From: Harri Olin <harri.olin@gmail.com>
To: Artem Bokhan <aptem@ngs.ru>
Cc: linux-ide@vger.kernel.org, tj@kernel.org, liml@rtr.ca
Subject: Re: sata_mv, io stucks
Date: Thu, 23 Oct 2008 16:31:06 +0300 [thread overview]
Message-ID: <49007C9A.7000103@gmail.com> (raw)
In-Reply-To: <48F88449.1000704@ngs.ru>
Artem Bokhan wrote:
> I try to simulate random reads with "sysbench --test=fileio
> --num-threads=16 --max-requests=9999999 --max-time=60 --init-rng=on
> --file-num=16 --file-fsync-freq=0 --file-test-mode=rndrd
> --file-total-size=30G run"
>
> Two marvell controllers, 16 disks, software raid10, IO stucks on
> different disks, kernel 2.6.26.5.
> With default ubuntu's 8.04 2.6.24 kernel the problem can not be repeated
I have the same problem with recent kernels with updated sata_mv driver.
First IO stops for a while and afer EH runs, everything works again for
a while. Happens on 3 different computers using WD5000ABYS, WD5000YS and
WD7500AYYS hard disks, RAID5 and 6 configurations using Linux MD.
Stalls seem to happen only on controller ports 0-3, ports 4-7 work
without problems.
Contoller is Supermicro AOC-SAT2-MV8, connected to 133MHz PCI-X slot on
one computer, 66MHz 64bit PCI slot on the second machine and to normal
32bit PCI slot on third computer.
http://www.supermicro.com/products/accessories/addon/AoC-SAT2-MV8.cfm
At the moment I don't have disks connected to failing ports, but if
needed, I can test patches.
Oct 10 18:56:17 mizar kernel: ata10.00: exception Emask 0x0 SAct 0x0
SErr 0x0 action 0x6 frozen
Oct 10 18:56:17 mizar kernel: ata10.00: cmd
35/00:08:3f:52:54/00:00:57:00:00/e0 tag 0 dma 4096 out
Oct 10 18:56:17 mizar kernel: res
40/00:ff:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
Oct 10 18:56:17 mizar kernel: ata10.00: status: { DRDY }
Oct 10 18:56:17 mizar kernel: ata10: hard resetting link
Oct 10 18:56:17 mizar kernel: ata10: SATA link up 1.5 Gbps (SStatus 113
SControl 310)
Oct 10 18:56:17 mizar kernel: ata10.00: max_sectors limited to 256 for NCQ
Oct 10 18:56:17 mizar kernel: ata10.00: max_sectors limited to 256 for NCQ
Oct 10 18:56:17 mizar kernel: ata10.00: configured for UDMA/33
Oct 10 18:56:17 mizar kernel: ata10: EH complete
Oct 10 18:56:17 mizar kernel: sd 9:0:0:0: [sdg] 1465149168 512-byte
hardware sectors (750156 MB)
Oct 10 18:56:17 mizar kernel: sd 9:0:0:0: [sdg] Write Protect is off
Oct 10 18:56:17 mizar kernel: sd 9:0:0:0: [sdg] Mode Sense: 00 3a 00 00
Oct 10 18:56:17 mizar kernel: sd 9:0:0:0: [sdg] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Oct 10 19:34:58 mizar kernel: ata10.00: exception Emask 0x0 SAct 0x0
SErr 0x0 action 0x6 frozen
Oct 10 19:34:58 mizar kernel: ata10.00: cmd
35/00:08:3f:52:54/00:00:57:00:00/e0 tag 0 dma 4096 out
Oct 10 19:34:58 mizar kernel: res
40/00:ff:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
Oct 10 19:34:58 mizar kernel: ata10.00: status: { DRDY }
Oct 10 19:34:58 mizar kernel: ata10: hard resetting link
Oct 10 19:34:58 mizar kernel: ata10: SATA link up 1.5 Gbps (SStatus 113
SControl 310)
Oct 10 19:34:58 mizar kernel: ata10.00: max_sectors limited to 256 for NCQ
Oct 10 19:34:58 mizar kernel: ata10.00: max_sectors limited to 256 for NCQ
Oct 10 19:34:58 mizar kernel: ata10.00: configured for UDMA/33
Oct 10 19:34:58 mizar kernel: ata10: EH complete
Oct 10 19:34:58 mizar kernel: sd 9:0:0:0: [sdg] 1465149168 512-byte
hardware sectors (750156 MB)
Oct 10 19:34:58 mizar kernel: sd 9:0:0:0: [sdg] Write Protect is off
Oct 10 19:34:58 mizar kernel: sd 9:0:0:0: [sdg] Mode Sense: 00 3a 00 00
Oct 10 19:34:58 mizar kernel: sd 9:0:0:0: [sdg] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Oct 10 19:37:05 mizar kernel: ata10.00: exception Emask 0x0 SAct 0x0
SErr 0x0 action 0x6 frozen
Oct 10 19:37:05 mizar kernel: ata10.00: cmd
35/00:08:3f:52:54/00:00:57:00:00/e0 tag 0 dma 4096 out
Oct 10 19:37:05 mizar kernel: res
40/00:ff:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout)
Oct 10 19:37:05 mizar kernel: ata10.00: status: { DRDY }
Oct 10 19:37:05 mizar kernel: ata10: hard resetting link
Oct 10 19:37:06 mizar kernel: ata10: SATA link up 1.5 Gbps (SStatus 113
SControl 310)
Oct 10 19:37:06 mizar kernel: ata10.00: max_sectors limited to 256 for NCQ
Oct 10 19:37:06 mizar kernel: ata10.00: max_sectors limited to 256 for NCQ
Oct 10 19:37:06 mizar kernel: ata10.00: configured for UDMA/33
Oct 10 19:37:06 mizar kernel: ata10: EH complete
Oct 10 19:37:06 mizar kernel: sd 9:0:0:0: [sdg] 1465149168 512-byte
hardware sectors (750156 MB)
Oct 10 19:37:06 mizar kernel: sd 9:0:0:0: [sdg] Write Protect is off
Oct 10 19:37:06 mizar kernel: sd 9:0:0:0: [sdg] Mode Sense: 00 3a 00 00
Oct 10 19:37:06 mizar kernel: sd 9:0:0:0: [sdg] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: exception Emask 0x0 SAct 0xf
SErr 0x0 action 0x6 frozen
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: cmd
60/40:00:7f:a1:e2/00:00:28:00:00/40 tag 0 ncq 32768 in
Sep 26 15:47:14 mvsrv02 kernel: res
40/00:00:09:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: status: { DRDY }
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: cmd
60/40:08:3f:a1:e2/00:00:28:00:00/40 tag 1 ncq 32768 in
Sep 26 15:47:14 mvsrv02 kernel: res
40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: status: { DRDY }
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: cmd
60/40:10:3f:a2:e2/00:00:28:00:00/40 tag 2 ncq 32768 in
Sep 26 15:47:14 mvsrv02 kernel: res
40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: status: { DRDY }
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: cmd
60/c0:18:7f:a2:e2/00:00:28:00:00/40 tag 3 ncq 98304 in
Sep 26 15:47:14 mvsrv02 kernel: res
40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: status: { DRDY }
Sep 26 15:47:14 mvsrv02 kernel: ata5: hard resetting link
Sep 26 15:47:14 mvsrv02 kernel: ata5: SATA link up 3.0 Gbps (SStatus 123
SControl 300)
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: max_sectors limited to 256 for NCQ
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: max_sectors limited to 256 for NCQ
Sep 26 15:47:14 mvsrv02 kernel: ata5.00: configured for UDMA/133
Sep 26 15:47:14 mvsrv02 kernel: ata5: EH complete
Sep 26 15:47:14 mvsrv02 kernel: sd 4:0:0:0: [sdb] 976773168 512-byte
hardware sectors (500108 MB)
Sep 26 15:47:14 mvsrv02 kernel: sd 4:0:0:0: [sdb] Write Protect is off
Sep 26 15:47:14 mvsrv02 kernel: sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Sep 26 15:47:14 mvsrv02 kernel: sd 4:0:0:0: [sdb] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
1st comuter: 133MHz PCI-X slot
03:01.0 SCSI storage controller: Marvell Technology Group Ltd.
MV88SX6081 8-port SATA II PCI-X Controller (rev 09)
Subsystem: Marvell Technology Group Ltd. Unknown device 11ab
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B+ DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at d8800000 (64-bit, non-prefetchable) [size=1M]
Region 2: I/O ports at 3000 [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=4
Status: Dev=03:01.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512 DMOST=4 DMCRS=8 RSCEM- 266MHz- 533MHz-
Kernel driver in use: sata_mv
2nd: 66MHz 64bit PCI
02:01.0 SCSI storage controller: Marvell Technology Group Ltd.
MV88SX6081 8-port SATA II PCI-X Controller (rev 09)
Subsystem: Marvell Technology Group Ltd. Unknown device 11ab
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 24
Region 0: Memory at f2800000 (64-bit, non-prefetchable) [size=1M]
Region 2: I/O ports at c000 [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=4
Status: Dev=02:01.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512 DMOST=4 DMCRS=8 RSCEM- 266MHz- 533MHz-
3rd computer: 32bit 33MHz PCI
00:0a.0 SCSI storage controller: Marvell Technology Group Ltd.
MV88SX6081 8-port SATA II PCI-X Controller (rev 09)
Subsystem: Marvell Technology Group Ltd. Unknown device 11ab
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at cfe00000 (64-bit, non-prefetchable) [size=1M]
Region 2: I/O ports at dc00 [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=4
Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512 DMOST=4 DMCRS=8 RSCEM- 266MHz- 533MHz-
--
Harri.
next prev parent reply other threads:[~2008-10-23 13:40 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-10-17 12:25 sata_mv, io stucks Artem Bokhan
2008-10-23 8:53 ` Artem Bokhan
2008-10-23 16:07 ` Mark Lord
2008-11-15 15:18 ` Harri Olin
2008-11-15 21:35 ` Mark Lord
2008-11-15 23:41 ` Harri Olin
2008-11-15 23:44 ` Justin Piszcz
2008-11-15 23:47 ` Harri Olin
2008-11-15 23:52 ` Justin Piszcz
2008-11-16 4:43 ` Mark Lord
2008-11-16 4:59 ` Mark Lord
2008-11-16 9:13 ` Justin Piszcz
2008-11-17 5:22 ` Mark Lord
2008-11-17 14:10 ` Bokhan Artem
2008-11-16 12:35 ` Harri Olin
2008-11-16 17:32 ` Harri Olin
2008-10-23 13:31 ` Harri Olin [this message]
2008-10-23 16:32 ` Bokhan Artem
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=49007C9A.7000103@gmail.com \
--to=harri.olin@gmail.com \
--cc=aptem@ngs.ru \
--cc=liml@rtr.ca \
--cc=linux-ide@vger.kernel.org \
--cc=tj@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).