* Re: Sata 4726 Testing
[not found] ` <4769F974.2020905@gmail.com>
@ 2007-12-20 22:23 ` Andrew Ryder
2007-12-22 13:53 ` Andrew Ryder
1 sibling, 0 replies; 26+ messages in thread
From: Andrew Ryder @ 2007-12-20 22:23 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-ide
I've attached the boot log from the 2.6.24-rc5 kernel. The problem
repeats itself in the same manner as with the 2.6.23 kernel with the
libata patches.
Here is the info on the sata controller and HPM.
Addonics:
- 4 port Sata II Raid5 HBA with the SIL3124 (ADSA4R5)
- Mini-Storage tower with HPM (AD5SAHPM-E)
- 2 meter eSata cable
- One IDE-Sata converter for each IDE drive (ADIDESA)
I have 4 seagate 300GB IDE drives installed in the storage tower, each
drive has an ide-sata converter installed on it, and the HPM running in
JBOD mode.
I have upgraded the firmware on the HBA to the latest available from SI
(6.4.09) and the HPM in the storage tower is running the latest version
also (1.2061)
Once the driver has finished attempting to initialize the hardware, the
first hard drive is accessible, the 2nd drive is partially detected, but
unusable. If I try and run fdisk on the 2nd drive, fdisk reports that
"You must set cylinders" before attempting partitioning. The 3rd and 4th
drives are not detected at all.
I have tried the sata controller and HPM under windows 2000, and
everything worked without issue.
I did try previously configuring the HPM in Raid 1 mode to treat the
storage tower as one large disk and this configuration worked without
issue in Linux or windows. Since I returned the unit to JBOD mode, there
have been some additional errors about trying to access beyond the end
of the first drive on the HPM.
If theres any other information you need, please let me know.
Thanks
Here is my system config, software environment and boot logs:
Hardware:
Asus SK8V
Opteron 144
2GB Memory
Adaptec 29160N
1 U160 18GB scsi drive
1 Ultra scsi cd-rom
2 ide drives
2 ide cdroms
Intel Pro/1000 network card
ATI Radeon 9600 AGP
Creative Audigy2 sound card
Here is the output from 'dmesg':
Linux version 2.6.24-rc5 (root@BigMouth) (gcc version 4.1.2 (Gentoo
4.1.2 p1.0.1)) #1 Thu Dec 20 16:29:57 EST 2007
Command line: root=/dev/sda3
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff30000 (usable)
BIOS-e820: 000000007ff30000 - 000000007ff40000 (ACPI data)
BIOS-e820: 000000007ff40000 - 000000007fff0000 (ACPI NVS)
BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 524080) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.3 present.
ACPI: RSDP 000FA850, 0014 (r0 ACPIAM)
ACPI: RSDT 7FF30000, 0030 (r1 A M I OEMRSDT 6000517 MSFT 97)
ACPI: FACP 7FF30200, 0081 (r1 A M I OEMFACP 6000517 MSFT 97)
ACPI: DSDT 7FF303F0, 38EA (r1 SK8V_ SK8V_033 33 MSFT 100000D)
ACPI: FACS 7FF40000, 0040
ACPI: APIC 7FF30390, 0052 (r1 A M I OEMAPIC 6000517 MSFT 97)
ACPI: OEMB 7FF40040, 003F (r1 A M I OEMBIOS 6000517 MSFT 97)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 524080) 1 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 524080
On node 0 totalpages: 523983
DMA zone: 56 pages used for memmap
DMA zone: 964 pages reserved
DMA zone: 2979 pages, LIFO batch:0
DMA32 zone: 7109 pages used for memmap
DMA32 zone: 512875 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ff80000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515854
Kernel command line: root=/dev/sda3
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
time.c: Detected 1802.294 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ f8000000 size 64 MB
Memory: 2059876k/2096320k available (2288k kernel code, 35684k reserved,
1037k data, 192k init)
Calibrating delay using timer specific routine.. 3608.83 BogoMIPS
(lpj=7217678)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Opteron(tm) Processor 144 stepping 0a
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12515939
Detected 12.515 MHz APIC timer.
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: enabled onboard AC97/MC97 devices
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf8000000
Time: tsc clocksource has been installed.
system 00:09: ioport range 0x295-0x296 has been reserved
system 00:09: ioport range 0x3e1-0x3e7 has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x800-0x87f has been reserved
system 00:09: ioport range 0x400-0x41f has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xdffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
system 00:0d: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: fc500000-fcafffff
PREFETCH window: b3e00000-f3dfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1198186556.256:1): initialized
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VIA8237SATA: IDE controller (0x1106:0x3149 rev 0x80) at PCI slot
0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
VIA8237SATA: 100% native mode on irq 20
ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: Maxtor 4G160J8, ATA DISK drive
hda: ST3200822A, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA 5 mode selected
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA 6 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA 2 mode selected
hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
hdd: UDMA 2 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63,
UDMA(100)
hda: cache flushes supported
hda: hda1 hda2
hdb: max request size: 512KiB
hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63,
UDMA(133)
hdb: cache flushes not supported
hdb: hdb1
hdc: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
target0:0:0: Beginning Domain Validation
target0:0:0: wide asynchronous
target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target0:0:0: Ending Domain Validation
scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
target0:0:3: Beginning Domain Validation
target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
target0:0:3: Domain Validation skipping write tests
target0:0:3: Ending Domain Validation
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports
DPO and FUA
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports
DPO and FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
sr 0:0:3:0: Attached scsi CD-ROM sr0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 33
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 0:0:3:0: Attached scsi generic sg1 type 5
libata version 3.00 loaded.
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
input: Power Button (FF) as /class/input/input2
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16]
MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
sata_sil24 0000:00:0c.0: version 1.1
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Disallowing DAC for device 0000:00:0c.0
scsi1 : sata_sil24
scsi2 : sata_sil24
scsi3 : sata_sil24
scsi4 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
input: PC Speaker as /class/input/input5
Floppy drive(s): fd0 is 1.44M
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
FDC 0 is a post-1991 82077
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
ata1: SATA link down (SStatus 0 SControl 0)
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 0)
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
Audigy2 value: Special config.
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 1-1: device not accepting address 2, error -71
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Disallowing DAC for device 0000:00:0e.0
e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
usb 1-1: new low speed USB device using uhci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Das Keyboard as /class/input/input6
input: USB HID v1.11 Keyboard [Das Keyboard] on usb-0000:00:10.0-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Relevant Syslog messages:
Dec 20 16:37:13 BigMouth kernel: ata1: exception Emask 0x10 SAct 0x0
SErr 0x10000 action 0xa frozen
Dec 20 16:37:13 BigMouth kernel: ata1: irq_stat 0x00a40080, device exchanged
Dec 20 16:37:13 BigMouth kernel: ata1: SError: { PHYRdyChg }
Dec 20 16:37:13 BigMouth kernel: ata1: hard resetting link
Dec 20 16:37:16 BigMouth kernel: ata1: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:37:16 BigMouth kernel: ata1.15: Port Multiplier 1.1,
0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
Dec 20 16:37:16 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:37:16 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:37:16 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:37:16 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:37:16 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:37:26 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:37:26 BigMouth apcupsd[5306]: NIS server startup succeeded
Dec 20 16:37:26 BigMouth apcupsd[4755]: apcupsd 3.10.18 (21 July 2005)
gentoo startup succeeded
Dec 20 16:37:26 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:37:26 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:37:36 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:37:36 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:37:36 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:38:11 BigMouth kernel: ata1.01: limiting SATA link speed to
1.5 Gbps
Dec 20 16:38:11 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:38:11 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:38:11 BigMouth kernel: ata1.01: reset failed, giving up
Dec 20 16:38:11 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:38:11 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:38:12 BigMouth gconfd (tireman-5363): starting (version
2.18.0.1), pid 5363 user 'tireman'
Dec 20 16:38:12 BigMouth gconfd (tireman-5363): Resolved address
"xml:readonly:/etc/gconf/gconf.xml.mandatory" to a read-only
configuration source at position 0
Dec 20 16:38:12 BigMouth gconfd (tireman-5363): Resolved address
"xml:readwrite:/home/tireman/.gconf" to a writable configuration source
at position 1
Dec 20 16:38:12 BigMouth gconfd (tireman-5363): Resolved address
"xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-only
configuration source at position 2
Dec 20 16:38:14 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:38:14 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:38:14 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:38:14 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:38:14 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:38:14 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:38:24 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:38:24 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:38:24 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:38:34 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:38:34 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:38:34 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:39:09 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:39:09 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:39:09 BigMouth kernel: ata1.01: reset failed, giving up
Dec 20 16:39:09 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:39:09 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:39:12 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:39:12 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:39:12 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:39:12 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:39:12 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:39:12 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:39:22 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:39:22 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:39:22 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:39:32 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:39:32 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:39:32 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:40:01 BigMouth cron[5381]: (root) CMD (test -x
/usr/sbin/run-crons && /usr/sbin/run-crons )
Dec 20 16:40:07 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:40:07 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:40:07 BigMouth kernel: ata1.01: reset failed, giving up
Dec 20 16:40:07 BigMouth kernel: ata1.01: failed to recover link after 3
tries, disabling
Dec 20 16:40:07 BigMouth kernel: ata1: failed to recover PMP, retrying
in 5 secs
Dec 20 16:40:12 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:40:14 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:40:15 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:40:15 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:40:15 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:40:15 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:40:15 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:40:25 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:40:25 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:40:25 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:40:35 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:40:35 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:40:35 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:41:10 BigMouth kernel: ata1.02: limiting SATA link speed to
1.5 Gbps
Dec 20 16:41:10 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:41:10 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:41:10 BigMouth kernel: ata1.02: reset failed, giving up
Dec 20 16:41:10 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:41:13 BigMouth kernel: ata1.15: softreset failed (SRST command
error)
Dec 20 16:41:13 BigMouth kernel: ata1.15: reset failed (errno=-5),
retrying in 8 secs
Dec 20 16:41:20 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:41:23 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:41:23 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:41:23 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:41:23 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:41:24 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:41:24 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:41:33 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:41:34 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:41:34 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:41:43 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:41:44 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:41:44 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:42:18 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:42:19 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:42:19 BigMouth kernel: ata1.02: reset failed, giving up
Dec 20 16:42:19 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:42:19 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:42:21 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:42:21 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:42:22 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:42:22 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:42:22 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:42:22 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:42:32 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:42:32 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:42:32 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:42:42 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:42:42 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:42:42 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:43:17 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:43:17 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:43:17 BigMouth kernel: ata1.02: reset failed, giving up
Dec 20 16:43:17 BigMouth kernel: ata1.02: failed to recover link after 3
tries, disabling
Dec 20 16:43:17 BigMouth kernel: ata1: failed to recover PMP, retrying
in 5 secs
Dec 20 16:43:22 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:43:24 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:43:25 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:43:25 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:43:25 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:43:26 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:43:26 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:43:35 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:43:35 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:43:35 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:43:45 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:43:46 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:43:46 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:44:20 BigMouth kernel: ata1.03: limiting SATA link speed to
1.5 Gbps
Dec 20 16:44:20 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:44:20 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:44:20 BigMouth kernel: ata1.03: reset failed, giving up
Dec 20 16:44:20 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:44:20 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:44:23 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:44:23 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:44:24 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:44:24 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:44:24 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:44:24 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:44:34 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:44:34 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:44:34 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:44:44 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:44:44 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:44:44 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:45:19 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:45:19 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:45:19 BigMouth kernel: ata1.03: reset failed, giving up
Dec 20 16:45:19 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:45:19 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:45:21 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:45:22 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:45:22 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:45:22 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:45:23 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:45:23 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:45:32 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:45:33 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:45:33 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:45:42 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:45:43 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:45:43 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:46:17 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:46:18 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:46:18 BigMouth kernel: ata1.03: reset failed, giving up
Dec 20 16:46:18 BigMouth kernel: ata1.03: failed to recover link after 3
tries, disabling
Dec 20 16:46:18 BigMouth kernel: ata1: failed to recover PMP, retrying
in 5 secs
Dec 20 16:46:23 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:46:23 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:46:25 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:46:26 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:46:26 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:46:26 BigMouth kernel: ata1.04: hard resetting link
Dec 20 16:46:26 BigMouth kernel: ata1.04: SATA link down (SStatus 0
SControl 320)
Dec 20 16:46:26 BigMouth kernel: ata1.05: hard resetting link
Dec 20 16:46:27 BigMouth kernel: ata1.05: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:46:27 BigMouth kernel: ata1.06: hard resetting link
Dec 20 16:46:27 BigMouth kernel: ata1.06: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:46:27 BigMouth kernel: ata1.00: ATA-7: ST3300831A, 3.03, max
UDMA/100
Dec 20 16:46:27 BigMouth kernel: ata1.00: 586072368 sectors, multi 0: LBA48
Dec 20 16:46:27 BigMouth kernel: ata1.00: applying bridge limits
Dec 20 16:46:27 BigMouth kernel: ata1.00: configured for UDMA/100
Dec 20 16:46:27 BigMouth kernel: ata1.05: ATA-6: Config Disk, PLS12061,
max UDMA/133
Dec 20 16:46:27 BigMouth kernel: ata1.05: 640 sectors, multi 1: LBA
Dec 20 16:46:27 BigMouth kernel: ata1.05: device is on DMA blacklist,
disabling DMA
Dec 20 16:46:27 BigMouth kernel: ata1.05: configured for PIO4
Dec 20 16:46:27 BigMouth kernel: ata1.00: exception Emask 0x10 SAct 0x0
SErr 0x0 action 0x1 t4
Dec 20 16:46:27 BigMouth kernel: ata1.00: irq_stat 0x00020002, failed to
transmit command FIS
Dec 20 16:46:27 BigMouth kernel: ata1.00: configured for UDMA/100
Dec 20 16:46:27 BigMouth kernel: ata1: EH complete
Dec 20 16:46:27 BigMouth kernel: scsi 1:0:0:0: Direct-Access
ATA ST3300831A 3.03 PQ: 0 ANSI: 5
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] 586072368 512-byte
hardware sectors (300069 MB)
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Write Protect is off
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] 586072368 512-byte
hardware sectors (300069 MB)
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Write Protect is off
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Dec 20 16:46:27 BigMouth kernel: sdb: sdb1
Dec 20 16:46:27 BigMouth kernel: sdb: p1 exceeds device capacity
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: Attached scsi generic sg2
type 0
Dec 20 16:46:27 BigMouth kernel: scsi 1:5:0:0: Direct-Access
ATA Config Disk PLS1 PQ: 0 ANSI: 5
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] 640 512-byte hardware
sectors (0 MB)
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Write Protect is off
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Mode Sense: 00 3a 00 00
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Write cache:
disabled, read cache: enabled, doesn't support DPO or FUA
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] 640 512-byte hardware
sectors (0 MB)
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Write Protect is off
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Mode Sense: 00 3a 00 00
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Write cache:
disabled, read cache: enabled, doesn't support DPO or FUA
Dec 20 16:46:27 BigMouth kernel: sdc: unknown partition table
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Attached SCSI disk
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: Attached scsi generic sg3
type 0
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413248, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413184
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413249, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413185
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413250, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413186
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413251, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413187
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413252, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413188
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413253, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413189
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413254, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413190
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413255, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413191
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413248, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413184
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413249, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413185
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413250, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413251, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413252, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413253, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413254, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413255, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413440, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413441, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413442, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413443, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413444, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413445, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413446, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413447, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413440, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413441, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413442, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413443, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413444, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413445, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413446, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413447, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413392, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413393, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413394, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413395, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413396, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413397, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413398, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413399, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413448, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413449, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413450, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413451, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413452, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413453, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413454, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413455, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
BigMouth scripts # ./ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux BigMouth 2.6.24-rc5 #1 Thu Dec 20 16:29:57 EST 2007 x86_64 AMD
Opteron(tm)
Processor 144 AuthenticAMD GNU/Linux
Gnu C 4.1.2
Gnu make 3.81
binutils 2.18
util-linux 2.12r
mount 2.12r
module-init-tools 3.4
e2fsprogs 1.40.3
reiserfsprogs 3.6.19
PPP 2.4.4
Linux C Library 2.6.1
Dynamic linker (ldd) 2.6.1
Procps 3.2.7
Net-tools 1.60
Kbd 1.13
Sh-utils 6.9
udev 115
Modules Loaded smbfs w83627hf hwmon_vid snd_seq_midi
snd_emu10k1_synth s
nd_emux_synth snd_seq_virmidi snd_seq_midi_emul snd_pcm_oss
snd_mixer_oss snd_se
q_oss snd_seq_midi_event snd_seq usbhid e1000 8250_pnp floppy pcspkr
i2c_viapro
i2c_core ehci_hcd thermal snd_emu10k1 snd_rawmidi firmware_class
snd_ac97_codec
ac97_bus snd_pcm uhci_hcd snd_seq_device snd_timer snd_page_alloc
snd_util_mem s
nd_hwdep processor sata_sil24 snd soundcore button ohci1394 usbcore
ieee1394 lib
ata sg
BigMouth scripts # cat /proc/version
Linux version 2.6.24-rc5 (root@BigMouth) (gcc version 4.1.2 (Gentoo
4.1.2 p1.0.1)) #1 Thu Dec 20 16:29:57 EST 2007
BigMouth scripts # cat /proc/modules
smbfs 63952 2 - Live 0xffffffff881ce000
w83627hf 26456 0 - Live 0xffffffff881c6000
hwmon_vid 3200 1 w83627hf, Live 0xffffffff88031000
snd_seq_midi 9344 0 - Live 0xffffffff881c2000
snd_emu10k1_synth 7488 0 - Live 0xffffffff881bf000
snd_emux_synth 34304 1 snd_emu10k1_synth, Live 0xffffffff881b5000
snd_seq_virmidi 7360 1 snd_emux_synth, Live 0xffffffff881b2000
snd_seq_midi_emul 6912 1 snd_emux_synth, Live 0xffffffff881af000
snd_pcm_oss 39712 0 - Live 0xffffffff881a4000
snd_mixer_oss 17280 1 snd_pcm_oss, Live 0xffffffff8819e000
snd_seq_oss 31168 0 - Live 0xffffffff88195000
snd_seq_midi_event 8000 3 snd_seq_midi,snd_seq_virmidi,snd_seq_oss, Live
0xffffffff88157000
snd_seq 50176 8
snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_oss,snd_seq_midi_event,
Live 0xffffffff88187000
usbhid 29408 0 - Live 0xffffffff8817e000
e1000 120704 0 - Live 0xffffffff8815f000
8250_pnp 12352 0 - Live 0xffffffff8815a000
floppy 60360 0 - Live 0xffffffff88147000
pcspkr 3200 0 - Live 0xffffffff88145000
i2c_viapro 9496 0 - Live 0xffffffff88141000
i2c_core 25688 1 i2c_viapro, Live 0xffffffff88139000
ehci_hcd 31692 0 - Live 0xffffffff88130000
thermal 18528 0 - Live 0xffffffff8812a000
snd_emu10k1 137120 1 snd_emu10k1_synth, Live 0xffffffff88105000
snd_rawmidi 25696 3 snd_seq_midi,snd_seq_virmidi,snd_emu10k1, Live
0xffffffff880fd000
firmware_class 10816 1 snd_emu10k1, Live 0xffffffff880f9000
snd_ac97_codec 112536 1 snd_emu10k1, Live 0xffffffff880dc000
ac97_bus 2816 1 snd_ac97_codec, Live 0xffffffff880be000
snd_pcm 75724 3 snd_pcm_oss,snd_emu10k1,snd_ac97_codec, Live
0xffffffff880c8000
uhci_hcd 24728 0 - Live 0xffffffff880c0000
snd_seq_device 8916 7
snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi,
Live 0xffffffff880ba000
snd_timer 23176 3 snd_seq,snd_emu10k1,snd_pcm, Live 0xffffffff880b3000
snd_page_alloc 11152 2 snd_emu10k1,snd_pcm, Live 0xffffffff880af000
snd_util_mem 5504 2 snd_emux_synth,snd_emu10k1, Live 0xffffffff880ac000
snd_hwdep 10696 2 snd_emux_synth,snd_emu10k1, Live 0xffffffff880a8000
processor 30848 1 thermal, Live 0xffffffff8809d000
sata_sil24 17860 0 - Live 0xffffffff88097000
snd 60392 13
snd_emux_synth,snd_seq_virmidi,snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_seq_device,snd_timer,snd_hwdep,
Live 0xffffffff88087000
soundcore 8672 1 snd, Live 0xffffffff88083000
button 9760 0 - Live 0xffffffff8807d000
ohci1394 31860 0 - Live 0xffffffff88074000
usbcore 145296 4 usbhid,ehci_hcd,uhci_hcd, Live 0xffffffff8804d000
ieee1394 94168 1 ohci1394, Live 0xffffffff88033000
libata 154512 1 sata_sil24, Live 0xffffffff8800a000
sg 33080 0 - Live 0xffffffff88000000
BigMouth scripts # cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:0f.1
0170-0177 : ide1
01f0-01f7 : 0000:00:0f.1
01f0-01f7 : ide0
0295-0296 : w83627hf
0295-0296 : pnp 00:09
0295-0296 : w83627hf
02f8-02ff : serial
0376-0376 : 0000:00:0f.1
0376-0376 : ide1
03c0-03df : vga+
03e1-03e7 : pnp 00:09
03f2-03f5 : floppy
03f6-03f6 : 0000:00:0f.1
03f6-03f6 : ide0
03f7-03f7 : floppy DIR
03f8-03ff : serial
0400-041f : pnp 00:09
0400-0407 : vt596_smbus
04d0-04d1 : pnp 00:09
0800-087f : pnp 00:09
0800-0803 : ACPI PM1a_EVT_BLK
0804-0805 : ACPI PM1a_CNT_BLK
0808-080b : ACPI PM_TMR
0820-0823 : ACPI GPE0_BLK
0cf8-0cff : PCI conf1
1000-10ff : 0000:00:11.5
1400-14ff : 0000:00:11.6
5010-5015 : ACPI CPU throttle
a000-afff : PCI Bus #01
a000-a0ff : 0000:01:00.0
b000-b0ff : 0000:00:0d.0
b400-b43f : 0000:00:0e.0
b400-b43f : e1000
b800-b81f : 0000:00:10.0
b800-b81f : uhci_hcd
c000-c01f : 0000:00:10.1
c000-c01f : uhci_hcd
c400-c41f : 0000:00:10.2
c400-c41f : uhci_hcd
c800-c81f : 0000:00:10.3
c800-c81f : uhci_hcd
cc00-cc7f : 0000:00:07.0
d000-d0ff : 0000:00:0f.0
d400-d40f : 0000:00:0f.0
d400-d407 : ide2
d408-d40f : ide3
d800-d803 : 0000:00:0f.0
dc00-dc3f : 0000:00:09.0
dc00-dc3f : EMU10K1
e000-e007 : 0000:00:0f.0
e400-e403 : 0000:00:0f.0
e800-e807 : 0000:00:0f.0
ec00-ec0f : 0000:00:0c.0
fc00-fc0f : 0000:00:0f.1
fc00-fc07 : ide0
fc08-fc0f : ide1
BigMouth scripts # cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000c0000-000dffff : pnp 00:0d
000e4000-000fffff : reserved
00100000-7ff2ffff : System RAM
00200000-0043c26b : Kernel code
0043c26c-0053f94f : Kernel data
00579000-005bc997 : Kernel bss
7ff30000-7ff3ffff : ACPI Tables
7ff40000-7ffeffff : ACPI Non-volatile Storage
7fff0000-7fffffff : reserved
b3e00000-f3dfffff : PCI Bus #01
d0000000-dfffffff : 0000:01:00.1
e0000000-efffffff : 0000:01:00.0
f8000000-fbffffff : GART
f8000000-fbffffff : aperture
fc500000-fcafffff : PCI Bus #01
fc800000-fc80ffff : 0000:01:00.1
fc900000-fc91ffff : 0000:01:00.0
fca00000-fca0ffff : 0000:01:00.0
fd400000-fd4007ff : 0000:00:07.0
fd400000-fd4007ff : ohci1394
fd700000-fd77ffff : 0000:00:0c.0
fd800000-fd807fff : 0000:00:0c.0
fd800000-fd807fff : sata_sil24
fd900000-fd90007f : 0000:00:0c.0
fd900000-fd90007f : sata_sil24
fda00000-fda1ffff : 0000:00:0d.0
fdb00000-fdb00fff : 0000:00:0d.0
fdb00000-fdb00fff : aic7xxx
fdc00000-fdc1ffff : 0000:00:0e.0
fdd00000-fdd1ffff : 0000:00:0e.0
fdd00000-fdd1ffff : e1000
fde00000-fde1ffff : 0000:00:0e.0
fde00000-fde1ffff : e1000
fdf00000-fdf000ff : 0000:00:10.4
fdf00000-fdf000ff : ehci_hcd
fec00000-fec00fff : IOAPIC 0
fec00000-fec00fff : pnp 00:0a
fee00000-fee00fff : Local APIC
fff80000-ffffffff : reserved
BigMouth scripts # lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host
Bridge (rev 01)
Subsystem: ASUSTeK Computer Inc. K8V Deluxe/K8V-X motherboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at <ignored> (32-bit, prefetchable)
Capabilities: [80] AGP version 3.5
Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 1.02
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge
[K8T800/K8T890 South] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fc500000-fcafffff
Prefetchable memory behind bridge: b3e00000-f3dfffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A8V Deluxe
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fd400000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at cc00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Multimedia audio controller: Creative Labs SB0400 Audigy2 Value
Subsystem: Creative Labs Unknown device 1001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at dc00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 RAID bus controller: Silicon Image, Inc. SiI 3124 PCI-X Serial
ATA Controller (rev 02)
Subsystem: Silicon Image, Inc. Unknown device 7124
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr-
Stepping+ SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fd900000 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at fd800000 (64-bit, non-prefetchable) [size=32K]
Region 4: I/O ports at ec00 [size=16]
Expansion ROM at fd700000 [disabled] [size=512K]
Capabilities: [64] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=12
Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=2048 DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz-
Capabilities: [54] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:0d.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
Subsystem: Adaptec 29160N Ultra160 SCSI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
BIST result: 00
Region 0: I/O ports at b000 [disabled] [size=256]
Region 1: Memory at fdb00000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at fda00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 Ethernet controller: Intel Corporation 82541GI/PI Gigabit
Ethernet Controller
Subsystem: Intel Corporation PRO/1000 MT Desktop Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fde00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fdd00000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at b400 [size=64]
Expansion ROM at fdc00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple
DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID
Controller (rev 80)
Subsystem: ASUSTeK Computer Inc. A7V600/K8V Deluxe/K8V-X/A8V Deluxe
motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at e800 [size=8]
Region 1: I/O ports at e400 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at d800 [size=4]
Region 4: I/O ports at d400 [size=16]
Region 5: I/O ports at d000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 20
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at c000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at c400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if
20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 21
Region 0: Memory at fdf00000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
[KT600/K8T800/K8T890 South]
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
Subsystem: ASUSTeK Computer Inc. Unknown device 80f3
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 0
Region 0: I/O ports at 1000 [disabled] [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem
Controller (rev 80)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 0
Region 0: I/O ports at 1400 [disabled] [size=256]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 AQ [Radeon
9600] (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. A9600SE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at a000 [size=256]
Region 2: Memory at fca00000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fc900000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.1 Display controller: ATI Technologies Inc RV350 AQ [Radeon 9600]
(Secondary)
Subsystem: ASUSTeK Computer Inc. A9600SE (Secondary)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: Memory at fc800000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
BigMouth scripts # cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: SEAGATE Model: ST318452LW Rev: 0004
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: YAMAHA Model: CRW8824S Rev: 1.00
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: ST3300831A Rev: 3.03
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 05 Id: 00 Lun: 00
Vendor: ATA Model: Config Disk Rev: PLS1
Type: Direct-Access ANSI SCSI revision: 05
Tejun Heo wrote:
> Andrew Ryder wrote:
>
>> Hello,
>>
>> Are you still looking an extra person to test your driver for the
>> SiliconImage 4726?
>>
>> I have a Sil3124 raid controller and a mini-storage tower with the
>> sil4726 hardware Port-Multiplier, both from Addonics.
>>
>> So far I havn't been able to get my hardware combination to work, I have
>> applied your latest patch to the 2.6.23 kernel and only the first drive
>> on the HPM (I have 4 300gb drives installed) is detected and usable. The
>> 2nd drive is partially detected, but does not work.
>>
>
> I have reports of detection failure but yours sounds like PMP support is
> not there at all. Please
>
> * cc linux-ide@vger.kernel.org
>
> * try 2.6.24-rc5 and post the kernel boot log
>
>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
[not found] ` <4769F974.2020905@gmail.com>
2007-12-20 22:23 ` Sata 4726 Testing Andrew Ryder
@ 2007-12-22 13:53 ` Andrew Ryder
2008-01-07 16:12 ` Tejun Heo
1 sibling, 1 reply; 26+ messages in thread
From: Andrew Ryder @ 2007-12-22 13:53 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-ide
I've attached the boot log from the 2.6.24-rc5 kernel. The problem
repeats itself in the same manner as with the 2.6.23 kernel with the
libata patches.
Here is the info on the sata controller and HPM.
Addonics:
- 4 port Sata II Raid5 HBA with the SIL3124 (ADSA4R5)
- Mini-Storage tower with HPM (AD5SAHPM-E)
- 2 meter eSata cable
- One IDE-Sata converter for each IDE drive (ADIDESA)
I have 4 seagate 300GB IDE drives installed in the storage tower, each
drive has an ide-sata converter installed on it, and the HPM running in
JBOD mode.
I have upgraded the firmware on the HBA to the latest available from SI
(6.4.09) and the HPM in the storage tower is running the latest version
also (1.2061)
Once the driver has finished attempting to initialize the hardware, the
first hard drive is accessible, the 2nd drive is partially detected, but
unusable. If I try and run fdisk on the 2nd drive, fdisk reports that
"You must set cylinders" before attempting partitioning. The 3rd and 4th
drives are not detected at all.
I have tried the sata controller and HPM under windows 2000, and
everything worked without issue.
I did try previously configuring the HPM in Raid 1 mode to treat the
storage tower as one large disk and this configuration worked without
issue in Linux or windows. Since I returned the unit to JBOD mode, there
have been some additional errors about trying to access beyond the end
of the first drive on the HPM.
If theres any other information you need, please let me know.
Thanks
Here is my system config, software environment and boot logs:
Hardware:
Asus SK8V
Opteron 144
2GB Memory
Adaptec 29160N
1 U160 18GB scsi drive
1 Ultra scsi cd-rom
2 ide drives
2 ide cdroms
Intel Pro/1000 network card
ATI Radeon 9600 AGP
Creative Audigy2 sound card
Here is the output from 'dmesg':
Linux version 2.6.24-rc5 (root@BigMouth) (gcc version 4.1.2 (Gentoo
4.1.2 p1.0.1)) #1 Thu Dec 20 16:29:57 EST 2007
Command line: root=/dev/sda3
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff30000 (usable)
BIOS-e820: 000000007ff30000 - 000000007ff40000 (ACPI data)
BIOS-e820: 000000007ff40000 - 000000007fff0000 (ACPI NVS)
BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 524080) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.3 present.
ACPI: RSDP 000FA850, 0014 (r0 ACPIAM)
ACPI: RSDT 7FF30000, 0030 (r1 A M I OEMRSDT 6000517 MSFT 97)
ACPI: FACP 7FF30200, 0081 (r1 A M I OEMFACP 6000517 MSFT 97)
ACPI: DSDT 7FF303F0, 38EA (r1 SK8V_ SK8V_033 33 MSFT 100000D)
ACPI: FACS 7FF40000, 0040
ACPI: APIC 7FF30390, 0052 (r1 A M I OEMAPIC 6000517 MSFT 97)
ACPI: OEMB 7FF40040, 003F (r1 A M I OEMBIOS 6000517 MSFT 97)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 524080) 1 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 524080
On node 0 totalpages: 523983
DMA zone: 56 pages used for memmap
DMA zone: 964 pages reserved
DMA zone: 2979 pages, LIFO batch:0
DMA32 zone: 7109 pages used for memmap
DMA32 zone: 512875 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ff80000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515854
Kernel command line: root=/dev/sda3
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
time.c: Detected 1802.294 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ f8000000 size 64 MB
Memory: 2059876k/2096320k available (2288k kernel code, 35684k reserved,
1037k data, 192k init)
Calibrating delay using timer specific routine.. 3608.83 BogoMIPS
(lpj=7217678)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Opteron(tm) Processor 144 stepping 0a
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12515939
Detected 12.515 MHz APIC timer.
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: enabled onboard AC97/MC97 devices
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf8000000
Time: tsc clocksource has been installed.
system 00:09: ioport range 0x295-0x296 has been reserved
system 00:09: ioport range 0x3e1-0x3e7 has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x800-0x87f has been reserved
system 00:09: ioport range 0x400-0x41f has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xdffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
system 00:0d: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: fc500000-fcafffff
PREFETCH window: b3e00000-f3dfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1198186556.256:1): initialized
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VIA8237SATA: IDE controller (0x1106:0x3149 rev 0x80) at PCI slot
0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
VIA8237SATA: 100% native mode on irq 20
ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: Maxtor 4G160J8, ATA DISK drive
hda: ST3200822A, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA 5 mode selected
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA 6 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA 2 mode selected
hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
hdd: UDMA 2 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63,
UDMA(100)
hda: cache flushes supported
hda: hda1 hda2
hdb: max request size: 512KiB
hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63,
UDMA(133)
hdb: cache flushes not supported
hdb: hdb1
hdc: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
target0:0:0: Beginning Domain Validation
target0:0:0: wide asynchronous
target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target0:0:0: Ending Domain Validation
scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
target0:0:3: Beginning Domain Validation
target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
target0:0:3: Domain Validation skipping write tests
target0:0:3: Ending Domain Validation
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports
DPO and FUA
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports
DPO and FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
sr 0:0:3:0: Attached scsi CD-ROM sr0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 33
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 0:0:3:0: Attached scsi generic sg1 type 5
libata version 3.00 loaded.
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
input: Power Button (FF) as /class/input/input2
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16]
MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
sata_sil24 0000:00:0c.0: version 1.1
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Disallowing DAC for device 0000:00:0c.0
scsi1 : sata_sil24
scsi2 : sata_sil24
scsi3 : sata_sil24
scsi4 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
input: PC Speaker as /class/input/input5
Floppy drive(s): fd0 is 1.44M
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
FDC 0 is a post-1991 82077
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
ata1: SATA link down (SStatus 0 SControl 0)
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 0)
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
Audigy2 value: Special config.
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 1-1: device not accepting address 2, error -71
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Disallowing DAC for device 0000:00:0e.0
e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
usb 1-1: new low speed USB device using uhci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Das Keyboard as /class/input/input6
input: USB HID v1.11 Keyboard [Das Keyboard] on usb-0000:00:10.0-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Relevant Syslog messages:
Dec 20 16:37:13 BigMouth kernel: ata1: exception Emask 0x10 SAct 0x0
SErr 0x10000 action 0xa frozen
Dec 20 16:37:13 BigMouth kernel: ata1: irq_stat 0x00a40080, device exchanged
Dec 20 16:37:13 BigMouth kernel: ata1: SError: { PHYRdyChg }
Dec 20 16:37:13 BigMouth kernel: ata1: hard resetting link
Dec 20 16:37:16 BigMouth kernel: ata1: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:37:16 BigMouth kernel: ata1.15: Port Multiplier 1.1,
0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
Dec 20 16:37:16 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:37:16 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:37:16 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:37:16 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:37:16 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:37:26 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:37:26 BigMouth apcupsd[5306]: NIS server startup succeeded
Dec 20 16:37:26 BigMouth apcupsd[4755]: apcupsd 3.10.18 (21 July 2005)
gentoo startup succeeded
Dec 20 16:37:26 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:37:26 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:37:36 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:37:36 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:37:36 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:38:11 BigMouth kernel: ata1.01: limiting SATA link speed to
1.5 Gbps
Dec 20 16:38:11 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:38:11 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:38:11 BigMouth kernel: ata1.01: reset failed, giving up
Dec 20 16:38:11 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:38:11 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:38:12 BigMouth gconfd (tireman-5363): starting (version
2.18.0.1), pid 5363 user 'tireman'
Dec 20 16:38:12 BigMouth gconfd (tireman-5363): Resolved address
"xml:readonly:/etc/gconf/gconf.xml.mandatory" to a read-only
configuration source at position 0
Dec 20 16:38:12 BigMouth gconfd (tireman-5363): Resolved address
"xml:readwrite:/home/tireman/.gconf" to a writable configuration source
at position 1
Dec 20 16:38:12 BigMouth gconfd (tireman-5363): Resolved address
"xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-only
configuration source at position 2
Dec 20 16:38:14 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:38:14 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:38:14 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:38:14 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:38:14 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:38:14 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:38:24 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:38:24 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:38:24 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:38:34 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:38:34 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:38:34 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:39:09 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:39:09 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:39:09 BigMouth kernel: ata1.01: reset failed, giving up
Dec 20 16:39:09 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:39:09 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:39:12 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:39:12 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:39:12 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:39:12 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:39:12 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:39:12 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:39:22 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:39:22 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:39:22 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:39:32 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:39:32 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:39:32 BigMouth kernel: ata1.01: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:40:01 BigMouth cron[5381]: (root) CMD (test -x
/usr/sbin/run-crons && /usr/sbin/run-crons )
Dec 20 16:40:07 BigMouth kernel: ata1.01: hard resetting link
Dec 20 16:40:07 BigMouth kernel: ata1.01: softreset failed (SRST command
error)
Dec 20 16:40:07 BigMouth kernel: ata1.01: reset failed, giving up
Dec 20 16:40:07 BigMouth kernel: ata1.01: failed to recover link after 3
tries, disabling
Dec 20 16:40:07 BigMouth kernel: ata1: failed to recover PMP, retrying
in 5 secs
Dec 20 16:40:12 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:40:14 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:40:15 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:40:15 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:40:15 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:40:15 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:40:15 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:40:25 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:40:25 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:40:25 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:40:35 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:40:35 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:40:35 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:41:10 BigMouth kernel: ata1.02: limiting SATA link speed to
1.5 Gbps
Dec 20 16:41:10 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:41:10 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:41:10 BigMouth kernel: ata1.02: reset failed, giving up
Dec 20 16:41:10 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:41:13 BigMouth kernel: ata1.15: softreset failed (SRST command
error)
Dec 20 16:41:13 BigMouth kernel: ata1.15: reset failed (errno=-5),
retrying in 8 secs
Dec 20 16:41:20 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:41:23 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:41:23 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:41:23 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:41:23 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:41:24 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:41:24 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:41:33 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:41:34 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:41:34 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:41:43 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:41:44 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:41:44 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:42:18 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:42:19 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:42:19 BigMouth kernel: ata1.02: reset failed, giving up
Dec 20 16:42:19 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:42:19 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:42:21 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:42:21 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:42:22 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:42:22 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:42:22 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:42:22 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:42:32 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:42:32 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:42:32 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:42:42 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:42:42 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:42:42 BigMouth kernel: ata1.02: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:43:17 BigMouth kernel: ata1.02: hard resetting link
Dec 20 16:43:17 BigMouth kernel: ata1.02: softreset failed (SRST command
error)
Dec 20 16:43:17 BigMouth kernel: ata1.02: reset failed, giving up
Dec 20 16:43:17 BigMouth kernel: ata1.02: failed to recover link after 3
tries, disabling
Dec 20 16:43:17 BigMouth kernel: ata1: failed to recover PMP, retrying
in 5 secs
Dec 20 16:43:22 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:43:24 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:43:25 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:43:25 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:43:25 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:43:26 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:43:26 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:43:35 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:43:35 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:43:35 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:43:45 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:43:46 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:43:46 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:44:20 BigMouth kernel: ata1.03: limiting SATA link speed to
1.5 Gbps
Dec 20 16:44:20 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:44:20 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:44:20 BigMouth kernel: ata1.03: reset failed, giving up
Dec 20 16:44:20 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:44:20 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:44:23 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:44:23 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:44:24 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:44:24 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:44:24 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:44:24 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:44:34 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:44:34 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:44:34 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:44:44 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:44:44 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:44:44 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:45:19 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:45:19 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:45:19 BigMouth kernel: ata1.03: reset failed, giving up
Dec 20 16:45:19 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:45:19 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:45:21 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:45:22 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:45:22 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:45:22 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:45:23 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:45:23 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:45:32 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:45:33 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:45:33 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 10 secs
Dec 20 16:45:42 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:45:43 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:45:43 BigMouth kernel: ata1.03: reset failed (errno=-5),
retrying in 35 secs
Dec 20 16:46:17 BigMouth kernel: ata1.03: hard resetting link
Dec 20 16:46:18 BigMouth kernel: ata1.03: softreset failed (SRST command
error)
Dec 20 16:46:18 BigMouth kernel: ata1.03: reset failed, giving up
Dec 20 16:46:18 BigMouth kernel: ata1.03: failed to recover link after 3
tries, disabling
Dec 20 16:46:18 BigMouth kernel: ata1: failed to recover PMP, retrying
in 5 secs
Dec 20 16:46:23 BigMouth kernel: ata1.15: hard resetting link
Dec 20 16:46:23 BigMouth kernel: ata1: controller in dubious state,
performing PORT_RST
Dec 20 16:46:25 BigMouth kernel: ata1.15: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:46:26 BigMouth kernel: ata1.00: hard resetting link
Dec 20 16:46:26 BigMouth kernel: ata1.00: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:46:26 BigMouth kernel: ata1.04: hard resetting link
Dec 20 16:46:26 BigMouth kernel: ata1.04: SATA link down (SStatus 0
SControl 320)
Dec 20 16:46:26 BigMouth kernel: ata1.05: hard resetting link
Dec 20 16:46:27 BigMouth kernel: ata1.05: SATA link up 3.0 Gbps (SStatus
123 SControl 0)
Dec 20 16:46:27 BigMouth kernel: ata1.06: hard resetting link
Dec 20 16:46:27 BigMouth kernel: ata1.06: SATA link up 1.5 Gbps (SStatus
113 SControl 320)
Dec 20 16:46:27 BigMouth kernel: ata1.00: ATA-7: ST3300831A, 3.03, max
UDMA/100
Dec 20 16:46:27 BigMouth kernel: ata1.00: 586072368 sectors, multi 0: LBA48
Dec 20 16:46:27 BigMouth kernel: ata1.00: applying bridge limits
Dec 20 16:46:27 BigMouth kernel: ata1.00: configured for UDMA/100
Dec 20 16:46:27 BigMouth kernel: ata1.05: ATA-6: Config Disk, PLS12061,
max UDMA/133
Dec 20 16:46:27 BigMouth kernel: ata1.05: 640 sectors, multi 1: LBA
Dec 20 16:46:27 BigMouth kernel: ata1.05: device is on DMA blacklist,
disabling DMA
Dec 20 16:46:27 BigMouth kernel: ata1.05: configured for PIO4
Dec 20 16:46:27 BigMouth kernel: ata1.00: exception Emask 0x10 SAct 0x0
SErr 0x0 action 0x1 t4
Dec 20 16:46:27 BigMouth kernel: ata1.00: irq_stat 0x00020002, failed to
transmit command FIS
Dec 20 16:46:27 BigMouth kernel: ata1.00: configured for UDMA/100
Dec 20 16:46:27 BigMouth kernel: ata1: EH complete
Dec 20 16:46:27 BigMouth kernel: scsi 1:0:0:0: Direct-Access
ATA ST3300831A 3.03 PQ: 0 ANSI: 5
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] 586072368 512-byte
hardware sectors (300069 MB)
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Write Protect is off
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] 586072368 512-byte
hardware sectors (300069 MB)
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Write Protect is off
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Dec 20 16:46:27 BigMouth kernel: sdb: sdb1
Dec 20 16:46:27 BigMouth kernel: sdb: p1 exceeds device capacity
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
Dec 20 16:46:27 BigMouth kernel: sd 1:0:0:0: Attached scsi generic sg2
type 0
Dec 20 16:46:27 BigMouth kernel: scsi 1:5:0:0: Direct-Access
ATA Config Disk PLS1 PQ: 0 ANSI: 5
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] 640 512-byte hardware
sectors (0 MB)
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Write Protect is off
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Mode Sense: 00 3a 00 00
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Write cache:
disabled, read cache: enabled, doesn't support DPO or FUA
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] 640 512-byte hardware
sectors (0 MB)
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Write Protect is off
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Mode Sense: 00 3a 00 00
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Write cache:
disabled, read cache: enabled, doesn't support DPO or FUA
Dec 20 16:46:27 BigMouth kernel: sdc: unknown partition table
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: [sdc] Attached SCSI disk
Dec 20 16:46:27 BigMouth kernel: sd 1:5:0:0: Attached scsi generic sg3
type 0
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413248, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413184
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413249, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413185
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413250, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413186
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413251, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413187
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413252, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413188
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413253, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413189
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413254, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413190
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413255, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413191
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413248, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413184
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413249, limit=586072368
Dec 20 16:46:27 BigMouth kernel: Buffer I/O error on device sdb1,
logical block 2340413185
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413250, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413251, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413252, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413253, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413254, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413255, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413440, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413441, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413442, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413443, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413444, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413445, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413446, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413447, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413440, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413441, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413442, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413443, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413444, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413445, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413446, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413447, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413392, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413393, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413394, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413395, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413396, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413397, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413398, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413399, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413448, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413449, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413450, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413451, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413452, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413453, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413454, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413455, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413456, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413457, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413458, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413459, limit=586072368
Dec 20 16:46:27 BigMouth kernel: attempt to access beyond end of device
Dec 20 16:46:27 BigMouth kernel: sdb: rw=0, want=2340413460, limit=586072368
BigMouth scripts # ./ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux BigMouth 2.6.24-rc5 #1 Thu Dec 20 16:29:57 EST 2007 x86_64 AMD
Opteron(tm)
Processor 144 AuthenticAMD GNU/Linux
Gnu C 4.1.2
Gnu make 3.81
binutils 2.18
util-linux 2.12r
mount 2.12r
module-init-tools 3.4
e2fsprogs 1.40.3
reiserfsprogs 3.6.19
PPP 2.4.4
Linux C Library 2.6.1
Dynamic linker (ldd) 2.6.1
Procps 3.2.7
Net-tools 1.60
Kbd 1.13
Sh-utils 6.9
udev 115
Modules Loaded smbfs w83627hf hwmon_vid snd_seq_midi
snd_emu10k1_synth s
nd_emux_synth snd_seq_virmidi snd_seq_midi_emul snd_pcm_oss
snd_mixer_oss snd_se
q_oss snd_seq_midi_event snd_seq usbhid e1000 8250_pnp floppy pcspkr
i2c_viapro
i2c_core ehci_hcd thermal snd_emu10k1 snd_rawmidi firmware_class
snd_ac97_codec
ac97_bus snd_pcm uhci_hcd snd_seq_device snd_timer snd_page_alloc
snd_util_mem s
nd_hwdep processor sata_sil24 snd soundcore button ohci1394 usbcore
ieee1394 lib
ata sg
BigMouth scripts # cat /proc/version
Linux version 2.6.24-rc5 (root@BigMouth) (gcc version 4.1.2 (Gentoo
4.1.2 p1.0.1)) #1 Thu Dec 20 16:29:57 EST 2007
BigMouth scripts # cat /proc/modules
smbfs 63952 2 - Live 0xffffffff881ce000
w83627hf 26456 0 - Live 0xffffffff881c6000
hwmon_vid 3200 1 w83627hf, Live 0xffffffff88031000
snd_seq_midi 9344 0 - Live 0xffffffff881c2000
snd_emu10k1_synth 7488 0 - Live 0xffffffff881bf000
snd_emux_synth 34304 1 snd_emu10k1_synth, Live 0xffffffff881b5000
snd_seq_virmidi 7360 1 snd_emux_synth, Live 0xffffffff881b2000
snd_seq_midi_emul 6912 1 snd_emux_synth, Live 0xffffffff881af000
snd_pcm_oss 39712 0 - Live 0xffffffff881a4000
snd_mixer_oss 17280 1 snd_pcm_oss, Live 0xffffffff8819e000
snd_seq_oss 31168 0 - Live 0xffffffff88195000
snd_seq_midi_event 8000 3 snd_seq_midi,snd_seq_virmidi,snd_seq_oss, Live
0xffffffff88157000
snd_seq 50176 8
snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_oss,snd_seq_midi_event,
Live 0xffffffff88187000
usbhid 29408 0 - Live 0xffffffff8817e000
e1000 120704 0 - Live 0xffffffff8815f000
8250_pnp 12352 0 - Live 0xffffffff8815a000
floppy 60360 0 - Live 0xffffffff88147000
pcspkr 3200 0 - Live 0xffffffff88145000
i2c_viapro 9496 0 - Live 0xffffffff88141000
i2c_core 25688 1 i2c_viapro, Live 0xffffffff88139000
ehci_hcd 31692 0 - Live 0xffffffff88130000
thermal 18528 0 - Live 0xffffffff8812a000
snd_emu10k1 137120 1 snd_emu10k1_synth, Live 0xffffffff88105000
snd_rawmidi 25696 3 snd_seq_midi,snd_seq_virmidi,snd_emu10k1, Live
0xffffffff880fd000
firmware_class 10816 1 snd_emu10k1, Live 0xffffffff880f9000
snd_ac97_codec 112536 1 snd_emu10k1, Live 0xffffffff880dc000
ac97_bus 2816 1 snd_ac97_codec, Live 0xffffffff880be000
snd_pcm 75724 3 snd_pcm_oss,snd_emu10k1,snd_ac97_codec, Live
0xffffffff880c8000
uhci_hcd 24728 0 - Live 0xffffffff880c0000
snd_seq_device 8916 7
snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi,
Live 0xffffffff880ba000
snd_timer 23176 3 snd_seq,snd_emu10k1,snd_pcm, Live 0xffffffff880b3000
snd_page_alloc 11152 2 snd_emu10k1,snd_pcm, Live 0xffffffff880af000
snd_util_mem 5504 2 snd_emux_synth,snd_emu10k1, Live 0xffffffff880ac000
snd_hwdep 10696 2 snd_emux_synth,snd_emu10k1, Live 0xffffffff880a8000
processor 30848 1 thermal, Live 0xffffffff8809d000
sata_sil24 17860 0 - Live 0xffffffff88097000
snd 60392 13
snd_emux_synth,snd_seq_virmidi,snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_seq_device,snd_timer,snd_hwdep,
Live 0xffffffff88087000
soundcore 8672 1 snd, Live 0xffffffff88083000
button 9760 0 - Live 0xffffffff8807d000
ohci1394 31860 0 - Live 0xffffffff88074000
usbcore 145296 4 usbhid,ehci_hcd,uhci_hcd, Live 0xffffffff8804d000
ieee1394 94168 1 ohci1394, Live 0xffffffff88033000
libata 154512 1 sata_sil24, Live 0xffffffff8800a000
sg 33080 0 - Live 0xffffffff88000000
BigMouth scripts # cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:0f.1
0170-0177 : ide1
01f0-01f7 : 0000:00:0f.1
01f0-01f7 : ide0
0295-0296 : w83627hf
0295-0296 : pnp 00:09
0295-0296 : w83627hf
02f8-02ff : serial
0376-0376 : 0000:00:0f.1
0376-0376 : ide1
03c0-03df : vga+
03e1-03e7 : pnp 00:09
03f2-03f5 : floppy
03f6-03f6 : 0000:00:0f.1
03f6-03f6 : ide0
03f7-03f7 : floppy DIR
03f8-03ff : serial
0400-041f : pnp 00:09
0400-0407 : vt596_smbus
04d0-04d1 : pnp 00:09
0800-087f : pnp 00:09
0800-0803 : ACPI PM1a_EVT_BLK
0804-0805 : ACPI PM1a_CNT_BLK
0808-080b : ACPI PM_TMR
0820-0823 : ACPI GPE0_BLK
0cf8-0cff : PCI conf1
1000-10ff : 0000:00:11.5
1400-14ff : 0000:00:11.6
5010-5015 : ACPI CPU throttle
a000-afff : PCI Bus #01
a000-a0ff : 0000:01:00.0
b000-b0ff : 0000:00:0d.0
b400-b43f : 0000:00:0e.0
b400-b43f : e1000
b800-b81f : 0000:00:10.0
b800-b81f : uhci_hcd
c000-c01f : 0000:00:10.1
c000-c01f : uhci_hcd
c400-c41f : 0000:00:10.2
c400-c41f : uhci_hcd
c800-c81f : 0000:00:10.3
c800-c81f : uhci_hcd
cc00-cc7f : 0000:00:07.0
d000-d0ff : 0000:00:0f.0
d400-d40f : 0000:00:0f.0
d400-d407 : ide2
d408-d40f : ide3
d800-d803 : 0000:00:0f.0
dc00-dc3f : 0000:00:09.0
dc00-dc3f : EMU10K1
e000-e007 : 0000:00:0f.0
e400-e403 : 0000:00:0f.0
e800-e807 : 0000:00:0f.0
ec00-ec0f : 0000:00:0c.0
fc00-fc0f : 0000:00:0f.1
fc00-fc07 : ide0
fc08-fc0f : ide1
BigMouth scripts # cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000c0000-000dffff : pnp 00:0d
000e4000-000fffff : reserved
00100000-7ff2ffff : System RAM
00200000-0043c26b : Kernel code
0043c26c-0053f94f : Kernel data
00579000-005bc997 : Kernel bss
7ff30000-7ff3ffff : ACPI Tables
7ff40000-7ffeffff : ACPI Non-volatile Storage
7fff0000-7fffffff : reserved
b3e00000-f3dfffff : PCI Bus #01
d0000000-dfffffff : 0000:01:00.1
e0000000-efffffff : 0000:01:00.0
f8000000-fbffffff : GART
f8000000-fbffffff : aperture
fc500000-fcafffff : PCI Bus #01
fc800000-fc80ffff : 0000:01:00.1
fc900000-fc91ffff : 0000:01:00.0
fca00000-fca0ffff : 0000:01:00.0
fd400000-fd4007ff : 0000:00:07.0
fd400000-fd4007ff : ohci1394
fd700000-fd77ffff : 0000:00:0c.0
fd800000-fd807fff : 0000:00:0c.0
fd800000-fd807fff : sata_sil24
fd900000-fd90007f : 0000:00:0c.0
fd900000-fd90007f : sata_sil24
fda00000-fda1ffff : 0000:00:0d.0
fdb00000-fdb00fff : 0000:00:0d.0
fdb00000-fdb00fff : aic7xxx
fdc00000-fdc1ffff : 0000:00:0e.0
fdd00000-fdd1ffff : 0000:00:0e.0
fdd00000-fdd1ffff : e1000
fde00000-fde1ffff : 0000:00:0e.0
fde00000-fde1ffff : e1000
fdf00000-fdf000ff : 0000:00:10.4
fdf00000-fdf000ff : ehci_hcd
fec00000-fec00fff : IOAPIC 0
fec00000-fec00fff : pnp 00:0a
fee00000-fee00fff : Local APIC
fff80000-ffffffff : reserved
BigMouth scripts # lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host
Bridge (rev 01)
Subsystem: ASUSTeK Computer Inc. K8V Deluxe/K8V-X motherboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at <ignored> (32-bit, prefetchable)
Capabilities: [80] AGP version 3.5
Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 1.02
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge
[K8T800/K8T890 South] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fc500000-fcafffff
Prefetchable memory behind bridge: b3e00000-f3dfffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A8V Deluxe
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fd400000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at cc00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Multimedia audio controller: Creative Labs SB0400 Audigy2 Value
Subsystem: Creative Labs Unknown device 1001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at dc00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 RAID bus controller: Silicon Image, Inc. SiI 3124 PCI-X Serial
ATA Controller (rev 02)
Subsystem: Silicon Image, Inc. Unknown device 7124
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr-
Stepping+ SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fd900000 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at fd800000 (64-bit, non-prefetchable) [size=32K]
Region 4: I/O ports at ec00 [size=16]
Expansion ROM at fd700000 [disabled] [size=512K]
Capabilities: [64] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=12
Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=2048 DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz-
Capabilities: [54] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:0d.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
Subsystem: Adaptec 29160N Ultra160 SCSI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
BIST result: 00
Region 0: I/O ports at b000 [disabled] [size=256]
Region 1: Memory at fdb00000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at fda00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 Ethernet controller: Intel Corporation 82541GI/PI Gigabit
Ethernet Controller
Subsystem: Intel Corporation PRO/1000 MT Desktop Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fde00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fdd00000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at b400 [size=64]
Expansion ROM at fdc00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple
DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID
Controller (rev 80)
Subsystem: ASUSTeK Computer Inc. A7V600/K8V Deluxe/K8V-X/A8V Deluxe
motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at e800 [size=8]
Region 1: I/O ports at e400 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at d800 [size=4]
Region 4: I/O ports at d400 [size=16]
Region 5: I/O ports at d000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 20
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at c000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at c400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if
20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 21
Region 0: Memory at fdf00000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
[KT600/K8T800/K8T890 South]
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
Subsystem: ASUSTeK Computer Inc. Unknown device 80f3
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 0
Region 0: I/O ports at 1000 [disabled] [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem
Controller (rev 80)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 0
Region 0: I/O ports at 1400 [disabled] [size=256]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 AQ [Radeon
9600] (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. A9600SE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at a000 [size=256]
Region 2: Memory at fca00000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fc900000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.1 Display controller: ATI Technologies Inc RV350 AQ [Radeon 9600]
(Secondary)
Subsystem: ASUSTeK Computer Inc. A9600SE (Secondary)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: Memory at fc800000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
BigMouth scripts # cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: SEAGATE Model: ST318452LW Rev: 0004
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: YAMAHA Model: CRW8824S Rev: 1.00
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: ST3300831A Rev: 3.03
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 05 Id: 00 Lun: 00
Vendor: ATA Model: Config Disk Rev: PLS1
Type: Direct-Access ANSI SCSI revision: 05
Tejun Heo wrote:
> Andrew Ryder wrote:
>
>> Hello,
>>
>> Are you still looking an extra person to test your driver for the
>> SiliconImage 4726?
>>
>> I have a Sil3124 raid controller and a mini-storage tower with the
>> sil4726 hardware Port-Multiplier, both from Addonics.
>>
>> So far I havn't been able to get my hardware combination to work, I have
>> applied your latest patch to the 2.6.23 kernel and only the first drive
>> on the HPM (I have 4 300gb drives installed) is detected and usable. The
>> 2nd drive is partially detected, but does not work.
>>
>
> I have reports of detection failure but yours sounds like PMP support is
> not there at all. Please
>
> * cc linux-ide@vger.kernel.org
>
> * try 2.6.24-rc5 and post the kernel boot log
>
>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2007-12-22 13:53 ` Andrew Ryder
@ 2008-01-07 16:12 ` Tejun Heo
2008-01-07 22:28 ` Andrew Ryder
0 siblings, 1 reply; 26+ messages in thread
From: Tejun Heo @ 2008-01-07 16:12 UTC (permalink / raw)
To: Andrew Ryder; +Cc: linux-ide
Andrew Ryder wrote:
> I've attached the boot log from the 2.6.24-rc5 kernel. The problem
> repeats itself in the same manner as with the 2.6.23 kernel with the
> libata patches.
>
> Here is the info on the sata controller and HPM.
>
> Addonics:
>
> - 4 port Sata II Raid5 HBA with the SIL3124 (ADSA4R5)
> - Mini-Storage tower with HPM (AD5SAHPM-E)
> - 2 meter eSata cable
> - One IDE-Sata converter for each IDE drive (ADIDESA)
>
> I have 4 seagate 300GB IDE drives installed in the storage tower, each
> drive has an ide-sata converter installed on it, and the HPM running in
> JBOD mode.
>
> I have upgraded the firmware on the HBA to the latest available from SI
> (6.4.09) and the HPM in the storage tower is running the latest version
> also (1.2061)
>
> Once the driver has finished attempting to initialize the hardware, the
> first hard drive is accessible, the 2nd drive is partially detected, but
> unusable. If I try and run fdisk on the 2nd drive, fdisk reports that
> "You must set cylinders" before attempting partitioning. The 3rd and 4th
> drives are not detected at all.
>
> I have tried the sata controller and HPM under windows 2000, and
> everything worked without issue.
>
> I did try previously configuring the HPM in Raid 1 mode to treat the
> storage tower as one large disk and this configuration worked without
> issue in Linux or windows. Since I returned the unit to JBOD mode, there
> have been some additional errors about trying to access beyond the end
> of the first drive on the HPM.
>
> If theres any other information you need, please let me know.
>
> Thanks
>
> Here is my system config, software environment and boot logs:
>
>
> Hardware:
> Asus SK8V
> Opteron 144
> 2GB Memory
> Adaptec 29160N
> 1 U160 18GB scsi drive
> 1 Ultra scsi cd-rom
> 2 ide drives
> 2 ide cdroms
> Intel Pro/1000 network card
> ATI Radeon 9600 AGP
> Creative Audigy2 sound card
Do you still see this problem on rc6?
--
tejun
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-07 16:12 ` Tejun Heo
@ 2008-01-07 22:28 ` Andrew Ryder
2008-01-08 3:54 ` Tejun Heo
0 siblings, 1 reply; 26+ messages in thread
From: Andrew Ryder @ 2008-01-07 22:28 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-ide
[-- Attachment #1: Type: text/plain, Size: 2760 bytes --]
Yes the issue is still there. I have also tried it with 2.6.24-rc6-git4.
BootLog1.txt
2.6.24-rc6-git4: machine booting up, drive array on before machine is
powered on, drive array is configured as one large disk (RAID-1).
Bootlog2.txt
Same kernel as #1, system has been up for a day or two, drive array was
turned off after the boot failure in #1 and I turned it on again to see
if it made any difference.
Bootlog3.txt
Booted system, drive array already on, kernel 2.6.24-rc6 and the drive
array was configured as one large disk (RAID-1).
Bootlog4.txt
Same as #3, but drive array was configured in JBOD mode.
If you have any not too dangerous fixes you want to test, let me know. I
can give them a try on my hardware here.
Tejun Heo wrote:
> Andrew Ryder wrote:
>
>> I've attached the boot log from the 2.6.24-rc5 kernel. The problem
>> repeats itself in the same manner as with the 2.6.23 kernel with the
>> libata patches.
>>
>> Here is the info on the sata controller and HPM.
>>
>> Addonics:
>>
>> - 4 port Sata II Raid5 HBA with the SIL3124 (ADSA4R5)
>> - Mini-Storage tower with HPM (AD5SAHPM-E)
>> - 2 meter eSata cable
>> - One IDE-Sata converter for each IDE drive (ADIDESA)
>>
>> I have 4 seagate 300GB IDE drives installed in the storage tower, each
>> drive has an ide-sata converter installed on it, and the HPM running in
>> JBOD mode.
>>
>> I have upgraded the firmware on the HBA to the latest available from SI
>> (6.4.09) and the HPM in the storage tower is running the latest version
>> also (1.2061)
>>
>> Once the driver has finished attempting to initialize the hardware, the
>> first hard drive is accessible, the 2nd drive is partially detected, but
>> unusable. If I try and run fdisk on the 2nd drive, fdisk reports that
>> "You must set cylinders" before attempting partitioning. The 3rd and 4th
>> drives are not detected at all.
>>
>> I have tried the sata controller and HPM under windows 2000, and
>> everything worked without issue.
>>
>> I did try previously configuring the HPM in Raid 1 mode to treat the
>> storage tower as one large disk and this configuration worked without
>> issue in Linux or windows. Since I returned the unit to JBOD mode, there
>> have been some additional errors about trying to access beyond the end
>> of the first drive on the HPM.
>>
>> If theres any other information you need, please let me know.
>>
>> Thanks
>>
>> Here is my system config, software environment and boot logs:
>>
>>
>> Hardware:
>> Asus SK8V
>> Opteron 144
>> 2GB Memory
>> Adaptec 29160N
>> 1 U160 18GB scsi drive
>> 1 Ultra scsi cd-rom
>> 2 ide drives
>> 2 ide cdroms
>> Intel Pro/1000 network card
>> ATI Radeon 9600 AGP
>> Creative Audigy2 sound card
>>
>
> Do you still see this problem on rc6?
>
>
[-- Attachment #2: Bootlog1.txt --]
[-- Type: text/plain, Size: 11181 bytes --]
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
libata version 3.00 loaded.
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 0:0:3:0: Attached scsi generic sg1 type 5
sata_sil24 0000:00:0c.0: version 1.1
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Disallowing DAC for device 0000:00:0c.0
scsi1 : sata_sil24
scsi2 : sata_sil24
input: Power Button (FF) as /class/input/input2
scsi3 : sata_sil24
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
scsi4 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
usbcore: registered new device driver usb
ACPI: Sleep Button (CM) [SLPB]
USB Universal Host Controller Interface driver v3.0
input: PC Speaker as /class/input/input5
Floppy drive(s): fd0 is 1.44M
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
FDC 0 is a post-1991 82077
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 3 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: limiting SATA link speed to 1.5 Gbps
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.01: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: limiting SATA link speed to 1.5 Gbps
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.02: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1: EH complete
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 0)
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
Audigy2 value: Special config.
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Disallowing DAC for device 0000:00:0e.0
e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
ReiserFS: hdb1: Using r5 hash to sort names
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
hda: UDMA/100 mode selected
hdb: UDMA/133 mode selected
hdc: UDMA/33 mode selected
hdd: UDMA/33 mode selected
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
w83627hf: Found W83697HF chip at 0x290
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata1.15: irq_stat 0x01140010, PHY RDY changed
ata1: SError: { 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: limiting SATA link speed to 1.5 Gbps
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: failed to recover PMP after 5 tries, giving up
ata1.15: Port Multiplier detaching
ata1.00: disabled
ata1: hard resetting link
ata1: SATA link down (SStatus 1 SControl 0)
ata1: EH complete
[-- Attachment #3: Bootlog2.txt --]
[-- Type: text/plain, Size: 4654 bytes --]
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata1: irq_stat 0x00a40080, device exchanged
ata1: SError: { PHYRdyChg }
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 3 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: limiting SATA link speed to 1.5 Gbps
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.01: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: limiting SATA link speed to 1.5 Gbps
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.02: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1: EH complete
[-- Attachment #4: Bootlog3.txt --]
[-- Type: text/plain, Size: 20476 bytes --]
Linux version 2.6.24-rc6 (root@BigMouth) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #1 Mon Jan 7 15:56:31 EST 2008
Command line: root=/dev/sda3
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff30000 (usable)
BIOS-e820: 000000007ff30000 - 000000007ff40000 (ACPI data)
BIOS-e820: 000000007ff40000 - 000000007fff0000 (ACPI NVS)
BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 524080) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.3 present.
ACPI: RSDP 000FA850, 0014 (r0 ACPIAM)
ACPI: RSDT 7FF30000, 0030 (r1 A M I OEMRSDT 6000517 MSFT 97)
ACPI: FACP 7FF30200, 0081 (r1 A M I OEMFACP 6000517 MSFT 97)
ACPI: DSDT 7FF303F0, 38EA (r1 SK8V_ SK8V_033 33 MSFT 100000D)
ACPI: FACS 7FF40000, 0040
ACPI: APIC 7FF30390, 0052 (r1 A M I OEMAPIC 6000517 MSFT 97)
ACPI: OEMB 7FF40040, 003F (r1 A M I OEMBIOS 6000517 MSFT 97)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 524080) 1 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 524080
On node 0 totalpages: 523983
DMA zone: 56 pages used for memmap
DMA zone: 966 pages reserved
DMA zone: 2977 pages, LIFO batch:0
DMA32 zone: 7109 pages used for memmap
DMA32 zone: 512875 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ff80000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515852
Kernel command line: root=/dev/sda3
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
time.c: Detected 1802.297 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ f8000000 size 64 MB
Memory: 2059868k/2096320k available (2288k kernel code, 35692k reserved, 1038k data, 192k init)
Calibrating delay using timer specific routine.. 3608.83 BogoMIPS (lpj=7217673)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Opteron(tm) Processor 144 stepping 0a
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12515958
Detected 12.515 MHz APIC timer.
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: enabled onboard AC97/MC97 devices
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf8000000
Time: tsc clocksource has been installed.
system 00:09: ioport range 0x295-0x296 has been reserved
system 00:09: ioport range 0x3e1-0x3e7 has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x800-0x87f has been reserved
system 00:09: ioport range 0x400-0x41f has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xdffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
system 00:0d: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: fc500000-fcafffff
PREFETCH window: b3e00000-f3dfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1199739639.260:1): initialized
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VIA8237SATA: IDE controller (0x1106:0x3149 rev 0x80) at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
VIA8237SATA: 100% native mode on irq 20
ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: Maxtor 4G160J8, ATA DISK drive
hda: ST3200822A, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/133 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/33 mode selected
hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
hdd: UDMA/33 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
hda: cache flushes supported
hda: hda1 hda2
hdb: max request size: 512KiB
hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63
hdb: cache flushes not supported
hdb: hdb1
hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
target0:0:0: Beginning Domain Validation
target0:0:0: wide asynchronous
target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target0:0:0: Ending Domain Validation
scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
target0:0:3: Beginning Domain Validation
target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
target0:0:3: Domain Validation skipping write tests
target0:0:3: Ending Domain Validation
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
sr 0:0:3:0: Attached scsi CD-ROM sr0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 33
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
libata version 3.00 loaded.
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 0:0:3:0: Attached scsi generic sg1 type 5
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: Sleep Button (CM) [SLPB]
sata_sil24 0000:00:0c.0: version 1.1
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Disallowing DAC for device 0000:00:0c.0
scsi1 : sata_sil24
scsi2 : sata_sil24
scsi3 : sata_sil24
scsi4 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
input: PC Speaker as /class/input/input5
Floppy drive(s): fd0 is 1.44M
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
FDC 0 is a post-1991 82077
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 3 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: limiting SATA link speed to 1.5 Gbps
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.01: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: limiting SATA link speed to 1.5 Gbps
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.02: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link down (SStatus 0 SControl 0)
ata1: EH complete
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 0)
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
Audigy2 value: Special config.
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Disallowing DAC for device 0000:00:0e.0
e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
hda: UDMA/100 mode selected
hdb: UDMA/133 mode selected
hdc: UDMA/33 mode selected
hdd: UDMA/33 mode selected
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
w83627hf: Found W83697HF chip at 0x290
[-- Attachment #5: Bootlog4.txt --]
[-- Type: text/plain, Size: 30743 bytes --]
31072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ f8000000 size 64 MB
Memory: 2059868k/2096320k available (2288k kernel code, 35692k reserved, 1038k data, 192k init)
Calibrating delay using timer specific routine.. 3608.83 BogoMIPS (lpj=7217673)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Opteron(tm) Processor 144 stepping 0a
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12515973
Detected 12.515 MHz APIC timer.
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: enabled onboard AC97/MC97 devices
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf8000000
Time: tsc clocksource has been installed.
system 00:09: ioport range 0x295-0x296 has been reserved
system 00:09: ioport range 0x3e1-0x3e7 has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x800-0x87f has been reserved
system 00:09: ioport range 0x400-0x41f has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xdffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
system 00:0d: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: fc500000-fcafffff
PREFETCH window: b3e00000-f3dfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1199743005.260:1): initialized
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VIA8237SATA: IDE controller (0x1106:0x3149 rev 0x80) at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
VIA8237SATA: 100% native mode on irq 20
ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: Maxtor 4G160J8, ATA DISK drive
hda: ST3200822A, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/133 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/33 mode selected
hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
hdd: UDMA/33 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
hda: cache flushes supported
hda: hda1 hda2
hdb: max request size: 512KiB
hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63
hdb: cache flushes not supported
hdb: hdb1
hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
target0:0:0: Beginning Domain Validation
target0:0:0: wide asynchronous
target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target0:0:0: Ending Domain Validation
scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
target0:0:3: Beginning Domain Validation
target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
target0:0:3: Domain Validation skipping write tests
target0:0:3: Ending Domain Validation
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
sr 0:0:3:0: Attached scsi CD-ROM sr0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 33
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 0:0:3:0: Attached scsi generic sg1 type 5
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
input: Power Button (FF) as /class/input/input2
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
sata_sil24 0000:00:0c.0: version 1.1
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Disallowing DAC for device 0000:00:0c.0
scsi1 : sata_sil24
scsi2 : sata_sil24
scsi3 : sata_sil24
scsi4 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
input: PC Speaker as /class/input/input5
Floppy drive(s): fd0 is 1.44M
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
FDC 0 is a post-1991 82077
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: limiting SATA link speed to 1.5 Gbps
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.01: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: limiting SATA link speed to 1.5 Gbps
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.02: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 35 secs
ata1.03: limiting SATA link speed to 1.5 Gbps
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed, giving up
ata1.15: hard resetting link
ata1.15: softreset failed (SRST command error)
ata1.15: reset failed (errno=-5), retrying in 8 secs
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 35 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed, giving up
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 35 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed, giving up
ata1.03: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 320)
ata1.05: hard resetting link
ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.00: 586072368 sectors, multi 16: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata1.05: 640 sectors, multi 1: LBA
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x1 t4
ata1.00: irq_stat 0x00020002, failed to transmit command FIS
ata1.00: configured for UDMA/100
ata1: EH complete
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 0)
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sdb: p1 exceeds device capacity
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sdc] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdc] Write Protect is off
sd 1:5:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdc] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdc] Write Protect is off
sd 1:5:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdc: unknown partition table
sd 1:5:0:0: [sdc] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg3 type 0
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
Audigy2 value: Special config.
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
attempt to access beyond end of device
sdb: rw=0, want=2340413248, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413184
attempt to access beyond end of device
sdb: rw=0, want=2340413249, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413185
attempt to access beyond end of device
sdb: rw=0, want=2340413250, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413186
attempt to access beyond end of device
sdb: rw=0, want=2340413251, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413187
attempt to access beyond end of device
sdb: rw=0, want=2340413252, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413188
attempt to access beyond end of device
sdb: rw=0, want=2340413253, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413189
attempt to access beyond end of device
sdb: rw=0, want=2340413254, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413190
attempt to access beyond end of device
sdb: rw=0, want=2340413255, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413191
attempt to access beyond end of device
sdb: rw=0, want=2340413248, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413184
attempt to access beyond end of device
sdb: rw=0, want=2340413249, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413185
attempt to access beyond end of device
sdb: rw=0, want=2340413250, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413251, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413252, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413253, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413254, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413255, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413440, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413441, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413442, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413443, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413444, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413445, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413446, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413447, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413440, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413441, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413442, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413443, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413444, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413445, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413446, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413447, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413392, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413393, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413394, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413395, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413396, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413397, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413398, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413399, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413448, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413449, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413450, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413451, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413452, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413453, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413454, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413455, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Disallowing DAC for device 0000:00:0e.0
e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
hda: UDMA/100 mode selected
hdb: UDMA/133 mode selected
hdc: UDMA/33 mode selected
hdd: UDMA/33 mode selected
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
w83627hf: Found W83697HF chip at 0x290
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-07 22:28 ` Andrew Ryder
@ 2008-01-08 3:54 ` Tejun Heo
2008-01-08 8:00 ` Andrew Ryder
0 siblings, 1 reply; 26+ messages in thread
From: Tejun Heo @ 2008-01-08 3:54 UTC (permalink / raw)
To: Andrew Ryder; +Cc: linux-ide
Hello,
Andrew Ryder wrote:
> Yes the issue is still there. I have also tried it with 2.6.24-rc6-git4.
>
> BootLog1.txt
> 2.6.24-rc6-git4: machine booting up, drive array on before machine is
> powered on, drive array is configured as one large disk (RAID-1).
>
> Bootlog2.txt
> Same kernel as #1, system has been up for a day or two, drive array was
> turned off after the boot failure in #1 and I turned it on again to see
> if it made any difference.
>
> Bootlog3.txt
> Booted system, drive array already on, kernel 2.6.24-rc6 and the drive
> array was configured as one large disk (RAID-1).
>
> Bootlog4.txt
> Same as #3, but drive array was configured in JBOD mode.
>
> If you have any not too dangerous fixes you want to test, let me know. I
> can give them a try on my hardware here.
Hmmmm... This is weird. I have two reports on addonics reporting the
same problem now.
In boot log 1 and 3, the first fan-out port (ata1.00) is down while on 2
and 4, the link is up. Was there any hardware configuration change?
4726 is known to malfunction if the first port isn't occupied.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-08 3:54 ` Tejun Heo
@ 2008-01-08 8:00 ` Andrew Ryder
2008-01-09 5:45 ` Tejun Heo
0 siblings, 1 reply; 26+ messages in thread
From: Andrew Ryder @ 2008-01-08 8:00 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-ide
[-- Attachment #1: Type: text/plain, Size: 1524 bytes --]
The only configuration change is that in Bootlog4 I switched the 4726
back to JBOD mode instead of RAID-1 mode. No physical cabling has been
changed.
I've attached a screenshot showing the configuration in JBOD mode from
the 3124's view.
When I rebooted this morning, there was no indication of ATA1.00 being
shown as down (attached Bootlog5.txt).
Tejun Heo wrote:
> Hello,
>
> Andrew Ryder wrote:
>
>> Yes the issue is still there. I have also tried it with 2.6.24-rc6-git4.
>>
>> BootLog1.txt
>> 2.6.24-rc6-git4: machine booting up, drive array on before machine is
>> powered on, drive array is configured as one large disk (RAID-1).
>>
>> Bootlog2.txt
>> Same kernel as #1, system has been up for a day or two, drive array was
>> turned off after the boot failure in #1 and I turned it on again to see
>> if it made any difference.
>>
>> Bootlog3.txt
>> Booted system, drive array already on, kernel 2.6.24-rc6 and the drive
>> array was configured as one large disk (RAID-1).
>>
>> Bootlog4.txt
>> Same as #3, but drive array was configured in JBOD mode.
>>
>> If you have any not too dangerous fixes you want to test, let me know. I
>> can give them a try on my hardware here.
>>
>
> Hmmmm... This is weird. I have two reports on addonics reporting the
> same problem now.
>
> In boot log 1 and 3, the first fan-out port (ata1.00) is down while on 2
> and 4, the link is up. Was there any hardware configuration change?
> 4726 is known to malfunction if the first port isn't occupied.
>
> Thanks.
>
>
[-- Attachment #2: sata_config.jpg --]
[-- Type: image/jpeg, Size: 71633 bytes --]
[-- Attachment #3: Bootlog5.txt --]
[-- Type: text/plain, Size: 30740 bytes --]
fic routine.. 3608.83 BogoMIPS (lpj=7217674)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Opteron(tm) Processor 144 stepping 0a
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12515989
Detected 12.515 MHz APIC timer.
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: enabled onboard AC97/MC97 devices
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf8000000
Time: tsc clocksource has been installed.
system 00:09: ioport range 0x295-0x296 has been reserved
system 00:09: ioport range 0x3e1-0x3e7 has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x800-0x87f has been reserved
system 00:09: ioport range 0x400-0x41f has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xdffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
system 00:0d: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: fc500000-fcafffff
PREFETCH window: b3e00000-f3dfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1199778079.260:1): initialized
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VIA8237SATA: IDE controller (0x1106:0x3149 rev 0x80) at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
VIA8237SATA: 100% native mode on irq 20
ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: Maxtor 4G160J8, ATA DISK drive
hda: ST3200822A, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/133 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/33 mode selected
hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
hdd: UDMA/33 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
hda: cache flushes supported
hda: hda1 hda2
hdb: max request size: 512KiB
hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63
hdb: cache flushes not supported
hdb: hdb1
hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
target0:0:0: Beginning Domain Validation
target0:0:0: wide asynchronous
target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target0:0:0: Ending Domain Validation
scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
target0:0:3: Beginning Domain Validation
target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
target0:0:3: Domain Validation skipping write tests
target0:0:3: Ending Domain Validation
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
sr 0:0:3:0: Attached scsi CD-ROM sr0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 33
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
libata version 3.00 loaded.
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 0:0:3:0: Attached scsi generic sg1 type 5
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: Sleep Button (CM) [SLPB]
sata_sil24 0000:00:0c.0: version 1.1
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Disallowing DAC for device 0000:00:0c.0
scsi1 : sata_sil24
scsi2 : sata_sil24
scsi3 : sata_sil24
scsi4 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
input: PC Speaker as /class/input/input5
Floppy drive(s): fd0 is 1.44M
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
FDC 0 is a post-1991 82077
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: limiting SATA link speed to 1.5 Gbps
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.15: hard resetting link
ata1.15: softreset failed (SRST command error)
ata1.15: reset failed (errno=-5), retrying in 8 secs
ReiserFS: sda3: Removing [1537339 6814138 0x0 SD]..done
ReiserFS: sda3: There were 1 uncompleted unlinks/truncates. Completed
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 10 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed (errno=-5), retrying in 35 secs
ata1.01: hard resetting link
ata1.01: softreset failed (SRST command error)
ata1.01: reset failed, giving up
ata1.01: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: limiting SATA link speed to 1.5 Gbps
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.15: hard resetting link
ata1.15: softreset failed (SRST command error)
ata1.15: reset failed (errno=-5), retrying in 8 secs
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 10 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed (errno=-5), retrying in 35 secs
ata1.02: hard resetting link
ata1.02: softreset failed (SRST command error)
ata1.02: reset failed, giving up
ata1.02: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 35 secs
ata1.03: limiting SATA link speed to 1.5 Gbps
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed, giving up
ata1.15: hard resetting link
ata1.15: softreset failed (SRST command error)
ata1.15: reset failed (errno=-5), retrying in 8 secs
ata1.15: hard resetting link
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 35 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed, giving up
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 10 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed (errno=-5), retrying in 35 secs
ata1.03: hard resetting link
ata1.03: softreset failed (SRST command error)
ata1.03: reset failed, giving up
ata1.03: failed to recover link after 3 tries, disabling
ata1: failed to recover PMP, retrying in 5 secs
ata1.15: hard resetting link
ata1: controller in dubious state, performing PORT_RST
ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 320)
ata1.05: hard resetting link
ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.00: 586072368 sectors, multi 16: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata1.05: 640 sectors, multi 1: LBA
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1.00: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x1 t4
ata1.00: irq_stat 0x00020002, failed to transmit command FIS
ata1.00: configured for UDMA/100
ata1: EH complete
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 0)
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sdb: p1 exceeds device capacity
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sdc] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdc] Write Protect is off
sd 1:5:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdc] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdc] Write Protect is off
sd 1:5:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdc: unknown partition table
sd 1:5:0:0: [sdc] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg3 type 0
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
Audigy2 value: Special config.
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
attempt to access beyond end of device
sdb: rw=0, want=2340413248, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413184
attempt to access beyond end of device
sdb: rw=0, want=2340413249, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413185
attempt to access beyond end of device
sdb: rw=0, want=2340413250, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413186
attempt to access beyond end of device
sdb: rw=0, want=2340413251, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413187
attempt to access beyond end of device
sdb: rw=0, want=2340413252, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413188
attempt to access beyond end of device
sdb: rw=0, want=2340413253, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413189
attempt to access beyond end of device
sdb: rw=0, want=2340413254, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413190
attempt to access beyond end of device
sdb: rw=0, want=2340413255, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413191
attempt to access beyond end of device
sdb: rw=0, want=2340413248, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413184
attempt to access beyond end of device
sdb: rw=0, want=2340413249, limit=586072368
Buffer I/O error on device sdb1, logical block 2340413185
attempt to access beyond end of device
sdb: rw=0, want=2340413250, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413251, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413252, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413253, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413254, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413255, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413440, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413441, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413442, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413443, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413444, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413445, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413446, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413447, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413440, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413441, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413442, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413443, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413444, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413445, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413446, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413447, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413392, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413393, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413394, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413395, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413396, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413397, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413398, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413399, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413448, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413449, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413450, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413451, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413452, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413453, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413454, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413455, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413456, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413457, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413458, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413459, limit=586072368
attempt to access beyond end of device
sdb: rw=0, want=2340413460, limit=586072368
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Disallowing DAC for device 0000:00:0e.0
e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
hda: UDMA/100 mode selected
hdb: UDMA/133 mode selected
hdc: UDMA/33 mode selected
hdd: UDMA/33 mode selected
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
w83627hf: Found W83697HF chip at 0x290
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-08 8:00 ` Andrew Ryder
@ 2008-01-09 5:45 ` Tejun Heo
2008-01-09 17:47 ` Andrew Ryder
2008-01-10 3:29 ` Tejun Heo
0 siblings, 2 replies; 26+ messages in thread
From: Tejun Heo @ 2008-01-09 5:45 UTC (permalink / raw)
To: Andrew Ryder, Gaston, Jason D; +Cc: linux-ide
[-- Attachment #1: Type: text/plain, Size: 96 bytes --]
Please apply the attached patch on top of 2.6.24-rc7 and report the
result. Thanks.
--
tejun
[-- Attachment #2: simg-pmp-quirk.patch --]
[-- Type: text/x-patch, Size: 1173 bytes --]
diff --git a/drivers/ata/libata-pmp.c b/drivers/ata/libata-pmp.c
index c0c4dbc..c07566c 100644
--- a/drivers/ata/libata-pmp.c
+++ b/drivers/ata/libata-pmp.c
@@ -467,7 +467,8 @@ static void sata_pmp_quirks(struct ata_port *ap)
/* class code report is unreliable */
if (link->pmp < 5)
- link->flags |= ATA_LFLAG_ASSUME_ATA;
+ link->flags |= ATA_LFLAG_NO_SRST |
+ ATA_LFLAG_ASSUME_ATA;
/* port 5 is for SEMB device and it doesn't like SRST */
if (link->pmp == 5)
@@ -482,7 +483,8 @@ static void sata_pmp_quirks(struct ata_port *ap)
/* class code report is unreliable */
if (link->pmp < 2)
- link->flags |= ATA_LFLAG_ASSUME_ATA;
+ link->flags |= ATA_LFLAG_NO_SRST |
+ ATA_LFLAG_ASSUME_ATA;
/* the config device at port 2 locks up on SRST */
if (link->pmp == 2)
@@ -497,7 +499,8 @@ static void sata_pmp_quirks(struct ata_port *ap)
/* class code report is unreliable */
if (link->pmp < 5)
- link->flags |= ATA_LFLAG_ASSUME_ATA;
+ link->flags |= ATA_LFLAG_NO_SRST |
+ ATA_LFLAG_ASSUME_ATA;
/* The config device, which can be either at
* port 0 or 5, locks up on SRST.
^ permalink raw reply related [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-09 5:45 ` Tejun Heo
@ 2008-01-09 17:47 ` Andrew Ryder
2008-01-10 0:53 ` Tejun Heo
2008-01-10 3:29 ` Tejun Heo
1 sibling, 1 reply; 26+ messages in thread
From: Andrew Ryder @ 2008-01-09 17:47 UTC (permalink / raw)
To: Tejun Heo, linux-ide
[-- Attachment #1: Type: text/plain, Size: 936 bytes --]
It works.
Boot log is attached.
I ran mke2fs on all 4 drives simultaneously and all is . I did notice
that DMA was disabled on the hardware? Do you need any info from my side
for this?
Should device node sdf on the 5th port exist even though no drive is
installed on the 5th port?
Thanks
cat /proc/partitions
major minor #blocks name
3 0 195360984 hda
3 1 19454683 hda1
3 2 175903717 hda2
3 64 160086528 hdb
3 65 160079661 hdb1
8 0 17921835 sda
8 1 56196 sda1
8 2 987997 sda2
8 3 16876282 sda3
8 16 293036184 sdb
8 17 293033601 sdb1
8 32 293036184 sdc
8 33 293033601 sdc1
8 48 293036184 sdd
8 49 293033601 sdd1
8 64 293036184 sde
8 65 293033601 sde1
8 80 320 sdf
Tejun Heo wrote:
> Please apply the attached patch on top of 2.6.24-rc7 and report the
> result. Thanks.
>
>
[-- Attachment #2: success1.txt --]
[-- Type: text/plain, Size: 22828 bytes --]
Linux version 2.6.24-rc7 (root@BigMouth) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #1 Wed Jan 9 07:41:02 EST 2008
Command line: root=/dev/sda3
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff30000 (usable)
BIOS-e820: 000000007ff30000 - 000000007ff40000 (ACPI data)
BIOS-e820: 000000007ff40000 - 000000007fff0000 (ACPI NVS)
BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 524080) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.3 present.
ACPI: RSDP 000FA850, 0014 (r0 ACPIAM)
ACPI: RSDT 7FF30000, 0030 (r1 A M I OEMRSDT 6000517 MSFT 97)
ACPI: FACP 7FF30200, 0081 (r1 A M I OEMFACP 6000517 MSFT 97)
ACPI: DSDT 7FF303F0, 38EA (r1 SK8V_ SK8V_033 33 MSFT 100000D)
ACPI: FACS 7FF40000, 0040
ACPI: APIC 7FF30390, 0052 (r1 A M I OEMAPIC 6000517 MSFT 97)
ACPI: OEMB 7FF40040, 003F (r1 A M I OEMBIOS 6000517 MSFT 97)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 524080) 1 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 524080
On node 0 totalpages: 523983
DMA zone: 56 pages used for memmap
DMA zone: 964 pages reserved
DMA zone: 2979 pages, LIFO batch:0
DMA32 zone: 7109 pages used for memmap
DMA32 zone: 512875 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ff80000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515854
Kernel command line: root=/dev/sda3
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
time.c: Detected 1802.297 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ f8000000 size 64 MB
Memory: 2059876k/2096320k available (2288k kernel code, 35684k reserved, 1034k data, 192k init)
Calibrating delay using timer specific routine.. 3608.83 BogoMIPS (lpj=7217676)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Opteron(tm) Processor 144 stepping 0a
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12515958
Detected 12.515 MHz APIC timer.
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: enabled onboard AC97/MC97 devices
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf8000000
Time: tsc clocksource has been installed.
system 00:09: ioport range 0x295-0x296 has been reserved
system 00:09: ioport range 0x3e1-0x3e7 has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x800-0x87f has been reserved
system 00:09: ioport range 0x400-0x41f has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xdffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
system 00:0d: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: fc500000-fcafffff
PREFETCH window: b3e00000-f3dfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1199882600.256:1): initialized
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VIA8237SATA: IDE controller (0x1106:0x3149 rev 0x80) at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
VIA8237SATA: 100% native mode on irq 20
ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: Maxtor 4G160J8, ATA DISK drive
hda: ST3200822A, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/133 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/33 mode selected
hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
hdd: UDMA/33 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
hda: cache flushes supported
hda: hda1 hda2
hdb: max request size: 512KiB
hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63
hdb: cache flushes not supported
hdb: hdb1
hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
target0:0:0: Beginning Domain Validation
target0:0:0: wide asynchronous
target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target0:0:0: Ending Domain Validation
scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
target0:0:3: Beginning Domain Validation
target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
target0:0:3: Domain Validation skipping write tests
target0:0:3: Ending Domain Validation
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
sr 0:0:3:0: Attached scsi CD-ROM sr0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 33
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 0:0:3:0: Attached scsi generic sg1 type 5
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: Sleep Button (CM) [SLPB]
sata_sil24 0000:00:0c.0: version 1.1
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Disallowing DAC for device 0000:00:0c.0
scsi1 : sata_sil24
scsi2 : sata_sil24
scsi3 : sata_sil24
scsi4 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
input: PC Speaker as /class/input/input5
Floppy drive(s): fd0 is 1.44M
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
FDC 0 is a post-1991 82077
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 320)
ata1.05: hard resetting link
ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.00: 586072368 sectors, multi 16: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.01: 586072368 sectors, multi 0: LBA48
ata1.01: applying bridge limits
ata1.01: configured for UDMA/100
ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.02: 586072368 sectors, multi 0: LBA48
ata1.02: applying bridge limits
ata1.02: configured for UDMA/100
ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.03: 586072368 sectors, multi 0: LBA48
ata1.03: applying bridge limits
ata1.03: configured for UDMA/100
ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata1.05: 640 sectors, multi 1: LBA
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: EH complete
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 0)
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: unknown partition table
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: [LDM]
sd 1:1:0:0: [sdc] Attached SCSI disk
sd 1:1:0:0: Attached scsi generic sg3 type 0
scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:2:0:0: [sdd] Attached SCSI disk
sd 1:2:0:0: Attached scsi generic sg4 type 0
scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde:
sd 1:3:0:0: [sde] Attached SCSI disk
sd 1:3:0:0: Attached scsi generic sg5 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdf: unknown partition table
sd 1:5:0:0: [sdf] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg6 type 0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
Audigy2 value: Special config.
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Disallowing DAC for device 0000:00:0e.0
e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
hda: UDMA/100 mode selected
hdb: UDMA/133 mode selected
hdc: UDMA/33 mode selected
hdd: UDMA/33 mode selected
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
w83627hf: Found W83697HF chip at 0x290
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-10 3:29 ` Tejun Heo
@ 2008-01-09 23:00 ` Andrew Ryder
2008-01-10 4:20 ` Tejun Heo
0 siblings, 1 reply; 26+ messages in thread
From: Andrew Ryder @ 2008-01-09 23:00 UTC (permalink / raw)
To: Tejun Heo; +Cc: Gaston, Jason D, linux-ide
[-- Attachment #1: Type: text/plain, Size: 698 bytes --]
Tejun,
I rebooted with the 4726 online during bootup, verified everything was
there by re-formatting the fs on each drive. I powered off the 4726 for
approx 15 seconds, turned it back on, and repeated the power on/off
again about 1 minute later.
The first 3 drives are accessible, but the 4th drive on ata1.03 failed
to be recognized.
Tejun Heo wrote:
> Tejun Heo wrote:
>
>> Please apply the attached patch on top of 2.6.24-rc7 and report the
>> result. Thanks.
>>
>
> Andrew, with the patch applied, please try to turn off and on the PMP
> array while the system is running and verify that each time the array
> gets detected correctly and disks are accessible.
>
> Thanks.
>
>
[-- Attachment #2: Bootlog10.txt --]
[-- Type: text/plain, Size: 30858 bytes --]
PFN ranges
0: 0 -> 159
0: 256 -> 524080
On node 0 totalpages: 523983
DMA zone: 56 pages used for memmap
DMA zone: 964 pages reserved
DMA zone: 2979 pages, LIFO batch:0
DMA32 zone: 7109 pages used for memmap
DMA32 zone: 512875 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ff80000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515854
Kernel command line: root=/dev/sda3
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
time.c: Detected 1802.297 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ f8000000 size 64 MB
Memory: 2059876k/2096320k available (2288k kernel code, 35684k reserved, 1034k data, 192k init)
Calibrating delay using timer specific routine.. 3608.84 BogoMIPS (lpj=7217681)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Opteron(tm) Processor 144 stepping 0a
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12515956
Detected 12.515 MHz APIC timer.
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: enabled onboard AC97/MC97 devices
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf8000000
Time: tsc clocksource has been installed.
system 00:09: ioport range 0x295-0x296 has been reserved
system 00:09: ioport range 0x3e1-0x3e7 has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x800-0x87f has been reserved
system 00:09: ioport range 0x400-0x41f has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xdffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
system 00:0d: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: fc500000-fcafffff
PREFETCH window: b3e00000-f3dfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1199918569.256:1): initialized
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VIA8237SATA: IDE controller (0x1106:0x3149 rev 0x80) at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
VIA8237SATA: 100% native mode on irq 20
ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: Maxtor 4G160J8, ATA DISK drive
hda: ST3200822A, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/133 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/33 mode selected
hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
hdd: UDMA/33 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
hda: cache flushes supported
hda: hda1 hda2
hdb: max request size: 512KiB
hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63
hdb: cache flushes not supported
hdb: hdb1
hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
target0:0:0: Beginning Domain Validation
target0:0:0: wide asynchronous
target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target0:0:0: Ending Domain Validation
scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
target0:0:3: Beginning Domain Validation
target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
target0:0:3: Domain Validation skipping write tests
target0:0:3: Ending Domain Validation
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
sr 0:0:3:0: Attached scsi CD-ROM sr0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 33
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 0:0:3:0: Attached scsi generic sg1 type 5
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
input: Power Button (FF) as /class/input/input2
USB Universal Host Controller Interface driver v3.0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
sata_sil24 0000:00:0c.0: version 1.1
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Disallowing DAC for device 0000:00:0c.0
scsi1 : sata_sil24
scsi2 : sata_sil24
scsi3 : sata_sil24
scsi4 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
input: PC Speaker as /class/input/input5
Floppy drive(s): fd0 is 1.44M
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
FDC 0 is a post-1991 82077
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 320)
ata1.05: hard resetting link
ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.00: 586072368 sectors, multi 16: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.01: 586072368 sectors, multi 0: LBA48
ata1.01: applying bridge limits
ata1.01: configured for UDMA/100
ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.02: 586072368 sectors, multi 0: LBA48
ata1.02: applying bridge limits
ata1.02: configured for UDMA/100
ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.03: 586072368 sectors, multi 0: LBA48
ata1.03: applying bridge limits
ata1.03: configured for UDMA/100
ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata1.05: 640 sectors, multi 1: LBA
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: EH complete
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 0)
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 1:1:0:0: [sdc] Attached SCSI disk
sd 1:1:0:0: Attached scsi generic sg3 type 0
scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:2:0:0: [sdd] Attached SCSI disk
sd 1:2:0:0: Attached scsi generic sg4 type 0
scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 1:3:0:0: [sde] Attached SCSI disk
sd 1:3:0:0: Attached scsi generic sg5 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdf: unknown partition table
sd 1:5:0:0: [sdf] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg6 type 0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
Audigy2 value: Special config.
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Disallowing DAC for device 0000:00:0e.0
e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
hda: UDMA/100 mode selected
hdb: UDMA/133 mode selected
hdc: UDMA/33 mode selected
hdd: UDMA/33 mode selected
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
w83627hf: Found W83697HF chip at 0x290
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x90000 action 0xa frozen
ata1.15: irq_stat 0x01b40090, PHY RDY changed
ata1: SError: { PHYRdyChg 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: limiting SATA link speed to 1.5 Gbps
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 310)
ata1.05: hard resetting link
ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.00: revalidation failed (errno=-5)
ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.01: revalidation failed (errno=-5)
ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.02: revalidation failed (errno=-5)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1.03: disabled
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
ata1.03: detaching (SCSI 1:3:0:0)
sd 1:3:0:0: [sde] Synchronizing SCSI cache
sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
sd 1:3:0:0: [sde] Stopping disk
sd 1:3:0:0: [sde] START_STOP FAILED
sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata1.15: irq_stat 0x01940090, PHY RDY changed
ata1: SError: { 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 310)
ata1.05: hard resetting link
ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.00: revalidation failed (errno=-5)
ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.01: revalidation failed (errno=-5)
ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.02: revalidation failed (errno=-5)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-10 4:20 ` Tejun Heo
@ 2008-01-09 23:55 ` Andrew Ryder
2008-01-10 6:36 ` Tejun Heo
0 siblings, 1 reply; 26+ messages in thread
From: Andrew Ryder @ 2008-01-09 23:55 UTC (permalink / raw)
To: Tejun Heo; +Cc: Gaston, Jason D, linux-ide
[-- Attachment #1: Type: text/plain, Size: 1813 bytes --]
This might be of interest.. I had turned the drive off for about 20
minutes, then turned it back on. ata1.03 is now partially there, it is
recognized as a device, but of 0MB in size.
All of this is done with the 4726 turned on..
Bootlog11.txt -> I unplugged the 4726, waited 10 seconds, and plugged it
into the second port on the 3124. All 4 drives are there.
Bootlog12.txt -> I unplugged the 4726 again, waited 10 seconds, plugged
it back into the first (original) port, and ata1.03 is back..
Bootlog13.txt -> I powered the 4726 off, waited 10 seconds, turned it
back on. The same drive is missing now.
Bootlog14.txt -> I unplugged, waited 10 seconds, and re-plugged the 4726
into the same port (first eSATA port) and now ata1.03 is recognized and
accessible.
I'll make sure to turn on the timestamping for you tomorrow. Would want
me to redo this testing so you can have the timestamps also?
Thanks
Tejun Heo wrote:
> Andrew Ryder wrote:
>
>> Tejun,
>>
>> I rebooted with the 4726 online during bootup, verified everything was
>> there by re-formatting the fs on each drive. I powered off the 4726 for
>> approx 15 seconds, turned it back on, and repeated the power on/off
>> again about 1 minute later.
>>
>> The first 3 drives are accessible, but the 4th drive on ata1.03 failed
>> to be recognized.
>>
>
> Hmmm... That's interesting. The fourth drive seemed to have gone out
> for lunch. If you can, does connecting the drive to another port (be it
> PMP port or not) without removing power make the drive work again? If
> you can't do that, does removing the drive and re-plugging revives it?
> Please try to determine who went out for lunch - the PMP port or the
> drive. Also, can you please turn on CONFIG_PRINTK_TIME so that I can
> tell what's happening when?
>
> Thanks.
>
>
[-- Attachment #2: Bootlog11.txt --]
[-- Type: text/plain, Size: 30815 bytes --]
6>hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
Audigy2 value: Special config.
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Disallowing DAC for device 0000:00:0e.0
e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
hda: UDMA/100 mode selected
hdb: UDMA/133 mode selected
hdc: UDMA/33 mode selected
hdd: UDMA/33 mode selected
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
w83627hf: Found W83697HF chip at 0x290
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x90000 action 0xa frozen
ata1.15: irq_stat 0x01b40090, PHY RDY changed
ata1: SError: { PHYRdyChg 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: limiting SATA link speed to 1.5 Gbps
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 310)
ata1.05: hard resetting link
ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.00: revalidation failed (errno=-5)
ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.01: revalidation failed (errno=-5)
ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.02: revalidation failed (errno=-5)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1.03: disabled
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
ata1.03: detaching (SCSI 1:3:0:0)
sd 1:3:0:0: [sde] Synchronizing SCSI cache
sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
sd 1:3:0:0: [sde] Stopping disk
sd 1:3:0:0: [sde] START_STOP FAILED
sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata1.15: irq_stat 0x01940090, PHY RDY changed
ata1: SError: { 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 310)
ata1.05: hard resetting link
ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.00: revalidation failed (errno=-5)
ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.01: revalidation failed (errno=-5)
ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.02: revalidation failed (errno=-5)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata1.15: irq_stat 0x01140010, PHY RDY changed
ata1: SError: { 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: failed to recover PMP after 5 tries, giving up
ata1.15: Port Multiplier detaching
ata1.00: disabled
ata1.01: disabled
ata1.02: disabled
ata1.05: disabled
ata1.00: disabled
ata1: hard resetting link
ata1: SATA link down (SStatus 1 SControl 0)
ata1: EH complete
ata1.00: detaching (SCSI 1:0:0:0)
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
sd 1:0:0:0: [sdb] Stopping disk
sd 1:0:0:0: [sdb] START_STOP FAILED
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
ata1.01: detaching (SCSI 1:1:0:0)
sd 1:1:0:0: [sdc] Synchronizing SCSI cache
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
sd 1:1:0:0: [sdc] Stopping disk
sd 1:1:0:0: [sdc] START_STOP FAILED
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
ata1.02: detaching (SCSI 1:2:0:0)
sd 1:2:0:0: [sdd] Synchronizing SCSI cache
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
sd 1:2:0:0: [sdd] Stopping disk
sd 1:2:0:0: [sdd] START_STOP FAILED
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
ata1.05: detaching (SCSI 1:5:0:0)
sd 1:5:0:0: [sdf] Stopping disk
sd 1:5:0:0: [sdf] START_STOP FAILED
sd 1:5:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata1: irq_stat 0x00a40080, device exchanged
ata1: SError: { PHYRdyChg }
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 320)
ata1.05: hard resetting link
ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata1.05: 640 sectors, multi 1: LBA
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.00: 586072368 sectors, multi 0: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.01: 586072368 sectors, multi 0: LBA48
ata1.01: applying bridge limits
ata1.01: configured for UDMA/100
ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.02: 586072368 sectors, multi 0: LBA48
ata1.02: applying bridge limits
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1: EH complete
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 1:1:0:0: [sdc] Attached SCSI disk
sd 1:1:0:0: Attached scsi generic sg3 type 0
scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:2:0:0: [sdd] Attached SCSI disk
sd 1:2:0:0: Attached scsi generic sg4 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sde] Write Protect is off
sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sde] Write Protect is off
sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sde: unknown partition table
sd 1:5:0:0: [sde] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg5 type 0
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xa frozen
ata1.15: irq_stat 0x01b40090, PHY RDY changed
ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: limiting SATA link speed to 1.5 Gbps
ata1.15: retrying hardreset in 5 secs
ata2: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata2: irq_stat 0x00a40080, device exchanged
ata2: SError: { PHYRdyChg }
ata2: hard resetting link
ata1.15: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata2.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata2.00: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata2.01: hard resetting link
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata2.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.02: hard resetting link
ata2.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.03: hard resetting link
ata2.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.04: hard resetting link
ata2.04: SATA link down (SStatus 0 SControl 320)
ata2.05: hard resetting link
ata2.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata2.06: hard resetting link
ata2.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata2.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata2.00: 586072368 sectors, multi 0: LBA48
ata2.00: applying bridge limits
ata2.00: configured for UDMA/100
ata2.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata2.01: 586072368 sectors, multi 0: LBA48
ata2.01: applying bridge limits
ata2.01: configured for UDMA/100
ata2.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata2.02: 586072368 sectors, multi 0: LBA48
ata2.02: applying bridge limits
ata2.02: configured for UDMA/100
ata2.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata2.03: 586072368 sectors, multi 0: LBA48
ata2.03: applying bridge limits
ata2.03: configured for UDMA/100
ata2.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata2.05: 640 sectors, multi 1: LBA
ata2.05: device is on DMA blacklist, disabling DMA
ata2.05: configured for PIO4
ata2: EH complete
scsi 2:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdf] 586072368 512-byte hardware sectors (300069 MB)
sd 2:0:0:0: [sdf] Write Protect is off
sd 2:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdf] 586072368 512-byte hardware sectors (300069 MB)
sd 2:0:0:0: [sdf] Write Protect is off
sd 2:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdf: sdf1
sd 2:0:0:0: [sdf] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg6 type 0
scsi 2:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 2:1:0:0: [sdg] 586072368 512-byte hardware sectors (300069 MB)
sd 2:1:0:0: [sdg] Write Protect is off
sd 2:1:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:1:0:0: [sdg] 586072368 512-byte hardware sectors (300069 MB)
sd 2:1:0:0: [sdg] Write Protect is off
sd 2:1:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdg: sdg1
sd 2:1:0:0: [sdg] Attached SCSI disk
sd 2:1:0:0: Attached scsi generic sg7 type 0
scsi 2:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 2:2:0:0: [sdh] 586072368 512-byte hardware sectors (300069 MB)
sd 2:2:0:0: [sdh] Write Protect is off
sd 2:2:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:2:0:0: [sdh] 586072368 512-byte hardware sectors (300069 MB)
sd 2:2:0:0: [sdh] Write Protect is off
sd 2:2:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdh: sdh1
sd 2:2:0:0: [sdh] Attached SCSI disk
sd 2:2:0:0: Attached scsi generic sg8 type 0
scsi 2:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 2:3:0:0: [sdi] 586072368 512-byte hardware sectors (300069 MB)
sd 2:3:0:0: [sdi] Write Protect is off
sd 2:3:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 2:3:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:3:0:0: [sdi] 586072368 512-byte hardware sectors (300069 MB)
sd 2:3:0:0: [sdi] Write Protect is off
sd 2:3:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 2:3:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdi: sdi1
sd 2:3:0:0: [sdi] Attached SCSI disk
sd 2:3:0:0: Attached scsi generic sg9 type 0
scsi 2:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 2:5:0:0: [sdj] 640 512-byte hardware sectors (0 MB)
sd 2:5:0:0: [sdj] Write Protect is off
sd 2:5:0:0: [sdj] Mode Sense: 00 3a 00 00
sd 2:5:0:0: [sdj] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:5:0:0: [sdj] 640 512-byte hardware sectors (0 MB)
sd 2:5:0:0: [sdj] Write Protect is off
sd 2:5:0:0: [sdj] Mode Sense: 00 3a 00 00
sd 2:5:0:0: [sdj] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdj: unknown partition table
sd 2:5:0:0: [sdj] Attached SCSI disk
sd 2:5:0:0: Attached scsi generic sg10 type 0
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: failed to recover PMP after 5 tries, giving up
ata1.15: Port Multiplier detaching
ata1.00: disabled
ata1.01: disabled
ata1.02: disabled
ata1.05: disabled
ata1.00: disabled
ata1: hard resetting link
ata1: SATA link down (SStatus 0 SControl 0)
ata1: EH complete
ata1.00: detaching (SCSI 1:0:0:0)
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
sd 1:0:0:0: [sdb] Stopping disk
sd 1:0:0:0: [sdb] START_STOP FAILED
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
ata1.01: detaching (SCSI 1:1:0:0)
sd 1:1:0:0: [sdc] Synchronizing SCSI cache
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
sd 1:1:0:0: [sdc] Stopping disk
sd 1:1:0:0: [sdc] START_STOP FAILED
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
ata1.02: detaching (SCSI 1:2:0:0)
sd 1:2:0:0: [sdd] Synchronizing SCSI cache
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
sd 1:2:0:0: [sdd] Stopping disk
sd 1:2:0:0: [sdd] START_STOP FAILED
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
ata1.05: detaching (SCSI 1:5:0:0)
sd 1:5:0:0: [sde] Stopping disk
sd 1:5:0:0: [sde] START_STOP FAILED
sd 1:5:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[-- Attachment #3: Bootlog12.txt --]
[-- Type: text/plain, Size: 30767 bytes --]
1:3:0:0: [sde] Synchronizing SCSI cache
sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
sd 1:3:0:0: [sde] Stopping disk
sd 1:3:0:0: [sde] START_STOP FAILED
sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata1.15: irq_stat 0x01940090, PHY RDY changed
ata1: SError: { 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 310)
ata1.05: hard resetting link
ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.00: revalidation failed (errno=-5)
ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.01: revalidation failed (errno=-5)
ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.02: revalidation failed (errno=-5)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdf] Write Protect is off
sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata1.15: irq_stat 0x01140010, PHY RDY changed
ata1: SError: { 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: failed to recover PMP after 5 tries, giving up
ata1.15: Port Multiplier detaching
ata1.00: disabled
ata1.01: disabled
ata1.02: disabled
ata1.05: disabled
ata1.00: disabled
ata1: hard resetting link
ata1: SATA link down (SStatus 1 SControl 0)
ata1: EH complete
ata1.00: detaching (SCSI 1:0:0:0)
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
sd 1:0:0:0: [sdb] Stopping disk
sd 1:0:0:0: [sdb] START_STOP FAILED
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
ata1.01: detaching (SCSI 1:1:0:0)
sd 1:1:0:0: [sdc] Synchronizing SCSI cache
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
sd 1:1:0:0: [sdc] Stopping disk
sd 1:1:0:0: [sdc] START_STOP FAILED
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
ata1.02: detaching (SCSI 1:2:0:0)
sd 1:2:0:0: [sdd] Synchronizing SCSI cache
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
sd 1:2:0:0: [sdd] Stopping disk
sd 1:2:0:0: [sdd] START_STOP FAILED
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
ata1.05: detaching (SCSI 1:5:0:0)
sd 1:5:0:0: [sdf] Stopping disk
sd 1:5:0:0: [sdf] START_STOP FAILED
sd 1:5:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata1: irq_stat 0x00a40080, device exchanged
ata1: SError: { PHYRdyChg }
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 320)
ata1.05: hard resetting link
ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata1.05: 640 sectors, multi 1: LBA
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.00: 586072368 sectors, multi 0: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.01: 586072368 sectors, multi 0: LBA48
ata1.01: applying bridge limits
ata1.01: configured for UDMA/100
ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.02: 586072368 sectors, multi 0: LBA48
ata1.02: applying bridge limits
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1: EH complete
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 1:1:0:0: [sdc] Attached SCSI disk
sd 1:1:0:0: Attached scsi generic sg3 type 0
scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:2:0:0: [sdd] Attached SCSI disk
sd 1:2:0:0: Attached scsi generic sg4 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sde] Write Protect is off
sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sde] Write Protect is off
sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sde: unknown partition table
sd 1:5:0:0: [sde] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg5 type 0
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xa frozen
ata1.15: irq_stat 0x01b40090, PHY RDY changed
ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: limiting SATA link speed to 1.5 Gbps
ata1.15: retrying hardreset in 5 secs
ata2: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata2: irq_stat 0x00a40080, device exchanged
ata2: SError: { PHYRdyChg }
ata2: hard resetting link
ata1.15: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata2.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata2.00: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata2.01: hard resetting link
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata2.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.02: hard resetting link
ata2.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.03: hard resetting link
ata2.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.04: hard resetting link
ata2.04: SATA link down (SStatus 0 SControl 320)
ata2.05: hard resetting link
ata2.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata2.06: hard resetting link
ata2.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata2.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata2.00: 586072368 sectors, multi 0: LBA48
ata2.00: applying bridge limits
ata2.00: configured for UDMA/100
ata2.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata2.01: 586072368 sectors, multi 0: LBA48
ata2.01: applying bridge limits
ata2.01: configured for UDMA/100
ata2.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata2.02: 586072368 sectors, multi 0: LBA48
ata2.02: applying bridge limits
ata2.02: configured for UDMA/100
ata2.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata2.03: 586072368 sectors, multi 0: LBA48
ata2.03: applying bridge limits
ata2.03: configured for UDMA/100
ata2.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata2.05: 640 sectors, multi 1: LBA
ata2.05: device is on DMA blacklist, disabling DMA
ata2.05: configured for PIO4
ata2: EH complete
scsi 2:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdf] 586072368 512-byte hardware sectors (300069 MB)
sd 2:0:0:0: [sdf] Write Protect is off
sd 2:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdf] 586072368 512-byte hardware sectors (300069 MB)
sd 2:0:0:0: [sdf] Write Protect is off
sd 2:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdf: sdf1
sd 2:0:0:0: [sdf] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg6 type 0
scsi 2:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 2:1:0:0: [sdg] 586072368 512-byte hardware sectors (300069 MB)
sd 2:1:0:0: [sdg] Write Protect is off
sd 2:1:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:1:0:0: [sdg] 586072368 512-byte hardware sectors (300069 MB)
sd 2:1:0:0: [sdg] Write Protect is off
sd 2:1:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdg: sdg1
sd 2:1:0:0: [sdg] Attached SCSI disk
sd 2:1:0:0: Attached scsi generic sg7 type 0
scsi 2:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 2:2:0:0: [sdh] 586072368 512-byte hardware sectors (300069 MB)
sd 2:2:0:0: [sdh] Write Protect is off
sd 2:2:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:2:0:0: [sdh] 586072368 512-byte hardware sectors (300069 MB)
sd 2:2:0:0: [sdh] Write Protect is off
sd 2:2:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdh: sdh1
sd 2:2:0:0: [sdh] Attached SCSI disk
sd 2:2:0:0: Attached scsi generic sg8 type 0
scsi 2:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 2:3:0:0: [sdi] 586072368 512-byte hardware sectors (300069 MB)
sd 2:3:0:0: [sdi] Write Protect is off
sd 2:3:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 2:3:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:3:0:0: [sdi] 586072368 512-byte hardware sectors (300069 MB)
sd 2:3:0:0: [sdi] Write Protect is off
sd 2:3:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 2:3:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdi: sdi1
sd 2:3:0:0: [sdi] Attached SCSI disk
sd 2:3:0:0: Attached scsi generic sg9 type 0
scsi 2:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 2:5:0:0: [sdj] 640 512-byte hardware sectors (0 MB)
sd 2:5:0:0: [sdj] Write Protect is off
sd 2:5:0:0: [sdj] Mode Sense: 00 3a 00 00
sd 2:5:0:0: [sdj] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:5:0:0: [sdj] 640 512-byte hardware sectors (0 MB)
sd 2:5:0:0: [sdj] Write Protect is off
sd 2:5:0:0: [sdj] Mode Sense: 00 3a 00 00
sd 2:5:0:0: [sdj] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdj: unknown partition table
sd 2:5:0:0: [sdj] Attached SCSI disk
sd 2:5:0:0: Attached scsi generic sg10 type 0
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: failed to recover PMP after 5 tries, giving up
ata1.15: Port Multiplier detaching
ata1.00: disabled
ata1.01: disabled
ata1.02: disabled
ata1.05: disabled
ata1.00: disabled
ata1: hard resetting link
ata1: SATA link down (SStatus 0 SControl 0)
ata1: EH complete
ata1.00: detaching (SCSI 1:0:0:0)
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
sd 1:0:0:0: [sdb] Stopping disk
sd 1:0:0:0: [sdb] START_STOP FAILED
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
ata1.01: detaching (SCSI 1:1:0:0)
sd 1:1:0:0: [sdc] Synchronizing SCSI cache
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
sd 1:1:0:0: [sdc] Stopping disk
sd 1:1:0:0: [sdc] START_STOP FAILED
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
ata1.02: detaching (SCSI 1:2:0:0)
sd 1:2:0:0: [sdd] Synchronizing SCSI cache
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
sd 1:2:0:0: [sdd] Stopping disk
sd 1:2:0:0: [sdd] START_STOP FAILED
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
ata1.05: detaching (SCSI 1:5:0:0)
sd 1:5:0:0: [sde] Stopping disk
sd 1:5:0:0: [sde] START_STOP FAILED
sd 1:5:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
ata2.00: failed to read SCR 1 (Emask=0x40)
ata2.01: failed to read SCR 1 (Emask=0x40)
ata2.02: failed to read SCR 1 (Emask=0x40)
ata2.03: failed to read SCR 1 (Emask=0x40)
ata2.04: failed to read SCR 1 (Emask=0x40)
ata2.05: failed to read SCR 1 (Emask=0x40)
ata2.06: failed to read SCR 1 (Emask=0x40)
ata2.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata2.15: irq_stat 0x01940090, PHY RDY changed
ata2: SError: { 10B8B }
ata2.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 0)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: retrying hardreset in 5 secs
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 0)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: limiting SATA link speed to 1.5 Gbps
ata2.15: retrying hardreset in 5 secs
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata1: irq_stat 0x00a40080, device exchanged
ata1: SError: { PHYRdyChg }
ata1: hard resetting link
ata2.15: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 10)
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: retrying hardreset in 5 secs
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 320)
ata1.05: hard resetting link
ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.00: 586072368 sectors, multi 0: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.01: 586072368 sectors, multi 0: LBA48
ata1.01: applying bridge limits
ata1.01: configured for UDMA/100
ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.02: 586072368 sectors, multi 0: LBA48
ata1.02: applying bridge limits
ata1.02: configured for UDMA/100
ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.03: 586072368 sectors, multi 0: LBA48
ata1.03: applying bridge limits
ata1.03: configured for UDMA/100
ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata1.05: 640 sectors, multi 1: LBA
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: EH complete
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 1:1:0:0: [sdc] Attached SCSI disk
sd 1:1:0:0: Attached scsi generic sg3 type 0
scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:2:0:0: [sdd] Attached SCSI disk
sd 1:2:0:0: Attached scsi generic sg4 type 0
scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 1:3:0:0: [sde] Attached SCSI disk
sd 1:3:0:0: Attached scsi generic sg5 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdk: unknown partition table
sd 1:5:0:0: [sdk] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg11 type 0
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 10)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: retrying hardreset in 5 secs
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 10)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: failed to recover PMP after 5 tries, giving up
ata2.15: Port Multiplier detaching
ata2.00: disabled
ata2.01: disabled
ata2.02: disabled
ata2.03: disabled
ata2.05: disabled
ata2.00: disabled
ata2: hard resetting link
ata2: SATA link down (SStatus 0 SControl 0)
ata2: EH complete
ata2.00: detaching (SCSI 2:0:0:0)
sd 2:0:0:0: [sdf] Synchronizing SCSI cache
sd 2:0:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
sd 2:0:0:0: [sdf] Stopping disk
sd 2:0:0:0: [sdf] START_STOP FAILED
sd 2:0:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
ata2.01: detaching (SCSI 2:1:0:0)
sd 2:1:0:0: [sdg] Synchronizing SCSI cache
sd 2:1:0:0: [sdg] Result: hostbyte=0x04 driverbyte=0x00
sd 2:1:0:0: [sdg] Stopping disk
sd 2:1:0:0: [sdg] START_STOP FAILED
sd 2:1:0:0: [sdg] Result: hostbyte=0x04 driverbyte=0x00
ata2.02: detaching (SCSI 2:2:0:0)
sd 2:2:0:0: [sdh] Synchronizing SCSI cache
sd 2:2:0:0: [sdh] Result: hostbyte=0x04 driverbyte=0x00
sd 2:2:0:0: [sdh] Stopping disk
sd 2:2:0:0: [sdh] START_STOP FAILED
sd 2:2:0:0: [sdh] Result: hostbyte=0x04 driverbyte=0x00
ata2.03: detaching (SCSI 2:3:0:0)
sd 2:3:0:0: [sdi] Synchronizing SCSI cache
sd 2:3:0:0: [sdi] Result: hostbyte=0x04 driverbyte=0x00
sd 2:3:0:0: [sdi] Stopping disk
sd 2:3:0:0: [sdi] START_STOP FAILED
sd 2:3:0:0: [sdi] Result: hostbyte=0x04 driverbyte=0x00
ata2.05: detaching (SCSI 2:5:0:0)
sd 2:5:0:0: [sdj] Stopping disk
sd 2:5:0:0: [sdj] START_STOP FAILED
sd 2:5:0:0: [sdj] Result: hostbyte=0x04 driverbyte=0x00
[-- Attachment #4: Bootlog13.txt --]
[-- Type: text/plain, Size: 30758 bytes --]
6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: failed to recover PMP after 5 tries, giving up
ata1.15: Port Multiplier detaching
ata1.00: disabled
ata1.01: disabled
ata1.02: disabled
ata1.05: disabled
ata1.00: disabled
ata1: hard resetting link
ata1: SATA link down (SStatus 1 SControl 0)
ata1: EH complete
ata1.00: detaching (SCSI 1:0:0:0)
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
sd 1:0:0:0: [sdb] Stopping disk
sd 1:0:0:0: [sdb] START_STOP FAILED
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
ata1.01: detaching (SCSI 1:1:0:0)
sd 1:1:0:0: [sdc] Synchronizing SCSI cache
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
sd 1:1:0:0: [sdc] Stopping disk
sd 1:1:0:0: [sdc] START_STOP FAILED
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
ata1.02: detaching (SCSI 1:2:0:0)
sd 1:2:0:0: [sdd] Synchronizing SCSI cache
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
sd 1:2:0:0: [sdd] Stopping disk
sd 1:2:0:0: [sdd] START_STOP FAILED
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
ata1.05: detaching (SCSI 1:5:0:0)
sd 1:5:0:0: [sdf] Stopping disk
sd 1:5:0:0: [sdf] START_STOP FAILED
sd 1:5:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata1: irq_stat 0x00a40080, device exchanged
ata1: SError: { PHYRdyChg }
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 320)
ata1.05: hard resetting link
ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata1.05: 640 sectors, multi 1: LBA
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.00: 586072368 sectors, multi 0: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.01: 586072368 sectors, multi 0: LBA48
ata1.01: applying bridge limits
ata1.01: configured for UDMA/100
ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.02: 586072368 sectors, multi 0: LBA48
ata1.02: applying bridge limits
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1: EH complete
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 1:1:0:0: [sdc] Attached SCSI disk
sd 1:1:0:0: Attached scsi generic sg3 type 0
scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:2:0:0: [sdd] Attached SCSI disk
sd 1:2:0:0: Attached scsi generic sg4 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sde] Write Protect is off
sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sde] Write Protect is off
sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sde: unknown partition table
sd 1:5:0:0: [sde] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg5 type 0
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xa frozen
ata1.15: irq_stat 0x01b40090, PHY RDY changed
ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: limiting SATA link speed to 1.5 Gbps
ata1.15: retrying hardreset in 5 secs
ata2: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata2: irq_stat 0x00a40080, device exchanged
ata2: SError: { PHYRdyChg }
ata2: hard resetting link
ata1.15: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata2.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata2.00: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata2.01: hard resetting link
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata2.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.02: hard resetting link
ata2.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.03: hard resetting link
ata2.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.04: hard resetting link
ata2.04: SATA link down (SStatus 0 SControl 320)
ata2.05: hard resetting link
ata2.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata2.06: hard resetting link
ata2.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata2.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata2.00: 586072368 sectors, multi 0: LBA48
ata2.00: applying bridge limits
ata2.00: configured for UDMA/100
ata2.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata2.01: 586072368 sectors, multi 0: LBA48
ata2.01: applying bridge limits
ata2.01: configured for UDMA/100
ata2.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata2.02: 586072368 sectors, multi 0: LBA48
ata2.02: applying bridge limits
ata2.02: configured for UDMA/100
ata2.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata2.03: 586072368 sectors, multi 0: LBA48
ata2.03: applying bridge limits
ata2.03: configured for UDMA/100
ata2.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata2.05: 640 sectors, multi 1: LBA
ata2.05: device is on DMA blacklist, disabling DMA
ata2.05: configured for PIO4
ata2: EH complete
scsi 2:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdf] 586072368 512-byte hardware sectors (300069 MB)
sd 2:0:0:0: [sdf] Write Protect is off
sd 2:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdf] 586072368 512-byte hardware sectors (300069 MB)
sd 2:0:0:0: [sdf] Write Protect is off
sd 2:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdf: sdf1
sd 2:0:0:0: [sdf] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg6 type 0
scsi 2:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 2:1:0:0: [sdg] 586072368 512-byte hardware sectors (300069 MB)
sd 2:1:0:0: [sdg] Write Protect is off
sd 2:1:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:1:0:0: [sdg] 586072368 512-byte hardware sectors (300069 MB)
sd 2:1:0:0: [sdg] Write Protect is off
sd 2:1:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdg: sdg1
sd 2:1:0:0: [sdg] Attached SCSI disk
sd 2:1:0:0: Attached scsi generic sg7 type 0
scsi 2:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 2:2:0:0: [sdh] 586072368 512-byte hardware sectors (300069 MB)
sd 2:2:0:0: [sdh] Write Protect is off
sd 2:2:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:2:0:0: [sdh] 586072368 512-byte hardware sectors (300069 MB)
sd 2:2:0:0: [sdh] Write Protect is off
sd 2:2:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdh: sdh1
sd 2:2:0:0: [sdh] Attached SCSI disk
sd 2:2:0:0: Attached scsi generic sg8 type 0
scsi 2:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 2:3:0:0: [sdi] 586072368 512-byte hardware sectors (300069 MB)
sd 2:3:0:0: [sdi] Write Protect is off
sd 2:3:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 2:3:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:3:0:0: [sdi] 586072368 512-byte hardware sectors (300069 MB)
sd 2:3:0:0: [sdi] Write Protect is off
sd 2:3:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 2:3:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdi: sdi1
sd 2:3:0:0: [sdi] Attached SCSI disk
sd 2:3:0:0: Attached scsi generic sg9 type 0
scsi 2:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 2:5:0:0: [sdj] 640 512-byte hardware sectors (0 MB)
sd 2:5:0:0: [sdj] Write Protect is off
sd 2:5:0:0: [sdj] Mode Sense: 00 3a 00 00
sd 2:5:0:0: [sdj] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:5:0:0: [sdj] 640 512-byte hardware sectors (0 MB)
sd 2:5:0:0: [sdj] Write Protect is off
sd 2:5:0:0: [sdj] Mode Sense: 00 3a 00 00
sd 2:5:0:0: [sdj] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdj: unknown partition table
sd 2:5:0:0: [sdj] Attached SCSI disk
sd 2:5:0:0: Attached scsi generic sg10 type 0
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: failed to recover PMP after 5 tries, giving up
ata1.15: Port Multiplier detaching
ata1.00: disabled
ata1.01: disabled
ata1.02: disabled
ata1.05: disabled
ata1.00: disabled
ata1: hard resetting link
ata1: SATA link down (SStatus 0 SControl 0)
ata1: EH complete
ata1.00: detaching (SCSI 1:0:0:0)
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
sd 1:0:0:0: [sdb] Stopping disk
sd 1:0:0:0: [sdb] START_STOP FAILED
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
ata1.01: detaching (SCSI 1:1:0:0)
sd 1:1:0:0: [sdc] Synchronizing SCSI cache
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
sd 1:1:0:0: [sdc] Stopping disk
sd 1:1:0:0: [sdc] START_STOP FAILED
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
ata1.02: detaching (SCSI 1:2:0:0)
sd 1:2:0:0: [sdd] Synchronizing SCSI cache
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
sd 1:2:0:0: [sdd] Stopping disk
sd 1:2:0:0: [sdd] START_STOP FAILED
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
ata1.05: detaching (SCSI 1:5:0:0)
sd 1:5:0:0: [sde] Stopping disk
sd 1:5:0:0: [sde] START_STOP FAILED
sd 1:5:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
ata2.00: failed to read SCR 1 (Emask=0x40)
ata2.01: failed to read SCR 1 (Emask=0x40)
ata2.02: failed to read SCR 1 (Emask=0x40)
ata2.03: failed to read SCR 1 (Emask=0x40)
ata2.04: failed to read SCR 1 (Emask=0x40)
ata2.05: failed to read SCR 1 (Emask=0x40)
ata2.06: failed to read SCR 1 (Emask=0x40)
ata2.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata2.15: irq_stat 0x01940090, PHY RDY changed
ata2: SError: { 10B8B }
ata2.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 0)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: retrying hardreset in 5 secs
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 0)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: limiting SATA link speed to 1.5 Gbps
ata2.15: retrying hardreset in 5 secs
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata1: irq_stat 0x00a40080, device exchanged
ata1: SError: { PHYRdyChg }
ata1: hard resetting link
ata2.15: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 10)
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: retrying hardreset in 5 secs
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 320)
ata1.05: hard resetting link
ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.00: 586072368 sectors, multi 0: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.01: 586072368 sectors, multi 0: LBA48
ata1.01: applying bridge limits
ata1.01: configured for UDMA/100
ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.02: 586072368 sectors, multi 0: LBA48
ata1.02: applying bridge limits
ata1.02: configured for UDMA/100
ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.03: 586072368 sectors, multi 0: LBA48
ata1.03: applying bridge limits
ata1.03: configured for UDMA/100
ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata1.05: 640 sectors, multi 1: LBA
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: EH complete
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 1:1:0:0: [sdc] Attached SCSI disk
sd 1:1:0:0: Attached scsi generic sg3 type 0
scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:2:0:0: [sdd] Attached SCSI disk
sd 1:2:0:0: Attached scsi generic sg4 type 0
scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 1:3:0:0: [sde] Attached SCSI disk
sd 1:3:0:0: Attached scsi generic sg5 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdk: unknown partition table
sd 1:5:0:0: [sdk] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg11 type 0
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 10)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: retrying hardreset in 5 secs
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 10)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: failed to recover PMP after 5 tries, giving up
ata2.15: Port Multiplier detaching
ata2.00: disabled
ata2.01: disabled
ata2.02: disabled
ata2.03: disabled
ata2.05: disabled
ata2.00: disabled
ata2: hard resetting link
ata2: SATA link down (SStatus 0 SControl 0)
ata2: EH complete
ata2.00: detaching (SCSI 2:0:0:0)
sd 2:0:0:0: [sdf] Synchronizing SCSI cache
sd 2:0:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
sd 2:0:0:0: [sdf] Stopping disk
sd 2:0:0:0: [sdf] START_STOP FAILED
sd 2:0:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
ata2.01: detaching (SCSI 2:1:0:0)
sd 2:1:0:0: [sdg] Synchronizing SCSI cache
sd 2:1:0:0: [sdg] Result: hostbyte=0x04 driverbyte=0x00
sd 2:1:0:0: [sdg] Stopping disk
sd 2:1:0:0: [sdg] START_STOP FAILED
sd 2:1:0:0: [sdg] Result: hostbyte=0x04 driverbyte=0x00
ata2.02: detaching (SCSI 2:2:0:0)
sd 2:2:0:0: [sdh] Synchronizing SCSI cache
sd 2:2:0:0: [sdh] Result: hostbyte=0x04 driverbyte=0x00
sd 2:2:0:0: [sdh] Stopping disk
sd 2:2:0:0: [sdh] START_STOP FAILED
sd 2:2:0:0: [sdh] Result: hostbyte=0x04 driverbyte=0x00
ata2.03: detaching (SCSI 2:3:0:0)
sd 2:3:0:0: [sdi] Synchronizing SCSI cache
sd 2:3:0:0: [sdi] Result: hostbyte=0x04 driverbyte=0x00
sd 2:3:0:0: [sdi] Stopping disk
sd 2:3:0:0: [sdi] START_STOP FAILED
sd 2:3:0:0: [sdi] Result: hostbyte=0x04 driverbyte=0x00
ata2.05: detaching (SCSI 2:5:0:0)
sd 2:5:0:0: [sdj] Stopping disk
sd 2:5:0:0: [sdj] START_STOP FAILED
sd 2:5:0:0: [sdj] Result: hostbyte=0x04 driverbyte=0x00
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata1.15: irq_stat 0x01140010, PHY RDY changed
ata1: SError: { 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: limiting SATA link speed to 1.5 Gbps
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 310)
ata1.05: hard resetting link
ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.00: revalidation failed (errno=-5)
ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.01: revalidation failed (errno=-5)
ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.02: revalidation failed (errno=-5)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1.03: disabled
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
ata1.03: detaching (SCSI 1:3:0:0)
sd 1:3:0:0: [sde] Synchronizing SCSI cache
sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
sd 1:3:0:0: [sde] Stopping disk
sd 1:3:0:0: [sde] START_STOP FAILED
sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[-- Attachment #5: Bootlog14.txt --]
[-- Type: text/plain, Size: 30815 bytes --]
1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1: EH complete
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 1:1:0:0: [sdc] Attached SCSI disk
sd 1:1:0:0: Attached scsi generic sg3 type 0
scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:2:0:0: [sdd] Attached SCSI disk
sd 1:2:0:0: Attached scsi generic sg4 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sde] Write Protect is off
sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sde] Write Protect is off
sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sde: unknown partition table
sd 1:5:0:0: [sde] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg5 type 0
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xa frozen
ata1.15: irq_stat 0x01b40090, PHY RDY changed
ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: limiting SATA link speed to 1.5 Gbps
ata1.15: retrying hardreset in 5 secs
ata2: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata2: irq_stat 0x00a40080, device exchanged
ata2: SError: { PHYRdyChg }
ata2: hard resetting link
ata1.15: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata2.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata2.00: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata2.01: hard resetting link
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata2.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.02: hard resetting link
ata2.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.03: hard resetting link
ata2.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.04: hard resetting link
ata2.04: SATA link down (SStatus 0 SControl 320)
ata2.05: hard resetting link
ata2.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata2.06: hard resetting link
ata2.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata2.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata2.00: 586072368 sectors, multi 0: LBA48
ata2.00: applying bridge limits
ata2.00: configured for UDMA/100
ata2.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata2.01: 586072368 sectors, multi 0: LBA48
ata2.01: applying bridge limits
ata2.01: configured for UDMA/100
ata2.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata2.02: 586072368 sectors, multi 0: LBA48
ata2.02: applying bridge limits
ata2.02: configured for UDMA/100
ata2.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata2.03: 586072368 sectors, multi 0: LBA48
ata2.03: applying bridge limits
ata2.03: configured for UDMA/100
ata2.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata2.05: 640 sectors, multi 1: LBA
ata2.05: device is on DMA blacklist, disabling DMA
ata2.05: configured for PIO4
ata2: EH complete
scsi 2:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdf] 586072368 512-byte hardware sectors (300069 MB)
sd 2:0:0:0: [sdf] Write Protect is off
sd 2:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdf] 586072368 512-byte hardware sectors (300069 MB)
sd 2:0:0:0: [sdf] Write Protect is off
sd 2:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdf: sdf1
sd 2:0:0:0: [sdf] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg6 type 0
scsi 2:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 2:1:0:0: [sdg] 586072368 512-byte hardware sectors (300069 MB)
sd 2:1:0:0: [sdg] Write Protect is off
sd 2:1:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:1:0:0: [sdg] 586072368 512-byte hardware sectors (300069 MB)
sd 2:1:0:0: [sdg] Write Protect is off
sd 2:1:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdg: sdg1
sd 2:1:0:0: [sdg] Attached SCSI disk
sd 2:1:0:0: Attached scsi generic sg7 type 0
scsi 2:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 2:2:0:0: [sdh] 586072368 512-byte hardware sectors (300069 MB)
sd 2:2:0:0: [sdh] Write Protect is off
sd 2:2:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:2:0:0: [sdh] 586072368 512-byte hardware sectors (300069 MB)
sd 2:2:0:0: [sdh] Write Protect is off
sd 2:2:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdh: sdh1
sd 2:2:0:0: [sdh] Attached SCSI disk
sd 2:2:0:0: Attached scsi generic sg8 type 0
scsi 2:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 2:3:0:0: [sdi] 586072368 512-byte hardware sectors (300069 MB)
sd 2:3:0:0: [sdi] Write Protect is off
sd 2:3:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 2:3:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:3:0:0: [sdi] 586072368 512-byte hardware sectors (300069 MB)
sd 2:3:0:0: [sdi] Write Protect is off
sd 2:3:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 2:3:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdi: sdi1
sd 2:3:0:0: [sdi] Attached SCSI disk
sd 2:3:0:0: Attached scsi generic sg9 type 0
scsi 2:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 2:5:0:0: [sdj] 640 512-byte hardware sectors (0 MB)
sd 2:5:0:0: [sdj] Write Protect is off
sd 2:5:0:0: [sdj] Mode Sense: 00 3a 00 00
sd 2:5:0:0: [sdj] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:5:0:0: [sdj] 640 512-byte hardware sectors (0 MB)
sd 2:5:0:0: [sdj] Write Protect is off
sd 2:5:0:0: [sdj] Mode Sense: 00 3a 00 00
sd 2:5:0:0: [sdj] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdj: unknown partition table
sd 2:5:0:0: [sdj] Attached SCSI disk
sd 2:5:0:0: Attached scsi generic sg10 type 0
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: failed to recover PMP after 5 tries, giving up
ata1.15: Port Multiplier detaching
ata1.00: disabled
ata1.01: disabled
ata1.02: disabled
ata1.05: disabled
ata1.00: disabled
ata1: hard resetting link
ata1: SATA link down (SStatus 0 SControl 0)
ata1: EH complete
ata1.00: detaching (SCSI 1:0:0:0)
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
sd 1:0:0:0: [sdb] Stopping disk
sd 1:0:0:0: [sdb] START_STOP FAILED
sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
ata1.01: detaching (SCSI 1:1:0:0)
sd 1:1:0:0: [sdc] Synchronizing SCSI cache
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
sd 1:1:0:0: [sdc] Stopping disk
sd 1:1:0:0: [sdc] START_STOP FAILED
sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
ata1.02: detaching (SCSI 1:2:0:0)
sd 1:2:0:0: [sdd] Synchronizing SCSI cache
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
sd 1:2:0:0: [sdd] Stopping disk
sd 1:2:0:0: [sdd] START_STOP FAILED
sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
ata1.05: detaching (SCSI 1:5:0:0)
sd 1:5:0:0: [sde] Stopping disk
sd 1:5:0:0: [sde] START_STOP FAILED
sd 1:5:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
ata2.00: failed to read SCR 1 (Emask=0x40)
ata2.01: failed to read SCR 1 (Emask=0x40)
ata2.02: failed to read SCR 1 (Emask=0x40)
ata2.03: failed to read SCR 1 (Emask=0x40)
ata2.04: failed to read SCR 1 (Emask=0x40)
ata2.05: failed to read SCR 1 (Emask=0x40)
ata2.06: failed to read SCR 1 (Emask=0x40)
ata2.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata2.15: irq_stat 0x01940090, PHY RDY changed
ata2: SError: { 10B8B }
ata2.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 0)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: retrying hardreset in 5 secs
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 0)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: limiting SATA link speed to 1.5 Gbps
ata2.15: retrying hardreset in 5 secs
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
ata1: irq_stat 0x00a40080, device exchanged
ata1: SError: { PHYRdyChg }
ata1: hard resetting link
ata2.15: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 10)
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: retrying hardreset in 5 secs
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 320)
ata1.05: hard resetting link
ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.00: 586072368 sectors, multi 0: LBA48
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata1.01: 586072368 sectors, multi 0: LBA48
ata1.01: applying bridge limits
ata1.01: configured for UDMA/100
ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.02: 586072368 sectors, multi 0: LBA48
ata1.02: applying bridge limits
ata1.02: configured for UDMA/100
ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.03: 586072368 sectors, multi 0: LBA48
ata1.03: applying bridge limits
ata1.03: configured for UDMA/100
ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
ata1.05: 640 sectors, multi 1: LBA
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: EH complete
scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg2 type 0
scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 1:1:0:0: [sdc] Attached SCSI disk
sd 1:1:0:0: Attached scsi generic sg3 type 0
scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:2:0:0: [sdd] Attached SCSI disk
sd 1:2:0:0: Attached scsi generic sg4 type 0
scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 1:3:0:0: [sde] Attached SCSI disk
sd 1:3:0:0: Attached scsi generic sg5 type 0
scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdk: unknown partition table
sd 1:5:0:0: [sdk] Attached SCSI disk
sd 1:5:0:0: Attached scsi generic sg11 type 0
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 10)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: retrying hardreset in 5 secs
ata2.15: hard resetting link
ata2.15: SATA link down (SStatus 0 SControl 10)
ata2.15: qc timeout (cmd 0xe4)
ata2.15: failed to read PMP GSCR[0] (Emask=0x4)
ata2.15: PMP revalidation failed (errno=-5)
ata2.15: failed to recover PMP after 5 tries, giving up
ata2.15: Port Multiplier detaching
ata2.00: disabled
ata2.01: disabled
ata2.02: disabled
ata2.03: disabled
ata2.05: disabled
ata2.00: disabled
ata2: hard resetting link
ata2: SATA link down (SStatus 0 SControl 0)
ata2: EH complete
ata2.00: detaching (SCSI 2:0:0:0)
sd 2:0:0:0: [sdf] Synchronizing SCSI cache
sd 2:0:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
sd 2:0:0:0: [sdf] Stopping disk
sd 2:0:0:0: [sdf] START_STOP FAILED
sd 2:0:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
ata2.01: detaching (SCSI 2:1:0:0)
sd 2:1:0:0: [sdg] Synchronizing SCSI cache
sd 2:1:0:0: [sdg] Result: hostbyte=0x04 driverbyte=0x00
sd 2:1:0:0: [sdg] Stopping disk
sd 2:1:0:0: [sdg] START_STOP FAILED
sd 2:1:0:0: [sdg] Result: hostbyte=0x04 driverbyte=0x00
ata2.02: detaching (SCSI 2:2:0:0)
sd 2:2:0:0: [sdh] Synchronizing SCSI cache
sd 2:2:0:0: [sdh] Result: hostbyte=0x04 driverbyte=0x00
sd 2:2:0:0: [sdh] Stopping disk
sd 2:2:0:0: [sdh] START_STOP FAILED
sd 2:2:0:0: [sdh] Result: hostbyte=0x04 driverbyte=0x00
ata2.03: detaching (SCSI 2:3:0:0)
sd 2:3:0:0: [sdi] Synchronizing SCSI cache
sd 2:3:0:0: [sdi] Result: hostbyte=0x04 driverbyte=0x00
sd 2:3:0:0: [sdi] Stopping disk
sd 2:3:0:0: [sdi] START_STOP FAILED
sd 2:3:0:0: [sdi] Result: hostbyte=0x04 driverbyte=0x00
ata2.05: detaching (SCSI 2:5:0:0)
sd 2:5:0:0: [sdj] Stopping disk
sd 2:5:0:0: [sdj] START_STOP FAILED
sd 2:5:0:0: [sdj] Result: hostbyte=0x04 driverbyte=0x00
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata1.15: irq_stat 0x01140010, PHY RDY changed
ata1: SError: { 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 1 SControl 0)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: limiting SATA link speed to 1.5 Gbps
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 310)
ata1.05: hard resetting link
ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.00: revalidation failed (errno=-5)
ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.01: revalidation failed (errno=-5)
ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.02: revalidation failed (errno=-5)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1.03: revalidation failed (errno=-5)
ata1.03: disabled
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata1: failed to recover some devices, retrying in 5 secs
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
ata1.03: detaching (SCSI 1:3:0:0)
sd 1:3:0:0: [sde] Synchronizing SCSI cache
sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
sd 1:3:0:0: [sde] Stopping disk
sd 1:3:0:0: [sde] START_STOP FAILED
sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
ata1.00: failed to read SCR 1 (Emask=0x40)
ata1.01: failed to read SCR 1 (Emask=0x40)
ata1.02: failed to read SCR 1 (Emask=0x40)
ata1.03: failed to read SCR 1 (Emask=0x40)
ata1.04: failed to read SCR 1 (Emask=0x40)
ata1.05: failed to read SCR 1 (Emask=0x40)
ata1.06: failed to read SCR 1 (Emask=0x40)
ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
ata1.15: irq_stat 0x01940090, PHY RDY changed
ata1: SError: { 10B8B }
ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link down (SStatus 0 SControl 10)
ata1.15: qc timeout (cmd 0xe4)
ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
ata1.15: PMP revalidation failed (errno=-5)
ata1.15: retrying hardreset in 5 secs
ata1.15: hard resetting link
ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
ata1.00: hard resetting link
ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.01: hard resetting link
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.02: hard resetting link
ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.03: hard resetting link
ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.04: hard resetting link
ata1.04: SATA link down (SStatus 0 SControl 310)
ata1.05: hard resetting link
ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata1.06: hard resetting link
ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata1.02: configured for UDMA/100
ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
ata1.03: 586072368 sectors, multi 0: LBA48
ata1.03: applying bridge limits
ata1.03: configured for UDMA/100
ata1.05: device is on DMA blacklist, disabling DMA
ata1.05: configured for PIO4
ata1: EH complete
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
sd 1:1:0:0: [sdc] Write Protect is off
sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
sd 1:2:0:0: [sdd] Write Protect is off
sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:5:0:0: [sdk] 640 512-byte hardware sectors (0 MB)
sd 1:5:0:0: [sdk] Write Protect is off
sd 1:5:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 1:5:0:0: [sdk] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
sd 1:3:0:0: [sde] Write Protect is off
sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 1:3:0:0: [sde] Attached SCSI disk
sd 1:3:0:0: Attached scsi generic sg5 type 0
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-09 17:47 ` Andrew Ryder
@ 2008-01-10 0:53 ` Tejun Heo
2008-01-10 1:58 ` Gaston, Jason D
0 siblings, 1 reply; 26+ messages in thread
From: Tejun Heo @ 2008-01-10 0:53 UTC (permalink / raw)
To: Andrew Ryder; +Cc: linux-ide
Hello, Andrew.
Andrew Ryder wrote:
> It works.
>
> Boot log is attached.
Great!
> I ran mke2fs on all 4 drives simultaneously and all is . I did notice
> that DMA was disabled on the hardware? Do you need any info from my side
> for this?
>
> Should device node sdf on the 5th port exist even though no drive is
> installed on the 5th port?
That's pseudo device for configuration. You can ignore it safely.
I'll forward the patch upstream after Gaston's response.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 26+ messages in thread
* RE: Sata 4726 Testing
2008-01-10 0:53 ` Tejun Heo
@ 2008-01-10 1:58 ` Gaston, Jason D
2008-01-10 3:19 ` Tejun Heo
0 siblings, 1 reply; 26+ messages in thread
From: Gaston, Jason D @ 2008-01-10 1:58 UTC (permalink / raw)
To: Tejun Heo, Andrew Ryder; +Cc: linux-ide
[-- Attachment #1: Type: text/plain, Size: 1356 bytes --]
>-----Original Message-----
>From: linux-ide-owner@vger.kernel.org [mailto:linux-ide-
>owner@vger.kernel.org] On Behalf Of Tejun Heo
>Sent: Wednesday, January 09, 2008 4:53 PM
>To: Andrew Ryder
>Cc: linux-ide@vger.kernel.org
>Subject: Re: Sata 4726 Testing
>
>Hello, Andrew.
>
>Andrew Ryder wrote:
>> It works.
>>
>> Boot log is attached.
>
>Great!
>
>> I ran mke2fs on all 4 drives simultaneously and all is . I did notice
>> that DMA was disabled on the hardware? Do you need any info from my
side
>> for this?
>>
>> Should device node sdf on the 5th port exist even though no drive is
>> installed on the 5th port?
>
>That's pseudo device for configuration. You can ignore it safely.
>
>I'll forward the patch upstream after Gaston's response.
>
>Thanks.
>
>--
>tejun
Attached are two dmesg outputs from 2.6.24-rc7 with only this simg quirk
patch applied.
The first (dmesg_wSipatch) was generated with the PMP turned off during
boot and then powered on, while connected to eSATA.
The second (dmesg_poweronoff) was generated with the PMP turned on and
connected to eSATA during boot. Then I turned the PMP off, let the
drives disappear from /sys/block/ and then turned on the PMP and let the
drives reappear in /sys/block/.
Please let me know if there is something else I can do.
Thanks,
Jason
[-- Attachment #2: dmesg_poweronoff.txt --]
[-- Type: text/plain, Size: 36801 bytes --]
Linux version 2.6.24-rc7_WSi_patch (root@localhost.localdomain) (gcc version 4.1.2 20070626 (Red Hat 4.1.2-14)) #2 SMP Wed Jan 9 18:37:46 PST 2008
Command line: ro root=/dev/VolGroup00/LogVol00 pci=nommconf rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d000 (usable)
BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003e7dd000 (usable)
BIOS-e820: 000000003e7dd000 - 000000003e81e000 (ACPI NVS)
BIOS-e820: 000000003e81e000 - 000000003e822000 (reserved)
BIOS-e820: 000000003e822000 - 000000003e879000 (ACPI NVS)
BIOS-e820: 000000003e879000 - 000000003ea28000 (reserved)
BIOS-e820: 000000003ea28000 - 000000003ea3c000 (ACPI NVS)
BIOS-e820: 000000003ea3c000 - 000000003efde000 (reserved)
BIOS-e820: 000000003efde000 - 000000003efed000 (ACPI NVS)
BIOS-e820: 000000003efed000 - 000000003f0d2000 (reserved)
BIOS-e820: 000000003f0d2000 - 000000003f114000 (ACPI data)
BIOS-e820: 000000003f114000 - 000000003f134000 (ACPI NVS)
BIOS-e820: 000000003f134000 - 000000003f136000 (reserved)
BIOS-e820: 000000003f136000 - 000000003f138000 (ACPI NVS)
BIOS-e820: 000000003f138000 - 000000003f4d0000 (reserved)
BIOS-e820: 000000003f4d0000 - 000000003f500000 (ACPI NVS)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
BIOS-e820: 00000000ffa80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000ffe80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 255965) 1 entries of 3200 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F03C0, 0024 (r2 AMI)
ACPI: XSDT 3F0D6E18, 004C (r1 AMI PILLARRK 6222004 MSFT 10013)
ACPI: FACP 3EFE0918, 00F4 (r4 AMI PILLARRK 6222004 MSFT 10013)
ACPI: DSDT 3EA28018, 98BA (r1 AMI PILLARRK 0 INTL 20060912)
ACPI: FACS 3F136E40, 0040
ACPI: APIC 3F0D2F18, 006C (r2 AMI PILLARRK 6222004 MSFT 10013)
ACPI: MCFG 3F131D18, 003C (r1 A M I GMCH945. 6222004 MSFT 97)
ACPI: SSDT 3EFDE918, 0425 (r1 TrmRef PtidDevc 1000 INTL 20060912)
ACPI: SSDT 3EFEC698, 05F9 (r1 PmRef CpuPm 3000 INTL 20060912)
No NUMA configuration found
Faking a node at 0000000000000000-000000003e7dd000
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 255965) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000003e7dd000
[ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
[ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
[ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
[ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
[ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0
[ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0
[ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 157
0: 256 -> 255965
On node 0 totalpages: 255866
DMA zone: 56 pages used for memmap
DMA zone: 1949 pages reserved
DMA zone: 1992 pages, LIFO batch:0
DMA32 zone: 3443 pages used for memmap
DMA32 zone: 248426 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3f500000:a0b00000)
SMP: Allowing 4 CPUs, 2 hotplug CPUs
PERCPU: Allocating 63928 bytes of per cpu data
Built 1 zonelists in Node order, mobility grouping on. Total pages: 250418
Policy zone: DMA32
Kernel command line: ro root=/dev/VolGroup00/LogVol00 pci=nommconf rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
time.c: Detected 2400.076 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
Memory: 997612k/1023860k available (2496k kernel code, 25852k reserved, 1183k data, 280k init)
Calibrating delay using timer specific routine.. 4805.15 BogoMIPS (lpj=2402575)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12500385
Detected 12.500 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.04 BogoMIPS (lpj=2400020)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz stepping 0a
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000001 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000002
domain 1: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
CPU1 attaching sched-domain:
domain 0: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000002 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000001
domain 1: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: ACPI Dock Station Driver
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: System BIOS is requesting _OSI(Linux)
ACPI: If "acpi_osi=Linux" works better,
Please send dmidecode to linux-acpi@vger.kernel.org
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: Power Resource [FN00] (off)
ACPI: Power Resource [FN01] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI-GART: No AMD northbridge found.
Time: tsc clocksource has been installed.
system 00:04: ioport range 0x680-0x69f has been reserved
system 00:04: ioport range 0x1000-0x100f has been reserved
system 00:04: ioport range 0xffff-0xffff has been reserved
system 00:04: ioport range 0xffff-0xffff has been reserved
system 00:04: ioport range 0x400-0x47f has been reserved
system 00:04: ioport range 0x500-0x53f has been reserved
system 00:04: ioport range 0x164e-0x164f has been reserved
system 00:05: ioport range 0x6a0-0x6af has been reserved
system 00:05: ioport range 0x6b0-0x6ef has been reserved
system 00:0b: iomem range 0xfed1c000-0xfed1ffff could not be reserved
system 00:0b: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:0b: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:0b: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:0b: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:0b: iomem range 0xfeb00000-0xfeb03fff has been reserved
system 00:0b: iomem range 0xfed45000-0xfed8ffff has been reserved
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3085k freed
audit: initializing netlink socket (disabled)
audit(1199904601.421:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN0] (off)
ACPI: Fan [FAN1] (off)
ACPI: SSDT 3EFEDA98, 02E9 (r1 PmRef Cpu0Ist 3000 INTL 20060912)
ACPI: SSDT 3EFF0618, 05B8 (r1 PmRef Cpu0Cst 3001 INTL 20060912)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 3EFEDE18, 01CF (r1 PmRef ApIst 3000 INTL 20060912)
ACPI: SSDT 3EFEEF18, 008D (r1 PmRef ApCst 3000 INTL 20060912)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI: Thermal Zone [TZ00] (27 C)
Marking TSC unstable due to possible TSC halt in C2
ACPI: Thermal Zone [TZ01] (27 C)
Time: acpi_pm clocksource has been installed.
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Clocksource tsc unstable (delta = -478207164 ns)
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
registered taskstats version 1
Freeing unused kernel memory: 280k freed
Write protecting the kernel read-only data: 868k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.0: irq 23, io base 0x000020a0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002080
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002060
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002040
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 19, io mem 0x50521c00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0x50521800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 8 ports detected
input: ImPS/2 Generic Wheel Mouse as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pmp pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0x50521000 port 0x50521100 irq 8415
ata2: SATA max UDMA/133 abar m2048@0x50521000 port 0x50521180 irq 8415
ata3: DUMMY
ata4: DUMMY
ata5: SATA max UDMA/133 abar m2048@0x50521000 port 0x50521300 irq 8415
ata6: SATA max UDMA/133 abar m2048@0x50521000 port 0x50521380 irq 8415
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 4 SControl 300)
ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.02: hard resetting link
ata6.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.03: hard resetting link
ata6.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.04: hard resetting link
ata6.04: SATA link down (SStatus 0 SControl 320)
ata6.05: hard resetting link
ata6.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
ata6.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.00: configured for UDMA/133
ata6.01: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata6.01: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.01: configured for UDMA/133
ata6.02: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata6.02: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.02: configured for UDMA/133
ata6.03: ATA-7: ST3120813AS, 3.AAE, max UDMA/133
ata6.03: 234441648 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.03: configured for UDMA/133
ata6: EH complete
scsi 0:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 5:0:0:0: Direct-Access ATA ST380815AS 3.AA PQ: 0 ANSI: 5
sd 5:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb:
sd 5:0:0:0: [sdb] Attached SCSI disk
scsi 5:1:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 5:1:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:1:0:0: [sdc] Write Protect is off
sd 5:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:1:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:1:0:0: [sdc] Write Protect is off
sd 5:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc:
sd 5:1:0:0: [sdc] Attached SCSI disk
scsi 5:2:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 5:2:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:2:0:0: [sdd] Write Protect is off
sd 5:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 5:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:2:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:2:0:0: [sdd] Write Protect is off
sd 5:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 5:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd:
sd 5:2:0:0: [sdd] Attached SCSI disk
scsi 5:3:0:0: Direct-Access ATA ST3120813AS 3.AA PQ: 0 ANSI: 5
sd 5:3:0:0: [sde] 234441648 512-byte hardware sectors (120034 MB)
sd 5:3:0:0: [sde] Write Protect is off
sd 5:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:3:0:0: [sde] 234441648 512-byte hardware sectors (120034 MB)
sd 5:3:0:0: [sde] Write Protect is off
sd 5:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde:
sd 5:3:0:0: [sde] Attached SCSI disk
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1199904615.096:2): enforcing=1 old_enforcing=0 auid=4294967295
SELinux:8192 avtab hash slots allocated.Num of rules:57675
SELinux:8192 avtab hash slots allocated.Num of rules:57675
security: 3 users, 6 roles, 1658 types, 210 bools, 1 sens, 1024 cats
security: 61 classes, 57675 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: policy loaded with handle_unknown=deny
audit(1199904615.364:3): policy loaded auid=4294967295
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input3
ACPI: Lid Switch [LID0]
input: Power Button (CM) as /class/input/input4
input: PC Speaker as /class/input/input5
ACPI: Power Button (CM) [PWRB]
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 19 (level, low) -> IRQ 19
ACPI: AC Adapter [ADP1] (on-line)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 5:0:0:0: Attached scsi generic sg1 type 0
sd 5:1:0:0: Attached scsi generic sg2 type 0
sd 5:2:0:0: Attached scsi generic sg3 type 0
sd 5:3:0:0: Attached scsi generic sg4 type 0
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Battery Slot [BAT2] (battery absent)
floppy0: no floppy controllers found
lp: driver loaded but no devices found
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
warning: process `kudzu' used the deprecated sysctl system call with 1.23.
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
audit(1199933436.562:4): audit_pid=2347 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x400001 action 0x3
ata6: SError: { RecovData Handshk }
ata6.00: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xb
ata6: SError: { PHYRdyChg DevExch }
ata6.02: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xb
ata6: SError: { PHYRdyChg DevExch }
ata6.03: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xb
ata6: SError: { PHYRdyChg DevExch }
ata6.15: hard resetting link
ata6.15: SATA link down (SStatus 0 SControl 300)
ata6.15: qc timeout (cmd 0xe4)
ata6.15: failed to read PMP GSCR[0] (Emask=0x4)
ata6.15: PMP revalidation failed (errno=-5)
ata6.15: retrying hardreset in 5 secs
ata6.15: hard resetting link
ata6.15: SATA link down (SStatus 0 SControl 300)
ata6.15: qc timeout (cmd 0xe4)
ata6.15: failed to read PMP GSCR[0] (Emask=0x4)
ata6.15: PMP revalidation failed (errno=-5)
ata6.15: limiting SATA link speed to 1.5 Gbps
ata6.15: retrying hardreset in 5 secs
ata6.15: hard resetting link
ata6.15: SATA link down (SStatus 0 SControl 310)
ata6.15: qc timeout (cmd 0xe4)
ata6.15: failed to read PMP GSCR[0] (Emask=0x4)
ata6.15: PMP revalidation failed (errno=-5)
ata6.15: retrying hardreset in 5 secs
ata6.15: hard resetting link
ata6.15: SATA link down (SStatus 0 SControl 310)
ata6.15: qc timeout (cmd 0xe4)
ata6.15: failed to read PMP GSCR[0] (Emask=0x4)
ata6.15: PMP revalidation failed (errno=-5)
ata6.15: retrying hardreset in 5 secs
ata6.15: hard resetting link
ata6.15: SATA link down (SStatus 0 SControl 310)
ata6.15: qc timeout (cmd 0xe4)
ata6.15: failed to read PMP GSCR[0] (Emask=0x4)
ata6.15: PMP revalidation failed (errno=-5)
ata6.15: failed to recover PMP after 5 tries, giving up
ata6.15: Port Multiplier detaching
ata6.00: disabled
ata6.01: disabled
ata6.02: disabled
ata6.03: disabled
ata6.00: disabled
ata6: hard resetting link
ata6: SATA link down (SStatus 0 SControl 310)
ata6: EH complete
ata6.00: detaching (SCSI 5:0:0:0)
sd 5:0:0:0: [sdb] Synchronizing SCSI cache
sd 5:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
sd 5:0:0:0: [sdb] Stopping disk
sd 5:0:0:0: [sdb] START_STOP FAILED
sd 5:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
ata6.01: detaching (SCSI 5:1:0:0)
sd 5:1:0:0: [sdc] Synchronizing SCSI cache
sd 5:1:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
sd 5:1:0:0: [sdc] Stopping disk
sd 5:1:0:0: [sdc] START_STOP FAILED
sd 5:1:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
ata6.02: detaching (SCSI 5:2:0:0)
sd 5:2:0:0: [sdd] Synchronizing SCSI cache
sd 5:2:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
sd 5:2:0:0: [sdd] Stopping disk
sd 5:2:0:0: [sdd] START_STOP FAILED
sd 5:2:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
ata6.03: detaching (SCSI 5:3:0:0)
sd 5:3:0:0: [sde] Synchronizing SCSI cache
sd 5:3:0:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
sd 5:3:0:0: [sde] Stopping disk
sd 5:3:0:0: [sde] START_STOP FAILED
sd 5:3:0:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
ata6: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xa frozen
ata6: irq_stat 0x00000040, connection status changed
ata6: SError: { CommWake DevExch }
ata6: hard resetting link
ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.03: hard resetting link
ata6.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.04: hard resetting link
ata6.04: SATA link down (SStatus 0 SControl 320)
ata6.05: hard resetting link
ata6.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
ata6.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.00: configured for UDMA/133
ata6.01: failed to IDENTIFY (I/O error, err_mask=0x100)
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.03: hard resetting link
ata6.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.04: hard resetting link
ata6.04: SATA link down (SStatus 0 SControl 320)
ata6.05: hard resetting link
ata6.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.00: configured for UDMA/133
ata6.01: failed to IDENTIFY (I/O error, err_mask=0x100)
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.03: hard resetting link
ata6.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.04: hard resetting link
ata6.04: SATA link down (SStatus 0 SControl 320)
ata6.05: hard resetting link
ata6.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.00: configured for UDMA/133
ata6.01: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata6.01: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.01: configured for UDMA/133
ata6.02: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata6.02: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.02: configured for UDMA/133
ata6.03: ATA-7: ST3120813AS, 3.AAE, max UDMA/133
ata6.03: 234441648 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.03: configured for UDMA/133
ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x1 t4
ata6.15: irq_stat 0x08000000, interface fatal error
ata6: EH complete
scsi 5:0:0:0: Direct-Access ATA ST380815AS 3.AA PQ: 0 ANSI: 5
sd 5:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb:
sd 5:0:0:0: [sdb] Attached SCSI disk
sd 5:0:0:0: Attached scsi generic sg1 type 0
scsi 5:1:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 5:1:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:1:0:0: [sdc] Write Protect is off
sd 5:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:1:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:1:0:0: [sdc] Write Protect is off
sd 5:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc:
sd 5:1:0:0: [sdc] Attached SCSI disk
sd 5:1:0:0: Attached scsi generic sg2 type 0
scsi 5:2:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 5:2:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:2:0:0: [sdd] Write Protect is off
sd 5:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 5:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:2:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:2:0:0: [sdd] Write Protect is off
sd 5:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 5:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd:
sd 5:2:0:0: [sdd] Attached SCSI disk
sd 5:2:0:0: Attached scsi generic sg3 type 0
scsi 5:3:0:0: Direct-Access ATA ST3120813AS 3.AA PQ: 0 ANSI: 5
sd 5:3:0:0: [sde] 234441648 512-byte hardware sectors (120034 MB)
sd 5:3:0:0: [sde] Write Protect is off
sd 5:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:3:0:0: [sde] 234441648 512-byte hardware sectors (120034 MB)
sd 5:3:0:0: [sde] Write Protect is off
sd 5:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde:
sd 5:3:0:0: [sde] Attached SCSI disk
sd 5:3:0:0: Attached scsi generic sg4 type 0
usb 8-1: new high speed USB device using ehci_hcd and address 2
usb 8-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 6:0:0:0: Direct-Access SanDisk U3 Titanium 2.18 PQ: 0 ANSI: 2
sd 6:0:0:0: [sdf] 4013713 512-byte hardware sectors (2055 MB)
sd 6:0:0:0: [sdf] Write Protect is off
sd 6:0:0:0: [sdf] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdf] Assuming drive cache: write through
sd 6:0:0:0: [sdf] 4013713 512-byte hardware sectors (2055 MB)
sd 6:0:0:0: [sdf] Write Protect is off
sd 6:0:0:0: [sdf] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdf] Assuming drive cache: write through
sdf: unknown partition table
sd 6:0:0:0: [sdf] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg5 type 0
usb-storage: device scan complete
SELinux: initialized (dev sdf, type vfat), uses genfs_contexts
[-- Attachment #3: dmesg_wSipatch.txt --]
[-- Type: text/plain, Size: 29939 bytes --]
Linux version 2.6.24-rc7_WSi_patch (root@localhost.localdomain) (gcc version 4.1.2 20070626 (Red Hat 4.1.2-14)) #2 SMP Wed Jan 9 18:37:46 PST 2008
Command line: ro root=/dev/VolGroup00/LogVol00 pci=nommconf rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d000 (usable)
BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003e7dd000 (usable)
BIOS-e820: 000000003e7dd000 - 000000003e81e000 (ACPI NVS)
BIOS-e820: 000000003e81e000 - 000000003e822000 (reserved)
BIOS-e820: 000000003e822000 - 000000003e879000 (ACPI NVS)
BIOS-e820: 000000003e879000 - 000000003ea28000 (reserved)
BIOS-e820: 000000003ea28000 - 000000003ea3c000 (ACPI NVS)
BIOS-e820: 000000003ea3c000 - 000000003efde000 (reserved)
BIOS-e820: 000000003efde000 - 000000003efed000 (ACPI NVS)
BIOS-e820: 000000003efed000 - 000000003f0d2000 (reserved)
BIOS-e820: 000000003f0d2000 - 000000003f114000 (ACPI data)
BIOS-e820: 000000003f114000 - 000000003f134000 (ACPI NVS)
BIOS-e820: 000000003f134000 - 000000003f136000 (reserved)
BIOS-e820: 000000003f136000 - 000000003f138000 (ACPI NVS)
BIOS-e820: 000000003f138000 - 000000003f4d0000 (reserved)
BIOS-e820: 000000003f4d0000 - 000000003f500000 (ACPI NVS)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
BIOS-e820: 00000000ffa80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000ffe80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 255965) 1 entries of 3200 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F03C0, 0024 (r2 AMI)
ACPI: XSDT 3F0D6E18, 004C (r1 AMI PILLARRK 6222004 MSFT 10013)
ACPI: FACP 3EFE0918, 00F4 (r4 AMI PILLARRK 6222004 MSFT 10013)
ACPI: DSDT 3EA28018, 98BA (r1 AMI PILLARRK 0 INTL 20060912)
ACPI: FACS 3F136E40, 0040
ACPI: APIC 3F0D2F18, 006C (r2 AMI PILLARRK 6222004 MSFT 10013)
ACPI: MCFG 3F131D18, 003C (r1 A M I GMCH945. 6222004 MSFT 97)
ACPI: SSDT 3EFDE918, 0425 (r1 TrmRef PtidDevc 1000 INTL 20060912)
ACPI: SSDT 3EFEC698, 05F9 (r1 PmRef CpuPm 3000 INTL 20060912)
No NUMA configuration found
Faking a node at 0000000000000000-000000003e7dd000
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 255965) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000003e7dd000
[ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
[ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
[ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
[ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
[ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0
[ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0
[ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 157
0: 256 -> 255965
On node 0 totalpages: 255866
DMA zone: 56 pages used for memmap
DMA zone: 1949 pages reserved
DMA zone: 1992 pages, LIFO batch:0
DMA32 zone: 3443 pages used for memmap
DMA32 zone: 248426 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3f500000:a0b00000)
SMP: Allowing 4 CPUs, 2 hotplug CPUs
PERCPU: Allocating 63928 bytes of per cpu data
Built 1 zonelists in Node order, mobility grouping on. Total pages: 250418
Policy zone: DMA32
Kernel command line: ro root=/dev/VolGroup00/LogVol00 pci=nommconf rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
time.c: Detected 2400.091 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
Memory: 997612k/1023860k available (2496k kernel code, 25852k reserved, 1183k data, 280k init)
Calibrating delay using timer specific routine.. 4804.42 BogoMIPS (lpj=2402213)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12500464
Detected 12.500 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.04 BogoMIPS (lpj=2400022)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz stepping 0a
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000001 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000002
domain 1: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
CPU1 attaching sched-domain:
domain 0: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000002 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000001
domain 1: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: ACPI Dock Station Driver
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: System BIOS is requesting _OSI(Linux)
ACPI: If "acpi_osi=Linux" works better,
Please send dmidecode to linux-acpi@vger.kernel.org
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: Power Resource [FN00] (off)
ACPI: Power Resource [FN01] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI-GART: No AMD northbridge found.
Time: tsc clocksource has been installed.
system 00:04: ioport range 0x680-0x69f has been reserved
system 00:04: ioport range 0x1000-0x100f has been reserved
system 00:04: ioport range 0xffff-0xffff has been reserved
system 00:04: ioport range 0xffff-0xffff has been reserved
system 00:04: ioport range 0x400-0x47f has been reserved
system 00:04: ioport range 0x500-0x53f has been reserved
system 00:04: ioport range 0x164e-0x164f has been reserved
system 00:05: ioport range 0x6a0-0x6af has been reserved
system 00:05: ioport range 0x6b0-0x6ef has been reserved
system 00:0b: iomem range 0xfed1c000-0xfed1ffff could not be reserved
system 00:0b: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:0b: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:0b: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:0b: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:0b: iomem range 0xfeb00000-0xfeb03fff has been reserved
system 00:0b: iomem range 0xfed45000-0xfed8ffff has been reserved
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3085k freed
audit: initializing netlink socket (disabled)
audit(1199904335.419:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN0] (off)
ACPI: Fan [FAN1] (off)
ACPI: SSDT 3EFEDA98, 02E9 (r1 PmRef Cpu0Ist 3000 INTL 20060912)
ACPI: SSDT 3EFF0618, 05B8 (r1 PmRef Cpu0Cst 3001 INTL 20060912)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 3EFEDE18, 01CF (r1 PmRef ApIst 3000 INTL 20060912)
ACPI: SSDT 3EFEEF18, 008D (r1 PmRef ApCst 3000 INTL 20060912)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI: Thermal Zone [TZ00] (27 C)
Marking TSC unstable due to possible TSC halt in C2
ACPI: Thermal Zone [TZ01] (27 C)
Time: acpi_pm clocksource has been installed.
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Clocksource tsc unstable (delta = -475640313 ns)
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
registered taskstats version 1
Freeing unused kernel memory: 280k freed
Write protecting the kernel read-only data: 868k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.0: irq 23, io base 0x000020a0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002080
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002060
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002040
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 19, io mem 0x50521c00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0x50521800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 8 ports detected
input: ImPS/2 Generic Wheel Mouse as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pmp pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0x50521000 port 0x50521100 irq 8415
ata2: SATA max UDMA/133 abar m2048@0x50521000 port 0x50521180 irq 8415
ata3: DUMMY
ata4: DUMMY
ata5: SATA max UDMA/133 abar m2048@0x50521000 port 0x50521300 irq 8415
ata6: SATA max UDMA/133 abar m2048@0x50521000 port 0x50521380 irq 8415
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 4 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1199904344.958:2): enforcing=1 old_enforcing=0 auid=4294967295
SELinux:8192 avtab hash slots allocated.Num of rules:57675
SELinux:8192 avtab hash slots allocated.Num of rules:57675
security: 3 users, 6 roles, 1658 types, 210 bools, 1 sens, 1024 cats
security: 61 classes, 57675 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: policy loaded with handle_unknown=deny
audit(1199904345.216:3): policy loaded auid=4294967295
input: PC Speaker as /class/input/input2
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input4
ACPI: Lid Switch [LID0]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PWRB]
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 19 (level, low) -> IRQ 19
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Battery Slot [BAT2] (battery absent)
sd 0:0:0:0: Attached scsi generic sg0 type 0
floppy0: no floppy controllers found
lp: driver loaded but no devices found
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
warning: process `kudzu' used the deprecated sysctl system call with 1.23.
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
audit(1199933166.078:4): audit_pid=2181 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
ata6: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xa frozen
ata6: irq_stat 0x00400040, connection status changed
ata6: SError: { PHYRdyChg CommWake DevExch }
ata6: hard resetting link
ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.03: hard resetting link
ata6.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.04: hard resetting link
ata6.04: SATA link down (SStatus 0 SControl 320)
ata6.05: hard resetting link
ata6.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.03: hard resetting link
ata6.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.04: hard resetting link
ata6.04: SATA link down (SStatus 0 SControl 320)
ata6.05: hard resetting link
ata6.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
ata6.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.00: configured for UDMA/133
ata6.01: failed to IDENTIFY (I/O error, err_mask=0x100)
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.03: hard resetting link
ata6.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.04: hard resetting link
ata6.04: SATA link down (SStatus 0 SControl 320)
ata6.05: hard resetting link
ata6.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.00: configured for UDMA/133
ata6.01: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata6.01: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.01: configured for UDMA/133
ata6.02: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata6.02: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.02: configured for UDMA/133
ata6.03: ATA-7: ST3120813AS, 3.AAE, max UDMA/133
ata6.03: 234441648 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.03: configured for UDMA/133
ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x1 t4
ata6.15: irq_stat 0x08000000, interface fatal error
ata6: EH complete
scsi 5:0:0:0: Direct-Access ATA ST380815AS 3.AA PQ: 0 ANSI: 5
sd 5:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb:
sd 5:0:0:0: [sdb] Attached SCSI disk
sd 5:0:0:0: Attached scsi generic sg1 type 0
scsi 5:1:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 5:1:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:1:0:0: [sdc] Write Protect is off
sd 5:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:1:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:1:0:0: [sdc] Write Protect is off
sd 5:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc:
sd 5:1:0:0: [sdc] Attached SCSI disk
sd 5:1:0:0: Attached scsi generic sg2 type 0
scsi 5:2:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 5:2:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:2:0:0: [sdd] Write Protect is off
sd 5:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 5:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:2:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:2:0:0: [sdd] Write Protect is off
sd 5:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 5:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd:
sd 5:2:0:0: [sdd] Attached SCSI disk
sd 5:2:0:0: Attached scsi generic sg3 type 0
scsi 5:3:0:0: Direct-Access ATA ST3120813AS 3.AA PQ: 0 ANSI: 5
sd 5:3:0:0: [sde] 234441648 512-byte hardware sectors (120034 MB)
sd 5:3:0:0: [sde] Write Protect is off
sd 5:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:3:0:0: [sde] 234441648 512-byte hardware sectors (120034 MB)
sd 5:3:0:0: [sde] Write Protect is off
sd 5:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde:
sd 5:3:0:0: [sde] Attached SCSI disk
sd 5:3:0:0: Attached scsi generic sg4 type 0
usb 8-1: new high speed USB device using ehci_hcd and address 2
usb 8-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 6:0:0:0: Direct-Access SanDisk U3 Titanium 2.18 PQ: 0 ANSI: 2
sd 6:0:0:0: [sdf] 4013713 512-byte hardware sectors (2055 MB)
sd 6:0:0:0: [sdf] Write Protect is off
sd 6:0:0:0: [sdf] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdf] Assuming drive cache: write through
sd 6:0:0:0: [sdf] 4013713 512-byte hardware sectors (2055 MB)
sd 6:0:0:0: [sdf] Write Protect is off
sd 6:0:0:0: [sdf] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdf] Assuming drive cache: write through
sdf: unknown partition table
sd 6:0:0:0: [sdf] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg5 type 0
usb-storage: device scan complete
SELinux: initialized (dev sdf, type vfat), uses genfs_contexts
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-10 1:58 ` Gaston, Jason D
@ 2008-01-10 3:19 ` Tejun Heo
2008-01-10 16:24 ` Gaston, Jason D
0 siblings, 1 reply; 26+ messages in thread
From: Tejun Heo @ 2008-01-10 3:19 UTC (permalink / raw)
To: Gaston, Jason D; +Cc: Andrew Ryder, linux-ide
Gaston, Jason D wrote:
> Attached are two dmesg outputs from 2.6.24-rc7 with only this simg quirk
> patch applied.
>
> The first (dmesg_wSipatch) was generated with the PMP turned off during
> boot and then powered on, while connected to eSATA.
>
> The second (dmesg_poweronoff) was generated with the PMP turned on and
> connected to eSATA during boot. Then I turned the PMP off, let the
> drives disappear from /sys/block/ and then turned on the PMP and let the
> drives reappear in /sys/block/.
>
> Please let me know if there is something else I can do.
Thanks for testing. It seems the errors you're seeing occur while the
drives are initializing. I'll look into that more but with or without
the patch, all the devices are detected and usable, right?
On 3726, the quirk patch has an unfortunate side effect of causing the
first DMA commands to timeout. I'll go and test 4726.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-09 5:45 ` Tejun Heo
2008-01-09 17:47 ` Andrew Ryder
@ 2008-01-10 3:29 ` Tejun Heo
2008-01-09 23:00 ` Andrew Ryder
1 sibling, 1 reply; 26+ messages in thread
From: Tejun Heo @ 2008-01-10 3:29 UTC (permalink / raw)
To: Andrew Ryder, Gaston, Jason D; +Cc: linux-ide
Tejun Heo wrote:
> Please apply the attached patch on top of 2.6.24-rc7 and report the
> result. Thanks.
Andrew, with the patch applied, please try to turn off and on the PMP
array while the system is running and verify that each time the array
gets detected correctly and disks are accessible.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-09 23:00 ` Andrew Ryder
@ 2008-01-10 4:20 ` Tejun Heo
2008-01-09 23:55 ` Andrew Ryder
0 siblings, 1 reply; 26+ messages in thread
From: Tejun Heo @ 2008-01-10 4:20 UTC (permalink / raw)
To: Andrew Ryder; +Cc: Gaston, Jason D, linux-ide
Andrew Ryder wrote:
> Tejun,
>
> I rebooted with the 4726 online during bootup, verified everything was
> there by re-formatting the fs on each drive. I powered off the 4726 for
> approx 15 seconds, turned it back on, and repeated the power on/off
> again about 1 minute later.
>
> The first 3 drives are accessible, but the 4th drive on ata1.03 failed
> to be recognized.
Hmmm... That's interesting. The fourth drive seemed to have gone out
for lunch. If you can, does connecting the drive to another port (be it
PMP port or not) without removing power make the drive work again? If
you can't do that, does removing the drive and re-plugging revives it?
Please try to determine who went out for lunch - the PMP port or the
drive. Also, can you please turn on CONFIG_PRINTK_TIME so that I can
tell what's happening when?
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-09 23:55 ` Andrew Ryder
@ 2008-01-10 6:36 ` Tejun Heo
2008-01-11 1:19 ` Andrew Ryder
0 siblings, 1 reply; 26+ messages in thread
From: Tejun Heo @ 2008-01-10 6:36 UTC (permalink / raw)
To: Andrew Ryder; +Cc: Gaston, Jason D, linux-ide
Hello,
Andrew Ryder wrote:
> This might be of interest.. I had turned the drive off for about 20
> minutes, then turned it back on. ata1.03 is now partially there, it is
> recognized as a device, but of 0MB in size.
>
> All of this is done with the 4726 turned on..
>
> Bootlog11.txt -> I unplugged the 4726, waited 10 seconds, and plugged it
> into the second port on the 3124. All 4 drives are there.
>
> Bootlog12.txt -> I unplugged the 4726 again, waited 10 seconds, plugged
> it back into the first (original) port, and ata1.03 is back..
>
> Bootlog13.txt -> I powered the 4726 off, waited 10 seconds, turned it
> back on. The same drive is missing now.
>
> Bootlog14.txt -> I unplugged, waited 10 seconds, and re-plugged the 4726
> into the same port (first eSATA port) and now ata1.03 is recognized and
> accessible.
>
> I'll make sure to turn on the timestamping for you tomorrow. Would want
> me to redo this testing so you can have the timestamps also?
Please swap the third and fourth drive and see whether the problem moves
with the drive or stays with the port. Also, please verify regular
powered on detection (array up and running before detection begins)
always works. 4726 is very quirky (it ate up a LOT of development /
testing time) and I guess we'll have to accept some brokenness.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 26+ messages in thread
* RE: Sata 4726 Testing
2008-01-10 3:19 ` Tejun Heo
@ 2008-01-10 16:24 ` Gaston, Jason D
0 siblings, 0 replies; 26+ messages in thread
From: Gaston, Jason D @ 2008-01-10 16:24 UTC (permalink / raw)
To: Tejun Heo; +Cc: Andrew Ryder, linux-ide
>-----Original Message-----
>From: linux-ide-owner@vger.kernel.org [mailto:linux-ide-
>owner@vger.kernel.org] On Behalf Of Tejun Heo
>Sent: Wednesday, January 09, 2008 7:19 PM
>To: Gaston, Jason D
>Cc: Andrew Ryder; linux-ide@vger.kernel.org
>Subject: Re: Sata 4726 Testing
>
>Gaston, Jason D wrote:
>> Attached are two dmesg outputs from 2.6.24-rc7 with only this simg
quirk
>> patch applied.
>>
>> The first (dmesg_wSipatch) was generated with the PMP turned off
during
>> boot and then powered on, while connected to eSATA.
>>
>> The second (dmesg_poweronoff) was generated with the PMP turned on
and
>> connected to eSATA during boot. Then I turned the PMP off, let the
>> drives disappear from /sys/block/ and then turned on the PMP and let
the
>> drives reappear in /sys/block/.
>>
>> Please let me know if there is something else I can do.
>
>Thanks for testing. It seems the errors you're seeing occur while the
>drives are initializing. I'll look into that more but with or without
>the patch, all the devices are detected and usable, right?
>
>On 3726, the quirk patch has an unfortunate side effect of causing the
>first DMA commands to timeout. I'll go and test 4726.
>
>Thanks.
>
>--
>tejun
Correct, with or without the patch, the drives are detected and usable.
Thanks,
Jason
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-10 6:36 ` Tejun Heo
@ 2008-01-11 1:19 ` Andrew Ryder
2008-01-11 7:49 ` Tejun Heo
0 siblings, 1 reply; 26+ messages in thread
From: Andrew Ryder @ 2008-01-11 1:19 UTC (permalink / raw)
To: Tejun Heo; +Cc: Gaston, Jason D, linux-ide
[-- Attachment #1: Type: text/plain, Size: 2148 bytes --]
For the regular power on detected, are you referring to cold/warm
booting the system and verifying initialization or only power cycling
the 4726?
Here are my test results, TestingRoutine.txt is the procedure I followed
and test results obtained. If I missed something, please let me know.
>From what I could find, the problem with ata1.03 not being detected is
consistent with the port. In my testing, I moved the last drive to the
5th port on the 4726 and the problem carried through. The issue seemed
to only occur when the 4726 was powered on/off, not when it was
unplugged and re-plugged with the power on.
If I have some time on the weekend, I will do a test routine of several
hot un-plugs / re-plugs of the 4726 and see what happens.
Thanks
Tejun Heo wrote:
> Hello,
>
> Andrew Ryder wrote:
>
>> This might be of interest.. I had turned the drive off for about 20
>> minutes, then turned it back on. ata1.03 is now partially there, it is
>> recognized as a device, but of 0MB in size.
>>
>> All of this is done with the 4726 turned on..
>>
>> Bootlog11.txt -> I unplugged the 4726, waited 10 seconds, and plugged it
>> into the second port on the 3124. All 4 drives are there.
>>
>> Bootlog12.txt -> I unplugged the 4726 again, waited 10 seconds, plugged
>> it back into the first (original) port, and ata1.03 is back..
>>
>> Bootlog13.txt -> I powered the 4726 off, waited 10 seconds, turned it
>> back on. The same drive is missing now.
>>
>> Bootlog14.txt -> I unplugged, waited 10 seconds, and re-plugged the 4726
>> into the same port (first eSATA port) and now ata1.03 is recognized and
>> accessible.
>>
>> I'll make sure to turn on the timestamping for you tomorrow. Would want
>> me to redo this testing so you can have the timestamps also?
>>
>
> Please swap the third and fourth drive and see whether the problem moves
> with the drive or stays with the port. Also, please verify regular
> powered on detection (array up and running before detection begins)
> always works. 4726 is very quirky (it ate up a LOT of development /
> testing time) and I guess we'll have to accept some brokenness.
>
> Thanks.
>
>
[-- Attachment #2: 1_Bootup.log --]
[-- Type: text/plain, Size: 27311 bytes --]
[ 0.000000] Linux version 2.6.24-rc7 (root@BigMouth) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #2 Thu Jan 10 12:53:51 EST 2008
[ 0.000000] Command line: root=/dev/sda3
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff30000 (usable)
[ 0.000000] BIOS-e820: 000000007ff30000 - 000000007ff40000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ff40000 - 000000007fff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 256, 524080) 1 entries of 256 used
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000FA850, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 7FF30000, 0030 (r1 A M I OEMRSDT 6000517 MSFT 97)
[ 0.000000] ACPI: FACP 7FF30200, 0081 (r1 A M I OEMFACP 6000517 MSFT 97)
[ 0.000000] ACPI: DSDT 7FF303F0, 38EA (r1 SK8V_ SK8V_033 33 MSFT 100000D)
[ 0.000000] ACPI: FACS 7FF40000, 0040
[ 0.000000] ACPI: APIC 7FF30390, 0052 (r1 A M I OEMAPIC 6000517 MSFT 97)
[ 0.000000] ACPI: OEMB 7FF40040, 003F (r1 A M I OEMBIOS 6000517 MSFT 97)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 256, 524080) 1 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 524080
[ 0.000000] On node 0 totalpages: 523983
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 964 pages reserved
[ 0.000000] DMA zone: 2979 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7109 pages used for memmap
[ 0.000000] DMA32 zone: 512875 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7ff80000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515854
[ 0.000000] Kernel command line: root=/dev/sda3
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] TSC calibrated against PM_TIMER
[ 40.969694] time.c: Detected 1802.299 MHz processor.
[ 40.972096] Console: colour VGA+ 80x25
[ 40.972100] console [tty0] enabled
[ 40.976164] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 40.978256] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 40.978631] Checking aperture...
[ 40.978685] CPU 0: aperture @ f8000000 size 64 MB
[ 40.998433] Memory: 2059876k/2096320k available (2288k kernel code, 35684k reserved, 1034k data, 192k init)
[ 41.075660] Calibrating delay using timer specific routine.. 3608.83 BogoMIPS (lpj=7217669)
[ 41.075816] Mount-cache hash table entries: 256
[ 41.075979] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 41.076037] CPU: L2 Cache: 1024K (64 bytes/line)
[ 41.076101] CPU: AMD Opteron(tm) Processor 144 stepping 0a
[ 41.076245] ACPI: Core revision 20070126
[ 41.118998] Using local APIC timer interrupts.
[ 41.174522] APIC timer calibration result 12515970
[ 41.174524] Detected 12.515 MHz APIC timer.
[ 41.174709] net_namespace: 120 bytes
[ 41.175136] NET: Registered protocol family 16
[ 41.175327] ACPI: bus type pci registered
[ 41.175387] PCI: Using configuration type 1
[ 41.177528] ACPI: EC: Look up EC in DSDT
[ 41.181044] ACPI: Interpreter enabled
[ 41.181097] ACPI: (supports S0 S1 S3 S5)
[ 41.181310] ACPI: Using IOAPIC for interrupt routing
[ 41.188091] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 41.188829] PCI: enabled onboard AC97/MC97 devices
[ 41.189130] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 41.195690] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
[ 41.196214] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
[ 41.196734] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
[ 41.197255] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
[ 41.197776] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.198382] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.199003] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.199610] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.200213] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 41.200290] pnp: PnP ACPI init
[ 41.200347] ACPI: bus type pnp registered
[ 41.203725] pnp: PnP ACPI: found 14 devices
[ 41.203778] ACPI: ACPI bus type pnp unregistered
[ 41.203979] SCSI subsystem initialized
[ 41.204120] PCI: Using ACPI for IRQ routing
[ 41.204175] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 41.204249] PCI: Cannot allocate resource region 0 of device 0000:00:00.0
[ 41.214633] agpgart: Detected AGP bridge 0
[ 41.218144] agpgart: AGP aperture is 64M @ 0xf8000000
[ 41.218581] Time: tsc clocksource has been installed.
[ 41.226616] system 00:09: ioport range 0x295-0x296 has been reserved
[ 41.226674] system 00:09: ioport range 0x3e1-0x3e7 has been reserved
[ 41.226731] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[ 41.226789] system 00:09: ioport range 0x800-0x87f has been reserved
[ 41.226846] system 00:09: ioport range 0x400-0x41f has been reserved
[ 41.226908] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[ 41.226966] system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 41.227034] system 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
[ 41.227107] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 41.227165] system 00:0d: iomem range 0xc0000-0xdffff has been reserved
[ 41.227222] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[ 41.227280] system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
[ 41.227348] system 00:0d: iomem range 0x0-0x0 could not be reserved
[ 41.227743] PCI: Bridge: 0000:00:01.0
[ 41.227796] IO window: a000-afff
[ 41.227850] MEM window: fc500000-fcafffff
[ 41.227905] PREFETCH window: b3e00000-f3dfffff
[ 41.227977] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 41.228001] NET: Registered protocol family 2
[ 41.262623] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 41.263229] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 41.265781] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 41.266183] TCP: Hash tables configured (established 262144 bind 65536)
[ 41.266240] TCP reno registered
[ 41.275236] audit: initializing netlink socket (disabled)
[ 41.275299] audit(1200010171.256:1): initialized
[ 41.275619] io scheduler noop registered
[ 41.275672] io scheduler anticipatory registered (default)
[ 41.275728] io scheduler deadline registered
[ 41.275788] io scheduler cfq registered
[ 41.275846] PCI: VIA PCI bridge detected. Disabling DAC.
[ 41.276369] Boot video device is 0000:01:00.0
[ 41.278423] Real Time Clock Driver v1.12ac
[ 41.278538] Linux agpgart interface v0.102
[ 41.278601] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 41.278762] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 41.278907] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 41.279557] RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
[ 41.279859] loop: module loaded
[ 41.279916] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 41.279973] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 41.280077] VIA8237SATA: IDE controller (0x1106:0x3149 rev 0x80) at PCI slot 0000:00:0f.0
[ 41.280160] ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
[ 41.280277] VIA8237SATA: 100% native mode on irq 20
[ 41.280335] ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
[ 41.280484] ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
[ 41.280631] Probing IDE interface ide2...
[ 41.846391] Probing IDE interface ide3...
[ 42.414221] VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
[ 42.414300] ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
[ 42.414408] VP_IDE: not 100% native mode: will probe irqs later
[ 42.414470] VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
[ 42.414540] ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
[ 42.414689] ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
[ 42.414835] Probing IDE interface ide0...
[ 42.830192] hdb: Maxtor 4G160J8, ATA DISK drive
[ 43.166089] hda: ST3200822A, ATA DISK drive
[ 43.166186] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 43.166420] hda: UDMA/100 mode selected
[ 43.166765] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 43.166873] hdb: UDMA/133 mode selected
[ 43.167065] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 43.167217] Probing IDE interface ide1...
[ 44.085810] hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
[ 44.869573] hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
[ 44.869745] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 44.869812] hdc: UDMA/33 mode selected
[ 44.869958] hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 44.870173] hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
[ 44.870241] hdd: UDMA/33 mode selected
[ 44.870547] ide1 at 0x170-0x177,0x376 on irq 15
[ 44.870782] Probing IDE interface ide2...
[ 45.437300] Probing IDE interface ide3...
[ 46.005149] hda: max request size: 512KiB
[ 46.005765] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
[ 46.006048] hda: cache flushes supported
[ 46.006124] hda: hda1 hda2
[ 46.014366] hdb: max request size: 512KiB
[ 46.021424] hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63
[ 46.021567] hdb: cache flushes not supported
[ 46.021636] hdb: hdb1
[ 46.039769] hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
[ 46.040052] Uniform CD-ROM driver Revision: 3.20
[ 47.333079] hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
[ 47.344447] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 52.555145] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 52.555148] <Adaptec 29160N Ultra160 SCSI adapter>
[ 52.555149] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
[ 52.555151]
[ 52.559077] scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
[ 52.559151] scsi0:A:0:0: Tagged Queuing enabled. Depth 32
[ 52.559250] target0:0:0: Beginning Domain Validation
[ 52.567382] target0:0:0: wide asynchronous
[ 52.573563] target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
[ 52.584331] target0:0:0: Ending Domain Validation
[ 53.106892] scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
[ 53.106967] target0:0:3: Beginning Domain Validation
[ 53.121395] target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
[ 53.129117] target0:0:3: Domain Validation skipping write tests
[ 53.129172] target0:0:3: Ending Domain Validation
[ 55.949167] Driver 'sd' needs updating - please use bus_type methods
[ 55.950059] sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
[ 55.951240] sd 0:0:0:0: [sda] Write Protect is off
[ 55.951295] sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
[ 55.952978] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 55.953844] sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
[ 55.955026] sd 0:0:0:0: [sda] Write Protect is off
[ 55.955080] sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
[ 55.956788] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 55.956857] sda: sda1 sda2 sda3
[ 55.964432] sd 0:0:0:0: [sda] Attached SCSI disk
[ 55.964494] Driver 'sr' needs updating - please use bus_type methods
[ 55.998683] sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
[ 55.998783] sr 0:0:3:0: Attached scsi CD-ROM sr0
[ 55.998850] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 55.999269] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 55.999325] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 55.999488] mice: PS/2 mouse device common for all mice
[ 56.029540] input: AT Translated Set 2 keyboard as /class/input/input0
[ 56.057155] TCP cubic registered
[ 56.057213] NET: Registered protocol family 1
[ 56.057277] NET: Registered protocol family 17
[ 56.057364] NET: Registered protocol family 33
[ 56.057557] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 56.453038] input: ImPS/2 Generic Wheel Mouse as /class/input/input1
[ 56.581620] ReiserFS: sda3: found reiserfs format "3.6" with standard journal
[ 56.581683] ReiserFS: sda3: using ordered data mode
[ 56.584649] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 56.586266] ReiserFS: sda3: checking transaction log (sda3)
[ 56.612710] ReiserFS: sda3: Using r5 hash to sort names
[ 56.612791] VFS: Mounted root (reiserfs filesystem) readonly.
[ 56.612861] Freeing unused kernel memory: 192k freed
[ 58.830733] libata version 3.00 loaded.
[ 58.834566] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 58.834589] sr 0:0:3:0: Attached scsi generic sg1 type 5
[ 58.835842] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 58.917293] usbcore: registered new interface driver usbfs
[ 58.917324] usbcore: registered new interface driver hub
[ 58.936252] usbcore: registered new device driver usb
[ 58.937137] USB Universal Host Controller Interface driver v3.0
[ 59.068441] input: Power Button (FF) as /class/input/input2
[ 59.113197] ACPI: Power Button (FF) [PWRF]
[ 59.113284] input: Power Button (CM) as /class/input/input3
[ 59.115827] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 59.143952] ACPI: Power Button (CM) [PWRB]
[ 59.144030] input: Sleep Button (CM) as /class/input/input4
[ 59.159999] sata_sil24 0000:00:0c.0: version 1.1
[ 59.160021] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 59.160374] PCI: Disallowing DAC for device 0000:00:0c.0
[ 59.169193] ACPI: Sleep Button (CM) [SLPB]
[ 59.174774] scsi1 : sata_sil24
[ 59.191103] scsi2 : sata_sil24
[ 59.205468] scsi3 : sata_sil24
[ 59.231501] scsi4 : sata_sil24
[ 59.231570] ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
[ 59.231574] ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
[ 59.231578] ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
[ 59.231581] ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
[ 59.880531] input: PC Speaker as /class/input/input5
[ 60.027104] Floppy drive(s): fd0 is 1.44M
[ 60.044905] FDC 0 is a post-1991 82077
[ 60.047130] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 60.047248] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 60.428849] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
[ 61.428460] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 61.428605] ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
[ 61.428797] ata1.00: hard resetting link
[ 61.748518] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 61.748524] ata1.01: hard resetting link
[ 62.068415] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.068418] ata1.02: hard resetting link
[ 62.388321] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.388323] ata1.03: hard resetting link
[ 62.708223] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.708226] ata1.04: hard resetting link
[ 63.028129] ata1.04: SATA link down (SStatus 0 SControl 320)
[ 63.028136] ata1.05: hard resetting link
[ 63.348026] ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 63.348029] ata1.06: hard resetting link
[ 63.667932] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 63.668978] ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 63.668981] ata1.00: 586072368 sectors, multi 16: LBA48
[ 63.668983] ata1.00: applying bridge limits
[ 63.670120] ata1.00: configured for UDMA/100
[ 63.671146] ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 63.671149] ata1.01: 586072368 sectors, multi 0: LBA48
[ 63.671151] ata1.01: applying bridge limits
[ 63.672287] ata1.01: configured for UDMA/100
[ 63.716356] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 63.716358] ata1.02: 586072368 sectors, multi 0: LBA48
[ 63.716360] ata1.02: applying bridge limits
[ 63.782803] ata1.02: configured for UDMA/100
[ 63.826318] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 63.826321] ata1.03: 586072368 sectors, multi 0: LBA48
[ 63.826323] ata1.03: applying bridge limits
[ 63.884593] ata1.03: configured for UDMA/100
[ 63.884662] ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
[ 63.884665] ata1.05: 640 sectors, multi 1: LBA
[ 63.884671] ata1.05: device is on DMA blacklist, disabling DMA
[ 63.884759] ata1.05: configured for PIO4
[ 63.884799] ata1: EH complete
[ 65.963083] ata2: SATA link down (SStatus 0 SControl 0)
[ 68.042452] ata3: SATA link down (SStatus 0 SControl 0)
[ 70.121822] ata4: SATA link down (SStatus 0 SControl 0)
[ 70.121936] scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.122351] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.122362] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.122365] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.122377] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.122423] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.122430] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.122432] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.122443] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.122448] sdb: sdb1
[ 70.125719] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 70.125755] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 70.126207] scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.126477] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.126485] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.126487] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.126499] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.126528] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.126535] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.126538] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.126549] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.126551] sdc: sdc1
[ 70.139869] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 70.139900] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 70.140370] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.140431] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.140439] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.140441] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.140452] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.140482] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.140489] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.140491] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.140502] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.140504] sdd: sdd1
[ 70.159621] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 70.159653] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 70.159699] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.159756] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.159764] sd 1:3:0:0: [sde] Write Protect is off
[ 70.159766] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.159777] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.160524] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.160532] sd 1:3:0:0: [sde] Write Protect is off
[ 70.160534] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.160545] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.160548] sde: sde1
[ 70.176524] sd 1:3:0:0: [sde] Attached SCSI disk
[ 70.176556] sd 1:3:0:0: Attached scsi generic sg5 type 0
[ 70.176602] scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 70.176661] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.176668] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.176670] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.176681] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.176710] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.176717] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.176719] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.176731] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.176733] sdf: unknown partition table
[ 70.177579] sd 1:5:0:0: [sdf] Attached SCSI disk
[ 70.177611] sd 1:5:0:0: Attached scsi generic sg6 type 0
[ 70.177788] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.177802] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 70.177992] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 70.178021] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
[ 70.178162] usb usb1: configuration #1 chosen from 1 choice
[ 70.178188] hub 1-0:1.0: USB hub found
[ 70.178196] hub 1-0:1.0: 2 ports detected
[ 70.281899] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.281913] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 70.281938] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 70.281961] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 70.282085] usb usb2: configuration #1 chosen from 1 choice
[ 70.282111] hub 2-0:1.0: USB hub found
[ 70.282119] hub 2-0:1.0: 2 ports detected
[ 70.385877] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 70.385890] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 70.385918] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 70.385941] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 70.386059] usb usb3: configuration #1 chosen from 1 choice
[ 70.386084] hub 3-0:1.0: USB hub found
[ 70.386091] hub 3-0:1.0: 2 ports detected
[ 70.489843] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 70.489857] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 70.489882] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 70.489905] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 70.490022] usb usb4: configuration #1 chosen from 1 choice
[ 70.490047] hub 4-0:1.0: USB hub found
[ 70.490055] hub 4-0:1.0: 2 ports detected
[ 70.593880] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 70.594063] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 70.594122] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 70.594171] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
[ 70.605694] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 70.605812] usb usb5: configuration #1 chosen from 1 choice
[ 70.605838] hub 5-0:1.0: USB hub found
[ 70.605847] hub 5-0:1.0: 8 ports detected
[ 70.709842] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 70.712088] Audigy2 value: Special config.
[ 72.299598] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 72.299603] Copyright (c) 1999-2006 Intel Corporation.
[ 72.299645] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 72.299650] PCI: Disallowing DAC for device 0000:00:0e.0
[ 72.558679] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 72.734178] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 72.890022] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 72.890034] ReiserFS: hdb1: using ordered data mode
[ 72.929121] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 72.930477] ReiserFS: hdb1: checking transaction log (hdb1)
[ 73.047880] ReiserFS: hdb1: Using r5 hash to sort names
[ 73.096394] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 73.096405] ReiserFS: hda2: using ordered data mode
[ 73.101224] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 73.102630] ReiserFS: hda2: checking transaction log (hda2)
[ 73.165531] ReiserFS: hda2: Using r5 hash to sort names
[ 79.014996] hda: UDMA/100 mode selected
[ 79.018892] hdb: UDMA/133 mode selected
[ 79.073585] hdc: UDMA/33 mode selected
[ 79.091357] hdd: UDMA/33 mode selected
[ 81.606735] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 85.836882] w83627hf: Found W83697HF chip at 0x290
[-- Attachment #3: 2_PowerOnOffTwice.log --]
[-- Type: text/plain, Size: 31304 bytes --]
55(auto-tune) selected PIO4
[ 43.166420] hda: UDMA/100 mode selected
[ 43.166765] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 43.166873] hdb: UDMA/133 mode selected
[ 43.167065] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 43.167217] Probing IDE interface ide1...
[ 44.085810] hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
[ 44.869573] hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
[ 44.869745] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 44.869812] hdc: UDMA/33 mode selected
[ 44.869958] hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 44.870173] hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
[ 44.870241] hdd: UDMA/33 mode selected
[ 44.870547] ide1 at 0x170-0x177,0x376 on irq 15
[ 44.870782] Probing IDE interface ide2...
[ 45.437300] Probing IDE interface ide3...
[ 46.005149] hda: max request size: 512KiB
[ 46.005765] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
[ 46.006048] hda: cache flushes supported
[ 46.006124] hda: hda1 hda2
[ 46.014366] hdb: max request size: 512KiB
[ 46.021424] hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63
[ 46.021567] hdb: cache flushes not supported
[ 46.021636] hdb: hdb1
[ 46.039769] hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
[ 46.040052] Uniform CD-ROM driver Revision: 3.20
[ 47.333079] hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
[ 47.344447] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 52.555145] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 52.555148] <Adaptec 29160N Ultra160 SCSI adapter>
[ 52.555149] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
[ 52.555151]
[ 52.559077] scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
[ 52.559151] scsi0:A:0:0: Tagged Queuing enabled. Depth 32
[ 52.559250] target0:0:0: Beginning Domain Validation
[ 52.567382] target0:0:0: wide asynchronous
[ 52.573563] target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
[ 52.584331] target0:0:0: Ending Domain Validation
[ 53.106892] scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
[ 53.106967] target0:0:3: Beginning Domain Validation
[ 53.121395] target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
[ 53.129117] target0:0:3: Domain Validation skipping write tests
[ 53.129172] target0:0:3: Ending Domain Validation
[ 55.949167] Driver 'sd' needs updating - please use bus_type methods
[ 55.950059] sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
[ 55.951240] sd 0:0:0:0: [sda] Write Protect is off
[ 55.951295] sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
[ 55.952978] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 55.953844] sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
[ 55.955026] sd 0:0:0:0: [sda] Write Protect is off
[ 55.955080] sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
[ 55.956788] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 55.956857] sda: sda1 sda2 sda3
[ 55.964432] sd 0:0:0:0: [sda] Attached SCSI disk
[ 55.964494] Driver 'sr' needs updating - please use bus_type methods
[ 55.998683] sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
[ 55.998783] sr 0:0:3:0: Attached scsi CD-ROM sr0
[ 55.998850] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 55.999269] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 55.999325] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 55.999488] mice: PS/2 mouse device common for all mice
[ 56.029540] input: AT Translated Set 2 keyboard as /class/input/input0
[ 56.057155] TCP cubic registered
[ 56.057213] NET: Registered protocol family 1
[ 56.057277] NET: Registered protocol family 17
[ 56.057364] NET: Registered protocol family 33
[ 56.057557] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 56.453038] input: ImPS/2 Generic Wheel Mouse as /class/input/input1
[ 56.581620] ReiserFS: sda3: found reiserfs format "3.6" with standard journal
[ 56.581683] ReiserFS: sda3: using ordered data mode
[ 56.584649] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 56.586266] ReiserFS: sda3: checking transaction log (sda3)
[ 56.612710] ReiserFS: sda3: Using r5 hash to sort names
[ 56.612791] VFS: Mounted root (reiserfs filesystem) readonly.
[ 56.612861] Freeing unused kernel memory: 192k freed
[ 58.830733] libata version 3.00 loaded.
[ 58.834566] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 58.834589] sr 0:0:3:0: Attached scsi generic sg1 type 5
[ 58.835842] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 58.917293] usbcore: registered new interface driver usbfs
[ 58.917324] usbcore: registered new interface driver hub
[ 58.936252] usbcore: registered new device driver usb
[ 58.937137] USB Universal Host Controller Interface driver v3.0
[ 59.068441] input: Power Button (FF) as /class/input/input2
[ 59.113197] ACPI: Power Button (FF) [PWRF]
[ 59.113284] input: Power Button (CM) as /class/input/input3
[ 59.115827] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 59.143952] ACPI: Power Button (CM) [PWRB]
[ 59.144030] input: Sleep Button (CM) as /class/input/input4
[ 59.159999] sata_sil24 0000:00:0c.0: version 1.1
[ 59.160021] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 59.160374] PCI: Disallowing DAC for device 0000:00:0c.0
[ 59.169193] ACPI: Sleep Button (CM) [SLPB]
[ 59.174774] scsi1 : sata_sil24
[ 59.191103] scsi2 : sata_sil24
[ 59.205468] scsi3 : sata_sil24
[ 59.231501] scsi4 : sata_sil24
[ 59.231570] ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
[ 59.231574] ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
[ 59.231578] ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
[ 59.231581] ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
[ 59.880531] input: PC Speaker as /class/input/input5
[ 60.027104] Floppy drive(s): fd0 is 1.44M
[ 60.044905] FDC 0 is a post-1991 82077
[ 60.047130] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 60.047248] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 60.428849] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
[ 61.428460] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 61.428605] ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
[ 61.428797] ata1.00: hard resetting link
[ 61.748518] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 61.748524] ata1.01: hard resetting link
[ 62.068415] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.068418] ata1.02: hard resetting link
[ 62.388321] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.388323] ata1.03: hard resetting link
[ 62.708223] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.708226] ata1.04: hard resetting link
[ 63.028129] ata1.04: SATA link down (SStatus 0 SControl 320)
[ 63.028136] ata1.05: hard resetting link
[ 63.348026] ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 63.348029] ata1.06: hard resetting link
[ 63.667932] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 63.668978] ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 63.668981] ata1.00: 586072368 sectors, multi 16: LBA48
[ 63.668983] ata1.00: applying bridge limits
[ 63.670120] ata1.00: configured for UDMA/100
[ 63.671146] ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 63.671149] ata1.01: 586072368 sectors, multi 0: LBA48
[ 63.671151] ata1.01: applying bridge limits
[ 63.672287] ata1.01: configured for UDMA/100
[ 63.716356] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 63.716358] ata1.02: 586072368 sectors, multi 0: LBA48
[ 63.716360] ata1.02: applying bridge limits
[ 63.782803] ata1.02: configured for UDMA/100
[ 63.826318] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 63.826321] ata1.03: 586072368 sectors, multi 0: LBA48
[ 63.826323] ata1.03: applying bridge limits
[ 63.884593] ata1.03: configured for UDMA/100
[ 63.884662] ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
[ 63.884665] ata1.05: 640 sectors, multi 1: LBA
[ 63.884671] ata1.05: device is on DMA blacklist, disabling DMA
[ 63.884759] ata1.05: configured for PIO4
[ 63.884799] ata1: EH complete
[ 65.963083] ata2: SATA link down (SStatus 0 SControl 0)
[ 68.042452] ata3: SATA link down (SStatus 0 SControl 0)
[ 70.121822] ata4: SATA link down (SStatus 0 SControl 0)
[ 70.121936] scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.122351] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.122362] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.122365] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.122377] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.122423] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.122430] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.122432] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.122443] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.122448] sdb: sdb1
[ 70.125719] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 70.125755] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 70.126207] scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.126477] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.126485] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.126487] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.126499] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.126528] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.126535] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.126538] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.126549] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.126551] sdc: sdc1
[ 70.139869] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 70.139900] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 70.140370] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.140431] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.140439] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.140441] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.140452] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.140482] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.140489] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.140491] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.140502] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.140504] sdd: sdd1
[ 70.159621] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 70.159653] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 70.159699] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.159756] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.159764] sd 1:3:0:0: [sde] Write Protect is off
[ 70.159766] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.159777] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.160524] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.160532] sd 1:3:0:0: [sde] Write Protect is off
[ 70.160534] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.160545] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.160548] sde: sde1
[ 70.176524] sd 1:3:0:0: [sde] Attached SCSI disk
[ 70.176556] sd 1:3:0:0: Attached scsi generic sg5 type 0
[ 70.176602] scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 70.176661] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.176668] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.176670] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.176681] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.176710] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.176717] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.176719] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.176731] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.176733] sdf: unknown partition table
[ 70.177579] sd 1:5:0:0: [sdf] Attached SCSI disk
[ 70.177611] sd 1:5:0:0: Attached scsi generic sg6 type 0
[ 70.177788] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.177802] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 70.177992] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 70.178021] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
[ 70.178162] usb usb1: configuration #1 chosen from 1 choice
[ 70.178188] hub 1-0:1.0: USB hub found
[ 70.178196] hub 1-0:1.0: 2 ports detected
[ 70.281899] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.281913] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 70.281938] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 70.281961] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 70.282085] usb usb2: configuration #1 chosen from 1 choice
[ 70.282111] hub 2-0:1.0: USB hub found
[ 70.282119] hub 2-0:1.0: 2 ports detected
[ 70.385877] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 70.385890] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 70.385918] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 70.385941] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 70.386059] usb usb3: configuration #1 chosen from 1 choice
[ 70.386084] hub 3-0:1.0: USB hub found
[ 70.386091] hub 3-0:1.0: 2 ports detected
[ 70.489843] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 70.489857] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 70.489882] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 70.489905] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 70.490022] usb usb4: configuration #1 chosen from 1 choice
[ 70.490047] hub 4-0:1.0: USB hub found
[ 70.490055] hub 4-0:1.0: 2 ports detected
[ 70.593880] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 70.594063] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 70.594122] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 70.594171] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
[ 70.605694] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 70.605812] usb usb5: configuration #1 chosen from 1 choice
[ 70.605838] hub 5-0:1.0: USB hub found
[ 70.605847] hub 5-0:1.0: 8 ports detected
[ 70.709842] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 70.712088] Audigy2 value: Special config.
[ 72.299598] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 72.299603] Copyright (c) 1999-2006 Intel Corporation.
[ 72.299645] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 72.299650] PCI: Disallowing DAC for device 0000:00:0e.0
[ 72.558679] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 72.734178] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 72.890022] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 72.890034] ReiserFS: hdb1: using ordered data mode
[ 72.929121] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 72.930477] ReiserFS: hdb1: checking transaction log (hdb1)
[ 73.047880] ReiserFS: hdb1: Using r5 hash to sort names
[ 73.096394] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 73.096405] ReiserFS: hda2: using ordered data mode
[ 73.101224] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 73.102630] ReiserFS: hda2: checking transaction log (hda2)
[ 73.165531] ReiserFS: hda2: Using r5 hash to sort names
[ 79.014996] hda: UDMA/100 mode selected
[ 79.018892] hdb: UDMA/133 mode selected
[ 79.073585] hdc: UDMA/33 mode selected
[ 79.091357] hdd: UDMA/33 mode selected
[ 81.606735] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 85.836882] w83627hf: Found W83697HF chip at 0x290
[ 209.524283] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 209.524288] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 209.524291] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 209.524294] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 209.524296] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 209.524299] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 209.524301] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 209.524305] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 209.524308] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 209.524311] ata1: SError: { 10B8B }
[ 209.524316] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524320] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524325] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524329] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524333] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524338] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524342] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524349] ata1.15: hard resetting link
[ 214.617980] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 214.869897] ata1.15: qc timeout (cmd 0xe4)
[ 214.869905] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 214.869908] ata1.15: PMP revalidation failed (errno=-5)
[ 214.869910] ata1.15: retrying hardreset in 5 secs
[ 219.872379] ata1.15: hard resetting link
[ 224.966839] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 225.173188] ata1.15: failed to read PMP GSCR[0] (Emask=0x100)
[ 225.173191] ata1.15: PMP revalidation failed (errno=-5)
[ 225.173194] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 225.173197] ata1.15: retrying hardreset in 5 secs
[ 230.173255] ata1.15: hard resetting link
[ 232.372597] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 232.372805] ata1.00: hard resetting link
[ 232.692677] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 232.692680] ata1.01: hard resetting link
[ 233.012579] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 233.012583] ata1.02: hard resetting link
[ 233.332482] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 233.332485] ata1.03: hard resetting link
[ 233.652385] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 233.652388] ata1.04: hard resetting link
[ 233.972289] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 233.972292] ata1.05: hard resetting link
[ 234.292189] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 234.292192] ata1.06: hard resetting link
[ 234.612092] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 234.614276] ata1.00: configured for UDMA/100
[ 234.616463] ata1.01: configured for UDMA/100
[ 234.719921] ata1.02: configured for UDMA/100
[ 234.821531] ata1.03: configured for UDMA/100
[ 234.821636] ata1.05: device is on DMA blacklist, disabling DMA
[ 234.821741] ata1.05: configured for PIO4
[ 234.821953] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
[ 234.821956] ata1.15: irq_stat 0x00800080, device exchanged
[ 234.822220] ata1: EH complete
[ 234.822245] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822256] sd 1:0:0:0: [sdb] Write Protect is off
[ 234.822259] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 234.822271] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822285] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822292] sd 1:1:0:0: [sdc] Write Protect is off
[ 234.822295] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 234.822305] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822318] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822325] sd 1:2:0:0: [sdd] Write Protect is off
[ 234.822328] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 234.822339] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822353] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822361] sd 1:3:0:0: [sde] Write Protect is off
[ 234.822363] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 234.822375] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822388] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 234.822396] sd 1:5:0:0: [sdf] Write Protect is off
[ 234.822399] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 234.822410] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822423] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822431] sd 1:0:0:0: [sdb] Write Protect is off
[ 234.822434] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 234.822445] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822458] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822465] sd 1:1:0:0: [sdc] Write Protect is off
[ 234.822468] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 234.822479] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822492] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822500] sd 1:2:0:0: [sdd] Write Protect is off
[ 234.822503] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 234.822514] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822527] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822534] sd 1:3:0:0: [sde] Write Protect is off
[ 234.822537] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 234.822549] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822561] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 234.822569] sd 1:5:0:0: [sdf] Write Protect is off
[ 234.822571] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 234.822583] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 396.287513] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 396.287519] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 396.287522] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 396.287525] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 396.287528] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 396.287531] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 396.287534] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 396.287539] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 396.287542] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 396.287546] ata1: SError: { 10B8B }
[ 396.287551] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287557] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287562] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287567] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287572] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287577] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287582] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287590] ata1.15: hard resetting link
[ 401.381322] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 401.633240] ata1.15: qc timeout (cmd 0xe4)
[ 401.633248] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 401.633251] ata1.15: PMP revalidation failed (errno=-5)
[ 401.633254] ata1.15: retrying hardreset in 5 secs
[ 406.635722] ata1.15: hard resetting link
[ 411.730181] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 411.982099] ata1.15: qc timeout (cmd 0xe4)
[ 411.982107] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 411.982110] ata1.15: PMP revalidation failed (errno=-5)
[ 411.982113] ata1.15: retrying hardreset in 5 secs
[ 416.984582] ata1.15: hard resetting link
[ 419.183924] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 419.184128] ata1.00: hard resetting link
[ 419.504005] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 419.504009] ata1.01: hard resetting link
[ 419.823907] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 419.823911] ata1.02: hard resetting link
[ 420.143811] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 420.143815] ata1.03: hard resetting link
[ 420.463713] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 420.463717] ata1.04: hard resetting link
[ 420.783616] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 420.783619] ata1.05: hard resetting link
[ 421.103516] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 421.103520] ata1.06: hard resetting link
[ 421.423426] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 421.423538] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423542] ata1.00: revalidation failed (errno=-5)
[ 421.423672] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423675] ata1.01: revalidation failed (errno=-5)
[ 421.423804] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423808] ata1.02: revalidation failed (errno=-5)
[ 421.423936] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423940] ata1.03: revalidation failed (errno=-5)
[ 421.424077] ata1.05: device is on DMA blacklist, disabling DMA
[ 421.424192] ata1.05: configured for PIO4
[ 421.424195] ata1: failed to recover some devices, retrying in 5 secs
[ 426.425719] ata1.00: hard resetting link
[ 426.745807] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 426.745811] ata1.01: hard resetting link
[ 427.065709] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 427.065713] ata1.02: hard resetting link
[ 427.385613] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 427.385617] ata1.03: hard resetting link
[ 427.705517] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 427.707726] ata1.00: configured for UDMA/100
[ 427.709957] ata1.01: configured for UDMA/100
[ 427.813721] ata1.02: configured for UDMA/100
[ 427.813822] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 427.813826] ata1.03: revalidation failed (errno=-5)
[ 427.813829] ata1: failed to recover some devices, retrying in 5 secs
[ 432.815779] ata1.03: hard resetting link
[ 433.135867] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 433.135974] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 433.135977] ata1.03: revalidation failed (errno=-5)
[ 433.135980] ata1.03: disabled
[ 433.639529] ata1.03: hard resetting link
[ 433.959617] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 433.959672] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 433.959676] ata1: failed to recover some devices, retrying in 5 secs
[ 438.961914] ata1.03: hard resetting link
[ 439.282004] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 439.282059] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 439.282062] ata1: failed to recover some devices, retrying in 5 secs
[ 444.284300] ata1.03: hard resetting link
[ 444.604390] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 444.604446] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 444.604450] ata1: failed to recover some devices, retrying in 5 secs
[ 449.606691] ata1.03: hard resetting link
[ 449.926776] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 449.927130] ata1: EH complete
[ 449.927174] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927186] sd 1:0:0:0: [sdb] Write Protect is off
[ 449.927189] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 449.927202] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927218] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927226] sd 1:1:0:0: [sdc] Write Protect is off
[ 449.927229] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 449.927240] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927254] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927262] sd 1:2:0:0: [sdd] Write Protect is off
[ 449.927264] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 449.927276] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927289] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 449.927297] sd 1:5:0:0: [sdf] Write Protect is off
[ 449.927299] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 449.927395] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927408] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927416] sd 1:0:0:0: [sdb] Write Protect is off
[ 449.927419] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 449.927430] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927442] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927450] sd 1:1:0:0: [sdc] Write Protect is off
[ 449.927453] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 449.927464] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927477] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927484] sd 1:2:0:0: [sdd] Write Protect is off
[ 449.927487] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 449.927498] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927511] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 449.927518] sd 1:5:0:0: [sdf] Write Protect is off
[ 449.927521] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 449.927532] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927538] ata1.03: detaching (SCSI 1:3:0:0)
[ 449.927717] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 449.928940] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 449.928945] sd 1:3:0:0: [sde] Stopping disk
[ 449.928950] sd 1:3:0:0: [sde] START_STOP FAILED
[ 449.928953] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[-- Attachment #4: 3_PlugUnplug.txt --]
[-- Type: text/plain, Size: 31316 bytes --]
f8 (irq = 3) is a 16550A
[ 60.047248] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 60.428849] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
[ 61.428460] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 61.428605] ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
[ 61.428797] ata1.00: hard resetting link
[ 61.748518] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 61.748524] ata1.01: hard resetting link
[ 62.068415] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.068418] ata1.02: hard resetting link
[ 62.388321] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.388323] ata1.03: hard resetting link
[ 62.708223] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.708226] ata1.04: hard resetting link
[ 63.028129] ata1.04: SATA link down (SStatus 0 SControl 320)
[ 63.028136] ata1.05: hard resetting link
[ 63.348026] ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 63.348029] ata1.06: hard resetting link
[ 63.667932] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 63.668978] ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 63.668981] ata1.00: 586072368 sectors, multi 16: LBA48
[ 63.668983] ata1.00: applying bridge limits
[ 63.670120] ata1.00: configured for UDMA/100
[ 63.671146] ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 63.671149] ata1.01: 586072368 sectors, multi 0: LBA48
[ 63.671151] ata1.01: applying bridge limits
[ 63.672287] ata1.01: configured for UDMA/100
[ 63.716356] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 63.716358] ata1.02: 586072368 sectors, multi 0: LBA48
[ 63.716360] ata1.02: applying bridge limits
[ 63.782803] ata1.02: configured for UDMA/100
[ 63.826318] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 63.826321] ata1.03: 586072368 sectors, multi 0: LBA48
[ 63.826323] ata1.03: applying bridge limits
[ 63.884593] ata1.03: configured for UDMA/100
[ 63.884662] ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
[ 63.884665] ata1.05: 640 sectors, multi 1: LBA
[ 63.884671] ata1.05: device is on DMA blacklist, disabling DMA
[ 63.884759] ata1.05: configured for PIO4
[ 63.884799] ata1: EH complete
[ 65.963083] ata2: SATA link down (SStatus 0 SControl 0)
[ 68.042452] ata3: SATA link down (SStatus 0 SControl 0)
[ 70.121822] ata4: SATA link down (SStatus 0 SControl 0)
[ 70.121936] scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.122351] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.122362] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.122365] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.122377] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.122423] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.122430] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.122432] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.122443] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.122448] sdb: sdb1
[ 70.125719] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 70.125755] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 70.126207] scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.126477] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.126485] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.126487] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.126499] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.126528] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.126535] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.126538] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.126549] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.126551] sdc: sdc1
[ 70.139869] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 70.139900] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 70.140370] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.140431] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.140439] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.140441] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.140452] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.140482] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.140489] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.140491] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.140502] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.140504] sdd: sdd1
[ 70.159621] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 70.159653] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 70.159699] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.159756] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.159764] sd 1:3:0:0: [sde] Write Protect is off
[ 70.159766] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.159777] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.160524] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.160532] sd 1:3:0:0: [sde] Write Protect is off
[ 70.160534] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.160545] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.160548] sde: sde1
[ 70.176524] sd 1:3:0:0: [sde] Attached SCSI disk
[ 70.176556] sd 1:3:0:0: Attached scsi generic sg5 type 0
[ 70.176602] scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 70.176661] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.176668] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.176670] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.176681] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.176710] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.176717] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.176719] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.176731] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.176733] sdf: unknown partition table
[ 70.177579] sd 1:5:0:0: [sdf] Attached SCSI disk
[ 70.177611] sd 1:5:0:0: Attached scsi generic sg6 type 0
[ 70.177788] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.177802] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 70.177992] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 70.178021] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
[ 70.178162] usb usb1: configuration #1 chosen from 1 choice
[ 70.178188] hub 1-0:1.0: USB hub found
[ 70.178196] hub 1-0:1.0: 2 ports detected
[ 70.281899] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.281913] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 70.281938] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 70.281961] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 70.282085] usb usb2: configuration #1 chosen from 1 choice
[ 70.282111] hub 2-0:1.0: USB hub found
[ 70.282119] hub 2-0:1.0: 2 ports detected
[ 70.385877] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 70.385890] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 70.385918] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 70.385941] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 70.386059] usb usb3: configuration #1 chosen from 1 choice
[ 70.386084] hub 3-0:1.0: USB hub found
[ 70.386091] hub 3-0:1.0: 2 ports detected
[ 70.489843] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 70.489857] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 70.489882] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 70.489905] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 70.490022] usb usb4: configuration #1 chosen from 1 choice
[ 70.490047] hub 4-0:1.0: USB hub found
[ 70.490055] hub 4-0:1.0: 2 ports detected
[ 70.593880] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 70.594063] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 70.594122] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 70.594171] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
[ 70.605694] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 70.605812] usb usb5: configuration #1 chosen from 1 choice
[ 70.605838] hub 5-0:1.0: USB hub found
[ 70.605847] hub 5-0:1.0: 8 ports detected
[ 70.709842] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 70.712088] Audigy2 value: Special config.
[ 72.299598] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 72.299603] Copyright (c) 1999-2006 Intel Corporation.
[ 72.299645] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 72.299650] PCI: Disallowing DAC for device 0000:00:0e.0
[ 72.558679] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 72.734178] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 72.890022] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 72.890034] ReiserFS: hdb1: using ordered data mode
[ 72.929121] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 72.930477] ReiserFS: hdb1: checking transaction log (hdb1)
[ 73.047880] ReiserFS: hdb1: Using r5 hash to sort names
[ 73.096394] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 73.096405] ReiserFS: hda2: using ordered data mode
[ 73.101224] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 73.102630] ReiserFS: hda2: checking transaction log (hda2)
[ 73.165531] ReiserFS: hda2: Using r5 hash to sort names
[ 79.014996] hda: UDMA/100 mode selected
[ 79.018892] hdb: UDMA/133 mode selected
[ 79.073585] hdc: UDMA/33 mode selected
[ 79.091357] hdd: UDMA/33 mode selected
[ 81.606735] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 85.836882] w83627hf: Found W83697HF chip at 0x290
[ 209.524283] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 209.524288] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 209.524291] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 209.524294] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 209.524296] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 209.524299] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 209.524301] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 209.524305] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 209.524308] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 209.524311] ata1: SError: { 10B8B }
[ 209.524316] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524320] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524325] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524329] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524333] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524338] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524342] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 209.524349] ata1.15: hard resetting link
[ 214.617980] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 214.869897] ata1.15: qc timeout (cmd 0xe4)
[ 214.869905] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 214.869908] ata1.15: PMP revalidation failed (errno=-5)
[ 214.869910] ata1.15: retrying hardreset in 5 secs
[ 219.872379] ata1.15: hard resetting link
[ 224.966839] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 225.173188] ata1.15: failed to read PMP GSCR[0] (Emask=0x100)
[ 225.173191] ata1.15: PMP revalidation failed (errno=-5)
[ 225.173194] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 225.173197] ata1.15: retrying hardreset in 5 secs
[ 230.173255] ata1.15: hard resetting link
[ 232.372597] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 232.372805] ata1.00: hard resetting link
[ 232.692677] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 232.692680] ata1.01: hard resetting link
[ 233.012579] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 233.012583] ata1.02: hard resetting link
[ 233.332482] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 233.332485] ata1.03: hard resetting link
[ 233.652385] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 233.652388] ata1.04: hard resetting link
[ 233.972289] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 233.972292] ata1.05: hard resetting link
[ 234.292189] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 234.292192] ata1.06: hard resetting link
[ 234.612092] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 234.614276] ata1.00: configured for UDMA/100
[ 234.616463] ata1.01: configured for UDMA/100
[ 234.719921] ata1.02: configured for UDMA/100
[ 234.821531] ata1.03: configured for UDMA/100
[ 234.821636] ata1.05: device is on DMA blacklist, disabling DMA
[ 234.821741] ata1.05: configured for PIO4
[ 234.821953] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
[ 234.821956] ata1.15: irq_stat 0x00800080, device exchanged
[ 234.822220] ata1: EH complete
[ 234.822245] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822256] sd 1:0:0:0: [sdb] Write Protect is off
[ 234.822259] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 234.822271] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822285] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822292] sd 1:1:0:0: [sdc] Write Protect is off
[ 234.822295] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 234.822305] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822318] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822325] sd 1:2:0:0: [sdd] Write Protect is off
[ 234.822328] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 234.822339] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822353] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822361] sd 1:3:0:0: [sde] Write Protect is off
[ 234.822363] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 234.822375] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822388] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 234.822396] sd 1:5:0:0: [sdf] Write Protect is off
[ 234.822399] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 234.822410] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822423] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822431] sd 1:0:0:0: [sdb] Write Protect is off
[ 234.822434] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 234.822445] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822458] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822465] sd 1:1:0:0: [sdc] Write Protect is off
[ 234.822468] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 234.822479] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822492] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822500] sd 1:2:0:0: [sdd] Write Protect is off
[ 234.822503] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 234.822514] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822527] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822534] sd 1:3:0:0: [sde] Write Protect is off
[ 234.822537] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 234.822549] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822561] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 234.822569] sd 1:5:0:0: [sdf] Write Protect is off
[ 234.822571] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 234.822583] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 396.287513] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 396.287519] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 396.287522] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 396.287525] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 396.287528] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 396.287531] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 396.287534] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 396.287539] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 396.287542] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 396.287546] ata1: SError: { 10B8B }
[ 396.287551] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287557] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287562] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287567] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287572] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287577] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287582] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287590] ata1.15: hard resetting link
[ 401.381322] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 401.633240] ata1.15: qc timeout (cmd 0xe4)
[ 401.633248] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 401.633251] ata1.15: PMP revalidation failed (errno=-5)
[ 401.633254] ata1.15: retrying hardreset in 5 secs
[ 406.635722] ata1.15: hard resetting link
[ 411.730181] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 411.982099] ata1.15: qc timeout (cmd 0xe4)
[ 411.982107] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 411.982110] ata1.15: PMP revalidation failed (errno=-5)
[ 411.982113] ata1.15: retrying hardreset in 5 secs
[ 416.984582] ata1.15: hard resetting link
[ 419.183924] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 419.184128] ata1.00: hard resetting link
[ 419.504005] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 419.504009] ata1.01: hard resetting link
[ 419.823907] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 419.823911] ata1.02: hard resetting link
[ 420.143811] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 420.143815] ata1.03: hard resetting link
[ 420.463713] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 420.463717] ata1.04: hard resetting link
[ 420.783616] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 420.783619] ata1.05: hard resetting link
[ 421.103516] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 421.103520] ata1.06: hard resetting link
[ 421.423426] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 421.423538] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423542] ata1.00: revalidation failed (errno=-5)
[ 421.423672] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423675] ata1.01: revalidation failed (errno=-5)
[ 421.423804] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423808] ata1.02: revalidation failed (errno=-5)
[ 421.423936] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423940] ata1.03: revalidation failed (errno=-5)
[ 421.424077] ata1.05: device is on DMA blacklist, disabling DMA
[ 421.424192] ata1.05: configured for PIO4
[ 421.424195] ata1: failed to recover some devices, retrying in 5 secs
[ 426.425719] ata1.00: hard resetting link
[ 426.745807] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 426.745811] ata1.01: hard resetting link
[ 427.065709] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 427.065713] ata1.02: hard resetting link
[ 427.385613] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 427.385617] ata1.03: hard resetting link
[ 427.705517] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 427.707726] ata1.00: configured for UDMA/100
[ 427.709957] ata1.01: configured for UDMA/100
[ 427.813721] ata1.02: configured for UDMA/100
[ 427.813822] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 427.813826] ata1.03: revalidation failed (errno=-5)
[ 427.813829] ata1: failed to recover some devices, retrying in 5 secs
[ 432.815779] ata1.03: hard resetting link
[ 433.135867] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 433.135974] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 433.135977] ata1.03: revalidation failed (errno=-5)
[ 433.135980] ata1.03: disabled
[ 433.639529] ata1.03: hard resetting link
[ 433.959617] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 433.959672] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 433.959676] ata1: failed to recover some devices, retrying in 5 secs
[ 438.961914] ata1.03: hard resetting link
[ 439.282004] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 439.282059] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 439.282062] ata1: failed to recover some devices, retrying in 5 secs
[ 444.284300] ata1.03: hard resetting link
[ 444.604390] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 444.604446] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 444.604450] ata1: failed to recover some devices, retrying in 5 secs
[ 449.606691] ata1.03: hard resetting link
[ 449.926776] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 449.927130] ata1: EH complete
[ 449.927174] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927186] sd 1:0:0:0: [sdb] Write Protect is off
[ 449.927189] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 449.927202] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927218] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927226] sd 1:1:0:0: [sdc] Write Protect is off
[ 449.927229] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 449.927240] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927254] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927262] sd 1:2:0:0: [sdd] Write Protect is off
[ 449.927264] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 449.927276] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927289] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 449.927297] sd 1:5:0:0: [sdf] Write Protect is off
[ 449.927299] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 449.927395] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927408] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927416] sd 1:0:0:0: [sdb] Write Protect is off
[ 449.927419] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 449.927430] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927442] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927450] sd 1:1:0:0: [sdc] Write Protect is off
[ 449.927453] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 449.927464] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927477] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927484] sd 1:2:0:0: [sdd] Write Protect is off
[ 449.927487] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 449.927498] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927511] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 449.927518] sd 1:5:0:0: [sdf] Write Protect is off
[ 449.927521] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 449.927532] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927538] ata1.03: detaching (SCSI 1:3:0:0)
[ 449.927717] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 449.928940] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 449.928945] sd 1:3:0:0: [sde] Stopping disk
[ 449.928950] sd 1:3:0:0: [sde] START_STOP FAILED
[ 449.928953] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 617.297502] ata1.15: limiting speed to UDMA7:PIO5
[ 617.297509] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 617.297512] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 617.297515] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 617.297518] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 617.297521] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 617.297524] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 617.297527] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 617.297531] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 617.297535] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 617.297539] ata1: SError: { 10B8B }
[ 617.297543] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297549] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297554] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297559] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297564] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297569] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297574] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297582] ata1.15: hard resetting link
[ 622.390270] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 622.642187] ata1.15: qc timeout (cmd 0xe4)
[ 622.642196] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 622.642199] ata1.15: PMP revalidation failed (errno=-5)
[ 622.642202] ata1.15: retrying hardreset in 5 secs
[ 627.644669] ata1.15: hard resetting link
[ 632.739129] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 632.991047] ata1.15: qc timeout (cmd 0xe4)
[ 632.991055] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 632.991058] ata1.15: PMP revalidation failed (errno=-5)
[ 632.991061] ata1.15: retrying hardreset in 5 secs
[ 637.993529] ata1.15: hard resetting link
[ 640.192871] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 640.193076] ata1.00: hard resetting link
[ 640.512952] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 640.512956] ata1.01: hard resetting link
[ 640.832853] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 640.832857] ata1.02: hard resetting link
[ 641.152758] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 641.152762] ata1.03: hard resetting link
[ 641.472660] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 641.472664] ata1.04: hard resetting link
[ 641.792562] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 641.792565] ata1.05: hard resetting link
[ 642.112464] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 642.112468] ata1.06: hard resetting link
[ 642.432369] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 642.434609] ata1.00: configured for UDMA/100
[ 642.436783] ata1.01: configured for UDMA/100
[ 642.548979] ata1.02: configured for UDMA/100
[ 642.597737] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 642.597741] ata1.03: 586072368 sectors, multi 0: LBA48
[ 642.597744] ata1.03: applying bridge limits
[ 642.656013] ata1.03: configured for UDMA/100
[ 642.656121] ata1.05: device is on DMA blacklist, disabling DMA
[ 642.656227] ata1.05: configured for PIO4
[ 642.656497] ata1: EH complete
[ 642.656522] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656534] sd 1:0:0:0: [sdb] Write Protect is off
[ 642.656537] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 642.656550] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656564] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656572] sd 1:1:0:0: [sdc] Write Protect is off
[ 642.656575] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 642.656586] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656600] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656608] sd 1:2:0:0: [sdd] Write Protect is off
[ 642.656610] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 642.656622] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656635] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 642.656643] sd 1:5:0:0: [sdf] Write Protect is off
[ 642.656646] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 642.656657] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656670] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656677] sd 1:0:0:0: [sdb] Write Protect is off
[ 642.656680] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 642.656692] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656704] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656712] sd 1:1:0:0: [sdc] Write Protect is off
[ 642.656715] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 642.656726] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656738] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656746] sd 1:2:0:0: [sdd] Write Protect is off
[ 642.656749] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 642.656760] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656773] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 642.656780] sd 1:5:0:0: [sdf] Write Protect is off
[ 642.656783] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 642.656794] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656866] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 642.657321] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 642.657330] sd 1:3:0:0: [sde] Write Protect is off
[ 642.657333] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 642.657345] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.657389] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 642.657796] sd 1:3:0:0: [sde] Write Protect is off
[ 642.657799] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 642.657815] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.657819] sde: sde1
[ 642.695754] sd 1:3:0:0: [sde] Attached SCSI disk
[ 642.695803] sd 1:3:0:0: Attached scsi generic sg5 type 0
[-- Attachment #5: 4_PowerOnOffTwice.log --]
[-- Type: text/plain, Size: 31310 bytes --]
[sdf] 640 512-byte hardware sectors (0 MB)
[ 234.822396] sd 1:5:0:0: [sdf] Write Protect is off
[ 234.822399] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 234.822410] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822423] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822431] sd 1:0:0:0: [sdb] Write Protect is off
[ 234.822434] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 234.822445] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822458] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822465] sd 1:1:0:0: [sdc] Write Protect is off
[ 234.822468] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 234.822479] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822492] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822500] sd 1:2:0:0: [sdd] Write Protect is off
[ 234.822503] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 234.822514] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822527] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 234.822534] sd 1:3:0:0: [sde] Write Protect is off
[ 234.822537] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 234.822549] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 234.822561] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 234.822569] sd 1:5:0:0: [sdf] Write Protect is off
[ 234.822571] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 234.822583] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 396.287513] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 396.287519] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 396.287522] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 396.287525] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 396.287528] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 396.287531] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 396.287534] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 396.287539] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 396.287542] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 396.287546] ata1: SError: { 10B8B }
[ 396.287551] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287557] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287562] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287567] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287572] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287577] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287582] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 396.287590] ata1.15: hard resetting link
[ 401.381322] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 401.633240] ata1.15: qc timeout (cmd 0xe4)
[ 401.633248] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 401.633251] ata1.15: PMP revalidation failed (errno=-5)
[ 401.633254] ata1.15: retrying hardreset in 5 secs
[ 406.635722] ata1.15: hard resetting link
[ 411.730181] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 411.982099] ata1.15: qc timeout (cmd 0xe4)
[ 411.982107] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 411.982110] ata1.15: PMP revalidation failed (errno=-5)
[ 411.982113] ata1.15: retrying hardreset in 5 secs
[ 416.984582] ata1.15: hard resetting link
[ 419.183924] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 419.184128] ata1.00: hard resetting link
[ 419.504005] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 419.504009] ata1.01: hard resetting link
[ 419.823907] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 419.823911] ata1.02: hard resetting link
[ 420.143811] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 420.143815] ata1.03: hard resetting link
[ 420.463713] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 420.463717] ata1.04: hard resetting link
[ 420.783616] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 420.783619] ata1.05: hard resetting link
[ 421.103516] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 421.103520] ata1.06: hard resetting link
[ 421.423426] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 421.423538] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423542] ata1.00: revalidation failed (errno=-5)
[ 421.423672] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423675] ata1.01: revalidation failed (errno=-5)
[ 421.423804] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423808] ata1.02: revalidation failed (errno=-5)
[ 421.423936] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 421.423940] ata1.03: revalidation failed (errno=-5)
[ 421.424077] ata1.05: device is on DMA blacklist, disabling DMA
[ 421.424192] ata1.05: configured for PIO4
[ 421.424195] ata1: failed to recover some devices, retrying in 5 secs
[ 426.425719] ata1.00: hard resetting link
[ 426.745807] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 426.745811] ata1.01: hard resetting link
[ 427.065709] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 427.065713] ata1.02: hard resetting link
[ 427.385613] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 427.385617] ata1.03: hard resetting link
[ 427.705517] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 427.707726] ata1.00: configured for UDMA/100
[ 427.709957] ata1.01: configured for UDMA/100
[ 427.813721] ata1.02: configured for UDMA/100
[ 427.813822] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 427.813826] ata1.03: revalidation failed (errno=-5)
[ 427.813829] ata1: failed to recover some devices, retrying in 5 secs
[ 432.815779] ata1.03: hard resetting link
[ 433.135867] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 433.135974] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 433.135977] ata1.03: revalidation failed (errno=-5)
[ 433.135980] ata1.03: disabled
[ 433.639529] ata1.03: hard resetting link
[ 433.959617] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 433.959672] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 433.959676] ata1: failed to recover some devices, retrying in 5 secs
[ 438.961914] ata1.03: hard resetting link
[ 439.282004] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 439.282059] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 439.282062] ata1: failed to recover some devices, retrying in 5 secs
[ 444.284300] ata1.03: hard resetting link
[ 444.604390] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 444.604446] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 444.604450] ata1: failed to recover some devices, retrying in 5 secs
[ 449.606691] ata1.03: hard resetting link
[ 449.926776] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 449.927130] ata1: EH complete
[ 449.927174] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927186] sd 1:0:0:0: [sdb] Write Protect is off
[ 449.927189] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 449.927202] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927218] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927226] sd 1:1:0:0: [sdc] Write Protect is off
[ 449.927229] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 449.927240] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927254] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927262] sd 1:2:0:0: [sdd] Write Protect is off
[ 449.927264] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 449.927276] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927289] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 449.927297] sd 1:5:0:0: [sdf] Write Protect is off
[ 449.927299] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 449.927395] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927408] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927416] sd 1:0:0:0: [sdb] Write Protect is off
[ 449.927419] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 449.927430] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927442] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927450] sd 1:1:0:0: [sdc] Write Protect is off
[ 449.927453] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 449.927464] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927477] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927484] sd 1:2:0:0: [sdd] Write Protect is off
[ 449.927487] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 449.927498] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927511] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 449.927518] sd 1:5:0:0: [sdf] Write Protect is off
[ 449.927521] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 449.927532] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927538] ata1.03: detaching (SCSI 1:3:0:0)
[ 449.927717] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 449.928940] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 449.928945] sd 1:3:0:0: [sde] Stopping disk
[ 449.928950] sd 1:3:0:0: [sde] START_STOP FAILED
[ 449.928953] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 617.297502] ata1.15: limiting speed to UDMA7:PIO5
[ 617.297509] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 617.297512] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 617.297515] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 617.297518] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 617.297521] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 617.297524] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 617.297527] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 617.297531] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 617.297535] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 617.297539] ata1: SError: { 10B8B }
[ 617.297543] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297549] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297554] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297559] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297564] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297569] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297574] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297582] ata1.15: hard resetting link
[ 622.390270] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 622.642187] ata1.15: qc timeout (cmd 0xe4)
[ 622.642196] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 622.642199] ata1.15: PMP revalidation failed (errno=-5)
[ 622.642202] ata1.15: retrying hardreset in 5 secs
[ 627.644669] ata1.15: hard resetting link
[ 632.739129] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 632.991047] ata1.15: qc timeout (cmd 0xe4)
[ 632.991055] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 632.991058] ata1.15: PMP revalidation failed (errno=-5)
[ 632.991061] ata1.15: retrying hardreset in 5 secs
[ 637.993529] ata1.15: hard resetting link
[ 640.192871] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 640.193076] ata1.00: hard resetting link
[ 640.512952] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 640.512956] ata1.01: hard resetting link
[ 640.832853] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 640.832857] ata1.02: hard resetting link
[ 641.152758] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 641.152762] ata1.03: hard resetting link
[ 641.472660] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 641.472664] ata1.04: hard resetting link
[ 641.792562] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 641.792565] ata1.05: hard resetting link
[ 642.112464] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 642.112468] ata1.06: hard resetting link
[ 642.432369] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 642.434609] ata1.00: configured for UDMA/100
[ 642.436783] ata1.01: configured for UDMA/100
[ 642.548979] ata1.02: configured for UDMA/100
[ 642.597737] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 642.597741] ata1.03: 586072368 sectors, multi 0: LBA48
[ 642.597744] ata1.03: applying bridge limits
[ 642.656013] ata1.03: configured for UDMA/100
[ 642.656121] ata1.05: device is on DMA blacklist, disabling DMA
[ 642.656227] ata1.05: configured for PIO4
[ 642.656497] ata1: EH complete
[ 642.656522] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656534] sd 1:0:0:0: [sdb] Write Protect is off
[ 642.656537] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 642.656550] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656564] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656572] sd 1:1:0:0: [sdc] Write Protect is off
[ 642.656575] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 642.656586] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656600] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656608] sd 1:2:0:0: [sdd] Write Protect is off
[ 642.656610] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 642.656622] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656635] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 642.656643] sd 1:5:0:0: [sdf] Write Protect is off
[ 642.656646] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 642.656657] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656670] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656677] sd 1:0:0:0: [sdb] Write Protect is off
[ 642.656680] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 642.656692] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656704] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656712] sd 1:1:0:0: [sdc] Write Protect is off
[ 642.656715] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 642.656726] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656738] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656746] sd 1:2:0:0: [sdd] Write Protect is off
[ 642.656749] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 642.656760] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656773] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 642.656780] sd 1:5:0:0: [sdf] Write Protect is off
[ 642.656783] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 642.656794] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656866] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 642.657321] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 642.657330] sd 1:3:0:0: [sde] Write Protect is off
[ 642.657333] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 642.657345] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.657389] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 642.657796] sd 1:3:0:0: [sde] Write Protect is off
[ 642.657799] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 642.657815] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.657819] sde: sde1
[ 642.695754] sd 1:3:0:0: [sde] Attached SCSI disk
[ 642.695803] sd 1:3:0:0: Attached scsi generic sg5 type 0
[ 810.992367] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 810.992373] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 810.992376] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 810.992379] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 810.992382] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 810.992385] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 810.992388] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 810.992393] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 810.992396] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 810.992400] ata1: SError: { 10B8B }
[ 810.992405] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992410] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992415] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992421] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992426] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992431] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992436] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992444] ata1.15: hard resetting link
[ 816.083507] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 816.335424] ata1.15: qc timeout (cmd 0xe4)
[ 816.335432] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 816.335435] ata1.15: PMP revalidation failed (errno=-5)
[ 816.335438] ata1.15: retrying hardreset in 5 secs
[ 821.337906] ata1.15: hard resetting link
[ 826.432365] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 826.684283] ata1.15: qc timeout (cmd 0xe4)
[ 826.684290] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 826.684293] ata1.15: PMP revalidation failed (errno=-5)
[ 826.684297] ata1.15: retrying hardreset in 5 secs
[ 831.686765] ata1.15: hard resetting link
[ 833.886108] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 833.886312] ata1.00: hard resetting link
[ 834.206188] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 834.206192] ata1.01: hard resetting link
[ 834.526091] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 834.526095] ata1.02: hard resetting link
[ 834.845993] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 834.845997] ata1.03: hard resetting link
[ 835.165897] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 835.165901] ata1.04: hard resetting link
[ 835.485800] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 835.485804] ata1.05: hard resetting link
[ 835.805701] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 835.805704] ata1.06: hard resetting link
[ 836.125608] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 836.125738] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 836.125742] ata1.00: revalidation failed (errno=-5)
[ 836.125871] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 836.125875] ata1.01: revalidation failed (errno=-5)
[ 836.126004] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 836.126007] ata1.02: revalidation failed (errno=-5)
[ 836.126136] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 836.126140] ata1.03: revalidation failed (errno=-5)
[ 836.126277] ata1.05: device is on DMA blacklist, disabling DMA
[ 836.126394] ata1.05: configured for PIO4
[ 836.126397] ata1: failed to recover some devices, retrying in 5 secs
[ 841.127902] ata1.00: hard resetting link
[ 841.447991] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 841.447995] ata1.01: hard resetting link
[ 841.767894] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 841.767898] ata1.02: hard resetting link
[ 842.087796] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 842.087800] ata1.03: hard resetting link
[ 842.407699] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 842.409866] ata1.00: configured for UDMA/100
[ 842.412082] ata1.01: configured for UDMA/100
[ 842.516615] ata1.02: configured for UDMA/100
[ 842.516722] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 842.516726] ata1.03: revalidation failed (errno=-5)
[ 842.516729] ata1: failed to recover some devices, retrying in 5 secs
[ 847.517963] ata1.03: hard resetting link
[ 847.838051] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 847.838156] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 847.838160] ata1.03: revalidation failed (errno=-5)
[ 847.838163] ata1.03: disabled
[ 848.341712] ata1.03: hard resetting link
[ 848.661801] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 848.661856] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 848.661859] ata1: failed to recover some devices, retrying in 5 secs
[ 853.664098] ata1.03: hard resetting link
[ 853.984187] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 853.984243] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 853.984246] ata1: failed to recover some devices, retrying in 5 secs
[ 858.986483] ata1.03: hard resetting link
[ 859.306572] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 859.306628] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 859.306631] ata1: failed to recover some devices, retrying in 5 secs
[ 864.308868] ata1.03: hard resetting link
[ 864.628957] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 864.629240] ata1: EH complete
[ 864.629267] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629278] sd 1:0:0:0: [sdb] Write Protect is off
[ 864.629282] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 864.629294] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629309] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629317] sd 1:1:0:0: [sdc] Write Protect is off
[ 864.629320] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 864.629331] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629345] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629352] sd 1:2:0:0: [sdd] Write Protect is off
[ 864.629355] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 864.629367] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629380] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 864.629387] sd 1:5:0:0: [sdf] Write Protect is off
[ 864.629390] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 864.629401] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629414] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629422] sd 1:0:0:0: [sdb] Write Protect is off
[ 864.629425] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 864.629436] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629448] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629456] sd 1:1:0:0: [sdc] Write Protect is off
[ 864.629458] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 864.629470] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629482] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629489] sd 1:2:0:0: [sdd] Write Protect is off
[ 864.629492] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 864.629503] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629516] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 864.629523] sd 1:5:0:0: [sdf] Write Protect is off
[ 864.629526] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 864.629537] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629542] ata1.03: detaching (SCSI 1:3:0:0)
[ 864.629721] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 864.630109] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 864.630113] sd 1:3:0:0: [sde] Stopping disk
[ 864.630119] sd 1:3:0:0: [sde] START_STOP FAILED
[ 864.630121] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 1232.464873] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1232.464879] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1232.464882] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1232.464885] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1232.464888] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1232.464891] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1232.464894] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1232.464899] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1232.464902] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1232.464906] ata1: SError: { 10B8B }
[ 1232.464911] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464916] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464921] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464926] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464931] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464936] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464942] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464949] ata1.15: hard resetting link
[ 1237.555650] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1237.807567] ata1.15: qc timeout (cmd 0xe4)
[ 1237.807575] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1237.807579] ata1.15: PMP revalidation failed (errno=-5)
[ 1237.807582] ata1.15: retrying hardreset in 5 secs
[ 1242.810049] ata1.15: hard resetting link
[ 1247.904509] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1248.156427] ata1.15: qc timeout (cmd 0xe4)
[ 1248.156435] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1248.156438] ata1.15: PMP revalidation failed (errno=-5)
[ 1248.156441] ata1.15: retrying hardreset in 5 secs
[ 1253.158910] ata1.15: hard resetting link
[ 1255.358253] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1255.358461] ata1.00: hard resetting link
[ 1255.678334] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1255.678338] ata1.01: hard resetting link
[ 1255.998235] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1255.998239] ata1.02: hard resetting link
[ 1256.318139] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1256.318143] ata1.03: hard resetting link
[ 1256.638042] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1256.638046] ata1.04: hard resetting link
[ 1256.957945] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1256.957948] ata1.05: hard resetting link
[ 1257.277845] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1257.277849] ata1.06: hard resetting link
[ 1257.597748] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1257.597864] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.597868] ata1.00: revalidation failed (errno=-5)
[ 1257.597997] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.598001] ata1.01: revalidation failed (errno=-5)
[ 1257.598129] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.598132] ata1.02: revalidation failed (errno=-5)
[ 1257.618319] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.618471] ata1.05: device is on DMA blacklist, disabling DMA
[ 1257.618624] ata1.05: configured for PIO4
[ 1257.618627] ata1: failed to recover some devices, retrying in 5 secs
[ 1262.620040] ata1.00: hard resetting link
[ 1262.940128] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1262.940132] ata1.01: hard resetting link
[ 1263.260032] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.260036] ata1.02: hard resetting link
[ 1263.579935] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.579939] ata1.03: hard resetting link
[ 1263.899837] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.902118] ata1.00: configured for UDMA/100
[ 1263.904377] ata1.01: configured for UDMA/100
[ 1264.006169] ata1.02: configured for UDMA/100
[ 1264.006262] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1264.006266] ata1: failed to recover some devices, retrying in 5 secs
[ 1269.006103] ata1.03: hard resetting link
[ 1269.326192] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1269.326294] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1269.326298] ata1: failed to recover some devices, retrying in 5 secs
[ 1274.328494] ata1.03: hard resetting link
[ 1274.648577] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1274.648860] ata1: EH complete
[ 1274.648888] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648900] sd 1:0:0:0: [sdb] Write Protect is off
[ 1274.648904] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1274.648917] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.648933] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648941] sd 1:1:0:0: [sdc] Write Protect is off
[ 1274.648944] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1274.648955] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.648969] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648976] sd 1:2:0:0: [sdd] Write Protect is off
[ 1274.648979] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1274.648991] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649004] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1274.649012] sd 1:5:0:0: [sdf] Write Protect is off
[ 1274.649014] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1274.649026] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649039] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649047] sd 1:0:0:0: [sdb] Write Protect is off
[ 1274.649049] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1274.649061] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649073] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649081] sd 1:1:0:0: [sdc] Write Protect is off
[ 1274.649084] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1274.649095] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649108] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649115] sd 1:2:0:0: [sdd] Write Protect is off
[ 1274.649118] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1274.649129] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649142] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1274.649149] sd 1:5:0:0: [sdf] Write Protect is off
[ 1274.649152] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1274.649164] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[-- Attachment #6: 5_DriveSwap.log --]
[-- Type: text/plain, Size: 31298 bytes --]
8 512-byte hardware sectors (300069 MB)
[ 449.927450] sd 1:1:0:0: [sdc] Write Protect is off
[ 449.927453] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 449.927464] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927477] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 449.927484] sd 1:2:0:0: [sdd] Write Protect is off
[ 449.927487] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 449.927498] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927511] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 449.927518] sd 1:5:0:0: [sdf] Write Protect is off
[ 449.927521] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 449.927532] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 449.927538] ata1.03: detaching (SCSI 1:3:0:0)
[ 449.927717] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 449.928940] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 449.928945] sd 1:3:0:0: [sde] Stopping disk
[ 449.928950] sd 1:3:0:0: [sde] START_STOP FAILED
[ 449.928953] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 617.297502] ata1.15: limiting speed to UDMA7:PIO5
[ 617.297509] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 617.297512] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 617.297515] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 617.297518] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 617.297521] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 617.297524] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 617.297527] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 617.297531] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 617.297535] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 617.297539] ata1: SError: { 10B8B }
[ 617.297543] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297549] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297554] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297559] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297564] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297569] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297574] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 617.297582] ata1.15: hard resetting link
[ 622.390270] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 622.642187] ata1.15: qc timeout (cmd 0xe4)
[ 622.642196] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 622.642199] ata1.15: PMP revalidation failed (errno=-5)
[ 622.642202] ata1.15: retrying hardreset in 5 secs
[ 627.644669] ata1.15: hard resetting link
[ 632.739129] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 632.991047] ata1.15: qc timeout (cmd 0xe4)
[ 632.991055] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 632.991058] ata1.15: PMP revalidation failed (errno=-5)
[ 632.991061] ata1.15: retrying hardreset in 5 secs
[ 637.993529] ata1.15: hard resetting link
[ 640.192871] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 640.193076] ata1.00: hard resetting link
[ 640.512952] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 640.512956] ata1.01: hard resetting link
[ 640.832853] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 640.832857] ata1.02: hard resetting link
[ 641.152758] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 641.152762] ata1.03: hard resetting link
[ 641.472660] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 641.472664] ata1.04: hard resetting link
[ 641.792562] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 641.792565] ata1.05: hard resetting link
[ 642.112464] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 642.112468] ata1.06: hard resetting link
[ 642.432369] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 642.434609] ata1.00: configured for UDMA/100
[ 642.436783] ata1.01: configured for UDMA/100
[ 642.548979] ata1.02: configured for UDMA/100
[ 642.597737] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 642.597741] ata1.03: 586072368 sectors, multi 0: LBA48
[ 642.597744] ata1.03: applying bridge limits
[ 642.656013] ata1.03: configured for UDMA/100
[ 642.656121] ata1.05: device is on DMA blacklist, disabling DMA
[ 642.656227] ata1.05: configured for PIO4
[ 642.656497] ata1: EH complete
[ 642.656522] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656534] sd 1:0:0:0: [sdb] Write Protect is off
[ 642.656537] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 642.656550] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656564] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656572] sd 1:1:0:0: [sdc] Write Protect is off
[ 642.656575] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 642.656586] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656600] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656608] sd 1:2:0:0: [sdd] Write Protect is off
[ 642.656610] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 642.656622] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656635] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 642.656643] sd 1:5:0:0: [sdf] Write Protect is off
[ 642.656646] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 642.656657] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656670] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656677] sd 1:0:0:0: [sdb] Write Protect is off
[ 642.656680] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 642.656692] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656704] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656712] sd 1:1:0:0: [sdc] Write Protect is off
[ 642.656715] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 642.656726] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656738] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 642.656746] sd 1:2:0:0: [sdd] Write Protect is off
[ 642.656749] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 642.656760] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656773] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 642.656780] sd 1:5:0:0: [sdf] Write Protect is off
[ 642.656783] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 642.656794] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 642.656866] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 642.657321] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 642.657330] sd 1:3:0:0: [sde] Write Protect is off
[ 642.657333] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 642.657345] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.657389] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 642.657796] sd 1:3:0:0: [sde] Write Protect is off
[ 642.657799] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 642.657815] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 642.657819] sde: sde1
[ 642.695754] sd 1:3:0:0: [sde] Attached SCSI disk
[ 642.695803] sd 1:3:0:0: Attached scsi generic sg5 type 0
[ 810.992367] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 810.992373] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 810.992376] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 810.992379] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 810.992382] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 810.992385] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 810.992388] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 810.992393] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 810.992396] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 810.992400] ata1: SError: { 10B8B }
[ 810.992405] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992410] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992415] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992421] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992426] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992431] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992436] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 810.992444] ata1.15: hard resetting link
[ 816.083507] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 816.335424] ata1.15: qc timeout (cmd 0xe4)
[ 816.335432] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 816.335435] ata1.15: PMP revalidation failed (errno=-5)
[ 816.335438] ata1.15: retrying hardreset in 5 secs
[ 821.337906] ata1.15: hard resetting link
[ 826.432365] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 826.684283] ata1.15: qc timeout (cmd 0xe4)
[ 826.684290] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 826.684293] ata1.15: PMP revalidation failed (errno=-5)
[ 826.684297] ata1.15: retrying hardreset in 5 secs
[ 831.686765] ata1.15: hard resetting link
[ 833.886108] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 833.886312] ata1.00: hard resetting link
[ 834.206188] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 834.206192] ata1.01: hard resetting link
[ 834.526091] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 834.526095] ata1.02: hard resetting link
[ 834.845993] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 834.845997] ata1.03: hard resetting link
[ 835.165897] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 835.165901] ata1.04: hard resetting link
[ 835.485800] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 835.485804] ata1.05: hard resetting link
[ 835.805701] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 835.805704] ata1.06: hard resetting link
[ 836.125608] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 836.125738] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 836.125742] ata1.00: revalidation failed (errno=-5)
[ 836.125871] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 836.125875] ata1.01: revalidation failed (errno=-5)
[ 836.126004] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 836.126007] ata1.02: revalidation failed (errno=-5)
[ 836.126136] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 836.126140] ata1.03: revalidation failed (errno=-5)
[ 836.126277] ata1.05: device is on DMA blacklist, disabling DMA
[ 836.126394] ata1.05: configured for PIO4
[ 836.126397] ata1: failed to recover some devices, retrying in 5 secs
[ 841.127902] ata1.00: hard resetting link
[ 841.447991] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 841.447995] ata1.01: hard resetting link
[ 841.767894] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 841.767898] ata1.02: hard resetting link
[ 842.087796] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 842.087800] ata1.03: hard resetting link
[ 842.407699] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 842.409866] ata1.00: configured for UDMA/100
[ 842.412082] ata1.01: configured for UDMA/100
[ 842.516615] ata1.02: configured for UDMA/100
[ 842.516722] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 842.516726] ata1.03: revalidation failed (errno=-5)
[ 842.516729] ata1: failed to recover some devices, retrying in 5 secs
[ 847.517963] ata1.03: hard resetting link
[ 847.838051] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 847.838156] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 847.838160] ata1.03: revalidation failed (errno=-5)
[ 847.838163] ata1.03: disabled
[ 848.341712] ata1.03: hard resetting link
[ 848.661801] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 848.661856] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 848.661859] ata1: failed to recover some devices, retrying in 5 secs
[ 853.664098] ata1.03: hard resetting link
[ 853.984187] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 853.984243] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 853.984246] ata1: failed to recover some devices, retrying in 5 secs
[ 858.986483] ata1.03: hard resetting link
[ 859.306572] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 859.306628] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 859.306631] ata1: failed to recover some devices, retrying in 5 secs
[ 864.308868] ata1.03: hard resetting link
[ 864.628957] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 864.629240] ata1: EH complete
[ 864.629267] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629278] sd 1:0:0:0: [sdb] Write Protect is off
[ 864.629282] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 864.629294] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629309] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629317] sd 1:1:0:0: [sdc] Write Protect is off
[ 864.629320] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 864.629331] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629345] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629352] sd 1:2:0:0: [sdd] Write Protect is off
[ 864.629355] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 864.629367] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629380] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 864.629387] sd 1:5:0:0: [sdf] Write Protect is off
[ 864.629390] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 864.629401] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629414] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629422] sd 1:0:0:0: [sdb] Write Protect is off
[ 864.629425] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 864.629436] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629448] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629456] sd 1:1:0:0: [sdc] Write Protect is off
[ 864.629458] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 864.629470] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629482] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629489] sd 1:2:0:0: [sdd] Write Protect is off
[ 864.629492] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 864.629503] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629516] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 864.629523] sd 1:5:0:0: [sdf] Write Protect is off
[ 864.629526] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 864.629537] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629542] ata1.03: detaching (SCSI 1:3:0:0)
[ 864.629721] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 864.630109] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 864.630113] sd 1:3:0:0: [sde] Stopping disk
[ 864.630119] sd 1:3:0:0: [sde] START_STOP FAILED
[ 864.630121] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 1232.464873] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1232.464879] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1232.464882] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1232.464885] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1232.464888] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1232.464891] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1232.464894] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1232.464899] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1232.464902] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1232.464906] ata1: SError: { 10B8B }
[ 1232.464911] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464916] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464921] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464926] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464931] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464936] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464942] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464949] ata1.15: hard resetting link
[ 1237.555650] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1237.807567] ata1.15: qc timeout (cmd 0xe4)
[ 1237.807575] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1237.807579] ata1.15: PMP revalidation failed (errno=-5)
[ 1237.807582] ata1.15: retrying hardreset in 5 secs
[ 1242.810049] ata1.15: hard resetting link
[ 1247.904509] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1248.156427] ata1.15: qc timeout (cmd 0xe4)
[ 1248.156435] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1248.156438] ata1.15: PMP revalidation failed (errno=-5)
[ 1248.156441] ata1.15: retrying hardreset in 5 secs
[ 1253.158910] ata1.15: hard resetting link
[ 1255.358253] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1255.358461] ata1.00: hard resetting link
[ 1255.678334] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1255.678338] ata1.01: hard resetting link
[ 1255.998235] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1255.998239] ata1.02: hard resetting link
[ 1256.318139] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1256.318143] ata1.03: hard resetting link
[ 1256.638042] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1256.638046] ata1.04: hard resetting link
[ 1256.957945] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1256.957948] ata1.05: hard resetting link
[ 1257.277845] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1257.277849] ata1.06: hard resetting link
[ 1257.597748] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1257.597864] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.597868] ata1.00: revalidation failed (errno=-5)
[ 1257.597997] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.598001] ata1.01: revalidation failed (errno=-5)
[ 1257.598129] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.598132] ata1.02: revalidation failed (errno=-5)
[ 1257.618319] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.618471] ata1.05: device is on DMA blacklist, disabling DMA
[ 1257.618624] ata1.05: configured for PIO4
[ 1257.618627] ata1: failed to recover some devices, retrying in 5 secs
[ 1262.620040] ata1.00: hard resetting link
[ 1262.940128] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1262.940132] ata1.01: hard resetting link
[ 1263.260032] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.260036] ata1.02: hard resetting link
[ 1263.579935] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.579939] ata1.03: hard resetting link
[ 1263.899837] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.902118] ata1.00: configured for UDMA/100
[ 1263.904377] ata1.01: configured for UDMA/100
[ 1264.006169] ata1.02: configured for UDMA/100
[ 1264.006262] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1264.006266] ata1: failed to recover some devices, retrying in 5 secs
[ 1269.006103] ata1.03: hard resetting link
[ 1269.326192] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1269.326294] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1269.326298] ata1: failed to recover some devices, retrying in 5 secs
[ 1274.328494] ata1.03: hard resetting link
[ 1274.648577] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1274.648860] ata1: EH complete
[ 1274.648888] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648900] sd 1:0:0:0: [sdb] Write Protect is off
[ 1274.648904] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1274.648917] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.648933] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648941] sd 1:1:0:0: [sdc] Write Protect is off
[ 1274.648944] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1274.648955] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.648969] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648976] sd 1:2:0:0: [sdd] Write Protect is off
[ 1274.648979] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1274.648991] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649004] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1274.649012] sd 1:5:0:0: [sdf] Write Protect is off
[ 1274.649014] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1274.649026] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649039] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649047] sd 1:0:0:0: [sdb] Write Protect is off
[ 1274.649049] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1274.649061] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649073] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649081] sd 1:1:0:0: [sdc] Write Protect is off
[ 1274.649084] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1274.649095] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649108] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649115] sd 1:2:0:0: [sdd] Write Protect is off
[ 1274.649118] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1274.649129] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649142] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1274.649149] sd 1:5:0:0: [sdf] Write Protect is off
[ 1274.649152] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1274.649164] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1568.422342] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1568.422348] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1568.422351] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1568.422354] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1568.422357] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1568.422360] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1568.422363] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1568.422368] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1568.422371] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1568.422375] ata1: SError: { 10B8B }
[ 1568.422380] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422385] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422390] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422396] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422401] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422406] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422411] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422418] ata1.15: hard resetting link
[ 1573.513729] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1573.765647] ata1.15: qc timeout (cmd 0xe4)
[ 1573.765655] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1573.765658] ata1.15: PMP revalidation failed (errno=-5)
[ 1573.765661] ata1.15: retrying hardreset in 5 secs
[ 1578.768128] ata1.15: hard resetting link
[ 1583.862588] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1584.114506] ata1.15: qc timeout (cmd 0xe4)
[ 1584.114513] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1584.114516] ata1.15: PMP revalidation failed (errno=-5)
[ 1584.114520] ata1.15: retrying hardreset in 5 secs
[ 1589.116988] ata1.15: hard resetting link
[ 1594.211450] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1594.463368] ata1.15: qc timeout (cmd 0xe4)
[ 1594.463375] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1594.463378] ata1.15: PMP revalidation failed (errno=-5)
[ 1594.463382] ata1.15: retrying hardreset in 5 secs
[ 1599.465849] ata1.15: hard resetting link
[ 1604.560308] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1604.812227] ata1.15: qc timeout (cmd 0xe4)
[ 1604.812234] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1604.812237] ata1.15: PMP revalidation failed (errno=-5)
[ 1604.812241] ata1.15: retrying hardreset in 5 secs
[ 1609.814709] ata1.15: hard resetting link
[ 1612.741831] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1612.742041] ata1.00: hard resetting link
[ 1613.061909] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1613.061913] ata1.01: hard resetting link
[ 1613.381812] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1613.381816] ata1.02: hard resetting link
[ 1613.701716] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1613.701720] ata1.03: hard resetting link
[ 1614.021621] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1614.021624] ata1.04: hard resetting link
[ 1614.341521] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1614.341524] ata1.05: hard resetting link
[ 1614.661422] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1614.661426] ata1.06: hard resetting link
[ 1614.981331] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1614.981438] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1614.981442] ata1.00: revalidation failed (errno=-5)
[ 1614.981572] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1614.981575] ata1.01: revalidation failed (errno=-5)
[ 1614.981703] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1614.981706] ata1.02: revalidation failed (errno=-5)
[ 1615.001891] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1615.002073] ata1.05: device is on DMA blacklist, disabling DMA
[ 1615.002229] ata1.05: configured for PIO4
[ 1615.002232] ata1: failed to recover some devices, retrying in 5 secs
[ 1620.003619] ata1.00: hard resetting link
[ 1620.323706] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1620.323710] ata1.01: hard resetting link
[ 1620.643612] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1620.643616] ata1.02: hard resetting link
[ 1620.963513] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1620.963517] ata1.03: hard resetting link
[ 1621.283416] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1621.285731] ata1.00: configured for UDMA/100
[ 1621.287984] ata1.01: configured for UDMA/100
[ 1621.289160] ata1.02: serial number mismatch ' 3NF1H4DW' != ' 3NF1JSWM'
[ 1621.289165] ata1.02: revalidation failed (errno=-19)
[ 1621.289287] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1621.289290] ata1: failed to recover some devices, retrying in 5 secs
[ 1626.289712] ata1.02: hard resetting link
[ 1626.609800] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1626.609804] ata1.03: hard resetting link
[ 1626.929703] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1626.930885] ata1.02: serial number mismatch ' 3NF1H4DW' != ' 3NF1JSWM'
[ 1626.930889] ata1.02: revalidation failed (errno=-19)
[ 1626.930892] ata1.02: disabled
[ 1626.931064] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1626.931068] ata1: failed to recover some devices, retrying in 5 secs
[ 1631.932005] ata1.02: hard resetting link
[ 1632.252089] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1632.252094] ata1.03: hard resetting link
[ 1632.571990] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1632.619011] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 1632.619015] ata1.02: 586072368 sectors, multi 0: LBA48
[ 1632.619019] ata1.02: applying bridge limits
[ 1632.677283] ata1.02: configured for UDMA/100
[ 1632.677559] ata1: EH complete
[ 1632.677586] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677598] sd 1:0:0:0: [sdb] Write Protect is off
[ 1632.677602] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1632.677615] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677630] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677638] sd 1:1:0:0: [sdc] Write Protect is off
[ 1632.677641] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1632.677652] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677666] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1632.677674] sd 1:5:0:0: [sdf] Write Protect is off
[ 1632.677677] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1632.677688] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677701] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677708] sd 1:0:0:0: [sdb] Write Protect is off
[ 1632.677711] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1632.677722] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677735] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677742] sd 1:1:0:0: [sdc] Write Protect is off
[ 1632.677745] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1632.677756] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677769] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1632.677776] sd 1:5:0:0: [sdf] Write Protect is off
[ 1632.677779] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1632.677790] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677796] ata1.02: detaching (SCSI 1:2:0:0)
[ 1632.677972] sd 1:2:0:0: [sdd] Synchronizing SCSI cache
[ 1632.701650] sd 1:2:0:0: [sdd] Stopping disk
[ 1632.701883] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 1632.701973] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.701993] sd 1:2:0:0: [sdd] Write Protect is off
[ 1632.701997] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1632.702148] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.702209] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.702227] sd 1:2:0:0: [sdd] Write Protect is off
[ 1632.702230] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1632.702257] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.702261] sdd: sdd1
[ 1633.333656] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 1633.333704] sd 1:2:0:0: Attached scsi generic sg4 type 0
[-- Attachment #7: 6_PowerOnOffTwice.log --]
[-- Type: text/plain, Size: 31310 bytes --]
secs
[ 864.308868] ata1.03: hard resetting link
[ 864.628957] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 864.629240] ata1: EH complete
[ 864.629267] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629278] sd 1:0:0:0: [sdb] Write Protect is off
[ 864.629282] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 864.629294] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629309] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629317] sd 1:1:0:0: [sdc] Write Protect is off
[ 864.629320] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 864.629331] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629345] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629352] sd 1:2:0:0: [sdd] Write Protect is off
[ 864.629355] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 864.629367] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629380] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 864.629387] sd 1:5:0:0: [sdf] Write Protect is off
[ 864.629390] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 864.629401] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629414] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629422] sd 1:0:0:0: [sdb] Write Protect is off
[ 864.629425] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 864.629436] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629448] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629456] sd 1:1:0:0: [sdc] Write Protect is off
[ 864.629458] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 864.629470] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629482] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 864.629489] sd 1:2:0:0: [sdd] Write Protect is off
[ 864.629492] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 864.629503] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629516] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 864.629523] sd 1:5:0:0: [sdf] Write Protect is off
[ 864.629526] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 864.629537] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 864.629542] ata1.03: detaching (SCSI 1:3:0:0)
[ 864.629721] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 864.630109] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 864.630113] sd 1:3:0:0: [sde] Stopping disk
[ 864.630119] sd 1:3:0:0: [sde] START_STOP FAILED
[ 864.630121] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 1232.464873] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1232.464879] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1232.464882] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1232.464885] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1232.464888] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1232.464891] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1232.464894] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1232.464899] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1232.464902] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1232.464906] ata1: SError: { 10B8B }
[ 1232.464911] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464916] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464921] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464926] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464931] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464936] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464942] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1232.464949] ata1.15: hard resetting link
[ 1237.555650] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1237.807567] ata1.15: qc timeout (cmd 0xe4)
[ 1237.807575] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1237.807579] ata1.15: PMP revalidation failed (errno=-5)
[ 1237.807582] ata1.15: retrying hardreset in 5 secs
[ 1242.810049] ata1.15: hard resetting link
[ 1247.904509] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1248.156427] ata1.15: qc timeout (cmd 0xe4)
[ 1248.156435] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1248.156438] ata1.15: PMP revalidation failed (errno=-5)
[ 1248.156441] ata1.15: retrying hardreset in 5 secs
[ 1253.158910] ata1.15: hard resetting link
[ 1255.358253] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1255.358461] ata1.00: hard resetting link
[ 1255.678334] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1255.678338] ata1.01: hard resetting link
[ 1255.998235] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1255.998239] ata1.02: hard resetting link
[ 1256.318139] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1256.318143] ata1.03: hard resetting link
[ 1256.638042] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1256.638046] ata1.04: hard resetting link
[ 1256.957945] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1256.957948] ata1.05: hard resetting link
[ 1257.277845] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1257.277849] ata1.06: hard resetting link
[ 1257.597748] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1257.597864] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.597868] ata1.00: revalidation failed (errno=-5)
[ 1257.597997] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.598001] ata1.01: revalidation failed (errno=-5)
[ 1257.598129] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.598132] ata1.02: revalidation failed (errno=-5)
[ 1257.618319] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1257.618471] ata1.05: device is on DMA blacklist, disabling DMA
[ 1257.618624] ata1.05: configured for PIO4
[ 1257.618627] ata1: failed to recover some devices, retrying in 5 secs
[ 1262.620040] ata1.00: hard resetting link
[ 1262.940128] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1262.940132] ata1.01: hard resetting link
[ 1263.260032] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.260036] ata1.02: hard resetting link
[ 1263.579935] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.579939] ata1.03: hard resetting link
[ 1263.899837] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.902118] ata1.00: configured for UDMA/100
[ 1263.904377] ata1.01: configured for UDMA/100
[ 1264.006169] ata1.02: configured for UDMA/100
[ 1264.006262] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1264.006266] ata1: failed to recover some devices, retrying in 5 secs
[ 1269.006103] ata1.03: hard resetting link
[ 1269.326192] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1269.326294] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1269.326298] ata1: failed to recover some devices, retrying in 5 secs
[ 1274.328494] ata1.03: hard resetting link
[ 1274.648577] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1274.648860] ata1: EH complete
[ 1274.648888] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648900] sd 1:0:0:0: [sdb] Write Protect is off
[ 1274.648904] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1274.648917] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.648933] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648941] sd 1:1:0:0: [sdc] Write Protect is off
[ 1274.648944] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1274.648955] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.648969] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648976] sd 1:2:0:0: [sdd] Write Protect is off
[ 1274.648979] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1274.648991] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649004] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1274.649012] sd 1:5:0:0: [sdf] Write Protect is off
[ 1274.649014] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1274.649026] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649039] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649047] sd 1:0:0:0: [sdb] Write Protect is off
[ 1274.649049] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1274.649061] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649073] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649081] sd 1:1:0:0: [sdc] Write Protect is off
[ 1274.649084] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1274.649095] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649108] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649115] sd 1:2:0:0: [sdd] Write Protect is off
[ 1274.649118] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1274.649129] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649142] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1274.649149] sd 1:5:0:0: [sdf] Write Protect is off
[ 1274.649152] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1274.649164] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1568.422342] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1568.422348] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1568.422351] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1568.422354] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1568.422357] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1568.422360] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1568.422363] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1568.422368] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1568.422371] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1568.422375] ata1: SError: { 10B8B }
[ 1568.422380] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422385] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422390] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422396] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422401] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422406] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422411] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422418] ata1.15: hard resetting link
[ 1573.513729] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1573.765647] ata1.15: qc timeout (cmd 0xe4)
[ 1573.765655] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1573.765658] ata1.15: PMP revalidation failed (errno=-5)
[ 1573.765661] ata1.15: retrying hardreset in 5 secs
[ 1578.768128] ata1.15: hard resetting link
[ 1583.862588] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1584.114506] ata1.15: qc timeout (cmd 0xe4)
[ 1584.114513] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1584.114516] ata1.15: PMP revalidation failed (errno=-5)
[ 1584.114520] ata1.15: retrying hardreset in 5 secs
[ 1589.116988] ata1.15: hard resetting link
[ 1594.211450] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1594.463368] ata1.15: qc timeout (cmd 0xe4)
[ 1594.463375] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1594.463378] ata1.15: PMP revalidation failed (errno=-5)
[ 1594.463382] ata1.15: retrying hardreset in 5 secs
[ 1599.465849] ata1.15: hard resetting link
[ 1604.560308] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1604.812227] ata1.15: qc timeout (cmd 0xe4)
[ 1604.812234] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1604.812237] ata1.15: PMP revalidation failed (errno=-5)
[ 1604.812241] ata1.15: retrying hardreset in 5 secs
[ 1609.814709] ata1.15: hard resetting link
[ 1612.741831] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1612.742041] ata1.00: hard resetting link
[ 1613.061909] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1613.061913] ata1.01: hard resetting link
[ 1613.381812] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1613.381816] ata1.02: hard resetting link
[ 1613.701716] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1613.701720] ata1.03: hard resetting link
[ 1614.021621] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1614.021624] ata1.04: hard resetting link
[ 1614.341521] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1614.341524] ata1.05: hard resetting link
[ 1614.661422] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1614.661426] ata1.06: hard resetting link
[ 1614.981331] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1614.981438] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1614.981442] ata1.00: revalidation failed (errno=-5)
[ 1614.981572] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1614.981575] ata1.01: revalidation failed (errno=-5)
[ 1614.981703] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1614.981706] ata1.02: revalidation failed (errno=-5)
[ 1615.001891] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1615.002073] ata1.05: device is on DMA blacklist, disabling DMA
[ 1615.002229] ata1.05: configured for PIO4
[ 1615.002232] ata1: failed to recover some devices, retrying in 5 secs
[ 1620.003619] ata1.00: hard resetting link
[ 1620.323706] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1620.323710] ata1.01: hard resetting link
[ 1620.643612] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1620.643616] ata1.02: hard resetting link
[ 1620.963513] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1620.963517] ata1.03: hard resetting link
[ 1621.283416] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1621.285731] ata1.00: configured for UDMA/100
[ 1621.287984] ata1.01: configured for UDMA/100
[ 1621.289160] ata1.02: serial number mismatch ' 3NF1H4DW' != ' 3NF1JSWM'
[ 1621.289165] ata1.02: revalidation failed (errno=-19)
[ 1621.289287] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1621.289290] ata1: failed to recover some devices, retrying in 5 secs
[ 1626.289712] ata1.02: hard resetting link
[ 1626.609800] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1626.609804] ata1.03: hard resetting link
[ 1626.929703] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1626.930885] ata1.02: serial number mismatch ' 3NF1H4DW' != ' 3NF1JSWM'
[ 1626.930889] ata1.02: revalidation failed (errno=-19)
[ 1626.930892] ata1.02: disabled
[ 1626.931064] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1626.931068] ata1: failed to recover some devices, retrying in 5 secs
[ 1631.932005] ata1.02: hard resetting link
[ 1632.252089] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1632.252094] ata1.03: hard resetting link
[ 1632.571990] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1632.619011] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 1632.619015] ata1.02: 586072368 sectors, multi 0: LBA48
[ 1632.619019] ata1.02: applying bridge limits
[ 1632.677283] ata1.02: configured for UDMA/100
[ 1632.677559] ata1: EH complete
[ 1632.677586] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677598] sd 1:0:0:0: [sdb] Write Protect is off
[ 1632.677602] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1632.677615] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677630] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677638] sd 1:1:0:0: [sdc] Write Protect is off
[ 1632.677641] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1632.677652] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677666] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1632.677674] sd 1:5:0:0: [sdf] Write Protect is off
[ 1632.677677] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1632.677688] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677701] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677708] sd 1:0:0:0: [sdb] Write Protect is off
[ 1632.677711] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1632.677722] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677735] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677742] sd 1:1:0:0: [sdc] Write Protect is off
[ 1632.677745] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1632.677756] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677769] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1632.677776] sd 1:5:0:0: [sdf] Write Protect is off
[ 1632.677779] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1632.677790] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677796] ata1.02: detaching (SCSI 1:2:0:0)
[ 1632.677972] sd 1:2:0:0: [sdd] Synchronizing SCSI cache
[ 1632.701650] sd 1:2:0:0: [sdd] Stopping disk
[ 1632.701883] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 1632.701973] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.701993] sd 1:2:0:0: [sdd] Write Protect is off
[ 1632.701997] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1632.702148] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.702209] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.702227] sd 1:2:0:0: [sdd] Write Protect is off
[ 1632.702230] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1632.702257] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.702261] sdd: sdd1
[ 1633.333656] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 1633.333704] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 1768.255041] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1768.255047] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1768.255050] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1768.255053] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1768.255056] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1768.255059] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1768.255062] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1768.255066] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1768.255070] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1768.255074] ata1: SError: { 10B8B }
[ 1768.255078] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255084] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255089] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255094] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255099] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255104] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255110] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255117] ata1.15: hard resetting link
[ 1773.349102] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1773.601020] ata1.15: qc timeout (cmd 0xe4)
[ 1773.601028] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1773.601031] ata1.15: PMP revalidation failed (errno=-5)
[ 1773.601034] ata1.15: retrying hardreset in 5 secs
[ 1778.603503] ata1.15: hard resetting link
[ 1783.697963] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1783.949880] ata1.15: qc timeout (cmd 0xe4)
[ 1783.949888] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1783.949891] ata1.15: PMP revalidation failed (errno=-5)
[ 1783.949894] ata1.15: retrying hardreset in 5 secs
[ 1788.952363] ata1.15: hard resetting link
[ 1791.151705] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1791.151910] ata1.00: hard resetting link
[ 1791.471785] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1791.471789] ata1.01: hard resetting link
[ 1791.791689] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1791.791693] ata1.02: hard resetting link
[ 1792.111591] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1792.111595] ata1.03: hard resetting link
[ 1792.431493] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1792.431497] ata1.04: hard resetting link
[ 1792.751397] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1792.751400] ata1.05: hard resetting link
[ 1793.071297] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1793.071300] ata1.06: hard resetting link
[ 1793.391206] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1793.393501] ata1.00: configured for UDMA/100
[ 1793.395703] ata1.01: configured for UDMA/100
[ 1793.395805] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1793.395809] ata1.02: revalidation failed (errno=-5)
[ 1793.415996] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1793.416141] ata1.05: device is on DMA blacklist, disabling DMA
[ 1793.416285] ata1.05: configured for PIO4
[ 1793.416288] ata1: failed to recover some devices, retrying in 5 secs
[ 1798.417497] ata1.02: hard resetting link
[ 1798.737581] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1798.737585] ata1.03: hard resetting link
[ 1799.057481] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1799.165478] ata1.02: configured for UDMA/100
[ 1799.165534] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1799.165538] ata1: failed to recover some devices, retrying in 5 secs
[ 1804.167747] ata1.03: hard resetting link
[ 1804.487836] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1804.487893] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1804.487897] ata1: failed to recover some devices, retrying in 5 secs
[ 1809.490138] ata1.03: hard resetting link
[ 1809.810221] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1809.810543] ata1: EH complete
[ 1809.810584] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810596] sd 1:0:0:0: [sdb] Write Protect is off
[ 1809.810599] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1809.810612] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810628] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810636] sd 1:1:0:0: [sdc] Write Protect is off
[ 1809.810639] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1809.810650] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810664] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810672] sd 1:2:0:0: [sdd] Write Protect is off
[ 1809.810675] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1809.810686] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810699] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1809.810707] sd 1:5:0:0: [sdf] Write Protect is off
[ 1809.810710] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1809.810721] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810734] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810742] sd 1:0:0:0: [sdb] Write Protect is off
[ 1809.810744] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1809.810756] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810768] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810775] sd 1:1:0:0: [sdc] Write Protect is off
[ 1809.810778] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1809.810789] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810802] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810809] sd 1:2:0:0: [sdd] Write Protect is off
[ 1809.810812] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1809.810823] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810931] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1809.810939] sd 1:5:0:0: [sdf] Write Protect is off
[ 1809.810941] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1809.810953] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1962.834896] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1962.834903] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1962.834906] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1962.834909] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1962.834912] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1962.834915] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1962.834918] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1962.834923] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1962.834926] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1962.834930] ata1: SError: { 10B8B }
[ 1962.834935] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834940] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834945] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834950] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834955] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834961] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834966] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834973] ata1.15: hard resetting link
[ 1967.926071] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1968.177988] ata1.15: qc timeout (cmd 0xe4)
[ 1968.177996] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1968.177999] ata1.15: PMP revalidation failed (errno=-5)
[ 1968.178002] ata1.15: retrying hardreset in 5 secs
[ 1973.180470] ata1.15: hard resetting link
[ 1978.082992] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1978.083197] ata1.00: hard resetting link
[ 1978.403072] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1978.403076] ata1.01: hard resetting link
[ 1978.722976] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1978.722980] ata1.02: hard resetting link
[ 1979.042879] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1979.042883] ata1.03: hard resetting link
[ 1979.362782] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1979.362786] ata1.04: hard resetting link
[ 1979.682683] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1979.682687] ata1.05: hard resetting link
[ 1980.002584] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1980.002588] ata1.06: hard resetting link
[ 1980.322487] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1980.322604] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.322608] ata1.00: revalidation failed (errno=-5)
[ 1980.322739] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.322743] ata1.01: revalidation failed (errno=-5)
[ 1980.322872] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.322875] ata1.02: revalidation failed (errno=-5)
[ 1980.343060] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.343210] ata1.05: device is on DMA blacklist, disabling DMA
[ 1980.343365] ata1.05: configured for PIO4
[ 1980.343369] ata1: failed to recover some devices, retrying in 5 secs
[ 1985.344781] ata1.00: hard resetting link
[ 1985.664869] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1985.664873] ata1.01: hard resetting link
[ 1985.984773] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1985.984777] ata1.02: hard resetting link
[ 1986.304675] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1986.304679] ata1.03: hard resetting link
[ 1986.624578] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1986.626801] ata1.00: configured for UDMA/100
[ 1986.629042] ata1.01: configured for UDMA/100
[ 1986.733022] ata1.02: configured for UDMA/100
[ 1986.733121] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1986.733125] ata1: failed to recover some devices, retrying in 5 secs
[ 1991.734842] ata1.03: hard resetting link
[ 1992.054930] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1992.055059] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1992.055063] ata1: failed to recover some devices, retrying in 5 secs
[ 1997.057228] ata1.03: hard resetting link
[ 1997.377315] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1997.377599] ata1: EH complete
[ 1997.377625] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377637] sd 1:0:0:0: [sdb] Write Protect is off
[ 1997.377640] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1997.377653] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377668] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377676] sd 1:1:0:0: [sdc] Write Protect is off
[ 1997.377679] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1997.377690] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377704] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377712] sd 1:2:0:0: [sdd] Write Protect is off
[ 1997.377715] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1997.377726] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377740] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1997.377748] sd 1:5:0:0: [sdf] Write Protect is off
[ 1997.377750] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1997.377762] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377775] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377782] sd 1:0:0:0: [sdb] Write Protect is off
[ 1997.377785] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1997.377796] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377809] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377816] sd 1:1:0:0: [sdc] Write Protect is off
[ 1997.377819] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1997.377830] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377843] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377850] sd 1:2:0:0: [sdd] Write Protect is off
[ 1997.377853] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1997.377865] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377877] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1997.377884] sd 1:5:0:0: [sdf] Write Protect is off
[ 1997.377887] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1997.377899] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[-- Attachment #8: 7_PlugUnplug.log --]
[-- Type: text/plain, Size: 31313 bytes --]
nk up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.260036] ata1.02: hard resetting link
[ 1263.579935] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.579939] ata1.03: hard resetting link
[ 1263.899837] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1263.902118] ata1.00: configured for UDMA/100
[ 1263.904377] ata1.01: configured for UDMA/100
[ 1264.006169] ata1.02: configured for UDMA/100
[ 1264.006262] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1264.006266] ata1: failed to recover some devices, retrying in 5 secs
[ 1269.006103] ata1.03: hard resetting link
[ 1269.326192] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1269.326294] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1269.326298] ata1: failed to recover some devices, retrying in 5 secs
[ 1274.328494] ata1.03: hard resetting link
[ 1274.648577] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1274.648860] ata1: EH complete
[ 1274.648888] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648900] sd 1:0:0:0: [sdb] Write Protect is off
[ 1274.648904] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1274.648917] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.648933] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648941] sd 1:1:0:0: [sdc] Write Protect is off
[ 1274.648944] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1274.648955] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.648969] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.648976] sd 1:2:0:0: [sdd] Write Protect is off
[ 1274.648979] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1274.648991] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649004] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1274.649012] sd 1:5:0:0: [sdf] Write Protect is off
[ 1274.649014] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1274.649026] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649039] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649047] sd 1:0:0:0: [sdb] Write Protect is off
[ 1274.649049] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1274.649061] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649073] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649081] sd 1:1:0:0: [sdc] Write Protect is off
[ 1274.649084] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1274.649095] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649108] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1274.649115] sd 1:2:0:0: [sdd] Write Protect is off
[ 1274.649118] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1274.649129] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1274.649142] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1274.649149] sd 1:5:0:0: [sdf] Write Protect is off
[ 1274.649152] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1274.649164] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1568.422342] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1568.422348] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1568.422351] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1568.422354] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1568.422357] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1568.422360] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1568.422363] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1568.422368] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1568.422371] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1568.422375] ata1: SError: { 10B8B }
[ 1568.422380] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422385] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422390] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422396] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422401] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422406] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422411] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1568.422418] ata1.15: hard resetting link
[ 1573.513729] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1573.765647] ata1.15: qc timeout (cmd 0xe4)
[ 1573.765655] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1573.765658] ata1.15: PMP revalidation failed (errno=-5)
[ 1573.765661] ata1.15: retrying hardreset in 5 secs
[ 1578.768128] ata1.15: hard resetting link
[ 1583.862588] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1584.114506] ata1.15: qc timeout (cmd 0xe4)
[ 1584.114513] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1584.114516] ata1.15: PMP revalidation failed (errno=-5)
[ 1584.114520] ata1.15: retrying hardreset in 5 secs
[ 1589.116988] ata1.15: hard resetting link
[ 1594.211450] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1594.463368] ata1.15: qc timeout (cmd 0xe4)
[ 1594.463375] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1594.463378] ata1.15: PMP revalidation failed (errno=-5)
[ 1594.463382] ata1.15: retrying hardreset in 5 secs
[ 1599.465849] ata1.15: hard resetting link
[ 1604.560308] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1604.812227] ata1.15: qc timeout (cmd 0xe4)
[ 1604.812234] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1604.812237] ata1.15: PMP revalidation failed (errno=-5)
[ 1604.812241] ata1.15: retrying hardreset in 5 secs
[ 1609.814709] ata1.15: hard resetting link
[ 1612.741831] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1612.742041] ata1.00: hard resetting link
[ 1613.061909] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1613.061913] ata1.01: hard resetting link
[ 1613.381812] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1613.381816] ata1.02: hard resetting link
[ 1613.701716] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1613.701720] ata1.03: hard resetting link
[ 1614.021621] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1614.021624] ata1.04: hard resetting link
[ 1614.341521] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1614.341524] ata1.05: hard resetting link
[ 1614.661422] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1614.661426] ata1.06: hard resetting link
[ 1614.981331] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1614.981438] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1614.981442] ata1.00: revalidation failed (errno=-5)
[ 1614.981572] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1614.981575] ata1.01: revalidation failed (errno=-5)
[ 1614.981703] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1614.981706] ata1.02: revalidation failed (errno=-5)
[ 1615.001891] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1615.002073] ata1.05: device is on DMA blacklist, disabling DMA
[ 1615.002229] ata1.05: configured for PIO4
[ 1615.002232] ata1: failed to recover some devices, retrying in 5 secs
[ 1620.003619] ata1.00: hard resetting link
[ 1620.323706] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1620.323710] ata1.01: hard resetting link
[ 1620.643612] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1620.643616] ata1.02: hard resetting link
[ 1620.963513] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1620.963517] ata1.03: hard resetting link
[ 1621.283416] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1621.285731] ata1.00: configured for UDMA/100
[ 1621.287984] ata1.01: configured for UDMA/100
[ 1621.289160] ata1.02: serial number mismatch ' 3NF1H4DW' != ' 3NF1JSWM'
[ 1621.289165] ata1.02: revalidation failed (errno=-19)
[ 1621.289287] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1621.289290] ata1: failed to recover some devices, retrying in 5 secs
[ 1626.289712] ata1.02: hard resetting link
[ 1626.609800] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1626.609804] ata1.03: hard resetting link
[ 1626.929703] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1626.930885] ata1.02: serial number mismatch ' 3NF1H4DW' != ' 3NF1JSWM'
[ 1626.930889] ata1.02: revalidation failed (errno=-19)
[ 1626.930892] ata1.02: disabled
[ 1626.931064] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1626.931068] ata1: failed to recover some devices, retrying in 5 secs
[ 1631.932005] ata1.02: hard resetting link
[ 1632.252089] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1632.252094] ata1.03: hard resetting link
[ 1632.571990] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1632.619011] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 1632.619015] ata1.02: 586072368 sectors, multi 0: LBA48
[ 1632.619019] ata1.02: applying bridge limits
[ 1632.677283] ata1.02: configured for UDMA/100
[ 1632.677559] ata1: EH complete
[ 1632.677586] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677598] sd 1:0:0:0: [sdb] Write Protect is off
[ 1632.677602] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1632.677615] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677630] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677638] sd 1:1:0:0: [sdc] Write Protect is off
[ 1632.677641] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1632.677652] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677666] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1632.677674] sd 1:5:0:0: [sdf] Write Protect is off
[ 1632.677677] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1632.677688] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677701] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677708] sd 1:0:0:0: [sdb] Write Protect is off
[ 1632.677711] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1632.677722] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677735] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.677742] sd 1:1:0:0: [sdc] Write Protect is off
[ 1632.677745] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1632.677756] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677769] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1632.677776] sd 1:5:0:0: [sdf] Write Protect is off
[ 1632.677779] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1632.677790] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.677796] ata1.02: detaching (SCSI 1:2:0:0)
[ 1632.677972] sd 1:2:0:0: [sdd] Synchronizing SCSI cache
[ 1632.701650] sd 1:2:0:0: [sdd] Stopping disk
[ 1632.701883] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 1632.701973] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.701993] sd 1:2:0:0: [sdd] Write Protect is off
[ 1632.701997] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1632.702148] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.702209] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1632.702227] sd 1:2:0:0: [sdd] Write Protect is off
[ 1632.702230] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1632.702257] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1632.702261] sdd: sdd1
[ 1633.333656] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 1633.333704] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 1768.255041] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1768.255047] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1768.255050] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1768.255053] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1768.255056] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1768.255059] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1768.255062] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1768.255066] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1768.255070] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1768.255074] ata1: SError: { 10B8B }
[ 1768.255078] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255084] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255089] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255094] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255099] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255104] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255110] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1768.255117] ata1.15: hard resetting link
[ 1773.349102] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1773.601020] ata1.15: qc timeout (cmd 0xe4)
[ 1773.601028] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1773.601031] ata1.15: PMP revalidation failed (errno=-5)
[ 1773.601034] ata1.15: retrying hardreset in 5 secs
[ 1778.603503] ata1.15: hard resetting link
[ 1783.697963] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1783.949880] ata1.15: qc timeout (cmd 0xe4)
[ 1783.949888] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1783.949891] ata1.15: PMP revalidation failed (errno=-5)
[ 1783.949894] ata1.15: retrying hardreset in 5 secs
[ 1788.952363] ata1.15: hard resetting link
[ 1791.151705] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1791.151910] ata1.00: hard resetting link
[ 1791.471785] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1791.471789] ata1.01: hard resetting link
[ 1791.791689] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1791.791693] ata1.02: hard resetting link
[ 1792.111591] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1792.111595] ata1.03: hard resetting link
[ 1792.431493] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1792.431497] ata1.04: hard resetting link
[ 1792.751397] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1792.751400] ata1.05: hard resetting link
[ 1793.071297] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1793.071300] ata1.06: hard resetting link
[ 1793.391206] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1793.393501] ata1.00: configured for UDMA/100
[ 1793.395703] ata1.01: configured for UDMA/100
[ 1793.395805] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1793.395809] ata1.02: revalidation failed (errno=-5)
[ 1793.415996] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1793.416141] ata1.05: device is on DMA blacklist, disabling DMA
[ 1793.416285] ata1.05: configured for PIO4
[ 1793.416288] ata1: failed to recover some devices, retrying in 5 secs
[ 1798.417497] ata1.02: hard resetting link
[ 1798.737581] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1798.737585] ata1.03: hard resetting link
[ 1799.057481] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1799.165478] ata1.02: configured for UDMA/100
[ 1799.165534] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1799.165538] ata1: failed to recover some devices, retrying in 5 secs
[ 1804.167747] ata1.03: hard resetting link
[ 1804.487836] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1804.487893] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1804.487897] ata1: failed to recover some devices, retrying in 5 secs
[ 1809.490138] ata1.03: hard resetting link
[ 1809.810221] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1809.810543] ata1: EH complete
[ 1809.810584] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810596] sd 1:0:0:0: [sdb] Write Protect is off
[ 1809.810599] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1809.810612] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810628] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810636] sd 1:1:0:0: [sdc] Write Protect is off
[ 1809.810639] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1809.810650] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810664] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810672] sd 1:2:0:0: [sdd] Write Protect is off
[ 1809.810675] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1809.810686] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810699] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1809.810707] sd 1:5:0:0: [sdf] Write Protect is off
[ 1809.810710] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1809.810721] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810734] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810742] sd 1:0:0:0: [sdb] Write Protect is off
[ 1809.810744] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1809.810756] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810768] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810775] sd 1:1:0:0: [sdc] Write Protect is off
[ 1809.810778] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1809.810789] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810802] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810809] sd 1:2:0:0: [sdd] Write Protect is off
[ 1809.810812] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1809.810823] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810931] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1809.810939] sd 1:5:0:0: [sdf] Write Protect is off
[ 1809.810941] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1809.810953] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1962.834896] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1962.834903] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1962.834906] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1962.834909] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1962.834912] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1962.834915] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1962.834918] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1962.834923] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1962.834926] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1962.834930] ata1: SError: { 10B8B }
[ 1962.834935] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834940] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834945] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834950] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834955] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834961] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834966] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834973] ata1.15: hard resetting link
[ 1967.926071] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1968.177988] ata1.15: qc timeout (cmd 0xe4)
[ 1968.177996] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1968.177999] ata1.15: PMP revalidation failed (errno=-5)
[ 1968.178002] ata1.15: retrying hardreset in 5 secs
[ 1973.180470] ata1.15: hard resetting link
[ 1978.082992] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1978.083197] ata1.00: hard resetting link
[ 1978.403072] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1978.403076] ata1.01: hard resetting link
[ 1978.722976] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1978.722980] ata1.02: hard resetting link
[ 1979.042879] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1979.042883] ata1.03: hard resetting link
[ 1979.362782] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1979.362786] ata1.04: hard resetting link
[ 1979.682683] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1979.682687] ata1.05: hard resetting link
[ 1980.002584] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1980.002588] ata1.06: hard resetting link
[ 1980.322487] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1980.322604] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.322608] ata1.00: revalidation failed (errno=-5)
[ 1980.322739] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.322743] ata1.01: revalidation failed (errno=-5)
[ 1980.322872] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.322875] ata1.02: revalidation failed (errno=-5)
[ 1980.343060] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.343210] ata1.05: device is on DMA blacklist, disabling DMA
[ 1980.343365] ata1.05: configured for PIO4
[ 1980.343369] ata1: failed to recover some devices, retrying in 5 secs
[ 1985.344781] ata1.00: hard resetting link
[ 1985.664869] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1985.664873] ata1.01: hard resetting link
[ 1985.984773] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1985.984777] ata1.02: hard resetting link
[ 1986.304675] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1986.304679] ata1.03: hard resetting link
[ 1986.624578] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1986.626801] ata1.00: configured for UDMA/100
[ 1986.629042] ata1.01: configured for UDMA/100
[ 1986.733022] ata1.02: configured for UDMA/100
[ 1986.733121] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1986.733125] ata1: failed to recover some devices, retrying in 5 secs
[ 1991.734842] ata1.03: hard resetting link
[ 1992.054930] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1992.055059] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1992.055063] ata1: failed to recover some devices, retrying in 5 secs
[ 1997.057228] ata1.03: hard resetting link
[ 1997.377315] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1997.377599] ata1: EH complete
[ 1997.377625] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377637] sd 1:0:0:0: [sdb] Write Protect is off
[ 1997.377640] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1997.377653] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377668] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377676] sd 1:1:0:0: [sdc] Write Protect is off
[ 1997.377679] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1997.377690] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377704] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377712] sd 1:2:0:0: [sdd] Write Protect is off
[ 1997.377715] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1997.377726] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377740] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1997.377748] sd 1:5:0:0: [sdf] Write Protect is off
[ 1997.377750] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1997.377762] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377775] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377782] sd 1:0:0:0: [sdb] Write Protect is off
[ 1997.377785] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1997.377796] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377809] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377816] sd 1:1:0:0: [sdc] Write Protect is off
[ 1997.377819] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1997.377830] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377843] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377850] sd 1:2:0:0: [sdd] Write Protect is off
[ 1997.377853] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1997.377865] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377877] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1997.377884] sd 1:5:0:0: [sdf] Write Protect is off
[ 1997.377887] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1997.377899] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2194.972229] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2194.972235] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2194.972238] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2194.972241] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2194.972244] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2194.972247] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2194.972250] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2194.972254] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2194.972258] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 2194.972262] ata1: SError: { 10B8B }
[ 2194.972267] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972272] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972277] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972282] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972287] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972292] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972298] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972306] ata1.15: hard resetting link
[ 2200.063645] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2200.315563] ata1.15: qc timeout (cmd 0xe4)
[ 2200.315571] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2200.315574] ata1.15: PMP revalidation failed (errno=-5)
[ 2200.315577] ata1.15: retrying hardreset in 5 secs
[ 2205.318045] ata1.15: hard resetting link
[ 2210.412505] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2210.664423] ata1.15: qc timeout (cmd 0xe4)
[ 2210.664430] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2210.664433] ata1.15: PMP revalidation failed (errno=-5)
[ 2210.664437] ata1.15: retrying hardreset in 5 secs
[ 2215.666905] ata1.15: hard resetting link
[ 2217.866247] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 2217.866481] ata1.00: hard resetting link
[ 2218.186327] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2218.186331] ata1.01: hard resetting link
[ 2218.506230] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2218.506234] ata1.02: hard resetting link
[ 2218.826133] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2218.826137] ata1.03: hard resetting link
[ 2219.146037] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2219.146041] ata1.04: hard resetting link
[ 2219.465939] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 2219.465943] ata1.05: hard resetting link
[ 2219.785841] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 2219.785844] ata1.06: hard resetting link
[ 2220.105744] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2220.107998] ata1.00: configured for UDMA/100
[ 2220.110200] ata1.01: configured for UDMA/100
[ 2220.212693] ata1.02: configured for UDMA/100
[ 2220.260388] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 2220.260392] ata1.03: 586072368 sectors, multi 0: LBA48
[ 2220.260395] ata1.03: applying bridge limits
[ 2220.326830] ata1.03: configured for UDMA/100
[ 2220.326935] ata1.05: device is on DMA blacklist, disabling DMA
[ 2220.327039] ata1.05: configured for PIO4
[ 2220.327308] ata1: EH complete
[ 2220.327332] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327343] sd 1:0:0:0: [sdb] Write Protect is off
[ 2220.327347] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2220.327359] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327374] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327382] sd 1:1:0:0: [sdc] Write Protect is off
[ 2220.327384] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2220.327396] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327409] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327417] sd 1:2:0:0: [sdd] Write Protect is off
[ 2220.327420] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2220.327431] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327445] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2220.327452] sd 1:5:0:0: [sdf] Write Protect is off
[ 2220.327455] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2220.327467] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327479] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327487] sd 1:0:0:0: [sdb] Write Protect is off
[ 2220.327490] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2220.327501] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327513] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327521] sd 1:1:0:0: [sdc] Write Protect is off
[ 2220.327524] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2220.327535] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327548] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327555] sd 1:2:0:0: [sdd] Write Protect is off
[ 2220.327558] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2220.327569] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327582] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2220.327589] sd 1:5:0:0: [sdf] Write Protect is off
[ 2220.327592] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2220.327603] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327674] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 2220.328136] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.328145] sd 1:3:0:0: [sde] Write Protect is off
[ 2220.328148] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2220.328160] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.328204] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.328212] sd 1:3:0:0: [sde] Write Protect is off
[ 2220.328215] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2220.328622] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.328627] sde: sde1
[ 2220.366475] sd 1:3:0:0: [sde] Attached SCSI disk
[ 2220.366525] sd 1:3:0:0: Attached scsi generic sg5 type 0
[-- Attachment #9: 8_PowerOnOffTwice.log --]
[-- Type: text/plain, Size: 31319 bytes --]
[ 1788.952363] ata1.15: hard resetting link
[ 1791.151705] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1791.151910] ata1.00: hard resetting link
[ 1791.471785] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1791.471789] ata1.01: hard resetting link
[ 1791.791689] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1791.791693] ata1.02: hard resetting link
[ 1792.111591] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1792.111595] ata1.03: hard resetting link
[ 1792.431493] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1792.431497] ata1.04: hard resetting link
[ 1792.751397] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1792.751400] ata1.05: hard resetting link
[ 1793.071297] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1793.071300] ata1.06: hard resetting link
[ 1793.391206] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1793.393501] ata1.00: configured for UDMA/100
[ 1793.395703] ata1.01: configured for UDMA/100
[ 1793.395805] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1793.395809] ata1.02: revalidation failed (errno=-5)
[ 1793.415996] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1793.416141] ata1.05: device is on DMA blacklist, disabling DMA
[ 1793.416285] ata1.05: configured for PIO4
[ 1793.416288] ata1: failed to recover some devices, retrying in 5 secs
[ 1798.417497] ata1.02: hard resetting link
[ 1798.737581] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1798.737585] ata1.03: hard resetting link
[ 1799.057481] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1799.165478] ata1.02: configured for UDMA/100
[ 1799.165534] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1799.165538] ata1: failed to recover some devices, retrying in 5 secs
[ 1804.167747] ata1.03: hard resetting link
[ 1804.487836] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1804.487893] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1804.487897] ata1: failed to recover some devices, retrying in 5 secs
[ 1809.490138] ata1.03: hard resetting link
[ 1809.810221] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1809.810543] ata1: EH complete
[ 1809.810584] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810596] sd 1:0:0:0: [sdb] Write Protect is off
[ 1809.810599] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1809.810612] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810628] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810636] sd 1:1:0:0: [sdc] Write Protect is off
[ 1809.810639] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1809.810650] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810664] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810672] sd 1:2:0:0: [sdd] Write Protect is off
[ 1809.810675] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1809.810686] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810699] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1809.810707] sd 1:5:0:0: [sdf] Write Protect is off
[ 1809.810710] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1809.810721] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810734] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810742] sd 1:0:0:0: [sdb] Write Protect is off
[ 1809.810744] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1809.810756] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810768] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810775] sd 1:1:0:0: [sdc] Write Protect is off
[ 1809.810778] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1809.810789] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810802] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1809.810809] sd 1:2:0:0: [sdd] Write Protect is off
[ 1809.810812] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1809.810823] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1809.810931] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1809.810939] sd 1:5:0:0: [sdf] Write Protect is off
[ 1809.810941] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1809.810953] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1962.834896] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 1962.834903] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 1962.834906] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 1962.834909] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 1962.834912] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 1962.834915] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 1962.834918] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 1962.834923] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 1962.834926] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 1962.834930] ata1: SError: { 10B8B }
[ 1962.834935] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834940] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834945] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834950] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834955] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834961] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834966] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1962.834973] ata1.15: hard resetting link
[ 1967.926071] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 1968.177988] ata1.15: qc timeout (cmd 0xe4)
[ 1968.177996] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 1968.177999] ata1.15: PMP revalidation failed (errno=-5)
[ 1968.178002] ata1.15: retrying hardreset in 5 secs
[ 1973.180470] ata1.15: hard resetting link
[ 1978.082992] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 1978.083197] ata1.00: hard resetting link
[ 1978.403072] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1978.403076] ata1.01: hard resetting link
[ 1978.722976] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1978.722980] ata1.02: hard resetting link
[ 1979.042879] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1979.042883] ata1.03: hard resetting link
[ 1979.362782] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1979.362786] ata1.04: hard resetting link
[ 1979.682683] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 1979.682687] ata1.05: hard resetting link
[ 1980.002584] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 1980.002588] ata1.06: hard resetting link
[ 1980.322487] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1980.322604] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.322608] ata1.00: revalidation failed (errno=-5)
[ 1980.322739] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.322743] ata1.01: revalidation failed (errno=-5)
[ 1980.322872] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.322875] ata1.02: revalidation failed (errno=-5)
[ 1980.343060] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1980.343210] ata1.05: device is on DMA blacklist, disabling DMA
[ 1980.343365] ata1.05: configured for PIO4
[ 1980.343369] ata1: failed to recover some devices, retrying in 5 secs
[ 1985.344781] ata1.00: hard resetting link
[ 1985.664869] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1985.664873] ata1.01: hard resetting link
[ 1985.984773] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1985.984777] ata1.02: hard resetting link
[ 1986.304675] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1986.304679] ata1.03: hard resetting link
[ 1986.624578] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1986.626801] ata1.00: configured for UDMA/100
[ 1986.629042] ata1.01: configured for UDMA/100
[ 1986.733022] ata1.02: configured for UDMA/100
[ 1986.733121] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1986.733125] ata1: failed to recover some devices, retrying in 5 secs
[ 1991.734842] ata1.03: hard resetting link
[ 1992.054930] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1992.055059] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 1992.055063] ata1: failed to recover some devices, retrying in 5 secs
[ 1997.057228] ata1.03: hard resetting link
[ 1997.377315] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1997.377599] ata1: EH complete
[ 1997.377625] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377637] sd 1:0:0:0: [sdb] Write Protect is off
[ 1997.377640] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1997.377653] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377668] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377676] sd 1:1:0:0: [sdc] Write Protect is off
[ 1997.377679] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1997.377690] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377704] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377712] sd 1:2:0:0: [sdd] Write Protect is off
[ 1997.377715] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1997.377726] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377740] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1997.377748] sd 1:5:0:0: [sdf] Write Protect is off
[ 1997.377750] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1997.377762] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377775] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377782] sd 1:0:0:0: [sdb] Write Protect is off
[ 1997.377785] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1997.377796] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377809] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377816] sd 1:1:0:0: [sdc] Write Protect is off
[ 1997.377819] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1997.377830] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377843] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 1997.377850] sd 1:2:0:0: [sdd] Write Protect is off
[ 1997.377853] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 1997.377865] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1997.377877] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 1997.377884] sd 1:5:0:0: [sdf] Write Protect is off
[ 1997.377887] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 1997.377899] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2194.972229] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2194.972235] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2194.972238] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2194.972241] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2194.972244] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2194.972247] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2194.972250] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2194.972254] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2194.972258] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 2194.972262] ata1: SError: { 10B8B }
[ 2194.972267] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972272] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972277] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972282] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972287] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972292] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972298] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2194.972306] ata1.15: hard resetting link
[ 2200.063645] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2200.315563] ata1.15: qc timeout (cmd 0xe4)
[ 2200.315571] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2200.315574] ata1.15: PMP revalidation failed (errno=-5)
[ 2200.315577] ata1.15: retrying hardreset in 5 secs
[ 2205.318045] ata1.15: hard resetting link
[ 2210.412505] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2210.664423] ata1.15: qc timeout (cmd 0xe4)
[ 2210.664430] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2210.664433] ata1.15: PMP revalidation failed (errno=-5)
[ 2210.664437] ata1.15: retrying hardreset in 5 secs
[ 2215.666905] ata1.15: hard resetting link
[ 2217.866247] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 2217.866481] ata1.00: hard resetting link
[ 2218.186327] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2218.186331] ata1.01: hard resetting link
[ 2218.506230] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2218.506234] ata1.02: hard resetting link
[ 2218.826133] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2218.826137] ata1.03: hard resetting link
[ 2219.146037] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2219.146041] ata1.04: hard resetting link
[ 2219.465939] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 2219.465943] ata1.05: hard resetting link
[ 2219.785841] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 2219.785844] ata1.06: hard resetting link
[ 2220.105744] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2220.107998] ata1.00: configured for UDMA/100
[ 2220.110200] ata1.01: configured for UDMA/100
[ 2220.212693] ata1.02: configured for UDMA/100
[ 2220.260388] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 2220.260392] ata1.03: 586072368 sectors, multi 0: LBA48
[ 2220.260395] ata1.03: applying bridge limits
[ 2220.326830] ata1.03: configured for UDMA/100
[ 2220.326935] ata1.05: device is on DMA blacklist, disabling DMA
[ 2220.327039] ata1.05: configured for PIO4
[ 2220.327308] ata1: EH complete
[ 2220.327332] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327343] sd 1:0:0:0: [sdb] Write Protect is off
[ 2220.327347] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2220.327359] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327374] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327382] sd 1:1:0:0: [sdc] Write Protect is off
[ 2220.327384] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2220.327396] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327409] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327417] sd 1:2:0:0: [sdd] Write Protect is off
[ 2220.327420] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2220.327431] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327445] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2220.327452] sd 1:5:0:0: [sdf] Write Protect is off
[ 2220.327455] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2220.327467] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327479] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327487] sd 1:0:0:0: [sdb] Write Protect is off
[ 2220.327490] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2220.327501] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327513] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327521] sd 1:1:0:0: [sdc] Write Protect is off
[ 2220.327524] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2220.327535] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327548] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.327555] sd 1:2:0:0: [sdd] Write Protect is off
[ 2220.327558] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2220.327569] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327582] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2220.327589] sd 1:5:0:0: [sdf] Write Protect is off
[ 2220.327592] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2220.327603] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327674] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 2220.328136] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.328145] sd 1:3:0:0: [sde] Write Protect is off
[ 2220.328148] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2220.328160] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.328204] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.328212] sd 1:3:0:0: [sde] Write Protect is off
[ 2220.328215] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2220.328622] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.328627] sde: sde1
[ 2220.366475] sd 1:3:0:0: [sde] Attached SCSI disk
[ 2220.366525] sd 1:3:0:0: Attached scsi generic sg5 type 0
[ 2327.669606] ata1.15: limiting speed to PIO0
[ 2327.669613] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2327.669617] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2327.669620] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2327.669623] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2327.669626] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2327.669629] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2327.669632] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2327.669636] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2327.669639] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 2327.669643] ata1: SError: { 10B8B }
[ 2327.669648] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669653] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669659] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669664] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669669] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669674] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669679] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669687] ata1.15: hard resetting link
[ 2332.763389] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2333.015306] ata1.15: qc timeout (cmd 0xe4)
[ 2333.015314] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2333.015318] ata1.15: PMP revalidation failed (errno=-5)
[ 2333.015321] ata1.15: retrying hardreset in 5 secs
[ 2338.017789] ata1.15: hard resetting link
[ 2343.112248] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2343.212225] ata1.15: failed to read PMP GSCR[0] (Emask=0x100)
[ 2343.212229] ata1.15: PMP revalidation failed (errno=-5)
[ 2343.212233] ata1.15: retrying hardreset in 5 secs
[ 2348.214695] ata1.15: hard resetting link
[ 2350.414038] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 2350.414247] ata1.00: hard resetting link
[ 2350.734118] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2350.734122] ata1.01: hard resetting link
[ 2351.054021] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2351.054025] ata1.02: hard resetting link
[ 2351.373925] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2351.373933] ata1.03: hard resetting link
[ 2351.693827] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2351.693831] ata1.04: hard resetting link
[ 2352.013729] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 2352.013733] ata1.05: hard resetting link
[ 2352.333630] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 2352.333634] ata1.06: hard resetting link
[ 2352.653540] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2352.655782] ata1.00: configured for UDMA/100
[ 2352.657980] ata1.01: configured for UDMA/100
[ 2352.764096] ata1.02: configured for UDMA/100
[ 2352.861654] ata1.03: configured for UDMA/100
[ 2352.861763] ata1.05: device is on DMA blacklist, disabling DMA
[ 2352.861871] ata1.05: configured for PIO4
[ 2352.862086] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
[ 2352.862090] ata1.15: irq_stat 0x00800080, device exchanged
[ 2352.862360] ata1: EH complete
[ 2352.862385] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862397] sd 1:0:0:0: [sdb] Write Protect is off
[ 2352.862400] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2352.862414] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862428] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862436] sd 1:1:0:0: [sdc] Write Protect is off
[ 2352.862439] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2352.862450] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862464] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862472] sd 1:2:0:0: [sdd] Write Protect is off
[ 2352.862475] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2352.862486] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862499] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862507] sd 1:3:0:0: [sde] Write Protect is off
[ 2352.862510] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2352.862521] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862535] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2352.862542] sd 1:5:0:0: [sdf] Write Protect is off
[ 2352.862545] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2352.862557] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862569] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862577] sd 1:0:0:0: [sdb] Write Protect is off
[ 2352.862580] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2352.862591] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862604] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862611] sd 1:1:0:0: [sdc] Write Protect is off
[ 2352.862614] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2352.862626] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862638] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862646] sd 1:2:0:0: [sdd] Write Protect is off
[ 2352.862649] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2352.862660] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862673] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862680] sd 1:3:0:0: [sde] Write Protect is off
[ 2352.862683] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2352.862694] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862706] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2352.862714] sd 1:5:0:0: [sdf] Write Protect is off
[ 2352.862717] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2352.862728] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2467.824811] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2467.824817] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2467.824820] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2467.824823] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2467.824826] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2467.824829] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2467.824832] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2467.824837] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2467.824840] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 2467.824844] ata1: SError: { 10B8B }
[ 2467.824849] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824854] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824859] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824864] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824870] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824875] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824880] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824887] ata1.15: hard resetting link
[ 2472.916873] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2473.168790] ata1.15: qc timeout (cmd 0xe4)
[ 2473.168799] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2473.168802] ata1.15: PMP revalidation failed (errno=-5)
[ 2473.168805] ata1.15: retrying hardreset in 5 secs
[ 2478.171271] ata1.15: hard resetting link
[ 2483.265729] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2483.517647] ata1.15: qc timeout (cmd 0xe4)
[ 2483.517655] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2483.517658] ata1.15: PMP revalidation failed (errno=-5)
[ 2483.517662] ata1.15: retrying hardreset in 5 secs
[ 2488.520130] ata1.15: hard resetting link
[ 2490.719472] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 2490.719682] ata1.00: hard resetting link
[ 2491.039551] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2491.039554] ata1.01: hard resetting link
[ 2491.359454] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2491.359458] ata1.02: hard resetting link
[ 2491.679359] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2491.679363] ata1.03: hard resetting link
[ 2491.999261] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2491.999265] ata1.04: hard resetting link
[ 2492.319165] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 2492.319168] ata1.05: hard resetting link
[ 2492.639066] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 2492.639070] ata1.06: hard resetting link
[ 2492.958971] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2492.961345] ata1.00: configured for UDMA/100
[ 2492.963537] ata1.01: configured for UDMA/100
[ 2492.963689] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2492.963693] ata1.02: revalidation failed (errno=-5)
[ 2492.963824] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2492.963828] ata1.03: revalidation failed (errno=-5)
[ 2492.963962] ata1.05: device is on DMA blacklist, disabling DMA
[ 2492.964068] ata1.05: configured for PIO4
[ 2492.964071] ata1: failed to recover some devices, retrying in 5 secs
[ 2497.965270] ata1.02: hard resetting link
[ 2498.285353] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2498.285358] ata1.03: hard resetting link
[ 2498.605256] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2498.710753] ata1.02: configured for UDMA/100
[ 2498.710857] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2498.710861] ata1.03: revalidation failed (errno=-5)
[ 2498.710865] ata1: failed to recover some devices, retrying in 5 secs
[ 2503.711527] ata1.03: hard resetting link
[ 2504.031610] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2504.031731] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2504.031735] ata1.03: revalidation failed (errno=-5)
[ 2504.031738] ata1.03: disabled
[ 2504.535271] ata1.03: hard resetting link
[ 2504.855360] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2504.855415] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2504.855419] ata1: failed to recover some devices, retrying in 5 secs
[ 2509.857662] ata1.03: hard resetting link
[ 2510.177746] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2510.177809] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2510.177814] ata1: failed to recover some devices, retrying in 5 secs
[ 2515.180048] ata1.03: hard resetting link
[ 2515.500132] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2515.500195] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2515.500199] ata1: failed to recover some devices, retrying in 5 secs
[ 2520.502428] ata1.03: hard resetting link
[ 2520.822515] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2520.822793] ata1: EH complete
[ 2520.822822] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822834] sd 1:0:0:0: [sdb] Write Protect is off
[ 2520.822837] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2520.822850] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822866] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822874] sd 1:1:0:0: [sdc] Write Protect is off
[ 2520.822877] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2520.822888] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822901] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822910] sd 1:2:0:0: [sdd] Write Protect is off
[ 2520.822912] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2520.822924] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822937] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2520.822944] sd 1:5:0:0: [sdf] Write Protect is off
[ 2520.822947] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2520.822959] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822971] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822979] sd 1:0:0:0: [sdb] Write Protect is off
[ 2520.822982] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2520.822993] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823005] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.823012] sd 1:1:0:0: [sdc] Write Protect is off
[ 2520.823015] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2520.823026] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823039] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.823046] sd 1:2:0:0: [sdd] Write Protect is off
[ 2520.823049] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2520.823060] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823073] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2520.823080] sd 1:5:0:0: [sdf] Write Protect is off
[ 2520.823083] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2520.823094] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823100] ata1.03: detaching (SCSI 1:3:0:0)
[ 2520.823274] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 2520.823738] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 2520.823742] sd 1:3:0:0: [sde] Stopping disk
[ 2520.824243] sd 1:3:0:0: [sde] START_STOP FAILED
[ 2520.824246] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[-- Attachment #10: 9_OccupyLastPMPPort.log --]
[-- Type: text/plain, Size: 31286 bytes --]
5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.327674] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 2220.328136] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.328145] sd 1:3:0:0: [sde] Write Protect is off
[ 2220.328148] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2220.328160] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.328204] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 2220.328212] sd 1:3:0:0: [sde] Write Protect is off
[ 2220.328215] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2220.328622] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2220.328627] sde: sde1
[ 2220.366475] sd 1:3:0:0: [sde] Attached SCSI disk
[ 2220.366525] sd 1:3:0:0: Attached scsi generic sg5 type 0
[ 2327.669606] ata1.15: limiting speed to PIO0
[ 2327.669613] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2327.669617] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2327.669620] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2327.669623] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2327.669626] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2327.669629] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2327.669632] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2327.669636] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2327.669639] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 2327.669643] ata1: SError: { 10B8B }
[ 2327.669648] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669653] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669659] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669664] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669669] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669674] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669679] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2327.669687] ata1.15: hard resetting link
[ 2332.763389] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2333.015306] ata1.15: qc timeout (cmd 0xe4)
[ 2333.015314] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2333.015318] ata1.15: PMP revalidation failed (errno=-5)
[ 2333.015321] ata1.15: retrying hardreset in 5 secs
[ 2338.017789] ata1.15: hard resetting link
[ 2343.112248] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2343.212225] ata1.15: failed to read PMP GSCR[0] (Emask=0x100)
[ 2343.212229] ata1.15: PMP revalidation failed (errno=-5)
[ 2343.212233] ata1.15: retrying hardreset in 5 secs
[ 2348.214695] ata1.15: hard resetting link
[ 2350.414038] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 2350.414247] ata1.00: hard resetting link
[ 2350.734118] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2350.734122] ata1.01: hard resetting link
[ 2351.054021] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2351.054025] ata1.02: hard resetting link
[ 2351.373925] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2351.373933] ata1.03: hard resetting link
[ 2351.693827] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2351.693831] ata1.04: hard resetting link
[ 2352.013729] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 2352.013733] ata1.05: hard resetting link
[ 2352.333630] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 2352.333634] ata1.06: hard resetting link
[ 2352.653540] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2352.655782] ata1.00: configured for UDMA/100
[ 2352.657980] ata1.01: configured for UDMA/100
[ 2352.764096] ata1.02: configured for UDMA/100
[ 2352.861654] ata1.03: configured for UDMA/100
[ 2352.861763] ata1.05: device is on DMA blacklist, disabling DMA
[ 2352.861871] ata1.05: configured for PIO4
[ 2352.862086] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
[ 2352.862090] ata1.15: irq_stat 0x00800080, device exchanged
[ 2352.862360] ata1: EH complete
[ 2352.862385] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862397] sd 1:0:0:0: [sdb] Write Protect is off
[ 2352.862400] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2352.862414] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862428] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862436] sd 1:1:0:0: [sdc] Write Protect is off
[ 2352.862439] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2352.862450] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862464] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862472] sd 1:2:0:0: [sdd] Write Protect is off
[ 2352.862475] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2352.862486] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862499] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862507] sd 1:3:0:0: [sde] Write Protect is off
[ 2352.862510] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2352.862521] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862535] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2352.862542] sd 1:5:0:0: [sdf] Write Protect is off
[ 2352.862545] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2352.862557] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862569] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862577] sd 1:0:0:0: [sdb] Write Protect is off
[ 2352.862580] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2352.862591] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862604] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862611] sd 1:1:0:0: [sdc] Write Protect is off
[ 2352.862614] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2352.862626] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862638] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862646] sd 1:2:0:0: [sdd] Write Protect is off
[ 2352.862649] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2352.862660] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862673] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 2352.862680] sd 1:3:0:0: [sde] Write Protect is off
[ 2352.862683] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2352.862694] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2352.862706] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2352.862714] sd 1:5:0:0: [sdf] Write Protect is off
[ 2352.862717] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2352.862728] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2467.824811] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2467.824817] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2467.824820] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2467.824823] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2467.824826] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2467.824829] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2467.824832] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2467.824837] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2467.824840] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 2467.824844] ata1: SError: { 10B8B }
[ 2467.824849] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824854] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824859] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824864] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824870] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824875] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824880] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824887] ata1.15: hard resetting link
[ 2472.916873] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2473.168790] ata1.15: qc timeout (cmd 0xe4)
[ 2473.168799] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2473.168802] ata1.15: PMP revalidation failed (errno=-5)
[ 2473.168805] ata1.15: retrying hardreset in 5 secs
[ 2478.171271] ata1.15: hard resetting link
[ 2483.265729] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2483.517647] ata1.15: qc timeout (cmd 0xe4)
[ 2483.517655] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2483.517658] ata1.15: PMP revalidation failed (errno=-5)
[ 2483.517662] ata1.15: retrying hardreset in 5 secs
[ 2488.520130] ata1.15: hard resetting link
[ 2490.719472] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 2490.719682] ata1.00: hard resetting link
[ 2491.039551] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2491.039554] ata1.01: hard resetting link
[ 2491.359454] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2491.359458] ata1.02: hard resetting link
[ 2491.679359] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2491.679363] ata1.03: hard resetting link
[ 2491.999261] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2491.999265] ata1.04: hard resetting link
[ 2492.319165] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 2492.319168] ata1.05: hard resetting link
[ 2492.639066] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 2492.639070] ata1.06: hard resetting link
[ 2492.958971] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2492.961345] ata1.00: configured for UDMA/100
[ 2492.963537] ata1.01: configured for UDMA/100
[ 2492.963689] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2492.963693] ata1.02: revalidation failed (errno=-5)
[ 2492.963824] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2492.963828] ata1.03: revalidation failed (errno=-5)
[ 2492.963962] ata1.05: device is on DMA blacklist, disabling DMA
[ 2492.964068] ata1.05: configured for PIO4
[ 2492.964071] ata1: failed to recover some devices, retrying in 5 secs
[ 2497.965270] ata1.02: hard resetting link
[ 2498.285353] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2498.285358] ata1.03: hard resetting link
[ 2498.605256] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2498.710753] ata1.02: configured for UDMA/100
[ 2498.710857] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2498.710861] ata1.03: revalidation failed (errno=-5)
[ 2498.710865] ata1: failed to recover some devices, retrying in 5 secs
[ 2503.711527] ata1.03: hard resetting link
[ 2504.031610] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2504.031731] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2504.031735] ata1.03: revalidation failed (errno=-5)
[ 2504.031738] ata1.03: disabled
[ 2504.535271] ata1.03: hard resetting link
[ 2504.855360] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2504.855415] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2504.855419] ata1: failed to recover some devices, retrying in 5 secs
[ 2509.857662] ata1.03: hard resetting link
[ 2510.177746] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2510.177809] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2510.177814] ata1: failed to recover some devices, retrying in 5 secs
[ 2515.180048] ata1.03: hard resetting link
[ 2515.500132] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2515.500195] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2515.500199] ata1: failed to recover some devices, retrying in 5 secs
[ 2520.502428] ata1.03: hard resetting link
[ 2520.822515] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2520.822793] ata1: EH complete
[ 2520.822822] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822834] sd 1:0:0:0: [sdb] Write Protect is off
[ 2520.822837] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2520.822850] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822866] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822874] sd 1:1:0:0: [sdc] Write Protect is off
[ 2520.822877] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2520.822888] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822901] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822910] sd 1:2:0:0: [sdd] Write Protect is off
[ 2520.822912] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2520.822924] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822937] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2520.822944] sd 1:5:0:0: [sdf] Write Protect is off
[ 2520.822947] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2520.822959] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822971] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822979] sd 1:0:0:0: [sdb] Write Protect is off
[ 2520.822982] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2520.822993] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823005] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.823012] sd 1:1:0:0: [sdc] Write Protect is off
[ 2520.823015] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2520.823026] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823039] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.823046] sd 1:2:0:0: [sdd] Write Protect is off
[ 2520.823049] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2520.823060] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823073] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2520.823080] sd 1:5:0:0: [sdf] Write Protect is off
[ 2520.823083] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2520.823094] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823100] ata1.03: detaching (SCSI 1:3:0:0)
[ 2520.823274] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 2520.823738] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 2520.823742] sd 1:3:0:0: [sde] Stopping disk
[ 2520.824243] sd 1:3:0:0: [sde] START_STOP FAILED
[ 2520.824246] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 2689.226123] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2689.226129] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2689.226132] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2689.226135] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2689.226138] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2689.226141] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2689.226144] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2689.226148] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2689.226152] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 2689.226156] ata1: SError: { 10B8B }
[ 2689.226161] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226166] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226171] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226176] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226181] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226186] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226192] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226199] ata1.15: hard resetting link
[ 2694.317699] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2694.569617] ata1.15: qc timeout (cmd 0xe4)
[ 2694.569625] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2694.569628] ata1.15: PMP revalidation failed (errno=-5)
[ 2694.569631] ata1.15: retrying hardreset in 5 secs
[ 2699.572098] ata1.15: hard resetting link
[ 2704.666558] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2704.918477] ata1.15: qc timeout (cmd 0xe4)
[ 2704.918484] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2704.918487] ata1.15: PMP revalidation failed (errno=-5)
[ 2704.918491] ata1.15: retrying hardreset in 5 secs
[ 2709.920959] ata1.15: hard resetting link
[ 2715.015418] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2715.267337] ata1.15: qc timeout (cmd 0xe4)
[ 2715.267344] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2715.267347] ata1.15: PMP revalidation failed (errno=-5)
[ 2715.267351] ata1.15: retrying hardreset in 5 secs
[ 2720.269819] ata1.15: hard resetting link
[ 2725.364279] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2725.616196] ata1.15: qc timeout (cmd 0xe4)
[ 2725.616204] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2725.616207] ata1.15: PMP revalidation failed (errno=-5)
[ 2725.616210] ata1.15: retrying hardreset in 5 secs
[ 2730.618679] ata1.15: hard resetting link
[ 2735.713139] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2735.965057] ata1.15: qc timeout (cmd 0xe4)
[ 2735.965064] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2735.965067] ata1.15: PMP revalidation failed (errno=-5)
[ 2735.965070] ata1.15: failed to recover PMP after 5 tries, giving up
[ 2735.965073] ata1.15: Port Multiplier detaching
[ 2735.965081] ata1.00: disabled
[ 2735.965084] ata1.01: disabled
[ 2735.965087] ata1.02: disabled
[ 2735.965089] ata1.05: disabled
[ 2735.965092] ata1.00: disabled
[ 2735.965098] ata1: hard resetting link
[ 2739.308053] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 2739.308243] ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
[ 2739.308453] ata1.00: hard resetting link
[ 2739.628109] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2739.628113] ata1.01: hard resetting link
[ 2739.948009] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2739.948013] ata1.02: hard resetting link
[ 2740.267914] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2740.267918] ata1.03: hard resetting link
[ 2740.587815] ata1.03: SATA link down (SStatus 0 SControl 320)
[ 2740.587819] ata1.04: hard resetting link
[ 2740.907722] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2740.907726] ata1.05: hard resetting link
[ 2741.227621] ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 2741.227624] ata1.06: hard resetting link
[ 2741.547525] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2741.547584] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2741.567765] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2741.587927] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2741.608087] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2741.628249] ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
[ 2741.628252] ata1.05: 640 sectors, multi 1: LBA
[ 2741.628261] ata1.05: device is on DMA blacklist, disabling DMA
[ 2741.628464] ata1.05: configured for PIO4
[ 2741.628468] ata1: failed to recover some devices, retrying in 5 secs
[ 2746.629822] ata1.00: hard resetting link
[ 2746.949886] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2746.949891] ata1.01: hard resetting link
[ 2747.269789] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2747.269793] ata1.02: hard resetting link
[ 2747.589691] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2747.589695] ata1.04: hard resetting link
[ 2747.909595] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2747.910678] ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 2747.910681] ata1.00: 586072368 sectors, multi 0: LBA48
[ 2747.910684] ata1.00: applying bridge limits
[ 2747.911859] ata1.00: configured for UDMA/100
[ 2747.912923] ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 2747.912926] ata1.01: 586072368 sectors, multi 0: LBA48
[ 2747.912929] ata1.01: applying bridge limits
[ 2747.914104] ata1.01: configured for UDMA/100
[ 2747.960737] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 2747.960740] ata1.02: 586072368 sectors, multi 0: LBA48
[ 2747.960743] ata1.02: applying bridge limits
[ 2748.018887] ata1.02: configured for UDMA/100
[ 2748.018981] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2748.019122] ata1.05: device is on DMA blacklist, disabling DMA
[ 2748.019288] ata1.05: configured for PIO4
[ 2748.019291] ata1: failed to recover some devices, retrying in 5 secs
[ 2753.019883] ata1.04: hard resetting link
[ 2753.339948] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2753.342229] ata1.00: configured for UDMA/100
[ 2753.344443] ata1.01: configured for UDMA/100
[ 2753.434140] ata1.02: configured for UDMA/100
[ 2753.434235] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2753.434239] ata1: failed to recover some devices, retrying in 5 secs
[ 2758.434240] ata1.04: hard resetting link
[ 2758.754305] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2758.754564] ata1: EH complete
[ 2758.754572] ata1.00: detaching (SCSI 1:0:0:0)
[ 2758.754749] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 2758.755045] sd 1:0:0:0: [sdb] Stopping disk
[ 2758.755191] ata1.01: detaching (SCSI 1:1:0:0)
[ 2758.755325] sd 1:1:0:0: [sdc] Synchronizing SCSI cache
[ 2758.755839] sd 1:1:0:0: [sdc] Stopping disk
[ 2758.756172] ata1.02: detaching (SCSI 1:2:0:0)
[ 2758.756322] sd 1:2:0:0: [sdd] Synchronizing SCSI cache
[ 2758.756426] sd 1:2:0:0: [sdd] Stopping disk
[ 2758.756533] ata1.05: detaching (SCSI 1:5:0:0)
[ 2758.756655] sd 1:5:0:0: [sdf] Stopping disk
[ 2758.756846] scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 2758.756973] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2758.757000] sd 1:0:0:0: [sdb] Write Protect is off
[ 2758.757003] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2758.757032] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2758.757212] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2758.757237] sd 1:0:0:0: [sdb] Write Protect is off
[ 2758.757240] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2758.757267] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2758.757273] sdb: sdb1
[ 2759.435145] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 2759.435193] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 2759.435522] scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 2759.435611] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2759.435632] sd 1:1:0:0: [sdc] Write Protect is off
[ 2759.435636] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2759.435665] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2759.435719] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2759.435737] sd 1:1:0:0: [sdc] Write Protect is off
[ 2759.435740] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2759.435767] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2759.435771] sdc: sdc1
[ 2760.545669] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 2760.545717] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 2760.545995] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 2760.546083] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2760.546104] sd 1:2:0:0: [sdd] Write Protect is off
[ 2760.546108] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2760.546137] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2760.546191] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2760.546208] sd 1:2:0:0: [sdd] Write Protect is off
[ 2760.546211] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2760.546239] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2760.546243] sdd: sdd1
[ 2761.907801] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 2761.907850] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 2761.908125] scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 2761.908216] sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
[ 2761.908238] sd 1:5:0:0: [sde] Write Protect is off
[ 2761.908241] sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2761.908271] sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2761.908323] sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
[ 2761.908340] sd 1:5:0:0: [sde] Write Protect is off
[ 2761.908343] sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2761.908371] sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2761.908374] sde: unknown partition table
[ 2761.908705] sd 1:5:0:0: [sde] Attached SCSI disk
[ 2761.908740] sd 1:5:0:0: Attached scsi generic sg5 type 0
[ 2998.839318] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2998.839324] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2998.839327] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2998.839330] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2998.839333] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2998.839336] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2998.839339] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2998.839343] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2998.839347] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 2998.839351] ata1: SError: { 10B8B }
[ 2998.839356] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839361] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839366] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839371] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839376] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839382] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839387] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839394] ata1.15: hard resetting link
[ 3003.931768] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 3004.183686] ata1.15: qc timeout (cmd 0xe4)
[ 3004.183694] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 3004.183697] ata1.15: PMP revalidation failed (errno=-5)
[ 3004.183700] ata1.15: retrying hardreset in 5 secs
[ 3009.186168] ata1.15: hard resetting link
[ 3014.280627] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 3014.532545] ata1.15: qc timeout (cmd 0xe4)
[ 3014.532553] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 3014.532556] ata1.15: PMP revalidation failed (errno=-5)
[ 3014.532560] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 3014.532563] ata1.15: retrying hardreset in 5 secs
[ 3019.535029] ata1.15: hard resetting link
[ 3021.734370] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 3021.734603] ata1.00: hard resetting link
[ 3022.054452] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3022.054456] ata1.01: hard resetting link
[ 3022.374353] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3022.374357] ata1.02: hard resetting link
[ 3022.694255] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3022.694259] ata1.03: hard resetting link
[ 3023.014158] ata1.03: SATA link down (SStatus 0 SControl 310)
[ 3023.014161] ata1.04: hard resetting link
[ 3023.334063] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3023.334067] ata1.05: hard resetting link
[ 3023.653963] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 3023.653967] ata1.06: hard resetting link
[ 3023.973871] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3023.976070] ata1.00: configured for UDMA/100
[ 3023.978246] ata1.01: configured for UDMA/100
[ 3024.074973] ata1.02: configured for UDMA/100
[ 3024.075027] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 3024.075194] ata1.05: device is on DMA blacklist, disabling DMA
[ 3024.075300] ata1.05: configured for PIO4
[ 3024.075303] ata1: failed to recover some devices, retrying in 5 secs
[ 3029.076135] ata1.04: hard resetting link
[ 3029.396222] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3029.396279] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 3029.396282] ata1: failed to recover some devices, retrying in 5 secs
[ 3034.398519] ata1.04: hard resetting link
[ 3034.718607] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3034.718663] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 3034.718666] ata1: failed to recover some devices, retrying in 5 secs
[ 3039.720910] ata1.04: hard resetting link
[ 3040.040995] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3040.041276] ata1: EH complete
[ 3040.041304] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041316] sd 1:0:0:0: [sdb] Write Protect is off
[ 3040.041319] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3040.041332] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041348] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041356] sd 1:1:0:0: [sdc] Write Protect is off
[ 3040.041359] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3040.041370] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041383] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041391] sd 1:2:0:0: [sdd] Write Protect is off
[ 3040.041394] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 3040.041405] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041418] sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
[ 3040.041426] sd 1:5:0:0: [sde] Write Protect is off
[ 3040.041429] sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
[ 3040.041440] sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041453] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041460] sd 1:0:0:0: [sdb] Write Protect is off
[ 3040.041463] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3040.041474] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041487] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041494] sd 1:1:0:0: [sdc] Write Protect is off
[ 3040.041497] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3040.041508] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041520] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041528] sd 1:2:0:0: [sdd] Write Protect is off
[ 3040.041531] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 3040.041542] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041554] sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
[ 3040.041562] sd 1:5:0:0: [sde] Write Protect is off
[ 3040.041564] sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
[ 3040.041672] sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[-- Attachment #11: 10_PlugUnplug.log --]
[-- Type: text/plain, Size: 31277 bytes --]
esn't support DPO or FUA
[ 2352.862706] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2352.862714] sd 1:5:0:0: [sdf] Write Protect is off
[ 2352.862717] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2352.862728] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2467.824811] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2467.824817] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2467.824820] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2467.824823] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2467.824826] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2467.824829] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2467.824832] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2467.824837] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2467.824840] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 2467.824844] ata1: SError: { 10B8B }
[ 2467.824849] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824854] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824859] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824864] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824870] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824875] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824880] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2467.824887] ata1.15: hard resetting link
[ 2472.916873] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2473.168790] ata1.15: qc timeout (cmd 0xe4)
[ 2473.168799] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2473.168802] ata1.15: PMP revalidation failed (errno=-5)
[ 2473.168805] ata1.15: retrying hardreset in 5 secs
[ 2478.171271] ata1.15: hard resetting link
[ 2483.265729] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2483.517647] ata1.15: qc timeout (cmd 0xe4)
[ 2483.517655] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2483.517658] ata1.15: PMP revalidation failed (errno=-5)
[ 2483.517662] ata1.15: retrying hardreset in 5 secs
[ 2488.520130] ata1.15: hard resetting link
[ 2490.719472] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 2490.719682] ata1.00: hard resetting link
[ 2491.039551] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2491.039554] ata1.01: hard resetting link
[ 2491.359454] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2491.359458] ata1.02: hard resetting link
[ 2491.679359] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2491.679363] ata1.03: hard resetting link
[ 2491.999261] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2491.999265] ata1.04: hard resetting link
[ 2492.319165] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 2492.319168] ata1.05: hard resetting link
[ 2492.639066] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 2492.639070] ata1.06: hard resetting link
[ 2492.958971] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2492.961345] ata1.00: configured for UDMA/100
[ 2492.963537] ata1.01: configured for UDMA/100
[ 2492.963689] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2492.963693] ata1.02: revalidation failed (errno=-5)
[ 2492.963824] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2492.963828] ata1.03: revalidation failed (errno=-5)
[ 2492.963962] ata1.05: device is on DMA blacklist, disabling DMA
[ 2492.964068] ata1.05: configured for PIO4
[ 2492.964071] ata1: failed to recover some devices, retrying in 5 secs
[ 2497.965270] ata1.02: hard resetting link
[ 2498.285353] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2498.285358] ata1.03: hard resetting link
[ 2498.605256] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2498.710753] ata1.02: configured for UDMA/100
[ 2498.710857] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2498.710861] ata1.03: revalidation failed (errno=-5)
[ 2498.710865] ata1: failed to recover some devices, retrying in 5 secs
[ 2503.711527] ata1.03: hard resetting link
[ 2504.031610] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2504.031731] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2504.031735] ata1.03: revalidation failed (errno=-5)
[ 2504.031738] ata1.03: disabled
[ 2504.535271] ata1.03: hard resetting link
[ 2504.855360] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2504.855415] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2504.855419] ata1: failed to recover some devices, retrying in 5 secs
[ 2509.857662] ata1.03: hard resetting link
[ 2510.177746] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2510.177809] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2510.177814] ata1: failed to recover some devices, retrying in 5 secs
[ 2515.180048] ata1.03: hard resetting link
[ 2515.500132] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2515.500195] ata1.03: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2515.500199] ata1: failed to recover some devices, retrying in 5 secs
[ 2520.502428] ata1.03: hard resetting link
[ 2520.822515] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2520.822793] ata1: EH complete
[ 2520.822822] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822834] sd 1:0:0:0: [sdb] Write Protect is off
[ 2520.822837] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2520.822850] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822866] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822874] sd 1:1:0:0: [sdc] Write Protect is off
[ 2520.822877] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2520.822888] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822901] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822910] sd 1:2:0:0: [sdd] Write Protect is off
[ 2520.822912] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2520.822924] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822937] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2520.822944] sd 1:5:0:0: [sdf] Write Protect is off
[ 2520.822947] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2520.822959] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.822971] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.822979] sd 1:0:0:0: [sdb] Write Protect is off
[ 2520.822982] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2520.822993] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823005] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.823012] sd 1:1:0:0: [sdc] Write Protect is off
[ 2520.823015] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2520.823026] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823039] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2520.823046] sd 1:2:0:0: [sdd] Write Protect is off
[ 2520.823049] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2520.823060] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823073] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 2520.823080] sd 1:5:0:0: [sdf] Write Protect is off
[ 2520.823083] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2520.823094] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2520.823100] ata1.03: detaching (SCSI 1:3:0:0)
[ 2520.823274] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 2520.823738] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 2520.823742] sd 1:3:0:0: [sde] Stopping disk
[ 2520.824243] sd 1:3:0:0: [sde] START_STOP FAILED
[ 2520.824246] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 2689.226123] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2689.226129] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2689.226132] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2689.226135] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2689.226138] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2689.226141] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2689.226144] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2689.226148] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2689.226152] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 2689.226156] ata1: SError: { 10B8B }
[ 2689.226161] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226166] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226171] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226176] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226181] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226186] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226192] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2689.226199] ata1.15: hard resetting link
[ 2694.317699] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2694.569617] ata1.15: qc timeout (cmd 0xe4)
[ 2694.569625] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2694.569628] ata1.15: PMP revalidation failed (errno=-5)
[ 2694.569631] ata1.15: retrying hardreset in 5 secs
[ 2699.572098] ata1.15: hard resetting link
[ 2704.666558] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2704.918477] ata1.15: qc timeout (cmd 0xe4)
[ 2704.918484] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2704.918487] ata1.15: PMP revalidation failed (errno=-5)
[ 2704.918491] ata1.15: retrying hardreset in 5 secs
[ 2709.920959] ata1.15: hard resetting link
[ 2715.015418] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2715.267337] ata1.15: qc timeout (cmd 0xe4)
[ 2715.267344] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2715.267347] ata1.15: PMP revalidation failed (errno=-5)
[ 2715.267351] ata1.15: retrying hardreset in 5 secs
[ 2720.269819] ata1.15: hard resetting link
[ 2725.364279] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2725.616196] ata1.15: qc timeout (cmd 0xe4)
[ 2725.616204] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2725.616207] ata1.15: PMP revalidation failed (errno=-5)
[ 2725.616210] ata1.15: retrying hardreset in 5 secs
[ 2730.618679] ata1.15: hard resetting link
[ 2735.713139] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 2735.965057] ata1.15: qc timeout (cmd 0xe4)
[ 2735.965064] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 2735.965067] ata1.15: PMP revalidation failed (errno=-5)
[ 2735.965070] ata1.15: failed to recover PMP after 5 tries, giving up
[ 2735.965073] ata1.15: Port Multiplier detaching
[ 2735.965081] ata1.00: disabled
[ 2735.965084] ata1.01: disabled
[ 2735.965087] ata1.02: disabled
[ 2735.965089] ata1.05: disabled
[ 2735.965092] ata1.00: disabled
[ 2735.965098] ata1: hard resetting link
[ 2739.308053] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 2739.308243] ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
[ 2739.308453] ata1.00: hard resetting link
[ 2739.628109] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2739.628113] ata1.01: hard resetting link
[ 2739.948009] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2739.948013] ata1.02: hard resetting link
[ 2740.267914] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2740.267918] ata1.03: hard resetting link
[ 2740.587815] ata1.03: SATA link down (SStatus 0 SControl 320)
[ 2740.587819] ata1.04: hard resetting link
[ 2740.907722] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2740.907726] ata1.05: hard resetting link
[ 2741.227621] ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 2741.227624] ata1.06: hard resetting link
[ 2741.547525] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2741.547584] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2741.567765] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2741.587927] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2741.608087] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2741.628249] ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
[ 2741.628252] ata1.05: 640 sectors, multi 1: LBA
[ 2741.628261] ata1.05: device is on DMA blacklist, disabling DMA
[ 2741.628464] ata1.05: configured for PIO4
[ 2741.628468] ata1: failed to recover some devices, retrying in 5 secs
[ 2746.629822] ata1.00: hard resetting link
[ 2746.949886] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2746.949891] ata1.01: hard resetting link
[ 2747.269789] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2747.269793] ata1.02: hard resetting link
[ 2747.589691] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2747.589695] ata1.04: hard resetting link
[ 2747.909595] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2747.910678] ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 2747.910681] ata1.00: 586072368 sectors, multi 0: LBA48
[ 2747.910684] ata1.00: applying bridge limits
[ 2747.911859] ata1.00: configured for UDMA/100
[ 2747.912923] ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 2747.912926] ata1.01: 586072368 sectors, multi 0: LBA48
[ 2747.912929] ata1.01: applying bridge limits
[ 2747.914104] ata1.01: configured for UDMA/100
[ 2747.960737] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 2747.960740] ata1.02: 586072368 sectors, multi 0: LBA48
[ 2747.960743] ata1.02: applying bridge limits
[ 2748.018887] ata1.02: configured for UDMA/100
[ 2748.018981] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2748.019122] ata1.05: device is on DMA blacklist, disabling DMA
[ 2748.019288] ata1.05: configured for PIO4
[ 2748.019291] ata1: failed to recover some devices, retrying in 5 secs
[ 2753.019883] ata1.04: hard resetting link
[ 2753.339948] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2753.342229] ata1.00: configured for UDMA/100
[ 2753.344443] ata1.01: configured for UDMA/100
[ 2753.434140] ata1.02: configured for UDMA/100
[ 2753.434235] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 2753.434239] ata1: failed to recover some devices, retrying in 5 secs
[ 2758.434240] ata1.04: hard resetting link
[ 2758.754305] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 2758.754564] ata1: EH complete
[ 2758.754572] ata1.00: detaching (SCSI 1:0:0:0)
[ 2758.754749] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 2758.755045] sd 1:0:0:0: [sdb] Stopping disk
[ 2758.755191] ata1.01: detaching (SCSI 1:1:0:0)
[ 2758.755325] sd 1:1:0:0: [sdc] Synchronizing SCSI cache
[ 2758.755839] sd 1:1:0:0: [sdc] Stopping disk
[ 2758.756172] ata1.02: detaching (SCSI 1:2:0:0)
[ 2758.756322] sd 1:2:0:0: [sdd] Synchronizing SCSI cache
[ 2758.756426] sd 1:2:0:0: [sdd] Stopping disk
[ 2758.756533] ata1.05: detaching (SCSI 1:5:0:0)
[ 2758.756655] sd 1:5:0:0: [sdf] Stopping disk
[ 2758.756846] scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 2758.756973] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2758.757000] sd 1:0:0:0: [sdb] Write Protect is off
[ 2758.757003] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2758.757032] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2758.757212] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 2758.757237] sd 1:0:0:0: [sdb] Write Protect is off
[ 2758.757240] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2758.757267] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2758.757273] sdb: sdb1
[ 2759.435145] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 2759.435193] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 2759.435522] scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 2759.435611] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2759.435632] sd 1:1:0:0: [sdc] Write Protect is off
[ 2759.435636] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2759.435665] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2759.435719] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 2759.435737] sd 1:1:0:0: [sdc] Write Protect is off
[ 2759.435740] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2759.435767] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2759.435771] sdc: sdc1
[ 2760.545669] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 2760.545717] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 2760.545995] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 2760.546083] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2760.546104] sd 1:2:0:0: [sdd] Write Protect is off
[ 2760.546108] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2760.546137] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2760.546191] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 2760.546208] sd 1:2:0:0: [sdd] Write Protect is off
[ 2760.546211] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2760.546239] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2760.546243] sdd: sdd1
[ 2761.907801] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 2761.907850] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 2761.908125] scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 2761.908216] sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
[ 2761.908238] sd 1:5:0:0: [sde] Write Protect is off
[ 2761.908241] sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2761.908271] sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2761.908323] sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
[ 2761.908340] sd 1:5:0:0: [sde] Write Protect is off
[ 2761.908343] sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2761.908371] sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2761.908374] sde: unknown partition table
[ 2761.908705] sd 1:5:0:0: [sde] Attached SCSI disk
[ 2761.908740] sd 1:5:0:0: Attached scsi generic sg5 type 0
[ 2998.839318] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 2998.839324] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 2998.839327] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 2998.839330] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 2998.839333] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 2998.839336] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 2998.839339] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 2998.839343] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 2998.839347] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 2998.839351] ata1: SError: { 10B8B }
[ 2998.839356] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839361] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839366] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839371] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839376] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839382] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839387] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2998.839394] ata1.15: hard resetting link
[ 3003.931768] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 3004.183686] ata1.15: qc timeout (cmd 0xe4)
[ 3004.183694] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 3004.183697] ata1.15: PMP revalidation failed (errno=-5)
[ 3004.183700] ata1.15: retrying hardreset in 5 secs
[ 3009.186168] ata1.15: hard resetting link
[ 3014.280627] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 3014.532545] ata1.15: qc timeout (cmd 0xe4)
[ 3014.532553] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 3014.532556] ata1.15: PMP revalidation failed (errno=-5)
[ 3014.532560] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 3014.532563] ata1.15: retrying hardreset in 5 secs
[ 3019.535029] ata1.15: hard resetting link
[ 3021.734370] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 3021.734603] ata1.00: hard resetting link
[ 3022.054452] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3022.054456] ata1.01: hard resetting link
[ 3022.374353] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3022.374357] ata1.02: hard resetting link
[ 3022.694255] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3022.694259] ata1.03: hard resetting link
[ 3023.014158] ata1.03: SATA link down (SStatus 0 SControl 310)
[ 3023.014161] ata1.04: hard resetting link
[ 3023.334063] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3023.334067] ata1.05: hard resetting link
[ 3023.653963] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 3023.653967] ata1.06: hard resetting link
[ 3023.973871] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3023.976070] ata1.00: configured for UDMA/100
[ 3023.978246] ata1.01: configured for UDMA/100
[ 3024.074973] ata1.02: configured for UDMA/100
[ 3024.075027] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 3024.075194] ata1.05: device is on DMA blacklist, disabling DMA
[ 3024.075300] ata1.05: configured for PIO4
[ 3024.075303] ata1: failed to recover some devices, retrying in 5 secs
[ 3029.076135] ata1.04: hard resetting link
[ 3029.396222] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3029.396279] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 3029.396282] ata1: failed to recover some devices, retrying in 5 secs
[ 3034.398519] ata1.04: hard resetting link
[ 3034.718607] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3034.718663] ata1.04: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 3034.718666] ata1: failed to recover some devices, retrying in 5 secs
[ 3039.720910] ata1.04: hard resetting link
[ 3040.040995] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3040.041276] ata1: EH complete
[ 3040.041304] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041316] sd 1:0:0:0: [sdb] Write Protect is off
[ 3040.041319] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3040.041332] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041348] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041356] sd 1:1:0:0: [sdc] Write Protect is off
[ 3040.041359] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3040.041370] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041383] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041391] sd 1:2:0:0: [sdd] Write Protect is off
[ 3040.041394] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 3040.041405] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041418] sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
[ 3040.041426] sd 1:5:0:0: [sde] Write Protect is off
[ 3040.041429] sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
[ 3040.041440] sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041453] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041460] sd 1:0:0:0: [sdb] Write Protect is off
[ 3040.041463] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3040.041474] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041487] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041494] sd 1:1:0:0: [sdc] Write Protect is off
[ 3040.041497] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3040.041508] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041520] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 3040.041528] sd 1:2:0:0: [sdd] Write Protect is off
[ 3040.041531] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 3040.041542] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3040.041554] sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
[ 3040.041562] sd 1:5:0:0: [sde] Write Protect is off
[ 3040.041564] sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
[ 3040.041672] sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3302.216486] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 3302.216492] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 3302.216495] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 3302.216498] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 3302.216501] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 3302.216504] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 3302.216507] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 3302.216512] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 3302.216515] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 3302.216519] ata1: SError: { 10B8B }
[ 3302.216524] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 3302.216529] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 3302.216534] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 3302.216539] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 3302.216544] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 3302.216549] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 3302.216555] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 3302.216562] ata1.15: hard resetting link
[ 3304.292643] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 3304.544560] ata1.15: qc timeout (cmd 0xe4)
[ 3304.544568] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 3304.544571] ata1.15: PMP revalidation failed (errno=-5)
[ 3304.544575] ata1.15: retrying hardreset in 5 secs
[ 3309.547042] ata1.15: hard resetting link
[ 3311.626416] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 3311.878334] ata1.15: qc timeout (cmd 0xe4)
[ 3311.878342] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 3311.878345] ata1.15: PMP revalidation failed (errno=-5)
[ 3311.878348] ata1.15: retrying hardreset in 5 secs
[ 3316.880818] ata1.15: hard resetting link
[ 3318.960192] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 3319.212110] ata1.15: qc timeout (cmd 0xe4)
[ 3319.212117] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 3319.212120] ata1.15: PMP revalidation failed (errno=-5)
[ 3319.212124] ata1.15: retrying hardreset in 5 secs
[ 3324.214593] ata1.15: hard resetting link
[ 3326.413935] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 3326.414147] ata1.00: hard resetting link
[ 3326.734016] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3326.734024] ata1.01: hard resetting link
[ 3327.053917] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3327.053922] ata1.02: hard resetting link
[ 3327.373820] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3327.373824] ata1.03: hard resetting link
[ 3327.693723] ata1.03: SATA link down (SStatus 0 SControl 310)
[ 3327.693727] ata1.04: hard resetting link
[ 3328.013626] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3328.013630] ata1.05: hard resetting link
[ 3328.333526] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 3328.333530] ata1.06: hard resetting link
[ 3328.653435] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3328.655654] ata1.00: configured for UDMA/100
[ 3328.657868] ata1.01: configured for UDMA/100
[ 3328.765843] ata1.02: configured for UDMA/100
[ 3328.813649] ata1.04: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 3328.813653] ata1.04: 586072368 sectors, multi 0: LBA48
[ 3328.813656] ata1.04: applying bridge limits
[ 3328.871922] ata1.04: configured for UDMA/100
[ 3328.872028] ata1.05: device is on DMA blacklist, disabling DMA
[ 3328.872132] ata1.05: configured for PIO4
[ 3328.872404] ata1: EH complete
[ 3328.872428] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 3328.872440] sd 1:0:0:0: [sdb] Write Protect is off
[ 3328.872443] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3328.872456] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3328.872471] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 3328.872478] sd 1:1:0:0: [sdc] Write Protect is off
[ 3328.872481] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3328.872493] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3328.872506] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 3328.872514] sd 1:2:0:0: [sdd] Write Protect is off
[ 3328.872517] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 3328.872528] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3328.872541] sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
[ 3328.872549] sd 1:5:0:0: [sde] Write Protect is off
[ 3328.872552] sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
[ 3328.872563] sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3328.872576] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 3328.872584] sd 1:0:0:0: [sdb] Write Protect is off
[ 3328.872587] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3328.872598] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3328.872610] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 3328.872618] sd 1:1:0:0: [sdc] Write Protect is off
[ 3328.872621] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3328.872632] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3328.872644] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 3328.872652] sd 1:2:0:0: [sdd] Write Protect is off
[ 3328.872655] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 3328.872666] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3328.872679] sd 1:5:0:0: [sde] 640 512-byte hardware sectors (0 MB)
[ 3328.872686] sd 1:5:0:0: [sde] Write Protect is off
[ 3328.872689] sd 1:5:0:0: [sde] Mode Sense: 00 3a 00 00
[ 3328.872700] sd 1:5:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3328.872773] scsi 1:4:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 3328.873213] sd 1:4:0:0: [sdf] 586072368 512-byte hardware sectors (300069 MB)
[ 3328.873222] sd 1:4:0:0: [sdf] Write Protect is off
[ 3328.873225] sd 1:4:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 3328.873237] sd 1:4:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3328.873681] sd 1:4:0:0: [sdf] 586072368 512-byte hardware sectors (300069 MB)
[ 3328.873690] sd 1:4:0:0: [sdf] Write Protect is off
[ 3328.873693] sd 1:4:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 3328.873705] sd 1:4:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3328.873709] sdf: sdf1
[ 3328.911665] sd 1:4:0:0: [sdf] Attached SCSI disk
[ 3328.911714] sd 1:4:0:0: Attached scsi generic sg6 type 0
[-- Attachment #12: TestingRoutine.txt --]
[-- Type: text/plain, Size: 3581 bytes --]
Sata 4726 testing: 4726 on at boot:
1. Cold boot computer, powere the sata 4726 before booting.
Notes: Turned on 4726, unit powered up. Only first drive is auto-detected during the 3124 HBA's BIOS.
Booting linux, all drives detected on PMP. All drive status light on storage tower are on.
File: 1_Bootup.log
2. Turn 4726 off, wait 10 seconds, turn 4726 on
Notes: All drives detected properly when unit was turned back on. Verified existance using fdisk.
3. Repeat #2.
Notes: ata1.03 was not recognized this time. All drive status lights on storage tower are on,
including for ata1.03, indicating some sort of detection?
File: 2_PowerOnOffTwice.log
4. Unplug 4726, wait 10 seconds, plug back in (leave 4726 powered up)
Notes: All 4 drives detected properly. Verified with fdisk.
File: 3_PlugUnplug.txt
5. Power 4726 off, wait 10 seconds, power back on 4726
Notes: ata1.03 was not dected, All drive status lights on storage tower are on,
including for ata1.03, indicating some sort of detection?
6. Repeat step #5
Notes: ata1.03 not detected again. All drive status lights on storage tower are on,
including for ata1.03, indicating some sort of detection?
I did double check all of the drives in the storage tower, all of the
IDE to SATA adapters and cables are plugged in.
File: 4_PowerOnOffTwice.log
7. Turned 4726 off. Swap drives on 3rd and 4th port of 4726 around to see if this
changes anything. Power 4726 back on.
Notes: Drives on first 3 ports are recognized, but ata1.03 are recognized. All
drive status lights are lit.
File: 5_DriveSwap.log
8. Repeating tests 2 through 6.
8.1 Repeating #2
Notes: First 3 drives come up, ata1.03 is not detected. All
drive status lights are lit.
8.2 Repeating #3
Notes: First 3 drives come up, ata1.03 is not detected. All
drive status lights are lit.
File: 6_PowerOnOff.log
8.3 Repeating #4
Notes: All 4 drives are detected properly.
File: 7_PlugUnplug.log
8.4 Repeating #5
Notes: All drives were detected. Verified using fdisk.
8.6 Repeating #6
Notes: ata1.03 failed to be detected, first 3 drives were detected ok.
File: 8_PowerOnOffTwice.log
9. Powering off 4726, Reversing drive swap test as noted in Step #7.
Moving drive on 4th SATA port of 4726 to 5th SATA port.
Notes: ata1.04 or is it ata1.05(??) is not recognized. First 3 drives are detected properly.
I did have a spare LED to install on the 5th status LED port,
so I can't tell what the status is.
10. Powering 4726 off, waiting 10 seconds, then on.
Notes: Same results as in #9. ata1.04 is not recognized.
Looking at the logs,
File: 9_OccupyLastPMPPort.log
11. Unplugging 4726 from HBA, waiting 10 seconds, and re-plugging.
Notes: All 4 drives detected properly. ata1.04 is recognized.
File: 10_PlugUnplug.log
/dev/sde for ata1.03 is created, but invalid:
BigMouth timestamped # fdisk /dev/sde
Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel
Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that, of course, the previous
content won't be recoverable.
You must set cylinders.
You can do this from the extra functions menu.
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)
Command (m for help): p
Disk /dev/sde: 0 MB, 327680 bytes
255 heads, 63 sectors/track, 0 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
Command (m for help): q
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-11 1:19 ` Andrew Ryder
@ 2008-01-11 7:49 ` Tejun Heo
2008-01-11 23:13 ` Andrew Ryder
0 siblings, 1 reply; 26+ messages in thread
From: Tejun Heo @ 2008-01-11 7:49 UTC (permalink / raw)
To: Andrew Ryder; +Cc: Gaston, Jason D, linux-ide
[-- Attachment #1: Type: text/plain, Size: 921 bytes --]
Andrew Ryder wrote:
> For the regular power on detected, are you referring to cold/warm
> booting the system and verifying initialization or only power cycling
> the 4726?
>
> Here are my test results, TestingRoutine.txt is the procedure I followed
> and test results obtained. If I missed something, please let me know.
>
> From what I could find, the problem with ata1.03 not being detected is
> consistent with the port. In my testing, I moved the last drive to the
> 5th port on the 4726 and the problem carried through. The issue seemed
> to only occur when the 4726 was powered on/off, not when it was
> unplugged and re-plugged with the power on.
>
> If I have some time on the weekend, I will do a test routine of several
> hot un-plugs / re-plugs of the 4726 and see what happens.
Thanks a lot for all the testing. Can you please apply the attached
patch and see whether things improve?
Thanks.
--
tejun
[-- Attachment #2: sil24-freeze-fix.patch --]
[-- Type: text/x-patch, Size: 1058 bytes --]
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index b4c674d..864c1c1 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -301,7 +301,7 @@ static struct sil24_cerr_info {
[PORT_CERR_PKT_PROT] = { AC_ERR_HSM, ATA_EH_SOFTRESET,
"invalid data directon for ATAPI CDB" },
[PORT_CERR_SGT_BOUNDARY] = { AC_ERR_SYSTEM, ATA_EH_SOFTRESET,
- "SGT no on qword boundary" },
+ "SGT not on qword boundary" },
[PORT_CERR_SGT_TGTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET,
"PCI target abort while fetching SGT" },
[PORT_CERR_SGT_MSTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET,
@@ -1094,10 +1094,13 @@ static void sil24_error_intr(struct ata_port *ap)
if (ci && ci->desc) {
err_mask |= ci->err_mask;
action |= ci->action;
+ if (action & ATA_EH_RESET_MASK)
+ freeze = 1;
ata_ehi_push_desc(ehi, "%s", ci->desc);
} else {
err_mask |= AC_ERR_OTHER;
action |= ATA_EH_SOFTRESET;
+ freeze = 1;
ata_ehi_push_desc(ehi, "unknown command error %d",
cerr);
}
^ permalink raw reply related [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-11 7:49 ` Tejun Heo
@ 2008-01-11 23:13 ` Andrew Ryder
2008-01-13 5:10 ` Tejun Heo
0 siblings, 1 reply; 26+ messages in thread
From: Andrew Ryder @ 2008-01-11 23:13 UTC (permalink / raw)
To: Tejun Heo; +Cc: Gaston, Jason D, linux-ide
[-- Attachment #1: Type: text/plain, Size: 1325 bytes --]
Tejun,
No problem. I should be thanking you and your team for all the hard work
writing the drivers for the hardware..
I think this patch might have solved the issue. I did a quick test: warm
rebooted and turned the 4726 on and off 3 times and all disks were
successfully detected each time. I'll do a more thorough test tomorrow
or Sunday.
Thanks
Tejun Heo wrote:
> Andrew Ryder wrote:
>
>> For the regular power on detected, are you referring to cold/warm
>> booting the system and verifying initialization or only power cycling
>> the 4726?
>>
>> Here are my test results, TestingRoutine.txt is the procedure I followed
>> and test results obtained. If I missed something, please let me know.
>>
>> >From what I could find, the problem with ata1.03 not being detected is
>> consistent with the port. In my testing, I moved the last drive to the
>> 5th port on the 4726 and the problem carried through. The issue seemed
>> to only occur when the 4726 was powered on/off, not when it was
>> unplugged and re-plugged with the power on.
>>
>> If I have some time on the weekend, I will do a test routine of several
>> hot un-plugs / re-plugs of the 4726 and see what happens.
>>
>
> Thanks a lot for all the testing. Can you please apply the attached
> patch and see whether things improve?
>
> Thanks.
>
>
[-- Attachment #2: quicktest.txt --]
[-- Type: text/plain, Size: 31313 bytes --]
3.0 Gbps (SStatus 123 SControl 0)
[ 64.068586] ata1.06: hard resetting link
[ 64.388488] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 64.389577] ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 64.389580] ata1.00: 586072368 sectors, multi 16: LBA48
[ 64.389583] ata1.00: applying bridge limits
[ 64.390715] ata1.00: configured for UDMA/100
[ 64.391771] ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 64.391773] ata1.01: 586072368 sectors, multi 0: LBA48
[ 64.391775] ata1.01: applying bridge limits
[ 64.392913] ata1.01: configured for UDMA/100
[ 64.438134] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 64.438137] ata1.02: 586072368 sectors, multi 0: LBA48
[ 64.438139] ata1.02: applying bridge limits
[ 64.496278] ata1.02: configured for UDMA/100
[ 64.539472] ata1.04: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 64.539475] ata1.04: 586072368 sectors, multi 0: LBA48
[ 64.539477] ata1.04: applying bridge limits
[ 64.597758] ata1.04: configured for UDMA/100
[ 64.597829] ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
[ 64.597832] ata1.05: 640 sectors, multi 1: LBA
[ 64.597839] ata1.05: device is on DMA blacklist, disabling DMA
[ 64.597929] ata1.05: configured for PIO4
[ 64.597969] ata1: EH complete
[ 66.675642] ata2: SATA link down (SStatus 0 SControl 0)
[ 68.755011] ata3: SATA link down (SStatus 0 SControl 0)
[ 70.834380] ata4: SATA link down (SStatus 0 SControl 0)
[ 70.834495] scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.834908] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.834919] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.834922] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.834934] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.834978] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.834985] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.834987] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.834998] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.835002] sdb: sdb1
[ 70.843975] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 70.844011] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 70.844453] scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.844729] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.844736] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.844739] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.844750] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.844779] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.844786] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.844788] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.844799] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.844802] sdc: sdc1
[ 70.863628] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 70.863659] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 70.864129] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.864190] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.864197] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.864200] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.864211] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.864240] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.864247] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.864249] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.864260] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.864263] sdd: sdd1
[ 70.881739] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 70.881772] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 70.881818] scsi 1:4:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.881877] sd 1:4:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.881884] sd 1:4:0:0: [sde] Write Protect is off
[ 70.881886] sd 1:4:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.881897] sd 1:4:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.882646] sd 1:4:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.882654] sd 1:4:0:0: [sde] Write Protect is off
[ 70.882656] sd 1:4:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.882667] sd 1:4:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.882670] sde: sde1
[ 70.898341] sd 1:4:0:0: [sde] Attached SCSI disk
[ 70.898375] sd 1:4:0:0: Attached scsi generic sg5 type 0
[ 70.898421] scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 70.898480] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.898487] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.898490] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.898501] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.898530] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.898537] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.898539] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.898550] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.898553] sdf: unknown partition table
[ 70.899398] sd 1:5:0:0: [sdf] Attached SCSI disk
[ 70.899430] sd 1:5:0:0: Attached scsi generic sg6 type 0
[ 70.899727] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.899738] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 70.899929] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 70.899958] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
[ 70.900097] usb usb1: configuration #1 chosen from 1 choice
[ 70.900124] hub 1-0:1.0: USB hub found
[ 70.900133] hub 1-0:1.0: 2 ports detected
[ 71.002471] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 71.002485] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 71.002509] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 71.002532] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 71.002652] usb usb2: configuration #1 chosen from 1 choice
[ 71.002678] hub 2-0:1.0: USB hub found
[ 71.002685] hub 2-0:1.0: 2 ports detected
[ 71.106425] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.106439] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 71.106464] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 71.106487] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 71.106608] usb usb3: configuration #1 chosen from 1 choice
[ 71.106632] hub 3-0:1.0: USB hub found
[ 71.106640] hub 3-0:1.0: 2 ports detected
[ 71.210424] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.210438] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 71.210463] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 71.210487] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 71.210606] usb usb4: configuration #1 chosen from 1 choice
[ 71.210631] hub 4-0:1.0: USB hub found
[ 71.210639] hub 4-0:1.0: 2 ports detected
[ 71.314524] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 71.316772] Audigy2 value: Special config.
[ 71.329677] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 71.330044] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 71.330104] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 71.330152] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
[ 71.338231] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 71.338350] usb usb5: configuration #1 chosen from 1 choice
[ 71.338377] hub 5-0:1.0: USB hub found
[ 71.338387] hub 5-0:1.0: 8 ports detected
[ 73.047330] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 73.047334] Copyright (c) 1999-2006 Intel Corporation.
[ 73.047376] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 73.047381] PCI: Disallowing DAC for device 0000:00:0e.0
[ 73.307233] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 73.482707] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 73.641789] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 73.641802] ReiserFS: hdb1: using ordered data mode
[ 73.677157] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 73.678508] ReiserFS: hdb1: checking transaction log (hdb1)
[ 73.795920] ReiserFS: hdb1: Using r5 hash to sort names
[ 73.842916] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 73.842927] ReiserFS: hda2: using ordered data mode
[ 73.847744] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 73.849101] ReiserFS: hda2: checking transaction log (hda2)
[ 73.903713] ReiserFS: hda2: Using r5 hash to sort names
[ 79.570937] hda: UDMA/100 mode selected
[ 79.574851] hdb: UDMA/133 mode selected
[ 79.629194] hdc: UDMA/33 mode selected
[ 79.647002] hdd: UDMA/33 mode selected
[ 82.211327] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 86.444756] w83627hf: Found W83697HF chip at 0x290
[ 137.853328] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 137.853333] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 137.853336] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 137.853338] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 137.853341] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 137.853343] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 137.853345] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 137.853349] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 137.853352] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 137.853356] ata1: SError: { 10B8B }
[ 137.853360] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 137.853364] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 137.853369] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 137.853373] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 137.853378] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 137.853382] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 137.853386] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 137.853393] ata1.15: hard resetting link
[ 142.944498] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 143.196416] ata1.15: qc timeout (cmd 0xe4)
[ 143.196423] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 143.196426] ata1.15: PMP revalidation failed (errno=-5)
[ 143.196428] ata1.15: retrying hardreset in 5 secs
[ 148.198897] ata1.15: hard resetting link
[ 153.293357] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 153.545275] ata1.15: qc timeout (cmd 0xe4)
[ 153.545282] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 153.545284] ata1.15: PMP revalidation failed (errno=-5)
[ 153.545288] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 153.545290] ata1.15: retrying hardreset in 5 secs
[ 158.547757] ata1.15: hard resetting link
[ 160.747099] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 160.747310] ata1.00: hard resetting link
[ 161.067177] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 161.067180] ata1.01: hard resetting link
[ 161.387081] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 161.387085] ata1.02: hard resetting link
[ 161.706985] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 161.706989] ata1.03: hard resetting link
[ 162.026886] ata1.03: SATA link down (SStatus 0 SControl 310)
[ 162.026889] ata1.04: hard resetting link
[ 162.346790] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 162.346794] ata1.05: hard resetting link
[ 162.666691] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 162.666694] ata1.06: hard resetting link
[ 162.986595] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 162.986705] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 162.986709] ata1.00: revalidation failed (errno=-5)
[ 162.986713] ata1.15: hard resetting link
[ 165.185753] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 165.185956] ata1.00: hard resetting link
[ 165.505832] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 165.505836] ata1.01: hard resetting link
[ 165.825734] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 165.825738] ata1.02: hard resetting link
[ 166.145638] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 166.145642] ata1.03: hard resetting link
[ 166.465539] ata1.03: SATA link down (SStatus 0 SControl 310)
[ 166.465542] ata1.04: hard resetting link
[ 166.785447] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 166.785455] ata1.05: hard resetting link
[ 167.105345] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 167.105348] ata1.06: hard resetting link
[ 167.425248] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 167.427459] ata1.00: configured for UDMA/100
[ 167.429696] ata1.01: configured for UDMA/100
[ 167.542073] ata1.02: configured for UDMA/100
[ 167.650192] ata1.04: configured for UDMA/100
[ 167.650302] ata1.05: device is on DMA blacklist, disabling DMA
[ 167.650455] ata1.05: configured for PIO4
[ 167.650733] ata1: EH complete
[ 167.650759] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 167.650770] sd 1:0:0:0: [sdb] Write Protect is off
[ 167.650773] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 167.650786] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 167.650801] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 167.650808] sd 1:1:0:0: [sdc] Write Protect is off
[ 167.650811] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 167.650823] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 167.650836] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 167.650844] sd 1:2:0:0: [sdd] Write Protect is off
[ 167.650847] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 167.650858] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 167.650871] sd 1:4:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 167.650879] sd 1:4:0:0: [sde] Write Protect is off
[ 167.650882] sd 1:4:0:0: [sde] Mode Sense: 00 3a 00 00
[ 167.650893] sd 1:4:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 167.650906] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 167.650914] sd 1:5:0:0: [sdf] Write Protect is off
[ 167.650917] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 167.650928] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 167.650941] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 167.650948] sd 1:0:0:0: [sdb] Write Protect is off
[ 167.650951] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 167.650962] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 167.650975] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 167.650982] sd 1:1:0:0: [sdc] Write Protect is off
[ 167.650985] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 167.650996] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 167.651009] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 167.651016] sd 1:2:0:0: [sdd] Write Protect is off
[ 167.651019] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 167.651030] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 167.651043] sd 1:4:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 167.651050] sd 1:4:0:0: [sde] Write Protect is off
[ 167.651053] sd 1:4:0:0: [sde] Mode Sense: 00 3a 00 00
[ 167.651064] sd 1:4:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 167.651077] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 167.651084] sd 1:5:0:0: [sdf] Write Protect is off
[ 167.651087] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 167.651098] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 255.113670] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 255.113675] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 255.113679] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 255.113682] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 255.113685] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 255.113688] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 255.113691] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 255.113695] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 255.113698] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 255.113702] ata1: SError: { 10B8B }
[ 255.113707] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 255.113712] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 255.113718] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 255.113723] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 255.113728] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 255.113733] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 255.113738] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 255.113746] ata1.15: hard resetting link
[ 260.204923] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 260.456841] ata1.15: qc timeout (cmd 0xe4)
[ 260.456849] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 260.456852] ata1.15: PMP revalidation failed (errno=-5)
[ 260.456855] ata1.15: retrying hardreset in 5 secs
[ 265.459323] ata1.15: hard resetting link
[ 270.553782] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 270.805701] ata1.15: qc timeout (cmd 0xe4)
[ 270.805709] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 270.805712] ata1.15: PMP revalidation failed (errno=-5)
[ 270.805715] ata1.15: retrying hardreset in 5 secs
[ 275.808184] ata1.15: hard resetting link
[ 278.007526] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 278.007739] ata1.00: hard resetting link
[ 278.327605] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 278.327609] ata1.01: hard resetting link
[ 278.647507] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 278.647511] ata1.02: hard resetting link
[ 278.967409] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 278.967412] ata1.03: hard resetting link
[ 279.287313] ata1.03: SATA link down (SStatus 0 SControl 310)
[ 279.287317] ata1.04: hard resetting link
[ 279.607217] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 279.607221] ata1.05: hard resetting link
[ 279.927117] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 279.927120] ata1.06: hard resetting link
[ 280.247021] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 280.247140] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 280.247144] ata1.00: revalidation failed (errno=-5)
[ 280.247149] ata1.15: hard resetting link
[ 282.446181] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 282.446476] ata1.00: hard resetting link
[ 282.766257] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 282.766261] ata1.01: hard resetting link
[ 283.086161] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 283.086165] ata1.02: hard resetting link
[ 283.406065] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 283.406069] ata1.03: hard resetting link
[ 283.725965] ata1.03: SATA link down (SStatus 0 SControl 310)
[ 283.725968] ata1.04: hard resetting link
[ 284.045870] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 284.045874] ata1.05: hard resetting link
[ 284.365770] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 284.365774] ata1.06: hard resetting link
[ 284.685674] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 284.687930] ata1.00: configured for UDMA/100
[ 284.690132] ata1.01: configured for UDMA/100
[ 284.690241] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 284.690245] ata1.02: revalidation failed (errno=-5)
[ 284.690250] ata1.15: hard resetting link
[ 286.888832] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 286.889036] ata1.00: hard resetting link
[ 287.208910] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 287.208915] ata1.01: hard resetting link
[ 287.528814] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 287.528818] ata1.02: hard resetting link
[ 287.848716] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 287.848720] ata1.03: hard resetting link
[ 288.168618] ata1.03: SATA link down (SStatus 0 SControl 310)
[ 288.168622] ata1.04: hard resetting link
[ 288.488523] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 288.488527] ata1.05: hard resetting link
[ 288.808424] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 288.808427] ata1.06: hard resetting link
[ 289.128328] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 289.130548] ata1.00: configured for UDMA/100
[ 289.132742] ata1.01: configured for UDMA/100
[ 289.227715] ata1.02: configured for UDMA/100
[ 289.329614] ata1.04: configured for UDMA/100
[ 289.329723] ata1.05: device is on DMA blacklist, disabling DMA
[ 289.329833] ata1.05: configured for PIO4
[ 289.330106] ata1: EH complete
[ 289.330132] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 289.330144] sd 1:0:0:0: [sdb] Write Protect is off
[ 289.330147] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 289.330160] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 289.330175] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 289.330183] sd 1:1:0:0: [sdc] Write Protect is off
[ 289.330186] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 289.330197] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 289.330211] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 289.330219] sd 1:2:0:0: [sdd] Write Protect is off
[ 289.330222] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 289.330233] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 289.330247] sd 1:4:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 289.330254] sd 1:4:0:0: [sde] Write Protect is off
[ 289.330257] sd 1:4:0:0: [sde] Mode Sense: 00 3a 00 00
[ 289.330269] sd 1:4:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 289.330282] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 289.330290] sd 1:5:0:0: [sdf] Write Protect is off
[ 289.330293] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 289.330304] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 289.330317] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 289.330325] sd 1:0:0:0: [sdb] Write Protect is off
[ 289.330328] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 289.330339] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 289.330352] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 289.330359] sd 1:1:0:0: [sdc] Write Protect is off
[ 289.330362] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 289.330374] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 289.330386] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 289.330394] sd 1:2:0:0: [sdd] Write Protect is off
[ 289.330397] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 289.330408] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 289.330421] sd 1:4:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 289.330429] sd 1:4:0:0: [sde] Write Protect is off
[ 289.330431] sd 1:4:0:0: [sde] Mode Sense: 00 3a 00 00
[ 289.330443] sd 1:4:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 289.330455] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 289.330463] sd 1:5:0:0: [sdf] Write Protect is off
[ 289.330466] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 289.330477] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 381.529021] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 381.529026] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 381.529030] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 381.529033] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 381.529036] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 381.529039] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 381.529042] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 381.529047] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 381.529050] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 381.529054] ata1: SError: { 10B8B }
[ 381.529059] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 381.529064] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 381.529069] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 381.529074] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 381.529079] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 381.529085] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 381.529090] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 381.529097] ata1.15: hard resetting link
[ 386.846507] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 386.846725] ata1.00: hard resetting link
[ 387.166587] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 387.166591] ata1.01: hard resetting link
[ 387.486488] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 387.486492] ata1.02: hard resetting link
[ 387.806391] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 387.806395] ata1.03: hard resetting link
[ 388.126293] ata1.03: SATA link down (SStatus 0 SControl 310)
[ 388.126297] ata1.04: hard resetting link
[ 388.446197] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 388.446201] ata1.05: hard resetting link
[ 388.766097] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 388.766101] ata1.06: hard resetting link
[ 389.086002] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 389.086113] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 389.086117] ata1.00: revalidation failed (errno=-5)
[ 389.086122] ata1.15: hard resetting link
[ 391.285159] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 391.285360] ata1.00: hard resetting link
[ 391.605238] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 391.605242] ata1.01: hard resetting link
[ 391.925141] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 391.925145] ata1.02: hard resetting link
[ 392.245044] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 392.245048] ata1.03: hard resetting link
[ 392.564947] ata1.03: SATA link down (SStatus 0 SControl 310)
[ 392.564950] ata1.04: hard resetting link
[ 392.884850] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 392.884853] ata1.05: hard resetting link
[ 393.204750] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 393.204754] ata1.06: hard resetting link
[ 393.524655] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 393.526898] ata1.00: configured for UDMA/100
[ 393.529077] ata1.01: configured for UDMA/100
[ 393.629634] ata1.02: configured for UDMA/100
[ 393.739404] ata1.04: configured for UDMA/100
[ 393.739512] ata1.05: device is on DMA blacklist, disabling DMA
[ 393.739622] ata1.05: configured for PIO4
[ 393.739893] ata1: EH complete
[ 393.739918] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 393.739929] sd 1:0:0:0: [sdb] Write Protect is off
[ 393.739932] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 393.739945] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 393.739960] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 393.739968] sd 1:1:0:0: [sdc] Write Protect is off
[ 393.739970] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 393.739982] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 393.739996] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 393.740004] sd 1:2:0:0: [sdd] Write Protect is off
[ 393.740006] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 393.740018] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 393.740032] sd 1:4:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 393.740039] sd 1:4:0:0: [sde] Write Protect is off
[ 393.740042] sd 1:4:0:0: [sde] Mode Sense: 00 3a 00 00
[ 393.740054] sd 1:4:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 393.740067] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 393.740075] sd 1:5:0:0: [sdf] Write Protect is off
[ 393.740078] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 393.740089] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 393.740102] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 393.740109] sd 1:0:0:0: [sdb] Write Protect is off
[ 393.740112] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 393.740124] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 393.740136] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 393.740144] sd 1:1:0:0: [sdc] Write Protect is off
[ 393.740147] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 393.740158] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 393.740171] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 393.740179] sd 1:2:0:0: [sdd] Write Protect is off
[ 393.740182] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 393.740193] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 393.740206] sd 1:4:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 393.740213] sd 1:4:0:0: [sde] Write Protect is off
[ 393.740216] sd 1:4:0:0: [sde] Mode Sense: 00 3a 00 00
[ 393.740228] sd 1:4:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 393.740240] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 393.740248] sd 1:5:0:0: [sdf] Write Protect is off
[ 393.740251] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 393.740262] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[-- Attachment #3: initialboot.txt --]
[-- Type: text/plain, Size: 26986 bytes --]
[ 0.000000] Linux version 2.6.24-rc7 (root@BigMouth) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #3 Fri Jan 11 22:15:34 EST 2008
[ 0.000000] Command line: root=/dev/sda3
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff30000 (usable)
[ 0.000000] BIOS-e820: 000000007ff30000 - 000000007ff40000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ff40000 - 000000007fff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 256, 524080) 1 entries of 256 used
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000FA850, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 7FF30000, 0030 (r1 A M I OEMRSDT 6000517 MSFT 97)
[ 0.000000] ACPI: FACP 7FF30200, 0081 (r1 A M I OEMFACP 6000517 MSFT 97)
[ 0.000000] ACPI: DSDT 7FF303F0, 38EA (r1 SK8V_ SK8V_033 33 MSFT 100000D)
[ 0.000000] ACPI: FACS 7FF40000, 0040
[ 0.000000] ACPI: APIC 7FF30390, 0052 (r1 A M I OEMAPIC 6000517 MSFT 97)
[ 0.000000] ACPI: OEMB 7FF40040, 003F (r1 A M I OEMBIOS 6000517 MSFT 97)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 256, 524080) 1 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 524080
[ 0.000000] On node 0 totalpages: 523983
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 964 pages reserved
[ 0.000000] DMA zone: 2979 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7109 pages used for memmap
[ 0.000000] DMA32 zone: 512875 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7ff80000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515854
[ 0.000000] Kernel command line: root=/dev/sda3
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] TSC calibrated against PM_TIMER
[ 41.618216] time.c: Detected 1802.299 MHz processor.
[ 41.620616] Console: colour VGA+ 80x25
[ 41.620619] console [tty0] enabled
[ 41.624678] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 41.626767] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 41.627141] Checking aperture...
[ 41.627195] CPU 0: aperture @ f8000000 size 64 MB
[ 41.646942] Memory: 2059876k/2096320k available (2288k kernel code, 35684k reserved, 1034k data, 192k init)
[ 41.724181] Calibrating delay using timer specific routine.. 3608.83 BogoMIPS (lpj=7217670)
[ 41.724337] Mount-cache hash table entries: 256
[ 41.724500] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 41.724557] CPU: L2 Cache: 1024K (64 bytes/line)
[ 41.724622] CPU: AMD Opteron(tm) Processor 144 stepping 0a
[ 41.724765] ACPI: Core revision 20070126
[ 41.767576] Using local APIC timer interrupts.
[ 41.823100] APIC timer calibration result 12515974
[ 41.823102] Detected 12.515 MHz APIC timer.
[ 41.823286] net_namespace: 120 bytes
[ 41.823714] NET: Registered protocol family 16
[ 41.823905] ACPI: bus type pci registered
[ 41.823965] PCI: Using configuration type 1
[ 41.826106] ACPI: EC: Look up EC in DSDT
[ 41.829621] ACPI: Interpreter enabled
[ 41.829675] ACPI: (supports S0 S1 S3 S5)
[ 41.829887] ACPI: Using IOAPIC for interrupt routing
[ 41.836667] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 41.837405] PCI: enabled onboard AC97/MC97 devices
[ 41.837705] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 41.844265] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
[ 41.844787] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
[ 41.845307] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
[ 41.845826] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
[ 41.846345] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.846950] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.847570] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.848175] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.848777] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 41.848853] pnp: PnP ACPI init
[ 41.848910] ACPI: bus type pnp registered
[ 41.852287] pnp: PnP ACPI: found 14 devices
[ 41.852341] ACPI: ACPI bus type pnp unregistered
[ 41.852541] SCSI subsystem initialized
[ 41.852682] PCI: Using ACPI for IRQ routing
[ 41.852737] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 41.852810] PCI: Cannot allocate resource region 0 of device 0000:00:00.0
[ 41.863211] agpgart: Detected AGP bridge 0
[ 41.866722] agpgart: AGP aperture is 64M @ 0xf8000000
[ 41.867159] Time: tsc clocksource has been installed.
[ 41.875194] system 00:09: ioport range 0x295-0x296 has been reserved
[ 41.875252] system 00:09: ioport range 0x3e1-0x3e7 has been reserved
[ 41.875309] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[ 41.875366] system 00:09: ioport range 0x800-0x87f has been reserved
[ 41.875423] system 00:09: ioport range 0x400-0x41f has been reserved
[ 41.875485] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[ 41.875543] system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 41.875611] system 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
[ 41.875684] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 41.875741] system 00:0d: iomem range 0xc0000-0xdffff has been reserved
[ 41.875799] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[ 41.875856] system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
[ 41.875924] system 00:0d: iomem range 0x0-0x0 could not be reserved
[ 41.876318] PCI: Bridge: 0000:00:01.0
[ 41.876371] IO window: a000-afff
[ 41.876426] MEM window: fc500000-fcafffff
[ 41.876480] PREFETCH window: b3e00000-f3dfffff
[ 41.876552] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 41.876577] NET: Registered protocol family 2
[ 41.911201] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 41.911806] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 41.914358] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 41.914760] TCP: Hash tables configured (established 262144 bind 65536)
[ 41.914817] TCP reno registered
[ 41.923814] audit: initializing netlink socket (disabled)
[ 41.923877] audit(1200092274.256:1): initialized
[ 41.924197] io scheduler noop registered
[ 41.924251] io scheduler anticipatory registered (default)
[ 41.924306] io scheduler deadline registered
[ 41.924366] io scheduler cfq registered
[ 41.924424] PCI: VIA PCI bridge detected. Disabling DAC.
[ 41.924948] Boot video device is 0000:01:00.0
[ 41.927001] Real Time Clock Driver v1.12ac
[ 41.927117] Linux agpgart interface v0.102
[ 41.927179] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 41.927340] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 41.927484] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 41.928134] RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
[ 41.928436] loop: module loaded
[ 41.928493] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 41.928550] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 41.928654] VIA8237SATA: IDE controller (0x1106:0x3149 rev 0x80) at PCI slot 0000:00:0f.0
[ 41.928736] ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
[ 41.928853] VIA8237SATA: 100% native mode on irq 20
[ 41.928911] ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
[ 41.929060] ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
[ 41.929206] Probing IDE interface ide2...
[ 42.494969] Probing IDE interface ide3...
[ 43.062799] VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
[ 43.062878] ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
[ 43.062985] VP_IDE: not 100% native mode: will probe irqs later
[ 43.063047] VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
[ 43.063117] ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
[ 43.063266] ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
[ 43.063412] Probing IDE interface ide0...
[ 43.478770] hdb: Maxtor 4G160J8, ATA DISK drive
[ 43.814667] hda: ST3200822A, ATA DISK drive
[ 43.814763] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 43.814984] hda: UDMA/100 mode selected
[ 43.815332] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 43.815442] hdb: UDMA/133 mode selected
[ 43.815625] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 43.815777] Probing IDE interface ide1...
[ 44.734388] hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
[ 45.518150] hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
[ 45.518322] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 45.518389] hdc: UDMA/33 mode selected
[ 45.518508] hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 45.518741] hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
[ 45.518809] hdd: UDMA/33 mode selected
[ 45.519116] ide1 at 0x170-0x177,0x376 on irq 15
[ 45.519350] Probing IDE interface ide2...
[ 46.085878] Probing IDE interface ide3...
[ 46.653726] hda: max request size: 512KiB
[ 46.654211] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
[ 46.654473] hda: cache flushes supported
[ 46.654549] hda: hda1 hda2
[ 46.668350] hdb: max request size: 512KiB
[ 46.675618] hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63
[ 46.675761] hdb: cache flushes not supported
[ 46.675830] hdb: hdb1
[ 46.687057] hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
[ 46.687340] Uniform CD-ROM driver Revision: 3.20
[ 47.971389] hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
[ 47.982729] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 53.191727] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 53.191729] <Adaptec 29160N Ultra160 SCSI adapter>
[ 53.191731] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
[ 53.191732]
[ 53.195663] scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
[ 53.195737] scsi0:A:0:0: Tagged Queuing enabled. Depth 32
[ 53.195836] target0:0:0: Beginning Domain Validation
[ 53.203996] target0:0:0: wide asynchronous
[ 53.210176] target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
[ 53.220943] target0:0:0: Ending Domain Validation
[ 53.743274] scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
[ 53.743349] target0:0:3: Beginning Domain Validation
[ 53.755769] target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
[ 53.764138] target0:0:3: Domain Validation skipping write tests
[ 53.764193] target0:0:3: Ending Domain Validation
[ 56.584537] Driver 'sd' needs updating - please use bus_type methods
[ 56.585434] sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
[ 56.586616] sd 0:0:0:0: [sda] Write Protect is off
[ 56.586670] sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
[ 56.588354] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 56.589219] sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
[ 56.590401] sd 0:0:0:0: [sda] Write Protect is off
[ 56.590455] sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
[ 56.592163] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 56.592231] sda: sda1 sda2 sda3
[ 56.596310] sd 0:0:0:0: [sda] Attached SCSI disk
[ 56.596372] Driver 'sr' needs updating - please use bus_type methods
[ 56.631073] sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
[ 56.631173] sr 0:0:3:0: Attached scsi CD-ROM sr0
[ 56.631239] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 56.631658] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 56.631715] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 56.631877] mice: PS/2 mouse device common for all mice
[ 56.661791] input: AT Translated Set 2 keyboard as /class/input/input0
[ 56.689904] TCP cubic registered
[ 56.689962] NET: Registered protocol family 1
[ 56.690026] NET: Registered protocol family 17
[ 56.690112] NET: Registered protocol family 33
[ 56.690306] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 57.086790] input: ImPS/2 Generic Wheel Mouse as /class/input/input1
[ 57.213499] ReiserFS: sda3: found reiserfs format "3.6" with standard journal
[ 57.213561] ReiserFS: sda3: using ordered data mode
[ 57.216529] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 57.218121] ReiserFS: sda3: checking transaction log (sda3)
[ 57.244588] ReiserFS: sda3: Using r5 hash to sort names
[ 57.244669] VFS: Mounted root (reiserfs filesystem) readonly.
[ 57.244739] Freeing unused kernel memory: 192k freed
[ 59.406317] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 59.406341] sr 0:0:3:0: Attached scsi generic sg1 type 5
[ 59.428553] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 59.508971] libata version 3.00 loaded.
[ 59.737302] usbcore: registered new interface driver usbfs
[ 59.737335] usbcore: registered new interface driver hub
[ 59.773362] usbcore: registered new device driver usb
[ 59.809187] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 59.822712] USB Universal Host Controller Interface driver v3.0
[ 59.823317] input: Power Button (FF) as /class/input/input2
[ 59.853767] ACPI: Power Button (FF) [PWRF]
[ 59.853856] input: Power Button (CM) as /class/input/input3
[ 59.861345] sata_sil24 0000:00:0c.0: version 1.1
[ 59.861367] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 59.861780] PCI: Disallowing DAC for device 0000:00:0c.0
[ 59.877746] ACPI: Power Button (CM) [PWRB]
[ 59.877823] input: Sleep Button (CM) as /class/input/input4
[ 59.882329] scsi1 : sata_sil24
[ 59.896674] scsi2 : sata_sil24
[ 59.909750] ACPI: Sleep Button (CM) [SLPB]
[ 59.929168] scsi3 : sata_sil24
[ 59.952335] scsi4 : sata_sil24
[ 59.952398] ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
[ 59.952402] ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
[ 59.952406] ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
[ 59.952409] ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
[ 60.536982] input: PC Speaker as /class/input/input5
[ 60.651796] Floppy drive(s): fd0 is 1.44M
[ 60.669365] FDC 0 is a post-1991 82077
[ 60.672110] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 60.672228] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 61.129412] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
[ 62.149016] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 62.149161] ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
[ 62.149354] ata1.00: hard resetting link
[ 62.469069] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 62.469071] ata1.01: hard resetting link
[ 62.788977] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.788984] ata1.02: hard resetting link
[ 63.108875] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 63.108878] ata1.03: hard resetting link
[ 63.428780] ata1.03: SATA link down (SStatus 0 SControl 320)
[ 63.428783] ata1.04: hard resetting link
[ 63.748685] ata1.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 63.748692] ata1.05: hard resetting link
[ 64.068583] ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 64.068586] ata1.06: hard resetting link
[ 64.388488] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 64.389577] ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 64.389580] ata1.00: 586072368 sectors, multi 16: LBA48
[ 64.389583] ata1.00: applying bridge limits
[ 64.390715] ata1.00: configured for UDMA/100
[ 64.391771] ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 64.391773] ata1.01: 586072368 sectors, multi 0: LBA48
[ 64.391775] ata1.01: applying bridge limits
[ 64.392913] ata1.01: configured for UDMA/100
[ 64.438134] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 64.438137] ata1.02: 586072368 sectors, multi 0: LBA48
[ 64.438139] ata1.02: applying bridge limits
[ 64.496278] ata1.02: configured for UDMA/100
[ 64.539472] ata1.04: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 64.539475] ata1.04: 586072368 sectors, multi 0: LBA48
[ 64.539477] ata1.04: applying bridge limits
[ 64.597758] ata1.04: configured for UDMA/100
[ 64.597829] ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
[ 64.597832] ata1.05: 640 sectors, multi 1: LBA
[ 64.597839] ata1.05: device is on DMA blacklist, disabling DMA
[ 64.597929] ata1.05: configured for PIO4
[ 64.597969] ata1: EH complete
[ 66.675642] ata2: SATA link down (SStatus 0 SControl 0)
[ 68.755011] ata3: SATA link down (SStatus 0 SControl 0)
[ 70.834380] ata4: SATA link down (SStatus 0 SControl 0)
[ 70.834495] scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.834908] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.834919] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.834922] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.834934] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.834978] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.834985] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.834987] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.834998] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.835002] sdb: sdb1
[ 70.843975] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 70.844011] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 70.844453] scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.844729] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.844736] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.844739] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.844750] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.844779] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.844786] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.844788] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.844799] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.844802] sdc: sdc1
[ 70.863628] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 70.863659] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 70.864129] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.864190] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.864197] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.864200] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.864211] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.864240] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.864247] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.864249] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.864260] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.864263] sdd: sdd1
[ 70.881739] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 70.881772] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 70.881818] scsi 1:4:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.881877] sd 1:4:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.881884] sd 1:4:0:0: [sde] Write Protect is off
[ 70.881886] sd 1:4:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.881897] sd 1:4:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.882646] sd 1:4:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.882654] sd 1:4:0:0: [sde] Write Protect is off
[ 70.882656] sd 1:4:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.882667] sd 1:4:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.882670] sde: sde1
[ 70.898341] sd 1:4:0:0: [sde] Attached SCSI disk
[ 70.898375] sd 1:4:0:0: Attached scsi generic sg5 type 0
[ 70.898421] scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 70.898480] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.898487] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.898490] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.898501] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.898530] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.898537] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.898539] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.898550] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.898553] sdf: unknown partition table
[ 70.899398] sd 1:5:0:0: [sdf] Attached SCSI disk
[ 70.899430] sd 1:5:0:0: Attached scsi generic sg6 type 0
[ 70.899727] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.899738] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 70.899929] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 70.899958] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
[ 70.900097] usb usb1: configuration #1 chosen from 1 choice
[ 70.900124] hub 1-0:1.0: USB hub found
[ 70.900133] hub 1-0:1.0: 2 ports detected
[ 71.002471] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 71.002485] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 71.002509] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 71.002532] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 71.002652] usb usb2: configuration #1 chosen from 1 choice
[ 71.002678] hub 2-0:1.0: USB hub found
[ 71.002685] hub 2-0:1.0: 2 ports detected
[ 71.106425] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.106439] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 71.106464] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 71.106487] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 71.106608] usb usb3: configuration #1 chosen from 1 choice
[ 71.106632] hub 3-0:1.0: USB hub found
[ 71.106640] hub 3-0:1.0: 2 ports detected
[ 71.210424] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.210438] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 71.210463] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 71.210487] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 71.210606] usb usb4: configuration #1 chosen from 1 choice
[ 71.210631] hub 4-0:1.0: USB hub found
[ 71.210639] hub 4-0:1.0: 2 ports detected
[ 71.314524] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 71.316772] Audigy2 value: Special config.
[ 71.329677] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 71.330044] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 71.330104] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 71.330152] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
[ 71.338231] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 71.338350] usb usb5: configuration #1 chosen from 1 choice
[ 71.338377] hub 5-0:1.0: USB hub found
[ 71.338387] hub 5-0:1.0: 8 ports detected
[ 73.047330] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 73.047334] Copyright (c) 1999-2006 Intel Corporation.
[ 73.047376] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 73.047381] PCI: Disallowing DAC for device 0000:00:0e.0
[ 73.307233] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 73.482707] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 73.641789] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 73.641802] ReiserFS: hdb1: using ordered data mode
[ 73.677157] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 73.678508] ReiserFS: hdb1: checking transaction log (hdb1)
[ 73.795920] ReiserFS: hdb1: Using r5 hash to sort names
[ 73.842916] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 73.842927] ReiserFS: hda2: using ordered data mode
[ 73.847744] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 73.849101] ReiserFS: hda2: checking transaction log (hda2)
[ 73.903713] ReiserFS: hda2: Using r5 hash to sort names
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-11 23:13 ` Andrew Ryder
@ 2008-01-13 5:10 ` Tejun Heo
2008-01-13 19:01 ` Andrew Ryder
2008-01-14 19:07 ` Gaston, Jason D
0 siblings, 2 replies; 26+ messages in thread
From: Tejun Heo @ 2008-01-13 5:10 UTC (permalink / raw)
To: Andrew Ryder; +Cc: Gaston, Jason D, linux-ide
Andrew Ryder wrote:
> Tejun,
>
> No problem. I should be thanking you and your team for all the hard work
> writing the drivers for the hardware..
>
> I think this patch might have solved the issue. I did a quick test: warm
> rebooted and turned the 4726 on and off 3 times and all disks were
> successfully detected each time. I'll do a more thorough test tomorrow
> or Sunday.
Great. I forwarded the patch for #upstream-fixes as the patch is in the
right direction whether it fully fixes your problem or not. Please
lemme know the test result.
Gaston, for the initial detection failure messages when connected to ICH
AHCI, I don't really have much idea what's going on or how to fix it. I
suspect it's related to initial FISes from drives arriving
asynchronously after hard resets but can't tell much without bus
analyzer. Anyways, as EH can handle the case quickly enough, I guess we
can leave it at that for now. If you have ideas on what's going on or
how to fix it, please lemme know.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-13 5:10 ` Tejun Heo
@ 2008-01-13 19:01 ` Andrew Ryder
2008-01-14 0:35 ` Tejun Heo
2008-01-14 19:07 ` Gaston, Jason D
1 sibling, 1 reply; 26+ messages in thread
From: Andrew Ryder @ 2008-01-13 19:01 UTC (permalink / raw)
To: Tejun Heo; +Cc: Gaston, Jason D, linux-ide
[-- Attachment #1: Type: text/plain, Size: 2923 bytes --]
Tejun,
I have completed some of the testing, things were working fine.. then
something died. It will not even recognize the 4726 anymore. During book
when the HBA does it scan nor in windows 2000 does anything work or be
recognized.
I will have a new eSATA cable this week sometime, maybe a pin got
shmucked if lucky. I've attached the logs of the good and the gone dead.
Here's the testing procedure:
Sata 4726 testing: 4726 on at boot:
1. Rebooted the computer, powered the sata on 4726 before booting.
Notes: Everything works
File: 1_Bootup.log
2. Turn 4726 off, wait 10 seconds, turn 4726 on
Notes: Works
3. Repeat #2.
Notes: Works
File: 2_PowerOnOffTwice.log
4. Unplug 4726, wait 10 seconds, plug back in (leave 4726 powered up)
Notes: Works
File: 3_PlugUnplug.txt
5. Power 4726 off, wait 10 seconds, power back on 4726
Notes: Something crapped out. (Timestamp 404-505). LED status lights
dark
6. Repeat step #5
Notes: Repeating did not fix things. Same failures.
File: 4_PowerOnOffTwice.log
7. Unplugged and re-plugged 4726 on same port
Notes: Did not do a thing. Did not even generate a kernel message..
(Timestamp between 688 and 776)
8. Unplugged from port 1 and plugged 4726 into port 2
Same results as #7. (Timestamp 776-836)
9. Powered unit off, unplugged cable from HBA, waited 10 seconds,
plugged cable
back into HBA and powered up.
Notes: Nothing. No kernel messages or activity.
10. Unloaded sata_sil24 module.
File: 5_Broken.log
11. Reloaded sata_sil24
Notes: Still unresponsive.
File: 6_ModuleReload.log
12. Repeated steps 10 & 11 but removed sata_sil24 and libata
Notes: Unresponsive. LED status lights are still dark also since the
initial failure.
File 7_ModuleReload2.log
Tejun Heo wrote:
> Andrew Ryder wrote:
>
>> Tejun,
>>
>> No problem. I should be thanking you and your team for all the hard work
>> writing the drivers for the hardware..
>>
>> I think this patch might have solved the issue. I did a quick test: warm
>> rebooted and turned the 4726 on and off 3 times and all disks were
>> successfully detected each time. I'll do a more thorough test tomorrow
>> or Sunday.
>>
>
> Great. I forwarded the patch for #upstream-fixes as the patch is in the
> right direction whether it fully fixes your problem or not. Please
> lemme know the test result.
>
> Gaston, for the initial detection failure messages when connected to ICH
> AHCI, I don't really have much idea what's going on or how to fix it. I
> suspect it's related to initial FISes from drives arriving
> asynchronously after hard resets but can't tell much without bus
> analyzer. Anyways, as EH can handle the case quickly enough, I guess we
> can leave it at that for now. If you have ideas on what's going on or
> how to fix it, please lemme know.
>
> Thanks.
>
>
[-- Attachment #2: 1_Bootup.log --]
[-- Type: text/plain, Size: 27311 bytes --]
[ 0.000000] Linux version 2.6.24-rc7 (root@BigMouth) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #3 Fri Jan 11 22:15:34 EST 2008
[ 0.000000] Command line: root=/dev/sda3
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff30000 (usable)
[ 0.000000] BIOS-e820: 000000007ff30000 - 000000007ff40000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ff40000 - 000000007fff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 256, 524080) 1 entries of 256 used
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000FA850, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 7FF30000, 0030 (r1 A M I OEMRSDT 6000517 MSFT 97)
[ 0.000000] ACPI: FACP 7FF30200, 0081 (r1 A M I OEMFACP 6000517 MSFT 97)
[ 0.000000] ACPI: DSDT 7FF303F0, 38EA (r1 SK8V_ SK8V_033 33 MSFT 100000D)
[ 0.000000] ACPI: FACS 7FF40000, 0040
[ 0.000000] ACPI: APIC 7FF30390, 0052 (r1 A M I OEMAPIC 6000517 MSFT 97)
[ 0.000000] ACPI: OEMB 7FF40040, 003F (r1 A M I OEMBIOS 6000517 MSFT 97)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 256, 524080) 1 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 524080
[ 0.000000] On node 0 totalpages: 523983
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 964 pages reserved
[ 0.000000] DMA zone: 2979 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7109 pages used for memmap
[ 0.000000] DMA32 zone: 512875 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7ff80000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515854
[ 0.000000] Kernel command line: root=/dev/sda3
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] TSC calibrated against PM_TIMER
[ 41.449000] time.c: Detected 1802.299 MHz processor.
[ 41.451400] Console: colour VGA+ 80x25
[ 41.451403] console [tty0] enabled
[ 41.455463] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 41.457554] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 41.457929] Checking aperture...
[ 41.457983] CPU 0: aperture @ f8000000 size 64 MB
[ 41.477727] Memory: 2059876k/2096320k available (2288k kernel code, 35684k reserved, 1034k data, 192k init)
[ 41.554966] Calibrating delay using timer specific routine.. 3608.83 BogoMIPS (lpj=7217667)
[ 41.555122] Mount-cache hash table entries: 256
[ 41.555285] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 41.555342] CPU: L2 Cache: 1024K (64 bytes/line)
[ 41.555407] CPU: AMD Opteron(tm) Processor 144 stepping 0a
[ 41.555550] ACPI: Core revision 20070126
[ 41.598361] Using local APIC timer interrupts.
[ 41.653885] APIC timer calibration result 12515971
[ 41.653887] Detected 12.515 MHz APIC timer.
[ 41.654071] net_namespace: 120 bytes
[ 41.654499] NET: Registered protocol family 16
[ 41.654689] ACPI: bus type pci registered
[ 41.654749] PCI: Using configuration type 1
[ 41.656890] ACPI: EC: Look up EC in DSDT
[ 41.660406] ACPI: Interpreter enabled
[ 41.660459] ACPI: (supports S0 S1 S3 S5)
[ 41.660672] ACPI: Using IOAPIC for interrupt routing
[ 41.667451] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 41.668190] PCI: enabled onboard AC97/MC97 devices
[ 41.668490] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 41.675050] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
[ 41.675571] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
[ 41.676091] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
[ 41.676610] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
[ 41.677129] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.677735] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.678354] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.678960] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 41.679561] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 41.679638] pnp: PnP ACPI init
[ 41.679695] ACPI: bus type pnp registered
[ 41.683072] pnp: PnP ACPI: found 14 devices
[ 41.683125] ACPI: ACPI bus type pnp unregistered
[ 41.683325] SCSI subsystem initialized
[ 41.683467] PCI: Using ACPI for IRQ routing
[ 41.683521] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 41.683595] PCI: Cannot allocate resource region 0 of device 0000:00:00.0
[ 41.693996] agpgart: Detected AGP bridge 0
[ 41.697506] agpgart: AGP aperture is 64M @ 0xf8000000
[ 41.697944] Time: tsc clocksource has been installed.
[ 41.705979] system 00:09: ioport range 0x295-0x296 has been reserved
[ 41.706037] system 00:09: ioport range 0x3e1-0x3e7 has been reserved
[ 41.706094] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[ 41.706151] system 00:09: ioport range 0x800-0x87f has been reserved
[ 41.706208] system 00:09: ioport range 0x400-0x41f has been reserved
[ 41.706270] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[ 41.706328] system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 41.706396] system 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
[ 41.706469] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 41.706526] system 00:0d: iomem range 0xc0000-0xdffff has been reserved
[ 41.706584] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[ 41.706641] system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
[ 41.706709] system 00:0d: iomem range 0x0-0x0 could not be reserved
[ 41.707104] PCI: Bridge: 0000:00:01.0
[ 41.707157] IO window: a000-afff
[ 41.707211] MEM window: fc500000-fcafffff
[ 41.707265] PREFETCH window: b3e00000-f3dfffff
[ 41.707337] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 41.707362] NET: Registered protocol family 2
[ 41.741986] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 41.742592] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 41.745143] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 41.745545] TCP: Hash tables configured (established 262144 bind 65536)
[ 41.745602] TCP reno registered
[ 41.754600] audit: initializing netlink socket (disabled)
[ 41.754662] audit(1200226061.256:1): initialized
[ 41.754982] io scheduler noop registered
[ 41.755036] io scheduler anticipatory registered (default)
[ 41.755091] io scheduler deadline registered
[ 41.755152] io scheduler cfq registered
[ 41.755209] PCI: VIA PCI bridge detected. Disabling DAC.
[ 41.755733] Boot video device is 0000:01:00.0
[ 41.757787] Real Time Clock Driver v1.12ac
[ 41.757902] Linux agpgart interface v0.102
[ 41.757965] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 41.758125] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 41.758270] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 41.758919] RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
[ 41.759221] loop: module loaded
[ 41.759278] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 41.759335] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 41.759439] VIA8237SATA: IDE controller (0x1106:0x3149 rev 0x80) at PCI slot 0000:00:0f.0
[ 41.759522] ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
[ 41.759638] VIA8237SATA: 100% native mode on irq 20
[ 41.759696] ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
[ 41.759845] ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
[ 41.759992] Probing IDE interface ide2...
[ 42.325754] Probing IDE interface ide3...
[ 42.893584] VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
[ 42.893663] ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
[ 42.893770] VP_IDE: not 100% native mode: will probe irqs later
[ 42.893832] VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
[ 42.893902] ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
[ 42.894051] ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
[ 42.894197] Probing IDE interface ide0...
[ 43.309555] hdb: Maxtor 4G160J8, ATA DISK drive
[ 43.645452] hda: ST3200822A, ATA DISK drive
[ 43.645548] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 43.645778] hda: UDMA/100 mode selected
[ 43.646122] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 43.646215] hdb: UDMA/133 mode selected
[ 43.646398] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 43.646550] Probing IDE interface ide1...
[ 44.565173] hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
[ 45.348936] hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
[ 45.349107] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 45.349192] hdc: UDMA/33 mode selected
[ 45.349311] hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 45.349499] hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
[ 45.349567] hdd: UDMA/33 mode selected
[ 45.349873] ide1 at 0x170-0x177,0x376 on irq 15
[ 45.350107] Probing IDE interface ide2...
[ 45.916663] Probing IDE interface ide3...
[ 46.484512] hda: max request size: 512KiB
[ 46.485016] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
[ 46.485278] hda: cache flushes supported
[ 46.485354] hda: hda1 hda2
[ 46.494758] hdb: max request size: 512KiB
[ 46.502076] hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63
[ 46.502219] hdb: cache flushes not supported
[ 46.502288] hdb: hdb1
[ 46.516013] hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
[ 46.516295] Uniform CD-ROM driver Revision: 3.20
[ 47.825381] hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
[ 47.836721] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 53.046505] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 53.046507] <Adaptec 29160N Ultra160 SCSI adapter>
[ 53.046508] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
[ 53.046510]
[ 53.050435] scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
[ 53.050509] scsi0:A:0:0: Tagged Queuing enabled. Depth 32
[ 53.050608] target0:0:0: Beginning Domain Validation
[ 53.058792] target0:0:0: wide asynchronous
[ 53.064974] target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
[ 53.075742] target0:0:0: Ending Domain Validation
[ 53.598425] scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
[ 53.598499] target0:0:3: Beginning Domain Validation
[ 53.611738] target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
[ 53.619071] target0:0:3: Domain Validation skipping write tests
[ 53.619127] target0:0:3: Ending Domain Validation
[ 56.438680] Driver 'sd' needs updating - please use bus_type methods
[ 56.439575] sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
[ 56.440757] sd 0:0:0:0: [sda] Write Protect is off
[ 56.440811] sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
[ 56.442520] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 56.443360] sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
[ 56.444542] sd 0:0:0:0: [sda] Write Protect is off
[ 56.444596] sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
[ 56.446306] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 56.446375] sda: sda1 sda2 sda3
[ 56.451055] sd 0:0:0:0: [sda] Attached SCSI disk
[ 56.451117] Driver 'sr' needs updating - please use bus_type methods
[ 56.486032] sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
[ 56.486132] sr 0:0:3:0: Attached scsi CD-ROM sr0
[ 56.486199] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 56.486617] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 56.486674] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 56.486836] mice: PS/2 mouse device common for all mice
[ 56.516687] input: AT Translated Set 2 keyboard as /class/input/input0
[ 56.544551] TCP cubic registered
[ 56.544609] NET: Registered protocol family 1
[ 56.544673] NET: Registered protocol family 17
[ 56.544759] NET: Registered protocol family 33
[ 56.544953] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 56.951406] input: ImPS/2 Generic Wheel Mouse as /class/input/input1
[ 57.068218] ReiserFS: sda3: found reiserfs format "3.6" with standard journal
[ 57.068281] ReiserFS: sda3: using ordered data mode
[ 57.071275] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 57.072868] ReiserFS: sda3: checking transaction log (sda3)
[ 57.099334] ReiserFS: sda3: Using r5 hash to sort names
[ 57.099415] VFS: Mounted root (reiserfs filesystem) readonly.
[ 57.099484] Freeing unused kernel memory: 192k freed
[ 59.284316] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 59.284339] sr 0:0:3:0: Attached scsi generic sg1 type 5
[ 59.319755] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 59.398651] libata version 3.00 loaded.
[ 59.500592] usbcore: registered new interface driver usbfs
[ 59.500623] usbcore: registered new interface driver hub
[ 59.530833] usbcore: registered new device driver usb
[ 59.676096] input: Power Button (FF) as /class/input/input2
[ 59.677104] USB Universal Host Controller Interface driver v3.0
[ 59.688607] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 59.700544] ACPI: Power Button (FF) [PWRF]
[ 59.700633] input: Power Button (CM) as /class/input/input3
[ 59.720540] ACPI: Power Button (CM) [PWRB]
[ 59.720617] input: Sleep Button (CM) as /class/input/input4
[ 59.759265] sata_sil24 0000:00:0c.0: version 1.1
[ 59.759287] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 59.759606] PCI: Disallowing DAC for device 0000:00:0c.0
[ 59.760618] ACPI: Sleep Button (CM) [SLPB]
[ 59.779041] scsi1 : sata_sil24
[ 59.800462] scsi2 : sata_sil24
[ 59.822270] scsi3 : sata_sil24
[ 59.832388] scsi4 : sata_sil24
[ 59.832473] ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
[ 59.832477] ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
[ 59.832480] ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
[ 59.832484] ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
[ 60.346837] input: PC Speaker as /class/input/input5
[ 60.504139] Floppy drive(s): fd0 is 1.44M
[ 60.521457] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 60.521575] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 60.524072] FDC 0 is a post-1991 82077
[ 61.028170] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
[ 62.031786] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 62.031931] ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
[ 62.032124] ata1.00: hard resetting link
[ 62.351844] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 62.351851] ata1.01: hard resetting link
[ 62.671742] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.671745] ata1.02: hard resetting link
[ 62.991645] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.991647] ata1.03: hard resetting link
[ 63.311554] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 63.311561] ata1.04: hard resetting link
[ 63.631453] ata1.04: SATA link down (SStatus 0 SControl 320)
[ 63.631456] ata1.05: hard resetting link
[ 63.951352] ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 63.951355] ata1.06: hard resetting link
[ 64.272205] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 64.273279] ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 64.273282] ata1.00: 586072368 sectors, multi 16: LBA48
[ 64.273285] ata1.00: applying bridge limits
[ 64.274423] ata1.00: configured for UDMA/100
[ 64.276119] ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 64.276122] ata1.01: 586072368 sectors, multi 0: LBA48
[ 64.276125] ata1.01: applying bridge limits
[ 64.277264] ata1.01: configured for UDMA/100
[ 64.323947] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 64.323950] ata1.02: 586072368 sectors, multi 0: LBA48
[ 64.323952] ata1.02: applying bridge limits
[ 64.382089] ata1.02: configured for UDMA/100
[ 64.426133] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 64.426136] ata1.03: 586072368 sectors, multi 0: LBA48
[ 64.426138] ata1.03: applying bridge limits
[ 64.484410] ata1.03: configured for UDMA/100
[ 64.484478] ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
[ 64.484480] ata1.05: 640 sectors, multi 1: LBA
[ 64.484486] ata1.05: device is on DMA blacklist, disabling DMA
[ 64.484575] ata1.05: configured for PIO4
[ 64.484615] ata1: EH complete
[ 66.562409] ata2: SATA link down (SStatus 0 SControl 0)
[ 68.641778] ata3: SATA link down (SStatus 0 SControl 0)
[ 70.721147] ata4: SATA link down (SStatus 0 SControl 0)
[ 70.721260] scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.721669] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.721680] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.721683] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.721695] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.721740] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.721747] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.721750] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.721761] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.721765] sdb: sdb1
[ 70.728578] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 70.728614] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 70.729063] scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.729336] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.729343] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.729346] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.729357] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.729388] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.729395] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.729398] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.729409] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.729411] sdc: sdc1
[ 70.751335] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 70.751366] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 70.751842] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.751903] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.751911] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.751913] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.751924] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.751953] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.751960] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.751963] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.751974] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.751977] sdd: sdd1
[ 70.767637] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 70.767670] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 70.767716] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.767775] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.767782] sd 1:3:0:0: [sde] Write Protect is off
[ 70.767785] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.767796] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.768539] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.768546] sd 1:3:0:0: [sde] Write Protect is off
[ 70.768549] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.768560] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.768563] sde: sde1
[ 70.785093] sd 1:3:0:0: [sde] Attached SCSI disk
[ 70.785128] sd 1:3:0:0: Attached scsi generic sg5 type 0
[ 70.785174] scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 70.785234] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.785241] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.785244] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.785255] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.785284] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.785291] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.785293] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.785304] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.785307] sdf: unknown partition table
[ 70.786159] sd 1:5:0:0: [sdf] Attached SCSI disk
[ 70.786191] sd 1:5:0:0: Attached scsi generic sg6 type 0
[ 70.786363] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 70.786553] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 70.786744] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
[ 70.786795] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
[ 70.797142] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 70.797280] usb usb1: configuration #1 chosen from 1 choice
[ 70.797308] hub 1-0:1.0: USB hub found
[ 70.797317] hub 1-0:1.0: 8 ports detected
[ 70.901323] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.901336] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 70.901363] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 70.901386] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
[ 70.901506] usb usb2: configuration #1 chosen from 1 choice
[ 70.901531] hub 2-0:1.0: USB hub found
[ 70.901539] hub 2-0:1.0: 2 ports detected
[ 71.005191] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 71.005204] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 71.005229] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 71.005252] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 71.005373] usb usb3: configuration #1 chosen from 1 choice
[ 71.005398] hub 3-0:1.0: USB hub found
[ 71.005405] hub 3-0:1.0: 2 ports detected
[ 71.109172] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.109185] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 71.109211] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 71.109235] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 71.109351] usb usb4: configuration #1 chosen from 1 choice
[ 71.109376] hub 4-0:1.0: USB hub found
[ 71.109383] hub 4-0:1.0: 2 ports detected
[ 71.213117] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.213130] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 71.213155] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 71.213179] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 71.213299] usb usb5: configuration #1 chosen from 1 choice
[ 71.213325] hub 5-0:1.0: USB hub found
[ 71.213332] hub 5-0:1.0: 2 ports detected
[ 71.317585] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 71.319838] Audigy2 value: Special config.
[ 73.765264] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 73.765268] Copyright (c) 1999-2006 Intel Corporation.
[ 73.765309] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 73.765314] PCI: Disallowing DAC for device 0000:00:0e.0
[ 74.025736] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 74.201234] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 74.355702] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 74.355715] ReiserFS: hdb1: using ordered data mode
[ 74.392680] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.394057] ReiserFS: hdb1: checking transaction log (hdb1)
[ 74.489291] ReiserFS: hdb1: Using r5 hash to sort names
[ 74.553988] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 74.553998] ReiserFS: hda2: using ordered data mode
[ 74.558818] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.560151] ReiserFS: hda2: checking transaction log (hda2)
[ 74.623128] ReiserFS: hda2: Using r5 hash to sort names
[ 80.456682] hda: UDMA/100 mode selected
[ 80.460729] hdb: UDMA/133 mode selected
[ 80.515263] hdc: UDMA/33 mode selected
[ 80.532803] hdd: UDMA/33 mode selected
[ 83.053804] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 87.342494] w83627hf: Found W83697HF chip at 0x290
[-- Attachment #3: 2_PowerOnOffTwice.log --]
[-- Type: text/plain, Size: 31301 bytes --]
5 wanted PIO255(auto-tune) selected PIO4
[ 43.645778] hda: UDMA/100 mode selected
[ 43.646122] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 43.646215] hdb: UDMA/133 mode selected
[ 43.646398] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 43.646550] Probing IDE interface ide1...
[ 44.565173] hdd: ASUS DVD-E616P2, ATAPI CD/DVD-ROM drive
[ 45.348936] hdc: ASUS DRW-0402P/D, ATAPI CD/DVD-ROM drive
[ 45.349107] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 45.349192] hdc: UDMA/33 mode selected
[ 45.349311] hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 45.349499] hdd: drive side 80-wire cable detection failed, limiting max speed to UDMA33
[ 45.349567] hdd: UDMA/33 mode selected
[ 45.349873] ide1 at 0x170-0x177,0x376 on irq 15
[ 45.350107] Probing IDE interface ide2...
[ 45.916663] Probing IDE interface ide3...
[ 46.484512] hda: max request size: 512KiB
[ 46.485016] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
[ 46.485278] hda: cache flushes supported
[ 46.485354] hda: hda1 hda2
[ 46.494758] hdb: max request size: 512KiB
[ 46.502076] hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63
[ 46.502219] hdb: cache flushes not supported
[ 46.502288] hdb: hdb1
[ 46.516013] hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
[ 46.516295] Uniform CD-ROM driver Revision: 3.20
[ 47.825381] hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
[ 47.836721] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 53.046505] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 53.046507] <Adaptec 29160N Ultra160 SCSI adapter>
[ 53.046508] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
[ 53.046510]
[ 53.050435] scsi 0:0:0:0: Direct-Access SEAGATE ST318452LW 0004 PQ: 0 ANSI: 3
[ 53.050509] scsi0:A:0:0: Tagged Queuing enabled. Depth 32
[ 53.050608] target0:0:0: Beginning Domain Validation
[ 53.058792] target0:0:0: wide asynchronous
[ 53.064974] target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
[ 53.075742] target0:0:0: Ending Domain Validation
[ 53.598425] scsi 0:0:3:0: CD-ROM YAMAHA CRW8824S 1.00 PQ: 0 ANSI: 2
[ 53.598499] target0:0:3: Beginning Domain Validation
[ 53.611738] target0:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
[ 53.619071] target0:0:3: Domain Validation skipping write tests
[ 53.619127] target0:0:3: Ending Domain Validation
[ 56.438680] Driver 'sd' needs updating - please use bus_type methods
[ 56.439575] sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
[ 56.440757] sd 0:0:0:0: [sda] Write Protect is off
[ 56.440811] sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
[ 56.442520] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 56.443360] sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
[ 56.444542] sd 0:0:0:0: [sda] Write Protect is off
[ 56.444596] sd 0:0:0:0: [sda] Mode Sense: a3 00 10 08
[ 56.446306] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 56.446375] sda: sda1 sda2 sda3
[ 56.451055] sd 0:0:0:0: [sda] Attached SCSI disk
[ 56.451117] Driver 'sr' needs updating - please use bus_type methods
[ 56.486032] sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
[ 56.486132] sr 0:0:3:0: Attached scsi CD-ROM sr0
[ 56.486199] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 56.486617] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 56.486674] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 56.486836] mice: PS/2 mouse device common for all mice
[ 56.516687] input: AT Translated Set 2 keyboard as /class/input/input0
[ 56.544551] TCP cubic registered
[ 56.544609] NET: Registered protocol family 1
[ 56.544673] NET: Registered protocol family 17
[ 56.544759] NET: Registered protocol family 33
[ 56.544953] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 56.951406] input: ImPS/2 Generic Wheel Mouse as /class/input/input1
[ 57.068218] ReiserFS: sda3: found reiserfs format "3.6" with standard journal
[ 57.068281] ReiserFS: sda3: using ordered data mode
[ 57.071275] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 57.072868] ReiserFS: sda3: checking transaction log (sda3)
[ 57.099334] ReiserFS: sda3: Using r5 hash to sort names
[ 57.099415] VFS: Mounted root (reiserfs filesystem) readonly.
[ 57.099484] Freeing unused kernel memory: 192k freed
[ 59.284316] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 59.284339] sr 0:0:3:0: Attached scsi generic sg1 type 5
[ 59.319755] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 59.398651] libata version 3.00 loaded.
[ 59.500592] usbcore: registered new interface driver usbfs
[ 59.500623] usbcore: registered new interface driver hub
[ 59.530833] usbcore: registered new device driver usb
[ 59.676096] input: Power Button (FF) as /class/input/input2
[ 59.677104] USB Universal Host Controller Interface driver v3.0
[ 59.688607] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fd400000-fd4007ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 59.700544] ACPI: Power Button (FF) [PWRF]
[ 59.700633] input: Power Button (CM) as /class/input/input3
[ 59.720540] ACPI: Power Button (CM) [PWRB]
[ 59.720617] input: Sleep Button (CM) as /class/input/input4
[ 59.759265] sata_sil24 0000:00:0c.0: version 1.1
[ 59.759287] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 59.759606] PCI: Disallowing DAC for device 0000:00:0c.0
[ 59.760618] ACPI: Sleep Button (CM) [SLPB]
[ 59.779041] scsi1 : sata_sil24
[ 59.800462] scsi2 : sata_sil24
[ 59.822270] scsi3 : sata_sil24
[ 59.832388] scsi4 : sata_sil24
[ 59.832473] ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
[ 59.832477] ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
[ 59.832480] ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
[ 59.832484] ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
[ 60.346837] input: PC Speaker as /class/input/input5
[ 60.504139] Floppy drive(s): fd0 is 1.44M
[ 60.521457] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 60.521575] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 60.524072] FDC 0 is a post-1991 82077
[ 61.028170] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
[ 62.031786] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 62.031931] ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
[ 62.032124] ata1.00: hard resetting link
[ 62.351844] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 62.351851] ata1.01: hard resetting link
[ 62.671742] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.671745] ata1.02: hard resetting link
[ 62.991645] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.991647] ata1.03: hard resetting link
[ 63.311554] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 63.311561] ata1.04: hard resetting link
[ 63.631453] ata1.04: SATA link down (SStatus 0 SControl 320)
[ 63.631456] ata1.05: hard resetting link
[ 63.951352] ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 63.951355] ata1.06: hard resetting link
[ 64.272205] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 64.273279] ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 64.273282] ata1.00: 586072368 sectors, multi 16: LBA48
[ 64.273285] ata1.00: applying bridge limits
[ 64.274423] ata1.00: configured for UDMA/100
[ 64.276119] ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 64.276122] ata1.01: 586072368 sectors, multi 0: LBA48
[ 64.276125] ata1.01: applying bridge limits
[ 64.277264] ata1.01: configured for UDMA/100
[ 64.323947] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 64.323950] ata1.02: 586072368 sectors, multi 0: LBA48
[ 64.323952] ata1.02: applying bridge limits
[ 64.382089] ata1.02: configured for UDMA/100
[ 64.426133] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 64.426136] ata1.03: 586072368 sectors, multi 0: LBA48
[ 64.426138] ata1.03: applying bridge limits
[ 64.484410] ata1.03: configured for UDMA/100
[ 64.484478] ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
[ 64.484480] ata1.05: 640 sectors, multi 1: LBA
[ 64.484486] ata1.05: device is on DMA blacklist, disabling DMA
[ 64.484575] ata1.05: configured for PIO4
[ 64.484615] ata1: EH complete
[ 66.562409] ata2: SATA link down (SStatus 0 SControl 0)
[ 68.641778] ata3: SATA link down (SStatus 0 SControl 0)
[ 70.721147] ata4: SATA link down (SStatus 0 SControl 0)
[ 70.721260] scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.721669] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.721680] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.721683] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.721695] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.721740] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.721747] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.721750] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.721761] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.721765] sdb: sdb1
[ 70.728578] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 70.728614] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 70.729063] scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.729336] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.729343] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.729346] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.729357] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.729388] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.729395] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.729398] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.729409] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.729411] sdc: sdc1
[ 70.751335] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 70.751366] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 70.751842] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.751903] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.751911] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.751913] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.751924] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.751953] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.751960] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.751963] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.751974] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.751977] sdd: sdd1
[ 70.767637] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 70.767670] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 70.767716] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.767775] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.767782] sd 1:3:0:0: [sde] Write Protect is off
[ 70.767785] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.767796] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.768539] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.768546] sd 1:3:0:0: [sde] Write Protect is off
[ 70.768549] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.768560] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.768563] sde: sde1
[ 70.785093] sd 1:3:0:0: [sde] Attached SCSI disk
[ 70.785128] sd 1:3:0:0: Attached scsi generic sg5 type 0
[ 70.785174] scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 70.785234] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.785241] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.785244] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.785255] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.785284] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.785291] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.785293] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.785304] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.785307] sdf: unknown partition table
[ 70.786159] sd 1:5:0:0: [sdf] Attached SCSI disk
[ 70.786191] sd 1:5:0:0: Attached scsi generic sg6 type 0
[ 70.786363] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 70.786553] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 70.786744] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
[ 70.786795] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
[ 70.797142] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 70.797280] usb usb1: configuration #1 chosen from 1 choice
[ 70.797308] hub 1-0:1.0: USB hub found
[ 70.797317] hub 1-0:1.0: 8 ports detected
[ 70.901323] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.901336] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 70.901363] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 70.901386] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
[ 70.901506] usb usb2: configuration #1 chosen from 1 choice
[ 70.901531] hub 2-0:1.0: USB hub found
[ 70.901539] hub 2-0:1.0: 2 ports detected
[ 71.005191] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 71.005204] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 71.005229] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 71.005252] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 71.005373] usb usb3: configuration #1 chosen from 1 choice
[ 71.005398] hub 3-0:1.0: USB hub found
[ 71.005405] hub 3-0:1.0: 2 ports detected
[ 71.109172] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.109185] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 71.109211] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 71.109235] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 71.109351] usb usb4: configuration #1 chosen from 1 choice
[ 71.109376] hub 4-0:1.0: USB hub found
[ 71.109383] hub 4-0:1.0: 2 ports detected
[ 71.213117] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.213130] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 71.213155] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 71.213179] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 71.213299] usb usb5: configuration #1 chosen from 1 choice
[ 71.213325] hub 5-0:1.0: USB hub found
[ 71.213332] hub 5-0:1.0: 2 ports detected
[ 71.317585] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 71.319838] Audigy2 value: Special config.
[ 73.765264] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 73.765268] Copyright (c) 1999-2006 Intel Corporation.
[ 73.765309] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 73.765314] PCI: Disallowing DAC for device 0000:00:0e.0
[ 74.025736] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 74.201234] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 74.355702] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 74.355715] ReiserFS: hdb1: using ordered data mode
[ 74.392680] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.394057] ReiserFS: hdb1: checking transaction log (hdb1)
[ 74.489291] ReiserFS: hdb1: Using r5 hash to sort names
[ 74.553988] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 74.553998] ReiserFS: hda2: using ordered data mode
[ 74.558818] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.560151] ReiserFS: hda2: checking transaction log (hda2)
[ 74.623128] ReiserFS: hda2: Using r5 hash to sort names
[ 80.456682] hda: UDMA/100 mode selected
[ 80.460729] hdb: UDMA/133 mode selected
[ 80.515263] hdc: UDMA/33 mode selected
[ 80.532803] hdd: UDMA/33 mode selected
[ 83.053804] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 87.342494] w83627hf: Found W83697HF chip at 0x290
[ 159.125858] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 159.125863] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 159.125866] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 159.125869] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 159.125871] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 159.125874] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 159.125876] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 159.125880] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 159.125883] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 159.125886] ata1: SError: { 10B8B }
[ 159.125890] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125895] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125899] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125904] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125908] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125912] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125917] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125923] ata1.15: hard resetting link
[ 164.216778] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 164.468696] ata1.15: qc timeout (cmd 0xe4)
[ 164.468703] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 164.468706] ata1.15: PMP revalidation failed (errno=-5)
[ 164.468708] ata1.15: retrying hardreset in 5 secs
[ 169.471177] ata1.15: hard resetting link
[ 174.565637] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 174.817555] ata1.15: qc timeout (cmd 0xe4)
[ 174.817562] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 174.817565] ata1.15: PMP revalidation failed (errno=-5)
[ 174.817568] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 174.817570] ata1.15: retrying hardreset in 5 secs
[ 179.820043] ata1.15: hard resetting link
[ 182.019380] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 182.019590] ata1.00: hard resetting link
[ 182.339460] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 182.339463] ata1.01: hard resetting link
[ 182.659362] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.659365] ata1.02: hard resetting link
[ 182.979265] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.979269] ata1.03: hard resetting link
[ 183.299169] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 183.299172] ata1.04: hard resetting link
[ 183.619071] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 183.619074] ata1.05: hard resetting link
[ 183.938971] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 183.938975] ata1.06: hard resetting link
[ 184.258874] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 184.261106] ata1.00: configured for UDMA/100
[ 184.263303] ata1.01: configured for UDMA/100
[ 184.263398] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 184.263401] ata1.02: revalidation failed (errno=-5)
[ 184.263406] ata1.15: hard resetting link
[ 186.462034] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 186.462308] ata1.00: hard resetting link
[ 186.782113] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 186.782117] ata1.01: hard resetting link
[ 187.102015] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.102018] ata1.02: hard resetting link
[ 187.421918] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.421922] ata1.03: hard resetting link
[ 187.741820] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.741823] ata1.04: hard resetting link
[ 188.061723] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 188.061727] ata1.05: hard resetting link
[ 188.381625] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 188.381628] ata1.06: hard resetting link
[ 188.701528] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 188.703706] ata1.00: configured for UDMA/100
[ 188.705935] ata1.01: configured for UDMA/100
[ 188.811817] ata1.02: configured for UDMA/100
[ 188.915919] ata1.03: configured for UDMA/100
[ 188.916051] ata1.05: device is on DMA blacklist, disabling DMA
[ 188.916182] ata1.05: configured for PIO4
[ 188.916453] ata1: EH complete
[ 188.916481] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916492] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916496] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916508] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916524] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916532] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916535] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916546] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916560] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916567] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916570] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916581] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916595] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916602] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916605] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916616] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916629] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916637] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916640] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916651] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916664] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916671] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916674] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916686] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916698] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916705] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916708] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916720] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916732] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916739] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916742] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916753] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916766] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916773] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916776] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916787] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916799] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916807] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916810] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916821] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 233.874452] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 233.874458] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 233.874462] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 233.874465] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 233.874468] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 233.874471] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 233.874474] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 233.874478] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 233.874482] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 233.874486] ata1: SError: { 10B8B }
[ 233.874490] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874495] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874501] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874506] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874511] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874516] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874521] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874529] ata1.15: hard resetting link
[ 238.966100] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 239.218017] ata1.15: qc timeout (cmd 0xe4)
[ 239.218026] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 239.218029] ata1.15: PMP revalidation failed (errno=-5)
[ 239.218032] ata1.15: retrying hardreset in 5 secs
[ 244.220499] ata1.15: hard resetting link
[ 249.314958] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 249.566876] ata1.15: qc timeout (cmd 0xe4)
[ 249.566883] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 249.566886] ata1.15: PMP revalidation failed (errno=-5)
[ 249.566890] ata1.15: retrying hardreset in 5 secs
[ 254.569359] ata1.15: hard resetting link
[ 256.768701] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 256.768897] ata1.00: hard resetting link
[ 257.088783] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 257.088787] ata1.01: hard resetting link
[ 257.408684] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.408688] ata1.02: hard resetting link
[ 257.728587] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.728591] ata1.03: hard resetting link
[ 258.048491] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 258.048495] ata1.04: hard resetting link
[ 258.368394] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 258.368397] ata1.05: hard resetting link
[ 258.688294] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 258.688298] ata1.06: hard resetting link
[ 259.008199] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 259.008295] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 259.008299] ata1.00: revalidation failed (errno=-5)
[ 259.008304] ata1.15: hard resetting link
[ 261.207356] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 261.207634] ata1.00: hard resetting link
[ 261.527434] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 261.527439] ata1.01: hard resetting link
[ 261.847337] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 261.847340] ata1.02: hard resetting link
[ 262.167238] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.167242] ata1.03: hard resetting link
[ 262.487142] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.487146] ata1.04: hard resetting link
[ 262.807046] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 262.807050] ata1.05: hard resetting link
[ 263.126946] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 263.126950] ata1.06: hard resetting link
[ 263.446852] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 263.449093] ata1.00: configured for UDMA/100
[ 263.451311] ata1.01: configured for UDMA/100
[ 263.556976] ata1.02: configured for UDMA/100
[ 263.658661] ata1.03: configured for UDMA/100
[ 263.658793] ata1.05: device is on DMA blacklist, disabling DMA
[ 263.658923] ata1.05: configured for PIO4
[ 263.659192] ata1: EH complete
[ 263.659218] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659229] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659232] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659245] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659260] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659267] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659270] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659281] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659295] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659303] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659305] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659317] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659330] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659337] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659340] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659351] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659365] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659372] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659375] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659386] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659399] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659407] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659409] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659421] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659433] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659440] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659443] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659454] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659467] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659474] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659477] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659488] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659500] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659508] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659511] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659522] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659534] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659541] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659544] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659555] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[-- Attachment #4: 3_PlugUnplug.log --]
[-- Type: text/plain, Size: 31316 bytes --]
128@0xfd900000 port 0xfd800000 irq 17
[ 59.832477] ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
[ 59.832480] ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
[ 59.832484] ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
[ 60.346837] input: PC Speaker as /class/input/input5
[ 60.504139] Floppy drive(s): fd0 is 1.44M
[ 60.521457] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 60.521575] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 60.524072] FDC 0 is a post-1991 82077
[ 61.028170] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000059341e]
[ 62.031786] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 62.031931] ata1.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9
[ 62.032124] ata1.00: hard resetting link
[ 62.351844] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 62.351851] ata1.01: hard resetting link
[ 62.671742] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.671745] ata1.02: hard resetting link
[ 62.991645] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 62.991647] ata1.03: hard resetting link
[ 63.311554] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 63.311561] ata1.04: hard resetting link
[ 63.631453] ata1.04: SATA link down (SStatus 0 SControl 320)
[ 63.631456] ata1.05: hard resetting link
[ 63.951352] ata1.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 63.951355] ata1.06: hard resetting link
[ 64.272205] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
[ 64.273279] ata1.00: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 64.273282] ata1.00: 586072368 sectors, multi 16: LBA48
[ 64.273285] ata1.00: applying bridge limits
[ 64.274423] ata1.00: configured for UDMA/100
[ 64.276119] ata1.01: ATA-7: ST3300831A, 3.03, max UDMA/100
[ 64.276122] ata1.01: 586072368 sectors, multi 0: LBA48
[ 64.276125] ata1.01: applying bridge limits
[ 64.277264] ata1.01: configured for UDMA/100
[ 64.323947] ata1.02: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 64.323950] ata1.02: 586072368 sectors, multi 0: LBA48
[ 64.323952] ata1.02: applying bridge limits
[ 64.382089] ata1.02: configured for UDMA/100
[ 64.426133] ata1.03: ATA-7: ST3300622A, 3.AND, max UDMA/100
[ 64.426136] ata1.03: 586072368 sectors, multi 0: LBA48
[ 64.426138] ata1.03: applying bridge limits
[ 64.484410] ata1.03: configured for UDMA/100
[ 64.484478] ata1.05: ATA-6: Config Disk, PLS12061, max UDMA/133
[ 64.484480] ata1.05: 640 sectors, multi 1: LBA
[ 64.484486] ata1.05: device is on DMA blacklist, disabling DMA
[ 64.484575] ata1.05: configured for PIO4
[ 64.484615] ata1: EH complete
[ 66.562409] ata2: SATA link down (SStatus 0 SControl 0)
[ 68.641778] ata3: SATA link down (SStatus 0 SControl 0)
[ 70.721147] ata4: SATA link down (SStatus 0 SControl 0)
[ 70.721260] scsi 1:0:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.721669] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.721680] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.721683] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.721695] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.721740] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 70.721747] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.721750] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 70.721761] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.721765] sdb: sdb1
[ 70.728578] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 70.728614] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 70.729063] scsi 1:1:0:0: Direct-Access ATA ST3300831A 3.03 PQ: 0 ANSI: 5
[ 70.729336] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.729343] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.729346] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.729357] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.729388] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 70.729395] sd 1:1:0:0: [sdc] Write Protect is off
[ 70.729398] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 70.729409] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.729411] sdc: sdc1
[ 70.751335] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 70.751366] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 70.751842] scsi 1:2:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.751903] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.751911] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.751913] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.751924] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.751953] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 70.751960] sd 1:2:0:0: [sdd] Write Protect is off
[ 70.751963] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.751974] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.751977] sdd: sdd1
[ 70.767637] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 70.767670] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 70.767716] scsi 1:3:0:0: Direct-Access ATA ST3300622A 3.AN PQ: 0 ANSI: 5
[ 70.767775] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.767782] sd 1:3:0:0: [sde] Write Protect is off
[ 70.767785] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.767796] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.768539] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 70.768546] sd 1:3:0:0: [sde] Write Protect is off
[ 70.768549] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 70.768560] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.768563] sde: sde1
[ 70.785093] sd 1:3:0:0: [sde] Attached SCSI disk
[ 70.785128] sd 1:3:0:0: Attached scsi generic sg5 type 0
[ 70.785174] scsi 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 70.785234] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.785241] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.785244] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.785255] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.785284] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.785291] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.785293] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.785304] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.785307] sdf: unknown partition table
[ 70.786159] sd 1:5:0:0: [sdf] Attached SCSI disk
[ 70.786191] sd 1:5:0:0: Attached scsi generic sg6 type 0
[ 70.786363] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 70.786553] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 70.786744] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
[ 70.786795] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
[ 70.797142] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 70.797280] usb usb1: configuration #1 chosen from 1 choice
[ 70.797308] hub 1-0:1.0: USB hub found
[ 70.797317] hub 1-0:1.0: 8 ports detected
[ 70.901323] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.901336] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 70.901363] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 70.901386] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
[ 70.901506] usb usb2: configuration #1 chosen from 1 choice
[ 70.901531] hub 2-0:1.0: USB hub found
[ 70.901539] hub 2-0:1.0: 2 ports detected
[ 71.005191] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 71.005204] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 71.005229] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 71.005252] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 71.005373] usb usb3: configuration #1 chosen from 1 choice
[ 71.005398] hub 3-0:1.0: USB hub found
[ 71.005405] hub 3-0:1.0: 2 ports detected
[ 71.109172] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.109185] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 71.109211] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 71.109235] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 71.109351] usb usb4: configuration #1 chosen from 1 choice
[ 71.109376] hub 4-0:1.0: USB hub found
[ 71.109383] hub 4-0:1.0: 2 ports detected
[ 71.213117] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.213130] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 71.213155] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 71.213179] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 71.213299] usb usb5: configuration #1 chosen from 1 choice
[ 71.213325] hub 5-0:1.0: USB hub found
[ 71.213332] hub 5-0:1.0: 2 ports detected
[ 71.317585] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 71.319838] Audigy2 value: Special config.
[ 73.765264] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 73.765268] Copyright (c) 1999-2006 Intel Corporation.
[ 73.765309] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 73.765314] PCI: Disallowing DAC for device 0000:00:0e.0
[ 74.025736] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 74.201234] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 74.355702] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 74.355715] ReiserFS: hdb1: using ordered data mode
[ 74.392680] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.394057] ReiserFS: hdb1: checking transaction log (hdb1)
[ 74.489291] ReiserFS: hdb1: Using r5 hash to sort names
[ 74.553988] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 74.553998] ReiserFS: hda2: using ordered data mode
[ 74.558818] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.560151] ReiserFS: hda2: checking transaction log (hda2)
[ 74.623128] ReiserFS: hda2: Using r5 hash to sort names
[ 80.456682] hda: UDMA/100 mode selected
[ 80.460729] hdb: UDMA/133 mode selected
[ 80.515263] hdc: UDMA/33 mode selected
[ 80.532803] hdd: UDMA/33 mode selected
[ 83.053804] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 87.342494] w83627hf: Found W83697HF chip at 0x290
[ 159.125858] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 159.125863] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 159.125866] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 159.125869] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 159.125871] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 159.125874] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 159.125876] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 159.125880] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 159.125883] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 159.125886] ata1: SError: { 10B8B }
[ 159.125890] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125895] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125899] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125904] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125908] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125912] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125917] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125923] ata1.15: hard resetting link
[ 164.216778] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 164.468696] ata1.15: qc timeout (cmd 0xe4)
[ 164.468703] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 164.468706] ata1.15: PMP revalidation failed (errno=-5)
[ 164.468708] ata1.15: retrying hardreset in 5 secs
[ 169.471177] ata1.15: hard resetting link
[ 174.565637] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 174.817555] ata1.15: qc timeout (cmd 0xe4)
[ 174.817562] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 174.817565] ata1.15: PMP revalidation failed (errno=-5)
[ 174.817568] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 174.817570] ata1.15: retrying hardreset in 5 secs
[ 179.820043] ata1.15: hard resetting link
[ 182.019380] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 182.019590] ata1.00: hard resetting link
[ 182.339460] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 182.339463] ata1.01: hard resetting link
[ 182.659362] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.659365] ata1.02: hard resetting link
[ 182.979265] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.979269] ata1.03: hard resetting link
[ 183.299169] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 183.299172] ata1.04: hard resetting link
[ 183.619071] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 183.619074] ata1.05: hard resetting link
[ 183.938971] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 183.938975] ata1.06: hard resetting link
[ 184.258874] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 184.261106] ata1.00: configured for UDMA/100
[ 184.263303] ata1.01: configured for UDMA/100
[ 184.263398] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 184.263401] ata1.02: revalidation failed (errno=-5)
[ 184.263406] ata1.15: hard resetting link
[ 186.462034] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 186.462308] ata1.00: hard resetting link
[ 186.782113] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 186.782117] ata1.01: hard resetting link
[ 187.102015] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.102018] ata1.02: hard resetting link
[ 187.421918] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.421922] ata1.03: hard resetting link
[ 187.741820] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.741823] ata1.04: hard resetting link
[ 188.061723] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 188.061727] ata1.05: hard resetting link
[ 188.381625] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 188.381628] ata1.06: hard resetting link
[ 188.701528] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 188.703706] ata1.00: configured for UDMA/100
[ 188.705935] ata1.01: configured for UDMA/100
[ 188.811817] ata1.02: configured for UDMA/100
[ 188.915919] ata1.03: configured for UDMA/100
[ 188.916051] ata1.05: device is on DMA blacklist, disabling DMA
[ 188.916182] ata1.05: configured for PIO4
[ 188.916453] ata1: EH complete
[ 188.916481] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916492] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916496] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916508] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916524] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916532] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916535] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916546] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916560] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916567] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916570] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916581] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916595] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916602] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916605] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916616] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916629] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916637] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916640] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916651] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916664] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916671] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916674] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916686] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916698] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916705] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916708] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916720] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916732] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916739] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916742] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916753] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916766] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916773] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916776] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916787] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916799] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916807] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916810] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916821] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 233.874452] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 233.874458] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 233.874462] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 233.874465] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 233.874468] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 233.874471] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 233.874474] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 233.874478] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 233.874482] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 233.874486] ata1: SError: { 10B8B }
[ 233.874490] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874495] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874501] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874506] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874511] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874516] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874521] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874529] ata1.15: hard resetting link
[ 238.966100] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 239.218017] ata1.15: qc timeout (cmd 0xe4)
[ 239.218026] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 239.218029] ata1.15: PMP revalidation failed (errno=-5)
[ 239.218032] ata1.15: retrying hardreset in 5 secs
[ 244.220499] ata1.15: hard resetting link
[ 249.314958] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 249.566876] ata1.15: qc timeout (cmd 0xe4)
[ 249.566883] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 249.566886] ata1.15: PMP revalidation failed (errno=-5)
[ 249.566890] ata1.15: retrying hardreset in 5 secs
[ 254.569359] ata1.15: hard resetting link
[ 256.768701] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 256.768897] ata1.00: hard resetting link
[ 257.088783] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 257.088787] ata1.01: hard resetting link
[ 257.408684] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.408688] ata1.02: hard resetting link
[ 257.728587] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.728591] ata1.03: hard resetting link
[ 258.048491] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 258.048495] ata1.04: hard resetting link
[ 258.368394] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 258.368397] ata1.05: hard resetting link
[ 258.688294] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 258.688298] ata1.06: hard resetting link
[ 259.008199] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 259.008295] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 259.008299] ata1.00: revalidation failed (errno=-5)
[ 259.008304] ata1.15: hard resetting link
[ 261.207356] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 261.207634] ata1.00: hard resetting link
[ 261.527434] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 261.527439] ata1.01: hard resetting link
[ 261.847337] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 261.847340] ata1.02: hard resetting link
[ 262.167238] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.167242] ata1.03: hard resetting link
[ 262.487142] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.487146] ata1.04: hard resetting link
[ 262.807046] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 262.807050] ata1.05: hard resetting link
[ 263.126946] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 263.126950] ata1.06: hard resetting link
[ 263.446852] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 263.449093] ata1.00: configured for UDMA/100
[ 263.451311] ata1.01: configured for UDMA/100
[ 263.556976] ata1.02: configured for UDMA/100
[ 263.658661] ata1.03: configured for UDMA/100
[ 263.658793] ata1.05: device is on DMA blacklist, disabling DMA
[ 263.658923] ata1.05: configured for PIO4
[ 263.659192] ata1: EH complete
[ 263.659218] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659229] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659232] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659245] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659260] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659267] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659270] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659281] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659295] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659303] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659305] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659317] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659330] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659337] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659340] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659351] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659365] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659372] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659375] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659386] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659399] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659407] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659409] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659421] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659433] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659440] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659443] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659454] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659467] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659474] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659477] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659488] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659500] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659508] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659511] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659522] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659534] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659541] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659544] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659555] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 337.619074] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 337.619079] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 337.619083] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 337.619086] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 337.619089] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 337.619092] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 337.619095] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 337.619099] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 337.619103] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 337.619107] ata1: SError: { 10B8B }
[ 337.619111] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619116] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619122] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619127] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619132] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619137] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619142] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619150] ata1.15: hard resetting link
[ 339.695540] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 339.947457] ata1.15: qc timeout (cmd 0xe4)
[ 339.947465] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 339.947469] ata1.15: PMP revalidation failed (errno=-5)
[ 339.947472] ata1.15: retrying hardreset in 5 secs
[ 344.949939] ata1.15: hard resetting link
[ 347.029314] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 347.281232] ata1.15: qc timeout (cmd 0xe4)
[ 347.281239] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 347.281242] ata1.15: PMP revalidation failed (errno=-5)
[ 347.281246] ata1.15: retrying hardreset in 5 secs
[ 352.283714] ata1.15: hard resetting link
[ 356.250521] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 356.250717] ata1.00: hard resetting link
[ 356.570601] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 356.570605] ata1.01: hard resetting link
[ 356.890503] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 356.890507] ata1.02: hard resetting link
[ 357.210406] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.210411] ata1.03: hard resetting link
[ 357.530309] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.530313] ata1.04: hard resetting link
[ 357.850212] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 357.850216] ata1.05: hard resetting link
[ 358.170112] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 358.170116] ata1.06: hard resetting link
[ 358.490020] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 358.492276] ata1.00: configured for UDMA/100
[ 358.494506] ata1.01: configured for UDMA/100
[ 358.595946] ata1.02: configured for UDMA/100
[ 358.705215] ata1.03: configured for UDMA/100
[ 358.705316] ata1.05: device is on DMA blacklist, disabling DMA
[ 358.705472] ata1.05: configured for PIO4
[ 358.705734] ata1: EH complete
[ 358.705759] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705773] sd 1:0:0:0: [sdb] Write Protect is off
[ 358.705776] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 358.705789] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705804] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705812] sd 1:1:0:0: [sdc] Write Protect is off
[ 358.705815] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 358.705827] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705841] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705849] sd 1:2:0:0: [sdd] Write Protect is off
[ 358.705852] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 358.705863] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705877] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705885] sd 1:3:0:0: [sde] Write Protect is off
[ 358.705888] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 358.705900] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705913] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 358.705921] sd 1:5:0:0: [sdf] Write Protect is off
[ 358.705924] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 358.705936] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705949] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705957] sd 1:0:0:0: [sdb] Write Protect is off
[ 358.705960] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 358.705972] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705985] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705992] sd 1:1:0:0: [sdc] Write Protect is off
[ 358.705995] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 358.706007] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706020] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 358.706028] sd 1:2:0:0: [sdd] Write Protect is off
[ 358.706030] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 358.706042] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706055] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 358.706063] sd 1:3:0:0: [sde] Write Protect is off
[ 358.706066] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 358.706077] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706090] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 358.706098] sd 1:5:0:0: [sdf] Write Protect is off
[ 358.706101] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 358.706112] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[-- Attachment #5: 4_PowerOnOffTwice.log --]
[-- Type: text/plain, Size: 31268 bytes --]
i 1:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5
[ 70.785234] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.785241] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.785244] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.785255] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.785284] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 70.785291] sd 1:5:0:0: [sdf] Write Protect is off
[ 70.785293] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 70.785304] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 70.785307] sdf: unknown partition table
[ 70.786159] sd 1:5:0:0: [sdf] Attached SCSI disk
[ 70.786191] sd 1:5:0:0: Attached scsi generic sg6 type 0
[ 70.786363] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 70.786553] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 70.786744] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
[ 70.786795] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
[ 70.797142] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 70.797280] usb usb1: configuration #1 chosen from 1 choice
[ 70.797308] hub 1-0:1.0: USB hub found
[ 70.797317] hub 1-0:1.0: 8 ports detected
[ 70.901323] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.901336] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 70.901363] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 70.901386] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
[ 70.901506] usb usb2: configuration #1 chosen from 1 choice
[ 70.901531] hub 2-0:1.0: USB hub found
[ 70.901539] hub 2-0:1.0: 2 ports detected
[ 71.005191] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 71.005204] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 71.005229] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 71.005252] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 71.005373] usb usb3: configuration #1 chosen from 1 choice
[ 71.005398] hub 3-0:1.0: USB hub found
[ 71.005405] hub 3-0:1.0: 2 ports detected
[ 71.109172] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.109185] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 71.109211] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 71.109235] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 71.109351] usb usb4: configuration #1 chosen from 1 choice
[ 71.109376] hub 4-0:1.0: USB hub found
[ 71.109383] hub 4-0:1.0: 2 ports detected
[ 71.213117] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.213130] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 71.213155] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 71.213179] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 71.213299] usb usb5: configuration #1 chosen from 1 choice
[ 71.213325] hub 5-0:1.0: USB hub found
[ 71.213332] hub 5-0:1.0: 2 ports detected
[ 71.317585] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 71.319838] Audigy2 value: Special config.
[ 73.765264] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 73.765268] Copyright (c) 1999-2006 Intel Corporation.
[ 73.765309] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 73.765314] PCI: Disallowing DAC for device 0000:00:0e.0
[ 74.025736] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 74.201234] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 74.355702] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 74.355715] ReiserFS: hdb1: using ordered data mode
[ 74.392680] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.394057] ReiserFS: hdb1: checking transaction log (hdb1)
[ 74.489291] ReiserFS: hdb1: Using r5 hash to sort names
[ 74.553988] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 74.553998] ReiserFS: hda2: using ordered data mode
[ 74.558818] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.560151] ReiserFS: hda2: checking transaction log (hda2)
[ 74.623128] ReiserFS: hda2: Using r5 hash to sort names
[ 80.456682] hda: UDMA/100 mode selected
[ 80.460729] hdb: UDMA/133 mode selected
[ 80.515263] hdc: UDMA/33 mode selected
[ 80.532803] hdd: UDMA/33 mode selected
[ 83.053804] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 87.342494] w83627hf: Found W83697HF chip at 0x290
[ 159.125858] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 159.125863] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 159.125866] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 159.125869] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 159.125871] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 159.125874] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 159.125876] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 159.125880] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 159.125883] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 159.125886] ata1: SError: { 10B8B }
[ 159.125890] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125895] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125899] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125904] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125908] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125912] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125917] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125923] ata1.15: hard resetting link
[ 164.216778] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 164.468696] ata1.15: qc timeout (cmd 0xe4)
[ 164.468703] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 164.468706] ata1.15: PMP revalidation failed (errno=-5)
[ 164.468708] ata1.15: retrying hardreset in 5 secs
[ 169.471177] ata1.15: hard resetting link
[ 174.565637] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 174.817555] ata1.15: qc timeout (cmd 0xe4)
[ 174.817562] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 174.817565] ata1.15: PMP revalidation failed (errno=-5)
[ 174.817568] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 174.817570] ata1.15: retrying hardreset in 5 secs
[ 179.820043] ata1.15: hard resetting link
[ 182.019380] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 182.019590] ata1.00: hard resetting link
[ 182.339460] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 182.339463] ata1.01: hard resetting link
[ 182.659362] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.659365] ata1.02: hard resetting link
[ 182.979265] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.979269] ata1.03: hard resetting link
[ 183.299169] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 183.299172] ata1.04: hard resetting link
[ 183.619071] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 183.619074] ata1.05: hard resetting link
[ 183.938971] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 183.938975] ata1.06: hard resetting link
[ 184.258874] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 184.261106] ata1.00: configured for UDMA/100
[ 184.263303] ata1.01: configured for UDMA/100
[ 184.263398] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 184.263401] ata1.02: revalidation failed (errno=-5)
[ 184.263406] ata1.15: hard resetting link
[ 186.462034] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 186.462308] ata1.00: hard resetting link
[ 186.782113] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 186.782117] ata1.01: hard resetting link
[ 187.102015] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.102018] ata1.02: hard resetting link
[ 187.421918] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.421922] ata1.03: hard resetting link
[ 187.741820] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.741823] ata1.04: hard resetting link
[ 188.061723] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 188.061727] ata1.05: hard resetting link
[ 188.381625] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 188.381628] ata1.06: hard resetting link
[ 188.701528] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 188.703706] ata1.00: configured for UDMA/100
[ 188.705935] ata1.01: configured for UDMA/100
[ 188.811817] ata1.02: configured for UDMA/100
[ 188.915919] ata1.03: configured for UDMA/100
[ 188.916051] ata1.05: device is on DMA blacklist, disabling DMA
[ 188.916182] ata1.05: configured for PIO4
[ 188.916453] ata1: EH complete
[ 188.916481] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916492] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916496] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916508] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916524] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916532] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916535] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916546] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916560] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916567] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916570] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916581] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916595] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916602] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916605] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916616] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916629] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916637] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916640] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916651] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916664] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916671] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916674] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916686] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916698] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916705] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916708] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916720] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916732] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916739] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916742] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916753] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916766] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916773] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916776] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916787] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916799] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916807] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916810] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916821] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 233.874452] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 233.874458] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 233.874462] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 233.874465] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 233.874468] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 233.874471] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 233.874474] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 233.874478] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 233.874482] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 233.874486] ata1: SError: { 10B8B }
[ 233.874490] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874495] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874501] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874506] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874511] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874516] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874521] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874529] ata1.15: hard resetting link
[ 238.966100] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 239.218017] ata1.15: qc timeout (cmd 0xe4)
[ 239.218026] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 239.218029] ata1.15: PMP revalidation failed (errno=-5)
[ 239.218032] ata1.15: retrying hardreset in 5 secs
[ 244.220499] ata1.15: hard resetting link
[ 249.314958] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 249.566876] ata1.15: qc timeout (cmd 0xe4)
[ 249.566883] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 249.566886] ata1.15: PMP revalidation failed (errno=-5)
[ 249.566890] ata1.15: retrying hardreset in 5 secs
[ 254.569359] ata1.15: hard resetting link
[ 256.768701] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 256.768897] ata1.00: hard resetting link
[ 257.088783] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 257.088787] ata1.01: hard resetting link
[ 257.408684] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.408688] ata1.02: hard resetting link
[ 257.728587] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.728591] ata1.03: hard resetting link
[ 258.048491] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 258.048495] ata1.04: hard resetting link
[ 258.368394] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 258.368397] ata1.05: hard resetting link
[ 258.688294] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 258.688298] ata1.06: hard resetting link
[ 259.008199] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 259.008295] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 259.008299] ata1.00: revalidation failed (errno=-5)
[ 259.008304] ata1.15: hard resetting link
[ 261.207356] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 261.207634] ata1.00: hard resetting link
[ 261.527434] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 261.527439] ata1.01: hard resetting link
[ 261.847337] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 261.847340] ata1.02: hard resetting link
[ 262.167238] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.167242] ata1.03: hard resetting link
[ 262.487142] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.487146] ata1.04: hard resetting link
[ 262.807046] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 262.807050] ata1.05: hard resetting link
[ 263.126946] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 263.126950] ata1.06: hard resetting link
[ 263.446852] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 263.449093] ata1.00: configured for UDMA/100
[ 263.451311] ata1.01: configured for UDMA/100
[ 263.556976] ata1.02: configured for UDMA/100
[ 263.658661] ata1.03: configured for UDMA/100
[ 263.658793] ata1.05: device is on DMA blacklist, disabling DMA
[ 263.658923] ata1.05: configured for PIO4
[ 263.659192] ata1: EH complete
[ 263.659218] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659229] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659232] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659245] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659260] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659267] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659270] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659281] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659295] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659303] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659305] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659317] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659330] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659337] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659340] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659351] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659365] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659372] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659375] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659386] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659399] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659407] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659409] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659421] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659433] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659440] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659443] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659454] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659467] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659474] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659477] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659488] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659500] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659508] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659511] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659522] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659534] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659541] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659544] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659555] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 337.619074] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 337.619079] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 337.619083] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 337.619086] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 337.619089] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 337.619092] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 337.619095] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 337.619099] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 337.619103] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 337.619107] ata1: SError: { 10B8B }
[ 337.619111] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619116] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619122] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619127] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619132] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619137] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619142] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619150] ata1.15: hard resetting link
[ 339.695540] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 339.947457] ata1.15: qc timeout (cmd 0xe4)
[ 339.947465] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 339.947469] ata1.15: PMP revalidation failed (errno=-5)
[ 339.947472] ata1.15: retrying hardreset in 5 secs
[ 344.949939] ata1.15: hard resetting link
[ 347.029314] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 347.281232] ata1.15: qc timeout (cmd 0xe4)
[ 347.281239] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 347.281242] ata1.15: PMP revalidation failed (errno=-5)
[ 347.281246] ata1.15: retrying hardreset in 5 secs
[ 352.283714] ata1.15: hard resetting link
[ 356.250521] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 356.250717] ata1.00: hard resetting link
[ 356.570601] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 356.570605] ata1.01: hard resetting link
[ 356.890503] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 356.890507] ata1.02: hard resetting link
[ 357.210406] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.210411] ata1.03: hard resetting link
[ 357.530309] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.530313] ata1.04: hard resetting link
[ 357.850212] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 357.850216] ata1.05: hard resetting link
[ 358.170112] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 358.170116] ata1.06: hard resetting link
[ 358.490020] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 358.492276] ata1.00: configured for UDMA/100
[ 358.494506] ata1.01: configured for UDMA/100
[ 358.595946] ata1.02: configured for UDMA/100
[ 358.705215] ata1.03: configured for UDMA/100
[ 358.705316] ata1.05: device is on DMA blacklist, disabling DMA
[ 358.705472] ata1.05: configured for PIO4
[ 358.705734] ata1: EH complete
[ 358.705759] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705773] sd 1:0:0:0: [sdb] Write Protect is off
[ 358.705776] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 358.705789] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705804] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705812] sd 1:1:0:0: [sdc] Write Protect is off
[ 358.705815] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 358.705827] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705841] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705849] sd 1:2:0:0: [sdd] Write Protect is off
[ 358.705852] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 358.705863] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705877] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705885] sd 1:3:0:0: [sde] Write Protect is off
[ 358.705888] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 358.705900] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705913] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 358.705921] sd 1:5:0:0: [sdf] Write Protect is off
[ 358.705924] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 358.705936] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705949] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705957] sd 1:0:0:0: [sdb] Write Protect is off
[ 358.705960] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 358.705972] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705985] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705992] sd 1:1:0:0: [sdc] Write Protect is off
[ 358.705995] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 358.706007] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706020] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 358.706028] sd 1:2:0:0: [sdd] Write Protect is off
[ 358.706030] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 358.706042] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706055] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 358.706063] sd 1:3:0:0: [sde] Write Protect is off
[ 358.706066] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 358.706077] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706090] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 358.706098] sd 1:5:0:0: [sdf] Write Protect is off
[ 358.706101] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 358.706112] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 404.739637] ata1.15: limiting speed to UDMA7:PIO5
[ 404.739644] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 404.739648] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 404.739651] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 404.739654] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 404.739657] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 404.739660] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 404.739663] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 404.739667] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 404.739671] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 404.739675] ata1: SError: { 10B8B }
[ 404.739679] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739685] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739690] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739695] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739700] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739705] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739710] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739718] ata1.15: hard resetting link
[ 409.830262] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 410.082180] ata1.15: qc timeout (cmd 0xe4)
[ 410.082188] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 410.082191] ata1.15: PMP revalidation failed (errno=-5)
[ 410.082194] ata1.15: retrying hardreset in 5 secs
[ 415.084662] ata1.15: hard resetting link
[ 420.179121] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 420.431039] ata1.15: qc timeout (cmd 0xe4)
[ 420.431047] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 420.431050] ata1.15: PMP revalidation failed (errno=-5)
[ 420.431054] ata1.15: retrying hardreset in 5 secs
[ 425.433523] ata1.15: hard resetting link
[ 435.438490] ata1.15: softreset failed (timeout)
[ 435.438494] ata1.15: hard resetting link
[ 445.443457] ata1.15: softreset failed (timeout)
[ 445.443463] ata1.15: hard resetting link
[ 480.432842] ata1.15: softreset failed (timeout)
[ 480.432850] ata1.15: hard resetting link
[ 485.431325] ata1.15: softreset failed (timeout)
[ 485.431329] ata1.15: failed to reset PMP, giving up
[ 485.431332] ata1.15: Port Multiplier detaching
[ 485.431340] ata1.00: disabled
[ 485.431343] ata1.01: disabled
[ 485.431346] ata1.02: disabled
[ 485.431348] ata1.03: disabled
[ 485.431350] ata1.05: disabled
[ 485.431354] ata1.00: disabled
[ 485.431360] ata1: hard resetting link
[ 495.436287] ata1: softreset failed (timeout)
[ 495.436290] ata1: hard resetting link
[ 505.441252] ata1: softreset failed (timeout)
[ 505.441255] ata1: hard resetting link
[ 540.430639] ata1: softreset failed (timeout)
[ 540.430647] ata1: limiting SATA link speed to 1.5 Gbps
[ 540.430650] ata1: hard resetting link
[ 545.525097] ata1: SATA link down (SStatus 1 SControl 10)
[ 545.525115] ata1: EH complete
[ 545.525125] ata1.00: detaching (SCSI 1:0:0:0)
[ 545.525299] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 545.525613] sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525617] sd 1:0:0:0: [sdb] Stopping disk
[ 545.525623] sd 1:0:0:0: [sdb] START_STOP FAILED
[ 545.525626] sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525663] ata1.01: detaching (SCSI 1:1:0:0)
[ 545.525799] sd 1:1:0:0: [sdc] Synchronizing SCSI cache
[ 545.525944] sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525948] sd 1:1:0:0: [sdc] Stopping disk
[ 545.525970] sd 1:1:0:0: [sdc] START_STOP FAILED
[ 545.525972] sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
[ 545.526000] ata1.02: detaching (SCSI 1:2:0:0)
[ 545.526146] sd 1:2:0:0: [sdd] Synchronizing SCSI cache
[ 545.527048] sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527053] sd 1:2:0:0: [sdd] Stopping disk
[ 545.527071] sd 1:2:0:0: [sdd] START_STOP FAILED
[ 545.527074] sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527106] ata1.03: detaching (SCSI 1:3:0:0)
[ 545.527246] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 545.527287] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527290] sd 1:3:0:0: [sde] Stopping disk
[ 545.527304] sd 1:3:0:0: [sde] START_STOP FAILED
[ 545.527306] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527333] ata1.05: detaching (SCSI 1:5:0:0)
[ 545.527451] sd 1:5:0:0: [sdf] Stopping disk
[ 545.527459] sd 1:5:0:0: [sdf] START_STOP FAILED
[ 545.527462] sd 1:5:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
[ 559.279656] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xa frozen
[ 559.279662] ata1: irq_stat 0x00a40080, device exchanged
[ 559.279673] ata1: hard resetting link
[ 563.427669] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 563.679583] ata1.15: qc timeout (cmd 0xe4)
[ 563.679589] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 563.679593] ata1: failed to recover some devices, retrying in 5 secs
[ 568.682071] ata1: hard resetting link
[ 578.687033] ata1: softreset failed (timeout)
[ 578.687039] ata1: hard resetting link
[ 588.691996] ata1: softreset failed (timeout)
[ 588.691999] ata1: hard resetting link
[ 623.681382] ata1: softreset failed (timeout)
[ 623.681390] ata1: limiting SATA link speed to 1.5 Gbps
[ 623.681393] ata1: hard resetting link
[ 628.679864] ata1: softreset failed (timeout)
[ 628.679867] ata1: reset failed, giving up
[ 628.679878] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xa frozen t4
[ 628.679883] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 628.679892] ata1: hard resetting link
[ 638.684830] ata1: softreset failed (timeout)
[ 638.684836] ata1: hard resetting link
[ 648.689795] ata1: softreset failed (timeout)
[ 648.689801] ata1: hard resetting link
[ 683.679179] ata1: softreset failed (timeout)
[ 683.679186] ata1: limiting SATA link speed to 1.5 Gbps
[ 683.679189] ata1: hard resetting link
[ 688.677661] ata1: softreset failed (timeout)
[ 688.677664] ata1: reset failed, giving up
[ 688.677670] ata1: EH complete
[-- Attachment #6: 5_Broken.log --]
[-- Type: text/plain, Size: 31256 bytes --]
sd 1:5:0:0: Attached scsi generic sg6 type 0
[ 70.786363] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 70.786553] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 70.786744] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
[ 70.786795] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdf00000
[ 70.797142] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 70.797280] usb usb1: configuration #1 chosen from 1 choice
[ 70.797308] hub 1-0:1.0: USB hub found
[ 70.797317] hub 1-0:1.0: 8 ports detected
[ 70.901323] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 70.901336] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 70.901363] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 70.901386] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b800
[ 70.901506] usb usb2: configuration #1 chosen from 1 choice
[ 70.901531] hub 2-0:1.0: USB hub found
[ 70.901539] hub 2-0:1.0: 2 ports detected
[ 71.005191] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 71.005204] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 71.005229] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 71.005252] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 71.005373] usb usb3: configuration #1 chosen from 1 choice
[ 71.005398] hub 3-0:1.0: USB hub found
[ 71.005405] hub 3-0:1.0: 2 ports detected
[ 71.109172] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.109185] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 71.109211] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 71.109235] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 71.109351] usb usb4: configuration #1 chosen from 1 choice
[ 71.109376] hub 4-0:1.0: USB hub found
[ 71.109383] hub 4-0:1.0: 2 ports detected
[ 71.213117] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.213130] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 71.213155] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 71.213179] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 71.213299] usb usb5: configuration #1 chosen from 1 choice
[ 71.213325] hub 5-0:1.0: USB hub found
[ 71.213332] hub 5-0:1.0: 2 ports detected
[ 71.317585] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 71.319838] Audigy2 value: Special config.
[ 73.765264] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 73.765268] Copyright (c) 1999-2006 Intel Corporation.
[ 73.765309] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 73.765314] PCI: Disallowing DAC for device 0000:00:0e.0
[ 74.025736] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 74.201234] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 74.355702] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 74.355715] ReiserFS: hdb1: using ordered data mode
[ 74.392680] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.394057] ReiserFS: hdb1: checking transaction log (hdb1)
[ 74.489291] ReiserFS: hdb1: Using r5 hash to sort names
[ 74.553988] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 74.553998] ReiserFS: hda2: using ordered data mode
[ 74.558818] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.560151] ReiserFS: hda2: checking transaction log (hda2)
[ 74.623128] ReiserFS: hda2: Using r5 hash to sort names
[ 80.456682] hda: UDMA/100 mode selected
[ 80.460729] hdb: UDMA/133 mode selected
[ 80.515263] hdc: UDMA/33 mode selected
[ 80.532803] hdd: UDMA/33 mode selected
[ 83.053804] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 87.342494] w83627hf: Found W83697HF chip at 0x290
[ 159.125858] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 159.125863] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 159.125866] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 159.125869] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 159.125871] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 159.125874] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 159.125876] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 159.125880] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 159.125883] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 159.125886] ata1: SError: { 10B8B }
[ 159.125890] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125895] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125899] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125904] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125908] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125912] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125917] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125923] ata1.15: hard resetting link
[ 164.216778] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 164.468696] ata1.15: qc timeout (cmd 0xe4)
[ 164.468703] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 164.468706] ata1.15: PMP revalidation failed (errno=-5)
[ 164.468708] ata1.15: retrying hardreset in 5 secs
[ 169.471177] ata1.15: hard resetting link
[ 174.565637] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 174.817555] ata1.15: qc timeout (cmd 0xe4)
[ 174.817562] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 174.817565] ata1.15: PMP revalidation failed (errno=-5)
[ 174.817568] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 174.817570] ata1.15: retrying hardreset in 5 secs
[ 179.820043] ata1.15: hard resetting link
[ 182.019380] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 182.019590] ata1.00: hard resetting link
[ 182.339460] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 182.339463] ata1.01: hard resetting link
[ 182.659362] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.659365] ata1.02: hard resetting link
[ 182.979265] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.979269] ata1.03: hard resetting link
[ 183.299169] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 183.299172] ata1.04: hard resetting link
[ 183.619071] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 183.619074] ata1.05: hard resetting link
[ 183.938971] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 183.938975] ata1.06: hard resetting link
[ 184.258874] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 184.261106] ata1.00: configured for UDMA/100
[ 184.263303] ata1.01: configured for UDMA/100
[ 184.263398] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 184.263401] ata1.02: revalidation failed (errno=-5)
[ 184.263406] ata1.15: hard resetting link
[ 186.462034] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 186.462308] ata1.00: hard resetting link
[ 186.782113] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 186.782117] ata1.01: hard resetting link
[ 187.102015] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.102018] ata1.02: hard resetting link
[ 187.421918] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.421922] ata1.03: hard resetting link
[ 187.741820] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.741823] ata1.04: hard resetting link
[ 188.061723] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 188.061727] ata1.05: hard resetting link
[ 188.381625] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 188.381628] ata1.06: hard resetting link
[ 188.701528] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 188.703706] ata1.00: configured for UDMA/100
[ 188.705935] ata1.01: configured for UDMA/100
[ 188.811817] ata1.02: configured for UDMA/100
[ 188.915919] ata1.03: configured for UDMA/100
[ 188.916051] ata1.05: device is on DMA blacklist, disabling DMA
[ 188.916182] ata1.05: configured for PIO4
[ 188.916453] ata1: EH complete
[ 188.916481] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916492] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916496] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916508] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916524] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916532] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916535] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916546] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916560] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916567] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916570] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916581] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916595] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916602] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916605] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916616] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916629] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916637] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916640] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916651] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916664] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916671] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916674] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916686] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916698] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916705] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916708] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916720] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916732] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916739] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916742] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916753] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916766] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916773] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916776] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916787] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916799] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916807] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916810] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916821] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 233.874452] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 233.874458] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 233.874462] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 233.874465] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 233.874468] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 233.874471] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 233.874474] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 233.874478] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 233.874482] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 233.874486] ata1: SError: { 10B8B }
[ 233.874490] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874495] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874501] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874506] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874511] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874516] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874521] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874529] ata1.15: hard resetting link
[ 238.966100] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 239.218017] ata1.15: qc timeout (cmd 0xe4)
[ 239.218026] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 239.218029] ata1.15: PMP revalidation failed (errno=-5)
[ 239.218032] ata1.15: retrying hardreset in 5 secs
[ 244.220499] ata1.15: hard resetting link
[ 249.314958] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 249.566876] ata1.15: qc timeout (cmd 0xe4)
[ 249.566883] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 249.566886] ata1.15: PMP revalidation failed (errno=-5)
[ 249.566890] ata1.15: retrying hardreset in 5 secs
[ 254.569359] ata1.15: hard resetting link
[ 256.768701] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 256.768897] ata1.00: hard resetting link
[ 257.088783] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 257.088787] ata1.01: hard resetting link
[ 257.408684] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.408688] ata1.02: hard resetting link
[ 257.728587] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.728591] ata1.03: hard resetting link
[ 258.048491] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 258.048495] ata1.04: hard resetting link
[ 258.368394] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 258.368397] ata1.05: hard resetting link
[ 258.688294] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 258.688298] ata1.06: hard resetting link
[ 259.008199] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 259.008295] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 259.008299] ata1.00: revalidation failed (errno=-5)
[ 259.008304] ata1.15: hard resetting link
[ 261.207356] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 261.207634] ata1.00: hard resetting link
[ 261.527434] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 261.527439] ata1.01: hard resetting link
[ 261.847337] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 261.847340] ata1.02: hard resetting link
[ 262.167238] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.167242] ata1.03: hard resetting link
[ 262.487142] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.487146] ata1.04: hard resetting link
[ 262.807046] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 262.807050] ata1.05: hard resetting link
[ 263.126946] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 263.126950] ata1.06: hard resetting link
[ 263.446852] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 263.449093] ata1.00: configured for UDMA/100
[ 263.451311] ata1.01: configured for UDMA/100
[ 263.556976] ata1.02: configured for UDMA/100
[ 263.658661] ata1.03: configured for UDMA/100
[ 263.658793] ata1.05: device is on DMA blacklist, disabling DMA
[ 263.658923] ata1.05: configured for PIO4
[ 263.659192] ata1: EH complete
[ 263.659218] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659229] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659232] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659245] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659260] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659267] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659270] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659281] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659295] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659303] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659305] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659317] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659330] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659337] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659340] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659351] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659365] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659372] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659375] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659386] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659399] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659407] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659409] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659421] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659433] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659440] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659443] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659454] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659467] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659474] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659477] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659488] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659500] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659508] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659511] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659522] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659534] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659541] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659544] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659555] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 337.619074] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 337.619079] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 337.619083] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 337.619086] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 337.619089] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 337.619092] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 337.619095] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 337.619099] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 337.619103] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 337.619107] ata1: SError: { 10B8B }
[ 337.619111] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619116] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619122] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619127] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619132] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619137] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619142] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619150] ata1.15: hard resetting link
[ 339.695540] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 339.947457] ata1.15: qc timeout (cmd 0xe4)
[ 339.947465] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 339.947469] ata1.15: PMP revalidation failed (errno=-5)
[ 339.947472] ata1.15: retrying hardreset in 5 secs
[ 344.949939] ata1.15: hard resetting link
[ 347.029314] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 347.281232] ata1.15: qc timeout (cmd 0xe4)
[ 347.281239] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 347.281242] ata1.15: PMP revalidation failed (errno=-5)
[ 347.281246] ata1.15: retrying hardreset in 5 secs
[ 352.283714] ata1.15: hard resetting link
[ 356.250521] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 356.250717] ata1.00: hard resetting link
[ 356.570601] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 356.570605] ata1.01: hard resetting link
[ 356.890503] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 356.890507] ata1.02: hard resetting link
[ 357.210406] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.210411] ata1.03: hard resetting link
[ 357.530309] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.530313] ata1.04: hard resetting link
[ 357.850212] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 357.850216] ata1.05: hard resetting link
[ 358.170112] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 358.170116] ata1.06: hard resetting link
[ 358.490020] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 358.492276] ata1.00: configured for UDMA/100
[ 358.494506] ata1.01: configured for UDMA/100
[ 358.595946] ata1.02: configured for UDMA/100
[ 358.705215] ata1.03: configured for UDMA/100
[ 358.705316] ata1.05: device is on DMA blacklist, disabling DMA
[ 358.705472] ata1.05: configured for PIO4
[ 358.705734] ata1: EH complete
[ 358.705759] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705773] sd 1:0:0:0: [sdb] Write Protect is off
[ 358.705776] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 358.705789] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705804] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705812] sd 1:1:0:0: [sdc] Write Protect is off
[ 358.705815] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 358.705827] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705841] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705849] sd 1:2:0:0: [sdd] Write Protect is off
[ 358.705852] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 358.705863] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705877] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705885] sd 1:3:0:0: [sde] Write Protect is off
[ 358.705888] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 358.705900] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705913] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 358.705921] sd 1:5:0:0: [sdf] Write Protect is off
[ 358.705924] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 358.705936] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705949] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705957] sd 1:0:0:0: [sdb] Write Protect is off
[ 358.705960] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 358.705972] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705985] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705992] sd 1:1:0:0: [sdc] Write Protect is off
[ 358.705995] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 358.706007] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706020] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 358.706028] sd 1:2:0:0: [sdd] Write Protect is off
[ 358.706030] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 358.706042] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706055] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 358.706063] sd 1:3:0:0: [sde] Write Protect is off
[ 358.706066] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 358.706077] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706090] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 358.706098] sd 1:5:0:0: [sdf] Write Protect is off
[ 358.706101] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 358.706112] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 404.739637] ata1.15: limiting speed to UDMA7:PIO5
[ 404.739644] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 404.739648] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 404.739651] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 404.739654] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 404.739657] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 404.739660] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 404.739663] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 404.739667] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 404.739671] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 404.739675] ata1: SError: { 10B8B }
[ 404.739679] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739685] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739690] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739695] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739700] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739705] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739710] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739718] ata1.15: hard resetting link
[ 409.830262] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 410.082180] ata1.15: qc timeout (cmd 0xe4)
[ 410.082188] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 410.082191] ata1.15: PMP revalidation failed (errno=-5)
[ 410.082194] ata1.15: retrying hardreset in 5 secs
[ 415.084662] ata1.15: hard resetting link
[ 420.179121] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 420.431039] ata1.15: qc timeout (cmd 0xe4)
[ 420.431047] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 420.431050] ata1.15: PMP revalidation failed (errno=-5)
[ 420.431054] ata1.15: retrying hardreset in 5 secs
[ 425.433523] ata1.15: hard resetting link
[ 435.438490] ata1.15: softreset failed (timeout)
[ 435.438494] ata1.15: hard resetting link
[ 445.443457] ata1.15: softreset failed (timeout)
[ 445.443463] ata1.15: hard resetting link
[ 480.432842] ata1.15: softreset failed (timeout)
[ 480.432850] ata1.15: hard resetting link
[ 485.431325] ata1.15: softreset failed (timeout)
[ 485.431329] ata1.15: failed to reset PMP, giving up
[ 485.431332] ata1.15: Port Multiplier detaching
[ 485.431340] ata1.00: disabled
[ 485.431343] ata1.01: disabled
[ 485.431346] ata1.02: disabled
[ 485.431348] ata1.03: disabled
[ 485.431350] ata1.05: disabled
[ 485.431354] ata1.00: disabled
[ 485.431360] ata1: hard resetting link
[ 495.436287] ata1: softreset failed (timeout)
[ 495.436290] ata1: hard resetting link
[ 505.441252] ata1: softreset failed (timeout)
[ 505.441255] ata1: hard resetting link
[ 540.430639] ata1: softreset failed (timeout)
[ 540.430647] ata1: limiting SATA link speed to 1.5 Gbps
[ 540.430650] ata1: hard resetting link
[ 545.525097] ata1: SATA link down (SStatus 1 SControl 10)
[ 545.525115] ata1: EH complete
[ 545.525125] ata1.00: detaching (SCSI 1:0:0:0)
[ 545.525299] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 545.525613] sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525617] sd 1:0:0:0: [sdb] Stopping disk
[ 545.525623] sd 1:0:0:0: [sdb] START_STOP FAILED
[ 545.525626] sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525663] ata1.01: detaching (SCSI 1:1:0:0)
[ 545.525799] sd 1:1:0:0: [sdc] Synchronizing SCSI cache
[ 545.525944] sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525948] sd 1:1:0:0: [sdc] Stopping disk
[ 545.525970] sd 1:1:0:0: [sdc] START_STOP FAILED
[ 545.525972] sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
[ 545.526000] ata1.02: detaching (SCSI 1:2:0:0)
[ 545.526146] sd 1:2:0:0: [sdd] Synchronizing SCSI cache
[ 545.527048] sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527053] sd 1:2:0:0: [sdd] Stopping disk
[ 545.527071] sd 1:2:0:0: [sdd] START_STOP FAILED
[ 545.527074] sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527106] ata1.03: detaching (SCSI 1:3:0:0)
[ 545.527246] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 545.527287] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527290] sd 1:3:0:0: [sde] Stopping disk
[ 545.527304] sd 1:3:0:0: [sde] START_STOP FAILED
[ 545.527306] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527333] ata1.05: detaching (SCSI 1:5:0:0)
[ 545.527451] sd 1:5:0:0: [sdf] Stopping disk
[ 545.527459] sd 1:5:0:0: [sdf] START_STOP FAILED
[ 545.527462] sd 1:5:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
[ 559.279656] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xa frozen
[ 559.279662] ata1: irq_stat 0x00a40080, device exchanged
[ 559.279673] ata1: hard resetting link
[ 563.427669] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 563.679583] ata1.15: qc timeout (cmd 0xe4)
[ 563.679589] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 563.679593] ata1: failed to recover some devices, retrying in 5 secs
[ 568.682071] ata1: hard resetting link
[ 578.687033] ata1: softreset failed (timeout)
[ 578.687039] ata1: hard resetting link
[ 588.691996] ata1: softreset failed (timeout)
[ 588.691999] ata1: hard resetting link
[ 623.681382] ata1: softreset failed (timeout)
[ 623.681390] ata1: limiting SATA link speed to 1.5 Gbps
[ 623.681393] ata1: hard resetting link
[ 628.679864] ata1: softreset failed (timeout)
[ 628.679867] ata1: reset failed, giving up
[ 628.679878] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xa frozen t4
[ 628.679883] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 628.679892] ata1: hard resetting link
[ 638.684830] ata1: softreset failed (timeout)
[ 638.684836] ata1: hard resetting link
[ 648.689795] ata1: softreset failed (timeout)
[ 648.689801] ata1: hard resetting link
[ 683.679179] ata1: softreset failed (timeout)
[ 683.679186] ata1: limiting SATA link speed to 1.5 Gbps
[ 683.679189] ata1: hard resetting link
[ 688.677661] ata1: softreset failed (timeout)
[ 688.677664] ata1: reset failed, giving up
[ 688.677670] ata1: EH complete
[ 776.735711] ata2: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
[ 776.735717] ata2: irq_stat 0x00a40080, device exchanged
[ 776.735721] ata2: SError: { PHYRdyChg }
[ 776.735731] ata2: hard resetting link
[ 786.739911] ata2: softreset failed (timeout)
[ 786.739918] ata2: hard resetting link
[ 796.744875] ata2: softreset failed (timeout)
[ 796.744881] ata2: hard resetting link
[ 831.734261] ata2: softreset failed (timeout)
[ 831.734268] ata2: limiting SATA link speed to 1.5 Gbps
[ 831.734271] ata2: hard resetting link
[ 836.732744] ata2: softreset failed (timeout)
[ 836.732747] ata2: reset failed, giving up
[ 836.732753] ata2: EH complete
[ 1001.096027] ACPI: PCI interrupt for device 0000:00:0c.0 disabled
[-- Attachment #7: 6_ModuleReload.log --]
[-- Type: text/plain, Size: 31247 bytes --]
> IRQ 21
[ 71.005204] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 71.005229] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 71.005252] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
[ 71.005373] usb usb3: configuration #1 chosen from 1 choice
[ 71.005398] hub 3-0:1.0: USB hub found
[ 71.005405] hub 3-0:1.0: 2 ports detected
[ 71.109172] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.109185] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 71.109211] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 71.109235] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
[ 71.109351] usb usb4: configuration #1 chosen from 1 choice
[ 71.109376] hub 4-0:1.0: USB hub found
[ 71.109383] hub 4-0:1.0: 2 ports detected
[ 71.213117] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 71.213130] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 71.213155] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 71.213179] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c800
[ 71.213299] usb usb5: configuration #1 chosen from 1 choice
[ 71.213325] hub 5-0:1.0: USB hub found
[ 71.213332] hub 5-0:1.0: 2 ports detected
[ 71.317585] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 71.319838] Audigy2 value: Special config.
[ 73.765264] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 73.765268] Copyright (c) 1999-2006 Intel Corporation.
[ 73.765309] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 73.765314] PCI: Disallowing DAC for device 0000:00:0e.0
[ 74.025736] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 74.201234] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 74.355702] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 74.355715] ReiserFS: hdb1: using ordered data mode
[ 74.392680] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.394057] ReiserFS: hdb1: checking transaction log (hdb1)
[ 74.489291] ReiserFS: hdb1: Using r5 hash to sort names
[ 74.553988] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 74.553998] ReiserFS: hda2: using ordered data mode
[ 74.558818] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.560151] ReiserFS: hda2: checking transaction log (hda2)
[ 74.623128] ReiserFS: hda2: Using r5 hash to sort names
[ 80.456682] hda: UDMA/100 mode selected
[ 80.460729] hdb: UDMA/133 mode selected
[ 80.515263] hdc: UDMA/33 mode selected
[ 80.532803] hdd: UDMA/33 mode selected
[ 83.053804] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 87.342494] w83627hf: Found W83697HF chip at 0x290
[ 159.125858] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 159.125863] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 159.125866] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 159.125869] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 159.125871] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 159.125874] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 159.125876] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 159.125880] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 159.125883] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 159.125886] ata1: SError: { 10B8B }
[ 159.125890] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125895] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125899] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125904] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125908] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125912] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125917] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125923] ata1.15: hard resetting link
[ 164.216778] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 164.468696] ata1.15: qc timeout (cmd 0xe4)
[ 164.468703] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 164.468706] ata1.15: PMP revalidation failed (errno=-5)
[ 164.468708] ata1.15: retrying hardreset in 5 secs
[ 169.471177] ata1.15: hard resetting link
[ 174.565637] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 174.817555] ata1.15: qc timeout (cmd 0xe4)
[ 174.817562] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 174.817565] ata1.15: PMP revalidation failed (errno=-5)
[ 174.817568] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 174.817570] ata1.15: retrying hardreset in 5 secs
[ 179.820043] ata1.15: hard resetting link
[ 182.019380] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 182.019590] ata1.00: hard resetting link
[ 182.339460] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 182.339463] ata1.01: hard resetting link
[ 182.659362] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.659365] ata1.02: hard resetting link
[ 182.979265] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.979269] ata1.03: hard resetting link
[ 183.299169] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 183.299172] ata1.04: hard resetting link
[ 183.619071] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 183.619074] ata1.05: hard resetting link
[ 183.938971] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 183.938975] ata1.06: hard resetting link
[ 184.258874] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 184.261106] ata1.00: configured for UDMA/100
[ 184.263303] ata1.01: configured for UDMA/100
[ 184.263398] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 184.263401] ata1.02: revalidation failed (errno=-5)
[ 184.263406] ata1.15: hard resetting link
[ 186.462034] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 186.462308] ata1.00: hard resetting link
[ 186.782113] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 186.782117] ata1.01: hard resetting link
[ 187.102015] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.102018] ata1.02: hard resetting link
[ 187.421918] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.421922] ata1.03: hard resetting link
[ 187.741820] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.741823] ata1.04: hard resetting link
[ 188.061723] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 188.061727] ata1.05: hard resetting link
[ 188.381625] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 188.381628] ata1.06: hard resetting link
[ 188.701528] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 188.703706] ata1.00: configured for UDMA/100
[ 188.705935] ata1.01: configured for UDMA/100
[ 188.811817] ata1.02: configured for UDMA/100
[ 188.915919] ata1.03: configured for UDMA/100
[ 188.916051] ata1.05: device is on DMA blacklist, disabling DMA
[ 188.916182] ata1.05: configured for PIO4
[ 188.916453] ata1: EH complete
[ 188.916481] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916492] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916496] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916508] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916524] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916532] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916535] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916546] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916560] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916567] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916570] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916581] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916595] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916602] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916605] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916616] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916629] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916637] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916640] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916651] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916664] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916671] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916674] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916686] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916698] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916705] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916708] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916720] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916732] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916739] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916742] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916753] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916766] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916773] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916776] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916787] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916799] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916807] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916810] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916821] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 233.874452] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 233.874458] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 233.874462] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 233.874465] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 233.874468] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 233.874471] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 233.874474] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 233.874478] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 233.874482] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 233.874486] ata1: SError: { 10B8B }
[ 233.874490] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874495] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874501] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874506] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874511] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874516] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874521] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874529] ata1.15: hard resetting link
[ 238.966100] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 239.218017] ata1.15: qc timeout (cmd 0xe4)
[ 239.218026] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 239.218029] ata1.15: PMP revalidation failed (errno=-5)
[ 239.218032] ata1.15: retrying hardreset in 5 secs
[ 244.220499] ata1.15: hard resetting link
[ 249.314958] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 249.566876] ata1.15: qc timeout (cmd 0xe4)
[ 249.566883] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 249.566886] ata1.15: PMP revalidation failed (errno=-5)
[ 249.566890] ata1.15: retrying hardreset in 5 secs
[ 254.569359] ata1.15: hard resetting link
[ 256.768701] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 256.768897] ata1.00: hard resetting link
[ 257.088783] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 257.088787] ata1.01: hard resetting link
[ 257.408684] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.408688] ata1.02: hard resetting link
[ 257.728587] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.728591] ata1.03: hard resetting link
[ 258.048491] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 258.048495] ata1.04: hard resetting link
[ 258.368394] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 258.368397] ata1.05: hard resetting link
[ 258.688294] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 258.688298] ata1.06: hard resetting link
[ 259.008199] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 259.008295] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 259.008299] ata1.00: revalidation failed (errno=-5)
[ 259.008304] ata1.15: hard resetting link
[ 261.207356] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 261.207634] ata1.00: hard resetting link
[ 261.527434] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 261.527439] ata1.01: hard resetting link
[ 261.847337] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 261.847340] ata1.02: hard resetting link
[ 262.167238] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.167242] ata1.03: hard resetting link
[ 262.487142] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.487146] ata1.04: hard resetting link
[ 262.807046] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 262.807050] ata1.05: hard resetting link
[ 263.126946] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 263.126950] ata1.06: hard resetting link
[ 263.446852] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 263.449093] ata1.00: configured for UDMA/100
[ 263.451311] ata1.01: configured for UDMA/100
[ 263.556976] ata1.02: configured for UDMA/100
[ 263.658661] ata1.03: configured for UDMA/100
[ 263.658793] ata1.05: device is on DMA blacklist, disabling DMA
[ 263.658923] ata1.05: configured for PIO4
[ 263.659192] ata1: EH complete
[ 263.659218] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659229] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659232] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659245] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659260] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659267] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659270] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659281] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659295] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659303] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659305] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659317] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659330] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659337] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659340] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659351] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659365] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659372] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659375] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659386] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659399] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659407] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659409] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659421] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659433] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659440] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659443] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659454] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659467] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659474] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659477] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659488] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659500] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659508] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659511] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659522] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659534] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659541] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659544] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659555] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 337.619074] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 337.619079] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 337.619083] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 337.619086] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 337.619089] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 337.619092] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 337.619095] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 337.619099] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 337.619103] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 337.619107] ata1: SError: { 10B8B }
[ 337.619111] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619116] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619122] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619127] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619132] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619137] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619142] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619150] ata1.15: hard resetting link
[ 339.695540] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 339.947457] ata1.15: qc timeout (cmd 0xe4)
[ 339.947465] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 339.947469] ata1.15: PMP revalidation failed (errno=-5)
[ 339.947472] ata1.15: retrying hardreset in 5 secs
[ 344.949939] ata1.15: hard resetting link
[ 347.029314] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 347.281232] ata1.15: qc timeout (cmd 0xe4)
[ 347.281239] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 347.281242] ata1.15: PMP revalidation failed (errno=-5)
[ 347.281246] ata1.15: retrying hardreset in 5 secs
[ 352.283714] ata1.15: hard resetting link
[ 356.250521] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 356.250717] ata1.00: hard resetting link
[ 356.570601] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 356.570605] ata1.01: hard resetting link
[ 356.890503] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 356.890507] ata1.02: hard resetting link
[ 357.210406] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.210411] ata1.03: hard resetting link
[ 357.530309] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.530313] ata1.04: hard resetting link
[ 357.850212] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 357.850216] ata1.05: hard resetting link
[ 358.170112] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 358.170116] ata1.06: hard resetting link
[ 358.490020] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 358.492276] ata1.00: configured for UDMA/100
[ 358.494506] ata1.01: configured for UDMA/100
[ 358.595946] ata1.02: configured for UDMA/100
[ 358.705215] ata1.03: configured for UDMA/100
[ 358.705316] ata1.05: device is on DMA blacklist, disabling DMA
[ 358.705472] ata1.05: configured for PIO4
[ 358.705734] ata1: EH complete
[ 358.705759] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705773] sd 1:0:0:0: [sdb] Write Protect is off
[ 358.705776] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 358.705789] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705804] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705812] sd 1:1:0:0: [sdc] Write Protect is off
[ 358.705815] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 358.705827] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705841] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705849] sd 1:2:0:0: [sdd] Write Protect is off
[ 358.705852] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 358.705863] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705877] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705885] sd 1:3:0:0: [sde] Write Protect is off
[ 358.705888] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 358.705900] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705913] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 358.705921] sd 1:5:0:0: [sdf] Write Protect is off
[ 358.705924] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 358.705936] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705949] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705957] sd 1:0:0:0: [sdb] Write Protect is off
[ 358.705960] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 358.705972] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705985] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705992] sd 1:1:0:0: [sdc] Write Protect is off
[ 358.705995] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 358.706007] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706020] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 358.706028] sd 1:2:0:0: [sdd] Write Protect is off
[ 358.706030] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 358.706042] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706055] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 358.706063] sd 1:3:0:0: [sde] Write Protect is off
[ 358.706066] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 358.706077] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706090] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 358.706098] sd 1:5:0:0: [sdf] Write Protect is off
[ 358.706101] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 358.706112] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 404.739637] ata1.15: limiting speed to UDMA7:PIO5
[ 404.739644] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 404.739648] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 404.739651] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 404.739654] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 404.739657] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 404.739660] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 404.739663] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 404.739667] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 404.739671] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 404.739675] ata1: SError: { 10B8B }
[ 404.739679] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739685] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739690] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739695] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739700] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739705] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739710] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739718] ata1.15: hard resetting link
[ 409.830262] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 410.082180] ata1.15: qc timeout (cmd 0xe4)
[ 410.082188] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 410.082191] ata1.15: PMP revalidation failed (errno=-5)
[ 410.082194] ata1.15: retrying hardreset in 5 secs
[ 415.084662] ata1.15: hard resetting link
[ 420.179121] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 420.431039] ata1.15: qc timeout (cmd 0xe4)
[ 420.431047] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 420.431050] ata1.15: PMP revalidation failed (errno=-5)
[ 420.431054] ata1.15: retrying hardreset in 5 secs
[ 425.433523] ata1.15: hard resetting link
[ 435.438490] ata1.15: softreset failed (timeout)
[ 435.438494] ata1.15: hard resetting link
[ 445.443457] ata1.15: softreset failed (timeout)
[ 445.443463] ata1.15: hard resetting link
[ 480.432842] ata1.15: softreset failed (timeout)
[ 480.432850] ata1.15: hard resetting link
[ 485.431325] ata1.15: softreset failed (timeout)
[ 485.431329] ata1.15: failed to reset PMP, giving up
[ 485.431332] ata1.15: Port Multiplier detaching
[ 485.431340] ata1.00: disabled
[ 485.431343] ata1.01: disabled
[ 485.431346] ata1.02: disabled
[ 485.431348] ata1.03: disabled
[ 485.431350] ata1.05: disabled
[ 485.431354] ata1.00: disabled
[ 485.431360] ata1: hard resetting link
[ 495.436287] ata1: softreset failed (timeout)
[ 495.436290] ata1: hard resetting link
[ 505.441252] ata1: softreset failed (timeout)
[ 505.441255] ata1: hard resetting link
[ 540.430639] ata1: softreset failed (timeout)
[ 540.430647] ata1: limiting SATA link speed to 1.5 Gbps
[ 540.430650] ata1: hard resetting link
[ 545.525097] ata1: SATA link down (SStatus 1 SControl 10)
[ 545.525115] ata1: EH complete
[ 545.525125] ata1.00: detaching (SCSI 1:0:0:0)
[ 545.525299] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 545.525613] sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525617] sd 1:0:0:0: [sdb] Stopping disk
[ 545.525623] sd 1:0:0:0: [sdb] START_STOP FAILED
[ 545.525626] sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525663] ata1.01: detaching (SCSI 1:1:0:0)
[ 545.525799] sd 1:1:0:0: [sdc] Synchronizing SCSI cache
[ 545.525944] sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525948] sd 1:1:0:0: [sdc] Stopping disk
[ 545.525970] sd 1:1:0:0: [sdc] START_STOP FAILED
[ 545.525972] sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
[ 545.526000] ata1.02: detaching (SCSI 1:2:0:0)
[ 545.526146] sd 1:2:0:0: [sdd] Synchronizing SCSI cache
[ 545.527048] sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527053] sd 1:2:0:0: [sdd] Stopping disk
[ 545.527071] sd 1:2:0:0: [sdd] START_STOP FAILED
[ 545.527074] sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527106] ata1.03: detaching (SCSI 1:3:0:0)
[ 545.527246] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 545.527287] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527290] sd 1:3:0:0: [sde] Stopping disk
[ 545.527304] sd 1:3:0:0: [sde] START_STOP FAILED
[ 545.527306] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527333] ata1.05: detaching (SCSI 1:5:0:0)
[ 545.527451] sd 1:5:0:0: [sdf] Stopping disk
[ 545.527459] sd 1:5:0:0: [sdf] START_STOP FAILED
[ 545.527462] sd 1:5:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
[ 559.279656] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xa frozen
[ 559.279662] ata1: irq_stat 0x00a40080, device exchanged
[ 559.279673] ata1: hard resetting link
[ 563.427669] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 563.679583] ata1.15: qc timeout (cmd 0xe4)
[ 563.679589] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 563.679593] ata1: failed to recover some devices, retrying in 5 secs
[ 568.682071] ata1: hard resetting link
[ 578.687033] ata1: softreset failed (timeout)
[ 578.687039] ata1: hard resetting link
[ 588.691996] ata1: softreset failed (timeout)
[ 588.691999] ata1: hard resetting link
[ 623.681382] ata1: softreset failed (timeout)
[ 623.681390] ata1: limiting SATA link speed to 1.5 Gbps
[ 623.681393] ata1: hard resetting link
[ 628.679864] ata1: softreset failed (timeout)
[ 628.679867] ata1: reset failed, giving up
[ 628.679878] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xa frozen t4
[ 628.679883] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 628.679892] ata1: hard resetting link
[ 638.684830] ata1: softreset failed (timeout)
[ 638.684836] ata1: hard resetting link
[ 648.689795] ata1: softreset failed (timeout)
[ 648.689801] ata1: hard resetting link
[ 683.679179] ata1: softreset failed (timeout)
[ 683.679186] ata1: limiting SATA link speed to 1.5 Gbps
[ 683.679189] ata1: hard resetting link
[ 688.677661] ata1: softreset failed (timeout)
[ 688.677664] ata1: reset failed, giving up
[ 688.677670] ata1: EH complete
[ 776.735711] ata2: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
[ 776.735717] ata2: irq_stat 0x00a40080, device exchanged
[ 776.735721] ata2: SError: { PHYRdyChg }
[ 776.735731] ata2: hard resetting link
[ 786.739911] ata2: softreset failed (timeout)
[ 786.739918] ata2: hard resetting link
[ 796.744875] ata2: softreset failed (timeout)
[ 796.744881] ata2: hard resetting link
[ 831.734261] ata2: softreset failed (timeout)
[ 831.734268] ata2: limiting SATA link speed to 1.5 Gbps
[ 831.734271] ata2: hard resetting link
[ 836.732744] ata2: softreset failed (timeout)
[ 836.732747] ata2: reset failed, giving up
[ 836.732753] ata2: EH complete
[ 1001.096027] ACPI: PCI interrupt for device 0000:00:0c.0 disabled
[ 1051.175431] sata_sil24 0000:00:0c.0: version 1.1
[ 1051.175576] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 1051.175960] PCI: Disallowing DAC for device 0000:00:0c.0
[ 1051.176552] scsi5 : sata_sil24
[ 1051.177500] scsi6 : sata_sil24
[ 1051.178092] scsi7 : sata_sil24
[ 1051.178658] scsi8 : sata_sil24
[ 1051.178696] ata5: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
[ 1051.178701] ata6: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
[ 1051.178705] ata7: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
[ 1051.178709] ata8: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
[ 1061.180649] ata5: softreset failed (timeout)
[ 1071.185612] ata5: softreset failed (timeout)
[ 1106.174999] ata5: softreset failed (timeout)
[ 1111.173481] ata5: softreset failed (timeout)
[ 1111.173484] ata5: reset failed, giving up
[ 1116.267939] ata6: SATA link down (SStatus 1 SControl 10)
[ 1118.347308] ata7: SATA link down (SStatus 0 SControl 0)
[ 1120.426676] ata8: SATA link down (SStatus 0 SControl 0)
[-- Attachment #8: 7_ModuleReload2.log --]
[-- Type: text/plain, Size: 31241 bytes --]
found
[ 71.213332] hub 5-0:1.0: 2 ports detected
[ 71.317585] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 71.319838] Audigy2 value: Special config.
[ 73.765264] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 73.765268] Copyright (c) 1999-2006 Intel Corporation.
[ 73.765309] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 73.765314] PCI: Disallowing DAC for device 0000:00:0e.0
[ 74.025736] e1000: 0000:00:0e.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:62:c5:46
[ 74.201234] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 74.355702] ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
[ 74.355715] ReiserFS: hdb1: using ordered data mode
[ 74.392680] ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.394057] ReiserFS: hdb1: checking transaction log (hdb1)
[ 74.489291] ReiserFS: hdb1: Using r5 hash to sort names
[ 74.553988] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 74.553998] ReiserFS: hda2: using ordered data mode
[ 74.558818] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 74.560151] ReiserFS: hda2: checking transaction log (hda2)
[ 74.623128] ReiserFS: hda2: Using r5 hash to sort names
[ 80.456682] hda: UDMA/100 mode selected
[ 80.460729] hdb: UDMA/133 mode selected
[ 80.515263] hdc: UDMA/33 mode selected
[ 80.532803] hdd: UDMA/33 mode selected
[ 83.053804] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 87.342494] w83627hf: Found W83697HF chip at 0x290
[ 159.125858] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 159.125863] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 159.125866] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 159.125869] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 159.125871] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 159.125874] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 159.125876] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 159.125880] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 159.125883] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 159.125886] ata1: SError: { 10B8B }
[ 159.125890] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125895] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125899] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125904] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125908] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125912] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125917] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 159.125923] ata1.15: hard resetting link
[ 164.216778] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 164.468696] ata1.15: qc timeout (cmd 0xe4)
[ 164.468703] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 164.468706] ata1.15: PMP revalidation failed (errno=-5)
[ 164.468708] ata1.15: retrying hardreset in 5 secs
[ 169.471177] ata1.15: hard resetting link
[ 174.565637] ata1.15: SATA link down (SStatus 1 SControl 0)
[ 174.817555] ata1.15: qc timeout (cmd 0xe4)
[ 174.817562] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 174.817565] ata1.15: PMP revalidation failed (errno=-5)
[ 174.817568] ata1.15: limiting SATA link speed to 1.5 Gbps
[ 174.817570] ata1.15: retrying hardreset in 5 secs
[ 179.820043] ata1.15: hard resetting link
[ 182.019380] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 182.019590] ata1.00: hard resetting link
[ 182.339460] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 182.339463] ata1.01: hard resetting link
[ 182.659362] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.659365] ata1.02: hard resetting link
[ 182.979265] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 182.979269] ata1.03: hard resetting link
[ 183.299169] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 183.299172] ata1.04: hard resetting link
[ 183.619071] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 183.619074] ata1.05: hard resetting link
[ 183.938971] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 183.938975] ata1.06: hard resetting link
[ 184.258874] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 184.261106] ata1.00: configured for UDMA/100
[ 184.263303] ata1.01: configured for UDMA/100
[ 184.263398] ata1.02: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 184.263401] ata1.02: revalidation failed (errno=-5)
[ 184.263406] ata1.15: hard resetting link
[ 186.462034] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 186.462308] ata1.00: hard resetting link
[ 186.782113] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 186.782117] ata1.01: hard resetting link
[ 187.102015] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.102018] ata1.02: hard resetting link
[ 187.421918] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.421922] ata1.03: hard resetting link
[ 187.741820] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 187.741823] ata1.04: hard resetting link
[ 188.061723] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 188.061727] ata1.05: hard resetting link
[ 188.381625] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 188.381628] ata1.06: hard resetting link
[ 188.701528] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 188.703706] ata1.00: configured for UDMA/100
[ 188.705935] ata1.01: configured for UDMA/100
[ 188.811817] ata1.02: configured for UDMA/100
[ 188.915919] ata1.03: configured for UDMA/100
[ 188.916051] ata1.05: device is on DMA blacklist, disabling DMA
[ 188.916182] ata1.05: configured for PIO4
[ 188.916453] ata1: EH complete
[ 188.916481] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916492] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916496] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916508] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916524] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916532] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916535] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916546] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916560] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916567] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916570] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916581] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916595] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916602] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916605] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916616] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916629] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916637] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916640] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916651] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916664] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916671] sd 1:0:0:0: [sdb] Write Protect is off
[ 188.916674] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 188.916686] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916698] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916705] sd 1:1:0:0: [sdc] Write Protect is off
[ 188.916708] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 188.916720] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916732] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916739] sd 1:2:0:0: [sdd] Write Protect is off
[ 188.916742] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 188.916753] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916766] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 188.916773] sd 1:3:0:0: [sde] Write Protect is off
[ 188.916776] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 188.916787] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 188.916799] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 188.916807] sd 1:5:0:0: [sdf] Write Protect is off
[ 188.916810] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 188.916821] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 233.874452] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 233.874458] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 233.874462] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 233.874465] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 233.874468] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 233.874471] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 233.874474] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 233.874478] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 233.874482] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 233.874486] ata1: SError: { 10B8B }
[ 233.874490] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874495] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874501] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874506] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874511] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874516] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874521] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 233.874529] ata1.15: hard resetting link
[ 238.966100] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 239.218017] ata1.15: qc timeout (cmd 0xe4)
[ 239.218026] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 239.218029] ata1.15: PMP revalidation failed (errno=-5)
[ 239.218032] ata1.15: retrying hardreset in 5 secs
[ 244.220499] ata1.15: hard resetting link
[ 249.314958] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 249.566876] ata1.15: qc timeout (cmd 0xe4)
[ 249.566883] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 249.566886] ata1.15: PMP revalidation failed (errno=-5)
[ 249.566890] ata1.15: retrying hardreset in 5 secs
[ 254.569359] ata1.15: hard resetting link
[ 256.768701] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 256.768897] ata1.00: hard resetting link
[ 257.088783] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 257.088787] ata1.01: hard resetting link
[ 257.408684] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.408688] ata1.02: hard resetting link
[ 257.728587] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 257.728591] ata1.03: hard resetting link
[ 258.048491] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 258.048495] ata1.04: hard resetting link
[ 258.368394] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 258.368397] ata1.05: hard resetting link
[ 258.688294] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 258.688298] ata1.06: hard resetting link
[ 259.008199] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 259.008295] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x11)
[ 259.008299] ata1.00: revalidation failed (errno=-5)
[ 259.008304] ata1.15: hard resetting link
[ 261.207356] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 261.207634] ata1.00: hard resetting link
[ 261.527434] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 261.527439] ata1.01: hard resetting link
[ 261.847337] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 261.847340] ata1.02: hard resetting link
[ 262.167238] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.167242] ata1.03: hard resetting link
[ 262.487142] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 262.487146] ata1.04: hard resetting link
[ 262.807046] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 262.807050] ata1.05: hard resetting link
[ 263.126946] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 263.126950] ata1.06: hard resetting link
[ 263.446852] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 263.449093] ata1.00: configured for UDMA/100
[ 263.451311] ata1.01: configured for UDMA/100
[ 263.556976] ata1.02: configured for UDMA/100
[ 263.658661] ata1.03: configured for UDMA/100
[ 263.658793] ata1.05: device is on DMA blacklist, disabling DMA
[ 263.658923] ata1.05: configured for PIO4
[ 263.659192] ata1: EH complete
[ 263.659218] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659229] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659232] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659245] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659260] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659267] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659270] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659281] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659295] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659303] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659305] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659317] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659330] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659337] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659340] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659351] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659365] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659372] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659375] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659386] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659399] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659407] sd 1:0:0:0: [sdb] Write Protect is off
[ 263.659409] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 263.659421] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659433] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659440] sd 1:1:0:0: [sdc] Write Protect is off
[ 263.659443] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 263.659454] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659467] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659474] sd 1:2:0:0: [sdd] Write Protect is off
[ 263.659477] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 263.659488] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659500] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 263.659508] sd 1:3:0:0: [sde] Write Protect is off
[ 263.659511] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 263.659522] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 263.659534] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 263.659541] sd 1:5:0:0: [sdf] Write Protect is off
[ 263.659544] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 263.659555] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 337.619074] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 337.619079] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 337.619083] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 337.619086] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 337.619089] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 337.619092] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 337.619095] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 337.619099] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 337.619103] ata1.15: irq_stat 0x01940090, PHY RDY changed
[ 337.619107] ata1: SError: { 10B8B }
[ 337.619111] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619116] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619122] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619127] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619132] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619137] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619142] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 337.619150] ata1.15: hard resetting link
[ 339.695540] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 339.947457] ata1.15: qc timeout (cmd 0xe4)
[ 339.947465] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 339.947469] ata1.15: PMP revalidation failed (errno=-5)
[ 339.947472] ata1.15: retrying hardreset in 5 secs
[ 344.949939] ata1.15: hard resetting link
[ 347.029314] ata1.15: SATA link down (SStatus 0 SControl 10)
[ 347.281232] ata1.15: qc timeout (cmd 0xe4)
[ 347.281239] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 347.281242] ata1.15: PMP revalidation failed (errno=-5)
[ 347.281246] ata1.15: retrying hardreset in 5 secs
[ 352.283714] ata1.15: hard resetting link
[ 356.250521] ata1.15: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[ 356.250717] ata1.00: hard resetting link
[ 356.570601] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 356.570605] ata1.01: hard resetting link
[ 356.890503] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 356.890507] ata1.02: hard resetting link
[ 357.210406] ata1.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.210411] ata1.03: hard resetting link
[ 357.530309] ata1.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 357.530313] ata1.04: hard resetting link
[ 357.850212] ata1.04: SATA link down (SStatus 0 SControl 310)
[ 357.850216] ata1.05: hard resetting link
[ 358.170112] ata1.05: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[ 358.170116] ata1.06: hard resetting link
[ 358.490020] ata1.06: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 358.492276] ata1.00: configured for UDMA/100
[ 358.494506] ata1.01: configured for UDMA/100
[ 358.595946] ata1.02: configured for UDMA/100
[ 358.705215] ata1.03: configured for UDMA/100
[ 358.705316] ata1.05: device is on DMA blacklist, disabling DMA
[ 358.705472] ata1.05: configured for PIO4
[ 358.705734] ata1: EH complete
[ 358.705759] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705773] sd 1:0:0:0: [sdb] Write Protect is off
[ 358.705776] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 358.705789] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705804] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705812] sd 1:1:0:0: [sdc] Write Protect is off
[ 358.705815] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 358.705827] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705841] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705849] sd 1:2:0:0: [sdd] Write Protect is off
[ 358.705852] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 358.705863] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705877] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705885] sd 1:3:0:0: [sde] Write Protect is off
[ 358.705888] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 358.705900] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705913] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 358.705921] sd 1:5:0:0: [sdf] Write Protect is off
[ 358.705924] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 358.705936] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705949] sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705957] sd 1:0:0:0: [sdb] Write Protect is off
[ 358.705960] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 358.705972] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.705985] sd 1:1:0:0: [sdc] 586072368 512-byte hardware sectors (300069 MB)
[ 358.705992] sd 1:1:0:0: [sdc] Write Protect is off
[ 358.705995] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 358.706007] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706020] sd 1:2:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
[ 358.706028] sd 1:2:0:0: [sdd] Write Protect is off
[ 358.706030] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 358.706042] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706055] sd 1:3:0:0: [sde] 586072368 512-byte hardware sectors (300069 MB)
[ 358.706063] sd 1:3:0:0: [sde] Write Protect is off
[ 358.706066] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 358.706077] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 358.706090] sd 1:5:0:0: [sdf] 640 512-byte hardware sectors (0 MB)
[ 358.706098] sd 1:5:0:0: [sdf] Write Protect is off
[ 358.706101] sd 1:5:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 358.706112] sd 1:5:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 404.739637] ata1.15: limiting speed to UDMA7:PIO5
[ 404.739644] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 404.739648] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 404.739651] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 404.739654] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 404.739657] ata1.04: failed to read SCR 1 (Emask=0x40)
[ 404.739660] ata1.05: failed to read SCR 1 (Emask=0x40)
[ 404.739663] ata1.06: failed to read SCR 1 (Emask=0x40)
[ 404.739667] ata1.15: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0xa frozen
[ 404.739671] ata1.15: irq_stat 0x01140010, PHY RDY changed
[ 404.739675] ata1: SError: { 10B8B }
[ 404.739679] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739685] ata1.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739690] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739695] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739700] ata1.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739705] ata1.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739710] ata1.06: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 404.739718] ata1.15: hard resetting link
[ 409.830262] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 410.082180] ata1.15: qc timeout (cmd 0xe4)
[ 410.082188] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 410.082191] ata1.15: PMP revalidation failed (errno=-5)
[ 410.082194] ata1.15: retrying hardreset in 5 secs
[ 415.084662] ata1.15: hard resetting link
[ 420.179121] ata1.15: SATA link down (SStatus 1 SControl 10)
[ 420.431039] ata1.15: qc timeout (cmd 0xe4)
[ 420.431047] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 420.431050] ata1.15: PMP revalidation failed (errno=-5)
[ 420.431054] ata1.15: retrying hardreset in 5 secs
[ 425.433523] ata1.15: hard resetting link
[ 435.438490] ata1.15: softreset failed (timeout)
[ 435.438494] ata1.15: hard resetting link
[ 445.443457] ata1.15: softreset failed (timeout)
[ 445.443463] ata1.15: hard resetting link
[ 480.432842] ata1.15: softreset failed (timeout)
[ 480.432850] ata1.15: hard resetting link
[ 485.431325] ata1.15: softreset failed (timeout)
[ 485.431329] ata1.15: failed to reset PMP, giving up
[ 485.431332] ata1.15: Port Multiplier detaching
[ 485.431340] ata1.00: disabled
[ 485.431343] ata1.01: disabled
[ 485.431346] ata1.02: disabled
[ 485.431348] ata1.03: disabled
[ 485.431350] ata1.05: disabled
[ 485.431354] ata1.00: disabled
[ 485.431360] ata1: hard resetting link
[ 495.436287] ata1: softreset failed (timeout)
[ 495.436290] ata1: hard resetting link
[ 505.441252] ata1: softreset failed (timeout)
[ 505.441255] ata1: hard resetting link
[ 540.430639] ata1: softreset failed (timeout)
[ 540.430647] ata1: limiting SATA link speed to 1.5 Gbps
[ 540.430650] ata1: hard resetting link
[ 545.525097] ata1: SATA link down (SStatus 1 SControl 10)
[ 545.525115] ata1: EH complete
[ 545.525125] ata1.00: detaching (SCSI 1:0:0:0)
[ 545.525299] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 545.525613] sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525617] sd 1:0:0:0: [sdb] Stopping disk
[ 545.525623] sd 1:0:0:0: [sdb] START_STOP FAILED
[ 545.525626] sd 1:0:0:0: [sdb] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525663] ata1.01: detaching (SCSI 1:1:0:0)
[ 545.525799] sd 1:1:0:0: [sdc] Synchronizing SCSI cache
[ 545.525944] sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
[ 545.525948] sd 1:1:0:0: [sdc] Stopping disk
[ 545.525970] sd 1:1:0:0: [sdc] START_STOP FAILED
[ 545.525972] sd 1:1:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
[ 545.526000] ata1.02: detaching (SCSI 1:2:0:0)
[ 545.526146] sd 1:2:0:0: [sdd] Synchronizing SCSI cache
[ 545.527048] sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527053] sd 1:2:0:0: [sdd] Stopping disk
[ 545.527071] sd 1:2:0:0: [sdd] START_STOP FAILED
[ 545.527074] sd 1:2:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527106] ata1.03: detaching (SCSI 1:3:0:0)
[ 545.527246] sd 1:3:0:0: [sde] Synchronizing SCSI cache
[ 545.527287] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527290] sd 1:3:0:0: [sde] Stopping disk
[ 545.527304] sd 1:3:0:0: [sde] START_STOP FAILED
[ 545.527306] sd 1:3:0:0: [sde] Result: hostbyte=0x04 driverbyte=0x00
[ 545.527333] ata1.05: detaching (SCSI 1:5:0:0)
[ 545.527451] sd 1:5:0:0: [sdf] Stopping disk
[ 545.527459] sd 1:5:0:0: [sdf] START_STOP FAILED
[ 545.527462] sd 1:5:0:0: [sdf] Result: hostbyte=0x04 driverbyte=0x00
[ 559.279656] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xa frozen
[ 559.279662] ata1: irq_stat 0x00a40080, device exchanged
[ 559.279673] ata1: hard resetting link
[ 563.427669] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 563.679583] ata1.15: qc timeout (cmd 0xe4)
[ 563.679589] ata1.15: failed to read PMP GSCR[0] (Emask=0x4)
[ 563.679593] ata1: failed to recover some devices, retrying in 5 secs
[ 568.682071] ata1: hard resetting link
[ 578.687033] ata1: softreset failed (timeout)
[ 578.687039] ata1: hard resetting link
[ 588.691996] ata1: softreset failed (timeout)
[ 588.691999] ata1: hard resetting link
[ 623.681382] ata1: softreset failed (timeout)
[ 623.681390] ata1: limiting SATA link speed to 1.5 Gbps
[ 623.681393] ata1: hard resetting link
[ 628.679864] ata1: softreset failed (timeout)
[ 628.679867] ata1: reset failed, giving up
[ 628.679878] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40d0000 action 0xa frozen t4
[ 628.679883] ata1: SError: { PHYRdyChg CommWake 10B8B DevExch }
[ 628.679892] ata1: hard resetting link
[ 638.684830] ata1: softreset failed (timeout)
[ 638.684836] ata1: hard resetting link
[ 648.689795] ata1: softreset failed (timeout)
[ 648.689801] ata1: hard resetting link
[ 683.679179] ata1: softreset failed (timeout)
[ 683.679186] ata1: limiting SATA link speed to 1.5 Gbps
[ 683.679189] ata1: hard resetting link
[ 688.677661] ata1: softreset failed (timeout)
[ 688.677664] ata1: reset failed, giving up
[ 688.677670] ata1: EH complete
[ 776.735711] ata2: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
[ 776.735717] ata2: irq_stat 0x00a40080, device exchanged
[ 776.735721] ata2: SError: { PHYRdyChg }
[ 776.735731] ata2: hard resetting link
[ 786.739911] ata2: softreset failed (timeout)
[ 786.739918] ata2: hard resetting link
[ 796.744875] ata2: softreset failed (timeout)
[ 796.744881] ata2: hard resetting link
[ 831.734261] ata2: softreset failed (timeout)
[ 831.734268] ata2: limiting SATA link speed to 1.5 Gbps
[ 831.734271] ata2: hard resetting link
[ 836.732744] ata2: softreset failed (timeout)
[ 836.732747] ata2: reset failed, giving up
[ 836.732753] ata2: EH complete
[ 1001.096027] ACPI: PCI interrupt for device 0000:00:0c.0 disabled
[ 1051.175431] sata_sil24 0000:00:0c.0: version 1.1
[ 1051.175576] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 1051.175960] PCI: Disallowing DAC for device 0000:00:0c.0
[ 1051.176552] scsi5 : sata_sil24
[ 1051.177500] scsi6 : sata_sil24
[ 1051.178092] scsi7 : sata_sil24
[ 1051.178658] scsi8 : sata_sil24
[ 1051.178696] ata5: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
[ 1051.178701] ata6: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
[ 1051.178705] ata7: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
[ 1051.178709] ata8: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
[ 1061.180649] ata5: softreset failed (timeout)
[ 1071.185612] ata5: softreset failed (timeout)
[ 1106.174999] ata5: softreset failed (timeout)
[ 1111.173481] ata5: softreset failed (timeout)
[ 1111.173484] ata5: reset failed, giving up
[ 1116.267939] ata6: SATA link down (SStatus 1 SControl 10)
[ 1118.347308] ata7: SATA link down (SStatus 0 SControl 0)
[ 1120.426676] ata8: SATA link down (SStatus 0 SControl 0)
[ 1190.130660] ACPI: PCI interrupt for device 0000:00:0c.0 disabled
[ 1201.390201] libata version 3.00 loaded.
[ 1201.391922] sata_sil24 0000:00:0c.0: version 1.1
[ 1201.391993] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 1201.392356] PCI: Disallowing DAC for device 0000:00:0c.0
[ 1201.393728] scsi9 : sata_sil24
[ 1201.394401] scsi10 : sata_sil24
[ 1201.394980] scsi11 : sata_sil24
[ 1201.395552] scsi12 : sata_sil24
[ 1201.395590] ata1: SATA max UDMA/100 host m128@0xfd900000 port 0xfd800000 irq 17
[ 1201.395594] ata2: SATA max UDMA/100 host m128@0xfd900000 port 0xfd802000 irq 17
[ 1201.395598] ata3: SATA max UDMA/100 host m128@0xfd900000 port 0xfd804000 irq 17
[ 1201.395603] ata4: SATA max UDMA/100 host m128@0xfd900000 port 0xfd806000 irq 17
[ 1211.399074] ata1: softreset failed (timeout)
[ 1221.404038] ata1: softreset failed (timeout)
[ 1256.393425] ata1: softreset failed (timeout)
[ 1261.391906] ata1: softreset failed (timeout)
[ 1261.391910] ata1: reset failed, giving up
[ 1266.486364] ata2: SATA link down (SStatus 1 SControl 10)
[ 1268.565732] ata3: SATA link down (SStatus 0 SControl 0)
[ 1270.645101] ata4: SATA link down (SStatus 0 SControl 0)
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-13 19:01 ` Andrew Ryder
@ 2008-01-14 0:35 ` Tejun Heo
2008-01-19 22:05 ` Andrew Ryder
0 siblings, 1 reply; 26+ messages in thread
From: Tejun Heo @ 2008-01-14 0:35 UTC (permalink / raw)
To: Andrew Ryder; +Cc: Gaston, Jason D, linux-ide
Andrew Ryder wrote:
> Tejun,
>
> I have completed some of the testing, things were working fine.. then
> something died. It will not even recognize the 4726 anymore. During book
> when the HBA does it scan nor in windows 2000 does anything work or be
> recognized.
>
> I will have a new eSATA cable this week sometime, maybe a pin got
> shmucked if lucky. I've attached the logs of the good and the gone dead.
Ah... definitely looks like a hardware problem. Hopefully cable is the
culprit. I wish the warranty of your port multiplier hasn't expired yet.
--
tejun
^ permalink raw reply [flat|nested] 26+ messages in thread
* RE: Sata 4726 Testing
2008-01-13 5:10 ` Tejun Heo
2008-01-13 19:01 ` Andrew Ryder
@ 2008-01-14 19:07 ` Gaston, Jason D
1 sibling, 0 replies; 26+ messages in thread
From: Gaston, Jason D @ 2008-01-14 19:07 UTC (permalink / raw)
To: Tejun Heo, Andrew Ryder; +Cc: linux-ide
>Gaston, for the initial detection failure messages when connected to
ICH
>AHCI, I don't really have much idea what's going on or how to fix it.
I
>suspect it's related to initial FISes from drives arriving
>asynchronously after hard resets but can't tell much without bus
>analyzer. Anyways, as EH can handle the case quickly enough, I guess
we
>can leave it at that for now. If you have ideas on what's going on or
>how to fix it, please lemme know.
>
>Thanks.
>
>--
>Tejun
Ok, thank you for all the work that you have done!
Jason
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-14 0:35 ` Tejun Heo
@ 2008-01-19 22:05 ` Andrew Ryder
2008-01-20 3:21 ` Tejun Heo
0 siblings, 1 reply; 26+ messages in thread
From: Andrew Ryder @ 2008-01-19 22:05 UTC (permalink / raw)
To: Tejun Heo; +Cc: Gaston, Jason D, linux-ide
Tejun,
I've got the hardware fixed and everything is working great. I have two
PMP's attached to the system both with 4 drives and have had no problems.
Thanks
Tejun Heo wrote:
> Andrew Ryder wrote:
>
>> Tejun,
>>
>> I have completed some of the testing, things were working fine.. then
>> something died. It will not even recognize the 4726 anymore. During book
>> when the HBA does it scan nor in windows 2000 does anything work or be
>> recognized.
>>
>> I will have a new eSATA cable this week sometime, maybe a pin got
>> shmucked if lucky. I've attached the logs of the good and the gone dead.
>>
>
> Ah... definitely looks like a hardware problem. Hopefully cable is the
> culprit. I wish the warranty of your port multiplier hasn't expired yet.
>
>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: Sata 4726 Testing
2008-01-19 22:05 ` Andrew Ryder
@ 2008-01-20 3:21 ` Tejun Heo
0 siblings, 0 replies; 26+ messages in thread
From: Tejun Heo @ 2008-01-20 3:21 UTC (permalink / raw)
To: Andrew Ryder; +Cc: Gaston, Jason D, linux-ide
Andrew Ryder wrote:
> Tejun,
>
> I've got the hardware fixed and everything is working great. I have two
> PMP's attached to the system both with 4 drives and have had no problems.
Good to hear. :-)
--
tejun
^ permalink raw reply [flat|nested] 26+ messages in thread
end of thread, other threads:[~2008-01-20 3:21 UTC | newest]
Thread overview: 26+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <4769A17A.8070806@shaw.ca>
[not found] ` <4769F974.2020905@gmail.com>
2007-12-20 22:23 ` Sata 4726 Testing Andrew Ryder
2007-12-22 13:53 ` Andrew Ryder
2008-01-07 16:12 ` Tejun Heo
2008-01-07 22:28 ` Andrew Ryder
2008-01-08 3:54 ` Tejun Heo
2008-01-08 8:00 ` Andrew Ryder
2008-01-09 5:45 ` Tejun Heo
2008-01-09 17:47 ` Andrew Ryder
2008-01-10 0:53 ` Tejun Heo
2008-01-10 1:58 ` Gaston, Jason D
2008-01-10 3:19 ` Tejun Heo
2008-01-10 16:24 ` Gaston, Jason D
2008-01-10 3:29 ` Tejun Heo
2008-01-09 23:00 ` Andrew Ryder
2008-01-10 4:20 ` Tejun Heo
2008-01-09 23:55 ` Andrew Ryder
2008-01-10 6:36 ` Tejun Heo
2008-01-11 1:19 ` Andrew Ryder
2008-01-11 7:49 ` Tejun Heo
2008-01-11 23:13 ` Andrew Ryder
2008-01-13 5:10 ` Tejun Heo
2008-01-13 19:01 ` Andrew Ryder
2008-01-14 0:35 ` Tejun Heo
2008-01-19 22:05 ` Andrew Ryder
2008-01-20 3:21 ` Tejun Heo
2008-01-14 19:07 ` Gaston, Jason D
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).