From: Phillip Susi <phill@thesusis.net>
To: Damien Le Moal <dlemoal@kernel.org>
Cc: linux-ide@vger.kernel.org, linux-scsi@vger.kernel.org,
"Martin K . Petersen" <martin.petersen@oracle.com>,
John Garry <john.g.garry@oracle.com>,
Rodrigo Vivi <rodrigo.vivi@intel.com>,
Paul Ausbeck <paula@soe.ucsc.edu>,
Kai-Heng Feng <kai.heng.feng@canonical.com>,
Joe Breuer <linux-kernel@jmbreuer.net>,
Geert Uytterhoeven <geert@linux-m68k.org>,
Chia-Lin Kao <acelan.kao@canonical.com>
Subject: Re: [PATCH v6 19/23] ata: libata-core: Do not resume runtime suspended ports
Date: Tue, 26 Sep 2023 11:01:54 -0400 [thread overview]
Message-ID: <87bkdpdkon.fsf@vps.thesusis.net> (raw)
In-Reply-To: <e3ddb272-4ff6-e5a7-7a4e-cb2acf0595d7@kernel.org>
Damien Le Moal <dlemoal@kernel.org> writes:
> I suspect you are talking about resume from hybernation here, where the drive
> may have been completely powered off... Yes, in such case, the drive will
> spinup, unless you have PUIS and enabled it.
The same thing happens in suspend / S3.
> Sure, but please do not have this delay this patch series. The problem you are
> describing above exists today already. This patch series is not making it worse,
> nor is it trying to solve it. And note that this issue is not just for ATA. SCSI
> devices locally attached to a machine that you hybernate will end up doing the
> same and spinup when power is restored...
You are saying that right now, the sd driver issues a START UNIT command
on system resume ( it looks like there's a flag you can set now to prevent
that ), then leaves the runtime pm state looking like the drive is still
suspended? I thought it handled that correctly but I don't see any code
doing so right now.
If that's the case, then I suppose this series at least does not make
things worse...
next prev parent reply other threads:[~2023-09-26 15:21 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-09-23 0:29 [PATCH v6 00/23] Fix libata suspend/resume handling and code cleanup Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 01/23] ata: libata-core: Fix ata_port_request_pm() locking Damien Le Moal
2023-09-26 17:18 ` Bart Van Assche
2023-09-23 0:29 ` [PATCH v6 02/23] ata: libata-core: Fix port and device removal Damien Le Moal
2023-09-26 17:28 ` Bart Van Assche
2023-09-23 0:29 ` [PATCH v6 03/23] ata: libata-scsi: link ata port and scsi device Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 04/23] scsi: sd: Differentiate system and runtime start/stop management Damien Le Moal
2023-09-26 18:07 ` Bart Van Assche
2023-09-23 0:29 ` [PATCH v6 05/23] ata: libata-scsi: Disable scsi device manage_system_start_stop Damien Le Moal
2023-09-25 14:27 ` Phillip Susi
2023-09-26 6:19 ` Damien Le Moal
2023-09-26 6:34 ` Damien Le Moal
2023-09-26 15:25 ` Phillip Susi
2023-09-23 0:29 ` [PATCH v6 06/23] scsi: Do not attempt to rescan suspended devices Damien Le Moal
2023-09-26 18:10 ` Bart Van Assche
2023-09-23 0:29 ` [PATCH v6 07/23] ata: libata-scsi: Fix delayed scsi_rescan_device() execution Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 08/23] ata: libata-core: Do not register PM operations for SAS ports Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 09/23] scsi: sd: Do not issue commands to suspended disks on shutdown Damien Le Moal
2023-09-25 20:22 ` Bart Van Assche
2023-09-26 6:00 ` Damien Le Moal
2023-09-26 14:51 ` Bart Van Assche
2023-09-26 23:30 ` Bart Van Assche
2023-09-23 0:29 ` [PATCH v6 10/23] ata: libata-core: Fix compilation warning in ata_dev_config_ncq() Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 11/23] ata: libata-eh: Fix compilation warning in ata_eh_link_report() Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 12/23] scsi: Remove scsi device no_start_on_resume flag Damien Le Moal
2023-09-26 20:42 ` Bart Van Assche
2023-09-23 0:29 ` [PATCH v6 13/23] ata: libata-scsi: Cleanup ata_scsi_start_stop_xlat() Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 14/23] ata: libata-core: Synchronize ata_port_detach() with hotplug Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 15/23] ata: libata-core: Detach a port devices on shutdown Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 16/23] ata: libata-core: Remove ata_port_suspend_async() Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 17/23] ata: libata-core: Remove ata_port_resume_async() Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 18/23] ata: libata-core: Do not poweroff runtime suspended ports Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 19/23] ata: libata-core: Do not resume " Damien Le Moal
2023-09-25 17:26 ` Phillip Susi
2023-09-26 6:27 ` Damien Le Moal
2023-09-26 15:01 ` Phillip Susi [this message]
2023-09-23 0:29 ` [PATCH v6 20/23] ata: libata-sata: Improve ata_sas_slave_configure() Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 21/23] ata: libata-eh: Improve reset error messages Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 22/23] ata: libata-eh: Reduce "disable device" message verbosity Damien Le Moal
2023-09-23 0:29 ` [PATCH v6 23/23] ata: libata: Cleanup inline DMA helper functions Damien Le Moal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87bkdpdkon.fsf@vps.thesusis.net \
--to=phill@thesusis.net \
--cc=acelan.kao@canonical.com \
--cc=dlemoal@kernel.org \
--cc=geert@linux-m68k.org \
--cc=john.g.garry@oracle.com \
--cc=kai.heng.feng@canonical.com \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@jmbreuer.net \
--cc=linux-scsi@vger.kernel.org \
--cc=martin.petersen@oracle.com \
--cc=paula@soe.ucsc.edu \
--cc=rodrigo.vivi@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox