] ata3: SATA max UDMA/133 cmd 0xffffc20000020200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 315 [ 33.278708] ata4: SATA max UDMA/133 cmd 0xffffc20000020280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 315 [ 33.751855] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 33.752659] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 [ 33.752821] ata1.00: 312581808 sectors, multi 16: LBA48 [ 33.753574] ata1.00: configured for UDMA/133 [ 34.067809] ata2: SATA link down (SStatus 0 SControl 300) [ 34.383762] ata3: SATA link down (SStatus 0 SControl 300) [ 34.699717] ata4: SATA link down (SStatus 0 SControl 300) [ 34.700029] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5 [ 34.700377] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 34.700544] sd 0:0:0:0: [sda] Write Protect is off [ 34.700703] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 34.700712] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 34.701026] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 34.701191] sd 0:0:0:0: [sda] Write Protect is off [ 34.701350] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 34.701358] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 34.701651] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: question about sata-error on boot. 2007-12-07 13:32 ` Hemmann, Volker Armin @ 2007-12-07 23:20 ` Tejun Heo 0 siblings, 0 replies; 4+ messages in thread From: Tejun Heo @ 2007-12-07 23:20 UTC (permalink / raw) To: Hemmann, Volker Armin; +Cc: Andrew Morton, linux-kernel, linux-ide Hemmann, Volker Armin wrote: > this is gone with 2.6.22.13 an 2.6.23.9: Thanks for letting us know. Probably CLO related problem which got updated recently. -- tejun ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2007-12-07 23:20 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <200711021934.21123.volker.armin.hemmann@tu-clausthal.de>
2007-11-07 6:15 ` question about sata-error on boot Andrew Morton
2007-11-12 13:28 ` Tejun Heo
2007-12-07 13:32 ` Hemmann, Volker Armin
2007-12-07 23:20 ` Tejun Heo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).