From: Nicolas STRANSKY <Nico@stransky.cx>
To: linux-ide@vger.kernel.org
Subject: IRQ problem with sata_sil
Date: Mon, 08 May 2006 12:00:29 +0200 [thread overview]
Message-ID: <e3n4ru$ktd$1@sea.gmane.org> (raw)
Hi all,
I've encountered a problem when trying to use a SATA card with a Silicon
Image SIL 3112 host controller chip. When inserting the module, the
kernel made this error:
> May 7 21:15:18 aneto kernel: sata_sil 0000:02:0c.0: version 1.0
> May 7 21:15:18 aneto kernel: PCI: Found IRQ 10 for device 0000:02:0c.0
> May 7 21:15:18 aneto kernel: PCI: Sharing IRQ 10 with 0000:02:05.0
> May 7 21:15:18 aneto kernel: ata1: SATA max UDMA/100 cmd 0xF8FBC080 ctl 0xF8FBC08A bmdma 0xF8FBC000 irq 10
> May 7 21:15:18 aneto kernel: ata2: SATA max UDMA/100 cmd 0xF8FBC0C0 ctl 0xF8FBC0CA bmdma 0xF8FBC008 irq 10
> May 7 21:15:18 aneto kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> May 7 21:15:18 aneto kernel: irq 10: nobody cared (try booting with the "irqpoll" option)
> May 7 21:15:18 aneto kernel: <c0131ad3> __report_bad_irq+0x2b/0x69 <c0131cd8> note_interrupt+0x1c7/0x1f7
> May 7 21:15:18 aneto kernel: <c0131660> __do_IRQ+0x8d/0xcd <c01043ad> do_IRQ+0x1d/0x28
> May 7 21:15:18 aneto kernel: <c0102cc2> common_interrupt+0x1a/0x20 <c0118237> __do_softirq+0x2c/0x7d
> May 7 21:15:18 aneto kernel: <c01182aa> do_softirq+0x22/0x26 <c011837f> irq_exit+0x29/0x34
> May 7 21:15:18 aneto kernel: <c01043b2> do_IRQ+0x22/0x28 <c0102cc2> common_interrupt+0x1a/0x20
> May 7 21:15:18 aneto kernel: <c016034c> __d_lookup+0x62/0x123 <c0157fa4> do_lookup+0x25/0x13f
> May 7 21:15:18 aneto kernel: <c015839e> __link_path_walk+0x2e0/0xbf6 <c01767b1> proc_delete_inode+0x22/0x75
> May 7 21:15:18 aneto kernel: <c0158cfd> link_path_walk+0x49/0xbb <c015919b> do_path_lookup+0x1a4/0x1d5
> May 7 21:15:18 aneto kernel: <c01593db> do_unlinkat+0x2f/0xff <c0357ca7> syscall_call+0x7/0xb
> May 7 21:15:18 aneto kernel: <c035007b> xfrm_aalg_get_byid+0x27/0x39
> May 7 21:15:18 aneto kernel: handlers:
> May 7 21:15:18 aneto kernel: [<c02d2c90>] (ata_interrupt+0x0/0x13f)
> May 7 21:15:18 aneto kernel: Disabling IRQ #10
> May 7 21:15:18 aneto kernel: ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
> May 7 21:15:18 aneto kernel: ata1: dev 0 ATA-6, max UDMA/133, 312581808 sectors: LBA48
> May 7 21:15:18 aneto kernel: ata1: dev 0 configured for UDMA/100
> May 7 21:15:18 aneto kernel: scsi1 : sata_sil
> May 7 21:15:18 aneto kernel: ata2: SATA link down (SStatus 0 SControl 310)
> May 7 21:15:18 aneto kernel: scsi2 : sata_sil
> May 7 21:15:18 aneto kernel: Vendor: ATA Model: ST3160827AS Rev: 3.42
> May 7 21:15:18 aneto kernel: Type: Direct-Access ANSI SCSI revision: 05
> May 7 21:15:18 aneto kernel: SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
> May 7 21:15:18 aneto kernel: sda: Write Protect is off
> May 7 21:15:18 aneto kernel: sda: Mode Sense: 00 3a 00 00
> May 7 21:15:18 aneto kernel: SCSI device sda: drive cache: write back
> May 7 21:15:18 aneto kernel: SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
> May 7 21:15:18 aneto kernel: sda: Write Protect is off
> May 7 21:15:18 aneto kernel: sda: Mode Sense: 00 3a 00 00
I've tried with both 2.6.16 and 2.6.17-rc3-mm1, each time with or
without the "irqpoll" boot option, but it always ended with the same error.
Please let me know if I can provide any additional information.
Thanks for support,
--
Nico
L'esprit nous sert quelquefois à faire hardiment des sottises.
-+- François de La Rochefoucauld (1613-1680), Maximes 415 -+-
next reply other threads:[~2006-05-08 10:05 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-05-08 10:00 Nicolas STRANSKY [this message]
2006-05-08 10:19 ` IRQ problem with sata_sil Paul M.
2006-05-09 5:39 ` Nicolas STRANSKY
2006-05-10 1:11 ` jason
2006-05-10 4:36 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='e3n4ru$ktd$1@sea.gmane.org' \
--to=nico@stransky.cx \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).