From mboxrd@z Thu Jan 1 00:00:00 1970 From: bugme-daemon@bugzilla.kernel.org Subject: [Bug 10436] New: Compact Flash HD: dma and seek_error/badCRC problems Date: Thu, 10 Apr 2008 05:29:18 -0700 (PDT) Message-ID: Return-path: Received: from smtp1.linux-foundation.org ([140.211.169.13]:48406 "EHLO smtp1.linux-foundation.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1753955AbYDJM3s (ORCPT ); Thu, 10 Apr 2008 08:29:48 -0400 Received: from picon.linux-foundation.org (picon.linux-foundation.org [140.211.169.79]) by smtp1.linux-foundation.org (8.14.2/8.13.5/Debian-3ubuntu1.1) with ESMTP id m3ACTIeB004398 for ; Thu, 10 Apr 2008 05:29:19 -0700 Sender: linux-ide-owner@vger.kernel.org List-Id: linux-ide@vger.kernel.org To: linux-ide@vger.kernel.org http://bugzilla.kernel.org/show_bug.cgi?id=10436 Summary: Compact Flash HD: dma and seek_error/badCRC problems Product: IO/Storage Version: 2.5 KernelVersion: 2.6.24.3 / 2.6.24.4 Platform: All OS/Version: Linux Tree: Mainline Status: NEW Severity: normal Priority: P1 Component: IDE AssignedTo: io_ide@kernel-bugs.osdl.org ReportedBy: marco@absence.it Latest working kernel version: 2.6.22 about DMA only Earliest failing kernel version: Distribution: Debian testing (Lenny) Hardware Environment: Mini-ITX VIA EPIA SN Motherboard, Sandisk SDCFX4-8192 Compact Flash (hda), Maxtor PATA HD (hdb) Problem Description: I'm going to report two different problems but maybe related one with the other. I own a VIA SN board that comes with VIA VT8251 South Bridge (that includes a VT82C5xx IDE interface). It has a single PATA connector (allowing thus max two PATA drives) and a CF connector soldered in the back of the board (allowing thus one CF and one PATA drive). The SanDisk Extreme IV CF I'm using is udma4 capable and rated for 40MB/s. The first problem: With a 2.6.24 kernel I see in dmesg: hda: drive side 80-wire cable detection failed, limiting max speed to UDMA33 hda: UDMA/33 mode selected and the CF drive is reported to work with udma2 by hdparm: DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Using dd for some testing, the max throughput "speed" reached is about 28MB/s, accordingly with the configuration above. However I discovered that using a 2.6.22 kernel, dmesg still reports that message but the kernel configures my CF to use udma4 as it should. Now dd shows a 38MB/s (about) "speed", reaching the maximum speed for this CF. Well, I don't really know how the CF slot is connected to the South Bridge but for sure there are really short traces, and I think I can safely say I had no data corruption using a 2.6.22 kernel and udma4 mode. Changing the disk BIOS settings has no influence at all. It seems I'm not the only one suffering this problem: http://crazyduke.blogspot.com/2007/12/cflinux.html It's not a big issue, really, but I'd like to understand why this happens and how to use my CF at full speed with udma4. The second problem: Adding a second HD (Maxtor PATA UDMA/133) results in a udma0 setting (for this drive, while the CF behaves normally) and in lots of errors in dmesg: [...] hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error } hdb: dma_intr: error=0x84 { DriveStatusError BadCRC } ide: failed opcode was: unknown hda: DMA disabled hdb: UDMA/100 mode selected ide0: reset: success [...] hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error } hdb: dma_intr: error=0x84 { DriveStatusError BadCRC } ide: failed opcode was: unknown hdb: no DMA mode selected ide0: reset: success ldm_validate_partition_table(): Disk read failed. Dev hdb: unable to read RDB block 0 unable to read partition table Once the system was up, only /dev/hdb had been created and I had to rewrite the partition table to the disk to see the partitions on it and correctly access them. However when I tried to set udma6 or udma4/2 with hdparm I obtained just a udma0 mode (infatc the system is lagging when coping files). I don't think I had data corruption, but in this case I'm not that sure. In the beginning I though that the CF does not want to share the ide channel with another device. However I had no problem when I connected a (really) old CDROM instead (using mdma2), for the system installation to the CF. Using a 2.6.22 or a 2.6.24 kernel makes no difference. Here it is a similar problem but without a solution: http://readlist.com/lists/vger.kernel.org/linux-kernel/69/348695.html Again, not a huge problem since I'm going to buy a larger SATA drive soon, but maybe it's usefull to understand why this happens. -- Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are the assignee for the bug, or are watching the assignee.