* sil3132 eSATA problem
@ 2012-02-15 7:02 Sebastian Muniz
2012-02-16 4:45 ` Robert Hancock
0 siblings, 1 reply; 5+ messages in thread
From: Sebastian Muniz @ 2012-02-15 7:02 UTC (permalink / raw)
To: linux-ide
Hello
Hello!
I am running
Linux ante 2.6.32.55sebita4-reiserfs4 #5 SMP Wed Feb 1 06:24:50 ART 2012
x86_64 GNU/Linux
custom compiled with reiserfs4 patches on an IBM X3200 M3
I have a two port eSATA SIL3132:
10:00.0 RAID bus controller: Silicon Image, Inc. SiI 3132 Serial ATA
Raid II Controller (rev 01)
Subsystem: Silicon Image, Inc. Device 7132
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at 91b04000 (64-bit, non-prefetchable) [size=128]
Memory at 91b00000 (64-bit, non-prefetchable) [size=16K]
I/O ports at 3000 [size=128]
Expansion ROM at 80600000 [disabled] [size=512K]
Capabilities: [54] Power Management version 2
Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Legacy Endpoint, MSI 00
Kernel driver in use: sata_sil24
This gives me this two ports:
[6] sata_sil24
cmd_per_lun=1 host_busy=0 sg_tablesize=253 unchecked_isa_dma=0
dir: /sys/class/scsi_host//host6
device dir: /sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6
[7] sata_sil24
cmd_per_lun=1 host_busy=0 sg_tablesize=253 unchecked_isa_dma=0
dir: /sys/class/scsi_host//host7
device dir: /sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host7
On ata6 I have a Lian Li box with JM393PM with 5 disks:
[6:0:0:0] disk ATA WDC WD20EARS-00S 0957 /dev/sdb
state=running queue_depth=1 scsi_level=6 type=0 device_blocked=0
timeout=30
dir: /sys/bus/scsi/devices/6:0:0:0
[/sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6/target6:0:0/6:0:0:0]
[6:1:0:0] disk ATA WDC WD20EARS-00S 80.0 /dev/sdc
state=running queue_depth=31 scsi_level=6 type=0 device_blocked=0
timeout=30
dir: /sys/bus/scsi/devices/6:1:0:0
[/sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6/target6:1:0/6:1:0:0]
[6:2:0:0] disk ATA WDC WD20EARS-00S 80.0 /dev/sdd
state=running queue_depth=31 scsi_level=6 type=0 device_blocked=0
timeout=30
dir: /sys/bus/scsi/devices/6:2:0:0
[/sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6/target6:2:0/6:2:0:0]
[6:3:0:0] disk ATA WDC WD20EARS-00M 51.0 /dev/sde
state=running queue_depth=31 scsi_level=6 type=0 device_blocked=0
timeout=30
dir: /sys/bus/scsi/devices/6:3:0:0
[/sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6/target6:3:0/6:3:0:0]
[6:4:0:0] disk ATA WDC WD20EARS-00M 51.0 /dev/sdf
state=running queue_depth=31 scsi_level=6 type=0 device_blocked=0
timeout=30
dir: /sys/bus/scsi/devices/6:4:0:0
[/sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6/target6:4:0/6:4:0:0]
And ata7 is _unused_, nothing is connected to it.
However from time to time I see on the logs:
[904916.169177] ata7.00: failed to read SCR 1 (Emask=0x40)
[904916.169210] ata7.01: failed to read SCR 1 (Emask=0x40)
[904916.169239] ata7.02: failed to read SCR 1 (Emask=0x40)
[904916.169268] ata7.03: failed to read SCR 1 (Emask=0x40)
[904916.169293] ata7.04: failed to read SCR 1 (Emask=0x40)
[904916.169322] ata7.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[904916.169367] ata7.01: exception Emask 0x100 SAct 0x1 SErr 0x0 action
0x6 frozen
[904916.169411] ata7.01: failed command: WRITE FPDMA QUEUED
[904916.169440] ata7.01: cmd 61/88:00:b7:e4:2e/03:00:4e:00:00/40 tag 0
ncq 462848 out
[904916.169440] res 90/7c:00:00:00:00/00:00:00:00:90/00 Emask
0x2 (HSM violation)
[904916.169530] ata7.01: status: { Busy }
[904916.169554] ata7.01: error: { UNC IDNF ABRT }
[904916.169579] ata7.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[904916.169623] ata7.03: exception Emask 0x10 SAct 0x4 SErr 0x0 action
0x6 frozen
[904916.169667] ata7.03: irq_stat 0x01060002, failed to transmit command FIS
[904916.169696] ata7.03: failed command: WRITE FPDMA QUEUED
[904916.169724] ata7.03: cmd 61/88:10:b7:e4:2e/03:00:4e:00:00/40 tag 2
ncq 462848 out
[904916.169725] res 90/7c:00:00:00:00/00:00:c0:21:90/00 Emask
0x12 (ATA bus error)
[904916.169811] ata7.03: status: { Busy }
[904916.169834] ata7.03: error: { UNC IDNF ABRT }
[904916.169859] ata7.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action
0x6 frozen
[904916.169904] ata7.15: hard resetting link
[904916.169927] ata7: controller in dubious state, performing PORT_RST
[904918.396264] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[904918.396666] ata7.00: hard resetting link
[904918.731825] ata7.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[904918.731902] ata7.01: hard resetting link
[904919.067090] ata7.01: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[904919.067170] ata7.02: hard resetting link
[904919.402343] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[904919.402420] ata7.03: hard resetting link
[904919.753567] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[904919.753649] ata7.04: hard resetting link
[904920.104789] ata7.04: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[904920.105952] ata7.00: configured for UDMA/100
[904920.118162] ata7.01: configured for UDMA/100
[904920.130177] ata7.02: configured for UDMA/100
[904920.138029] ata7.03: configured for UDMA/100
[904920.145862] ata7.04: configured for UDMA/100
[904920.145997] ata7: EH complete
This is the frequency:
root@ante:~# dmesg|grep "ata7: EH complete"
[409984.923590] ata7: EH complete
[415032.569957] ata7: EH complete
[420312.071009] ata7: EH complete
[421192.345587] ata7: EH complete
[875586.406464] ata7: EH complete
[904920.145997] ata7: EH complete
Questions:
- Is this a problem? Nothing looks wrong at the server, everything works
as expected, but I receive a page from time time because of this error.
- Is there a way to keep the ata7 port down? Kind of disable it.
- Is this the way to deal with this problem?
Thanks a lot in advance,
Sebastian
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: sil3132 eSATA problem
2012-02-15 7:02 sil3132 eSATA problem Sebastian Muniz
@ 2012-02-16 4:45 ` Robert Hancock
[not found] ` <4F3C8C2F.1060300@gmail.com>
0 siblings, 1 reply; 5+ messages in thread
From: Robert Hancock @ 2012-02-16 4:45 UTC (permalink / raw)
To: Sebastian Muniz; +Cc: linux-ide
On 02/15/2012 01:02 AM, Sebastian Muniz wrote:
> Hello
> Hello!
> I am running
> Linux ante 2.6.32.55sebita4-reiserfs4 #5 SMP Wed Feb 1 06:24:50 ART 2012
> x86_64 GNU/Linux
> custom compiled with reiserfs4 patches on an IBM X3200 M3
>
>
> I have a two port eSATA SIL3132:
> 10:00.0 RAID bus controller: Silicon Image, Inc. SiI 3132 Serial ATA
> Raid II Controller (rev 01)
> Subsystem: Silicon Image, Inc. Device 7132
> Flags: bus master, fast devsel, latency 0, IRQ 18
> Memory at 91b04000 (64-bit, non-prefetchable) [size=128]
> Memory at 91b00000 (64-bit, non-prefetchable) [size=16K]
> I/O ports at 3000 [size=128]
> Expansion ROM at 80600000 [disabled] [size=512K]
> Capabilities: [54] Power Management version 2
> Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+
> Capabilities: [70] Express Legacy Endpoint, MSI 00
> Kernel driver in use: sata_sil24
>
> This gives me this two ports:
> [6] sata_sil24
> cmd_per_lun=1 host_busy=0 sg_tablesize=253 unchecked_isa_dma=0
> dir: /sys/class/scsi_host//host6
> device dir: /sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6
> [7] sata_sil24
> cmd_per_lun=1 host_busy=0 sg_tablesize=253 unchecked_isa_dma=0
> dir: /sys/class/scsi_host//host7
> device dir: /sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host7
>
> On ata6 I have a Lian Li box with JM393PM with 5 disks:
> [6:0:0:0] disk ATA WDC WD20EARS-00S 0957 /dev/sdb
> state=running queue_depth=1 scsi_level=6 type=0 device_blocked=0 timeout=30
> dir: /sys/bus/scsi/devices/6:0:0:0
> [/sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6/target6:0:0/6:0:0:0]
>
> [6:1:0:0] disk ATA WDC WD20EARS-00S 80.0 /dev/sdc
> state=running queue_depth=31 scsi_level=6 type=0 device_blocked=0
> timeout=30
> dir: /sys/bus/scsi/devices/6:1:0:0
> [/sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6/target6:1:0/6:1:0:0]
>
> [6:2:0:0] disk ATA WDC WD20EARS-00S 80.0 /dev/sdd
> state=running queue_depth=31 scsi_level=6 type=0 device_blocked=0
> timeout=30
> dir: /sys/bus/scsi/devices/6:2:0:0
> [/sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6/target6:2:0/6:2:0:0]
>
> [6:3:0:0] disk ATA WDC WD20EARS-00M 51.0 /dev/sde
> state=running queue_depth=31 scsi_level=6 type=0 device_blocked=0
> timeout=30
> dir: /sys/bus/scsi/devices/6:3:0:0
> [/sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6/target6:3:0/6:3:0:0]
>
> [6:4:0:0] disk ATA WDC WD20EARS-00M 51.0 /dev/sdf
> state=running queue_depth=31 scsi_level=6 type=0 device_blocked=0
> timeout=30
> dir: /sys/bus/scsi/devices/6:4:0:0
> [/sys/devices/pci0000:00/0000:00:1c.6/0000:10:00.0/host6/target6:4:0/6:4:0:0]
>
>
> And ata7 is _unused_, nothing is connected to it.
>
> However from time to time I see on the logs:
> [904916.169177] ata7.00: failed to read SCR 1 (Emask=0x40)
> [904916.169210] ata7.01: failed to read SCR 1 (Emask=0x40)
> [904916.169239] ata7.02: failed to read SCR 1 (Emask=0x40)
> [904916.169268] ata7.03: failed to read SCR 1 (Emask=0x40)
> [904916.169293] ata7.04: failed to read SCR 1 (Emask=0x40)
> [904916.169322] ata7.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action
> 0x6 frozen
> [904916.169367] ata7.01: exception Emask 0x100 SAct 0x1 SErr 0x0 action
> 0x6 frozen
> [904916.169411] ata7.01: failed command: WRITE FPDMA QUEUED
> [904916.169440] ata7.01: cmd 61/88:00:b7:e4:2e/03:00:4e:00:00/40 tag 0
> ncq 462848 out
> [904916.169440] res 90/7c:00:00:00:00/00:00:00:00:90/00 Emask 0x2 (HSM
> violation)
> [904916.169530] ata7.01: status: { Busy }
> [904916.169554] ata7.01: error: { UNC IDNF ABRT }
> [904916.169579] ata7.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action
> 0x6 frozen
> [904916.169623] ata7.03: exception Emask 0x10 SAct 0x4 SErr 0x0 action
> 0x6 frozen
> [904916.169667] ata7.03: irq_stat 0x01060002, failed to transmit command
> FIS
> [904916.169696] ata7.03: failed command: WRITE FPDMA QUEUED
> [904916.169724] ata7.03: cmd 61/88:10:b7:e4:2e/03:00:4e:00:00/40 tag 2
> ncq 462848 out
> [904916.169725] res 90/7c:00:00:00:00/00:00:c0:21:90/00 Emask 0x12 (ATA
> bus error)
> [904916.169811] ata7.03: status: { Busy }
> [904916.169834] ata7.03: error: { UNC IDNF ABRT }
> [904916.169859] ata7.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action
> 0x6 frozen
> [904916.169904] ata7.15: hard resetting link
> [904916.169927] ata7: controller in dubious state, performing PORT_RST
> [904918.396264] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
> [904918.396666] ata7.00: hard resetting link
> [904918.731825] ata7.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
> [904918.731902] ata7.01: hard resetting link
> [904919.067090] ata7.01: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
> [904919.067170] ata7.02: hard resetting link
> [904919.402343] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
> [904919.402420] ata7.03: hard resetting link
> [904919.753567] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
> [904919.753649] ata7.04: hard resetting link
> [904920.104789] ata7.04: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
> [904920.105952] ata7.00: configured for UDMA/100
> [904920.118162] ata7.01: configured for UDMA/100
> [904920.130177] ata7.02: configured for UDMA/100
> [904920.138029] ata7.03: configured for UDMA/100
> [904920.145862] ata7.04: configured for UDMA/100
> [904920.145997] ata7: EH complete
>
> This is the frequency:
> root@ante:~# dmesg|grep "ata7: EH complete"
> [409984.923590] ata7: EH complete
> [415032.569957] ata7: EH complete
> [420312.071009] ata7: EH complete
> [421192.345587] ata7: EH complete
> [875586.406464] ata7: EH complete
> [904920.145997] ata7: EH complete
>
>
> Questions:
> - Is this a problem? Nothing looks wrong at the server, everything works
> as expected, but I receive a page from time time because of this error.
> - Is there a way to keep the ata7 port down? Kind of disable it.
> - Is this the way to deal with this problem?
Are you sure ata7 is an unused port? I'm pretty sure there must be a
drive on that port and it's throwing errors on writes. Can you post the
full dmesg log?
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2012-02-16 5:03 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-02-15 7:02 sil3132 eSATA problem Sebastian Muniz
2012-02-16 4:45 ` Robert Hancock
[not found] ` <4F3C8C2F.1060300@gmail.com>
2012-02-16 4:57 ` Fwd: " Sebastian Muniz
2012-02-16 4:58 ` Robert Hancock
2012-02-16 5:03 ` Sebastian Muniz
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).