SonyDVD Writer errors on boot - gets disabled finally

SonyDVD Writer errors on boot - gets disabled finally

[Vaibhav Kalia]

[-- Attachment #1: Type: text/plain, Size: 2462 bytes --]

hi
i am facing this problem on my OpenSuse11, Ubuntu 8 installation on my
system (however the same system with windows xp works fine)
I am attaching a boot.msg and pasting the part of error here!
The hardware is:
One HDD IDE 80gb
One SATA 300GB
One SATA 250GB
Sony IDE DVD Writer

Sometimes it works fine.. but on an average out of 10 boots,7 times it
generates an exception.. and 3 times works fine...

Thanks & Best regards
Tony
-----------------------
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
<6>scsi0 : pata_atiixp
<6>scsi1 : pata_atiixp
<6>ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf400 irq 14
<6>ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf408 irq 15
<6>ata1.00: ATA-6: ST380011A, 8.01, max UDMA/100
<6>ata1.00: 156301488 sectors, multi 1: LBA48
<6>ata1.00: configured for UDMA/100
<6>ata2.00: ATAPI: SONY    DVD RW AW-G170A, 1.71, max UDMA/66
<4>ata2.00: Drive reports diagnostics failure. This may indicate a drive
<4>ata2.00: fault or invalid emulation. Contact drive vendor for information.
<4>ata2.00: limited to UDMA/33 due to 40-wire cable
<6>ata2.00: configured for UDMA/33
<5>scsi 0:0:0:0: Direct-Access     ATA      ST380011A        8.01 PQ: 0 ANSI: 5
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
<3>ata2.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
<4>         cdb 12 00 00 00 24 00 00 00  00 00 00 00 00 00 00 00
<4>         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
<3>ata2.00: status: { DRDY }
<6>ata2: soft resetting link
<4>ata2.00: qc timeout (cmd 0xa1)
<4>ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
<3>ata2.00: revalidation failed (errno=-5)
<4>ata2: failed to recover some devices, retrying in 5 secs
<4>ata2: port is slow to respond, please be patient (Status 0xd8)
<4>ata2: device not ready (errno=-16), forcing hardreset
<6>ata2: soft resetting link
<4>ata2.00: qc timeout (cmd 0xa1)
<4>ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
<3>ata2.00: revalidation failed (errno=-5)
<4>ata2: failed to recover some devices, retrying in 5 secs
<4>ata2: port is slow to respond, please be patient (Status 0xd8)
<4>ata2: device not ready (errno=-16), forcing hardreset
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/33
<6>ata2: EH complete
<5>scsi 1:0:0:0: CD-ROM            SONY     DVD RW AW-G170A  1.71 PQ: 0 ANSI: 5
-----------------------

[-- Attachment #2: boot.msg --]
[-- Type: application/octet-stream, Size: 36963 bytes --]

Inspecting /boot/System.map-2.6.25.5-1.1-default
Loaded 28387 symbols from /boot/System.map-2.6.25.5-1.1-default.
Symbols match kernel version 2.6.25.
No module symbols loaded - kernel modules not enabled.

klogd 1.4.1, log source = ksyslog started.
<5>Linux version 2.6.25.5-1.1-default (geeko@buildhost) (gcc version 4.3.1 20080507 (prerelease) [gcc-4_3-branch revision 135036] (SUSE Linux) ) #1 SMP 2008-06-07 01:55:22 +0200
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
<4> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000003bef0000 (usable)
<4> BIOS-e820: 000000003bef0000 - 000000003bef3000 (ACPI NVS)
<4> BIOS-e820: 000000003bef3000 - 000000003bf00000 (ACPI data)
<4> BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
<4> BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
<5>62MB HIGHMEM available.
<5>896MB LOWMEM available.
<6>Scan SMP from c0000000 for 1024 bytes.
<6>Scan SMP from c009fc00 for 1024 bytes.
<6>Scan SMP from c00f0000 for 65536 bytes.
<6>found SMP MP-table at [c00f6060] 000f6060
<7>Entering add_active_range(0, 0, 245488) 0 entries of 256 used
<4>Zone PFN ranges:
<4>  DMA             0 ->     4096
<4>  Normal       4096 ->   229376
<4>  HighMem    229376 ->   245488
<4>Movable zone start PFN for each node
<4>early_node_map[1] active PFN ranges
<4>    0:        0 ->   245488
<7>On node 0 totalpages: 245488
<7>  DMA zone: 32 pages used for memmap
<7>  DMA zone: 0 pages reserved
<7>  DMA zone: 4064 pages, LIFO batch:0
<7>  Normal zone: 1760 pages used for memmap
<7>  Normal zone: 223520 pages, LIFO batch:31
<7>  HighMem zone: 125 pages used for memmap
<7>  HighMem zone: 15987 pages, LIFO batch:3
<7>  Movable zone: 0 pages used for memmap
<6>DMI 2.3 present.
<6>Using APIC driver default
<4>ACPI: RSDP 000F7ED0, 0014 (r0 ATi   )
<4>ACPI: RSDT 3BEF3040, 0038 (r1 ATi    AWRDACPI 42302E31 AWRD        0)
<4>ACPI: FACP 3BEF30C0, 0074 (r1 ATi    AWRDACPI 42302E31 AWRD        0)
<4>ACPI: DSDT 3BEF3180, 3782 (r1 ATI    AWRDACPI     1000 MSFT  100000E)
<4>ACPI: FACS 3BEF0000, 0040
<4>ACPI: MCFG 3BEF6A80, 003C (r1 ATi    AWRDACPI 42302E31 AWRD        0)
<4>ACPI: APIC 3BEF6980, 0084 (r1 ATi    AWRDACPI 42302E31 AWRD        0)
<4>ACPI: SSDT 3BEF6B00, 015C (r1 ATI     Cpu0Ist     3000 INTL 20040311)
<4>ACPI: SSDT 3BEF6F90, 0275 (r1 ATI       CpuPm     3000 INTL 20040311)
<6>ATI board detected. Disabling timer routing over 8254.
<6>ACPI: PM-Timer IO Port: 0x4008
<7>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
<4>Processor #0 15:4 APIC version 20
<6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
<4>Processor #1 15:4 APIC version 20
<6>ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
<6>ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
<6>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
<6>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
<6>ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
<6>ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
<6>ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
<4>IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
<7>ACPI: IRQ0 used by override.
<7>ACPI: IRQ2 used by override.
<7>ACPI: IRQ9 used by override.
<4>Enabling APIC mode:  Flat.  Using 1 I/O APICs
<6>Using ACPI (MADT) for SMP configuration information
<4>Allocating PCI resources starting at 40000000 (gap: 3bf00000:a4100000)
<6>PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
<6>PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
<6>PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
<4>Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 243571
<5>Kernel command line: root=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 resume=/dev/sda4 splash=silent
<6>bootsplash: silent mode.
<7>mapped APIC to ffffb000 (fee00000)
<7>mapped IOAPIC to ffffa000 (fec00000)
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Initializing CPU#0
<4>PID hash table entries: 4096 (order: 12, 16384 bytes)
<4>Detected 3000.199 MHz processor.
<4>Console: colour VGA+ 80x25
<6>console [tty0] enabled
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Memory: 962764k/981952k available (1945k kernel code, 18544k reserved, 1629k data, 256k init, 64448k highmem)
<6>virtual kernel memory layout:
<4>    fixmap  : 0xffdf2000 - 0xfffff000   (2100 kB)
<4>    pkmap   : 0xff400000 - 0xff800000   (4096 kB)
<4>    vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB)
<4>    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
<4>      .init : 0xc0485000 - 0xc04c5000   ( 256 kB)
<4>      .data : 0xc02e64dd - 0xc047d96c   (1629 kB)
<4>      .text : 0xc0100000 - 0xc02e64dd   (1945 kB)
<6>Checking if this processor honours the WP bit even in supervisor mode...Ok.
<7>CPA: page pool initialized 1 of 1 pages preallocated
<4>Calibrating delay using timer specific routine.. 6008.10 BogoMIPS (lpj=12016219)
<6>Security Framework initialized
<6>AppArmor: AppArmor initialized <NULL>
<6>AppArmor: Registered secondary security module capability
<6>Capability LSM initialized as secondary
<4>Mount-cache hash table entries: 512
<6>CPU: Trace cache: 12K uops, L1 D cache: 16K
<6>CPU: L2 cache: 2048K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<6>CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
<6>CPU0: Thermal monitoring enabled
<4>Compat vDSO mapped to ffffe000.
<6>Checking 'hlt' instruction... OK.
<6>ACPI: Core revision 20070126
<6>ACPI: Checking initramfs for custom DSDT
<4>Parsing all Control Methods:
<4>Table [DSDT](id 0001) - 503 Objects with 43 Devices 133 Methods 21 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0002) - 5 Objects with 0 Devices 3 Methods 0 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0003) - 18 Objects with 0 Devices 3 Methods 0 Regions
<4> tbxface-0598 [00] tb_load_namespace     : ACPI Tables successfully acquired
<4>evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
<4>CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
<4>Booting processor 1/1 ip 4000
<6>Initializing CPU#1
<4>Calibrating delay using timer specific routine.. 6000.71 BogoMIPS (lpj=12001426)
<6>CPU: Trace cache: 12K uops, L1 D cache: 16K
<6>CPU: L2 cache: 2048K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#1.
<6>CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
<6>CPU1: Thermal monitoring enabled
<4>CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
<6>Total of 2 processors activated (12008.82 BogoMIPS).
<4>ENABLING IO-APIC IRQs
<6>..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
<6>checking TSC synchronization [CPU#0 -> CPU#1]: passed.
<6>Brought up 2 CPUs
<7>CPU0 attaching sched-domain:
<7> domain 0: span 00000003
<7>  groups: 00000001 00000002
<7>  domain 1: span 00000003
<7>   groups: 00000003
<7>CPU1 attaching sched-domain:
<7> domain 0: span 00000003
<7>  groups: 00000002 00000001
<7>  domain 1: span 00000003
<7>   groups: 00000003
<6>net_namespace: 548 bytes
<6>Booting paravirtualized kernel on bare hardware
<6>NET: Registered protocol family 16
<6>ACPI: bus type pci registered
<6>PCI: Using MMCONFIG for extended config space
<6>PCI: Using configuration type 1
<6>Setting up standard PCI resources
<4>evgpeblk-0956 [00] ev_create_gpe_block   : GPE 00 to 1F [_GPE] 4 regs on int 0x9
<4>evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 4 Wake, Enabled 0 Runtime GPEs in this block
<7>ACPI: EC: Look up EC in DSDT
<4>Completing Region/Field/Buffer/Package initialization:..............................................................
<4>Initialized 18/21 Regions 8/8 Fields 16/16 Buffers 20/24 Packages (535 nodes)
<4>Initializing Device/Processor/Thermal objects by executing _INI methods:...
<4>Executed 3 _INI methods requiring 1 _STA executions (examined 50 objects)
<6>ACPI: Interpreter enabled
<6>ACPI: (supports S0 S1 S4 S5)
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: PCI Root Bridge [PCI0] (0000:00)
<6>PCI: Transparent bridge - 0000:00:14.4
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
<6>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11)
<6>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11)
<6>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11)
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<6>pnp: PnP ACPI init
<6>ACPI: bus type pnp registered
<4> 00:0c: mem resource (0xe0000000-0xefffffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
<4> 00:0d: mem resource (0xffff0000-0xffffffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
<4> 00:0d: mem resource (0xfec00000-0xfec00fff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
<4> 00:0d: mem resource (0xfee00000-0xfee00fff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
<4> 00:0d: mem resource (0xfff80000-0xfffeffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
<6>pnp: PnP ACPI: found 14 devices
<6>ACPI: ACPI bus type pnp unregistered
<6>PnPBIOS: Disabled by ACPI PNP
<6>PCI: Using ACPI for IRQ routing
<6>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
<3>PCI: Cannot allocate resource region 3 of device 0000:00:00.0
<6>AppArmor: AppArmor Filesystem Enabled 
<4>ACPI: RTC can wake from S4
<6>system 00:01: ioport range 0x228-0x22f has been reserved
<6>system 00:01: ioport range 0x40b-0x40b has been reserved
<6>system 00:01: ioport range 0x4d6-0x4d6 has been reserved
<6>system 00:01: ioport range 0xc00-0xc01 has been reserved
<6>system 00:01: ioport range 0xc14-0xc14 has been reserved
<6>system 00:01: ioport range 0xc50-0xc52 has been reserved
<6>system 00:01: ioport range 0xc6c-0xc6d has been reserved
<6>system 00:01: ioport range 0xc6f-0xc6f has been reserved
<6>system 00:01: ioport range 0xcd4-0xcdf has been reserved
<6>system 00:01: ioport range 0x4000-0x40fe has been reserved
<6>system 00:01: ioport range 0x4210-0x4217 has been reserved
<6>system 00:06: ioport range 0x4d0-0x4d1 has been reserved
<6>system 00:06: ioport range 0x800-0x87f has been reserved
<6>system 00:06: ioport range 0x880-0x88f has been reserved
<6>system 00:0d: iomem range 0xf0000-0xf3fff could not be reserved
<6>system 00:0d: iomem range 0xf4000-0xf7fff could not be reserved
<6>system 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
<6>system 00:0d: iomem range 0xfc000-0xfffff could not be reserved
<6>system 00:0d: iomem range 0x3bf00000-0x3bffffff has been reserved
<6>system 00:0d: iomem range 0x3bef0000-0x3befffff could not be reserved
<6>system 00:0d: iomem range 0x0-0x9ffff could not be reserved
<6>system 00:0d: iomem range 0x100000-0x3beeffff could not be reserved
<6>PCI: Bridge: 0000:00:01.0
<6>  IO window: e000-efff
<6>  MEM window: 0xfde00000-0xfdefffff
<6>  PREFETCH window: 0x00000000d8000000-0x00000000dfffffff
<6>PCI: Bridge: 0000:00:14.4
<6>  IO window: d000-dfff
<6>  MEM window: 0xfdd00000-0xfddfffff
<6>  PREFETCH window: 0x00000000fdc00000-0x00000000fdcfffff
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP reno registered
<6>Unpacking initramfs... done
<6>Freeing initrd memory: 5529k freed
<6>Machine check exception polling timer started.
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(1215845635.720:1): initialized
<4>highmem bounce pool size: 64 pages
<4>Total HugeTLB memory allocated, 0
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<4>pci 0000:00:00.0: MSI quirk detected; MSI disabled
<7>pci 0000:01:05.0: Boot video device
<6>isapnp: Scanning for PnP cards...
<7>Switched to high resolution mode on CPU 1
<7>Switched to high resolution mode on CPU 0
<6>isapnp: No Plug & Play device found
<6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
<6>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<6>PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
<6>serio: i8042 KBD port at 0x60,0x64 irq 1
<6>serio: i8042 AUX port at 0x60,0x64 irq 12
<6>mice: PS/2 mouse device common for all mice
<6>input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
<6>input: PC Speaker as /devices/platform/pcspkr/input/input1
<6>input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input2
<6>cpuidle: using governor ladder
<6>cpuidle: using governor menu
<6>NET: Registered protocol family 1
<4>Using IPI No-Shortcut mode
<4>registered taskstats version 1
<6>Freeing unused kernel memory: 256k freed
<6>Write protecting the kernel read-only data: 1440k
<6>ACPI: ACPI0007:00 is registered as cooling_device0
<6>ACPI: Processor [CPU0] (supports 8 throttling states)
<4>ACPI: SSDT 3BEF6F00, 0087 (r1 ATI     Cpu1Ist     3000 INTL 20040311)
<4>Parsing all Control Methods:
<4>Table [SSDT](id 004A) - 3 Objects with 0 Devices 3 Methods 0 Regions
<6>ACPI: ACPI0007:01 is registered as cooling_device1
<6>ACPI: Processor [CPU1] (supports 8 throttling states)
<6>ACPI: LNXTHERM:01 is registered as thermal_zone0
<6>ACPI: Thermal Zone [THRM] (40 C)
<6>ACPI: PNP0C0B:00 is registered as cooling_device2
<6>ACPI: Fan [FAN] (on)
<6>No dock devices found.
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
<6>scsi0 : pata_atiixp
<6>scsi1 : pata_atiixp
<6>ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf400 irq 14
<6>ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf408 irq 15
<6>ata1.00: ATA-6: ST380011A, 8.01, max UDMA/100
<6>ata1.00: 156301488 sectors, multi 1: LBA48 
<6>ata1.00: configured for UDMA/100
<6>ata2.00: ATAPI: SONY    DVD RW AW-G170A, 1.71, max UDMA/66
<4>ata2.00: Drive reports diagnostics failure. This may indicate a drive
<4>ata2.00: fault or invalid emulation. Contact drive vendor for information.
<4>ata2.00: limited to UDMA/33 due to 40-wire cable
<6>ata2.00: configured for UDMA/33
<5>scsi 0:0:0:0: Direct-Access     ATA      ST380011A        8.01 PQ: 0 ANSI: 5
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
<3>ata2.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
<4>         cdb 12 00 00 00 24 00 00 00  00 00 00 00 00 00 00 00
<4>         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
<3>ata2.00: status: { DRDY }
<6>ata2: soft resetting link
<4>ata2.00: qc timeout (cmd 0xa1)
<4>ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
<3>ata2.00: revalidation failed (errno=-5)
<4>ata2: failed to recover some devices, retrying in 5 secs
<4>ata2: port is slow to respond, please be patient (Status 0xd8)
<4>ata2: device not ready (errno=-16), forcing hardreset
<6>ata2: soft resetting link
<4>ata2.00: qc timeout (cmd 0xa1)
<4>ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
<3>ata2.00: revalidation failed (errno=-5)
<4>ata2: failed to recover some devices, retrying in 5 secs
<4>ata2: port is slow to respond, please be patient (Status 0xd8)
<4>ata2: device not ready (errno=-16), forcing hardreset
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/33
<6>ata2: EH complete
<5>scsi 1:0:0:0: CD-ROM            SONY     DVD RW AW-G170A  1.71 PQ: 0 ANSI: 5
<6>BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<4>Driver 'sd' needs updating - please use bus_type methods
<5>sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<5>sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sda:<6>usbcore: registered new device driver usb
<7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
<6>ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
<6>ohci_hcd 0000:00:13.0: OHCI Host Controller
<6>ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
<6>ohci_hcd 0000:00:13.0: irq 19, io mem 0xfe02d000
<4> sda1 sda2 < sda5 > sda3 sda4
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 4 ports detected
<5>sd 0:0:0:0: [sda] Attached SCSI disk
<6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
<6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: OHCI Host Controller
<6>usb usb1: Manufacturer: Linux 2.6.25.5-1.1-default ohci_hcd
<6>usb usb1: SerialNumber: 0000:00:13.0
<6>ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
<6>ehci_hcd 0000:00:13.2: EHCI Host Controller
<6>ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
<6>ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe02b000
<6>ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 8 ports detected
<6>usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
<6>usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb2: Product: EHCI Host Controller
<6>usb usb2: Manufacturer: Linux 2.6.25.5-1.1-default ehci_hcd
<6>usb usb2: SerialNumber: 0000:00:13.2
<6>ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
<6>ohci_hcd 0000:00:13.1: OHCI Host Controller
<6>ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
<6>ohci_hcd 0000:00:13.1: irq 19, io mem 0xfe02c000
<6>usb usb3: configuration #1 chosen from 1 choice
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 4 ports detected
<6>usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
<6>usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb3: Product: OHCI Host Controller
<6>usb usb3: Manufacturer: Linux 2.6.25.5-1.1-default ohci_hcd
<6>usb usb3: SerialNumber: 0000:00:13.1
<6>PM: Starting manual resume from disk
<6>usb 2-3: new high speed USB device using ehci_hcd and address 2
<6>usb 2-3: configuration #1 chosen from 1 choice
<6>usb 2-3: New USB device found, idVendor=07d1, idProduct=3c03
<6>usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 2-3: Product: 802.11 bg WLAN
<6>usb 2-3: Manufacturer: Ralink
<3>hub 2-0:1.0: unable to enumerate USB device on port 4
<3>hub 2-0:1.0: unable to enumerate USB device on port 5
<6>usb 3-2: new full speed USB device using ohci_hcd and address 2
<6>usb 3-2: configuration #1 chosen from 1 choice
<6>hub 3-2:1.0: USB hub found
<6>hub 3-2:1.0: 4 ports detected
<6>usb 3-2: New USB device found, idVendor=03eb, idProduct=0902
<6>usb 3-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>usb 1-3: new full speed USB device using ohci_hcd and address 2
<6>usb 1-3: configuration #1 chosen from 1 choice
<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>scsi 1:0:0:0: Attached scsi generic sg1 type 5
<6>parport_pc 00:09: reported by Plug and Play ACPI
<6>parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
<6>Linux agpgart interface v0.103
<6>Uniform Multi-Platform E-IDE driver
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
<4>Driver 'sr' needs updating - please use bus_type methods
<4>sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
<6>Uniform CD-ROM driver Revision: 3.20
<7>sr 1:0:0:0: Attached scsi CD-ROM sr0
<6>rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
<6>rtc0: alarms up to one month
<6>ppdev: user-space parallel port driver
<6>input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
<6>ACPI: Power Button (FF) [PWRF]
<6>input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
<6>8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
<3>8139cp 0000:02:02.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
<3>8139cp 0000:02:02.0: Try the "8139too" driver instead.
<6>ACPI: Power Button (CM) [PWRB]
<6>shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
<6>piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
<4>ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region SM00 [0xb00-0xb07]
<6>ACPI: Device needs an ACPI driver
<6>ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 17
<6>ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17]  MMIO=[fddfe000-fddfe7ff]  Max Packet=[2048]  IR/IT contexts=[8/8]
<7>sata_sil 0000:00:11.0: version 2.3
<6>ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 23
<6>scsi2 : sata_sil
<6>scsi3 : sata_sil
<6>ata3: SATA max UDMA/100 mmio m512@0xfe02f000 tf 0xfe02f080 irq 23
<6>ata4: SATA max UDMA/100 mmio m512@0xfe02f000 tf 0xfe02f0c0 irq 23
<6>usb 1-3: New USB device found, idVendor=040a, idProduct=0000
<6>usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>usb 3-2.2: new full speed USB device using ohci_hcd and address 3
<6>ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
<6>ata3.00: ATA-8: Hitachi HDP725025GLA380, GM2OA52A, max UDMA/133
<6>ata3.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 0/32)
<6>ata3.00: configured for UDMA/100
<7>phy0: Selected rate control algorithm 'pid'
<6>usb 3-2.2: configuration #1 chosen from 1 choice
<6>usb 3-2.2: New USB device found, idVendor=0a12, idProduct=0001
<6>usb 3-2.2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>usbcore: registered new interface driver rt73usb
<6>Bluetooth: Core ver 2.11
<6>NET: Registered protocol family 31
<6>Bluetooth: HCI device and connection manager initialized
<6>Bluetooth: HCI socket layer initialized
<6>ata4: SATA link down (SStatus 0 SControl 310)
<5>scsi 2:0:0:0: Direct-Access     ATA      Hitachi HDP72502 GM2O PQ: 0 ANSI: 5
<5>sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
<5>sd 2:0:0:0: [sdb] Write Protect is off
<7>sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<5>sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
<5>sd 2:0:0:0: [sdb] Write Protect is off
<7>sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sdb: sdb1
<5>sd 2:0:0:0: [sdb] Attached SCSI disk
<5>sd 2:0:0:0: Attached scsi generic sg2 type 0
<6>ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 22
<6>scsi4 : sata_sil
<6>scsi5 : sata_sil
<6>ata5: SATA max UDMA/100 mmio m512@0xfe02e000 tf 0xfe02e080 irq 22
<6>ata6: SATA max UDMA/100 mmio m512@0xfe02e000 tf 0xfe02e0c0 irq 22
<6>Bluetooth: Generic Bluetooth USB driver ver 0.1
<6>usbcore: registered new interface driver btusb
<6>Bluetooth: HCI USB driver ver 2.9
<6>usbcore: registered new interface driver hci_usb
<7>ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00601d0000008517]
<6>ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
<6>ata5.00: ATA-7: ST3320820AS, 3.AAC, max UDMA/133
<6>ata5.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 0/32)
<6>ata5.00: configured for UDMA/100
<6>Bluetooth: L2CAP ver 2.9
<6>Bluetooth: L2CAP socket layer initialized
<6>Bluetooth: RFCOMM socket layer initialized
<6>Bluetooth: RFCOMM TTY layer initialized
<6>Bluetooth: RFCOMM ver 1.8
<6>ata6: SATA link down (SStatus 0 SControl 310)
<5>scsi 4:0:0:0: Direct-Access     ATA      ST3320820AS      3.AA PQ: 0 ANSI: 5
<5>sd 4:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
<5>sd 4:0:0:0: [sdc] Write Protect is off
<7>sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
<5>sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<5>sd 4:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
<5>sd 4:0:0:0: [sdc] Write Protect is off
<7>sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
<5>sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sdc: sdc1 < sdc5 >
<5>sd 4:0:0:0: [sdc] Attached SCSI disk
<5>sd 4:0:0:0: Attached scsi generic sg3 type 0
<6>ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 16 (level, low) -> IRQ 16
<6>Adding 72284k swap on /dev/sda4.  Priority:-1 extents:1 across:72284k
<6>device-mapper: uevent: version 1.0.3
<6>device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
<6>loop: module loaded
<4>fuse init (API version 7.9)
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.

Boot logging started on /dev/tty1(/dev/console) at Sat Jul 12 06:53:56 2008

Creating device nodes with udev
Trying manual resume from /dev/sda4
Invoking userspace resume from /dev/sda4
boot/82-resume.userspace.sh: line 48: /proc/splash: No such file or directory
resume: libgcrypt version: 1.4.0
Trying manual resume from /dev/sda4
Invoking in-kernel resume from /dev/sda4
Waiting for device /dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 to appear:  ok
fsck 1.40.8 (13-Mar-2008)
[/sbin/fsck.ext2 (1) -- /] fsck.ext2 -a -C0 /dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 
/: clean, 80893/513072 files, 952877/2048287 blocks
fsck succeeded. Mounting root device read-write.
Mounting root /dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3

Boot logging started on /dev/tty1(/dev/console (deleted)) at Sat Jul 12 12:25:37 2008

done
Starting udevd: done
Loading required kernel modules
doneActivating swap-devices in /etc/fstab...
donemount: according to mtab, /dev/sda3 is already mounted on /

Setting up the hardware clockdone
Activating device mapper...
done
Checking file systems...
fsck 1.40.8 (13-Mar-2008)
donedone
Mounting local file systems...
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
udev on /dev type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/sda1 on /windows/C type vfat (rw,noexec,nosuid,nodev,gid=100,umask=0002,utf8=true)
/dev/sda5 on /windows/D type vfat (rw,noexec,nosuid,nodev,gid=100,umask=0002,utf8=true)
doneFuse filesystem already availabledone
Mounting fuse control filesystemdone
Configuring serial ports...
/dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A
Configured serial ports
doneSetting current sysctl status from /etc/sysctl.conf
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.conf.all.rp_filter = 1
fs.inotify.max_user_watches = 65536
net.ipv4.conf.default.promote_secondaries = 1
net.ipv4.conf.all.promote_secondaries = 1
done
Mounting securityfs on /sys/kernel/security done
Activating remaining swap-devices in /etc/fstab...
doneLoading AppArmor profiles <notice>killproc: kill(584,29)
Creating /var/log/boot.msg
doneEnabling syn flood protectiondone
Disabling IP forwardingdone
done
Turning quota on
Checking quotas. This may take some time.
done
done
Setting up hostname 'vaibhav'done
Setting up loopback interface     lo        
    lo        IP address: 127.0.0.1/8   
              IP address: 127.0.0.2/8   
done
System Boot Control: The system has been set up
System Boot Control: Running /etc/init.d/boot.local
done<notice>killproc: kill(584,3)

INIT: 
Boot logging started on /dev/tty1(/dev/console) at Sat Jul 12 06:55:46 2008

Master Resource Control: previous runlevel: N, switching to runlevel: 3
<notice>startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/sbin/resmgrd ]
<notice>startproc: execve (/sbin/acpid) [ /sbin/acpid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/sbin/acpid ]
Starting resource managerdone
acpid: starting up


Starting acpid done
Starting java.binfmt_misc done
acpid: 0 rules loaded


Initializing random number generatordone
Starting D-Bus daemonChecking/updating CPU microcode done
done
<notice>startproc: execve (/usr/sbin/console-kit-daemon) [ /usr/sbin/console-kit-daemon ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/usr/sbin/console-kit-daemon ]
Starting ConsoleKitdone
Loading CPUFreq modulesEntering runlevel: 3


 CONSOLE=/dev/consoleEntering runlevel: 3


 CONSOLE=/dev/consoledone
Starting HAL daemonLoading keymap i386/qwerty/us.map.gz
doneLoading compose table latin1.adddone
Start Unicode mode
doneacpid: client connected from 2215[103:104]


acpid: 1 client rule loaded


done
<notice>startproc: execve (/usr/sbin/NetworkManager) [ /usr/sbin/NetworkManager ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/usr/sbin/NetworkManager ]
Starting the NetworkManagerdone
NetworkManager: <info>  starting...


NetworkManager: <info>  wlan0: Device is fully-supported using driver 'rt73usb'.


NetworkManager: <info>  wlan0: driver supports SSID scans (scan_capa 0x01).


NetworkManager: <info>  Found new wireless (802.11) device 'wlan0'.


NetworkManager: <info>  (wlan0): exported as /org/freedesktop/Hal/devices/net_00_15_e9_a4_c1_54


NetworkManager: <info>  Trying to start the supplicant...


NetworkManager: <info>  Trying to start the system settings daemon...


Starting syslog services<notice>startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/sbin/syslog-ng ]
<notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/sbin/klogd ]
done
<notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/sbin/portmap ]
Starting RPC portmap daemondone
<notice>startproc: execve (/sbin/auditd) [ /sbin/auditd -s disable ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/sbin/auditd ]
Starting auditd done
<notice>startproc: execve (/usr/sbin/avahi-daemon) [ /usr/sbin/avahi-daemon -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/usr/sbin/avahi-daemon ]
Starting Avahi daemondone
<notice>startproc: execve (/usr/sbin/avahi-dnsconfd) [ /usr/sbin/avahi-dnsconfd -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/usr/sbin/avahi-dnsconfd ]
<notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/usr/sbin/nscd ]
Starting Avahi DNS Configuration daemondone
<notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/usr/sbin/cupsd ]
Starting Name Service Cache Daemondone
Starting cupsddone
<notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/usr/sbin/sshd ]
Starting SSH daemondone
<notice>startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -f /var/run/acpid.socket -v 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=3 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ]
Starting powersaved: done
Starting mail service (Postfix)done
<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext2 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST380011A_5JVK1S4G-part3 _=/sbin/startproc DAEMON=/usr/sbin/cron ]
Starting CRON daemondone
done
Master Resource Control: runlevel 3 has been reached
Skipped services in runlevel 3: splash
<notice>killproc: kill(1749,3)

Re: SonyDVD Writer errors on boot - gets disabled finally

[Tejun Heo]

Vaibhav Kalia wrote:
> hi
> i am facing this problem on my OpenSuse11, Ubuntu 8 installation on my
> system (however the same system with windows xp works fine)
> I am attaching a boot.msg and pasting the part of error here!
> The hardware is:
> One HDD IDE 80gb
> One SATA 300GB
> One SATA 250GB
> Sony IDE DVD Writer
> 
> Sometimes it works fine.. but on an average out of 10 boots,7 times it
> generates an exception.. and 3 times works fine...

Does kernel parameter "libata.force=2.00:udma25" makes any difference?
If it doesn't work, how about "libata.force=2.00:pio4"?

-- 
tejun