From: Jonathan Cameron <jic23@kernel.org>
To: Heiner Kallweit <hkallweit1@gmail.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-iio@vger.kernel.org
Subject: Re: [PATCH v2] iio: adc: meson-saradc: add calibration for meson gxbb
Date: Sun, 5 Mar 2017 12:08:30 +0000 [thread overview]
Message-ID: <13e3cdeb-5a9c-03df-4129-e38b13f63b58@kernel.org> (raw)
In-Reply-To: <89a21983-b722-cbb8-42db-13c447f2e527@gmail.com>
On 04/03/17 16:29, Heiner Kallweit wrote:
> The calibration on Meson GXBB is different from the one on GXM/GXL.
> This patch only supports GXBB as I don't have other spec and test hw.
> Points 25% vref and 75% vref are used for calibration.
>
> Adding a calibration scale resulted in no improvement, therefore
> only a simple calibration bias is supported.
You probably want to update this description ;)
>
> Successfully tested on a Odroid C2. Calibbias is 8 on my system.
>
> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
> ---
Looks good to me. Will want Martin's Ack on this, so I'll wait for that
before applying.
Jonathan
> v2:
> - added calibration scale
> ---
> drivers/iio/adc/meson_saradc.c | 74 ++++++++++++++++++++++++++++++++++++++++--
> 1 file changed, 72 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/iio/adc/meson_saradc.c b/drivers/iio/adc/meson_saradc.c
> index 23710088..d5aa0d04 100644
> --- a/drivers/iio/adc/meson_saradc.c
> +++ b/drivers/iio/adc/meson_saradc.c
> @@ -173,7 +173,9 @@
> .channel = _chan, \
> .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
> BIT(IIO_CHAN_INFO_AVERAGE_RAW), \
> - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \
> + BIT(IIO_CHAN_INFO_CALIBBIAS) | \
> + BIT(IIO_CHAN_INFO_CALIBSCALE), \
> .datasheet_name = "SAR_ADC_CH"#_chan, \
> }
>
> @@ -233,6 +235,8 @@ struct meson_sar_adc_priv {
> struct clk *adc_div_clk;
> struct clk_divider clk_div;
> struct completion done;
> + int calibbias;
> + int calibscale;
> };
>
> static const struct regmap_config meson_sar_adc_regmap_config = {
> @@ -252,6 +256,16 @@ static unsigned int meson_sar_adc_get_fifo_count(struct iio_dev *indio_dev)
> return FIELD_GET(MESON_SAR_ADC_REG0_FIFO_COUNT_MASK, regval);
> }
>
> +static int meson_sar_adc_calib_val(struct iio_dev *indio_dev, int val)
> +{
> + struct meson_sar_adc_priv *priv = iio_priv(indio_dev);
> + int tmp;
> +
> + tmp = div_s64((s64)val * priv->calibscale, 1000000) + priv->calibbias;
> +
> + return clamp(tmp, 0, (1 << priv->data->resolution) - 1);
> +}
> +
> static int meson_sar_adc_wait_busy_clear(struct iio_dev *indio_dev)
> {
> struct meson_sar_adc_priv *priv = iio_priv(indio_dev);
> @@ -303,7 +317,7 @@ static int meson_sar_adc_read_raw_sample(struct iio_dev *indio_dev,
> fifo_val = FIELD_GET(MESON_SAR_ADC_FIFO_RD_SAMPLE_VALUE_MASK,
> regval);
> fifo_val &= GENMASK(priv->data->resolution - 1, 0);
> - *val = fifo_val;
> + *val = meson_sar_adc_calib_val(indio_dev, fifo_val);
>
> return 0;
> }
> @@ -529,6 +543,15 @@ static int meson_sar_adc_iio_info_read_raw(struct iio_dev *indio_dev,
> *val2 = priv->data->resolution;
> return IIO_VAL_FRACTIONAL_LOG2;
>
> + case IIO_CHAN_INFO_CALIBBIAS:
> + *val = priv->calibbias;
> + return IIO_VAL_INT;
> +
> + case IIO_CHAN_INFO_CALIBSCALE:
> + *val = priv->calibscale / 1000000;
> + *val2 = priv->calibscale % 1000000;
> + return IIO_VAL_INT_PLUS_MICRO;
> +
> default:
> return -EINVAL;
> }
> @@ -754,6 +777,47 @@ static irqreturn_t meson_sar_adc_irq(int irq, void *data)
> return IRQ_HANDLED;
> }
>
> +static int meson_sar_adc_calib(struct iio_dev *indio_dev)
> +{
> + struct meson_sar_adc_priv *priv = iio_priv(indio_dev);
> + int ret, nominal0, nominal1, value0, value1;
> +
> + /* use points 25% and 75% for calibration */
> + nominal0 = (1 << priv->data->resolution) / 4;
> + nominal1 = (1 << priv->data->resolution) * 3 / 4;
> +
> + meson_sar_adc_set_chan7_mux(indio_dev, CHAN7_MUX_VDD_DIV4);
> + usleep_range(10, 20);
> + ret = meson_sar_adc_get_sample(indio_dev,
> + &meson_sar_adc_iio_channels[7],
> + MEAN_AVERAGING, EIGHT_SAMPLES, &value0);
> + if (ret < 0)
> + goto out;
> +
> + meson_sar_adc_set_chan7_mux(indio_dev, CHAN7_MUX_VDD_MUL3_DIV4);
> + usleep_range(10, 20);
> + ret = meson_sar_adc_get_sample(indio_dev,
> + &meson_sar_adc_iio_channels[7],
> + MEAN_AVERAGING, EIGHT_SAMPLES, &value1);
> + if (ret < 0)
> + goto out;
> +
> + if (value1 <= value0) {
> + ret = -EINVAL;
> + goto out;
> + }
> +
> + priv->calibscale = div_s64((nominal1 - nominal0) * 1000000LL,
> + value1 - value0);
> + priv->calibbias = nominal0 - div_s64((s64)value0 * priv->calibscale,
> + 1000000);
> + ret = 0;
> +out:
> + meson_sar_adc_set_chan7_mux(indio_dev, CHAN7_MUX_CH7_INPUT);
> +
> + return ret;
> +}
> +
> static const struct iio_info meson_sar_adc_iio_info = {
> .read_raw = meson_sar_adc_iio_info_read_raw,
> .driver_module = THIS_MODULE,
> @@ -893,6 +957,8 @@ static int meson_sar_adc_probe(struct platform_device *pdev)
> return PTR_ERR(priv->vref);
> }
>
> + priv->calibscale = 1000000;
> +
> ret = meson_sar_adc_init(indio_dev);
> if (ret)
> goto err;
> @@ -901,6 +967,10 @@ static int meson_sar_adc_probe(struct platform_device *pdev)
> if (ret)
> goto err;
>
> + ret = meson_sar_adc_calib(indio_dev);
> + if (ret)
> + goto err_hw;
> +
> platform_set_drvdata(pdev, indio_dev);
>
> ret = iio_device_register(indio_dev);
>
next prev parent reply other threads:[~2017-03-05 12:08 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-03-04 16:29 [PATCH v2] iio: adc: meson-saradc: add calibration for meson gxbb Heiner Kallweit
2017-03-05 12:08 ` Jonathan Cameron [this message]
2017-03-05 12:22 ` Heiner Kallweit
2017-03-18 14:04 ` Martin Blumenstingl
2017-03-18 18:30 ` Heiner Kallweit
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=13e3cdeb-5a9c-03df-4129-e38b13f63b58@kernel.org \
--to=jic23@kernel.org \
--cc=hkallweit1@gmail.com \
--cc=linux-iio@vger.kernel.org \
--cc=martin.blumenstingl@googlemail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox