From: marius@psihoexpert.ro
To: "Damien Le Moal" <damien.lemoal@opensource.wdc.com>
Cc: linux-ide@vger.kernel.org
Subject: Re: Bug report for ahci-mvebu driver
Date: Tue, 24 Jan 2023 17:02:56 +0000 [thread overview]
Message-ID: <c7e1b214fca6c2a08dbce60006442dd8@psihoexpert.ro> (raw)
In-Reply-To: <f4d558fd-343a-8cb5-605d-574af42ad3db@opensource.wdc.com>
January 24, 2023 11:54 AM, "Damien Le Moal" <damien.lemoal@opensource.wdc.com> wrote:
> OK. Good. But from the trace below, it looks like you have the previous
> patch still applied. Can you try only the above patch ?
Done:
[ 15.135173][ T113] hardreset, Online=>Offline
[ 15.135182][ T113] sata_set_spd_needed, scontrol=0x300
[ 15.139656][ T113] __sata_set_spd_needed, initial limit=0xFFFFFFFF
[ 15.144934][ T113] __sata_set_spd_needed, corrected limit=0xFFFFFFFF
[ 15.151235][ T113] __sata_set_spd_needed, target=0x0
[ 15.157725][ T113] __sata_set_spd_needed, spd=0x0
[ 15.162805][ T113] __sata_set_spd_needed, final *scontrol=0x300
[ 15.168708][ T113] resume, do loop
[ 15.403902][ T113] resume, after do loop
[ 15.463901][ T113] debounce, SCR=0x100
[ 15.513923][ T113] debounce, SCR=0x101
[ 15.573901][ T113] debounce, SCR=0x100
[ 15.633901][ T113] debounce, SCR=0x101
[ 15.693901][ T113] debounce, SCR=0x100
[ 15.753901][ T113] debounce, SCR=0x101
[ 15.813900][ T113] debounce, SCR=0x100
[ 15.873901][ T113] debounce, SCR=0x101
[ 15.933900][ T113] debounce, SCR=0x100
[ 15.993900][ T113] debounce, SCR=0x100
[ 16.053900][ T113] debounce, SCR=0x100
[ 16.113901][ T113] debounce, SCR=0x100
[ 16.173900][ T113] debounce, SCR=0x100
[ 16.233901][ T113] debounce, SCR=0x0
[ 16.293901][ T113] debounce, SCR=0x0
[ 16.353900][ T113] debounce, SCR=0x0
[ 16.413901][ T113] debounce, SCR=0x0
[ 16.473901][ T113] debounce, SCR=0x100
[ 16.477586][ T113] resume, return at end of function
[ 16.481446][ T113] hardreset, ata_phys_link_offline check failed
[ 16.486550][ T113] ata2: SATA link down (SStatus 100 SControl 300)
[ 16.499019][ T113] sata_down_spd_limit: limit 0x1, cur spd 0x0, saved limit 0xffffffff, hw limit
0xffffffff
[ 16.508914][ T113] ata2: limiting SATA link speed to 1.5 Gbps
[ 16.514800][ T113] hardreset, Online=>Offline
[ 16.514807][ T113] sata_set_spd_needed, scontrol=0x300
[ 16.519276][ T113] __sata_set_spd_needed, initial limit=0x1
[ 16.524544][ T113] __sata_set_spd_needed, corrected limit=0x1
[ 16.530235][ T113] __sata_set_spd_needed, target=0x1
[ 16.536119][ T113] __sata_set_spd_needed, spd=0x0
[ 16.541199][ T113] __sata_set_spd_needed, final *scontrol=0x310
[ 16.546046][ T113] __sata_set_spd_needed, initial limit=0x1
[ 16.552085][ T113] __sata_set_spd_needed, corrected limit=0x1
[ 16.557790][ T113] __sata_set_spd_needed, target=0x1
[ 16.563655][ T113] __sata_set_spd_needed, spd=0x0
[ 16.568748][ T113] __sata_set_spd_needed, final *scontrol=0x314
[ 16.574637][ T113] resume, do loop
[ 16.803902][ T113] resume, after do loop
[ 16.863901][ T113] debounce, SCR=0x113
[ 16.923901][ T113] debounce, SCR=0x113
[ 16.983901][ T113] debounce, SCR=0x113
[ 17.043900][ T113] debounce, SCR=0x113
[ 17.103901][ T113] debounce, SCR=0x113
[ 17.163901][ T113] debounce, SCR=0x113
[ 17.223901][ T113] debounce, SCR=0x113
[ 17.283900][ T113] debounce, SCR=0x113
[ 17.343900][ T113] debounce, SCR=0x113
[ 17.347761][ T113] resume, return at end of function
[ 17.351620][ T113] hardreset, Offline=>Online
[ 17.361184][ T113] hardreset, sata_pmp_supported, before check_ready
[ 17.533905][ T113] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 17.547634][ T113] ata2.15: Port Multiplier 1.2, 0x197b:0x0325 r193, 8 ports, feat 0xf/0x1f
[ 17.556257][ T113] device: 'link2.0': device_add
[ 17.561066][ T113] device: 'link2.0': device_add
[ 17.566026][ T113] device: 'dev2.0.0': device_add
[ 17.570872][ T113] device: 'dev2.0.0': device_add
[ 17.575869][ T113] device: 'link2.1': device_add
[ 17.580628][ T113] device: 'link2.1': device_add
[ 17.585489][ T113] device: 'dev2.1.0': device_add
[ 17.590370][ T113] device: 'dev2.1.0': device_add
...
[ 17.830354][ T113] device: 'link2.14': device_add
[ 17.835236][ T113] device: 'link2.14': device_add
[ 17.840174][ T113] device: 'dev2.14.0': device_add
[ 17.845134][ T113] device: 'dev2.14.0': device_add
[ 17.850194][ T113] ahci-mvebu f10a8000.sata: FBS is enabled
[ 17.855948][ T113] ata2.00: SCR_CONTROL = 0x300
[ 17.860630][ T113] ata2.01: SCR_CONTROL = 0x300
[ 17.865332][ T113] ata2.02: SCR_CONTROL = 0x300
[ 17.870010][ T113] ata2.03: SCR_CONTROL = 0x300
[ 17.874720][ T113] ata2.04: SCR_CONTROL = 0x300
[ 17.879397][ T113] ata2.05: SCR_CONTROL = 0x300
[ 17.884140][ T113] ata2.06: SCR_CONTROL = 0x300
[ 17.888817][ T113] ata2.07: SCR_CONTROL = 0x300
[ 17.893568][ T113] ata2.00: hard resetting link
[ 17.898247][ T113] hardreset, Online=>Offline
[ 17.898287][ T113] sata_set_spd_needed, scontrol=0x300
[ 17.902759][ T113] __sata_set_spd_needed, initial limit=0xFFFFFFFF
[ 17.908037][ T113] __sata_set_spd_needed, corrected limit=0x1
[ 17.914351][ T113] __sata_set_spd_needed, target=0x1
[ 17.920217][ T113] __sata_set_spd_needed, spd=0x0
[ 17.925308][ T113] __sata_set_spd_needed, final *scontrol=0x310
[ 17.930221][ T113] __sata_set_spd_needed, initial limit=0xFFFFFFFF
[ 17.936287][ T113] __sata_set_spd_needed, corrected limit=0x1
[ 17.942587][ T113] __sata_set_spd_needed, target=0x1
[ 17.948465][ T113] __sata_set_spd_needed, spd=0x0
[ 17.953544][ T113] __sata_set_spd_needed, final *scontrol=0x310
[ 17.959580][ T113] resume, do loop
[ 18.193937][ T113] resume, after do loop
[ 18.202581][ T113] debounce, SCR=0x123
[ 18.211737][ T113] debounce, SCR=0x123
[ 18.220718][ T113] debounce, SCR=0x123
[ 18.229700][ T113] debounce, SCR=0x123
[ 18.238661][ T113] debounce, SCR=0x123
[ 18.247624][ T113] debounce, SCR=0x123
[ 18.256584][ T113] debounce, SCR=0x123
[ 18.265545][ T113] debounce, SCR=0x123
[ 18.274506][ T113] debounce, SCR=0x123
[ 18.283466][ T113] debounce, SCR=0x123
[ 18.292447][ T113] debounce, SCR=0x123
[ 18.301429][ T113] debounce, SCR=0x123
[ 18.305373][ T113] resume, return at end of function
[ 18.309265][ T113] hardreset, Offline=>Online
[ 18.318828][ T113] hardreset, after check_ready
[ 18.319045][ T113] ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 18.330915][ T113] ata2.01: hard resetting link
[ 18.335582][ T113] hardreset, Online=>Offline
[ 18.335619][ T113] sata_set_spd_needed, scontrol=0x300
[ 18.340090][ T113] __sata_set_spd_needed, initial limit=0xFFFFFFFF
[ 18.345365][ T113] __sata_set_spd_needed, corrected limit=0x1
[ 18.351665][ T113] __sata_set_spd_needed, target=0x1
[ 18.357543][ T113] __sata_set_spd_needed, spd=0x0
[ 18.362624][ T113] __sata_set_spd_needed, final *scontrol=0x310
[ 18.367549][ T113] __sata_set_spd_needed, initial limit=0xFFFFFFFF
[ 18.373589][ T113] __sata_set_spd_needed, corrected limit=0x1
[ 18.379911][ T113] __sata_set_spd_needed, target=0x1
[ 18.385790][ T113] __sata_set_spd_needed, spd=0x0
[ 18.390870][ T113] __sata_set_spd_needed, final *scontrol=0x310
[ 18.396900][ T113] resume, do loop
[ 18.623935][ T113] resume, after do loop
[ 18.632578][ T113] debounce, SCR=0x123
[ 18.641735][ T113] debounce, SCR=0x123
[ 18.650715][ T113] debounce, SCR=0x123
[ 18.659695][ T113] debounce, SCR=0x123
[ 18.668654][ T113] debounce, SCR=0x123
[ 18.677614][ T113] debounce, SCR=0x123
[ 18.686575][ T113] debounce, SCR=0x123
[ 18.695535][ T113] debounce, SCR=0x123
[ 18.704496][ T113] debounce, SCR=0x123
[ 18.713456][ T113] debounce, SCR=0x123
[ 18.722438][ T113] debounce, SCR=0x123
[ 18.731421][ T113] debounce, SCR=0x123
[ 18.735365][ T113] resume, return at end of function
[ 18.739256][ T113] hardreset, Offline=>Online
[ 18.748820][ T113] hardreset, after check_ready
[ 18.749041][ T113] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Marius Dinu
next prev parent reply other threads:[~2023-01-24 17:03 UTC|newest]
Thread overview: 67+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-11-01 19:21 Bug report for ahci-mvebu driver Dinu Marius
2022-11-06 7:05 ` Damien Le Moal
2022-11-07 9:22 ` marius
2022-11-08 6:27 ` Damien Le Moal
2022-11-09 19:52 ` marius
2022-11-09 19:55 ` marius
2022-11-10 2:05 ` Damien Le Moal
2022-11-11 22:32 ` marius
2022-11-12 1:57 ` Damien Le Moal
2022-11-14 20:52 ` marius
2022-11-15 3:02 ` Damien Le Moal
2022-11-15 7:28 ` marius
2022-11-15 8:10 ` Damien Le Moal
2022-11-18 18:24 ` Dinu Marius
2022-11-24 2:40 ` Damien Le Moal
2022-12-04 1:41 ` marius
2022-12-04 10:22 ` Pali Rohár
2022-12-04 21:14 ` marius
2022-12-04 21:46 ` Pali Rohár
2022-12-05 2:02 ` Damien Le Moal
2022-12-06 6:08 ` Damien Le Moal
2022-12-07 18:27 ` marius
2022-12-07 21:54 ` Damien Le Moal
2022-12-07 22:51 ` Damien Le Moal
2022-12-08 18:06 ` marius
2022-12-09 0:34 ` Damien Le Moal
2022-12-09 2:58 ` Damien Le Moal
2022-12-09 7:31 ` marius
2022-12-09 9:28 ` Damien Le Moal
2022-12-09 18:30 ` marius
2023-01-14 18:01 ` marius
2023-01-15 23:37 ` Damien Le Moal
2023-01-17 8:26 ` Damien Le Moal
2023-01-18 19:43 ` marius
2023-01-19 0:29 ` Damien Le Moal
2023-01-19 18:46 ` marius
2023-01-23 7:02 ` Damien Le Moal
2023-01-23 20:00 ` marius
2023-01-23 23:00 ` Damien Le Moal
2023-01-24 8:04 ` marius
2023-01-24 9:53 ` Damien Le Moal
2023-01-24 17:02 ` marius [this message]
2023-01-27 5:13 ` Damien Le Moal
2023-01-27 6:28 ` Damien Le Moal
2023-01-28 17:08 ` marius
2023-01-29 2:23 ` Damien Le Moal
2023-01-29 10:24 ` marius
2023-01-30 1:16 ` Damien Le Moal
2023-01-30 2:38 ` Damien Le Moal
2023-01-30 7:23 ` marius
2023-01-30 7:37 ` Damien Le Moal
2023-01-30 23:22 ` Damien Le Moal
2023-01-31 7:20 ` marius
2023-01-31 7:28 ` Damien Le Moal
2023-02-07 18:40 ` marius
2023-02-07 23:39 ` Damien Le Moal
2023-02-08 12:17 ` marius
2023-02-08 23:00 ` Damien Le Moal
2023-02-12 13:14 ` marius
2023-02-12 23:11 ` Damien Le Moal
2023-01-24 17:06 ` Bug report for sata_via driver marius
2023-01-25 1:26 ` Damien Le Moal
2022-12-08 21:26 ` Bug report for ahci-mvebu driver Pali Rohár
2022-12-09 1:54 ` Damien Le Moal
2022-11-26 14:26 ` Pali Rohár
2023-01-23 9:10 ` Hajo Noerenberg
2023-01-23 12:13 ` Damien Le Moal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=c7e1b214fca6c2a08dbce60006442dd8@psihoexpert.ro \
--to=marius@psihoexpert.ro \
--cc=damien.lemoal@opensource.wdc.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox