* Re: macbook pro 9.2 stat/ata bus error [not found] <CAAW1UO_X9eaBoiHMdj-ntCjGgBKpA6A_EDA2zifDf7f7dbs4Xw@mail.gmail.com> @ 2012-11-07 3:41 ` Azat Khuzhin 2012-11-07 7:21 ` Azat Khuzhin 2012-11-09 3:48 ` Robert Hancock 0 siblings, 2 replies; 5+ messages in thread From: Azat Khuzhin @ 2012-11-07 3:41 UTC (permalink / raw) To: Linux Kernel Mailing List, linux-ide Anybody? On Mon, Nov 5, 2012 at 7:28 PM, Azat Khuzhin <dohardgopro@gmail.com> wrote: > After installing linux on macbook 9.2 (mid 2012), I have next errors > in dmesg log: > > [ 389.623828] EXT4-fs (sda4): re-mounted. Opts: > errors=remount-ro,data=ordered,commit=600 > [ 410.038465] NMI watchdog: enabled on all CPUs, permanently consumes > one hw-PMU counter. > [ 410.075042] ehci_hcd 0000:00:1a.0: setting latency timer to 64 > [ 410.483526] EXT4-fs (sda4): re-mounted. Opts: > errors=remount-ro,data=ordered,commit=0 > [ 1401.834509] EXT4-fs (sda4): re-mounted. Opts: > errors=remount-ro,data=ordered,commit=1800 > [ 1406.467268] NMI watchdog: enabled on all CPUs, permanently consumes > one hw-PMU counter. > [ 1406.506769] ehci_hcd 0000:00:1a.0: setting latency timer to 64 > [ 1406.590122] EXT4-fs (sda4): re-mounted. Opts: > errors=remount-ro,data=ordered,commit=0 > [ 1407.492260] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 > action 0xe frozen > [ 1407.494441] ata2.00: irq_stat 0x00400000, PHY RDY changed > [ 1407.495238] ata2: SError: { PHYRdyChg CommWake } > [ 1407.496035] sr 1:0:0:0: CDB: > [ 1407.497333] Get event status notification: 4a 01 00 00 10 00 00 00 08 00 > [ 1407.498285] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 > pio 16392 in > [ 1407.498285] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask > 0x10 (ATA bus error) > [ 1407.501987] ata2.00: status: { DRDY } > [ 1407.502882] ata2: hard resetting link > [ 1408.230302] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > [ 1408.233279] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) > filtered out > [ 1408.237467] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) > filtered out > [ 1408.239084] ata2.00: configured for UDMA/100 > [ 1408.262238] ata2: EH complete > [ 3565.785609] EXT4-fs (sda4): re-mounted. Opts: > errors=remount-ro,data=ordered,commit=1800 > [ 3576.921499] NMI watchdog: enabled on all CPUs, permanently consumes > one hw-PMU counter. > [ 3576.958624] ehci_hcd 0000:00:1a.0: setting latency timer to 64 > [ 3577.114612] EXT4-fs (sda4): re-mounted. Opts: > errors=remount-ro,data=ordered,commit=0 > [ 3577.923688] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 > action 0xe frozen > [ 3577.925852] ata2.00: irq_stat 0x00400000, PHY RDY changed > [ 3577.926746] ata2: SError: { PHYRdyChg CommWake } > [ 3577.927544] sr 1:0:0:0: CDB: > [ 3577.928345] Get event status notification: 4a 01 00 00 10 00 00 00 08 00 > [ 3577.929642] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 > pio 16392 in > [ 3577.929642] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask > 0x10 (ATA bus error) > [ 3577.932954] ata2.00: status: { DRDY } > [ 3577.934264] ata2: hard resetting link > [ 3578.662228] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > [ 3578.665211] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) > filtered out > [ 3578.669355] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) > filtered out > [ 3578.670969] ata2.00: configured for UDMA/100 > [ 3578.694145] ata2: EH complete > > Is it linux driver, or maybe > > $ lspci # sata information only > 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family > 6-port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) > Subsystem: Intel Corporation Device 7270 > Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 20 > I/O ports at 2098 [size=8] > I/O ports at 20bc [size=4] > I/O ports at 2090 [size=8] > I/O ports at 20b8 [size=4] > I/O ports at 2060 [size=32] > Memory at a0816000 (32-bit, non-prefetchable) [size=2K] > Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- > Capabilities: [70] Power Management version 3 > Capabilities: [a8] SATA HBA v1.0 > Capabilities: [b0] PCI Advanced Features > Kernel driver in use: ahci > > $ uname -a > Linux macbook-pro 3.6.5macbook-pro-custom-v0.1 #4 SMP Sun Nov 4 > 12:39:03 UTC 2012 x86_64 GNU/Linux > $ cat /etc/debian_version > wheezy/sid > > In OSX there is no errors with hard drive. > > What else can I do investigate this situation next? > > -- > Azat Khuzhin -- Azat Khuzhin ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: macbook pro 9.2 stat/ata bus error 2012-11-07 3:41 ` macbook pro 9.2 stat/ata bus error Azat Khuzhin @ 2012-11-07 7:21 ` Azat Khuzhin 2012-11-09 3:48 ` Robert Hancock 1 sibling, 0 replies; 5+ messages in thread From: Azat Khuzhin @ 2012-11-07 7:21 UTC (permalink / raw) To: Linux Kernel Mailing List, linux-ide Also I want to note that some times notebook was suspended. But this errors don't appears every time before suspend or just after resume. On Wed, Nov 7, 2012 at 7:41 AM, Azat Khuzhin <dohardgopro@gmail.com> wrote: > Anybody? > > On Mon, Nov 5, 2012 at 7:28 PM, Azat Khuzhin <dohardgopro@gmail.com> wrote: >> After installing linux on macbook 9.2 (mid 2012), I have next errors >> in dmesg log: >> >> [ 389.623828] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=600 >> [ 410.038465] NMI watchdog: enabled on all CPUs, permanently consumes >> one hw-PMU counter. >> [ 410.075042] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >> [ 410.483526] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=0 >> [ 1401.834509] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=1800 >> [ 1406.467268] NMI watchdog: enabled on all CPUs, permanently consumes >> one hw-PMU counter. >> [ 1406.506769] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >> [ 1406.590122] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=0 >> [ 1407.492260] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 >> action 0xe frozen >> [ 1407.494441] ata2.00: irq_stat 0x00400000, PHY RDY changed >> [ 1407.495238] ata2: SError: { PHYRdyChg CommWake } >> [ 1407.496035] sr 1:0:0:0: CDB: >> [ 1407.497333] Get event status notification: 4a 01 00 00 10 00 00 00 08 00 >> [ 1407.498285] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 >> pio 16392 in >> [ 1407.498285] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask >> 0x10 (ATA bus error) >> [ 1407.501987] ata2.00: status: { DRDY } >> [ 1407.502882] ata2: hard resetting link >> [ 1408.230302] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >> [ 1408.233279] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >> filtered out >> [ 1408.237467] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >> filtered out >> [ 1408.239084] ata2.00: configured for UDMA/100 >> [ 1408.262238] ata2: EH complete >> [ 3565.785609] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=1800 >> [ 3576.921499] NMI watchdog: enabled on all CPUs, permanently consumes >> one hw-PMU counter. >> [ 3576.958624] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >> [ 3577.114612] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=0 >> [ 3577.923688] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 >> action 0xe frozen >> [ 3577.925852] ata2.00: irq_stat 0x00400000, PHY RDY changed >> [ 3577.926746] ata2: SError: { PHYRdyChg CommWake } >> [ 3577.927544] sr 1:0:0:0: CDB: >> [ 3577.928345] Get event status notification: 4a 01 00 00 10 00 00 00 08 00 >> [ 3577.929642] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 >> pio 16392 in >> [ 3577.929642] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask >> 0x10 (ATA bus error) >> [ 3577.932954] ata2.00: status: { DRDY } >> [ 3577.934264] ata2: hard resetting link >> [ 3578.662228] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >> [ 3578.665211] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >> filtered out >> [ 3578.669355] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >> filtered out >> [ 3578.670969] ata2.00: configured for UDMA/100 >> [ 3578.694145] ata2: EH complete >> >> Is it linux driver, or maybe >> >> $ lspci # sata information only >> 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family >> 6-port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) >> Subsystem: Intel Corporation Device 7270 >> Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 20 >> I/O ports at 2098 [size=8] >> I/O ports at 20bc [size=4] >> I/O ports at 2090 [size=8] >> I/O ports at 20b8 [size=4] >> I/O ports at 2060 [size=32] >> Memory at a0816000 (32-bit, non-prefetchable) [size=2K] >> Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- >> Capabilities: [70] Power Management version 3 >> Capabilities: [a8] SATA HBA v1.0 >> Capabilities: [b0] PCI Advanced Features >> Kernel driver in use: ahci >> >> $ uname -a >> Linux macbook-pro 3.6.5macbook-pro-custom-v0.1 #4 SMP Sun Nov 4 >> 12:39:03 UTC 2012 x86_64 GNU/Linux >> $ cat /etc/debian_version >> wheezy/sid >> >> In OSX there is no errors with hard drive. >> >> What else can I do investigate this situation next? >> >> -- >> Azat Khuzhin > > > > -- > Azat Khuzhin -- Azat Khuzhin ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: macbook pro 9.2 stat/ata bus error 2012-11-07 3:41 ` macbook pro 9.2 stat/ata bus error Azat Khuzhin 2012-11-07 7:21 ` Azat Khuzhin @ 2012-11-09 3:48 ` Robert Hancock 2012-11-10 13:22 ` Azat Khuzhin 1 sibling, 1 reply; 5+ messages in thread From: Robert Hancock @ 2012-11-09 3:48 UTC (permalink / raw) To: Azat Khuzhin; +Cc: Linux Kernel Mailing List, linux-ide On 11/06/2012 09:41 PM, Azat Khuzhin wrote: > Anybody? > > On Mon, Nov 5, 2012 at 7:28 PM, Azat Khuzhin <dohardgopro@gmail.com> wrote: >> After installing linux on macbook 9.2 (mid 2012), I have next errors >> in dmesg log: >> >> [ 389.623828] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=600 >> [ 410.038465] NMI watchdog: enabled on all CPUs, permanently consumes >> one hw-PMU counter. >> [ 410.075042] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >> [ 410.483526] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=0 >> [ 1401.834509] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=1800 >> [ 1406.467268] NMI watchdog: enabled on all CPUs, permanently consumes >> one hw-PMU counter. >> [ 1406.506769] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >> [ 1406.590122] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=0 >> [ 1407.492260] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 >> action 0xe frozen >> [ 1407.494441] ata2.00: irq_stat 0x00400000, PHY RDY changed >> [ 1407.495238] ata2: SError: { PHYRdyChg CommWake } >> [ 1407.496035] sr 1:0:0:0: CDB: >> [ 1407.497333] Get event status notification: 4a 01 00 00 10 00 00 00 08 00 >> [ 1407.498285] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 >> pio 16392 in >> [ 1407.498285] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask >> 0x10 (ATA bus error) >> [ 1407.501987] ata2.00: status: { DRDY } >> [ 1407.502882] ata2: hard resetting link >> [ 1408.230302] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >> [ 1408.233279] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >> filtered out >> [ 1408.237467] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >> filtered out >> [ 1408.239084] ata2.00: configured for UDMA/100 >> [ 1408.262238] ata2: EH complete Is this after a resume? It could be that for some reason the SATA link is a little bit unstable right after the machine powers up again. There may not be much the kernel can do about this.. >> [ 3565.785609] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=1800 >> [ 3576.921499] NMI watchdog: enabled on all CPUs, permanently consumes >> one hw-PMU counter. >> [ 3576.958624] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >> [ 3577.114612] EXT4-fs (sda4): re-mounted. Opts: >> errors=remount-ro,data=ordered,commit=0 >> [ 3577.923688] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 >> action 0xe frozen >> [ 3577.925852] ata2.00: irq_stat 0x00400000, PHY RDY changed >> [ 3577.926746] ata2: SError: { PHYRdyChg CommWake } >> [ 3577.927544] sr 1:0:0:0: CDB: >> [ 3577.928345] Get event status notification: 4a 01 00 00 10 00 00 00 08 00 >> [ 3577.929642] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 >> pio 16392 in >> [ 3577.929642] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask >> 0x10 (ATA bus error) >> [ 3577.932954] ata2.00: status: { DRDY } >> [ 3577.934264] ata2: hard resetting link >> [ 3578.662228] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >> [ 3578.665211] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >> filtered out >> [ 3578.669355] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >> filtered out >> [ 3578.670969] ata2.00: configured for UDMA/100 >> [ 3578.694145] ata2: EH complete >> >> Is it linux driver, or maybe >> >> $ lspci # sata information only >> 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family >> 6-port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) >> Subsystem: Intel Corporation Device 7270 >> Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 20 >> I/O ports at 2098 [size=8] >> I/O ports at 20bc [size=4] >> I/O ports at 2090 [size=8] >> I/O ports at 20b8 [size=4] >> I/O ports at 2060 [size=32] >> Memory at a0816000 (32-bit, non-prefetchable) [size=2K] >> Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- >> Capabilities: [70] Power Management version 3 >> Capabilities: [a8] SATA HBA v1.0 >> Capabilities: [b0] PCI Advanced Features >> Kernel driver in use: ahci >> >> $ uname -a >> Linux macbook-pro 3.6.5macbook-pro-custom-v0.1 #4 SMP Sun Nov 4 >> 12:39:03 UTC 2012 x86_64 GNU/Linux >> $ cat /etc/debian_version >> wheezy/sid >> >> In OSX there is no errors with hard drive. >> >> What else can I do investigate this situation next? >> >> -- >> Azat Khuzhin > > > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: macbook pro 9.2 stat/ata bus error 2012-11-09 3:48 ` Robert Hancock @ 2012-11-10 13:22 ` Azat Khuzhin 2012-11-11 10:54 ` Azat Khuzhin 0 siblings, 1 reply; 5+ messages in thread From: Azat Khuzhin @ 2012-11-10 13:22 UTC (permalink / raw) To: Robert Hancock; +Cc: Linux Kernel Mailing List, linux-ide Yeah, I'm guessed about this. Thanks for reply. On Fri, Nov 9, 2012 at 7:48 AM, Robert Hancock <hancockrwd@gmail.com> wrote: > On 11/06/2012 09:41 PM, Azat Khuzhin wrote: >> >> Anybody? >> >> On Mon, Nov 5, 2012 at 7:28 PM, Azat Khuzhin <dohardgopro@gmail.com> >> wrote: >>> >>> After installing linux on macbook 9.2 (mid 2012), I have next errors >>> in dmesg log: >>> >>> [ 389.623828] EXT4-fs (sda4): re-mounted. Opts: >>> errors=remount-ro,data=ordered,commit=600 >>> [ 410.038465] NMI watchdog: enabled on all CPUs, permanently consumes >>> one hw-PMU counter. >>> [ 410.075042] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >>> [ 410.483526] EXT4-fs (sda4): re-mounted. Opts: >>> errors=remount-ro,data=ordered,commit=0 >>> [ 1401.834509] EXT4-fs (sda4): re-mounted. Opts: >>> errors=remount-ro,data=ordered,commit=1800 >>> [ 1406.467268] NMI watchdog: enabled on all CPUs, permanently consumes >>> one hw-PMU counter. >>> [ 1406.506769] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >>> [ 1406.590122] EXT4-fs (sda4): re-mounted. Opts: >>> errors=remount-ro,data=ordered,commit=0 >>> [ 1407.492260] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 >>> action 0xe frozen >>> [ 1407.494441] ata2.00: irq_stat 0x00400000, PHY RDY changed >>> [ 1407.495238] ata2: SError: { PHYRdyChg CommWake } >>> [ 1407.496035] sr 1:0:0:0: CDB: >>> [ 1407.497333] Get event status notification: 4a 01 00 00 10 00 00 00 08 >>> 00 >>> [ 1407.498285] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 >>> pio 16392 in >>> [ 1407.498285] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask >>> 0x10 (ATA bus error) >>> [ 1407.501987] ata2.00: status: { DRDY } >>> [ 1407.502882] ata2: hard resetting link >>> [ 1408.230302] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >>> [ 1408.233279] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >>> filtered out >>> [ 1408.237467] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >>> filtered out >>> [ 1408.239084] ata2.00: configured for UDMA/100 >>> [ 1408.262238] ata2: EH complete > > > Is this after a resume? It could be that for some reason the SATA link is a > little bit unstable right after the machine powers up again. There may not > be much the kernel can do about this.. > > >>> [ 3565.785609] EXT4-fs (sda4): re-mounted. Opts: >>> errors=remount-ro,data=ordered,commit=1800 >>> [ 3576.921499] NMI watchdog: enabled on all CPUs, permanently consumes >>> one hw-PMU counter. >>> [ 3576.958624] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >>> [ 3577.114612] EXT4-fs (sda4): re-mounted. Opts: >>> errors=remount-ro,data=ordered,commit=0 >>> [ 3577.923688] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 >>> action 0xe frozen >>> [ 3577.925852] ata2.00: irq_stat 0x00400000, PHY RDY changed >>> [ 3577.926746] ata2: SError: { PHYRdyChg CommWake } >>> [ 3577.927544] sr 1:0:0:0: CDB: >>> [ 3577.928345] Get event status notification: 4a 01 00 00 10 00 00 00 08 >>> 00 >>> [ 3577.929642] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 >>> pio 16392 in >>> [ 3577.929642] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask >>> 0x10 (ATA bus error) >>> [ 3577.932954] ata2.00: status: { DRDY } >>> [ 3577.934264] ata2: hard resetting link >>> [ 3578.662228] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >>> [ 3578.665211] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >>> filtered out >>> [ 3578.669355] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >>> filtered out >>> [ 3578.670969] ata2.00: configured for UDMA/100 >>> [ 3578.694145] ata2: EH complete >>> >>> Is it linux driver, or maybe >>> >>> $ lspci # sata information only >>> 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family >>> 6-port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) >>> Subsystem: Intel Corporation Device 7270 >>> Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 20 >>> I/O ports at 2098 [size=8] >>> I/O ports at 20bc [size=4] >>> I/O ports at 2090 [size=8] >>> I/O ports at 20b8 [size=4] >>> I/O ports at 2060 [size=32] >>> Memory at a0816000 (32-bit, non-prefetchable) [size=2K] >>> Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- >>> Capabilities: [70] Power Management version 3 >>> Capabilities: [a8] SATA HBA v1.0 >>> Capabilities: [b0] PCI Advanced Features >>> Kernel driver in use: ahci >>> >>> $ uname -a >>> Linux macbook-pro 3.6.5macbook-pro-custom-v0.1 #4 SMP Sun Nov 4 >>> 12:39:03 UTC 2012 x86_64 GNU/Linux >>> $ cat /etc/debian_version >>> wheezy/sid >>> >>> In OSX there is no errors with hard drive. >>> >>> What else can I do investigate this situation next? >>> >>> -- >>> Azat Khuzhin >> >> >> >> > -- Azat Khuzhin ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: macbook pro 9.2 stat/ata bus error 2012-11-10 13:22 ` Azat Khuzhin @ 2012-11-11 10:54 ` Azat Khuzhin 0 siblings, 0 replies; 5+ messages in thread From: Azat Khuzhin @ 2012-11-11 10:54 UTC (permalink / raw) To: Robert Hancock; +Cc: Linux Kernel Mailing List, linux-ide Also I have notice next thing: At 04:21 I close lid, and laptop automatically suspend, with the following messages in the log: Nov 11 04:21:49 macbook-pro-sq kernel: [19489.114021] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen Nov 11 04:21:49 macbook-pro-sq kernel: [19489.116459] ata2.00: irq_stat 0x00400000, PHY RDY changed Nov 11 04:21:49 macbook-pro-sq kernel: [19489.117665] ata2: SError: { PHYRdyChg CommWake } Nov 11 04:21:49 macbook-pro-sq kernel: [19489.118854] sr 1:0:0:0: CDB: Nov 11 04:21:49 macbook-pro-sq kernel: [19489.120061] Get event status notification: 4a 01 00 00 10 00 00 00 08 00 Nov 11 04:21:49 macbook-pro-sq kernel: [19489.121275] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 pio 16392 in Nov 11 04:21:49 macbook-pro-sq kernel: [19489.121275] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error) Nov 11 04:21:49 macbook-pro-sq kernel: [19489.126075] ata2.00: status: { DRDY } Nov 11 04:21:49 macbook-pro-sq kernel: [19489.127304] ata2: hard resetting link But when I try to resume, it not turn on normally, the monitor don't bright. Laptop came out of suspend, I detected this by indicator at the front. I think that because of it can't read from HDD. Am I right? What can I do next to investigate further? On Sat, Nov 10, 2012 at 5:22 PM, Azat Khuzhin <dohardgopro@gmail.com> wrote: > Yeah, I'm guessed about this. > Thanks for reply. > > On Fri, Nov 9, 2012 at 7:48 AM, Robert Hancock <hancockrwd@gmail.com> wrote: >> On 11/06/2012 09:41 PM, Azat Khuzhin wrote: >>> >>> Anybody? >>> >>> On Mon, Nov 5, 2012 at 7:28 PM, Azat Khuzhin <dohardgopro@gmail.com> >>> wrote: >>>> >>>> After installing linux on macbook 9.2 (mid 2012), I have next errors >>>> in dmesg log: >>>> >>>> [ 389.623828] EXT4-fs (sda4): re-mounted. Opts: >>>> errors=remount-ro,data=ordered,commit=600 >>>> [ 410.038465] NMI watchdog: enabled on all CPUs, permanently consumes >>>> one hw-PMU counter. >>>> [ 410.075042] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >>>> [ 410.483526] EXT4-fs (sda4): re-mounted. Opts: >>>> errors=remount-ro,data=ordered,commit=0 >>>> [ 1401.834509] EXT4-fs (sda4): re-mounted. Opts: >>>> errors=remount-ro,data=ordered,commit=1800 >>>> [ 1406.467268] NMI watchdog: enabled on all CPUs, permanently consumes >>>> one hw-PMU counter. >>>> [ 1406.506769] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >>>> [ 1406.590122] EXT4-fs (sda4): re-mounted. Opts: >>>> errors=remount-ro,data=ordered,commit=0 >>>> [ 1407.492260] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 >>>> action 0xe frozen >>>> [ 1407.494441] ata2.00: irq_stat 0x00400000, PHY RDY changed >>>> [ 1407.495238] ata2: SError: { PHYRdyChg CommWake } >>>> [ 1407.496035] sr 1:0:0:0: CDB: >>>> [ 1407.497333] Get event status notification: 4a 01 00 00 10 00 00 00 08 >>>> 00 >>>> [ 1407.498285] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 >>>> pio 16392 in >>>> [ 1407.498285] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask >>>> 0x10 (ATA bus error) >>>> [ 1407.501987] ata2.00: status: { DRDY } >>>> [ 1407.502882] ata2: hard resetting link >>>> [ 1408.230302] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >>>> [ 1408.233279] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >>>> filtered out >>>> [ 1408.237467] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >>>> filtered out >>>> [ 1408.239084] ata2.00: configured for UDMA/100 >>>> [ 1408.262238] ata2: EH complete >> >> >> Is this after a resume? It could be that for some reason the SATA link is a >> little bit unstable right after the machine powers up again. There may not >> be much the kernel can do about this.. >> >> >>>> [ 3565.785609] EXT4-fs (sda4): re-mounted. Opts: >>>> errors=remount-ro,data=ordered,commit=1800 >>>> [ 3576.921499] NMI watchdog: enabled on all CPUs, permanently consumes >>>> one hw-PMU counter. >>>> [ 3576.958624] ehci_hcd 0000:00:1a.0: setting latency timer to 64 >>>> [ 3577.114612] EXT4-fs (sda4): re-mounted. Opts: >>>> errors=remount-ro,data=ordered,commit=0 >>>> [ 3577.923688] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x50000 >>>> action 0xe frozen >>>> [ 3577.925852] ata2.00: irq_stat 0x00400000, PHY RDY changed >>>> [ 3577.926746] ata2: SError: { PHYRdyChg CommWake } >>>> [ 3577.927544] sr 1:0:0:0: CDB: >>>> [ 3577.928345] Get event status notification: 4a 01 00 00 10 00 00 00 08 >>>> 00 >>>> [ 3577.929642] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 >>>> pio 16392 in >>>> [ 3577.929642] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask >>>> 0x10 (ATA bus error) >>>> [ 3577.932954] ata2.00: status: { DRDY } >>>> [ 3577.934264] ata2: hard resetting link >>>> [ 3578.662228] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >>>> [ 3578.665211] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >>>> filtered out >>>> [ 3578.669355] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) >>>> filtered out >>>> [ 3578.670969] ata2.00: configured for UDMA/100 >>>> [ 3578.694145] ata2: EH complete >>>> >>>> Is it linux driver, or maybe >>>> >>>> $ lspci # sata information only >>>> 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family >>>> 6-port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) >>>> Subsystem: Intel Corporation Device 7270 >>>> Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 20 >>>> I/O ports at 2098 [size=8] >>>> I/O ports at 20bc [size=4] >>>> I/O ports at 2090 [size=8] >>>> I/O ports at 20b8 [size=4] >>>> I/O ports at 2060 [size=32] >>>> Memory at a0816000 (32-bit, non-prefetchable) [size=2K] >>>> Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- >>>> Capabilities: [70] Power Management version 3 >>>> Capabilities: [a8] SATA HBA v1.0 >>>> Capabilities: [b0] PCI Advanced Features >>>> Kernel driver in use: ahci >>>> >>>> $ uname -a >>>> Linux macbook-pro 3.6.5macbook-pro-custom-v0.1 #4 SMP Sun Nov 4 >>>> 12:39:03 UTC 2012 x86_64 GNU/Linux >>>> $ cat /etc/debian_version >>>> wheezy/sid >>>> >>>> In OSX there is no errors with hard drive. >>>> >>>> What else can I do investigate this situation next? >>>> >>>> -- >>>> Azat Khuzhin >>> >>> >>> >>> >> > > > > -- > Azat Khuzhin -- Azat Khuzhin ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2012-11-11 10:54 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <CAAW1UO_X9eaBoiHMdj-ntCjGgBKpA6A_EDA2zifDf7f7dbs4Xw@mail.gmail.com>
2012-11-07 3:41 ` macbook pro 9.2 stat/ata bus error Azat Khuzhin
2012-11-07 7:21 ` Azat Khuzhin
2012-11-09 3:48 ` Robert Hancock
2012-11-10 13:22 ` Azat Khuzhin
2012-11-11 10:54 ` Azat Khuzhin
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).