* Re: AHCI backplane errors in 2.6.27
2008-11-19 19:17 ` David Milburn
@ 2008-11-19 20:21 ` Frank D. Cringle
0 siblings, 0 replies; 4+ messages in thread
From: Frank D. Cringle @ 2008-11-19 20:21 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1: Type: text/plain, Size: 1254 bytes --]
David Milburn writes:
> Frank D. Cringle wrote:
>> Lazy <lazy404@gmail.com> writes:
>>> When booting 2.6.27-rc1 kernel on out intel SR1530HSH ( Quad core Xeon X3320)
>>> Sata controller is ICH9r running in AHCI mode with newest bios.
>>>
>>> After loading ahci driver backplane leds go amber which indicates a
>>> non fatal error according to my intel resseller.
>> I see the same effect on a "FUJITSU SIEMENS PRIMERGY TX150 S6" which
>> also has a ICH9r, running with the fake megaraid disabled in the bios.
>> This has 4 hotswap drive bays. When I boot from drive 0, the remaining
>> drives all blink their orange fault led.
>
> ahci_sw_activity_blink should only be changing the state of
> the activity led only when emp->activity has changed.
>
> From the sata ahci spec for Byte 2-3 of the led message
>
> The LED bit locations are:
> Bits 2:0 - Activity LED (may be driven by hardware)
> Bits 5:3 - Vendor Specific LED (e.g. locate)
> Bits 8:6 - Vendor Specific LED (e.g. fault)
> Bits 15:9 - Reserved
>
> Does this patch (against 2.6.27) make a difference?
Afraid not. When I boot without ahci.ahci_em_messages=0, the LEDs on
drives 1,2,3 all blink continuously. Other than that, there does not
seem to be a problem.
[-- Attachment #2: boot log --]
[-- Type: text/plain, Size: 76577 bytes --]
[ 0.000000] Linux version 2.6.27-gentoo-r3 (root@bowie) (gcc version 4.3.2 (Gentoo 4.3.2 p1.0) ) #3 SMP Wed Nov 19 21:03:46 CET 2008
[ 0.000000] Command line: root=/dev/md3 vga=0x31a video=vesafb:ypan
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009cc00 (usable)
[ 0.000000] BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007feb0000 (usable)
[ 0.000000] BIOS-e820: 000000007feb0000 - 000000007feb7000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007feb7000 - 000000007feba000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007feba000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000e4000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000200000000 (usable)
[ 0.000000] DMI present.
[ 0.000000] last_pfn = 0x200000 max_arch_pfn = 0x3ffffffff
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] last_pfn = 0x7feb0 max_arch_pfn = 0x3ffffffff
[ 0.000000] init_memory_mapping
[ 0.000000] 0000000000 - 007fe00000 page 2M
[ 0.000000] 007fe00000 - 007feb0000 page 4k
[ 0.000000] kernel direct mapping tables up to 7feb0000 @ 8000-c000
[ 0.000000] last_map_addr: 7feb0000 end: 7feb0000
[ 0.000000] init_memory_mapping
[ 0.000000] 0100000000 - 0200000000 page 2M
[ 0.000000] kernel direct mapping tables up to 200000000 @ a000-13000
[ 0.000000] last_map_addr: 200000000 end: 200000000
[ 0.000000] ACPI: RSDP 000F79D0, 0014 (r0 PTLTD )
[ 0.000000] ACPI: RSDT 7FEB19D2, 005C (r1 PTLTD RSDT 60000 LTP 0)
[ 0.000000] ACPI: FACP 7FEB6579, 0074 (r1 FSC 60000 F4240)
[ 0.000000] ACPI: DSDT 7FEB1A2E, 4B4B (r1 FSC D2559 60000 MSFT 3000001)
[ 0.000000] ACPI: FACS 7FEB9FC0, 0040
[ 0.000000] ACPI: TCPA 7FEB65ED, 0032 (r1 Phoeni x 60000 TL 0)
[ 0.000000] ACPI: EINJ 7FEB661F, 01B0 (r1 PTL WHEAPTL 60000 PTL 1)
[ 0.000000] ACPI: HEST 7FEB67CF, 0268 (r1 PTL WHEAPTL 60000 PTL 1)
[ 0.000000] ACPI: BERT 7FEB6A37, 0030 (r1 PTL WHEAPTL 60000 PTL 1)
[ 0.000000] ACPI: SSDT 7FEB6A67, 00E1 (r1 wheaos wheaosc 60000 INTL 20050624)
[ 0.000000] ACPI: ERST 7FEB6B48, 0270 (r1 PTL WHEAPTL 60000 PTL 1)
[ 0.000000] ACPI: SSDT 7FEB6DB8, 007A (r1 FSC CST_CPU0 60000 CSF 1)
[ 0.000000] ACPI: SSDT 7FEB6E32, 007A (r1 FSC CST_CPU1 60000 CSF 1)
[ 0.000000] ACPI: SPCR 7FEB6EAC, 0050 (r1 PTLTD $UCRTBL$ 60000 PTL 1)
[ 0.000000] ACPI: MCFG 7FEB6EFC, 003C (r1 PTLTD MCFG 60000 LTP 0)
[ 0.000000] ACPI: HPET 7FEB6F38, 0038 (r1 PTLTD HPETTBL 60000 LTP 1)
[ 0.000000] ACPI: APIC 7FEB6F70, 0068 (r1 PTLTD APIC 60000 LTP 0)
[ 0.000000] ACPI: BOOT 7FEB6FD8, 0028 (r1 PTLTD $SBFTBL$ 60000 LTP 1)
[ 0.000000] ACPI: DMI detected: Fujitsu Siemens
[ 0.000000] (6 early reservations) ==> bootmem [0000000000 - 0200000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0000200000 - 00009c3898] TEXT DATA BSS ==> [0000200000 - 00009c3898]
[ 0.000000] #3 [000009cc00 - 0000100000] BIOS reserved ==> [000009cc00 - 0000100000]
[ 0.000000] #4 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
[ 0.000000] #5 [000000a000 - 000000e000] PGTABLE ==> [000000a000 - 000000e000]
[ 0.000000] [ffffe20000000000-ffffe20006ffffff] PMD -> [ffff880028200000-ffff88002f1fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00200000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009c
[ 0.000000] 0: 0x00000100 -> 0x0007feb0
[ 0.000000] 0: 0x00100000 -> 0x00200000
[ 0.000000] On node 0 totalpages: 1572428
[ 0.000000] DMA zone: 1845 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 505576 pages, LIFO batch:31
[ 0.000000] Normal zone: 1034240 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0xffffffff base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007feb0000 - 000000007feb7000
[ 0.000000] PM: Registered nosave memory: 000000007feb7000 - 000000007feba000
[ 0.000000] PM: Registered nosave memory: 000000007feba000 - 0000000080000000
[ 0.000000] PM: Registered nosave memory: 0000000080000000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000e4000000
[ 0.000000] PM: Registered nosave memory: 00000000e4000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
[ 0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffb00000
[ 0.000000] PM: Registered nosave memory: 00000000ffb00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] PERCPU: Allocating 56096 bytes of per cpu data
[ 0.000000] NR_CPUS: 4, nr_cpu_ids: 2, nr_node_ids 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1541661
[ 0.000000] Kernel command line: root=/dev/md3 vga=0x31a video=vesafb:ypan
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] TSC: PIT calibration confirmed by PMTIMER.
[ 0.000000] TSC: using PIT calibration value
[ 0.000000] Detected 2992.472 MHz processor.
[ 0.000999] Console: colour dummy device 80x25
[ 0.000999] console [tty0] enabled
[ 0.000999] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.000999] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000999] Checking aperture...
[ 0.000999] No AGP bridge found
[ 0.000999] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.000999] Placing software IO TLB between 0x20000000 - 0x24000000
[ 0.000999] Memory: 6087468k/8388608k available (4615k kernel code, 201300k reserved, 1926k data, 452k init)
[ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.000999] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000999] hpet clockevent registered
[ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 5984.94 BogoMIPS (lpj=2992472)
[ 0.000999] Mount-cache hash table entries: 256
[ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000999] CPU: L2 cache: 6144K
[ 0.000999] CPU: Physical Processor ID: 0
[ 0.000999] CPU: Processor Core ID: 0
[ 0.000999] CPU0: Thermal monitoring enabled (TM2)
[ 0.000999] using mwait in idle threads.
[ 0.002115] ACPI: Core revision 20080609
[ 0.009150] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.019158] CPU0: Intel(R) Xeon(R) CPU E3110 @ 3.00GHz stepping 06
[ 0.019163] Using local APIC timer interrupts.
[ 0.020002] APIC timer calibration result 20781094
[ 0.020004] Detected 20.781 MHz APIC timer.
[ 0.020084] Booting processor 1/1 ip 6000
[ 0.000999] Initializing CPU#1
[ 0.000999] Calibrating delay using timer specific routine.. 5984.96 BogoMIPS (lpj=2992482)
[ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000999] CPU: L2 cache: 6144K
[ 0.000999] CPU: Physical Processor ID: 0
[ 0.000999] CPU: Processor Core ID: 1
[ 0.000999] CPU1: Thermal monitoring enabled (TM2)
[ 0.000999] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.092394] CPU1: Intel(R) Xeon(R) CPU E3110 @ 3.00GHz stepping 06
[ 0.092419] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.093000] Brought up 2 CPUs
[ 0.093003] Total of 2 processors activated (11969.90 BogoMIPS).
[ 0.093063] net_namespace: 1440 bytes
[ 0.093063] Booting paravirtualized kernel on bare hardware
[ 0.093094] Time: 20:07:11 Date: 11/19/08
[ 0.093094] NET: Registered protocol family 16
[ 0.093094] No dock devices found.
