From: kenneth johansson <ken@kenjo.org>
To: linux-ide@vger.kernel.org
Subject: lost external eSATA port
Date: Sun, 29 Mar 2009 12:28:51 +0000 (UTC) [thread overview]
Message-ID: <gqnpi3$jq2$1@ger.gmane.org> (raw)
After an error on the external disk the port no longer work with any disk.
When the error happened the /dev/sdx was removed. if I change disk its never recreated.
I get no log output from kernel indicating any type of action at all.
Is there a way to reset the port ??
--------------
I have a
Base Board Information
Manufacturer: ASUSTeK Computer INC.
Product Name: P5B-V
Version: Rev 1.xx
board where I think the eSATA port is controlled by
IDE interface: Intel Corporation 82801H (ICH8 Family) 4 port SATA IDE Controller (rev 02)
or perhaps
SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02)
----------
kernel is 2.6.28.7
----------
this is the last kernel log regarding the esata port.
[ 2082.771431] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 2082.771440] ata3.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 2082.771442] cdb 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2082.771443] res 51/04:00:00:71:00/00:00:00:00:00/00 Emask 0x1 (device error)
[ 2082.771446] ata3.00: status: { DRDY ERR }
[ 2082.771613] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2082.771615] ata3.00: ST_FIRST: !(DRQ|ERR|DF)
[ 2082.771621] ata3.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 2082.771622] cdb 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2082.771623] res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x2 (HSM violation)
[ 2082.771643] ata3: soft resetting link
[ 2082.940837] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x2)
[ 2082.940840] ata3.00: revalidation failed (errno=-5)
[ 2092.944030] ata3: link is slow to respond, please be patient (ready=0)
[ 2097.964030] ata3: device not ready (errno=-16), forcing hardreset
[ 2097.964041] ata3: soft resetting link
[ 2098.128113] ata3.01: NODEV after polling detection
[ 2098.128273] ata1.00: exception Emask 0x60 SAct 0x0 SErr 0x800 action 0x6 frozen
[ 2098.128276] ata1.00: irq_stat 0x20000000, host bus error
[ 2098.128278] ata1: SError: { HostInt }
[ 2098.128282] ata1.00: cmd 35/00:00:00:0c:32/00:04:06:00:00/e0 tag 0 dma 524288 out
[ 2098.128283] res 50/00:00:ff:0b:32/00:00:06:00:00/e0 Emask 0x60 (host bus error)
[ 2098.128285] ata1.00: status: { DRDY }
[ 2098.128288] ata1: hard resetting link
[ 2098.136193] ata3.00: NODEV after polling detection
[ 2098.136196] ata3.00: revalidation failed (errno=-2)
[ 2098.952047] ata1: SATA link down (SStatus 0 SControl 71)
[ 2103.120039] ata3: soft resetting link
[ 2103.284188] ata3.00: NODEV after polling detection
[ 2103.284192] ata3.00: revalidation failed (errno=-2)
[ 2103.284196] ata3.00: disabled
[ 2103.284229] ata3: soft resetting link
[ 2103.440115] ata3: EH complete
[ 2103.952028] ata1: hard resetting link
[ 2104.776050] ata1: SATA link down (SStatus 0 SControl 71)
[ 2104.776060] ata1: limiting SATA link speed to 1.5 Gbps
[ 2109.806610] ata1: hard resetting link
[ 2110.628041] ata1: SATA link down (SStatus 0 SControl 71)
[ 2110.628050] ata1.00: disabled
[ 2110.628069] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 2110.628074] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 2110.628079] Descriptor sense data with sense descriptors (in hex):
[ 2110.628082] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 2110.628092] 06 32 0b ff
[ 2110.628096] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 2110.628101] end_request: I/O error, dev sda, sector 103943168
[ 2110.628118] ata1: EH complete
[ 2110.630096] ata1.00: detaching (SCSI 0:0:0:0)
[ 2110.634675] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 2110.634726] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
[ 2110.634731] sd 0:0:0:0: [sda] Stopping disk
[ 2110.634742] sd 0:0:0:0: [sda] START_STOP FAILED
[ 2110.634744] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
next reply other threads:[~2009-03-29 12:29 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-03-29 12:28 kenneth johansson [this message]
2009-03-30 8:44 ` lost external eSATA port Tejun Heo
2009-03-30 20:27 ` kenneth johansson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='gqnpi3$jq2$1@ger.gmane.org' \
--to=ken@kenjo.org \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).