From: Roman Valls <rvalls@escert.upc.edu>
To: jgarzik@pobox.com
Cc: linux-ide@vger.kernel.org
Subject: sata_sx4: it's beta/experimental, but does it work ?
Date: Fri, 30 Jan 2009 10:07:51 +0100 [thread overview]
Message-ID: <4982C367.60000@escert.upc.edu> (raw)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hello Jeff & linux-ide ppl,
I've tried to load this driver after installing openfiler distribution
(kernel 2.6.26.8-1.0.11.smp.gcc3.4.x86.i686), but it complains about
xfermode and does not export any drive to /dev.
I've tried JBOD and RAID5 on promise Ctrl-F boot utility so far. Which
mode should I enable on the controller to make it work even without
hardware acceleration, which I know it's unsupported right now.
Drop me a line if any of you wish to do some testing on it, this machine
is not in production right now.
Thanks !
Roman
PD: Here's the ticket I opened on openfiler, if you want further details:
https://project.openfiler.com/tracker/ticket/880
And here's a relevant dmesg output:
ACPI: PCI interrupt for device 0000:02:0c.0 disabled
libata version 3.00 loaded.
sata_sx4 0000:02:0c.0: version 0.12
ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 20
Local DIMM ECC Enabled
scsi4 : sata_sx4
scsi5 : sata_sx4
scsi6 : sata_sx4
scsi7 : sata_sx4
ata1: SATA max UDMA/133 mmio m1048576@0xfea00000 dimm m32768@0xfe9f8000
port 0xfea00200 irq 20
ata2: SATA max UDMA/133 mmio m1048576@0xfea00000 dimm m32768@0xfe9f8000
port 0xfea00280 irq 20
ata3: SATA max UDMA/133 mmio m1048576@0xfea00000 dimm m32768@0xfe9f8000
port 0xfea00300 irq 20
ata4: SATA max UDMA/133 mmio m1048576@0xfea00000 dimm m32768@0xfe9f8000
port 0xfea00380 irq 20
ata1.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata1.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: qc timeout (cmd 0xef)
ata1.00: failed to set xfermode (err_mask=0x4)
ata1.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata1.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: qc timeout (cmd 0xef)
ata1.00: failed to set xfermode (err_mask=0x4)
ata1.00: limiting speed to UDMA/133:PIO3
ata1.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata1.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: qc timeout (cmd 0xef)
ata1.00: failed to set xfermode (err_mask=0x4)
ata1.00: disabled
ata2.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata2.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata2.00: qc timeout (cmd 0xef)
ata2.00: failed to set xfermode (err_mask=0x4)
ata2.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata2.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata2.00: qc timeout (cmd 0xef)
ata2.00: failed to set xfermode (err_mask=0x4)
ata2.00: limiting speed to UDMA/133:PIO3
ata2.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata2.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata2.00: qc timeout (cmd 0xef)
ata2.00: failed to set xfermode (err_mask=0x4)
ata2.00: disabled
ata3.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata3.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata3.00: qc timeout (cmd 0xef)
ata3.00: failed to set xfermode (err_mask=0x4)
ata3.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata3.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata3.00: qc timeout (cmd 0xef)
ata3.00: failed to set xfermode (err_mask=0x4)
ata3.00: limiting speed to UDMA/133:PIO3
ata3.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata3.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata3.00: qc timeout (cmd 0xef)
ata3.00: failed to set xfermode (err_mask=0x4)
ata3.00: disabled
ata4.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata4.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata4.00: qc timeout (cmd 0xef)
ata4.00: failed to set xfermode (err_mask=0x4)
ata4.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata4.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata4.00: qc timeout (cmd 0xef)
ata4.00: failed to set xfermode (err_mask=0x4)
ata4.00: limiting speed to UDMA/133:PIO3
ata4.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata4.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata4.00: qc timeout (cmd 0xef)
ata4.00: failed to set xfermode (err_mask=0x4)
ata4.00: disabled
ACPI: PCI interrupt for device 0000:02:0c.0 disabled
# lspci
02:0c.0 RAID bus controller: Promise Technology, Inc. PDC20621 [SATA150
SX4] 4 Channel IDE RAID Controller (rev 01)
- --
PGP Key ID: 0x08F80CB5
esCERT-UPC - http://escert.upc.edu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
iEYEARECAAYFAkmCw2YACgkQEqU4jwj4DLWfcgCfTfdHi2eVhi4xTg+QblwXdxuU
mfUAmgONPEyULISu5U3hdISn2BWDhsfN
=anvl
-----END PGP SIGNATURE-----
reply other threads:[~2009-01-30 9:16 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4982C367.60000@escert.upc.edu \
--to=rvalls@escert.upc.edu \
--cc=jgarzik@pobox.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).