[ 0.093094] ACPI: bus type pci registered
[ 0.093998] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 3
[ 0.094002] PCI: MCFG area at e0000000 reserved in E820
[ 0.094080] PCI: Using MMCONFIG at e0000000 - e03fffff
[ 0.094082] PCI: Using configuration type 1 for base access
[ 0.096075] ACPI: EC: Look up EC in DSDT
[ 0.098869] ACPI: Interpreter enabled
[ 0.098873] ACPI: (supports S0 S1 S4 S5)
[ 0.098882] ACPI: Using IOAPIC for interrupt routing
[ 0.101140] ACPI: Device [FDC] status [00000008]: functional but not present; setting present
[ 0.101140] ACPI: Device [LPT] status [00000008]: functional but not present; setting present
[ 0.101140] ACPI: Device [ECP] status [00000008]: functional but not present; setting present
[ 0.102067] ACPI: Device [KCS1] status [00000008]: functional but not present; setting present
[ 0.102067] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.102067] PCI: 0000:00:1a.0 reg 20 io port: [1820, 183f]
[ 0.102103] PCI: 0000:00:1a.1 reg 20 io port: [1840, 185f]
[ 0.102149] PCI: 0000:00:1a.2 reg 20 io port: [1860, 187f]
[ 0.102199] PCI: 0000:00:1a.7 reg 10 32bit mmio: [dfc00800, dfc00bff]
[ 0.102235] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.102240] pci 0000:00:1a.7: PME# disabled
[ 0.102276] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.102279] pci 0000:00:1c.0: PME# disabled
[ 0.102316] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.102319] pci 0000:00:1c.4: PME# disabled
[ 0.102354] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.102358] pci 0000:00:1c.5: PME# disabled
[ 0.102391] PCI: 0000:00:1d.0 reg 20 io port: [1880, 189f]
[ 0.102437] PCI: 0000:00:1d.1 reg 20 io port: [18a0, 18bf]
[ 0.102484] PCI: 0000:00:1d.2 reg 20 io port: [18c0, 18df]
[ 0.102533] PCI: 0000:00:1d.7 reg 10 32bit mmio: [dfc00c00, dfc00fff]
[ 0.102569] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.102574] pci 0000:00:1d.7: PME# disabled
[ 0.103068] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.103072] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 0.103107] PCI: 0000:00:1f.2 reg 10 io port: [1c50, 1c57]
[ 0.103111] PCI: 0000:00:1f.2 reg 14 io port: [1c44, 1c47]
[ 0.103115] PCI: 0000:00:1f.2 reg 18 io port: [1c48, 1c4f]
[ 0.103118] PCI: 0000:00:1f.2 reg 1c io port: [1c40, 1c43]
[ 0.103122] PCI: 0000:00:1f.2 reg 20 io port: [18e0, 18ff]
[ 0.103126] PCI: 0000:00:1f.2 reg 24 32bit mmio: [dfc00000, dfc007ff]
[ 0.103143] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.103146] pci 0000:00:1f.2: PME# disabled
[ 0.103161] PCI: 0000:00:1f.3 reg 10 64bit mmio: [dfc01000, dfc010ff]
[ 0.103170] PCI: 0000:00:1f.3 reg 20 io port: [1c00, 1c1f]
[ 0.103209] PCI: bridge 0000:00:1c.0 io port: [0, fff]
[ 0.103212] PCI: bridge 0000:00:1c.0 32bit mmio: [0, fffff]
[ 0.103216] PCI: bridge 0000:00:1c.0 64bit mmio pref: [0, fffff]
[ 0.103270] PCI: 0000:02:00.0 reg 10 64bit mmio: [df900000, df90ffff]
[ 0.103313] pci 0000:02:00.0: PME# supported from D3hot D3cold
[ 0.103317] pci 0000:02:00.0: PME# disabled
[ 0.103343] PCI: bridge 0000:00:1c.4 32bit mmio: [df900000, df9fffff]
[ 0.103387] PCI: 0000:03:00.0 reg 10 32bit mmio: [de000000, deffffff]
[ 0.103395] PCI: 0000:03:00.0 reg 14 32bit mmio: [df800000, df803fff]
[ 0.103403] PCI: 0000:03:00.0 reg 18 32bit mmio: [df000000, df7fffff]
[ 0.103477] PCI: bridge 0000:00:1c.5 32bit mmio: [df000000, df8fffff]
[ 0.103481] PCI: bridge 0000:00:1c.5 64bit mmio pref: [de000000, deffffff]
[ 0.103518] pci 0000:00:1e.0: transparent bridge
[ 0.103538] bus 00 -> node 0
[ 0.103541] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.103827] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PESA._PRT]
[ 0.103910] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PESB._PRT]
[ 0.103998] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PESC._PRT]
[ 0.104090] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIH._PRT]
[ 0.105068] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 7 9 *10 11 12 14 15)
[ 0.106024] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 7 9 10 *11 12 14 15)
[ 0.106097] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 7 *9 10 11 12 14 15)
[ 0.106160] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled.
[ 0.106225] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled.
[ 0.106289] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled.
[ 0.106353] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled.
[ 0.106417] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled.
[ 0.106456] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.106456] pnp: PnP ACPI init
[ 0.106456] ACPI: bus type pnp registered
[ 0.106456] pnp 00:00: parse allocated resources
[ 0.106456] pnp 00:00: add mem 0xe0000000-0xefffffff flags 0x1
[ 0.106456] pnp 00:00: PNP0c02: calling quirk_system_pci_resources+0x0/0x182
[ 0.106456] pnp 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.106456] pnp 00:01: parse allocated resources
[ 0.107458] pnp 00:01: add io 0xcf8-0xcff flags 0x1
[ 0.107482] pnp 00:01: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.107482] pnp 00:02: parse allocated resources
[ 0.107482] pnp 00:02: add mem 0xfed40000-0xfed44fff flags 0x1
[ 0.107482] pnp 00:02: Plug and Play ACPI device, IDs IFX0102 PNP0c31 (active)
[ 0.107482] pnp 00:03: parse allocated resources
[ 0.107482] pnp 00:03: add mem 0xffb00000-0xffbfffff flags 0x0
[ 0.107482] pnp 00:03: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.107482] pnp 00:04: parse allocated resources
[ 0.107482] pnp 00:04: add io 0x10-0x1f flags 0x1
[ 0.107482] pnp 00:04: add io 0x22-0x2d flags 0x1
[ 0.107482] pnp 00:04: add io 0x2e-0x2f flags 0x1
[ 0.107482] pnp 00:04: add io 0x30-0x3f flags 0x1
[ 0.107482] pnp 00:04: add io 0x4e-0x4f flags 0x1
[ 0.107482] pnp 00:04: add io 0x50-0x53 flags 0x1
[ 0.107482] pnp 00:04: add io 0x62-0x63 flags 0x1
[ 0.107482] pnp 00:04: add io 0x65-0x6f flags 0x1
[ 0.107482] pnp 00:04: add io 0x72-0x73 flags 0x1
[ 0.107482] pnp 00:04: add io 0x74-0x7f flags 0x1
[ 0.107482] pnp 00:04: add io 0x90-0x9f flags 0x1
[ 0.107482] pnp 00:04: add io 0xa2-0xb1 flags 0x1
[ 0.107482] pnp 00:04: add io 0xb2-0xb3 flags 0x1
[ 0.107482] pnp 00:04: add io 0xb4-0xbf flags 0x1
[ 0.107482] pnp 00:04: add io 0xec-0xef flags 0x1
[ 0.107482] pnp 00:04: add io 0x400-0x40f flags 0x1
[ 0.107482] pnp 00:04: add io 0x4d0-0x4d1 flags 0x1
[ 0.107482] pnp 00:04: add io 0x500-0x57f flags 0x1
[ 0.107482] pnp 00:04: add io 0x800-0x80f flags 0x1
[ 0.107482] pnp 00:04: add io 0xca0-0xca1 flags 0x1
[ 0.107482] pnp 00:04: add io 0xca4-0xca7 flags 0x1
[ 0.107482] pnp 00:04: add io 0xcae-0xcaf flags 0x1
[ 0.107482] pnp 00:04: add io 0xe00-0xe7f flags 0x1
[ 0.107482] pnp 00:04: add io 0x1000-0x107f flags 0x1
[ 0.107482] pnp 00:04: add io 0x1100-0x110f flags 0x1
[ 0.107482] pnp 00:04: add io 0x1180-0x11bf flags 0x1
[ 0.107482] pnp 00:04: add io 0xfe00-0xfe00 flags 0x1
[ 0.107482] pnp 00:04: add io 0xff00-0xff00 flags 0x1
[ 0.107482] pnp 00:04: add mem 0xfec00000-0xfecfffff flags 0x0
[ 0.107482] pnp 00:04: add mem 0xfee00000-0xfeefffff flags 0x0
[ 0.107482] pnp 00:04: add mem 0xfed1c000-0xfed1ffff flags 0x1
[ 0.107482] pnp 00:04: add mem 0xfed13000-0xfed13fff flags 0x1
[ 0.107482] pnp 00:04: add mem 0xe0000000-0xefffffff flags 0x1
[ 0.107482] pnp 00:04: add mem 0xfed19000-0xfed19fff flags 0x1
[ 0.107482] pnp 00:04: add mem 0xfed14000-0xfed17fff flags 0x1
[ 0.107482] pnp 00:04: add mem 0xfed18000-0xfed18fff flags 0x1
[ 0.107482] pnp 00:04: PNP0c02: calling quirk_system_pci_resources+0x0/0x182
[ 0.107482] pnp 00:04: io resource (0x10-0x1f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x22-0x2d) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x2e-0x2f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x30-0x3f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x4e-0x4f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x50-0x53) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x62-0x63) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x65-0x6f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x72-0x73) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x74-0x7f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x90-0x9f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0xa2-0xb1) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0xb2-0xb3) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0xb4-0xbf) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0xec-0xef) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x400-0x40f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x4d0-0x4d1) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x500-0x57f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107482] pnp 00:04: io resource (0x800-0x80f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107985] pnp 00:04: io resource (0xca0-0xca1) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107988] pnp 00:04: io resource (0xca4-0xca7) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107992] pnp 00:04: io resource (0xcae-0xcaf) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.107995] pnp 00:04: io resource (0xe00-0xe7f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xfff), disabling
[ 0.108042] pnp 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.108042] pnp 00:05: parse allocated resources
[ 0.108042] pnp 00:05: add io 0x0-0xf flags 0x1
[ 0.108042] pnp 00:05: add io 0x80-0x8f flags 0x1
[ 0.108042] pnp 00:05: add io 0xc0-0xdf flags 0x1
[ 0.108042] pnp 00:05: add dma 4 flags 0x2
[ 0.108042] pnp 00:05: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.108042] pnp 00:06: parse allocated resources
[ 0.108042] pnp 00:06: add io 0x70-0x71 flags 0x1
[ 0.108042] pnp 00:06: add irq 8 flags 0x1
[ 0.108042] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.108042] pnp 00:07: parse allocated resources
[ 0.108042] pnp 00:07: add io 0xf0-0xfe flags 0x1
[ 0.108042] pnp 00:07: add irq 13 flags 0x1
[ 0.108042] pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.108042] pnp 00:08: parse allocated resources
[ 0.108042] pnp 00:08: add io 0x61-0x61 flags 0x1
[ 0.108042] pnp 00:08: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.108042] pnp 00:09: parse allocated resources
[ 0.108064] pnp 00:09: add mem 0xfed00000-0xfed003ff flags 0x1
[ 0.108084] pnp 00:09: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.108084] pnp 00:0a: parse allocated resources
[ 0.108084] pnp 00:0a: add io 0x60-0x60 flags 0x1
[ 0.108084] pnp 00:0a: add io 0x64-0x64 flags 0x1
[ 0.108084] pnp 00:0a: add irq 1 flags 0x1
[ 0.108084] pnp 00:0a: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.108084] pnp 00:0b: parse allocated resources
[ 0.108084] pnp 00:0b: add irq 12 flags 0x1
[ 0.108084] pnp 00:0b: Plug and Play ACPI device, IDs PNP0f13 (active)
[ 0.108084] pnp 00:0c: parse resource options
[ 0.108084] pnp 00:0c: independent io min 0x3f0 max 0x3f0 align 1 size 6 flags 0x1
[ 0.108084] pnp 00:0c: independent io min 0x3f7 max 0x3f7 align 1 size 1 flags 0x1
[ 0.108084] pnp 00:0c: independent dma 2 (bitmask 0x4) flags 0x2
[ 0.108084] pnp 00:0c: independent irq 6 flags 0x1
[ 0.108084] pnp 00:0c: Plug and Play ACPI device, IDs PNP0700 (disabled)
[ 0.108084] pnp 00:0d: parse resource options
[ 0.108102] pnp 00:0d: dependent set 0 (preferred) io min 0x378 max 0x378 align 4 size 4 flags 0x1
[ 0.108105] pnp 00:0d: dependent set 0 (preferred) irq 7 flags 0x1
[ 0.108107] pnp 00:0d: dependent set 1 (acceptable) io min 0x278 max 0x278 align 4 size 4 flags 0x1
[ 0.108109] pnp 00:0d: dependent set 1 (acceptable) irq 5 flags 0x1
[ 0.108111] pnp 00:0d: dependent set 2 (functional) io min 0x3bc max 0x3bc align 4 size 4 flags 0x1
[ 0.108114] pnp 00:0d: dependent set 2 (functional) irq 7 flags 0x1
[ 0.108135] pnp 00:0d: Plug and Play ACPI device, IDs PNP0400 (disabled)
[ 0.108135] pnp 00:0e: parse resource options
[ 0.108135] pnp 00:0e: dependent set 0 (preferred) io min 0x378 max 0x378 align 4 size 4 flags 0x1
[ 0.108135] pnp 00:0e: dependent set 0 (preferred) io min 0x778 max 0x778 align 4 size 4 flags 0x1
[ 0.108135] pnp 00:0e: dependent set 0 (preferred) irq 5 7 flags 0x1
[ 0.108135] pnp 00:0e: dependent set 0 (preferred) dma 1 3 (bitmask 0xa) flags 0x2
[ 0.108135] pnp 00:0e: dependent set 1 (acceptable) io min 0x278 max 0x278 align 4 size 4 flags 0x1
[ 0.108135] pnp 00:0e: dependent set 1 (acceptable) io min 0x678 max 0x678 align 4 size 4 flags 0x1
[ 0.108135] pnp 00:0e: dependent set 1 (acceptable) irq 5 7 flags 0x1
[ 0.108135] pnp 00:0e: dependent set 1 (acceptable) dma 1 3 (bitmask 0xa) flags 0x2
[ 0.108135] pnp 00:0e: Plug and Play ACPI device, IDs PNP0401 (disabled)
[ 0.108986] pnp 00:0f: parse allocated resources
[ 0.109116] pnp 00:0f: add io 0x3f8-0x3ff flags 0x1
[ 0.109120] pnp 00:0f: add irq 4 flags 0x1
[ 0.109121] pnp 00:0f: parse resource options
[ 0.109125] pnp 00:0f: dependent set 0 (preferred) io min 0x3f8 max 0x3f8 align 8 size 8 flags 0x1
[ 0.109128] pnp 00:0f: dependent set 0 (preferred) irq 4 flags 0x1
[ 0.109130] pnp 00:0f: dependent set 1 (acceptable) io min 0x3e8 max 0x3e8 align 8 size 8 flags 0x1
[ 0.109132] pnp 00:0f: dependent set 1 (acceptable) irq 4 flags 0x1
[ 0.109134] pnp 00:0f: dependent set 2 (functional) io min 0x2f8 max 0x2f8 align 8 size 8 flags 0x1
[ 0.109136] pnp 00:0f: dependent set 2 (functional) irq 3 flags 0x1
[ 0.109138] pnp 00:0f: dependent set 3 (functional) io min 0x2e8 max 0x2e8 align 8 size 8 flags 0x1
[ 0.109141] pnp 00:0f: dependent set 3 (functional) irq 3 flags 0x1
[ 0.109163] pnp 00:0f: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.109163] pnp 00:10: parse allocated resources
[ 0.109186] pnp 00:10: add io 0x2f8-0x2ff flags 0x1
[ 0.109189] pnp 00:10: add irq 3 flags 0x1
[ 0.109190] pnp 00:10: parse resource options
[ 0.109195] pnp 00:10: dependent set 0 (preferred) io min 0x2f8 max 0x2f8 align 8 size 8 flags 0x1
[ 0.109197] pnp 00:10: dependent set 0 (preferred) irq 3 flags 0x1
[ 0.109199] pnp 00:10: dependent set 1 (acceptable) io min 0x2e8 max 0x2e8 align 8 size 8 flags 0x1
[ 0.109201] pnp 00:10: dependent set 1 (acceptable) irq 3 flags 0x1
[ 0.109203] pnp 00:10: dependent set 2 (functional) io min 0x3f8 max 0x3f8 align 8 size 8 flags 0x1
[ 0.109206] pnp 00:10: dependent set 2 (functional) irq 4 flags 0x1
[ 0.109208] pnp 00:10: dependent set 3 (functional) io min 0x3e8 max 0x3e8 align 8 size 8 flags 0x1
[ 0.109210] pnp 00:10: dependent set 3 (functional) irq 4 flags 0x1
[ 0.109232] pnp 00:10: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.109232] pnp 00:11: parse allocated resources
[ 0.109232] pnp 00:11: add io 0xca2-0xca3 flags 0x1
[ 0.109232] pnp 00:11: Plug and Play ACPI device, IDs IPI0001 (active)
[ 0.109232] pnp 00:12: PNP0c02: calling quirk_system_pci_resources+0x0/0x182
[ 0.109232] pnp 00:12: Plug and Play ACPI device, IDs PNP0c02 (disabled)
[ 0.109232] pnp: PnP ACPI: found 19 devices
[ 0.109232] ACPI: ACPI bus type pnp unregistered
[ 0.109232] SCSI subsystem initialized
[ 0.109232] libata version 3.00 loaded.
[ 0.109232] usbcore: registered new interface driver usbfs
[ 0.109232] usbcore: registered new interface driver hub
[ 0.109232] usbcore: registered new device driver usb
[ 0.109999] PCI: Using ACPI for IRQ routing
[ 0.109999] pci 0000:00:1c.0: BAR 7: can't allocate resource
[ 0.109999] pci 0000:00:1c.0: BAR 8: can't allocate resource
[ 0.109999] pci 0000:00:1c.0: BAR 9: can't allocate resource
[ 0.121001] PCI-GART: No AMD northbridge found.
[ 0.121007] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.121013] hpet0: 4 64-bit timers, 14318180 Hz
[ 0.121998] ACPI: RTC can wake from S4
[ 0.126988] pnp: the driver 'system' has been registered
[ 0.126996] system 00:00: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.127000] system 00:00: driver attached
[ 0.127008] system 00:04: ioport range 0x1000-0x107f has been reserved
[ 0.127012] system 00:04: ioport range 0x1100-0x110f has been reserved
[ 0.127016] system 00:04: ioport range 0x1180-0x11bf has been reserved
[ 0.127020] system 00:04: ioport range 0xfe00-0xfe00 has been reserved
[ 0.127024] system 00:04: ioport range 0xff00-0xff00 has been reserved
[ 0.127029] system 00:04: iomem range 0xfec00000-0xfecfffff could not be reserved
[ 0.127034] system 00:04: iomem range 0xfee00000-0xfeefffff could not be reserved
[ 0.127039] system 00:04: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.127043] system 00:04: iomem range 0xfed13000-0xfed13fff has been reserved
[ 0.127047] system 00:04: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.127052] system 00:04: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.127057] system 00:04: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.127061] system 00:04: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.127064] system 00:04: driver attached
[ 0.127074] system 00:12: driver attached
[ 0.131703] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
[ 0.131706] pci 0000:00:1c.0: IO window: disabled
[ 0.131710] pci 0000:00:1c.0: MEM window: disabled
[ 0.131713] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.131718] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:02
[ 0.131720] pci 0000:00:1c.4: IO window: disabled
[ 0.131724] pci 0000:00:1c.4: MEM window: 0xdf900000-0xdf9fffff
[ 0.131728] pci 0000:00:1c.4: PREFETCH window: disabled
[ 0.131733] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:03
[ 0.131735] pci 0000:00:1c.5: IO window: disabled
[ 0.131739] pci 0000:00:1c.5: MEM window: 0xdf000000-0xdf8fffff
[ 0.131743] pci 0000:00:1c.5: PREFETCH window: 0x000000de000000-0x000000deffffff
[ 0.131749] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04
[ 0.131751] pci 0000:00:1e.0: IO window: disabled
[ 0.131755] pci 0000:00:1e.0: MEM window: disabled
[ 0.131758] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.131769] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.131773] pci 0000:00:1c.0: setting latency timer to 64
[ 0.131778] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.131782] pci 0000:00:1c.4: setting latency timer to 64
[ 0.131787] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.131790] pci 0000:00:1c.5: setting latency timer to 64
[ 0.131795] pci 0000:00:1e.0: setting latency timer to 64
[ 0.131797] bus: 00 index 0 io port: [0, ffff]
[ 0.131799] bus: 00 index 1 mmio: [0, ffffffffffffffff]
[ 0.131801] bus: 01 index 0 mmio: [0, fff]
[ 0.131803] bus: 01 index 1 mmio: [0, fffff]
[ 0.131805] bus: 01 index 2 mmio: [0, fffff]
[ 0.131807] bus: 01 index 3 mmio: [0, 0]
[ 0.131809] bus: 02 index 0 mmio: [0, 0]
[ 0.131811] bus: 02 index 1 mmio: [df900000, df9fffff]
[ 0.131813] bus: 02 index 2 mmio: [0, 0]
[ 0.131814] bus: 02 index 3 mmio: [0, 0]
[ 0.131816] bus: 03 index 0 mmio: [0, 0]
[ 0.131818] bus: 03 index 1 mmio: [df000000, df8fffff]
[ 0.131820] bus: 03 index 2 mmio: [de000000, deffffff]
[ 0.131822] bus: 03 index 3 mmio: [0, 0]
[ 0.131824] bus: 04 index 0 mmio: [0, 0]
[ 0.131826] bus: 04 index 1 mmio: [0, 0]
[ 0.131828] bus: 04 index 2 mmio: [0, 0]
[ 0.131830] bus: 04 index 3 io port: [0, ffff]
[ 0.131832] bus: 04 index 4 mmio: [0, ffffffffffffffff]
[ 0.131838] NET: Registered protocol family 2
[ 0.141028] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.141374] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.142583] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.143111] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.143114] TCP reno registered
[ 0.146057] NET: Registered protocol family 1
[ 0.146169] Simple Boot Flag at 0x44 set to 0x1
[ 0.146604] IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
[ 0.146879] audit: initializing netlink socket (disabled)
[ 0.146893] type=2000 audit(1227125230.145:1): initialized
[ 0.147323] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.148781] DLM (built Nov 19 2008 20:59:16) installed
[ 0.149215] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.149296] NTFS driver 2.1.29 [Flags: R/W].
[ 0.149455] JFS: nTxBlock = 8192, nTxLock = 65536
[ 0.152993] msgmni has been set to 11891
[ 0.153188] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.153192] io scheduler noop registered
[ 0.153194] io scheduler anticipatory registered
[ 0.153196] io scheduler deadline registered
[ 0.153234] io scheduler cfq registered (default)
[ 0.153248] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x003b
[ 0.153249] pci 0000:00:1a.0: Performing full reset
[ 0.153262] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010
[ 0.153263] pci 0000:00:1a.1: Performing full reset
[ 0.153276] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010
[ 0.153277] pci 0000:00:1a.2: Performing full reset
[ 0.153309] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x003b
[ 0.153310] pci 0000:00:1d.0: Performing full reset
[ 0.153323] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010
[ 0.153324] pci 0000:00:1d.1: Performing full reset
[ 0.153336] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010
[ 0.153337] pci 0000:00:1d.2: Performing full reset
[ 0.153363] pci 0000:03:00.0: Boot video device
[ 0.153423] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.153448] pcieport-driver 0000:00:1c.0: found MSI capability
[ 0.153475] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 0.153499] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 0.153519] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 0.153572] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 0.153594] pcieport-driver 0000:00:1c.4: found MSI capability
[ 0.153618] pci_express 0000:00:1c.4:pcie00: allocate port service
[ 0.153642] pci_express 0000:00:1c.4:pcie02: allocate port service
[ 0.153662] pci_express 0000:00:1c.4:pcie03: allocate port service
[ 0.153716] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[ 0.153738] pcieport-driver 0000:00:1c.5: found MSI capability
[ 0.153762] pci_express 0000:00:1c.5:pcie00: allocate port service
[ 0.153783] pci_express 0000:00:1c.5:pcie02: allocate port service
[ 0.153803] pci_express 0000:00:1c.5:pcie03: allocate port service
[ 0.155559] hpet_resources: 0xfed00000 is busy
[ 0.155614] Non-volatile memory driver v1.2
[ 0.155658] Linux agpgart interface v0.103
[ 0.155703] ipmi message handler version 39.2
[ 0.155707] ipmi device interface
[ 0.155746] IPMI System Interface driver.
[ 0.155750] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca2, slave address 0x20, irq 0
[ 0.184497] ipmi: Found new BMC (man_id: 0x002880, prod_id: 0x0226, dev_id: 0x02)
[ 0.184526] IPMI kcs interface initialized
[ 0.185777] IPMI Watchdog: driver initialized
[ 0.185780] Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot.
[ 0.187688] IPMI poweroff: ATCA Detect mfg 0x2880 prod 0x226
[ 0.187691] IPMI poweroff: Found a chassis style poweroff function
[ 0.187694] pnp: the driver 'tpm_tis' has been registered
[ 0.187736] tpm_tis 00:02: 1.2 TPM (device-id 0xB, rev-id 16)
[ 0.289515] tpm_tis 00:02: driver attached
[ 0.289738] vesafb: framebuffer at 0xde000000, mapped to 0xffffc20000a80000, using 5120k, total 8128k
[ 0.289741] vesafb: mode is 1280x1024x16, linelength=2560, pages=2
[ 0.289743] vesafb: scrolling: redraw
[ 0.289746] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.479449] Console: switching to colour frame buffer device 160x64
[ 0.500489] Switched to high resolution mode on CPU 1
[ 0.501043] Switched to high resolution mode on CPU 0
[ 0.657494] fb0: VESA VGA frame buffer device
[ 0.658556] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.662256] ACPI: Power Button (FF) [PWRF]
[ 0.663170] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.667255] ACPI: Power Button (CM) [PWRB]
[ 0.668273] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 0.669462] processor ACPI0007:00: registered as cooling_device0
[ 0.670776] ACPI: CPU1 (power states: C1[C1] C2[C2])
[ 0.671964] processor ACPI0007:01: registered as cooling_device1
[ 0.674347] [drm] Initialized drm 1.1.0 20060810
[ 0.675331] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 0.920366] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.165365] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.166740] pnp: the driver 'serial' has been registered
[ 1.166935] 00:0f: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.168147] serial 00:0f: driver attached
[ 1.168253] 00:10: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.169462] serial 00:10: driver attached
[ 1.170288] brd: module loaded
[ 1.171339] loop: module loaded
[ 1.172032] tg3.c:v3.94 (August 14, 2008)
[ 1.172892] tg3 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.174327] tg3 0000:02:00.0: setting latency timer to 64
[ 1.182412] eth0: Tigon3 [partno(BCM95755) rev a002 PHY(5755)] (PCI Express) 10/100/1000Base-T Ethernet 00:19:99:42:55:c0
[ 1.184747] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 1.186339] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.187566] PPP generic driver version 2.4.2
[ 1.188515] NET: Registered protocol family 24
[ 1.189568] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 1.191145] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 1.192667] Driver 'sd' needs updating - please use bus_type methods
[ 1.194036] Driver 'sr' needs updating - please use bus_type methods
