Re: [PATCH,v2][1/2] sata-mv: enable HDD led blinking when NCQ is active for GenIIe

[Mark Lord <liml@rtr.ca>]

Mark Lord wrote:
..
> Or rather, exactly *how* did you "disable NCQ" ?
..

And after you answer that, then does this revised patch work?
If not, then perhaps you could try and figure out why,
since I just don't have your hardware available to me here.

Thanks

--- old/drivers/ata/sata_mv.c	2009-03-11 00:50:48.000000000 -0400
+++ new/drivers/ata/sata_mv.c	2009-03-11 10:13:29.000000000 -0400
@@ -251,6 +251,11 @@
 	HC_IRQ_COAL_IO_THRESHOLD_OFS	= 0x000c,
 	HC_IRQ_COAL_TIME_THRESHOLD_OFS	= 0x0010,
 
+	SOC_LED_CTRL_OFS	= 0x2c,
+	SOC_LED_CTRL_BLINK	= (1 << 0),	/* Active LED blink */
+	SOC_LED_CTRL_ACT_PRESENCE = (1 << 2),	/* Multiplex dev presence */
+						/*  with dev activity LED */
+
 	/* Shadow block registers */
 	SHD_BLK_OFS		= 0x100,
 	SHD_CTL_AST_OFS		= 0x20,		/* ofs from SHD_BLK_OFS */
@@ -411,6 +416,7 @@
 	MV_HP_PCIE		= (1 << 9),	/* PCIe bus/regs: 7042 */
 	MV_HP_CUT_THROUGH	= (1 << 10),	/* can use EDMA cut-through */
 	MV_HP_FLAG_SOC		= (1 << 11),	/* SystemOnChip, no PCI */
+	MV_HP_QUIRK_LED_BLINK_EN = (1 << 12),	/* is led blinking enabled? */
 
 	/* Port private flags (pp_flags) */
 	MV_PP_FLAG_EDMA_EN	= (1 << 0),	/* is EDMA engine enabled? */
@@ -1404,6 +1410,62 @@
 	mv_write_cached_reg(mv_ap_base(ap) + EDMA_UNKNOWN_RSVD_OFS, old, new);
 }
 
+/*
+ * SOC chips have an issue whereby the HDD LEDs don't always blink
+ * during I/O when NCQ is enabled. Enabling a special "LED blink" mode
+ * of the SOC takes care of it, generating a steady blink rate when
+ * any drive on the chip is active.
+ *
+ * Unfortunately, the blink mode is a global hardware setting for the SOC,
+ * so we must use it whenever at least one port on the SOC has NCQ enabled.
+ *
+ * We turn "LED blink" off when NCQ is not in use anywhere, because the normal
+ * LED operation works then, and provides better (more accurate) feedback.
+ *
+ * Note that this code assumes that an SOC never has more than one HC onboard.
+ */
+static void mv_soc_led_blink_enable(struct ata_port *ap)
+{
+	struct ata_host *host = ap->host;
+	struct mv_host_priv *hpriv = host->private_data;
+	void __iomem *hc_mmio;
+	u32 led_ctrl;
+
+	if (hpriv->hp_flags & MV_HP_QUIRK_LED_BLINK_EN)
+		return;
+	hpriv->hp_flags |= MV_HP_QUIRK_LED_BLINK_EN;
+	hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no);
+	led_ctrl = readl(hc_mmio + SOC_LED_CTRL_OFS);
+	writel(led_ctrl | SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL_OFS);
+}
+
+static void mv_soc_led_blink_disable(struct ata_port *ap)
+{
+	struct ata_host *host = ap->host;
+	struct mv_host_priv *hpriv = host->private_data;
+	void __iomem *hc_mmio;
+	u32 led_ctrl;
+	unsigned int port;
+
+	if (!(hpriv->hp_flags & MV_HP_QUIRK_LED_BLINK_EN))
+		return;
+
+	/* disable led-blink only if no ports are using NCQ */
+	for (port = 0; port < hpriv->n_ports; port++) {
+		struct ata_port *this_ap = host->ports[port];
+		struct mv_port_priv *pp = this_ap->private_data;
+
+		if (pp->pp_flags & MV_PP_FLAG_EDMA_EN)
+			if (pp->pp_flags & MV_PP_FLAG_NCQ_EN)
+				return;
+	}
+
+	hpriv->hp_flags &= ~MV_HP_QUIRK_LED_BLINK_EN;
+	hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no);
+	led_ctrl = readl(hc_mmio + SOC_LED_CTRL_OFS);
+	writel(led_ctrl & ~SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL_OFS);
+}
+
 static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma)
 {
 	u32 cfg;
@@ -1451,6 +1513,13 @@
 		if (hpriv->hp_flags & MV_HP_CUT_THROUGH)
 			cfg |= (1 << 17); /* enab cut-thru (dis stor&forwrd) */
 		mv_bmdma_enable_iie(ap, !want_edma);
+
+		if (IS_SOC(hpriv)) {
+			if (want_ncq)
+				mv_soc_led_blink_enable(ap);
+			else
+				mv_soc_led_blink_disable(ap);
+		}
 	}
 
 	if (want_ncq) {