Re: [PATCH 07/11] iio: adc: Add support for QCOM PMIC5 Gen3 ADC

[Jishnu Prakash <quic_jprakash@quicinc.com>]

Hi Krzysztof.

On 7/9/2023 11:11 PM, Krzysztof Kozlowski wrote:
> On 08/07/2023 09:28, Jishnu Prakash wrote:
>> The ADC architecture on PMIC5 Gen3 is similar to that on PMIC5 Gen2,
>> with all SW communication to ADC going through PMK8550 which
>> communicates with other PMICs through PBS. One major difference is
>> that the register interface used here is that of an SDAM present on
> ...
>
>
>> +static int adc5_gen3_probe(struct platform_device *pdev)
>> +{
>> +	struct device *dev = &pdev->dev;
>> +	struct iio_dev *indio_dev;

>> +		irq = platform_get_irq(pdev, i);
>> +		if (irq < 0) {
>> +			dev_err(adc->dev, "Failed to get SDAM%d irq, ret=%d\n", i, irq);
>> +			return irq;
> return dev_err_probe

Will update it in the next patchset

>
>> +		}
>> +		adc->base[i].irq = irq;
>> +
>> +		scnprintf(buf, sizeof(buf), "adc-sdam%d", i);
>> +		adc->base[i].irq_name = devm_kstrdup(adc->dev, buf, GFP_KERNEL);
>> +		if (!adc->base[i].irq_name)
>> +			return -ENOMEM;
>> +	}
>> +
>> +	platform_set_drvdata(pdev, adc);
>> +
>> +	init_completion(&adc->complete);
>> +	mutex_init(&adc->lock);
>> +
>> +	ret = adc5_get_fw_data(adc);
>> +	if (ret < 0) {
>> +		dev_err(adc->dev, "adc get dt data failed, ret=%d\n", ret);
> return dev_err_probe
Will update it in the next patchset
>
>> +		return ret;
>> +	}
>> +
>> +	for (i = 0; i < adc->num_sdams; i++) {
>> +		ret = devm_request_irq(dev, adc->base[i].irq, adc5_gen3_isr,
>> +					0, adc->base[i].irq_name, adc);
>> +		if (ret < 0) {
>> +			dev_err(adc->dev, "Getting IRQ %d failed, ret=%d\n", adc->base[i].irq, ret);
> return dev_err_probe
Will update it in the next patchset
>
>> +			return ret;
>> +		}
>> +	}
>> +
>> +	ret = adc_tm_register_tzd(adc);
>> +	if (ret < 0)
>> +		return ret;
>> +
>> +	if (adc->n_tm_channels)
>> +		INIT_WORK(&adc->tm_handler_work, tm_handler_work);
>> +
>> +	indio_dev->name = pdev->name;
>> +	indio_dev->modes = INDIO_DIRECT_MODE;
>> +	indio_dev->info = &adc5_gen3_info;
>> +	indio_dev->channels = adc->iio_chans;
>> +	indio_dev->num_channels = adc->nchannels;
>> +
>> +	return devm_iio_device_register(dev, indio_dev);
>> +}
>> +
>> +static int adc5_gen3_exit(struct platform_device *pdev)
>> +{
>> +	struct adc5_chip *adc = platform_get_drvdata(pdev);
>> +	u8 data = 0;
>> +	int i, sdam_index;
>> +
>> +	mutex_lock(&adc->lock);
>> +	/* Disable all available channels */
>> +	for (i = 0; i < adc->num_sdams * 8; i++) {
>> +		sdam_index = i / 8;
>> +		data = MEAS_INT_DISABLE;
>> +		adc5_gen3_write(adc, sdam_index, ADC5_GEN3_TIMER_SEL, &data, 1);
>> +
>> +		/* To indicate there is an actual conversion request */
>> +		data = ADC5_GEN3_CHAN_CONV_REQ | (i - (sdam_index * 8));
>> +		adc5_gen3_write(adc, sdam_index, ADC5_GEN3_PERPH_CH, &data, 1);
>> +
>> +		data = ADC5_GEN3_CONV_REQ_REQ;
>> +		adc5_gen3_write(adc, sdam_index, ADC5_GEN3_CONV_REQ, &data, 1);
>> +	}
>> +
>> +	mutex_unlock(&adc->lock);
>> +
>> +	if (adc->n_tm_channels)
>> +		cancel_work_sync(&adc->tm_handler_work);
>> +
>> +	return 0;
>> +}
>> +
>> +static struct platform_driver adc5_gen3_driver = {
>> +	.driver = {
>> +		.name = "qcom-spmi-adc5-gen3",
>> +		.of_match_table = adc5_match_table,
>> +	},
>> +	.probe = adc5_gen3_probe,
>> +	.remove = adc5_gen3_exit,
>> +};
>> +module_platform_driver(adc5_gen3_driver);
>> +
>> +MODULE_ALIAS("platform:qcom-spmi-adc5-gen3");
> Drop alias. If you need it, it means you screwed ID tables or your DTS.
>
>
> Best regards,
> Krzysztof


OK, I guess it's not needed, will drop it in the next patchset.

Thanks,

Jishnu


>