[ 1.195423] SCSI Media Changer driver v0.25
[ 1.196347] Driver 'ch' needs updating - please use bus_type methods
[ 1.197715] Driver 'ses' needs updating - please use bus_type methods
[ 1.199115] ahci 0000:00:1f.2: version 3.0
[ 1.199121] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.200642] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports ? Gbps 0x3f impl SATA mode
[ 1.202384] ahci 0000:00:1f.2: flags: 64bit led pio ems
[ 1.240361] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.240647] scsi0 : ahci
[ 1.278876] scsi1 : ahci
[ 1.317218] scsi2 : ahci
[ 1.355673] scsi3 : ahci
[ 1.394238] scsi4 : ahci
[ 1.432912] scsi5 : ahci
[ 1.471753] ata1: SATA max UDMA/133 abar m2048@0xdfc00000 port 0xdfc00100 irq 380
[ 1.512778] ata2: SATA max UDMA/133 abar m2048@0xdfc00000 port 0xdfc00180 irq 380
[ 1.553931] ata3: SATA max UDMA/133 abar m2048@0xdfc00000 port 0xdfc00200 irq 380
[ 1.595229] ata4: SATA max UDMA/133 abar m2048@0xdfc00000 port 0xdfc00280 irq 380
[ 1.636656] ata5: SATA max UDMA/133 abar m2048@0xdfc00000 port 0xdfc00300 irq 380
[ 1.678247] ata6: SATA max UDMA/133 abar m2048@0xdfc00000 port 0xdfc00380 irq 380
[ 2.025021] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.125420] ata1.00: ATA-7: ST3160815AS, 4.AAA, max UDMA/133
[ 2.168811] ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 2.242042] ata1.00: configured for UDMA/133
[ 3.010012] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.103217] ata2.00: ATA-7: ST3160815AS, 4.AAA, max UDMA/133
[ 3.150471] ata2.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 3.228175] ata2.00: configured for UDMA/133
[ 4.000263] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.053242] ata3.00: ATA-8: ST31000340AS, SD15, max UDMA/133
[ 4.104342] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 4.158570] ata3.00: configured for UDMA/133
[ 4.933012] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.986530] ata4.00: ATA-8: ST31000340AS, SD15, max UDMA/133
[ 5.037949] ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 5.091145] ata4.00: configured for UDMA/133
[ 5.864261] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 5.914941] ata5.00: ATAPI: HL-DT-STDVD-ROM DH10N, 0F03, max UDMA/100
[ 5.966289] ata5.00: configured for UDMA/100
[ 6.321011] ata6: SATA link down (SStatus 0 SControl 300)
[ 6.370930] scsi 0:0:0:0: Direct-Access ATA ST3160815AS 4.AA PQ: 0 ANSI: 5
[ 6.421674] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 6.472472] sd 0:0:0:0: [sda] Write Protect is off
[ 6.522589] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.522604] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.573815] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 6.625717] sd 0:0:0:0: [sda] Write Protect is off
[ 6.677055] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.677071] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.730242] sda: sda1 sda2 sda3 sda4
[ 6.814125] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.867422] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 6.920908] scsi 1:0:0:0: Direct-Access ATA ST3160815AS 4.AA PQ: 0 ANSI: 5
[ 6.975224] sd 1:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
[ 7.028591] sd 1:0:0:0: [sdb] Write Protect is off
[ 7.080520] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 7.080538] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.133275] sd 1:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
[ 7.186028] sd 1:0:0:0: [sdb] Write Protect is off
[ 7.238512] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 7.238530] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.291868] sdb: sdb1 sdb2 sdb3 sdb4
[ 7.377151] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 7.429520] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 7.482586] scsi 2:0:0:0: Direct-Access ATA ST31000340AS SD15 PQ: 0 ANSI: 5
[ 7.536384] sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
[ 7.590182] sd 2:0:0:0: [sdc] Write Protect is off
[ 7.643390] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 7.643414] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.697508] sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
[ 7.751341] sd 2:0:0:0: [sdc] Write Protect is off
[ 7.804566] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 7.804583] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.859052] sdc: sdc1 sdc2 sdc3 sdc4
[ 7.933982] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 7.989534] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 8.045750] scsi 3:0:0:0: Direct-Access ATA ST31000340AS SD15 PQ: 0 ANSI: 5
[ 8.103695] sd 3:0:0:0: [sdd] 1953525168 512-byte hardware sectors (1000205 MB)
[ 8.162578] sd 3:0:0:0: [sdd] Write Protect is off
[ 8.220636] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 8.220653] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.280632] sd 3:0:0:0: [sdd] 1953525168 512-byte hardware sectors (1000205 MB)
[ 8.341293] sd 3:0:0:0: [sdd] Write Protect is off
[ 8.341294] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 8.341308] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.341309] sdd: sdd1 sdd2 sdd3 sdd4
[ 8.527997] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 8.590734] sd 3:0:0:0: Attached scsi generic sg3 type 0
[ 8.654699] scsi 4:0:0:0: CD-ROM HL-DT-ST DVD-ROM DH10N 0F03 PQ: 0 ANSI: 5
[ 8.721406] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 8.784690] Uniform CD-ROM driver Revision: 3.20
[ 8.847786] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 8.847831] sr 4:0:0:0: Attached scsi generic sg4 type 5
[ 8.910795] sr 4:0:0:0: Embedded Enclosure Device
[ 8.974005] sr 4:0:0:0: Failed to get diagnostic page 0x8000002
[ 9.036493] sr 4:0:0:0: Failed to bind enclosure -19
[ 9.098439] ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
[ 9.098452] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 9.161013] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 9.161016] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 9.222991] drivers/usb/core/inode.c: creating file 'devices'
[ 9.222993] drivers/usb/core/inode.c: creating file '001'
[ 9.223028] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 9.285332] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
[ 9.285334] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr
[ 9.285353] ehci_hcd 0000:00:1a.7: reset command 080022 (park)=0 ithresh=8 Async period=1024 Reset HALT
[ 9.289234] ehci_hcd 0000:00:1a.7: debug port 1
[ 9.350755] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 9.350756] ehci_hcd 0000:00:1a.7: supports USB remote wakeup
[ 9.350764] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xdfc00800
[ 9.412116] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 9.416008] ehci_hcd 0000:00:1a.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
[ 9.422008] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 9.483550] usb usb1: default language 0x0409
[ 9.483574] usb usb1: uevent
[ 9.483593] usb usb1: usb_probe_device
[ 9.483594] usb usb1: configuration #1 chosen from 1 choice
[ 9.545063] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 9.545072] usb 1-0:1.0: uevent
[ 9.545090] hub 1-0:1.0: usb_probe_interface
[ 9.545091] hub 1-0:1.0: usb_probe_interface - got id
[ 9.545093] hub 1-0:1.0: USB hub found
[ 9.606021] hub 1-0:1.0: 6 ports detected
[ 9.666354] hub 1-0:1.0: standalone hub
[ 9.666355] hub 1-0:1.0: no power switching (usb 1.0)
[ 9.666356] hub 1-0:1.0: individual port over-current protection
[ 9.666357] hub 1-0:1.0: power on to power good time: 20ms
[ 9.666360] hub 1-0:1.0: local power source is good
[ 9.666361] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 9.767032] ehci_hcd 0000:00:1a.7: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
[ 9.767035] hub 1-0:1.0: port 2: status 0501 change 0001
[ 9.868045] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 9.868096] drivers/usb/core/inode.c: creating file '001'
[ 9.868139] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 9.868156] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 9.929404] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.929405] usb usb1: Product: EHCI Host Controller
[ 9.929406] usb usb1: Manufacturer: Linux 2.6.27-gentoo-r3 ehci_hcd
[ 9.929407] usb usb1: SerialNumber: 0000:00:1a.7
[ 9.929420] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9.929426] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 9.929428] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 9.929665] ehci_hcd 0000:00:1a.7: port 2 full speed --> companion
[ 9.929667] ehci_hcd 0000:00:1a.7: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
[ 9.929669] hub 1-0:1.0: port 2 not reset yet, waiting 50ms
[ 9.929682] drivers/usb/core/inode.c: creating file '002'
[ 9.929713] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 9.929718] ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8
[ 9.929721] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr
[ 9.929735] ehci_hcd 0000:00:1d.7: reset command 080022 (park)=0 ithresh=8 Async period=1024 Reset HALT
[ 9.933638] ehci_hcd 0000:00:1d.7: debug port 1
[ 9.933643] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 9.933644] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[ 9.933652] ehci_hcd 0000:00:1d.7: irq 16, io mem 0xdfc00c00
[ 9.933655] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 9.937535] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
[ 10.172010] ehci_hcd 0000:00:1a.7: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
[ 10.172025] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0004
[ 10.469014] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 10.527640] usb usb2: default language 0x0409
[ 10.527662] usb usb2: uevent
[ 10.527680] usb usb2: usb_probe_device
[ 10.527681] usb usb2: configuration #1 chosen from 1 choice
[ 10.586609] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 10.586618] usb 2-0:1.0: uevent
[ 10.586636] hub 2-0:1.0: usb_probe_interface
[ 10.586637] hub 2-0:1.0: usb_probe_interface - got id
[ 10.586638] hub 2-0:1.0: USB hub found
[ 10.644827] hub 2-0:1.0: 8 ports detected
[ 10.702181] hub 2-0:1.0: standalone hub
[ 10.702182] hub 2-0:1.0: no power switching (usb 1.0)
[ 10.702182] hub 2-0:1.0: individual port over-current protection
[ 10.702183] hub 2-0:1.0: power on to power good time: 20ms
[ 10.702186] hub 2-0:1.0: local power source is good
[ 10.702187] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 10.803053] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
[ 10.803064] drivers/usb/core/inode.c: creating file '001'
[ 10.803116] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 10.861287] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.919325] usb usb2: Product: EHCI Host Controller
[ 10.919326] usb usb2: Manufacturer: Linux 2.6.27-gentoo-r3 ehci_hcd
[ 10.919327] usb usb2: SerialNumber: 0000:00:1d.7
[ 10.919351] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.919352] ohci_hcd: block sizes: ed 80 td 96
[ 10.919377] USB Universal Host Controller Interface driver v3.0
[ 10.919391] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 10.919396] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 10.919399] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 10.919425] drivers/usb/core/inode.c: creating file '003'
[ 10.919451] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 10.919457] uhci_hcd 0000:00:1a.0: detected 2 ports
[ 10.919461] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 10.919462] uhci_hcd 0000:00:1a.0: Performing full reset
[ 10.919476] uhci_hcd 0000:00:1a.0: supports USB remote wakeup
[ 10.919478] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
[ 10.919507] usb usb3: default language 0x0409
[ 10.919527] usb usb3: uevent
[ 10.919546] usb usb3: usb_probe_device
[ 10.919547] usb usb3: configuration #1 chosen from 1 choice
[ 10.919550] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[ 10.919558] usb 3-0:1.0: uevent
[ 10.919576] hub 3-0:1.0: usb_probe_interface
[ 10.919577] hub 3-0:1.0: usb_probe_interface - got id
[ 10.919578] hub 3-0:1.0: USB hub found
[ 10.919583] hub 3-0:1.0: 2 ports detected
[ 10.919584] hub 3-0:1.0: standalone hub
[ 10.919585] hub 3-0:1.0: no power switching (usb 1.0)
[ 10.919586] hub 3-0:1.0: individual port over-current protection
[ 10.919586] hub 3-0:1.0: power on to power good time: 2ms
[ 10.919588] hub 3-0:1.0: local power source is good
[ 10.919589] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 11.092015] uhci_hcd 0000:00:1a.0: port 2 portsc 0093,00
[ 11.092016] hub 3-0:1.0: port 2: status 0101 change 0001
[ 11.594056] drivers/usb/core/inode.c: creating file '001'
[ 11.594105] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 11.648688] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.702708] usb usb3: Product: UHCI Host Controller
[ 11.756618] usb usb3: Manufacturer: Linux 2.6.27-gentoo-r3 uhci_hcd
[ 11.811267] usb usb3: SerialNumber: 0000:00:1a.0
[ 11.811285] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 11.811290] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 11.811292] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 11.811305] hub 3-0:1.0: state 7 ports 2 chg 0004 evt 0000
[ 11.811312] hub 3-0:1.0: port 2, status 0101, change 0000, 12 Mb/s
[ 11.866034] drivers/usb/core/inode.c: creating file '004'
[ 11.866061] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 11.866067] uhci_hcd 0000:00:1a.1: detected 2 ports
[ 11.866070] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 11.866071] uhci_hcd 0000:00:1a.1: Performing full reset
[ 11.866085] uhci_hcd 0000:00:1a.1: supports USB remote wakeup
[ 11.866093] uhci_hcd 0000:00:1a.1: irq 17, io base 0x00001840
[ 11.866116] usb usb4: default language 0x0409
[ 11.866138] usb usb4: uevent
[ 11.866156] usb usb4: usb_probe_device
[ 11.866157] usb usb4: configuration #1 chosen from 1 choice
[ 11.866159] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[ 11.866168] usb 4-0:1.0: uevent
[ 11.866185] hub 4-0:1.0: usb_probe_interface
[ 11.866186] hub 4-0:1.0: usb_probe_interface - got id
[ 11.866187] hub 4-0:1.0: USB hub found
[ 11.866191] hub 4-0:1.0: 2 ports detected
[ 11.866191] hub 4-0:1.0: standalone hub
[ 11.866192] hub 4-0:1.0: no power switching (usb 1.0)
[ 11.866193] hub 4-0:1.0: individual port over-current protection
[ 11.866194] hub 4-0:1.0: power on to power good time: 2ms
[ 11.866196] hub 4-0:1.0: local power source is good
[ 11.866197] hub 4-0:1.0: trying to enable port power on non-switchable hub
[ 11.973051] drivers/usb/core/inode.c: creating file '001'
[ 11.973086] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 11.973087] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.973088] usb usb4: Product: UHCI Host Controller
[ 11.973089] usb usb4: Manufacturer: Linux 2.6.27-gentoo-r3 uhci_hcd
[ 11.973090] usb usb4: SerialNumber: 0000:00:1a.1
[ 11.973105] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 11.973110] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 11.973113] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 11.973136] drivers/usb/core/inode.c: creating file '005'
[ 11.973168] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 11.973175] uhci_hcd 0000:00:1a.2: detected 2 ports
[ 11.973178] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 11.973179] uhci_hcd 0000:00:1a.2: Performing full reset
[ 11.973193] uhci_hcd 0000:00:1a.2: supports USB remote wakeup
[ 11.973196] uhci_hcd 0000:00:1a.2: irq 18, io base 0x00001860
[ 11.973221] usb usb5: default language 0x0409
[ 11.973243] usb usb5: uevent
[ 11.973261] usb usb5: usb_probe_device
[ 11.973262] usb usb5: configuration #1 chosen from 1 choice
[ 11.973264] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[ 11.973273] usb 5-0:1.0: uevent
[ 11.973290] hub 5-0:1.0: usb_probe_interface
[ 11.973291] hub 5-0:1.0: usb_probe_interface - got id
[ 11.973292] hub 5-0:1.0: USB hub found
[ 11.973296] hub 5-0:1.0: 2 ports detected
[ 11.973296] hub 5-0:1.0: standalone hub
[ 11.973297] hub 5-0:1.0: no power switching (usb 1.0)
[ 11.973298] hub 5-0:1.0: individual port over-current protection
[ 11.973299] hub 5-0:1.0: power on to power good time: 2ms
[ 11.973301] hub 5-0:1.0: local power source is good
[ 11.973302] hub 5-0:1.0: trying to enable port power on non-switchable hub
[ 11.973305] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 12.285083] drivers/usb/core/inode.c: creating file '001'
[ 12.285115] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 12.285116] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 12.285117] usb usb5: Product: UHCI Host Controller
[ 12.285118] usb usb5: Manufacturer: Linux 2.6.27-gentoo-r3 uhci_hcd
[ 12.285119] usb usb5: SerialNumber: 0000:00:1a.2
[ 12.285136] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 12.285141] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 12.285144] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 12.285168] drivers/usb/core/inode.c: creating file '006'
[ 12.285198] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 12.285203] uhci_hcd 0000:00:1d.0: detected 2 ports
[ 12.285207] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 12.285208] uhci_hcd 0000:00:1d.0: Performing full reset
[ 12.285222] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
[ 12.285224] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001880
[ 12.285250] usb usb6: default language 0x0409
[ 12.285270] usb usb6: uevent
[ 12.285288] usb usb6: usb_probe_device
[ 12.285289] usb usb6: configuration #1 chosen from 1 choice
[ 12.285292] usb usb6: adding 6-0:1.0 (config #1, interface 0)
[ 12.285300] usb 6-0:1.0: uevent
[ 12.285320] hub 6-0:1.0: usb_probe_interface
[ 12.285321] hub 6-0:1.0: usb_probe_interface - got id
[ 12.285321] hub 6-0:1.0: USB hub found
[ 12.285325] hub 6-0:1.0: 2 ports detected
[ 12.285326] hub 6-0:1.0: standalone hub
[ 12.285327] hub 6-0:1.0: no power switching (usb 1.0)
[ 12.285328] hub 6-0:1.0: individual port over-current protection
[ 12.285328] hub 6-0:1.0: power on to power good time: 2ms
[ 12.285330] hub 6-0:1.0: local power source is good
[ 12.285331] hub 6-0:1.0: trying to enable port power on non-switchable hub
[ 12.999021] usb usb4: suspend_rh (auto-stop)
[ 12.999051] hub 1-0:1.0: hub_suspend
[ 12.999053] usb usb1: bus auto-suspend
[ 12.999054] ehci_hcd 0000:00:1a.7: suspend root hub
[ 12.999072] hub 2-0:1.0: hub_suspend
[ 12.999073] usb usb2: bus auto-suspend
[ 12.999074] ehci_hcd 0000:00:1d.7: suspend root hub
[ 12.999135] drivers/usb/core/inode.c: creating file '001'
[ 12.999176] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 12.999177] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 12.999178] usb usb6: Product: UHCI Host Controller
[ 12.999179] usb usb6: Manufacturer: Linux 2.6.27-gentoo-r3 uhci_hcd
[ 12.999180] usb usb6: SerialNumber: 0000:00:1d.0
[ 12.999197] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 12.999202] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 12.999204] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 12.999233] drivers/usb/core/inode.c: creating file '007'
[ 12.999266] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 12.999271] uhci_hcd 0000:00:1d.1: detected 2 ports
[ 12.999275] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 12.999276] uhci_hcd 0000:00:1d.1: Performing full reset
[ 12.999291] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
[ 12.999293] uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018a0
[ 12.999319] usb usb7: default language 0x0409
[ 12.999339] usb usb7: uevent
[ 12.999357] usb usb7: usb_probe_device
[ 12.999358] usb usb7: configuration #1 chosen from 1 choice
[ 12.999361] usb usb7: adding 7-0:1.0 (config #1, interface 0)
[ 12.999371] usb 7-0:1.0: uevent
[ 12.999389] hub 7-0:1.0: usb_probe_interface
[ 12.999390] hub 7-0:1.0: usb_probe_interface - got id
[ 12.999391] hub 7-0:1.0: USB hub found
[ 12.999395] hub 7-0:1.0: 2 ports detected
[ 12.999396] hub 7-0:1.0: standalone hub
[ 12.999396] hub 7-0:1.0: no power switching (usb 1.0)
[ 12.999397] hub 7-0:1.0: individual port over-current protection
[ 12.999398] hub 7-0:1.0: power on to power good time: 2ms
[ 12.999400] hub 7-0:1.0: local power source is good
[ 12.999401] hub 7-0:1.0: trying to enable port power on non-switchable hub
[ 13.656028] usb usb5: suspend_rh (auto-stop)
[ 13.656086] drivers/usb/core/inode.c: creating file '001'
[ 13.656121] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 13.656122] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 13.656123] usb usb7: Product: UHCI Host Controller
[ 13.656124] usb usb7: Manufacturer: Linux 2.6.27-gentoo-r3 uhci_hcd
[ 13.656125] usb usb7: SerialNumber: 0000:00:1d.1
[ 13.656140] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 13.656145] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 13.656147] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 13.656175] drivers/usb/core/inode.c: creating file '008'
[ 13.656203] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 13.656209] uhci_hcd 0000:00:1d.2: detected 2 ports
[ 13.656212] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 13.656213] uhci_hcd 0000:00:1d.2: Performing full reset
[ 13.656227] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
[ 13.656230] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0
[ 13.656256] usb usb8: default language 0x0409
[ 13.656278] usb usb8: uevent
[ 13.656295] usb usb8: usb_probe_device
[ 13.656296] usb usb8: configuration #1 chosen from 1 choice
[ 13.656299] usb usb8: adding 8-0:1.0 (config #1, interface 0)
[ 13.656307] usb 8-0:1.0: uevent
[ 13.656326] hub 8-0:1.0: usb_probe_interface
[ 13.656327] hub 8-0:1.0: usb_probe_interface - got id
[ 13.656328] hub 8-0:1.0: USB hub found
[ 13.656335] hub 8-0:1.0: 2 ports detected
[ 13.656336] hub 8-0:1.0: standalone hub
[ 13.656336] hub 8-0:1.0: no power switching (usb 1.0)
[ 13.656337] hub 8-0:1.0: individual port over-current protection
[ 13.656338] hub 8-0:1.0: power on to power good time: 2ms
[ 13.656340] hub 8-0:1.0: local power source is good
[ 13.656341] hub 8-0:1.0: trying to enable port power on non-switchable hub
[ 14.304011] usb usb6: suspend_rh (auto-stop)
[ 14.304086] drivers/usb/core/inode.c: creating file '001'
[ 14.304125] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 14.304127] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 14.304128] usb usb8: Product: UHCI Host Controller
[ 14.304129] usb usb8: Manufacturer: Linux 2.6.27-gentoo-r3 uhci_hcd
[ 14.304129] usb usb8: SerialNumber: 0000:00:1d.2
[ 14.948029] usb usb7: suspend_rh (auto-stop)
[ 15.194352] usb 3-2: skipped 16 descriptors after interface
[ 15.194353] usb 3-2: skipped 2 descriptors after interface
[ 15.194354] usb 3-2: skipped 1 descriptor after endpoint
[ 15.194355] usb 3-2: skipped 2 descriptors after interface
[ 15.194358] usb 3-2: skipped 1 descriptor after endpoint
[ 15.194359] usb 3-2: skipped 2 descriptors after interface
[ 15.194360] usb 3-2: skipped 1 descriptor after endpoint
[ 15.194361] usb 3-2: skipped 1 descriptor after interface
[ 15.198549] usb 3-2: default language 0x0409
[ 15.203576] usb 3-2: uevent
[ 15.203606] usb 3-2: usb_probe_device
[ 15.203608] usb 3-2: configuration #1 chosen from 1 choice
[ 15.255552] usb 3-2: adding 3-2:1.0 (config #1, interface 0)
[ 15.255567] usb 3-2:1.0: uevent
[ 15.255594] usb 3-2: adding 3-2:1.1 (config #1, interface 1)
[ 15.255609] usb 3-2:1.1: uevent
[ 15.255634] usb 3-2: adding 3-2:1.2 (config #1, interface 2)
[ 15.255647] usb 3-2:1.2: uevent
[ 15.255676] usb 3-2: adding 3-2:1.3 (config #1, interface 3)
[ 15.255684] usb 3-2:1.3: uevent
[ 15.255727] drivers/usb/core/inode.c: creating file '002'
[ 15.255761] usb 3-2: New USB device found, idVendor=0ccd, idProduct=0028
[ 15.305735] usb 3-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 15.355590] usb 3-2: Product: USB Audio
[ 15.404983] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 15.404985] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 15.404987] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 15.404988] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 15.404990] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 15.405017] usbcore: registered new interface driver usblp
[ 15.454809] usb usb8: suspend_rh (auto-stop)
[ 15.454827] Initializing USB Mass Storage driver...
[ 15.504252] usbcore: registered new interface driver usb-storage
[ 15.554165] USB Mass Storage support registered.
[ 15.604024] usbcore: registered new interface driver libusual
[ 15.654296] usbcore: registered new interface driver usbserial
[ 15.704275] usbserial: USB Serial support registered for generic
[ 15.754322] usbserial_generic 3-2:1.0: usb_probe_interface
[ 15.754323] usbserial_generic 3-2:1.0: usb_probe_interface - got id
[ 15.754327] usbserial_generic 3-2:1.1: usb_probe_interface
[ 15.754328] usbserial_generic 3-2:1.1: usb_probe_interface - got id
[ 15.754331] usbserial_generic 3-2:1.2: usb_probe_interface
[ 15.754332] usbserial_generic 3-2:1.2: usb_probe_interface - got id
[ 15.754335] usbserial_generic 3-2:1.3: usb_probe_interface
[ 15.754336] usbserial_generic 3-2:1.3: usb_probe_interface - got id
[ 15.754362] usbcore: registered new interface driver usbserial_generic
[ 15.804774] usbserial: USB Serial Driver core
[ 15.855444] pnp: the driver 'i8042 kbd' has been registered
[ 15.855454] i8042 kbd 00:0a: driver attached
[ 15.855477] pnp: the driver 'i8042 aux' has been registered
[ 15.855489] i8042 aux 00:0b: driver attached
[ 15.855509] PNP: PS/2 Controller [PNP0303:KEYB,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 15.909855] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 15.961122] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 16.011829] mice: PS/2 mouse device common for all mice
[ 16.091089] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 16.154292] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 16.568075] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[ 16.630016] pnp: the driver 'rtc_cmos' has been registered
[ 16.630071] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 16.683191] rtc0: alarms up to one month, y3k, hpet irqs
[ 16.736289] rtc_cmos 00:06: driver attached
[ 16.736311] i2c /dev entries driver
[ 16.736356] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 16.760049] coretemp coretemp.0: Using relative temperature scale!
[ 16.789067] coretemp coretemp.1: Using relative temperature scale!
[ 16.799009] md: raid1 personality registered for level 1
[ 16.799047] device-mapper: uevent: version 1.0.3
[ 16.799115] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 16.799124] CAPI Subsystem Rev 1.1.2.8
[ 16.799916] capi20: Rev 1.1.2.7: started up with major 68 (no capifs)
[ 16.799939] b1pci: revision 1.1.2.2
[ 16.799940] b1: revision 1.1.2.2
[ 16.799941] b1dma: revision 1.1.2.3
[ 16.799942] EDAC MC: Ver: 2.1.0 Nov 19 2008
[ 16.800161] cpuidle: using governor ladder
[ 17.019201] cpuidle: using governor menu
[ 17.019242] usbcore: registered new interface driver hiddev
[ 17.019251] usbhid 3-2:1.3: usb_probe_interface
[ 17.019252] usbhid 3-2:1.3: usb_probe_interface - got id
[ 17.020558] Marking TSC unstable due to TSC halts in idle
[ 17.649479] input: USB Audio as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.3/input/input5
[ 17.704673] hub 4-0:1.0: hub_suspend
[ 17.704675] usb usb4: bus auto-suspend
[ 17.704676] usb usb4: suspend_rh
[ 17.704688] hub 5-0:1.0: hub_suspend
[ 17.704690] usb usb5: bus auto-suspend
[ 17.704691] usb usb5: suspend_rh
[ 17.704701] hub 6-0:1.0: hub_suspend
[ 17.704703] usb usb6: bus auto-suspend
[ 17.704703] usb usb6: suspend_rh
[ 17.704714] hub 7-0:1.0: hub_suspend
[ 17.704715] usb usb7: bus auto-suspend
[ 17.704716] usb usb7: suspend_rh
[ 17.704727] hub 8-0:1.0: hub_suspend
[ 17.704729] usb usb8: bus auto-suspend
[ 17.704729] usb usb8: suspend_rh
[ 17.709024] uhci_hcd 0000:00:1a.0: reserve dev 2 ep83-INT, period 32, phase 16, 13 us
[ 17.712110] input,hidraw0: USB HID v1.00 Device [USB Audio] on usb-0000:00:1a.0-2
[ 17.767556] usbcore: registered new interface driver usbhid
[ 17.822932] usbhid: v2.6:USB HID core driver
[ 17.877941] Advanced Linux Sound Architecture Driver Version 1.0.17.
[ 17.933755] snd-usb-audio 3-2:1.0: usb_probe_interface
[ 17.933758] snd-usb-audio 3-2:1.0: usb_probe_interface - got id
[ 18.030986] usbcore: registered new interface driver snd-usb-audio
[ 18.086740] ALSA device list:
[ 18.141671] #0: USB Audio at usb-0000:00:1a.0-2, full speed
[ 18.197479] Netfilter messages via NETLINK v0.30.
[ 18.253206] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 18.309565] ctnetlink v0.93: registering with nfnetlink.
[ 18.366616] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 18.423269] TCP cubic registered
[ 18.479517] Initializing XFRM netlink socket
[ 18.536401] NET: Registered protocol family 10
[ 18.593391] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.650094] IPv6 over IPv4 tunneling driver
[ 18.706756] NET: Registered protocol family 17
[ 18.763100] RPC: Registered udp transport module.
[ 18.819162] RPC: Registered tcp transport module.
[ 18.875513] SCTP: Hash tables configured (established 65536 bind 65536)
[ 18.939217] registered taskstats version 1
[ 18.994859] Magic number: 0:645:144
[ 19.049935] block ram9: hash matches
[ 19.104774] acpi device:15: hash matches
[ 19.159557] md: Autodetecting RAID arrays.
[ 19.476457] md: Scanned 16 and added 16 devices.
[ 19.530579] md: autorun ...
[ 19.584011] md: considering sdd4 ...
[ 19.637814] md: adding sdd4 ...
[ 19.691042] md: sdd3 has different UUID to sdd4
[ 19.744097] md: sdd2 has different UUID to sdd4
[ 19.744099] md: sdd1 has different UUID to sdd4
[ 19.744102] md: adding sdc4 ...
[ 19.744103] md: sdc3 has different UUID to sdd4
[ 19.744105] md: sdc2 has different UUID to sdd4
[ 19.744107] md: sdc1 has different UUID to sdd4
[ 19.744108] md: sdb4 has different UUID to sdd4
[ 19.744110] md: sdb3 has different UUID to sdd4
[ 19.744112] md: sdb2 has different UUID to sdd4
[ 19.744113] md: sdb1 has different UUID to sdd4
[ 19.744115] md: sda4 has different UUID to sdd4
[ 19.744117] md: sda3 has different UUID to sdd4
[ 19.744118] md: sda2 has different UUID to sdd4
[ 19.744120] md: sda1 has different UUID to sdd4
[ 20.388848] md: created md8
[ 20.428248] md: bind<sdc4>
[ 20.467142] md: bind<sdd4>
[ 20.504901] md: running: <sdd4><sdc4>
[ 20.542101] raid1: raid set md8 active with 2 out of 2 mirrors
[ 20.579456] md: considering sdd3 ...
[ 20.616230] md: adding sdd3 ...
[ 20.652948] md: sdd2 has different UUID to sdd3
[ 20.652950] md: sdd1 has different UUID to sdd3
[ 20.652953] md: adding sdc3 ...
[ 20.652954] md: sdc2 has different UUID to sdd3
[ 20.652956] md: sdc1 has different UUID to sdd3
[ 20.652957] md: sdb4 has different UUID to sdd3
[ 20.652959] md: sdb3 has different UUID to sdd3
[ 20.652961] md: sdb2 has different UUID to sdd3
[ 20.652962] md: sdb1 has different UUID to sdd3
[ 20.652964] md: sda4 has different UUID to sdd3
[ 20.652966] md: sda3 has different UUID to sdd3
[ 20.652967] md: sda2 has different UUID to sdd3
[ 20.652969] md: sda1 has different UUID to sdd3
[ 20.653042] md: created md7
[ 20.653043] md: bind<sdc3>
[ 20.653048] md: bind<sdd3>
[ 20.653053] md: running: <sdd3><sdc3>
[ 20.653122] raid1: raid set md7 active with 2 out of 2 mirrors
[ 20.653148] md: considering sdd2 ...
[ 20.653150] md: adding sdd2 ...
[ 20.653152] md: sdd1 has different UUID to sdd2
[ 20.653154] md: adding sdc2 ...
[ 20.653156] md: sdc1 has different UUID to sdd2
[ 20.653158] md: sdb4 has different UUID to sdd2
[ 20.653159] md: sdb3 has different UUID to sdd2
[ 20.653161] md: sdb2 has different UUID to sdd2
[ 20.653163] md: sdb1 has different UUID to sdd2
[ 20.653164] md: sda4 has different UUID to sdd2
[ 20.653166] md: sda3 has different UUID to sdd2
[ 20.653167] md: sda2 has different UUID to sdd2
[ 20.653169] md: sda1 has different UUID to sdd2
[ 20.653232] md: created md6
[ 20.653233] md: bind<sdc2>
[ 20.653237] md: bind<sdd2>
[ 20.653241] md: running: <sdd2><sdc2>
[ 20.653306] raid1: raid set md6 active with 2 out of 2 mirrors
[ 20.653333] md: considering sdd1 ...
[ 20.653336] md: adding sdd1 ...
[ 20.653338] md: adding sdc1 ...
[ 20.653339] md: sdb4 has different UUID to sdd1
[ 20.653341] md: sdb3 has different UUID to sdd1
[ 20.653343] md: sdb2 has different UUID to sdd1
[ 20.653344] md: sdb1 has different UUID to sdd1
[ 20.653346] md: sda4 has different UUID to sdd1
[ 20.653348] md: sda3 has different UUID to sdd1
[ 20.653349] md: sda2 has different UUID to sdd1
[ 20.653351] md: sda1 has different UUID to sdd1
[ 20.653409] md: created md5
[ 20.653410] md: bind<sdc1>
[ 20.653417] md: bind<sdd1>
[ 20.653422] md: running: <sdd1><sdc1>
[ 20.653488] raid1: raid set md5 active with 2 out of 2 mirrors
[ 20.653513] md: considering sdb4 ...
[ 20.653516] md: adding sdb4 ...
[ 20.653517] md: sdb3 has different UUID to sdb4
[ 20.653519] md: sdb2 has different UUID to sdb4
[ 20.653520] md: sdb1 has different UUID to sdb4
[ 20.653523] md: adding sda4 ...
[ 20.653524] md: sda3 has different UUID to sdb4
[ 20.653526] md: sda2 has different UUID to sdb4
[ 20.653528] md: sda1 has different UUID to sdb4
[ 20.653587] md: created md4
[ 20.653588] md: bind<sda4>
[ 20.653593] md: bind<sdb4>
[ 20.653597] md: running: <sdb4><sda4>
[ 20.653662] raid1: raid set md4 active with 2 out of 2 mirrors
[ 20.653688] md: considering sdb3 ...
[ 20.653690] md: adding sdb3 ...
[ 20.653692] md: sdb2 has different UUID to sdb3
[ 20.653694] md: sdb1 has different UUID to sdb3
[ 20.653696] md: adding sda3 ...
[ 20.653698] md: sda2 has different UUID to sdb3
[ 20.653699] md: sda1 has different UUID to sdb3
[ 20.653761] md: created md3
[ 20.653762] md: bind<sda3>
[ 20.653767] md: bind<sdb3>
[ 20.653773] md: running: <sdb3><sda3>
[ 20.653838] raid1: raid set md3 active with 2 out of 2 mirrors
[ 20.653863] md: considering sdb2 ...
[ 20.653865] md: adding sdb2 ...
[ 20.653867] md: sdb1 has different UUID to sdb2
[ 20.653869] md: adding sda2 ...
[ 20.653871] md: sda1 has different UUID to sdb2
[ 20.653931] md: created md2
[ 20.653932] md: bind<sda2>
[ 20.653937] md: bind<sdb2>
[ 20.653941] md: running: <sdb2><sda2>
[ 20.654017] raid1: raid set md2 active with 2 out of 2 mirrors
[ 20.654042] md: considering sdb1 ...
[ 20.654045] md: adding sdb1 ...
[ 20.654047] md: adding sda1 ...
[ 20.654108] md: created md1
[ 20.654109] md: bind<sda1>
[ 20.654114] md: bind<sdb1>
[ 20.654118] md: running: <sdb1><sda1>
[ 20.654185] raid1: raid set md1 active with 2 out of 2 mirrors
[ 20.654211] md: ... autorun DONE.
[ 22.792447] kjournald starting. Commit interval 5 seconds
[ 22.792457] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.792464] VFS: Mounted root (ext3 filesystem) readonly.
[ 22.792476] Freeing unused kernel memory: 452k freed
[ 25.419727] usb usb3: uevent
[ 25.419832] usb 3-0:1.0: uevent
[ 25.420024] usb 3-2: uevent
[ 25.420123] usb 3-2:1.0: uevent
[ 25.420967] usb 3-2:1.1: uevent
[ 25.421082] usb 3-2:1.2: uevent
[ 25.421214] usb 3-2:1.3: uevent
[ 25.422434] usb usb4: uevent
[ 25.422583] usb 4-0:1.0: uevent
[ 25.423593] usb usb5: uevent
[ 25.423772] usb 5-0:1.0: uevent
[ 25.425200] usb usb1: uevent
[ 25.425211] usb 1-0:1.0: uevent
[ 25.425393] usb usb6: uevent
[ 25.425401] usb 6-0:1.0: uevent
[ 25.425447] usb usb7: uevent
[ 25.425455] usb 7-0:1.0: uevent
[ 25.425501] usb usb8: uevent
[ 25.425510] usb 8-0:1.0: uevent
[ 25.425555] usb usb2: uevent
[ 25.425564] usb 2-0:1.0: uevent
[ 30.511321] EXT3 FS on md3, internal journal
[ 30.732985] kjournald starting. Commit interval 5 seconds
[ 30.783879] EXT3 FS on dm-0, internal journal
[ 30.783883] EXT3-fs: mounted filesystem with ordered data mode.
[ 30.974092] kjournald starting. Commit interval 5 seconds
[ 30.974304] EXT3 FS on dm-3, internal journal
[ 30.974307] EXT3-fs: mounted filesystem with ordered data mode.
[ 31.043295] kjournald starting. Commit interval 5 seconds
[ 31.043518] EXT3 FS on dm-4, internal journal
[ 31.043521] EXT3-fs: mounted filesystem with ordered data mode.
[ 31.137418] kjournald starting. Commit interval 5 seconds
[ 31.137619] EXT3 FS on dm-5, internal journal
[ 31.137622] EXT3-fs: mounted filesystem with ordered data mode.
[-- Attachment #3: Type: text/plain, Size: 20 bytes --]
--
Frank Cringle
^ permalink raw reply [flat|nested] 4+ messages in thread